Linus Torvalds [Sat, 18 Aug 2012 23:20:05 +0000 (16:20 -0700)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"The largest thing in this set of changes is bringing back some of the
ARMv3 code to fix a compile problem noticed on RiscPC, which we still
support, even though we only support ARMv4 there.
(The reason is that the system bus doesn't support ARMv4 half-word
accesses, so we need the ARMv3 library code for this platform.)
The rest are all quite minor fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7490/1: Drop duplicate select for GENERIC_IRQ_PROBE
ARM: Bring back ARMv3 IO and user access code
ARM: 7489/1: errata: fix workaround for erratum #720789 on UP systems
ARM: 7488/1: mm: use 5 bits for swapfile type encoding
ARM: 7487/1: mm: avoid setting nG bit for user mappings that aren't present
ARM: 7486/1: sched_clock: update epoch_cyc on resume
ARM: 7484/1: Don't enable GENERIC_LOCKBREAK with ticket spinlocks
ARM: 7483/1: vfp: only advertise VFPv4 in hwcaps if CONFIG_VFPv3 is enabled
ARM: 7482/1: topology: fix section mismatch warning for init_cpu_topology
Linus Torvalds [Sat, 18 Aug 2012 21:39:19 +0000 (14:39 -0700)]
Merge tag 'pm-for-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
- Fixes for three obscure problems in the runtime PM core code found
recently.
- Two fixes for the new "coupled" cpuidle code from Colin Cross and Jon
Medhurst.
- intel_idle driver fix from Konrad Rzeszutek Wilk.
* tag 'pm-for-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_idle: Check cpu_idle_get_driver() for NULL before dereferencing it.
cpuidle: Prevent null pointer dereference in cpuidle_coupled_cpu_notify
cpuidle: coupled: fix sleeping while atomic in cpu notifier
PM / Runtime: Check device PM QoS setting before "no callbacks" check
PM / Runtime: Clear power.deferred_resume on success in rpm_suspend()
PM / Runtime: Fix rpm_resume() return value for power.no_callbacks set
Linus Torvalds [Sat, 18 Aug 2012 17:02:17 +0000 (10:02 -0700)]
Merge branch 'vfs-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull vfs fixes from Miklos Szeredi.
This mainly fixes some confusion about whether the open 'mode' variable
passed around should contain the full file type (S_IFREG etc)
information or just the permission mode. In particular, the lack of
proper file type information had confused fuse.
* 'vfs-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
vfs: fix propagation of atomic_open create error on negative dentry
fuse: check create mode in atomic open
vfs: pass right create mode to may_o_create()
vfs: atomic_open(): fix create mode usage
vfs: canonicalize create mode in build_open_flags()
Sven Schnelle [Fri, 17 Aug 2012 19:43:43 +0000 (21:43 +0200)]
USB: CDC ACM: Fix NULL pointer dereference
If a device specifies zero endpoints in its interface descriptor,
the kernel oopses in acm_probe(). Even though that's clearly an
invalid descriptor, we should test wether we have all endpoints.
This is especially bad as this oops can be triggered by just
plugging a USB device in.
USB: emi62: remove __devinit* from the struct usb_device_id table
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Reported-by: Bjørn Mork <bjorn@mork.no> Cc: stable <stable@vger.kernel.org> CC: Paul Gortmaker <paul.gortmaker@windriver.com> CC: Andrew Morton <akpm@linux-foundation.org> CC: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: winbond: remove __devinit* from the struct usb_device_id table
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
USB: vt6656: remove __devinit* from the struct usb_device_id table
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Reported-by: Bjørn Mork <bjorn@mork.no> Cc: stable <stable@vger.kernel.org> CC: Forest Bond <forest@alittletooquiet.net> CC: Marcos Paulo de Souza <marcos.souza.org@gmail.com> CC: "David S. Miller" <davem@davemloft.net> CC: Jesper Juhl <jj@chaosbits.net> CC: Jiri Pirko <jpirko@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: rtl8187: remove __devinit* from the struct usb_device_id table
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
USB: p54usb: remove __devinit* from the struct usb_device_id table
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
USB: spca506: remove __devinit* from the struct usb_device_id table
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
USB: jl2005bcd: remove __devinit* from the struct usb_device_id table
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
USB: smsusb: remove __devinit* from the struct usb_device_id table
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Linus Torvalds [Sat, 18 Aug 2012 00:47:32 +0000 (17:47 -0700)]
Merge tag 'md-3.6-fixes' of git://neil.brown.name/md
Pull md fixes from NeilBrown:
"2 fixes for md, tagged for -stable"
* tag 'md-3.6-fixes' of git://neil.brown.name/md:
md/raid10: fix problem with on-stack allocation of r10bio structure.
md: Don't truncate size at 4TB for RAID0 and Linear
NeilBrown [Fri, 17 Aug 2012 23:51:42 +0000 (09:51 +1000)]
md/raid10: fix problem with on-stack allocation of r10bio structure.
A 'struct r10bio' has an array of per-copy information at the end.
This array is declared with size [0] and r10bio_pool_alloc allocates
enough extra space to store the per-copy information depending on the
number of copies needed.
So declaring a 'struct r10bio on the stack isn't going to work. It
won't allocate enough space, and memory corruption will ensue.
So in the two places where this is done, declare a sufficiently large
structure and use that instead.
The two call-sites of this bug were introduced in 3.4 and 3.5
so this is suitable for both those kernels. The patch will have to
be modified for 3.4 as it only has one bug.
Cc: stable@vger.kernel.org Reported-by: Ivan Vasilyev <ivan.vasilyev@gmail.com> Tested-by: Ivan Vasilyev <ivan.vasilyev@gmail.com> Signed-off-by: NeilBrown <neilb@suse.de>
Linus Torvalds [Fri, 17 Aug 2012 18:45:58 +0000 (11:45 -0700)]
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma fixes from Roland Dreier:
"Grab bag of InfiniBand/RDMA fixes:
- IPoIB fixes for regressions introduced by path database conversion
- mlx4 fixes for bugs with large memory systems and regressions from
SR-IOV patches
- RDMA CM fix for passing bad event up to userspace
- Other minor fixes"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Check iboe netdev pointer before dereferencing it
mlx4_core: Clean up buddy bitmap allocation
mlx4_core: Fix integer overflow issues around MTT table
mlx4_core: Allow large mlx4_buddy bitmaps
IB/srp: Fix a race condition
IB/qib: Fix error return code in qib_init_7322_variables()
IB: Fix typos in infiniband drivers
IB/ipoib: Fix RCU pointer dereference of wrong object
IB/ipoib: Add missing locking when CM object is deleted
RDMA/ucma.c: Fix for events with wrong context on iWARP
RDMA/ocrdma: Don't call vlan_dev_real_dev() for non-VLAN netdevs
IB/mlx4: Fix possible deadlock on sm_lock spinlock
intel_idle: Check cpu_idle_get_driver() for NULL before dereferencing it.
If the machine is booted without any cpu_idle driver set
(b/c disable_cpuidle() has been called) we should follow
other users of cpu_idle API and check the return value
for NULL before using it.
Reported-and-tested-by: Mark van Dijk <mark@internecto.net> Suggested-by: Jan Beulich <JBeulich@suse.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
cpuidle: Prevent null pointer dereference in cpuidle_coupled_cpu_notify
When a kernel is built to support multiple hardware types it's possible
that CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED is set but the hardware the
kernel is run on doesn't support cpuidle and therefore doesn't load a
driver for it. In this case, when the system is shut down,
cpuidle_coupled_cpu_notify() gets called with cpuidle_devices set to
NULL. There are quite possibly other circumstances where this
situation can also occur and we should check for it.
Signed-off-by: Jon Medhurst <tixy@linaro.org> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Colin Cross [Wed, 15 Aug 2012 20:10:50 +0000 (22:10 +0200)]
cpuidle: coupled: fix sleeping while atomic in cpu notifier
The cpu hotplug notifier gets called in both atomic and non-atomic
contexts, it is not always safe to lock a mutex. Filter out all events
except the six necessary ones, which are all sleepable, before taking
the mutex.
Signed-off-by: Colin Cross <ccross@android.com> Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
PM / Runtime: Check device PM QoS setting before "no callbacks" check
If __dev_pm_qos_read_value(dev) returns a negative value,
rpm_suspend() should return -EPERM for dev even if its
power.no_callbacks flag is set. For this to happen, the device's
power.no_callbacks flag has to be checked after the PM QoS check,
so move the PM QoS check to rpm_check_suspend_allowed() (this will
make it cover idle notifications as well as runtime suspend too).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable@vger.kernel.org
PM / Runtime: Clear power.deferred_resume on success in rpm_suspend()
The power.deferred_resume can only be set if the runtime PM status
of device is RPM_SUSPENDING and it should be cleared after its
status has been changed, regardless of whether or not the runtime
suspend has been successful. However, it only is cleared on
suspend failure, while it may remain set on successful suspend and
is happily leaked to rpm_resume() executed in that case.
That shouldn't happen, so if power.deferred_resume is set in
rpm_suspend() after the status has been changed to RPM_SUSPENDED,
clear it before calling rpm_resume(). Then, it doesn't need to be
cleared before changing the status to RPM_SUSPENDING any more,
because it's always cleared after the status has been changed to
either RPM_SUSPENDED (on success) or RPM_ACTIVE (on failure).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable@vger.kernel.org
PM / Runtime: Fix rpm_resume() return value for power.no_callbacks set
For devices whose power.no_callbacks flag is set, rpm_resume()
should return 1 if the device's parent is already active, so that
the callers of pm_runtime_get() don't think that they have to wait
for the device to resume (asynchronously) in that case (the core
won't queue up an asynchronous resume in that case, so there's
nothing to wait for anyway).
Modify the code accordingly (and make sure that an idle notification
will be queued up on success, even if 1 is to be returned).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable@vger.kernel.org
Linus Torvalds [Fri, 17 Aug 2012 17:17:03 +0000 (10:17 -0700)]
Merge tag 'staging-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg Kroah-Hartman:
"Here are some staging driver fixes (and iio driver fixes, they get
lumped in with the staging stuff due to dependancies) for your 3.6-rc3
tree.
Nothing major, just a bunch of fixes that people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (26 commits)
iio: lm3533-als: Fix build warnings
staging:iio:ad7780: Mark channels as unsigned
staging:iio:ad7192: Report offset and scale for temperature channel
staging:iio:ad7192: Report channel offset
staging:iio:ad7192: Mark channels as unsigned
staging:iio:ad7192: Fix setting ACX
staging:iio:ad7192: Add missing break in switch statement
staging:iio:ad7793: Fix internal reference value
staging:iio:ad7793: Follow new IIO naming spec
staging:iio:ad7793: Fix temperature scale and offset
staging:iio:ad7793: Report channel offset
staging:iio:ad7793: Mark channels as unsigned
staging:iio:ad7793: Add missing break in switch statement
iio/adjd_s311: Fix potential memory leak in adjd_s311_update_scan_mode()
iio: frequency: ADF4350: Fix potential reference div factor overflow.
iio: staging: ad7298_ring: Fix maybe-uninitialized warning
staging: comedi: usbduxfast: Declare MODULE_FIRMWARE usage
staging: comedi: usbdux: Declare MODULE_FIRMWARE usage
staging: comedi: usbduxsigma: Declare MODULE_FIRMWARE usage
staging: csr: add INET dependancy
...
Linus Torvalds [Fri, 17 Aug 2012 17:16:30 +0000 (10:16 -0700)]
Merge tag 'driver-core-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg Kroah-Hartman:
"Here are two tiny patches, one fixing a dynamic debug problem that the
printk rework turned up, and the other one fixing an extcon problem
that people reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
extcon: extcon_gpio: Replace gpio_request_one by devm_gpio_request_one
drivers-core: make structured logging play nice with dynamic-debug
Linus Torvalds [Fri, 17 Aug 2012 17:15:57 +0000 (10:15 -0700)]
Merge tag 'char-misc-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull Char / Misc driver fixes from Greg Kroah-Hartman:
"Here are some small misc and w1 driver fixes for 3.6-rc3. Nothing
major, just some some bugfixes and a new device id for a w1 driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'char-misc-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
1-Wire: Add support for the maxim ds1825 temperature sensor
ti-st: Fix check for pdata->chip_awake function pointer
mei: add mei_quirk_probe function
mei: fix device stall after wd is stopped
Linus Torvalds [Fri, 17 Aug 2012 17:14:53 +0000 (10:14 -0700)]
Merge tag 'usb-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here are a number of small USB patches for 3.6-rc3.
The "large" one is just a number of device id updates to the option
driver, done by the manufacturer, properly fixing up the device ids
based on shipping devices.
Other than that, some gadget driver fixes, the obligitary XHCI
patches, and some other device ids and bugs fixed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
USB: qcserial: fix port handling on Gobi 1K and 2K+
USB: serial: Fix mos7840 timeout
USB: option: add ZTE K5006-Z
usb: gadget: u_ether: fix kworker 100% CPU issue with still used interfaces in eth_stop
usb: host: tegra: fix warning messages in ehci_remove
usb: host: mips: sead3: Update for EHCI register structure.
usb: renesas_usbhs: fixup resume method for autonomy mode
usb: renesas_usbhs: mod_host: add missing .bus_suspend/resume
update MAINTAINERS for Oliver Neukum
usb: usb_wwan: resume/suspend can be called after port is gone
usb: serial: prevent suspend/resume from racing against probe/remove
usb: usb_wwan: replace release and disconnect with a port_remove hook
usb: serial: mos7840: Fixup mos7840_chars_in_buffer()
USB: isp1362-hcd.c: usb message always saved in case of underrun
OMAP: USB : Fix the EHCI enumeration and core retention issue
usb: chipidea: fix and improve dependencies if usb host or gadget support is built as module
USB: support the new interfaces of Huawei Data Card devices in option driver
USB: ftdi_sio: Add VID/PID for Kondo Serial USB
xhci: Switch PPT ports to EHCI on shutdown.
xhci: Fix bug after deq ptr set to link TRB.
...
Linus Torvalds [Fri, 17 Aug 2012 15:04:47 +0000 (08:04 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bug fixes from Ted Ts'o:
"The following are all bug fixes and regressions. The most notable are
the ones which cause problems for ext4 on RAID --- a performance
problem when mounting very large filesystems, and a kernel OOPS when
doing an rm -rf on large directory hierarchies on fast devices."
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix kernel BUG on large-scale rm -rf commands
ext4: fix long mount times on very big file systems
ext4: don't call ext4_error while block group is locked
ext4: avoid kmemcheck complaint from reading uninitialized memory
ext4: make sure the journal sb is written in ext4_clear_journal_err()
powerpc/mpc85xx: Add new ext fields to Integrated FLash Controller
Freescale's Integrated Flash controller(IFC) v1.1.0 supports 40 bit
address bus width.
In case more than 32 bit address is used, the EXT registers should be set.
Add support of ext registers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ian Kent [Fri, 17 Aug 2012 03:09:04 +0000 (11:09 +0800)]
autofs4 - fix expire check
In some cases when an autofs indirect mount is contained in a file
system that is marked as shared (such as when systemd does the
equivalent of "mount --make-rshared /" early in the boot), mounts
stop expiring.
When this happens the first expiry check on a mountpoint dentry in
autofs_expire_indirect() sees a mountpoint dentry with a higher
than minimal reference count. Consequently the dentry is condidered
busy and the actual expiry check is never done.
This particular check was originally meant as an optimisation to
detect a path walk in progress but with the addition of rcu-walk
it can be ineffective anyway.
Removing the test allows automounts to expire again since the
actual expire check doesn't rely on the dentry reference count.
Signed-off-by: Ian Kent <raven@themaw.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Theodore Ts'o [Fri, 17 Aug 2012 12:54:52 +0000 (08:54 -0400)]
ext4: fix kernel BUG on large-scale rm -rf commands
Commit 968dee7722: "ext4: fix hole punch failure when depth is greater
than 0" introduced a regression in v3.5.1/v3.6-rc1 which caused kernel
crashes when users ran run "rm -rf" on large directory hierarchy on
ext4 filesystems on RAID devices:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000028
The problem in commit 968dee7722 was that caused the variable 'i' to
be left uninitialized if the truncate required more space than was
available in the journal. This resulted in the function
ext4_ext_truncate_extend_restart() returning -EAGAIN, which caused
ext4_ext_remove_space() to restart the truncate operation after
starting a new jbd2 handle.
Theodore Ts'o [Thu, 16 Aug 2012 15:59:04 +0000 (11:59 -0400)]
ext4: fix long mount times on very big file systems
Commit 8aeb00ff85a: "ext4: fix overhead calculation used by
ext4_statfs()" introduced a O(n**2) calculation which makes very large
file systems take forever to mount. Fix this with an optimization for
non-bigalloc file systems. (For bigalloc file systems the overhead
needs to be set in the the superblock.)
Theodore Ts'o [Fri, 10 Aug 2012 17:57:52 +0000 (13:57 -0400)]
ext4: don't call ext4_error while block group is locked
While in ext4_validate_block_bitmap(), if an block allocation bitmap
is found to be invalid, we call ext4_error() while the block group is
still locked. This causes ext4_commit_super() to call a function
which might sleep while in an atomic context.
There's no need to keep the block group locked at this point, so hoist
the ext4_error() call up to ext4_validate_block_bitmap() and release
the block group spinlock before calling ext4_error().
Kees Cook [Wed, 15 Aug 2012 18:41:55 +0000 (11:41 -0700)]
Yama: access task_struct->comm directly
The core ptrace access checking routine holds a task lock, and when
reporting a failure, Yama takes a separate task lock. To avoid a
potential deadlock with two ptracers taking the opposite locks, do not
use get_task_comm() and just use ->comm directly since accuracy is not
important for the report.
Ralf Baechle [Fri, 17 Aug 2012 08:22:35 +0000 (10:22 +0200)]
MIPS: Add support for SECCOMP_FILTER.
Enable tasks to build secure computing environments defined in terms
of Berkeley Packet Filter programs which implement task-defined system
call filtering polices.
See Documentation/prctl/seccomp_filter.txt for details.
John Crispin [Tue, 24 Jul 2012 06:29:46 +0000 (08:29 +0200)]
MIPS: Lantiq: Add helper to set PCI clock delay
The PCI core has a register that allows us to set the nanosecond delay of the
PCI clock lane. This patch adds a helper function to allow setting this value.
Al Cooper [Fri, 13 Jul 2012 20:44:54 +0000 (16:44 -0400)]
MIPS: perf: Add perf functionality for BMIPS5000
Add hardware performance counter support to kernel "perf" code for
BMIPS5000. The BMIPS5000 performance counters are similar to MIPS
MTI cores, so the changes were mostly made in perf_event_mipsxx.c
which is typically for MTI cores.
Signed-off-by: Al Cooper <alcooperx@gmail.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4109/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Al Cooper [Fri, 13 Jul 2012 20:44:53 +0000 (16:44 -0400)]
MIPS: perf: Split the Kconfig option CONFIG_MIPS_MT_SMP
Split the Kconfig option CONFIG_MIPS_MT_SMP into CONFIG_MIPS_MT_SMP
and CONFIG_MIPS_PERF_SHARED_TC_COUNTERS so some of the code used
for performance counters that are shared between threads can be used
for MIPS cores that are not MT_SMP.
Signed-off-by: Al Cooper <alcooperx@gmail.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4108/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Al Cooper [Fri, 13 Jul 2012 20:44:52 +0000 (16:44 -0400)]
MIPS: perf: Remove unnecessary #ifdef
The #ifdef for CONFIG_HW_PERF_EVENTS is not needed because the
Makefile will only compile the module if this config option is set.
This means that the code under #else would never be compiled. This
may have been done to leave the original broken code around for
reference, but the FIXME comment above the code already shows the
broken code.
Signed-off-by: Al Cooper <alcooperx@gmail.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4107/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Al Cooper [Fri, 13 Jul 2012 20:44:51 +0000 (16:44 -0400)]
MIPS: perf: Add cpu feature bit for PCI (performance counter interrupt)
The PCI (Program Counter Interrupt) bit in the "cause" register
is mandatory for MIPS32R2 cores, but has also been added to some R1
cores (BMIPS5000). This change adds a cpu feature bit to make it
easier to check for and use this feature.
Signed-off-by: Al Cooper <alcooperx@gmail.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4106/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Al Cooper [Fri, 13 Jul 2012 20:44:50 +0000 (16:44 -0400)]
MIPS: perf: Change the "mips_perf_event" table unsupported indicator.
Change the indicator from 0xffffffff in the "event_id" member to
zero in the "cntr_mask" member. This removes the need to initialize
entries that are unsupported. This also solves a problem where the
number of entries in the table was increased based on a globel enum
used for all platforms, but the new unsupported entries were not added
for mips. This was leaving new table entries of all zeros that we not
marked UNSUPPORTED.
Signed-off-by: Al Cooper <alcooperx@gmail.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4110/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Tue, 14 Aug 2012 18:08:01 +0000 (11:08 -0700)]
MIPS: Align swapper_pg_dir to 64K for better TLB Refill code.
We can save an instruction in the TLB Refill path for kernel mappings
by aligning swapper_pg_dir on a 64K boundary. The address of
swapper_pg_dir can be generated with a single LUI instead of
LUI/{D}ADDUI.
The alignment of __init_end is bumped up to 64K so there are no holes
between it and swapper_pg_dir, which is placed at the very beginning
of .bss.
The alignment of invalid_pmd_table and invalid_pte_table can be
relaxed to PAGE_SIZE. We do this by using __page_aligned_bss, which
has the added benefit of eliminating alignment holes in .bss.
Joshua Kinard [Mon, 25 Jun 2012 01:01:34 +0000 (21:01 -0400)]
Improve atomic.h robustness
I've maintained this patch, originally from Thiemo Seufer in 2004, for a
really long time, but I think it's time for it to get a look at for
possible inclusion. I have had no problems with it across various SGI
systems over the years.
To quote the post here:
http://www.linux-mips.org/archives/linux-mips/2004-12/msg00000.html
"the atomic functions use so far memory references for the inline
assembler to access the semaphore. This can lead to additional
instructions in the ll/sc loop, because newer compilers don't
expand the memory reference any more but leave it to the assembler.
The appended patch uses registers instead, and makes the ll/sc
arguments more explicit. In some cases it will lead also to better
register scheduling because the register isn't bound to an output
any more."
Gabor Juhos [Tue, 14 Aug 2012 19:12:21 +0000 (21:12 +0200)]
MIPS: ath79: don't hardcode the unavailability of the DSP ASE
The ath79 platform code allows to run a single kernel image on various
SoCs which are based on the 24Kc and 74Kc cores. The current code
explicitely disables the DSP ASE, but that is available in the 74Kc core.
Remove the override in order to let the kernel to detect the availability
of the DSP ASE at runtime.
Jayachandran C [Tue, 14 Aug 2012 13:26:13 +0000 (18:56 +0530)]
MIPS: Synchronize MIPS count one CPU at a time
The current implementation of synchronise_count_{master,slave} blocks
slave CPUs in early boot until all of them come up. This no longer
works because blocking a CPU with interrupts off after notifying the
CPU to be online causes problems with the current kernel.
Specifically, after the workqueue changes
(commit a08489c569dc1 "Pull workqueue changes from Tejun Heo")
the CPU_ONLINE notification callback workqueue_cpu_up_callback()
will hang on wait_for_completion(&idle_rebind.done), if the slave
CPUs are blocked for synchronize_count_slave().
The changes are to update synchronize_count_{master,slave}() to handle
one CPU at a time and to call synchronise_count_master() in __cpu_up()
so that the CPU_ONLINE notification goes out only after the COP0 COUNT
register is synchronized.
[ralf@linux-mips.org: This matter only to those few platforms which are
using the cp0 counter as their clocksource which are XLP, XLR and MIPS'
CMP solution.]
Florian Fainelli [Mon, 18 Jun 2012 10:07:51 +0000 (12:07 +0200)]
MIPS: BCM63xx: Fix SPI message control register handling for BCM6338/6348.
BCM6338 and BCM6348 have a message control register width of 8 bits, instead
of 16-bits like what the SPI driver assumes right now. Also the SPI message
type shift value of 14 is actually 6 for these SoCs.
This resulted in transmit FIFO corruption because we were writing 16-bits
to an 8-bits wide register, thus spanning on the first byte of the transmit
FIFO, which had already been filed in bcm63xx_spi_fill_txrx_fifo().
Fix this by passing the message control register width and message type
shift through platform data back to the SPI driver so that it can use
it properly.
Ralf Baechle [Mon, 13 Aug 2012 22:34:18 +0000 (00:34 +0200)]
MIPS: Module: Deal with malformed HI16/LO16 relocation sequences.
In case a series of R_MIPS_HI16 relocations was not followed by an
R_MIPS_LO16 relocation we were leaking the hi16 relocation chain.
Handle that error and return an error.
Ralf Baechle [Wed, 8 Aug 2012 14:59:43 +0000 (16:59 +0200)]
MIPS: Fix race condition in module relocation code.
The relocation code was essentially taken from the 2.4 modutils which
perform relocation in userspace. In 2.6 relocation of multiple modules
may be performed in parallel by the in-kernel loader so the global
variable mips_hi16_list won't fly anymore. Fix race by moving it into
mod_arch_specific.
[ralf@linux-mips.org: folded in Tony's followup fix. Thanks Tony!]
Bruno Randolf [Thu, 12 Jul 2012 20:54:05 +0000 (21:54 +0100)]
MIPS: MTX-1: Add udelay to mtx1_pci_idsel
Without this udelay(1) PCI idsel does not work correctly on the
"singleboard" (T-Mobile Surfbox) for the MiniPCI device. The result is
that PCI configuration fails and the MiniPCI card is not detected
correctly. Instead of
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
pci 0000:00:03.0: BAR 0: assigned [mem 0x40000000-0x4000ffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40010000-0x40010fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40011000-0x40011fff]
We see only the CardBus device:
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40000000-0x40000fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40001000-0x40001fff]
Later the device driver shows this error:
ath5k 0000:00:03.0: cannot remap PCI memory region
ath5k: probe of 0000:00:03.0 failed with error -5
I assume that the logic chip which usually supresses the signal to the CardBus
card has some settling time and without the delay it would still let the
Cardbus interfere with the response from the MiniPCI card.
What I cannot explain is why this behaviour shows up now and not in earlier
kernel versions before. Maybe older PCI code was slower?
projects / karo-tx-linux.git / log