Mike Christie [Tue, 6 Mar 2012 22:09:01 +0000 (16:09 -0600)]
[SCSI] iscsi class: fix gfp use in ping compl and host event
If a ping or host event were to occur when memory is low
we do not want to use GFP_KERNEL, because the paths
sending them cannot block for data to be written. These
paths might be needed to recover write paths. Use GFP_NOIO
instead.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Lee Duncan [Thu, 1 Mar 2012 20:41:01 +0000 (12:41 -0800)]
[SCSI] st: expand ability to write immediate filemarks
The st tape driver recently added the MTWEOFI ioctl, which writes
a tape filemark (EOF), like the MTWEOF ioctl, except that MTWEOFI
returns immediately. This makes certain applications, like backup
software, run much more quickly on buffered tape drives.
Since legacy applications do not know about this new MTWEOFI ioctl,
this patch adds a new ioctl option that tells the st driver to return
immediately when writing an EOF (i.e. a filemark). This new flag
is much like the existing flag that tells the st driver to perform
writes (and certain other IOs) immediately, but this new flag only
applies to writing EOFs.
This new feature is controlled via the MTSETDRVBUFFER ioctl, using
the newly-defined MT_ST_NOWAIT_EOF flag.
Use of this new feature is displayed via the sysfs tape "options"
attribute.
The st documentation was updated to mention this new flag, as well
as the problems that can occur from using it.
Signed-off-by: Lee Duncan <lduncan@suse.com> Acked-by: Kai Makisara <kai.makisara@kolumbus.fi> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:38:52 +0000 (22:38 -0500)]
[SCSI] lpfc 8.3.30: Update lpfc to version 8.3.30
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:38:42 +0000 (22:38 -0500)]
[SCSI] lpfc 8.3.30: Revert fix for Link Pull Causes I/O Failures
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:38:29 +0000 (22:38 -0500)]
[SCSI] lpfc 8.3.30: Added more T10 DIF debugfs error injection
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:38:13 +0000 (22:38 -0500)]
[SCSI] lpfc 8.3.30: Update copyright date for files modified in 2012
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:37:54 +0000 (22:37 -0500)]
[SCSI] lpfc 8.3.30: Fix handling of REG_VFI and cable pull.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:37:42 +0000 (22:37 -0500)]
[SCSI] lpfc 8.3.30: Enhancements for T10 DIF debugfs error injection
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:37:32 +0000 (22:37 -0500)]
[SCSI] lpfc 8.3.30: Change default DA_ID support from disabled to enabled
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:37:18 +0000 (22:37 -0500)]
[SCSI] lpfc 8.3.30: Flush reset register write
Used PCI configure space read to flush PCI function reset register write
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:37:07 +0000 (22:37 -0500)]
[SCSI] lpfc 8.3.30: Update copyright date for files modified in 2012
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:36:54 +0000 (22:36 -0500)]
[SCSI] lpfc 8.3.30: Fixed panic with extents and small blocks
Fixed system panic when extents enabled with large number of small blocks
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:36:40 +0000 (22:36 -0500)]
[SCSI] lpfc 8.3.30: Add -Werror compilation flag
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:36:29 +0000 (22:36 -0500)]
[SCSI] lpfc 8.3.30: Fixed the system panic during EEH recovery
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:36:15 +0000 (22:36 -0500)]
[SCSI] lpfc 8.3.30: Fix resource leak when acc fails for received plogi
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:35:58 +0000 (22:35 -0500)]
[SCSI] lpfc 8.3.30: Fix SLI4 driver module load and unload
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:35:34 +0000 (22:35 -0500)]
[SCSI] lpfc 8.3.30: Fix deadlock during adapter offline request
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:35:23 +0000 (22:35 -0500)]
[SCSI] lpfc 8.3.30: Fix RPI registered multiple times after HBA reset
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:34:19 +0000 (22:34 -0500)]
[SCSI] lpfc 8.3.30: Fix port and system failure in SLI4 FC function reset
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:33:52 +0000 (22:33 -0500)]
[SCSI] lpfc 8.3.30: Fix lack of LOGO with vport delete.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Fri, 2 Mar 2012 03:33:29 +0000 (22:33 -0500)]
[SCSI] lpfc 8.3.30: Make BA_ACC work on a fully qualified exchange
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds support for Universal Flash Storage(UFS)
host controllers. The UFS host controller driver
includes host controller initialization method.
The Initialization process involves following steps:
- Initiate UFS Host Controller initialization process by writing
to Host controller enable register
- Configure UFS Host controller registers with host memory space
datastructure offsets.
- Unipro link startup procedure
- Check for connected device
- Configure UFS host controller to process requests
- Enable required interrupts
- Configure interrupt aggregation
[jejb: fix warnings in 32 bit compile] Signed-off-by: Santosh Yaraganavi <santoshsy@gmail.com> Signed-off-by: Vinayak Holikatti <vinholikatti@gmail.com> Reviewed-by: Arnd Bergmann <arnd@linaro.org> Reviewed-by: Vishak G <vishak.g@samsung.com> Reviewed-by: Girish K S <girish.shivananjappa@linaro.org> Reviewed-by: Namjae Jeon <linkinjeon@gmail.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Lan Tianyu [Thu, 15 Mar 2012 03:11:31 +0000 (11:11 +0800)]
[SCSI] sd: Add runtime pm in the sd_check_events()
The sd_check_event() will be called periodly even when the device is in the
suspended status to check media event. The scsi_test_unit_ready() in the
sd_check_event() will issue scsi cmd request. Issuing scsi request when the
device is in the suspeneded status will cause problem. For example, when a usb
flash disk in the suspended status, scsi_test_unit_ready() issues a scsi
request. The request will be returned as failed because the usb device is not
active. The patch adds scsi_autopm_get_device() and scsi_autopm_put_device()
around scsi_test_unit_ready() in the sd_check_event() to resolve such problem.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Nilesh Javali [Mon, 27 Feb 2012 11:08:52 +0000 (03:08 -0800)]
[SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
For offload iSCSI like qla4xxx CHAP entries are stored in FLASH.
This patch adds support to list CHAP entries stored in FLASH and
delete specified CHAP entry from FLASH using iscsi tools.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com> Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Nilesh Javali [Mon, 27 Feb 2012 11:08:51 +0000 (03:08 -0800)]
[SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
For offload iSCSI like qla4xxx CHAP entries are stored in FLASH.
This patch adds support to list CHAP entries stored in FLASH and
delete specified CHAP entry from FLASH using iscsi tools.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com> Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Santosh Nayak [Sun, 26 Feb 2012 14:44:46 +0000 (20:14 +0530)]
[SCSI] pm8001: fix endian issue with code optimization.
1. Fix endian issue.
2. Fix the following warning :
" drivers/scsi/pm8001/pm8001_hwi.c:2932:32: warning: comparison
between ‘enum sas_device_type’ and ‘enum sas_dev_type’".
3. Few code optimization.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com> Acked-by: Jack Wang <jack_wang@usish.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In 'mpi_sata_completion', "pm8001_ha->lock" is first released.
It means lock is taken before, which is true for
the context A, as 'pm8001_ha->lock' is taken in 'pm8001_chip_isr()'
But for context B there is no lock taken before and pm8001_ha->lock
is unlocked in 'mpi_sata_completion()'. This may unlock the lock
taken in context A. Possible racing ??
If 'pm8001_ha->lock' is taken in 'process_oq()' instead of
'pm8001_chip_isr' then the above issue can be avoided.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com> Acked-by: Jack Wang <jack_wang@usish.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Santosh Nayak [Sun, 26 Feb 2012 13:33:30 +0000 (19:03 +0530)]
[SCSI] pm8001: Fix bogus interrupt state flag issue.
Static checker is giving following warning:
" error: calling 'spin_unlock_irqrestore()' with bogus flags"
The code flow is as shown below:
process_oq() --> process_one_iomb --> mpi_sata_completion
In 'mpi_sata_completion'
the first call for 'spin_unlock_irqrestore()' is with flags=0,
which is as good as 'spin_unlock_irq()' ( unconditional interrupt
enabling).
So for better performance 'spin_unlock_irqrestore()' can be replaced
with 'spin_unlock_irq()' and 'spin_lock_irqsave()' can be replaced by
'spin_lock_irq()'.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com> Acked-by: Jack Wang <jack_wang@usish.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Wayne Boyer [Thu, 23 Feb 2012 19:54:55 +0000 (11:54 -0800)]
[SCSI] ipr: update PCI ID definitions for new adapters
This patch updates some PCI ID definitions for new adapters based on the next
generation 64 bit IOA PCI interface chip.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Carpenter [Tue, 21 Feb 2012 07:29:40 +0000 (10:29 +0300)]
[SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
This silences a static checker warning. Also we're always adding new
types of firmware, so it might fix a bug in real life some day.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Andrzej Jakowski [Fri, 10 Feb 2012 09:18:54 +0000 (01:18 -0800)]
[SCSI] isci: improvements in driver unloading routine
This patch fixes scenario where driver removal should be possible
only when driver is in READY state. Also it removes redundant
invocation of routine disabling SCU interrupts - this method is
called somewhere else in driver deinitialization path.
Signed-off-by: Andrzej Jakowski <andrzej.jakowski@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Tue, 31 Jan 2012 05:40:45 +0000 (21:40 -0800)]
[SCSI] libsas: don't recover end devices attached to disabled phys
If userspace has decided to disable a phy the kernel should honor that
and not inadvertantly re-enable the phy via error recovery. This is
more straightforward in the sata case where link recovery (via
libata-eh) is separate from sas_task cancelling in libsas-eh. Teach
libsas to accept -ENODEV as a successful response from I_T_nexus_reset
('successful' in terms of not escalating further).
This is a more comprehensive fix then "libsas: don't recover 'gone'
devices in sas_ata_hard_reset()", as it is no longer sata-specific.
aic94xx does check the return value from sas_phy_reset() so if the phy
is disabled we proceed with clearing the I_T_nexus.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Thu, 9 Feb 2012 07:20:41 +0000 (23:20 -0800)]
[SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
If discovery returns 0 for target_port_protocols but shows an attached
sata device, just report SAS_PROTOCOL_SATA in the identify data so
userspace can reliably search for sata devices in the domain.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Fri, 20 Jan 2012 23:26:03 +0000 (15:26 -0800)]
[SCSI] libsas: revert ata srst
libata issues follow up srsts when the controller has a hard time
recording the signature-fis after a reset, or if the link supports port
multipliers. libsas does not support port multipliers and no current
libsas lldds appear to need help retrieving the signature fis. Revert
it for now to remove confusion.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Fri, 20 Jan 2012 23:23:07 +0000 (15:23 -0800)]
[SCSI] libsas: fix lifetime of SAS_HA_FROZEN
Until all sas_tasks are known to no longer be in-flight this flag gates late
completions from colliding with error handling. However, it must be cleared
prior to the submission of scsi_send_eh_cmnd() requests, otherwise those
commands will never be completed correctly.
This was spotted by slub debug:
=============================================================================
BUG sas_task: Objects remaining on kmem_cache_close()
-----------------------------------------------------------------------------
Dan Williams [Thu, 19 Jan 2012 04:47:01 +0000 (20:47 -0800)]
[SCSI] libsas: async ata scanning
libsas ata error handling is already async but this does not help the
scan case. Move initial link recovery out from under host->scan_mutex,
and delay synchronization with eh until after all port probe/recovery
work has been queued.
Device ordering is maintained with scan order by still calling
sas_rphy_add() in order of domain discovery.
Since we now scan the domain list when invoking libata-eh we need to be
careful to check for fully initialized ata ports.
Acked-by: Jack Wang <jack_wang@usish.com> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Thu, 19 Jan 2012 04:14:01 +0000 (20:14 -0800)]
[SCSI] libsas: restore scan order
ata devices are always scanned after ssp. Prior to the ata error
handling reworks libsas would tend to scan devices in ascending expander
phy order. Restore this ordering by deferring ssp discovery to a
DISCE_PROBE event, and keep the probe order consistent with the
discovery order, not the placement of sata devices.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Fri, 13 Jan 2012 01:57:35 +0000 (17:57 -0800)]
[SCSI] libsas: let libata recover links that fail to transmit initial sig-fis
libsas fails to discover all sata devices in the domain. If a device fails
negotiation and does not transmit a signature fis the link needs recovery.
libata already understands how to manage slow to come up links, so treat these
conditions as ata device attach events for the purposes of creating an
ata_port. This allows libata to manage retrying link bring up.
Rediscovery is modified to be careful about checking changes in dev_type. It
looks like libsas leaks old devices if the sas address changes, but that's a
fix for another patch.
Acked-by: Jack Wang <jack_wang@usish.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Mon, 16 Jan 2012 21:54:28 +0000 (13:54 -0800)]
[SCSI] libsas: fix sas port naming
Make sas-port naming consistent with the expander-attached case whereby
the phy-id is the last digit in the port name. Otherwise we get the
random behavior of the allocation order.
Reported-by: Patrick Thomson <patrick.s.thomson@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
which shows attached link rate, device type, and associates a
domain_device with its ata_port id to correlate messages emitted from
libata-eh.
As Doug notes, we can also take the opportunity to clarify expander phy
routing capabilities.
[dgilbert@interlog.com: clarify table2table with 'U'] Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Maciej Trela [Fri, 13 Jan 2012 21:52:38 +0000 (21:52 +0000)]
[SCSI] libsas: kill spurious sas_put_device
Holdover from a patch rework, prior to the addition of SAS_DEV_DESTROY
we were holding a reference while the destruct was pending in case the
domain was torn down before the desctruct event ran. That case is
covered by SAS_DEV_DESTROY, and the sas_put_device() just corrupts freed
memory, or worse frees the memory while another agent holds a reference.
Signed-off-by: Maciej Trela <maciej.trela@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Thu, 12 Jan 2012 19:47:24 +0000 (11:47 -0800)]
[SCSI] libsas: fix sas_unregister_ports vs sas_drain_work
We need to hold drain_mutex across the unregistration as port down events
queue device removal as chained events, so we need to make sure no other
drainers are active.
Reported-by: Jacek Danecki <jacek.danecki@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Wed, 11 Jan 2012 21:13:44 +0000 (13:13 -0800)]
[SCSI] libsas: route local link resets through ata-eh
Similar to the conversion of the transport-class reset we want bsg
initiated resets to be managed by libata.
Reported-by: Jacek Danecki <jacek.danecki@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Wed, 11 Jan 2012 20:08:36 +0000 (12:08 -0800)]
[SCSI] libsas: fix mixed topology recovery
If we have a domain with sas and sata devices there may still be sas
recovery actions to take after peeling off the commands to send to
libata.
Reported-by: Andrzej Jakowski <andrzej.jakowski@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Tue, 10 Jan 2012 23:14:09 +0000 (15:14 -0800)]
[SCSI] libsas: close scsi_remove_target() vs libata-eh race
ata_port lifetime in libata follows the host. In libsas it follows the
scsi_target. Once scsi_remove_device() has caused all commands to be
completed it allows scsi_remove_target() to immediately proceed to
freeing the ata_port causing bug reports like:
...so arrange for the ata_port to have the same end of life as the domain
device.
Reported-by: Marcin Tomczak <marcin.tomczak@intel.com> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Mon, 9 Jan 2012 18:12:52 +0000 (10:12 -0800)]
[SCSI] libsas: pre-clean commands that won the eh vs completion race
When scrolling forward through the eh list (in a clear_q scenario) it is
possible to encounter commands that won the completion vs eh race. Rather
than sprinkle more "if (!task)" throughout the handler just make a pass
through the list and delete the race winners before handling the rest.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Tue, 13 Dec 2011 04:32:09 +0000 (20:32 -0800)]
[SCSI] isci: remove IDEV_EH hack to disable "discovery-time" ata resets
Prior to commit 61aaff49 "isci: filter broadcast change notifications
during SMP phy resets" we borrowed the MVS_DEV_EH approach from the
mvsas driver for preventing ->lldd_I_T_nexus_reset() events during ata
discovery. This hack was protecting against the old ->phy_reset() in
ata_bus_probe(), but since the conversion to the new error handling this
hack is preventing resets from reaching ata devices.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Thu, 8 Dec 2011 08:37:25 +0000 (00:37 -0800)]
[SCSI] isci: remove bus and reset handlers
Remove ->eh_device_reset_handler() and ->eh_bus_reset_handler() for the
same reason they are not implemented for libata hosts, they cannot be
implemented reliably with ata-eh. ATA error recovery wants to divert
all resets to the eh thread and wait for completion, these handlers may
be invoked from a non-blocking ioctl.
The other path they are called from is libsas-eh, and if we escalate
past I_T_nexus reset we have larger problems i.e. tear down all
in-flight commands in the domain potentially without notification to the
lldd if it has chosen not to implement ->lldd_clear_nexus_port() /
->lldd_clear_nexus_ha().
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Fri, 9 Dec 2011 07:20:44 +0000 (23:20 -0800)]
[SCSI] isci: stop interpreting ->lldd_lu_reset() as an ata soft-reset
Driving resets from libsas-eh is pre-mature as libata will make a
decision about performing a softreset. Currently libata determines
whether to perform a softreset based on ata_eh_followup_srst_needed(),
and none of those conditions apply to isci.
Remove the srst implementation and translate ->lldd_lu_reset() for ata
devices as a request to drive a reset via libata-eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Wed, 30 Nov 2011 19:57:34 +0000 (11:57 -0800)]
[SCSI] isci: fix interpretation of "hard" reset
A hard reset to isci in the direct-attached case is one where the driver
internally manages debouncing the link. In the sas-expander-attached
case a hard reset is one that clears affiliations. The driver should
not be prematurely dropping affiliations at run time, that decision (to
force expander hard resets to ata devices) is left to userspace to
manage. So, arrange for I_T_nexus resets to be sas-link-resets in the
expander-attached case and isci-hard-resets in the direct-attached case.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Wed, 4 Jan 2012 07:26:15 +0000 (23:26 -0800)]
[SCSI] isci: kill isci_port->status
It only tracks whether the port is stopping in order to gate new devices
being discovered while the port is stopping. However, since the check
and subsequent handling is unlocked there is nothing to stop the port
from going down immediately after the check.
Driver is already prepared to handle devices arriving on stale ports,
and those will be cleaned up by an eventual ->lldd_dev_gone()
notification.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Wed, 4 Jan 2012 07:26:08 +0000 (23:26 -0800)]
[SCSI] isci: kill iphy->isci_port lookups
This field is a holdover from the OS abstraction conversion. The stable
phy to port lookups are done via iphy->ownining_port under scic_lock.
After this conversion to use port->lldd_port the only volatile lookup is
the initial lookup in isci_port_formed(). After that point any lookup
via a successfully notified domain_device is guaranteed to be valid
until the domain_device is destroyed.
Delete ->start_complete as it is only set once and is set as a
consequence of the port going link up, by definition of getting a port
formed event the port is "ready".
While we are correcting port lookups also move the asd_sas_port table
out from under the isci_port. This is to preclude any temptation to use
container_of() to convert an asd_sas_port to an isci_port, the
association is dynamic and under libsas control.
Tested-by: Maciej Trela <maciej.trela@intel.com>
[dmilburn@redhat.com: fix i686 compile error] Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Thu, 22 Dec 2011 22:58:24 +0000 (14:58 -0800)]
[SCSI] libsas: don't recover 'gone' devices in sas_ata_hard_reset()
The commands that timeout when a disk is forcibly removed may trigger
libata to attempt recovery of the device. If libsas has decided to
remove the device don't permit ata to continue to issue resets to its
last known phy.
The primary motivation for this patch is hotplug testing by writing 0 to
/sys/class/sas_phy/phyX/enable. Without this check this test leads to
libata issuing a reset and re-enabling the device that wants to be torn
down.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Thu, 22 Dec 2011 05:33:17 +0000 (21:33 -0800)]
[SCSI] libsas: fix sas_find_local_phy(), take phy references
In the direct-attached case this routine returns the phy on which this
device was first discovered. Which is broken if we want to support
wide-targets, as this phy reference can become stale even though the
port is still active.
In the expander-attached case this routine tries to lookup the phy by
scanning the attached sas addresses of the parent expander, and BUG_ONs
if it can't find it. However since eh and the libsas workqueue run
independently we can still be attempting device recovery via eh after
libsas has recorded the device as detached. This is even easier to hit
now that eh is blocked while device domain rediscovery takes place, and
that libata is fed more timed out commands increasing the chances that
it will try to recover the ata device.
Arrange for dev->phy to always point to a last known good phy, it may be
stale after the port is torn down, but it will catch up for wide port
reconfigurations, and never be NULL.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Wed, 21 Dec 2011 22:55:38 +0000 (14:55 -0800)]
[SCSI] libsas: don't mark expanders as gone when a child device is removed
Commit 56dd2c06 "[SCSI] libsas: Don't issue commands to devices that
have been hot-removed" marked the parent device of an end-device as gone
when all the phys to the end device have been deleted.
The expander device is still present until its parent is removed. This
is a benign change until the smp_execute_task() path is taught to check
->gone.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Fri, 18 Nov 2011 01:59:54 +0000 (17:59 -0800)]
[SCSI] libsas: poll for ata device readiness after reset
Use ata_wait_after_reset() to poll for link recovery after a reset.
This combined with sas_ha->eh_mutex prevents expander rediscovery from
probing phys in an intermediate state. Local discovery does not have a
mechanism to filter link status changes during this timeout, so it
remains the responsibility of lldds to prevent premature port teardown.
Although once all lldd's support ->lldd_ata_check_ready() that could be
used as a gate to local port teardown.
The signature fis is re-transmitted when the link comes back so we
should be revalidating the ata device class, but that is left to a future
patch.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Sun, 4 Dec 2011 09:06:24 +0000 (01:06 -0800)]
[SCSI] libsas: async ata-eh
Once sas_ata_hard_reset() starts honoring the 'deadline' parameter a
pathological configuration could take 25 seconds per ata device
(serialized) to recover. Run per-port recoveries in parallel.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Jeff Skirvin [Wed, 16 Nov 2011 09:44:13 +0000 (09:44 +0000)]
[SCSI] libsas: add mutex for SMP task execution
SAS does not tag SMP requests, and at least one lldd (isci) does not permit
more than one in-flight request at a time.
[jejb: fix sas_init_dev tab issues while we're at it] Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Jeff Skirvin [Fri, 16 Dec 2011 08:21:21 +0000 (08:21 +0000)]
[SCSI] libsas: Remove redundant phy state notification calls.
In the case of an explicit sas_phy_enable call to disable a phy,
the LLDD provides the calls to sas_phy_disconnected and the
PHYE_LOSS_OF_SIGNAL event.
NOTE: This assumes that the lldd(s) generate the notification, which
appears to be the case, but only verfied on isci.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Sat, 3 Dec 2011 00:07:01 +0000 (16:07 -0800)]
[SCSI] libsas: execute transport link resets with libata-eh via host workqueue
Link resets leave ata affiliations intact, so arrange for libsas to make
an effort to avoid dropping the device due to a slow-to-recover link.
Towards this end carry out reset in the host workqueue so that it can
check for ata devices and kick the reset request to libata. Hard
resets, in contrast, bypass libata since they are meant for associating
an ata device with another initiator in the domain (tears down
affiliations).
Need to add a new transport_sas_phy_reset() since the current
sas_phy_reset() is a utility function to libsas lldds. They are not
prepared for it to loop back into eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Tue, 20 Dec 2011 09:03:48 +0000 (01:03 -0800)]
[SCSI] libsas: perform sas-transport resets in shost->workq context
Extend the sas transport class to allow transport users to attach extra
data to a sas_phy (->hostdata). Use this area in libsas to move resets
to workq context in preparation for scheduling ata device resets through
libata-eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Thu, 1 Dec 2011 07:23:33 +0000 (23:23 -0800)]
[SCSI] libsas: use libata-eh-reset for sata rediscovery fis transmit failures
Since sata devices can take several seconds to recover the link on reset
the 0.5 seconds that libsas currently waits may not be enough. Instead
if we are rediscovering a phy that was previously attached to a sata
device let libata handle any resets to encourage the device to transmit
the initial fis.
Once sas_ata_hard_reset() and lldds learn how to honor 'deadline' libsas
should stop encountering phys in an intermediate state, until then this
will loop until the fis is transmitted or ->attached_sas_addr gets
cleared, but in the more likely initial discovery case we keep existing
behavior.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Tue, 29 Nov 2011 22:54:28 +0000 (14:54 -0800)]
[SCSI] libsas: defer SAS_TASK_NEED_DEV_RESET commands to libata
lldds use the SAS_TASK_NEED_DEV_RESET interface to request that eh
perform a reset. In the sata device case defer the commands that
triggered the reset to libata-eh context so it can perform its pre and
post reset management.
In the sas_ata_post_internal() case the reset request is falling on deaf
ears as the sas_task is immediately destroyed without any reset action.
Since it is currently a nop, and likely superfluous given the conversion
to new-style libata-eh, just drop the request.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Tue, 29 Nov 2011 20:08:50 +0000 (12:08 -0800)]
[SCSI] libsas: let libata handle command timeouts
libsas-eh if it successfully aborts an ata command will hide the timeout
condition (AC_ERR_TIMEOUT) from libata. The command likely completes
with the all-zero task->task_status it started with. Instead, interpret
a TMF_RESP_FUNC_COMPLETE as the end of the sas_task but keep the scmd
around for libata-eh to handle.
Tested-by: Andrzej Jakowski <andrzej.jakowski@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Mon, 28 Nov 2011 19:29:20 +0000 (11:29 -0800)]
[SCSI] libsas: fix timeout vs completion race
Until we have told the lldd to forget a task a timed out operation can
return from the hardware at any time. Since completion frees the task
we need to make sure that no tasks run their normal completion handler
once eh has decided to manage the task. Similar to
ata_scsi_cmd_error_handler() freeze completions to let eh judge the
outcome of the race.
Task collector mode is problematic because it presents a situation where
a task can be timed out and aborted before the lldd has even seen it.
For this case we need to guarantee that a task that an lldd has been
told to forget does not get queued after the lldd says "never seen it".
With sas_scsi_timed_out we achieve this with the ->task_queue_flush
mutex, rather than adding more time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Wed, 7 Dec 2011 07:24:42 +0000 (23:24 -0800)]
[SCSI] libsas: prevent double completion of scmds from eh
We invoke task->task_done() to free the task in the eh case, but at this
point we are prepared for scsi_eh_flush_done_q() to finish off the scmd.
Introduce sas_end_task() to capture the final response status from the
lldd and free the task.
Also take the opportunity to kill this warning.
drivers/scsi/libsas/sas_scsi_host.c: In function ‘sas_end_task’:
drivers/scsi/libsas/sas_scsi_host.c:102:3: warning: case value ‘2’ not in enumerated type ‘enum exec_status’ [-Wswitch]
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Mon, 28 Nov 2011 20:08:22 +0000 (12:08 -0800)]
[SCSI] libsas: close error handling vs sas_ata_task_done() race
Since sas_ata does not implement ->freeze(), completions for scmds and
internal commands can still arrive concurrent with
ata_scsi_cmd_error_handler() and sas_ata_post_internal() respectively.
By the time either of those is called libata has committed to completing
the qc, and the ATA_PFLAG_FROZEN flag tells sas_ata_task_done() it has
lost the race.
In the sas_ata_post_internal() case we take on the additional
responsibility of freeing the sas_task to close the race with
sas_ata_task_done() freeing the the task while sas_ata_post_internal()
is in the process of invoking ->lldd_abort_task().
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Tue, 29 Nov 2011 01:11:33 +0000 (17:11 -0800)]
[SCSI] libsas: kill invocation of scsi_eh_finish_cmd from sas_ata_task_done
Prior to the conversion to the new-style libata-eh sas_ata_task_done()
may have been the last opportunity to clean up the scmd, but now
libata-eh explicitly handles this case. It also races against sas-eh.
If a lldd completes a task after SAS_TASK_STATE_ABORTED is set it could
trigger a spurious decrement of shost->host_failed. Current lldds have
the band-aid of checking SAS_TASK_STATE_ABORTED before calling
->task_done(), but better to just let the scmds escalate to libata for
race free cleanup.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Fri, 18 Nov 2011 01:59:52 +0000 (17:59 -0800)]
[SCSI] libsas: use ->set_dmamode to notify lldds of NCQ parameters
sas_discover_sata() notifies lldds of sata devices twice. Once to allow
the 'identify' to be sent, and a second time to allow aic94xx (the only
libsas driver that cares about sata_dev.identify) to setup NCQ
parameters before the device becomes known to the midlayer. Replace
this double notification and intervening 'identify' with an explicit
->lldd_ata_set_dmamode notification. With this change all ata internal
commands are issued by libata, so we no longer need sas_issue_ata_cmd().
The data from the identify command only needs to be cached in one
location so ata_device.id replaces domain_device.sata_dev.identify.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Fri, 18 Nov 2011 01:59:51 +0000 (17:59 -0800)]
[SCSI] libsas: prevent domain rediscovery competing with ata error handling
libata error handling provides for a timeout for link recovery. libsas
must not rescan for previously known devices in this interval otherwise
it may remove a device that is simply waiting for its link to recover.
Let libata-eh make the determination of when the link is stable and
prevent libsas (host workqueue) from taking action while this
determination is pending.
Using a mutex (ha->disco_mutex) to flush and disable revalidation while
eh is running requires any discovery action that may block on eh be
moved to its own context outside the lock. Probing ATA devices
explicitly waits on ata-eh and the cache-flush-io issued during device
removal may also pend awaiting eh completion. Essentially any rphy
add/remove activity needs to run outside the lock.
This adds two new cleanup states for sas_unregister_domain_devices()
'allocated-but-not-probed', and 'flagged-for-destruction'. In the
'allocated-but-not-probed' state dev->rphy points to a rphy that is
known to have not been through a sas_rphy_add() event. At domain
teardown check if this device is still pending probe and cleanup
accordingly. Similarly if a device has already been queued for removal
then sas_unregister_domain_devices has nothing to do.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Fri, 18 Nov 2011 01:59:50 +0000 (17:59 -0800)]
[SCSI] libsas: remove ata_port.lock management duties from lldds
Each libsas driver (mvsas, pm8001, and isci) has invented a different
method for managing the ap->lock. The lock is held by the ata
->queuecommand() path. mvsas drops it prior to acquiring any internal
locks which allows it to hold its internal lock across calls to
task->task_done(). This capability is important as it is the only way
the driver can flush task->task_done() instances to guarantee that it no
longer has any in-flight references to a domain_device at
->lldd_dev_gone() time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Tue, 20 Dec 2011 00:42:34 +0000 (16:42 -0800)]
[SCSI] libsas: introduce sas_drain_work()
When an lldd invokes ->notify_port_event() it can trigger a chain of libsas
events to:
1/ form the port and find the direct attached device
2/ if the attached device is an expander perform domain discovery
A call to flush_workqueue() will only flush the initial port formation work.
Currently libsas users need to call scsi_flush_work() up to the max depth of
chain (which will grow from 2 to 3 when ata discovery is moved to its own
discovery event). Instead of open coding multiple calls switch to use
drain_workqueue() to flush sas work.
drain_workqueue() does not handle new work submitted during the drain so
libsas needs a bit of infrastructure to hold off unchained work submissions
while a drain is in flight. A lldd ->notify() event is considered 'unchained'
while a sas_discover_event() is 'chained'. As Tejun notes:
"For now, I think it would be best to add private wrapper in libsas to
support deferring unchained work items while draining."
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Fri, 18 Nov 2011 01:59:48 +0000 (17:59 -0800)]
[SCSI] libsas: fix leak of dev->sata_dev.identify_[packet_]device
These are never freed in the nominal path. A domain_device has a
different lifetime than a sas_rphy we need a dev->rphy independent way
of identifying sata devices.
Reviewed-by: Jack Wang <jack_wang@usish.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
projects / linux-beck.git / log