Peter Korsgaard [Mon, 11 Oct 2010 13:02:06 +0000 (15:02 +0200)]
mxc/gpio: make _set_value work with values != 0/1
Documentation/gpio.txt specifies that the value argument to
gpio_set_value() should be handled as a boolean (E.G. != 0 is high),
so use the same logic as in _set_direction().
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
i.MX35 CPUs marked with "MCIMX357CJQ5C M99V CTHA0943B" are coming with bogus
L2 cache settings. If these settings are kept unmodified prior enabling the L2
cache the CPU runs amok immediately when its enabled.
This fix should not hurt already working CPUs, as they are using the written
register value already.
Its currently unknown if its possible to detect the production lot from the
software to fix only affected CPUs.
While at it, make sure that mxc_init_l2x0 is only executed on i.MX31/35
ARM: mx3/cpuimx35: mark otg_pdata and usbh1_pdata as maybe unused
This fixes
arch/arm/mach-mx3/mach-cpuimx35.c:143: warning: 'otg_pdata' defined but not used
arch/arm/mach-mx3/mach-cpuimx35.c:148: warning: 'usbh1_pdata' defined but not used
Simon Guinot [Thu, 7 Oct 2010 14:38:49 +0000 (16:38 +0200)]
leds: add LED driver for Big Network series LEDs
This patch add a LED class driver for LEDs found on the LaCie 2Big and
5Big Network v2 boards. The LEDs are wired to a CPLD and are controlled
through a GPIO extension bus.
Signed-off-by: Simon Guinot <sguinot@lacie.com> Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Simon Guinot [Thu, 7 Oct 2010 14:35:40 +0000 (16:35 +0200)]
leds: leds-ns2: fix private driver data storage
dev_set_drvdata() can't be used to set the driver private data pointer.
This would overwrite the led classdev object previously registered by
led_classdev_register().
Note that despite this mistake, the driver work fine because led_dat and
led_dat->cdev are at the same memory address.
Signed-off-by: Simon Guinot <sguinot@lacie.com> Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
net: atmel_macb Kconfig: remove long dependency line
Many Atmel SOC are embedding a MACB controller. This patch removes the long
dependency line for this Atmel MACB ethernet driver configuration entry.
The HAVE_NET_MACB configuration option is located in the net Kconfig file
as it may be setup by ARM/AT91 and AVR32 chips.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: David Miller <davem@davemloft.net> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Andrew Victor <linux@maxim.org.za>
AT91: fix use of clock disable on idle for AT91x40 devices
The simpler AT91x40 processors do not have the same power management
controller as the new AT91 devices. They do have a simpler power
controller module that we can use to disable the CPU clock at idle
time. Add code to support that.
AT91: at91sam9g20ek: merge 2mmc version in one board
The board-sam9g20ek-2slot-mmc.c was a revision of the at91sam9g20ek
since board revision C. It contains 2 sd/mmc slots.
This merge keep the support of the old machine ID
MACH_AT91SAM9G20EK_2MMC for backward compatibility.
Now we use the ATAG to pass the hardware functionality to kernel
with this board revision encoding
bit 0:
0 => 1 sd/mmc slot
1 => 2 sd/mmc slots connectors (board from revision C)
Linus Torvalds [Wed, 6 Oct 2010 20:27:19 +0000 (13:27 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: Octeon: Place cnmips_cu2_setup in __init memory.
MIPS: Don't place cu2 notifiers in __cpuinitdata
MIPS: Calculate VMLINUZ_LOAD_ADDRESS based on the length of vmlinux.bin
MIPS: Alchemy: Resolve prom section mismatches
MIPS: Fix syscall 64 bit number comments.
MIPS: Hookup fanotify_init, fanotify_mark, and prlimit64 syscalls.
MIPS: TX49xx: Rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN
MIPS: N32: Fix getdents64 syscall for n32
MIPS: Remove pr_<level> uses of KERN_<level>
MIPS: PNX8550: Sort out machine halt, restart and powerdown functions.
MIPS: GIC: Remove dependencies from Malta files.
MIPS: Kconfig: Fix and clarify kconfig help text for VSMP and SMTC.
MIPS: DMA: Fix computation of DMA flags from device's coherent_dma_mask.
MIPS: Audit: Fix hang in entry.S.
MIPS: Document why RELOC_HIDE is there.
MIPS: Octeon: Determine if helper needs to be built
MIPS: Use generic atomic64 for 32-bit kernels
MIPS: RM7000: Symbol should be static
MIPS: kspd: Adjust confusing if indentation
MIPS: Fix a typo.
Linus Torvalds [Wed, 6 Oct 2010 16:51:28 +0000 (09:51 -0700)]
Merge branch 'v2.6.36-rc6-urgent-fixes' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm
* 'v2.6.36-rc6-urgent-fixes' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
xen: do not initialize PV timers on HVM if !xen_have_vector_callback
xen: do not set xenstored_ready before xenbus_probe on hvm
Masking in the ack callback fails to work with handle_percpu_irq and handle_edge_irq.
The interrupt stays disabled after the first invocation since percpu and edge irq do
not unmask an interrupt after handling it. For handle_level_irq masking in the ack
is redundant because ack is always called after mask in the mask_ack function.
Masking in the ack function is required only when __do_IRQ was used instead of flow
handlers, but using __do_IRQ has been deprecated.
Remove the masking of interrupt from the ack callback.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org> Signed-off-by: Jeff Ohlstein <johlstei@codeaurora.org> Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Since powerpc uses -Werror on arch powerpc, the build was broken like
this:
cc1: warnings being treated as errors
arch/powerpc/kernel/module.c: In function 'module_finalize':
arch/powerpc/kernel/module.c:66: error: unused variable 'err'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 5 Oct 2010 18:57:37 +0000 (11:57 -0700)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf trace scripting: Fix extern struct definitions
perf ui hist browser: Fix segfault on 'a' for annotate
perf tools: Fix build breakage
perf, x86: Handle in flight NMIs on P4 platform
oprofile, ARM: Release resources on failure
oprofile: Add Support for Intel CPU Family 6 / Model 29
The "flags" member of "struct wait_queue_t" is used in several places in
the kernel code without beeing initialized by init_wait(). "flags" is
used in bitwise operations.
If "flags" not initialized then unexpected behaviour may take place.
Incorrect flags might used later in code.
Added initialization of "wait_queue_t.flags" with zero value into
"init_wait".
Signed-off-by: Evgeny Kuznetsov <EXT-Eugeny.Kuznetsov@nokia.com>
[ The bit we care about does end up being initialized by both
prepare_to_wait() and add_to_wait_queue(), so this doesn't seem to
cause actual bugs, but is definitely the right thing to do -Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 5 Oct 2010 18:29:27 +0000 (11:29 -0700)]
modules: Fix module_bug_list list corruption race
With all the recent module loading cleanups, we've minimized the code
that sits under module_mutex, fixing various deadlocks and making it
possible to do most of the module loading in parallel.
However, that whole conversion totally missed the rather obscure code
that adds a new module to the list for BUG() handling. That code was
doubly obscure because (a) the code itself lives in lib/bugs.c (for
dubious reasons) and (b) it gets called from the architecture-specific
"module_finalize()" rather than from generic code.
Calling it from arch-specific code makes no sense what-so-ever to begin
with, and is now actively wrong since that code isn't protected by the
module loading lock any more.
So this commit moves the "module_bug_{finalize,cleanup}()" calls away
from the arch-specific code, and into the generic code - and in the
process protects it with the module_mutex so that the list operations
are now safe.
Future fixups:
- move the module list handling code into kernel/module.c where it
belongs.
- get rid of 'module_bug_list' and just use the regular list of modules
(called 'modules' - imagine that) that we already create and maintain
for other reasons.
Reported-and-tested-by: Thomas Gleixner <tglx@linutronix.de> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Adrian Bunk <bunk@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
xen: do not initialize PV timers on HVM if !xen_have_vector_callback
if !xen_have_vector_callback do not initialize PV timer unconditionally
because we still don't know how many cpus are available and if there is
more than one we won't be able to receive the timer interrupts on
cpu > 0.
This patch fixes an hang at boot when Xen does not support vector
callbacks and the guest has multiple vcpus.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
xen: do not set xenstored_ready before xenbus_probe on hvm
Register_xenstore_notifier should guarantee that the caller gets
notified even if xenstore is already up.
Therefore we revert "do not notify callers from
register_xenstore_notifier" and set xenstored_read at the right time for
PV on HVM guests too.
In fact in case of PV on HVM guests xenstored is ready only after the
platform pci driver has completed the initialization, so do not set
xenstored_ready before the call to xenbus_probe().
This patch fixes a shutdown_event watcher registration bug that causes
"xm shutdown" not to work properly.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Linus Torvalds [Mon, 4 Oct 2010 18:15:59 +0000 (11:15 -0700)]
Merge branch 'fix/misc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'fix/misc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: i2c/other/ak4xx-adda: Fix a compile warning with CONFIG_PROCFS=n
ALSA: prevent heap corruption in snd_ctl_new()
Linus Torvalds [Mon, 4 Oct 2010 18:13:22 +0000 (11:13 -0700)]
Merge branch 'merge-spi' of git://git.secretlab.ca/git/linux-2.6
* 'merge-spi' of git://git.secretlab.ca/git/linux-2.6:
of/spi: Fix OF-style driver binding of spi devices
spi: spi-gpio.c tests SPI_MASTER_NO_RX bit twice, but not SPI_MASTER_NO_TX
spi/mpc8xxx: fix buffer overrun on large transfers
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
vlan: dont drop packets from unknown vlans in promiscuous mode
Phonet: Correct header retrieval after pskb_may_pull
um: Proper Fix for f25c80a4: remove duplicate structure field initialization
ip_gre: Fix dependencies wrt. ipv6.
net-2.6: SYN retransmits: Add new parameter to retransmits_timed_out()
iwl3945: queue the right work if the scan needs to be aborted
mac80211: fix use-after-free
Linus Torvalds [Mon, 4 Oct 2010 18:10:26 +0000 (11:10 -0700)]
Merge branch 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: Rephrase pwrite bounds checking to avoid any potential overflow
drm/i915: Sanity check pread/pwrite
drm/i915: Use pipe state to tell when pipe is off
drm/i915: vblank status not valid while training display port
drivers/gpu/drm/i915/i915_gem.c: Add missing error handling code
drm/i915: Fix refleak during eviction.
drm/i915: fix GMCH power reporting
Hugh Dickins [Sun, 3 Oct 2010 00:49:08 +0000 (17:49 -0700)]
ksm: fix bad user data when swapping
Building under memory pressure, with KSM on 2.6.36-rc5, collapsed with
an internal compiler error: typically indicating an error in swapping.
Perhaps there's a timing issue which makes it now more likely, perhaps
it's just a long time since I tried for so long: this bug goes back to
KSM swapping in 2.6.33.
Notice how reuse_swap_page() allows an exclusive page to be reused, but
only does SetPageDirty if it can delete it from swap cache right then -
if it's currently under Writeback, it has to be left in cache and we
don't SetPageDirty, but the page can be reused. Fine, the dirty bit
will get set in the pte; but notice how zap_pte_range() does not bother
to transfer pte_dirty to page_dirty when unmapping a PageAnon.
If KSM chooses to share such a page, it will look like a clean copy of
swapcache, and not be written out to swap when its memory is needed;
then stale data read back from swap when it's needed again.
We could fix this in reuse_swap_page() (or even refuse to reuse a
page under writeback), but it's more honest to fix my oversight in
KSM's write_protect_page(). Several days of testing on three machines
confirms that this fixes the issue they showed.
Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Sun, 3 Oct 2010 00:46:06 +0000 (17:46 -0700)]
ksm: fix page_address_in_vma anon_vma oops
2.6.36-rc1 commit 21d0d443cdc1658a8c1484fdcece4803f0f96d0e "rmap:
resurrect page_address_in_vma anon_vma check" was right to resurrect
that check; but now that it's comparing anon_vma->roots instead of
just anon_vmas, there's a danger of oopsing on a NULL anon_vma.
In most cases no NULL anon_vma ever gets here; but it turns out that
occasionally KSM, when enabled on a forked or forking process, will
itself call page_address_in_vma() on a "half-KSM" page left over from
an earlier failed attempt to merge - whose page_anon_vma() is NULL.
It's my bug that those should be getting here at all: I thought they
were already dealt with, this oops proves me wrong, I'll fix it in
the next release - such pages are effectively pinned until their
process exits, since rmap cannot find their ptes (though swapoff can).
For now just work around it by making page_address_in_vma() safe (and
add a comment on why that check is wanted anyway). A similar check
in __page_check_anon_rmap() is safe because do_page_add_anon_rmap()
already excluded KSM pages.
Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Rik van Riel <riel@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shmulik Ladkani [Tue, 31 Aug 2010 10:24:19 +0000 (13:24 +0300)]
MIPS: Calculate VMLINUZ_LOAD_ADDRESS based on the length of vmlinux.bin
Fix VMLINUZ_LOAD_ADDRESS calculation to be based on the length of
vmlinux.bin, the actual uncompressed kernel binary.
Previously it was based on the length of KBUILD_IMAGE (the unstripped ELF
vmlinux), which is bigger than vmlinux.bin. As a result, vmlinuz was
loaded into a memory address higher then actually needed - a problem for
small memory platforms.
FUJITA Tomonori [Sat, 14 Aug 2010 07:02:37 +0000 (16:02 +0900)]
MIPS: TX49xx: Rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN
Architectures need to set ARCH_DMA_MINALIGN to the minimum DMA
alignment (commit a6eb9fe105d5de0053b261148cee56c94b4720ca). Defining
ARCH_KMALLOC_MINALIGN doesn't work anymore.
Bernhard Walle [Fri, 3 Sep 2010 08:15:34 +0000 (10:15 +0200)]
MIPS: N32: Fix getdents64 syscall for n32
Commit 31c984a5acabea5d8c7224dc226453022be46f33 introduced a new syscall
getdents64. However, in the syscall table, the new syscall still refers to
the old getdents which doesn't work.
The problem appeared with a system that uses the eglibc 2.12-r11187 (that
utilizes that new syscall) is very confused. The fix has been tested with
that eglibc version.
Signed-off-by: Bernhard Walle <walle@corscience.de>
To: linux-mips@linux-mips.org Cc: ddaney@caviumnetworks.com Cc: akpm@linux-foundation.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1567/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS: PNX8550: Sort out machine halt, restart and powerdown functions.
No rubbish printks - those belong to userspace. The halt function now
actually halts the system and the poweroff function was deleted because
it didn't actually power down the system.
MIPS: DMA: Fix computation of DMA flags from device's coherent_dma_mask.
This only matters for ISA devices with a 24-bit DMA limit or for devices
with a 32-bit DMA limit on systems with ZONE_DMA32 enabled. The latter
currently only affects 32-bit PCI cards on Sibyte-based systems with more
than 1GB RAM installed.
_TIF_WORK_MASK false had _TIF_SYSCALL_AUDIT set. If a thread's
_TIF_SYSCALL_AUDIT is ever set this will lead to an endless loop on the
way out from a syscall.
Currently this is only a theoretic bug as init/Kconfig doesn't allow
AUDIT_SYSCALL to be enabled for MIPS.
Andreas Bießmann [Wed, 11 Aug 2010 16:49:53 +0000 (18:49 +0200)]
MIPS: Octeon: Determine if helper needs to be built
This patch adds an config switch to determine if we need to build some
workaround helper files.
The staging driver octeon-ethernet references some symbols which are only
built when PCI is enabled. The new config switch enables these symbols in
bothe cases.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
To: linux-kernel@vger.kernel.org Cc: Andreas Bießmann <biessmann@corscience.de> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1543/ Acked-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Deng-Cheng Zhu [Wed, 9 Jun 2010 04:35:25 +0000 (12:35 +0800)]
MIPS: Use generic atomic64 for 32-bit kernels
The 64-bit kernel has already had its atomic64 functions. Except for that,
we use the generic spinlocked version. The atomic64 types and related
functions are needed for the Linux performance counter subsystem.
Julia Lawall [Thu, 5 Aug 2010 20:17:22 +0000 (22:17 +0200)]
MIPS: kspd: Adjust confusing if indentation
Indent the branch of an if.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
To: kernel-janitors@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1539/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Both python_scripting_ops and perl_scripting_ops have two global definitions.
One in trace-event-scripting.c and one in their respective scripting-engine
modules.
The issue is that depending on the linker order one definition or the other
is chosen. One is uninitialized (bss), while the other is initialized. If
the uninitialized version is chosen, then perf does not function properly.
This patch fixes this by adding the extern prefix to the definitions in
trace-event-scripting.c.
Cc: David S. Miller <davem@davemloft.net> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Robert Richter <robert.richter@amd.com>
LKML-Reference: <4c97e41a.078fd80a.7a8b.3cc9@mx.google.com> Signed-off-by: Stephane Eranian <eranian@google.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
writeback: always use sb->s_bdi for writeback purposes
We currently use struct backing_dev_info for various different purposes.
Originally it was introduced to describe a backing device which includes
an unplug and congestion function and various bits of readahead information
and VM-relevant flags. We're also using for tracking dirty inodes for
writeback.
To make writeback properly find all inodes we need to only access the
per-filesystem backing_device pointed to by the superblock in ->s_bdi
inside the writeback code, and not the instances pointeded to by
inode->i_mapping->backing_dev which can be overriden by special devices
or might not be set at all by some filesystems.
Long term we should split out the writeback-relevant bits of struct
backing_device_info (which includes more than the current bdi_writeback)
and only point to it from the superblock while leaving the traditional
backing device as a separate structure that can be overriden by devices.
The one exception for now is the block device filesystem which really
wants different writeback contexts for it's different (internal) inodes
to handle the writeout more efficiently. For now we do this with
a hack in fs-writeback.c because we're so late in the cycle, but in
the future I plan to replace this with a superblock method that allows
for multiple writeback contexts per filesystem.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Chris Wilson [Sun, 26 Sep 2010 19:50:05 +0000 (20:50 +0100)]
drm/i915: Sanity check pread/pwrite
Move the access control up from the fast paths, which are no longer
universally taken first, up into the caller. This then duplicates some
sanity checking along the slow paths, but is much simpler.
Tracked as CVE-2010-2962.
Reported-by: Kees Cook <kees@ubuntu.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: stable@kernel.org
hwmon: f71882fg: use a muxed resource lock for the Super I/O port
Sleep while acquiring a resource lock on the Super I/O port. This should
prevent collisions from causing the hardware probe to fail with -EBUSY.
Signed-off-by: Giel van Schijndel <me@mortis.eu> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Keith Packard [Sun, 3 Oct 2010 07:33:06 +0000 (00:33 -0700)]
drm/i915: Use pipe state to tell when pipe is off
Instead of waiting for the display line value to settle, we can simply
wait for the pipe configuration register 'state' bit to turn off.
Contrarywise, disabling the plane will not cause the display line
value to stop changing, so instead we wait for the vblank interrupt
bit to get set. And, we only do this when we're not about to wait for
the pipe to turn off.
Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Keith Packard [Sun, 3 Oct 2010 07:33:05 +0000 (00:33 -0700)]
drm/i915: vblank status not valid while training display port
While the display port is in training mode, vblank interrupts don't
occur. Because we have to wait for the display port output to turn on
before starting the training sequence, enable the output in 'normal'
mode so that we can tell when a vblank has occurred, then start the
training sequence.
Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Sinan Akman [Sun, 3 Oct 2010 03:28:29 +0000 (21:28 -0600)]
of/spi: Fix OF-style driver binding of spi devices
This patch adds the OF hook to the spi core so that devices
can automatically be registered based on device tree data. This fixes
a problem with spi devices not binding to drivers after the cleanup of
the spi & i2c binding code.
Signed-off-by: Sinan Akman <sinan@writeme.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Roel Kluin [Sat, 2 Oct 2010 12:03:32 +0000 (14:03 +0200)]
spi: spi-gpio.c tests SPI_MASTER_NO_RX bit twice, but not SPI_MASTER_NO_TX
The SPI_MASTER_NO_TX bit (can't do buffer write) wasn't tested. This
code was introduced in commit 3c8e1a84 (spi/spi-gpio: add support for
controllers without MISO or MOSI pin). This patch fixes a bug in
choosing which transfer ops to use.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Axel Lin [Fri, 1 Oct 2010 05:56:27 +0000 (13:56 +0800)]
regulator: max8649 - fix setting extclk_freq
The SYNC bits are BIT6 and BIT7 of MAX8649_SYNC register.
pdata->extclk_freq could be [0|1|2].
(MAX8649_EXTCLK_26MHZ|MAX8649_EXTCLK_13MHZ|MAX8649_EXTCLK_19MHZ)
It requires to left shift 6 bits to properly set extclk_freq.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Nicolas Pitre [Fri, 27 Aug 2010 03:10:50 +0000 (23:10 -0400)]
ARM: add a vma entry for the user accessible vector page
The kernel makes the high vector page visible to user space. This page
contains (amongst others) small code segments that can be executed in
user space. Make this page visible through ptrace and /proc/<pid>/mem
in order to let gdb perform code parsing needed for proper unwinding.
For example, the ERESTART_RESTARTBLOCK handler actually has a stack
frame -- it returns to a PC value stored on the user's stack. To
unwind after a "sleep" system call was interrupted twice, GDB would
have to recognize this situation and understand that stack frame
layout -- which it currently cannot do.
We could fix this by hard-coding addresses in the vector page range into
GDB, but that isn't really portable as not all of those addresses are
guaranteed to remain stable across kernel releases. And having the gdb
process make an exception for this page and get content from its own
address space for it looks strange, and it is not future proof either.
Being located above PAGE_OFFSET, this vma cannot be deleted by
user space code.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Nicolas Pitre [Wed, 22 Sep 2010 22:34:36 +0000 (18:34 -0400)]
ARM: implement CONFIG_STRICT_DEVMEM by disabling access to RAM via /dev/mem
There are very few legitimate use cases, if any, for directly accessing
system RAM through /dev/mem. So let's mimic what they do on x86 and
forbid it when CONFIG_STRICT_DEVMEM is turned on.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Nicolas Pitre [Thu, 23 Sep 2010 20:52:40 +0000 (16:52 -0400)]
ARM: do not define VMALLOC_END relative to PAGE_OFFSET
VMALLOC_END is supposed to be an absolute value, while PAGE_OFFSET may
vary depending on the selected user:kernel memory split mode through
CONFIG_VMSPLIT_*. In fact, the goal of moving PAGE_OFFSET down is to
accommodate more directly addressed RAM by the kernel below the vmalloc
area, and having VMALLOC_END move along PAGE_OFFSET is rather against
the very reason why PAGE_OFFSET can be moved in the first place.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Amit Kucheria [Wed, 1 Sep 2010 19:49:13 +0000 (22:49 +0300)]
ARM: mxc: turn off HWCAP_NEON for older versions of imx51 silicon
Versions of silicon older than TO3 have broken NEON implementation. Turn off
NEON in such cases.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org> Tested-by: Dave Martin <dave.martin@linaro.org> Tested-by: Jason Hui <jason.hui@linaro.org> Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Nicolas Pitre [Wed, 1 Sep 2010 13:37:05 +0000 (09:37 -0400)]
ARM: link board specific files after core files
This allows for board specific issues to override decisions made in generic
code that might not be suitable due to some errata or the like, by making
the initcall hooks from those board specific files run after the core ones,
therefore avoiding ugly #ifdef's in core code.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org> Tested-by: Dave Martin <dave.martin@linaro.org> Tested-by: Jason Hui <jason.hui@linaro.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: prevent infinite recursion in cifs_reconnect_tcon
cifs: set backing_dev_info on new S_ISREG inodes
David Howells [Fri, 1 Oct 2010 09:31:03 +0000 (10:31 +0100)]
MN10300: Fix flush_icache_range()
flush_icache_range() is given virtual addresses to describe the region. It
deals with these by attempting to translate them through the current set of
page tables.
This is fine for userspace memory and vmalloc()'d areas as they are governed by
page tables. However, since the regions above 0x80000000 aren't translated
through the page tables by the MMU, the kernel doesn't bother to set up page
tables for them (see paging_init()).
This means flush_icache_range() as it stands cannot be used to flush regions of
the VM area between 0x80000000 and 0x9fffffff where the kernel resides if the
data cache is operating in WriteBack mode.
To fix this, make flush_icache_range() first check for addresses in the upper
half of VM space and deal with them appropriately, before dealing with any
range in the page table mapped area.
Ordinarily, this is not a problem, but it has the capacity to make kprobes and
kgdb malfunction. It should not affect gdbstub, signal frame setup or module
loading as gdb has its own flush functions, and the others take place in the
page table mapped area only.