Duson Lin [Thu, 3 Sep 2015 16:46:45 +0000 (09:46 -0700)]
Input: elan_i2c - use iap_version to get firmware information
When driver is in IAP mode ic_type query may return 0xff. However
iap_version will always be valid, so let's use it to determine parameters
of the firmware that the controller is supposed to accept.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver is a platform driver and not a I2C driver so its modalias
should be exported with MODULE_DEVICE_TABLE(platform,...) instead of
MODULE_DEVICE_TABLE(i2c,...).
Also, remove the unnecessary MODULE_ALIAS("platform:max8997-haptic")
now that the correct module alias is created.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stefan Assmann [Wed, 26 Aug 2015 20:11:49 +0000 (13:11 -0700)]
Input: psmouse - add small delay for IBM trackpoint pass-through mode
There are trackpoint devices that fail to respond to the PS2 command
PSMOUSE_CMD_GETID if immediately queried after the parent device is
deactivated. Add a small delay for the hardware to get in a sane state
before sending any PS2 commands.
One example of such a system is:
Lenovo ThinkPad X120e, model 30515QG
synaptics: Touchpad model: 1, fw: 8.0, id: 0x1e2b1, caps: 0xd001a3/0x940300/0x121c00, board id: 1811, fw id: 797391
Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dan Carpenter [Fri, 21 Aug 2015 16:29:50 +0000 (09:29 -0700)]
Input: sentelic - silence some underflow warnings
I have a static checker that complains when we check for an upper bound
but don't have a corresponding check for a lower bound. With this code,
the upper bound check seems not really required, so it is not a bug to
leave the lower bound check out as well. But let's silence the warning
by making these variables unsigned.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ChromeOS EC keyboard driver config depends on CROS_EC_PROTO but
MFD_CROS_EC selects CROS_EC_PROTO instead. Mixing select and depends
on is bad practice as it may lead to circular Kconfig dependencies.
Since the platform device that is matched with the keyboard driver
is registered by the ChromeOS EC mfd driver, KEYBOARD_CROS_EC really
should depend on MFD_CROS_EC. And because this config option selects
CROS_EC_PROTO, that dependency is met as well. So make the driver
to depend on MFD_CROS_EC instead of CROS_EC_PROTO.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry Torokhov [Wed, 5 Aug 2015 19:01:30 +0000 (12:01 -0700)]
Input: elan_i2c - enable asynchronous probing
It takes a bit of time to go through controller power up sequence and
initialization. To not stall the overall boot progress let's probe the
controller asynchronously, given that userspace is usually prepared for
hot-plugging of input devices and thus does not rely on particular
ordering.
It takes a bit of time to go through controller power up sequence and
initialization. To not stall the overall boot progress let's probe the
controller asynchronously, given that userspace is usually prepared for
hot-plugging of input devices and thus does not rely on particular
ordering.
Elan touchscreen controllers use two power supplies, vcc33 and vccio,
and we need to enable them before trying to access the device. On X86
firmware usually does this, but on ARM it is usually left to the kernel.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org> Reviewed-by: Benson Leung <bleung@chromium.org> Reviewed-by: Scott Liu <scott.liu@emc.com.tw> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry Torokhov [Fri, 7 Aug 2015 02:15:30 +0000 (19:15 -0700)]
Input: do not emit unneeded EV_SYN when suspending
Do not emit EV_SYN/SYN_REPORT on suspend if there were no keys that are
still pressed as we are suspending the device (and in all other cases when
input core is forcibly releasing keys via input_dev_release_keys() call).
James Chen [Mon, 20 Jul 2015 18:16:36 +0000 (11:16 -0700)]
Input: elants_i2c - disable idle mode before updating firmware
If the device is in idle mode and is in the middle of a scan it may not
have a chance to react to the reset and then IAP commands within required
time interval and firmware update may fail. Let's bring the device out of
idle mode before attempting to reset it so that the scan period is smaller
and thus it can react to the command quicker.
Signed-off-by: James Chen <james.chen@emc.com.tw> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Nick Dyer [Tue, 4 Aug 2015 23:57:40 +0000 (16:57 -0700)]
Input: atmel_mxt_ts - initialise input slots with INPUT_MT_DIRECT
This indicates the device coordinates should be directly mapped to screen.
This is valid since scaling/flipping/rotation should be done by configuring
the MXT device.
It also flags to Android using INPUT_PROP_DIRECT that the device should be
treated as a touch screen by default, and removes the necessity for a
default IDC file.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Nick Dyer [Tue, 4 Aug 2015 23:57:25 +0000 (16:57 -0700)]
Input: atmel_mxt_ts - disable interrupt for 50ms after reset
The CHG/interrupt line is momentarily set (approximately 100 ms) as an
input after power-up or reset for diagnostic purposes. This may cause
spurious interrupts, so disable interrupt handler during this period.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pan Xinhui [Tue, 4 Aug 2015 23:53:04 +0000 (16:53 -0700)]
Input: atmel_mxt_ts - suspend/resume causes panic if input_dev fails to init
input_dev may be NULL if mxt_initialize_input_device fails. But pm ops is
still available and suspend/resume assume
input_dev is not NULL. To fix this issue, we add a check if (!input_dev).
Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com> Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Nick Dyer [Tue, 4 Aug 2015 23:36:29 +0000 (16:36 -0700)]
Input: atmel_mxt_ts - use deep sleep mode when stopped
The hardcoded 0x83 CTRL setting overrides other settings in that byte,
enabling extra reporting that may not be useful on a particular platform.
Implement improved suspend mechanism via deep sleep. By writing zero to
both the active and idle cycle times the maXTouch device can be put into a
deep sleep mode, using minimal power. It is necessary to issue a calibrate
command after the chip has spent any time in deep sleep, however a soft
reset is unnecessary.
Use the old method on Chromebook Pixel via platform data option.
This patch also deals with the situation where the power configuration is
zero on probe, which would mean that the device never wakes up to execute
commands.
After a config download, the T7 power configuration may have changed so it
is necessary to re-read it.
Input: Allow compile test of GPIO consumers if !GPIOLIB
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Dirk Behme [Mon, 3 Aug 2015 20:03:09 +0000 (13:03 -0700)]
Input: zforce - make the interrupt GPIO optional
Add support for hardware which uses an I2C Serializer / Deserializer
(SerDes) to communicate with the zFroce touch driver. In this case the
SerDes will be configured as an interrupt controller and the zForce driver
will have no access to poll the GPIO line.
To support this, we add two dedicated new GPIOs in the device tree:
reset-gpios and irq-gpios, with the irq-gpios being optional.
To not break the existing device trees, the index based 'gpios' entries
are still supported, but marked as deprecated.
With this, if the interrupt GPIO is available, either via the old or new
device tree style, the while loop will read and handle the packets as long
as the GPIO indicates that the interrupt is asserted (existing, unchanged
driver behavior).
If the interrupt GPIO isn't available, i.e. not configured via the new
device tree style, we are falling back to one read per ISR invocation
(new behavior to support the SerDes).
Note that the gpiod functions help to handle the optional GPIO:
devm_gpiod_get_index_optional() will return NULL in case the interrupt
GPIO isn't available. And gpiod_get_value_cansleep() does cover this, too,
by returning 0 in this case.
Dudley Du [Thu, 30 Jul 2015 18:26:39 +0000 (11:26 -0700)]
Input: cyapa - do not try to enable proximity reporting on older devices
Avoid the driver generate warning message when the cyapa driver working
with the old Gen5 trackpad device which does not support the proximity
function. Those old Gen5 trackpad device all have the platform version
less than 2.
Signed-off-by: Dudley Du <dudl@cypress.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Input: touchscreen - export OF module alias information
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.
In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.
And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.
To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Input: export I2C module alias information in missing drivers
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The GPIOD API can be used from boardcode, so that the DT check can be
removed. To avoid breaking existing boardcode, _optional() variant has been
chosen. For completely removing the DT check, the regulator has also been
made optional, so that it could be supplied from boardcode.
As a side-effect the patch fixes the after-probe reset GPIO state, so that
the device is not kept in reset state.
Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Input: tsc2005 - improve readability of register defines
Improve defines for first control byte by removing 0x00 prefix (the defines
are for 8 bit values and not for 16 bit values) and expose register
structure by exposing the shift.
Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dudley Du [Tue, 21 Jul 2015 00:09:59 +0000 (17:09 -0700)]
Input: cyapa - fully support runtime suspend power management
Fix the the runtime suspend power management not working issue when system
starts up and before user touches the trackpad device.
TEST=test on Chromebook.
Signed-off-by: Dudley Du <dudl@cypress.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dudley Du [Mon, 20 Jul 2015 23:57:53 +0000 (16:57 -0700)]
Input: cyapa - add proximity support for gen5 and gen6 modules
Gen5 and Gen6 trackpad devices are able to detect and report object
proximity data/events, add this function support in the cyapa driver
through the ABS_DISTANCE event.
Signed-off-by: Dudley Du <dudl@cypress.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dudley Du [Mon, 20 Jul 2015 23:53:30 +0000 (16:53 -0700)]
Input: cyapa - add gen6 device module support
Based on the cyapa core, add support for basic functionality of the gen6
trackpad devices. The driver can automatically determine what protocol
(gen3, gen5, or gen6) should be used with the attached trackpad device.
Signed-off-by: Dudley Du <dudl@cypress.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Input: tc3589x-keypad - change name of wakeup property
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Input: samsung-keypad - change name of wakeup property
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Input: gpio_keys[_polled] - change name of wakeup property
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Input: pmic8xxx-keypad - change name of wakeup property
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Acked-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Input: ads7846 - change name of wakeup property to "wakeup-source"
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Input: matrix_keypad - change name of wakeup property to "wakeup-source"
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Stephen Boyd [Fri, 17 Jul 2015 21:59:18 +0000 (14:59 -0700)]
Input: pmic8xxx-pwrkey - support shutdown
On pm8xxx PMICs, shutdown and restart are signaled to the PMIC via a pin
called PS_HOLD. When this pin goes low, the PMIC performs a configurable
power sequence. Add a .shutdown hook so that we can properly configure this
power sequence for shutdown or restart depending on the system state.
Commit 2d53809594af ("Input: zforce_ts - convert to use the gpiod
interface") converted this driver to use the gpiod functions. These
functions take the active low property into account, so we don't have
to invert the result of gpiod_get_value_cansleep(). This has been
missed in that commit. Fix it.
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two fairly simple fixes: one is a change that causes us to have a very
low queue depth leading to performance issues and the other is a null
deref occasionally in tapes thanks to use after put"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fix host max depth checking for the 'queue_depth' sysfs interface
st: null pointer dereference panic caused by use after kref_put by st_open
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes for 4.2.
Things are looking quite decent at this stage but the recent work on
the FPU support took its toll:
- fix an incorrect overly restrictive ifdef
- select O32 64-bit FP support for O32 binary compatibility
- remove workarounds for Sibyte SB1250 Pass1 parts. There are rare
fixing the workarounds is not worth the effort.
- patch up an outdated and now incorrect comment"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: fpu.h: Allow 64-bit FPU on a 64-bit MIPS R6 CPU
MIPS: SB1: Remove support for Pass 1 parts.
MIPS: Require O32 FP64 support for MIPS64 with O32 compat
MIPS: asm-offset.c: Patch up various comments refering to the old filename.
Merge branch 'parisc-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fix from Helge Deller:
"A memory leak fix from Christophe Jaillet which was introduced with
kernel 4.0 and which leads to kernel crashes on parisc after 1-3 days"
* 'parisc-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: mm: Fix a memory leak related to pmd not attached to the pgd
MIPS: fpu.h: Allow 64-bit FPU on a 64-bit MIPS R6 CPU
Commit 6134d94923d0 ("MIPS: asm: fpu: Allow 64-bit FPU on MIPS32 R6")
added support for 64-bit FPU on a 32-bit MIPS R6 processor but it missed
the 64-bit CPU case leading to FPU failures when requesting FR=1 mode
(which is always the case for MIPS R6 userland) when running a 32-bit
kernel on a 64-bit CPU. We also fix the MIPS R2 case.
After this commit, the 'return' statement in pmd_free is executed in all
cases. Even for pmd that are not attached to the pgd. So 'free_pages'
can never be called anymore, leading to a memory leak.
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"A small set of ARM fixes for -rc3, most of them not far off
one-liners, with the exception of fixing the V7 cache invalidation for
incoming SMP processors which was causing problems for SoCFPGA
devices"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: fix __virt_to_idmap build error on !MMU
ARM: invalidate L1 before enabling coherency
ARM: 8404/1: dma-mapping: fix off-by-one error in bitmap size check
ARM: 8402/1: perf: Don't use of_node after putting it
ARM: 8400/1: use virt_to_idmap to get phys_reset address
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Two families of fixes:
- Fix an FPU context related boot crash on newer x86 hardware with
larger context sizes than what most people test. To fix this
without ugly kludges or extensive reverts we had to touch core task
allocator, to allow x86 to determine the task size dynamically, at
boot time.
I've tested it on a number of x86 platforms, and I cross-built it
to a handful of architectures:
... so I hope the cross-arch impact 'none', as intended.
(by Dave Hansen)
- Fix various NMI handling related bugs unearthed by the big asm code
rewrite and generally make the NMI code more robust and more
maintainable while at it. These changes are a bit late in the
cycle, I hope they are still acceptable.
(by Andy Lutomirski)"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu, sched: Introduce CONFIG_ARCH_WANTS_DYNAMIC_TASK_STRUCT and use it on x86
x86/fpu, sched: Dynamically allocate 'struct fpu'
x86/entry/64, x86/nmi/64: Add CONFIG_DEBUG_ENTRY NMI testing code
x86/nmi/64: Make the "NMI executing" variable more consistent
x86/nmi/64: Minor asm simplification
x86/nmi/64: Use DF to avoid userspace RSP confusing nested NMI detection
x86/nmi/64: Reorder nested NMI checks
x86/nmi/64: Improve nested NMI comments
x86/nmi/64: Switch stacks on userspace NMI entry
x86/nmi/64: Remove asm code that saves CR2
x86/nmi: Enable nested do_nmi() handling for 64-bit kernels
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"Fix for a misplaced export that can cause build failures in certain
(rare) Kconfig situations"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Move the export of tick_broadcast_oneshot_control to the proper place
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"A oneliner rq throttling fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Test list head instead of list entry in throttle_cfs_rq()
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, plus a static key fix fixing /sys/devices/cpu/rdpmc"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Really allow to specify custom CC, AR or LD
perf auxtrace: Fix misplaced check for HAVE_SYNC_COMPARE_AND_SWAP_SUPPORT
perf hists browser: Take the --comm, --dsos, etc filters into account
perf symbols: Store if there is a filter in place
x86, perf: Fix static_key bug in load_mm_cr4()
tools: Copy lib/hweight.c from the kernel sources
perf tools: Fix the detached tarball wrt rbtree copy
perf thread_map: Fix the sizeof() calculation for map entries
tools lib: Improve clean target
perf stat: Fix shadow declaration of close
perf tools: Fix lockup using 32-bit compat vdso
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"Misc irq fixes:
- two driver fixes
- a Xen regression fix
- a nested irq thread crash fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gicv3-its: Fix mapping of LPIs to collections
genirq: Prevent resend to interrupts marked IRQ_NESTED_THREAD
genirq: Revert sparse irq locking around __cpu_up() and move it to x86 for now
gpio/davinci: Fix race in installing chained irq handler
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (25 commits)
lib/decompress: set the compressor name to NULL on error
mm/cma_debug: correct size input to bitmap function
mm/cma_debug: fix debugging alloc/free interface
mm/page_owner: set correct gfp_mask on page_owner
mm/page_owner: fix possible access violation
fsnotify: fix oops in fsnotify_clear_marks_by_group_flags()
/proc/$PID/cmdline: fixup empty ARGV case
dma-debug: skip debug_dma_assert_idle() when disabled
hexdump: fix for non-aligned buffers
checkpatch: fix long line messages about patch context
mm: clean up per architecture MM hook header files
MAINTAINERS: uclinux-h8-devel is moderated for non-subscribers
mailmap: update Sudeep Holla's email id
Update Viresh Kumar's email address
mm, meminit: suppress unused memory variable warning
configfs: fix kernel infoleak through user-controlled format string
include, lib: add __printf attributes to several function prototypes
s390/hugetlb: add hugepages_supported define
mm: hugetlb: allow hugepages_supported to be architecture specific
revert "s390/mm: make hugepages_supported a boot time decision"
...
Merge branch 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"These are all from Filipe, and cover a few problems we've had reported
on the list recently (along with ones he found on his own)"
* 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix file corruption after cloning inline extents
Btrfs: fix order by which delayed references are run
Btrfs: fix list transaction->pending_ordered corruption
Btrfs: fix memory leak in the extent_same ioctl
Btrfs: fix shrinking truncate when the no_holes feature is enabled
Merge tag 'rtc-v4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull rtc fixes from Alexandre Belloni:
"A few fixes for the RTC susbsystem for 4.2.
The mt6397 driver was introduce in 4.2 so it is worth fixing before
the final release. I though the compilation warning for armada38x was
fixed by akpm in commit f98b733e93e0 ("rtc-armada38x.c: remove unused
local `flags'") but he actually missed some occurrences of the
variables. Since I received 4 patches for that, I think we can
include it now.
Summary:
- fix mt6397 wakealarm creation
- remove a compilation warning for armada38x that was forgotten"
* tag 'rtc-v4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: armada38x: Remove unused variable from armada38x_rtc_set_time()
rtc: mt6397: enable wakeup before registering rtc device
Merge tag 'dm-4.2-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- revert a request-based DM core change that caused IO latency to
increase and adversely impact both throughput and system load
- fix for a use after free bug in DM core's device cleanup
- a couple DM btree removal fixes (used by dm-thinp)
- a DM thinp fix for order-5 allocation failure
- a DM thinp fix to not degrade to read-only metadata mode when in
out-of-data-space mode for longer than the 'no_space_timeout'
- fix a long-standing oversight in both dm-thinp and dm-cache by now
exporting 'needs_check' in status if it was set in metadata
- fix an embarrassing dm-cache busy-loop that caused worker threads to
eat cpu even if no IO was actively being issued to the cache device
* tag 'dm-4.2-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache: avoid calls to prealloc_free_structs() if possible
dm cache: avoid preallocation if no work in writeback_some_dirty_blocks()
dm cache: do not wake_worker() in free_migration()
dm cache: display 'needs_check' in status if it is set
dm thin: display 'needs_check' in status if it is set
dm thin: stay in out-of-data-space mode once no_space_timeout expires
dm: fix use after free crash due to incorrect cleanup sequence
Revert "dm: only run the queue on completion if congested or no requests pending"
dm btree: silence lockdep lock inversion in dm_btree_del()
dm thin: allocate the cell_sort_array dynamically
dm btree remove: fix bug in redistribute3
Dave Hansen [Fri, 17 Jul 2015 10:28:11 +0000 (12:28 +0200)]
x86/fpu, sched: Dynamically allocate 'struct fpu'
The FPU rewrite removed the dynamic allocations of 'struct fpu'.
But, this potentially wastes massive amounts of memory (2k per
task on systems that do not have AVX-512 for instance).
Instead of having a separate slab, this patch just appends the
space that we need to the 'task_struct' which we dynamically
allocate already. This saves from doing an extra slab
allocation at fork().
The only real downside here is that we have to stick everything
and the end of the task_struct. But, I think the
BUILD_BUG_ON()s I stuck in there should keep that from being too
fragile.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave@sr71.net> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1437128892-9831-2-git-send-email-mingo@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
lib/decompress: set the compressor name to NULL on error
Without this we end up using the previous name of the compressor in the
loop in unpack_rootfs. For example we get errors like "compression
method gzip not configured" even when we have CONFIG_DECOMPRESS_GZIP
enabled.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonsoo Kim [Fri, 17 Jul 2015 23:24:23 +0000 (16:24 -0700)]
mm/cma_debug: correct size input to bitmap function
In CMA, 1 bit in bitmap means 1 << order_per_bits pages so size of
bitmap is cma->count >> order_per_bits rather than just cma->count.
This patch fixes it.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Acked-by: Michal Nazarewicz <mina86@mina86.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Stefan Strogin <stefan.strogin@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonsoo Kim [Fri, 17 Jul 2015 23:24:20 +0000 (16:24 -0700)]
mm/cma_debug: fix debugging alloc/free interface
CMA has alloc/free interface for debugging. It is intended that
alloc/free occurs in specific CMA region, but, currently, alloc/free
interface is on root dir due to the bug so we can't select CMA region
where alloc/free happens.
This patch fixes this problem by making alloc/free interface per CMA
region.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Acked-by: Michal Nazarewicz <mina86@mina86.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Stefan Strogin <stefan.strogin@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonsoo Kim [Fri, 17 Jul 2015 23:24:18 +0000 (16:24 -0700)]
mm/page_owner: set correct gfp_mask on page_owner
Currently, we set wrong gfp_mask to page_owner info in case of isolated
freepage by compaction and split page. It causes incorrect mixed
pageblock report that we can get from '/proc/pagetypeinfo'. This metric
is really useful to measure fragmentation effect so should be accurate.
This patch fixes it by setting correct information.
Without this patch, after kernel build workload is finished, number of
mixed pageblock is 112 among roughly 210 movable pageblocks.
But, with this fix, output shows that mixed pageblock is just 57.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonsoo Kim [Fri, 17 Jul 2015 23:24:15 +0000 (16:24 -0700)]
mm/page_owner: fix possible access violation
When I tested my new patches, I found that page pointer which is used
for setting page_owner information is changed. This is because page
pointer is used to set new migratetype in loop. After this work, page
pointer could be out of bound. If this wrong pointer is used for
page_owner, access violation happens. Below is error message that I
got.
Jan Kara [Fri, 17 Jul 2015 23:24:12 +0000 (16:24 -0700)]
fsnotify: fix oops in fsnotify_clear_marks_by_group_flags()
fsnotify_clear_marks_by_group_flags() can race with
fsnotify_destroy_marks() so when fsnotify_destroy_mark_locked() drops
mark_mutex, a mark from the list iterated by
fsnotify_clear_marks_by_group_flags() can be freed and we dereference free
memory in the loop there.
Fix the problem by keeping mark_mutex held in
fsnotify_destroy_mark_locked(). The reason why we drop that mutex is that
we need to call a ->freeing_mark() callback which may acquire mark_mutex
again. To avoid this and similar lock inversion issues, we move the call
to ->freeing_mark() callback to the kthread destroying the mark.
Signed-off-by: Jan Kara <jack@suse.cz> Reported-by: Ashish Sangwan <a.sangwan@samsung.com> Suggested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If ARGV is somehow made empty (by doing execve(..., NULL, ...) or
manually setting ->arg_start and ->arg_end to equal values), the decision
will be based on byte which doesn't even belong to ARGV/ENVP.
So, quickly check if ARGV area is empty and report 0 to match previous
behaviour.
Haggai Eran [Fri, 17 Jul 2015 23:24:06 +0000 (16:24 -0700)]
dma-debug: skip debug_dma_assert_idle() when disabled
If dma-debug is disabled due to a memory error, DMA unmaps do not affect
the dma_active_cacheline radix tree anymore, and debug_dma_assert_idle()
can print false warnings.
Disable debug_dma_assert_idle() when dma_debug_disabled() is true.
Signed-off-by: Haggai Eran <haggaie@mellanox.com> Fixes: 0abdd7a81b7e ("dma-debug: introduce debug_dma_assert_idle()") Cc: Dan Williams <dan.j.williams@intel.com> Cc: Joerg Roedel <joro@8bytes.org> Cc: Vinod Koul <vinod.koul@intel.com> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: James Bottomley <JBottomley@Parallels.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Sebastian Ott <sebott@linux.vnet.ibm.com> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Horia Geanta <horia.geanta@freescale.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A hexdump with a buf not aligned to the groupsize causes
non-naturally-aligned memory accesses. This was causing a kernel panic
on the processor BlackFin BF527, when such an unaligned buffer was fed
by the function ubifs_scanned_corruption in fs/ubifs/scan.c .
To fix this, change accesses to the contents of the buffer so they go
through get_unaligned(). This change should be harmless to unaligned-
access-capable architectures, and any performance hit should be anyway
dwarfed by the snprintf() processing time.
Signed-off-by: Horacio Mijail Antón Quiles <hmijail@gmail.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: David Howells <dhowells@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Joe Perches <joe@perches.com> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: clean up per architecture MM hook header files
Commit 2ae416b142b6 ("mm: new mm hook framework") introduced an empty
header file (mm-arch-hooks.h) for every architecture, even those which
doesn't need to define mm hooks.
As suggested by Geert Uytterhoeven, this could be cleaned through the use
of a generic header file included via each per architecture
asm/include/Kbuild file.
The PowerPC architecture is not impacted here since this architecture has
to defined the arch_remap MM hook.
Since the get_maintainer script still reports my old email id based on
few old commits, update mailmap to report new/updated address. It also
helps to fix email address for 'git shortlog'
mm/page_alloc.c: In function 'early_page_uninitialised':
>> mm/page_alloc.c:247:6: warning: unused variable 'nid' [-Wunused-variable]
int nid = early_pfn_to_nid(pfn);
It's due to the NODE_DATA macro ignoring the nid parameter on !NUMA
configurations. This patch avoids the warning by not declaring nid.
Nicolas Iooss [Fri, 17 Jul 2015 23:23:45 +0000 (16:23 -0700)]
configfs: fix kernel infoleak through user-controlled format string
Some modules call config_item_init_type_name() and config_group_init_type_name()
with parameter "name" directly controlled by userspace. These two
functions call config_item_set_name() with this name used as a format
string, which can be used to leak information such as content of the
stack to userspace.
For example, make_netconsole_target() in netconsole module calls
config_item_init_type_name() with the name of a newly-created directory.
This means that the following commands give some unexpected output, with
configfs mounted in /sys/kernel/config/ and on a system with a
configured eth0 ethernet interface:
The directory name is correct but %lx has been interpreted in the
internal item name, displayed here in the error message used by
store_dev_name() in drivers/net/netconsole.c.
To fix this, update every caller of config_item_set_name to use "%s"
when operating on untrusted input.
This issue was found using -Wformat-security gcc flag, once a __printf
attribute has been added to config_item_set_name().
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Felipe Balbi <balbi@ti.com> Acked-by: Joel Becker <jlbec@evilplan.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nicolas Iooss [Fri, 17 Jul 2015 23:23:42 +0000 (16:23 -0700)]
include, lib: add __printf attributes to several function prototypes
Using __printf attributes helps to detect several format string issues
at compile time (even though -Wformat-security is currently disabled in
Makefile). For example it can detect when formatting a pointer as a
number, like the issue fixed in commit a3fa71c40f18 ("wl18xx: show
rx_frames_per_rates as an array as it really is"), or when the arguments
do not match the format string, c.f. for example commit 5ce1aca81435
("reiserfs: fix __RASSERT format string").
To prevent similar bugs in the future, add a __printf attribute to every
function prototype which needs one in include/linux/ and lib/. These
functions were mostly found by using gcc's -Wsuggest-attribute=format
flag.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Felipe Balbi <balbi@ti.com> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On s390 we only can enable hugepages if the underlying hardware/hypervisor
also does support this. Common code now would assume this to be
signaled by setting HPAGE_SHIFT to 0. But on s390, where we only
support one hugepage size, there is a link between HPAGE_SHIFT and
pageblock_order.
So instead of setting HPAGE_SHIFT to 0, we will implement the check for
the hardware capability.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com> Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com> Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: hugetlb: allow hugepages_supported to be architecture specific
s390 has a constant hugepage size, by setting HPAGE_SHIFT we also change
e.g. the pageblock_order, which should be independent in respect to
hugepage support.
With this patch every architecture is free to define how to check
for hugepage support.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com> Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com> Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
revert "s390/mm: make hugepages_supported a boot time decision"
Heiko noticed that the current check for hugepage support on s390 is a
little bit too harsh as systems which do not support will crash.
The reason is that pageblock_order can now get negative when we set
HPAGE_SHIFT to 0. To avoid all this and to avoid opening another can of
worms with enabling HUGETLB_PAGE_SIZE_VARIABLE I think it would be best
to simply allow architectures to define their own hugepages_supported().
Revert bea41197ead3 ("s390/mm: make hugepages_supported a boot time
decision") in preparation.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com> Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com> Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Heiko noticed that the current check for hugepage support on s390 is a
little bit too harsh as systems which do not support will crash.
The reason is that pageblock_order can now get negative when we set
HPAGE_SHIFT to 0. To avoid all this and to avoid opening another can of
worms with enabling HUGETLB_PAGE_SIZE_VARIABLE I think it would be best
to simply allow architectures to define their own hugepages_supported().
This patch (of 4): revert commit cf54e2fce51c ("s390/mm: change
HPAGE_SHIFT type to int") in preparation.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com> Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com> Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Fri, 17 Jul 2015 23:23:28 +0000 (16:23 -0700)]
openrisc: fix CONFIG_UID16 setting
openrisc-allnoconfig:
kernel/uid16.c: In function 'SYSC_setgroups16':
kernel/uid16.c:184:2: error: implicit declaration of function 'groups_alloc'
kernel/uid16.c:184:13: warning: assignment makes pointer from integer without a cast
openrisc shouldn't be setting CONFIG_UID16 when CONFIG_MULTIUSER=n.
Fixes: 2813893f8b197a1 ("kernel: conditionally support non-root users, groups and capabilities") Reported-by: Fengguang Wu <fengguang.wu@gmail.com> Cc: Iulia Manda <iulia.manda21@gmail.com> Cc: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-beck.git / log