Jan Grossmann reported kernel boot panic while booting SMP
kernel on his system with a single core cpu. SMP kernels call
enable_IR_x2apic() from native_smp_prepare_cpus() and on
platforms where the kernel doesn't find SMP configuration we
ended up again calling enable_IR_x2apic() from the
APIC_init_uniprocessor() call in the smp_sanity_check(). Thus
leading to kernel panic.
Don't call enable_IR_x2apic() and default_setup_apic_routing()
from APIC_init_uniprocessor() in CONFIG_SMP case.
NOTE: this kind of non-idempotent and assymetric initialization
sequence is rather fragile and unclean, we'll clean that up
in v2.6.35. This is the minimal fix for v2.6.34.
On Wed, Feb 24, 2010 at 03:37:04PM -0800, Justin Piszcz wrote:
> Hello,
>
> Again, on the Intel DP55KG board:
>
> # uname -a
> Linux host 2.6.33 #1 SMP Wed Feb 24 18:31:00 EST 2010 x86_64 GNU/Linux
>
> [ 1.237600] ------------[ cut here ]------------
> [ 1.237890] WARNING: at arch/x86/kernel/hpet.c:404 hpet_next_event+0x70/0x80()
> [ 1.238221] Hardware name:
> [ 1.238504] hpet: compare register read back failed.
> [ 1.238793] Modules linked in:
> [ 1.239315] Pid: 0, comm: swapper Not tainted 2.6.33 #1
> [ 1.239605] Call Trace:
> [ 1.239886] <IRQ> [<ffffffff81056c13>] ? warn_slowpath_common+0x73/0xb0
> [ 1.240409] [<ffffffff81079608>] ? tick_dev_program_event+0x38/0xc0
> [ 1.240699] [<ffffffff81056cb0>] ? warn_slowpath_fmt+0x40/0x50
> [ 1.240992] [<ffffffff81079608>] ? tick_dev_program_event+0x38/0xc0
> [ 1.241281] [<ffffffff81041ad0>] ? hpet_next_event+0x70/0x80
> [ 1.241573] [<ffffffff81079608>] ? tick_dev_program_event+0x38/0xc0
> [ 1.241859] [<ffffffff81078e32>] ? tick_handle_oneshot_broadcast+0xe2/0x100
> [ 1.246533] [<ffffffff8102a67a>] ? timer_interrupt+0x1a/0x30
> [ 1.246826] [<ffffffff81085499>] ? handle_IRQ_event+0x39/0xd0
> [ 1.247118] [<ffffffff81087368>] ? handle_edge_irq+0xb8/0x160
> [ 1.247407] [<ffffffff81029f55>] ? handle_irq+0x15/0x20
> [ 1.247689] [<ffffffff810294a2>] ? do_IRQ+0x62/0xe0
> [ 1.247976] [<ffffffff8146be53>] ? ret_from_intr+0x0/0xa
> [ 1.248262] <EOI> [<ffffffff8102f277>] ? mwait_idle+0x57/0x80
> [ 1.248796] [<ffffffff8102645c>] ? cpu_idle+0x5c/0xb0
> [ 1.249080] ---[ end trace db7f668fb6fef4e1 ]---
>
> Is this something Intel has to fix or is it a bug in the kernel?
This is a chipset erratum.
Thomas: You mentioned we can retain this check only for known-buggy and
hpet debug kind of options. But here is the simple workaround patch for
this particular erratum.
Some chipsets have a erratum due to which read immediately following a
write of HPET comparator returns old comparator value instead of most
recently written value.
Erratum 15 in
"Intel I/O Controller Hub 9 (ICH9) Family Specification Update"
(http://www.intel.com/assets/pdf/specupdate/316973.pdf)
Workaround for the errata is to read the comparator twice if the first
one fails.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
LKML-Reference: <20100225185348.GA9674@linux-os.sc.intel.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: Venkatesh Pallipadi <venkatesh.pallipadi@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Colin King reported a strange oops in S4 resume code path (see below). The test
system has i5/i7 CPU. The kernel doesn't open PAE, so 4M page table is used.
The oops always happen a virtual address 0xc03ff000, which is mapped to the
last 4k of first 4M memory. Doing a global tlb flush fixes the issue.
Tested-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Shaohua Li <shaohua.li@intel.com>
LKML-Reference: <20100305005932.GA22675@sli10-desk.sh.intel.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
98e12b5a6e05413 ("ARM: Fix decompressor's kernel size estimation for
ROM=y") broke the Thumb-2 decompressor because it added an entry in the
LC0 table but didn't adjust the offset the Thumb-2 code uses to load the
SP from that table. Fix it.
Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For 4965, need to check it is valid qos frame before free, only valid
QoS frame has the tid used to free the packets.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
By doing this we always overwrite nbytes value that is being passed on to
CIFSSMBWrite() and need not rely on the callers to initialize. CIFSSMBWrite2 is
doing this already.
Reviewed-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com> Reviewed-by: Jeff Layton <jlayton@samba.org> Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While chasing a bug report involving a OS/2 server, I noticed the server sets
pSMBr->CountHigh to a incorrect value even in case of normal writes. This
results in 'nbytes' being computed wrongly and triggers a kernel BUG at
mm/filemap.c.
Why the server is setting 'CountHigh' is not clear but only does so after
writing 64k bytes. Though this looks like the server bug, the client side
crash may not be acceptable.
The workaround is to mask off high 16 bits if the number of bytes written as
returned by the server is greater than the bytes requested by the client as
suggested by Jeff Layton.
Reviewed-by: Jeff Layton <jlayton@samba.org> Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thank you for contacting us. We know that with our M225 line of SSDs
you sometimes need to disable NCQ (native command queuing) to avoid
just the type of errors you're seeing. Our recommendation for the
M225 is to add libata.force=noncq to your Linux kernel boot options,
under the kernel ATA library option.
I have sent your feedback to the engineers working on the C300, and
asked them to please pass it on to the firmware team. I have been
notified that they are in the process of testing and finalizing a
new firmware version, that you can expect to see released around the
end of April. We’ll keep you posted as to when it will be available
for download.
So, turn off NCQ on the drive w/ the current firmware revision.
Reported in the following bug.
https://bugzilla.kernel.org/show_bug.cgi?id=15573
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: lethalwp@scarlet.be Reported-by: Luke Macken <lmacken@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some new models need to disable wireless hotplug.
For the moment, we don't know excactly what models need that,
except 1005HA.
Users will be able to use that param as a workaround.
[bwh: Backported to 2.6.32]
Signed-off-by: Corentin Chary <corentincj@iksaif.net> Signed-off-by: Len Brown <len.brown@intel.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The EeePC 4G ("701") implements CFVS, but it is not supported by the
pre-installed OS, and the original option to change it in the BIOS
setup screen was removed in later versions. Judging by the lack of
"Super Hybrid Engine" on Asus product pages, this applies to all "701"
models (4G/4G Surf/2G Surf).
So Asus made a deliberate decision not to support it on this model.
We have several reports that using it can cause the system to hang [1].
That said, it does not happen all the time. Some users do not
experience it at all (and apparently wish to continue "right-clocking").
Check for the EeePC 701 using DMI. If met, then disable writes to the
"cpufv" sysfs attribute and log an explanatory message.
Add a "cpufv_disabled" attribute which allow users to override this
policy. Writing to this attribute will log a second message.
The sysfs attribute is more useful than a module option, because it
makes it easier for userspace scripts to provide consistent behaviour
(according to user configuration), regardless of whether the kernel
includes this change.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk> Signed-off-by: Corentin Chary <corentincj@iksaif.net> Signed-off-by: Len Brown <len.brown@intel.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Given the right combination of ThinkPad and X.org, just reading the
video output control state is enough to hard-crash X.org.
Until the day I somehow find out a model or BIOS cut date to not
provide this feature to ThinkPads that can do video switching through
X RandR, change permissions so that only processes with CAP_SYS_ADMIN
can access any sort of video output control state.
This bug could be considered a local DoS I suppose, as it allows any
non-privledged local user to cause some versions of X.org to
hard-crash some ThinkPads.
We already log the initial state of the hardware rfkill switch (WLSW),
might as well log the state of the softswitches as well.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Cc: Josip Rodin <joy+kernel@entuzijast.net> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before we register the input device, sync the input layer EV_SW state
through a call to input_report_switch(), to avoid issuing a gratuitous
event for the initial state of these switches.
This fixes some annoyances caused by the interaction with rfkill and
EV_SW SW_RFKILL_ALL events.
Reported-by: Kevin Locke <kevin@kevinlocke.name> Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Log temperatures on any of the EC thermal alarms. It could be
useful to help tracking down what is happening...
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Export the normal (non-command) module paramenters as mode 0444, so
that they will show up in sysfs.
These parameters must not be changed at runtime as a rule, with very
few exceptions.
Reported-by: Ferenc Wagner <wferi@niif.hu> Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Properly init the parent field of the input device. Thanks to Alan
Jenkins, who noted this problem in a different driver.
Reported-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk> Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix this bogus warning during module shutdown, when
backlight event reporting is enabled:
"thinkpad_acpi: required events 0x00018000 not enabled!"
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Take advantage of the new events capabilities of the backlight class to
notify userspace of backlight changes.
This depends on "backlight: Allow drivers to update the core, and
generate events on changes", by Matthew Garrett.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Cc: Matthew Garrett <mjg@redhat.com> Cc: Richard Purdie <rpurdie@linux.intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ext3_xattr_set_handle() was zeroing out an inode outside
of journaling constraints; this is one of the accesses that
was causing the crc errors in journal replay as seen in
kernel.org bugzilla #14354.
Although ext3 doesn't have the crc issue, modifications
out of journal control are a Bad Thing.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz> Cc: maximilian attems <max@stro.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit a71ce8c6c9bf269b192f352ea555217815cf027e updated ext3_statfs()
to update the on-disk superblock counters, but modified this buffer
directly without any journaling of the change. This is one of the
accesses that was causing the crc errors in journal replay as seen in
kernel.org bugzilla #14354.
The modifications were originally to keep the sb "more" in sync,
so that a readonly fsck of the device didn't flag this as an
error (as often), but apparently e2fsprogs deals with this differently
now, anyway.
Based on Ted's patch for ext4, which was in turn based on my
work on that bug and another preliminary patch...
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz> Cc: maximilian attems <max@stro.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
svm_vcpu_reset() was not properly resetting the contents of the guest-visible
cr0 register, causing the following issue:
https://bugzilla.redhat.com/show_bug.cgi?id=525699
Without resetting cr0 properly, the vcpu was running the SIPI bootstrap routine
with paging enabled, making the vcpu get a pagefault exception while trying to
run it.
Instead of setting vmcb->save.cr0 directly, the new code just resets
kvm->arch.cr0 and calls kvm_set_cr0(). The bits that were set/cleared on
vmcb->save.cr0 (PG, WP, !CD, !NW) will be set properly by svm_set_cr0().
kvm_set_cr0() is used instead of calling svm_set_cr0() directly to make sure
kvm_mmu_reset_context() is called to reset the mmu to nonpaging mode.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We intercept #BP while in guest debugging mode. As VM exits due to
intercepted exceptions do not necessarily come with valid
idt_vectoring, we have to update event_exit_inst_len explicitly in such
cases. At least in the absence of migration, this ensures that
re-injections of #BP will find and use the correct instruction length.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add proper error and permission checking. This patch also change task
switching code to load segment selectors before segment descriptors, like
SDM requires, otherwise permission checking during segment descriptor
loading will be incorrect.
Signed-off-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently when x86 emulator needs to access memory, page walk is done with
broadest permission possible, so if emulated instruction was executed
by userspace process it can still access kernel memory. Fix that by
providing correct memory access to page walker during emulation.
Signed-off-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For some instructions CPU behaves differently for real-mode and
virtual 8086. Let emulator know which mode cpu is in, so it will
not poke into vcpu state directly.
Signed-off-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use NodeId MSR to get NodeId and number of nodes per processor.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20091216144355.GB28798@alberich.amd.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/551606
The OR's hardware distorts at PCM 100% because it does not correspond to
0 dB. Fix this in patch_ad1981() for all models using the Thinkpad
quirk.
Reported-by: Jane Silber Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original code doesn't take into consideration that the value of
MIXART_BA0_SIZE - pos can be less than zero which would lead to a large
unsigned value for "count".
Also I moved the check that read size is a multiple of 4 bytes below
the code that adjusts "count".
We now call through generic_file_aio_write -> generic_write_sync ->
vfs_fsync_range. vfs_fsync_range has:
if (!fop || !fop->fsync) {
ret = -EINVAL;
goto out;
}
But drivers/char/raw.c doesn't set an fsync method.
We have two options: fix it or remove the raw driver completely. I'm
happy to do either, the fact this has been broken for so long suggests it
is rarely used.
The patch below adds an fsync method to the raw driver. My knowledge of
the block layer is pretty sketchy so this could do with a once over.
If we instead decide to remove the raw driver, this patch might still be
useful as a backport to 2.6.33 and 2.6.32.
Signed-off-by: Anton Blanchard <anton@samba.org> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Christoph Hellwig <hch@lst.de> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Jens Axboe <jens.axboe@oracle.com> Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Tested-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Making the new stuff work broke some of the old chipsets. We need to go
back to the old set up values for these it seems. Unfortunately even with
documentation this is basically a mix of cargoculting and guesswork.
Chased down to the exact line by Gianluca.
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Cc: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Originally the driver was only targeted to 12bits sensors. When support
for 8bits sensors was added, some slight difference in the registers were
overlooked. This should fix it, both for initialization, and for
displaying the rate.
Network folks reported that directing all MSI-X vectors of their multi
queue NICs to a single core can cause interrupt stack overflows when
enough interrupts fire at the same time.
This is caused by the fact that we run interrupt handlers by default
with interrupts enabled unless the driver reuqests the interrupt with
the IRQF_DISABLED set. The NIC handlers do not set this flag, so
simultaneous interrupts can nest unlimited and cause the stack
overflow.
The only safe counter measure is to run the interrupt handlers with
interrupts disabled. We can't switch to this mode in general right
now, but it is safe to do so for MSI interrupts.
Force IRQF_DISABLED for MSI interrupt handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andi Kleen <andi@firstfloor.org> Cc: Linus Torvalds <torvalds@osdl.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: David Miller <davem@davemloft.net> Cc: Greg Kroah-Hartman <gregkh@suse.de> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When there is a need to restart/reconfig hw, tear down all the
aggregation queues and let the mac80211 and driver get in-sync to have
the opportunity to re-establish the aggregation queues again.
Need to wait until driver re-establish all the station information before tear
down the aggregation queues, driver(at least iwlwifi driver) will reject the
stop aggregation queue request if station is not ready. But also need to make
sure the aggregation queues are tear down before waking up the queues, so
mac80211 will not sending frames with aggregation bit set.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"mac80211: fix skb buffering issue" still left a race
between enabling the hardware queues and the virtual
interface queues. In hindsight it's totally obvious
that enabling the netdev queues for a hardware queue
when the hardware queue is enabled is wrong, because
it could well possible that we can fill the hw queue
with packets we already have pending. Thus, we must
only enable the netdev queues once all the pending
packets have been processed and sent off to the device.
In testing, I haven't been able to trigger this race
condition, but it's clearly there, possibly only when
aggregation is being enabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An int urb is constructed but we fill it in with a bulk pipe type.
Commit f661c6f8c67bd55e93348f160d590ff9edf08904 implemented a pipe type
check when CONFIG_USB_DEBUG is enabled. The check failed for all the ar9170
usb transfers and the driver could not configure the wifi dongle.
This went unnoticed until now because most people don't have
CONFIG_USB_DEBUG enabled.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
IWL_RATE_COUNT is 13 and IWL_RATE_COUNT_LEGACY is 12.
IWL_RATE_COUNT_LEGACY is the right one here because iwl3945_rates
doesn't support 60M and also that's how "rates" is defined in
iwlcore_init_geos() from drivers/net/wireless/iwlwifi/iwl-core.c.
Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During backporting of a120e912eb51e347f36c71b60a1d13af74d30e83
("iwlwifi: sanity check before counting number of tfds can be free")
we forget one hunk, what make lot of messages "free more than
tfds_in_queue" show up in dmesg.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Tested-by: Adel Gadllah <adel.gadllah@gmail.com>
(picked from https://patchwork.kernel.org/patch/86722/) Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the cgroup freezer is used to freeze tasks we do not want to thaw
those tasks during resume. Currently we test the cgroup freezer
state of the resuming tasks to see if the cgroup is FROZEN. If so
then we don't thaw the task. However, the FREEZING state also indicates
that the task should remain frozen.
This also avoids a problem pointed out by Oren Ladaan: the freezer state
transition from FREEZING to FROZEN is updated lazily when userspace reads
or writes the freezer.state file in the cgroup filesystem. This means that
resume will thaw tasks in cgroups which should be in the FROZEN state if
there is no read/write of the freezer.state file to trigger this
transition before suspend.
NOTE: Another "simple" solution would be to always update the cgroup
freezer state during resume. However it's a bad choice for several reasons:
Updating the cgroup freezer state is somewhat expensive because it requires
walking all the tasks in the cgroup and checking if they are each frozen.
Worse, this could easily make resume run in N^2 time where N is the number
of tasks in the cgroup. Finally, updating the freezer state from this code
path requires trickier locking because of the way locks must be ordered.
Instead of updating the freezer state we rely on the fact that lazy
updates only manage the transition from FREEZING to FROZEN. We know that
a cgroup with the FREEZING state may actually be FROZEN so test for that
state too. This makes sense in the resume path even for partially-frozen
cgroups -- those that really are FREEZING but not FROZEN.
Reported-by: Oren Ladaan <orenl@cs.columbia.edu> Signed-off-by: Matt Helsley <matthltc@us.ibm.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We could be failing/stopping a connection due to libiscsi starting
recovery/cleanup, but the xmit path or scsi eh thread path
could be dropping the connection at the same time.
As a result the session->state gets set to failed instead of in
recovery. We end up not blocking the session
and so the replacement timeout never gets started and we only end up
failing the IO when scsi_softirq_done sees that the
cmd has been running for (cmd->allowed + 1) * rq->timeout secs.
We used to fail the IO right away so users are seeing a long
delay when using dm-multipath. This problem was added in
2.6.28.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For the boot, enable_mmu() is called from setup_arch() but we don't call
setup_arch() for any of the other cpus. So turn on the non-boot cpu's
mmu inside of start_secondary().
I noticed this bug on an SMP board when trying to map I/O memory
(smsc911x registers) into the kernel address space. Since the Address
Translation bit in MMUCR wasn't set, accessing the virtual address where
the smsc911x registers were supposedly mapped actually performed a
physical address access.
Signed-off-by: Matt Fleming <matt@console-pimps.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The radix-tree code requires it's users to serialize tag updates
against other updates to the tree. While XFS protects tag updates
against each other it does not serialize them against updates of the
tree contents, which can lead to tag corruption. Fix the inode
cache to always take pag_ici_lock in exclusive mode when updating
radix tree tags.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Patrick Schreurs <patrick@news-service.com> Tested-by: Patrick Schreurs <patrick@news-service.com> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The introduction of barriers to loop devices has created a new IO
order completion dependency that XFS does not handle. The loop
device implements barriers using fsync and so turns a log IO in the
XFS filesystem on the loop device into a data IO in the backing
filesystem. That is, the completion of log IOs in the loop
filesystem are now dependent on completion of data IO in the backing
filesystem.
This can cause deadlocks when a flush daemon issues a log force with
an inode locked because the IO completion of IO on the inode is
blocked by the inode lock. This in turn prevents further data IO
completion from occuring on all XFS filesystems on that CPU (due to
the shared nature of the completion queues). This then prevents the
log IO from completing because the log is waiting for data IO
completion as well.
The fix for this new completion order dependency issue is to make
the IO completion inode locking non-blocking. If the inode lock
can't be grabbed, simply requeue the IO completion back to the work
queue so that it can be processed later. This prevents the
completion queue from being blocked and allows data IO completion on
other inodes to proceed, hence avoiding completion order dependent
deadlocks.
Signed-off-by: Dave Chinner <david@fromorbit.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we hold onto reserved blocks when doing a remount,ro we end
up writing the blocks used count to disk that includes the reserved
blocks. Reserved blocks are not actually used, so this results in
the values in the superblock being incorrect.
Hence if we run xfs_check or xfs_repair -n while the filesystem is
mounted remount,ro we end up with an inconsistent filesystem being
reported. Also, running xfs_copy on the remount,ro filesystem will
result in an inconsistent image being generated.
To fix this, unreserve the blocks when doing the remount,ro, and
reserved them again on remount,rw. This way a remount,ro filesystem
will appear consistent on disk to all utilities.
Signed-off-by: Dave Chinner <david@fromorbit.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A "df" run on an NFS client of an exported XFS file system reports
the wrong information for "available" blocks. When a block quota is
enforced, the amount reported as free is limited by the quota, but
the amount reported available is not (and should be).
Reported-by: Guk-Bong, Kwon <gbkwon@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When swapping extents, we can corrupt inodes by swapping data forks
that are in incompatible formats. This is caused by the two indoes
having different fork offsets due to the presence of an attribute
fork on an attr2 filesystem. xfs_fsr tries to be smart about
setting the fork offset, but the trick it plays only works on attr1
(old fixed format attribute fork) filesystems.
Changing the way xfs_fsr sets up the attribute fork will prevent
this situation from ever occurring, so in the kernel code we can get
by with a preventative fix - check that the data fork in the
defragmented inode is in a format valid for the inode it is being
swapped into. This will lead to files that will silently and
potentially repeatedly fail defragmentation, so issue a warning to
the log when this particular failure occurs to let us know that
xfs_fsr needs updating/fixing.
To help identify how to improve xfs_fsr to avoid this issue, add
trace points for the inodes being swapped so that we can determine
why the swap was rejected and to confirm that the code is making the
right decisions and modifications when swapping forks.
A further complication is even when the swap is allowed to proceed
when the fork offset is different between the two inodes then value
for the maximum number of extents the data fork can hold can be
wrong. Make sure these are also set correctly after the swap occurs.
Signed-off-by: Dave Chinner <david@fromorbit.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When reclaiming stale inodes, we need to guarantee that inodes are
unpinned before returning with a "clean" status. If we don't we can
reclaim inodes that are pinned, leading to use after free in the
transaction subsystem as transactions complete.
Signed-off-by: Dave Chinner <david@fromorbit.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We cannot do direct inode reclaim without taking the flush lock to
ensure that we do not reclaim an inode under IO. We check the inode
is clean before doing direct reclaim, but this is not good enough
because the inode flush code marks the inode clean once it has
copied the in-core dirty state to the backing buffer.
It is the flush lock that determines whether the inode is still
under IO, even though it is marked clean, and the inode is still
required at IO completion so we can't reclaim it even though it is
clean in core. Hence the requirement that we need to take the flush
lock even on clean inodes because this guarantees that the inode
writeback IO has completed and it is safe to reclaim the inode.
With delayed write inode flushing, we could end up waiting a long
time on the flush lock even for a clean inode. The background
reclaim already handles this efficiently, so avoid all the problems
by killing the direct reclaim path altogether.
Signed-off-by: Dave Chinner <david@fromorbit.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The reclaim code will handle flushing of dirty inodes before reclaim
occurs, so avoid them when determining whether an inode is a
candidate for flushing to disk when walking the radix trees. This
is based on a test patch from Christoph Hellwig.
Signed-off-by: Dave Chinner <david@fromorbit.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make the inode tree reclaim walk exclusive to avoid races with
concurrent sync walkers and lookups. This is a version of a patch
posted by Christoph Hellwig that avoids all the code duplication.
Signed-off-by: Dave Chinner <david@fromorbit.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we search for and find a busy extent during allocation we
force the log out to ensure the extent free transaction is on
disk before the allocation transaction. The current implementation
has a subtle bug in it--it does not handle multiple overlapping
ranges.
That is, if we free lots of little extents into a single
contiguous extent, then allocate the contiguous extent, the busy
search code stops searching at the first extent it finds that
overlaps the allocated range. It then uses the commit LSN of the
transaction to force the log out to.
Unfortunately, the other busy ranges might have more recent
commit LSNs than the first busy extent that is found, and this
results in xfs_alloc_search_busy() returning before all the
extent free transactions are on disk for the range being
allocated. This can lead to potential metadata corruption or
stale data exposure after a crash because log replay won't replay
all the extent free transactions that cover the allocation range.
Modified-by: Alex Elder <aelder@sgi.com>
(Dropped the "found" argument from the xfs_alloc_busysearch trace
event.)
Signed-off-by: Dave Chinner <david@fromorbit.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because inodes remain in cache much longer than inode buffers do
under memory pressure, we can get the situation where we have
stale, dirty inodes being reclaimed but the backing storage has
been freed. Hence we should never, ever flush XFS_ISTALE inodes
to disk as there is no guarantee that the backing buffer is in
cache and still marked stale when the flush occurs.
Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We currently have some rather odd code in xfs_setattr for
updating the a/c/mtime timestamps:
- first we do a non-transaction update if all three are updated
together
- second we implicitly update the ctime for various changes
instead of relying on the ATTR_CTIME flag
- third we set the timestamps to the current time instead of the
arguments in the iattr structure in many cases.
This patch makes sure we update it in a consistent way:
- always transactional
- ctime is only updated if ATTR_CTIME is set or we do a size
update, which is a special case
- always to the times passed in from the caller instead of the
current time
The only non-size caller of xfs_setattr that doesn't come from
the VFS is updated to set ATTR_CTIME and pass in a valid ctime
value.
Reported-by: Eric Blake <ebb9@byu.net> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add an assert for inodes not added to the inode cache in xfs_ireclaim,
to make sure we're not going to introduce something like the
famous nfsd inode cache bug again.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Noticed that through glibc fallocate would return 28 rather than -1
and errno = 28 for ENOSPC. The xfs routines uses XFS_ERROR format
positive return error codes while the syscalls use negative return
codes. Fixup the two cases in xfs_vn_fallocate syscall to convert to
negative.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Reviewed-by: Eric Sandeen <sandeen@sandeen.net> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a journal record wraps at the physical end of the journal, it has to be
read in two parts in xlog_do_recovery_pass(): a read at the physical end and a
read at the physical beginning. If xlog_bread() has to re-align the first
read, the second read request does not take that re-alignment into account.
If the first read was re-aligned, the second read over-writes the end of the
data from the first read, effectively corrupting it. This can happen either
when reading the record header or reading the record data.
The first sanity check in xlog_recover_process_data() is to check for a valid
clientid, so that is the error reported.
Summary of fix:
If there was a first read at the physical end, XFS_BUF_PTR() returns where the
data was requested to begin. Conversely, because it is the result of
xlog_align(), offset indicates where the requested data for the first read
actually begins - whether or not xlog_bread() has re-aligned it.
Using offset as the base for the calculation of where to place the second read
data ensures that it will be correctly placed immediately following the data
from the first read instead of sometimes over-writing the end of it.
The attached patch has resolved the reported problem of occasional inability
to recover the journal (reporting "bad clientid").
Signed-off-by: Andy Poling <andy@realbig.com> Reviewed-by: Alex Elder <aelder@sgi.com> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When completing I/O requests we must not allow the memory allocator to
recurse into the filesystem, as we might deadlock on waiting for the
I/O completion otherwise. The only thing currently allocating normal
GFP_KERNEL memory is the allocation of the transaction structure for
the unwritten extent conversion. Add a memflags argument to
_xfs_trans_alloc to allow controlling the allocator behaviour.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Thomas Neumann <tneumann@users.sourceforge.net> Tested-by: Thomas Neumann <tneumann@users.sourceforge.net> Reviewed-by: Alex Elder <aelder@sgi.com> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When xfs_free_eofblocks is called from ->release the VM might already
hold the mmap_sem, but in the write path we take the iolock before
taking the mmap_sem in the generic write code.
Switch xfs_free_eofblocks to only trylock the iolock if called from
->release and skip trimming the prellocated blocks in that case.
We'll still free them later on the final iput.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Alex Elder <aelder@sgi.com> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently the reclaim code for the case where we don't reclaim the
final reclaim is overly complicated. We know that the inode is clean
but instead of just directly reclaiming the clean inode we go through
the whole process of marking the inode reclaimable just to directly
reclaim it from the calling context. Besides being overly complicated
this introduces a race where iget could recycle an inode between
marked reclaimable and actually being reclaimed leading to panics.
This patch gets rid of the existing reclaim path, and replaces it with
a simple call to xfs_ireclaim if the inode was clean. While we're at
it we also use the slightly more lax xfs_inode_clean check we'd use
later to determine if we need to flush the inode here.
Finally get rid of xfs_reclaim function and place the remaining small
bits of reclaim code directly into xfs_fs_destroy_inode.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Patrick Schreurs <patrick@news-service.com> Reported-by: Tommy van Leeuwen <tommy@news-service.com> Tested-by: Patrick Schreurs <patrick@news-service.com> Reviewed-by: Alex Elder <aelder@sgi.com> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace a BUG_ON with an error code in the event that the inode mapping
changes between calls to drm_open. This may happen for instance if udev
is loaded subsequent to the original opening of the device:
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
proc_oom_score(task) has a reference to task_struct, but that is all.
If this task was already released before we take tasklist_lock
- we can't use task->group_leader, it points to nowhere
- it is not safe to call badness() even if this task is
->group_leader, has_intersects_mems_allowed() assumes
it is safe to iterate over ->thread_group list.
- even worse, badness() can hit ->signal == NULL
Add the pid_alive() check to ensure __unhash_process() was not called.
Also, use "task" instead of task->group_leader. badness() should return
the same result for any sub-thread. Currently this is not true, but
this should be changed anyway.
When using the string representation of a random counter as part of the base
name, ensure that it is no longer than 4 bytes.
Since we are repeatedly decrementing the counter in a loop until we have found a
unique base name, the counter may wrap around zero; therefore, it is not enough
to mask its higher bits before entering the loop, this must be done inside the
loop.
Now the EDID property will be updated when the corresponding EDID can be
obtained from the external display device. But after the external device
is plugged-out, the EDID property is not updated. In such case we still
get the corresponding EDID property although it is already detected as
disconnected.
gfs2_lock() will skip locks on file which have mode set to 02666. This is a problem in cases where the mode of the file is changed after a process has obtained a lock on the file. Such a lock will be skipped and will result in a BUG in locks_remove_flock().
gfs2_lock() should skip the check for mandatory locks when unlocking a file.
On UV systems, the TSC is not synchronized across blades. The
sched_clock_cpu() function is returning values that can go
backwards (I've seen as much as 8 seconds) when switching
between cpus.
As each cpu comes up, early_init_intel() will currently set the
sched_clock_stable flag true. When mark_tsc_unstable() runs, it
clears the flag, but this only occurs once (the first time a cpu
comes up whose TSC is not synchronized with cpu 0). After this,
early_init_intel() will set the flag again as the next cpu comes
up.
Only set sched_clock_stable if tsc has not been marked unstable.
If no platform_data was givin to the device it's going to use it's default
platform data struct which has all fields initialized to zero. As a
result the driver is going to try to request gpio0 both as write protect
and card detect pin. Which of course will fail and makes the driver
unusable
Previously to the introduction of no_wprotect and no_detect the behavior
was to assume that if no platform data was given there is no write protect
or card detect pin. This patch restores that behavior.
block: Backport of various I/O topology fixes from 2.6.33 and 2.6.34
block: Backport of various I/O topology fixes from 2.6.33 and 2.6.34
The stacking code incorrectly scaled up the data offset in some cases
causing misaligned devices to report alignment. Rewrite the stacking
algorithm to remedy this.
The top device misalignment flag would not be set if the added bottom
device was already misaligned as opposed to causing a stacking failure.
Also massage the reporting so that an error is only returned if adding
the bottom device caused the misalignment. I.e. don't return an error
if the top is already flagged as misaligned.
lcm() was defined to take integer-sized arguments. The supplied
arguments are multiplied, however, causing us to overflow given
sufficiently large input. That in turn led to incorrect optimal I/O
size reporting in some cases. Switch lcm() over to unsigned long
similar to gcd() and move the function from blk-settings.c to lib.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The TKIP key update callback is called from the RX path, where the driver
mutex is already locked. This results in a circular locking bug.
Avoid this by removing the lock.
Johannes noted that there is a separate bug: The callback still breaks on SDIO
hardware, because SDIO hardware access needs to sleep, but we are not allowed
to sleep in the callback due to mac80211's RCU locking.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Reported-by: kecsa@kutfo.hit.bme.hu Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added very simple check that req buffer has enough space to
fit configuration parameters. Shall be enough to reject packets
with configuration size more than req buffer.
Crash trace below
[ 6069.659393] Unable to handle kernel paging request at virtual address 02000205
[ 6069.673034] Internal error: Oops: 805 [#1] PREEMPT
...
[ 6069.727172] PC is at l2cap_add_conf_opt+0x70/0xf0 [l2cap]
[ 6069.732604] LR is at l2cap_recv_frame+0x1350/0x2e78 [l2cap]
...
[ 6070.030303] Backtrace:
[ 6070.032806] [<bf1c2880>] (l2cap_add_conf_opt+0x0/0xf0 [l2cap]) from
[<bf1c6624>] (l2cap_recv_frame+0x1350/0x2e78 [l2cap])
[ 6070.043823] r8:dc5d3100 r7:df2a91d6 r6:00000001 r5:df2a8000 r4:00000200
[ 6070.050659] [<bf1c52d4>] (l2cap_recv_frame+0x0/0x2e78 [l2cap]) from
[<bf1c8408>] (l2cap_recv_acldata+0x2bc/0x350 [l2cap])
[ 6070.061798] [<bf1c814c>] (l2cap_recv_acldata+0x0/0x350 [l2cap]) from
[<bf0037a4>] (hci_rx_task+0x244/0x478 [bluetooth])
[ 6070.072631] r6:dc647700 r5:00000001 r4:df2ab740
[ 6070.077362] [<bf003560>] (hci_rx_task+0x0/0x478 [bluetooth]) from
[<c006b9fc>] (tasklet_action+0x78/0xd8)
[ 6070.087005] [<c006b984>] (tasklet_action+0x0/0xd8) from [<c006c160>]
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com> Acked-by: Gustavo F. Padovan <gustavo@padovan.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>