Chris Wilson [Wed, 20 Jul 2016 12:31:57 +0000 (13:31 +0100)]
drm/i915: Convert i915_semaphores_is_enabled over to early sanitize
Rather than recomputing whether semaphores are enabled, we can do that
computation once during early initialisation as the i915.semaphores
module parameter is now read-only.
Chris Wilson [Wed, 20 Jul 2016 12:31:55 +0000 (13:31 +0100)]
drm/i915: Treat ringbuffer writes as write to normal memory
Ringbuffers are now being written to either through LLC or WC paths, so
treating them as simply iomem is no longer adequate. However, for the
older !llc hardware, the hardware is documentated as treating the TAIL
register update as serialising, so we can relax the barriers when filling
the rings (but even if it were not, it is still an uncached register write
and so serialising anyway.).
For simplicity, let's ignore the iomem annotation.
v2: Remove iomem from ringbuffer->virtual_address
v3: And for good measure add iomem elsewhere to keep sparse happy
As these are wrappers around kref_get/kref_put() it is preferable to
follow the naming convention and use the same verb get/put in our
wrapper names for manipulating a reference to the context.
Chris Wilson [Wed, 20 Jul 2016 08:21:15 +0000 (09:21 +0100)]
drm/i915: Wait on external rendering for GEM objects
When transitioning to the GTT or CPU domain we wait on all rendering
from i915 to complete (with the optimisation of allowing concurrent read
access by both the GPU and client). We don't yet ensure all rendering
from third parties (tracked by implicit fences on the dma-buf) is
complete. Since implicitly tracked rendering by third parties will
ignore our cache-domain tracking, we have to always wait upon rendering
from third-parties when transitioning to direct access to the backing
store. We still rely on clients notifying us of cache domain changes
(i.e. they need to move to the GTT read or write domain after doing a CPU
access before letting the third party render again).
v2:
This introduces a potential WARN_ON into i915_gem_object_free() as the
current i915_vma_unbind() calls i915_gem_object_wait_rendering(). To
hit this path we first need to render with the GPU, have a dma-buf
attached with an unsignaled fence and then interrupt the wait. It does
get fixed later in the series (when i915_vma_unbind() only waits on the
active VMA and not all, including third-party, rendering.
To offset that risk, use the __i915_vma_unbind_no_wait hack.
Chris Wilson [Wed, 20 Jul 2016 08:21:14 +0000 (09:21 +0100)]
drm/i915: Mark imported dma-buf objects as being coherent
A foreign dma-buf does not share our cache domain tracking, and we rely
on the producer ensuring cache coherency. Marking them as being in the
CPU domain is incorrect.
v2: Add commentary about the GTT domain. This is not the best place for
it, but pending an actual overhaul of our domain tracking and explaining
each one, this comment should help the next reader...
Chris Wilson [Wed, 20 Jul 2016 08:21:13 +0000 (09:21 +0100)]
drm/i915: Disable waitboosting for mmioflips/semaphores
Since commit a6f766f39751 ("drm/i915: Limit ring synchronisation (sw
sempahores) RPS boosts") and commit bcafc4e38b6a ("drm/i915: Limit mmio
flip RPS boosts") we have limited the waitboosting for semaphores and
flips. Ideally we do not want to boost in either of these instances as no
userspace consumer is waiting upon the results (though a userspace producer
may be stalled trying to submit an execbuf - but in this case the
producer is being throttled due to the engine being saturated with
work). With the introduction of NO_WAITBOOST in the previous patch, we
can finally disable these needless boosts.
Chris Wilson [Wed, 20 Jul 2016 08:21:12 +0000 (09:21 +0100)]
drm/i915: Disable waitboosting for fence_wait()
We want to restrict waitboosting to known process contexts, where we can
track which clients are receiving waitboosts and prevent excessive power
wasting. For fence_wait() we do not have any client tracking and so that
leaves it open to abuse.
v2: Hide the IS_ERR_OR_NULL testing for special clients
Chris Wilson [Wed, 20 Jul 2016 08:21:11 +0000 (09:21 +0100)]
drm/i915: Derive GEM requests from dma-fence
dma-buf provides a generic fence class for interoperation between
drivers. Internally we use the request structure as a fence, and so with
only a little bit of interfacing we can rebase those requests on top of
dma-buf fences. This will allow us, in the future, to pass those fences
back to userspace or between drivers.
v2: The fence_context needs to be globally unique, not just unique to
this device.
Chris Wilson [Wed, 20 Jul 2016 08:21:10 +0000 (09:21 +0100)]
drm/i915: Mark all current requests as complete before resetting them
Following a GPU reset upon hang, we retire all the requests and then
mark them all as complete. If we mark them as complete first, we both
keep the normal retirement order (completed first then retired) and
provide a small optimisation for concurrent lookups.
Chris Wilson [Wed, 20 Jul 2016 08:21:09 +0000 (09:21 +0100)]
drm/i915: Retire oldest completed request before allocating next
In order to keep the memory allocated for requests reasonably tight, try
to reuse the oldest request (so long as it is completed and has no
external references) for the next allocation.
v2: Throw in a comment to hopefully make sure no one mistakes the
optimistic retirement of the oldest request for simply stealing it.
We have latency issues that might impact the performance: #96606.
and hangs and loading issues on resume after S4: #96526.
This is also blocking a platform milestone so let's disable
this for now while we make sure we don't have any more loading
issue, or related basic hangs and it pass BAT for real in all
platofmrs.
In case BAT is wrong let's first fix BAT before re-enable it here.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96606
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96526 Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Dave Gordon <david.s.gordon@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Stable <stable@vger.kernel.org> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Christophe Prigent <christophe.prigent@intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1468884477-30086-1-git-send-email-rodrigo.vivi@intel.com
Imre Deak [Fri, 1 Jul 2016 14:32:08 +0000 (17:32 +0300)]
drm/i915: Give proper names to MOCS entries
The purpose for each MOCS entry isn't well defined atm. Defining these
is important to remove any uncertainty about the use of these entries
for example in terms of performance and GPU/CPU coherency.
Suggested by Ville.
v4:
- Rename I915_MOCS_AUTO to I915_MOCS_PTE. (Chris)
Imre Deak [Fri, 1 Jul 2016 13:40:05 +0000 (16:40 +0300)]
drm/i915/bxt: Fix inadvertent CPU snooping due to incorrect MOCS config
Setting a write-back cache policy in the MOCS entry definition also
implies snooping, which has a considerable overhead. This is
unexpected for a few reasons:
- From user-space's point of view since it didn't want a coherent
surface (it didn't set the buffer as such via the set caching IOCTL).
- There is a separate MOCS entry field for snooping (which we never
set).
- This MOCS table is about caching in (e)LLC and there is no (e)LLC on
BXT. There is a separate table for L3 cache control.
Considering the above the current behavior of snooping looks like an
unintentional side-effect of the WB setting. Changing it to be LLC-UC
gets rid of the snooping without any ill-effects. For a coherent
surface the application would use a separate MOCS entry at index 1 and
call the set caching IOCTL to setup the PTE entries for the
corresponding buffer to be snooped. In the future we could also add a
new MOCS entry for coherent surfaces.
This resulted in 70% improvement in synthetic texturing benchmarks.
Kudos to Valtteri Rantala, Eero Tamminen and Michael T Frederick and
Ville who helped to narrow the source of problem to the kernel and to
the snooping behaviour in particular.
With a follow-up change to adjust the 3rd entry value
igt/gem_mocs_settings is passing after this change.
v2:
- Rebase on v2 of patch 1/2.
v3:
- Set the entry as LLC uncached instead of PTE-passthrough. This way
we also keep snooping disabled, but we also make the cacheability/
coherency setting indepent of the PTE which is managed by the
kernel. (Chris)
CC: Rong R Yang <rong.r.yang@intel.com> CC: Yakui Zhao <yakui.zhao@intel.com> CC: Valtteri Rantala <valtteri.rantala@intel.com> CC: Eero Tamminen <eero.t.tamminen@intel.com> CC: Michael T Frederick <michael.t.frederick@intel.com> CC: Ville Syrjälä <ville.syrjala@linux.intel.com> CC: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Imre Deak <imre.deak@intel.com> Acked-by: Zhao Yakui <yakui.zhao@intel.com> Tested-by: Rong R Yang <rong.r.yang@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1467380406-11954-3-git-send-email-imre.deak@intel.com
Imre Deak [Fri, 1 Jul 2016 13:40:04 +0000 (16:40 +0300)]
drm/i915/gen9: Clean up MOCS table definitions
Use named struct initializers for clarity. Also fix the target cache
definition to reflect its role in GEN9 onwards. On GEN8 a TC value of 0
meant ELLC but on GEN9+ it means the TC and LRU controls are taken from
the PTE.
No functional change, igt/gem_mocs_settings still passing after this
change.
v2: (Chris)
- Add back the hexa literals for the entries.
Add note that igt/gem_mocs_settings still passes.
Daniel Vetter [Fri, 15 Jul 2016 19:48:06 +0000 (21:48 +0200)]
drm/i915: Clean up kerneldoc for intel_lrc.c
Fairly minimal, there's still lots of functions without any docs, and
which aren't static. But probably we want to first clean this up some more.
- Drop the bogus const. Marking argument pointers themselves (instead of
what they point at) as const provides roughly 0 value. And it's confusing,
since the data the pointer points at _is_ being changed.
- Remove kerneldoc for static functions. Keep comments where they seem valuable.
- Indent and whitespace fixes.
- Blockquote the bit field definitions of the descriptor for correct layouting.
Daniel Vetter [Fri, 15 Jul 2016 19:48:05 +0000 (21:48 +0200)]
drm/i915: Fixup kerneldoc code snippets in intel_uncore.c
We need :: before, blank lines around and indentation with 4 _additional_
spaces to make it work. Also, don't use @param in code snippets, it results
in confusion.
Chris Wilson [Sat, 16 Jul 2016 17:42:36 +0000 (18:42 +0100)]
drm/i915: Handle ENOSPC after failing to insert a mappable node
Even after adding individual page support for GTT mmaping, we can still
fail to find any space within the mappable region, and
drm_mm_insert_node() will then report ENOSPC. We have to then handle
this error by using the shmem access to the pages.
Fixes: b50a53715f09 ("drm/i915: Support for pread/pwrite ... objects")
Testcase: igt/gem_concurrent_blit Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ankitprasad Sharma <ankitprasad.r.sharma@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com Link: http://patchwork.freedesktop.org/patch/msgid/1468690956-23480-1-git-send-email-chris@chris-wilson.co.uk Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dave Gordon [Thu, 14 Jul 2016 13:52:04 +0000 (14:52 +0100)]
drm/i915: refactor eb_get_batch()
Precursor for fix to secure batch execution. We will need to be able to
retrieve the batch VMA (as well as the batch itself) from the eb list,
so this patch extracts that part of eb_get_batch() into a separate
function, and moves both parts to a more logical place in the file, near
where the eb list is created.
Also, it may not be obvious, but the current execbuffer2 ioctl interface
requires that the buffer object containing the batch-to-be-executed be
the LAST entry in the exec2_list[] array (I expected it to be the
first!).
To clarify this, we can replace the rather obscure construct
"list_entry(eb->vmas.prev, ...)"
in the old version of eb_get_batch() with the equivalent but more
explicit
"list_last_entry(&eb->vmas,...)"
in the new eb_get_batch_vma() and of course add an explanatory comment.
Dave Gordon [Thu, 14 Jul 2016 13:52:03 +0000 (14:52 +0100)]
drm/i915: compile-time consistency check on __EXEC_OBJECT flags
Two different sets of flag bits are stored in the 'flags' member of a
'struct drm_i915_gem_exec_object2', and they're defined in two different
source files, increasing the risk of an accidental clash.
Some flags in this field are supplied by the user; these are defined in
i915_drm.h, and they start from the LSB and work up.
Other flags are defined in i915_gem_execbuffer, for internal use within
that file only; they start from the MSB and work down.
So here we add a compile-time check that the two sets of flags do not
overlap, which would cause all sorts of confusion.
Bob Paauwe [Fri, 15 Jul 2016 13:59:02 +0000 (14:59 +0100)]
drm/i915: Set legacy properties when using legacy gamma set IOCTL. (v2)
The i915 driver is now using atomic properties and atomic commit
to handle the legacy set gamma IOCTL. However, if the driver is
configured without atomic (nuclear_pageflip = false), it won't
update the legacy properties for degamma_lut, gamma_lut and ctm
leaving them out of sync with the atomic version of the properties.
Until the driver is full atomic, make sure we update the non-atomic
version of the properties.
v2: Update the comment with a FIXME. (Daniel)
v3: Update arguments of the gamma_set vfunc (Lionel)
Ville Syrjälä [Mon, 18 Jul 2016 10:15:14 +0000 (13:15 +0300)]
drm/i915: Treat eDP as always connected, again
eDP should be treated as connected even if doesn't have an EDID. In that
case we'll use the timings from the VBT. That used to be the case until
commit f21a21983ef1 ("drm/i915: Splitting intel_dp_detect")
broke things by considering even eDP disconnected if we fail to get
an EDID for it.
Fix things up again by treating eDP as always connected.
Cc: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com> Cc: Nathan D Ciobanu <nathan.d.ciobanu@intel.com> Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com> Cc: Larry Finger <larry.finger@lwfinger.net> Reported-by: Larry Finger <larry.finger@lwfinger.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96675 Cc: drm-intel-fixes@lists.freedesktop.org Fixes: f21a21983ef1 ("drm/i915: Splitting intel_dp_detect") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Larry Finger <larry.finger@lwfinger.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1468836914-16537-1-git-send-email-ville.syrjala@linux.intel.com
Chris Wilson [Fri, 15 Jul 2016 13:56:20 +0000 (14:56 +0100)]
drm/i915: Flush logical context image out to memory upon suspend
Before suspend, and especially before building the hibernation image, we
need to context image to be coherent in memory. To do this we require
that we perform a context switch to a disposable context (i.e. the
dev_priv->kernel_context) - when that switch is complete, all other
context images will be complete. This leaves the kernel_context image as
incomplete, but fortunately that is disposable and we can do a quick
fixup of the logical state after resuming.
v2: Share the nearly identical code to switch to the kernel context with
eviction.
v3: Explain why we need the switch and reset.
Testcase: igt/gem_exec_suspend # bsw
References: https://bugs.freedesktop.org/show_bug.cgi?id=96526 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1468590980-6186-2-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Fri, 15 Jul 2016 13:56:19 +0000 (14:56 +0100)]
drm/i915/evict: Always switch away from the current context
Currently execlists is exempt from emitting a request to switch each
ring away from the current context over to the dev_priv->kernel_context
(for whatever reason, just under execlists the GGTT is unlikely to be as
fragmented, however the switch may help in some extreme cases). Extract
the switcher and enable it for execlsts as well, as we need to do so in
a later patch to force the context switch before suspend. (And since for
that switch we explicitly require the disposable kernel context, rename
the extracted function.)
Chris Wilson [Wed, 13 Jul 2016 17:34:45 +0000 (18:34 +0100)]
drm/i915/fbdev: Check for the framebuffer before use
If the fbdev probing fails, and in our error path we fail to clear the
dev_priv->fbdev, then we can try and use a dangling fbdev pointer, and
in particular a NULL fb. This could also happen in pathological cases
where we try to operate on the fbdev prior to it being probed.
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1468431285-28264-2-git-send-email-chris@chris-wilson.co.uk Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Chris Wilson [Wed, 13 Jul 2016 17:34:44 +0000 (18:34 +0100)]
drm/i915/fbdev: Drain the suspend worker on retiring
Since the suspend_work can arm itself if the console_lock() is currently
held elsewhere, simply calling flush_work() doesn't guarantee that the
work is idle upon return. To do so requires using cancel_work_sync().
drm/i915: add missing condition for committing planes on crtc
The i915 driver checks for color management properties changes as part
of a plane update. Therefore a color management update must imply a
plane update, otherwise we never update the transformation matrixes
and degamma/gamma LUTs.
v2: add comment about moving the commit of color management registers
to an async worker
v3: Commit color management register right after vblank
v4: Move back color management commit condition together with planes
commit
v5: Trigger color management commit through the planes commit (Daniel)
v6: Make plane change update more readable
Fixes: 20a34e78f0d7 (drm/i915: Update color management during vblank evasion.) Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: drm-intel-fixes@lists.freedesktop.org Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
References: https://lkml.org/lkml/2016/7/14/614 Reviewed-and-tested-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1464183041-8478-1-git-send-email-lionel.g.landwerlin@intel.com
Lyude [Tue, 21 Jun 2016 21:03:44 +0000 (17:03 -0400)]
drm/i915: Enable polling when we don't have hpd
Unfortunately, there's two situations where we lose hpd right now:
- Runtime suspend
- When we've shut off all of the power wells on Valleyview/Cherryview
While it would be nice if this didn't cause issues, this has the
ability to get us in some awkward states where a user won't be able to
get their display to turn on. For instance; if we boot a Valleyview
system without any monitors connected, it won't need any of it's power
wells and thus shut them off. Since this causes us to lose HPD, this
means that unless the user knows how to ssh into their machine and do a
manual reprobe for monitors, none of the monitors they connect after
booting will actually work.
Eventually we should come up with a better fix then having to enable
polling for this, since this makes rpm a lot less useful, but for now
the infrastructure in i915 just isn't there yet to get hpd in these
situations.
Changes since v1:
- Add comment explaining the addition of the if
(!mode_config->poll_running) in intel_hpd_init()
- Remove unneeded if (!dev->mode_config.poll_enabled) in
i915_hpd_poll_init_work()
- Call to drm_helper_hpd_irq_event() after we disable polling
- Add cancel_work_sync() call to intel_hpd_cancel_work()
Changes since v2:
- Apparently dev->mode_config.poll_running doesn't actually reflect
whether or not a poll is currently in progress, and is actually used
for dynamic module paramter enabling/disabling. So now we instead
keep track of our own poll_running variable in dev_priv->hotplug
- Clean i915_hpd_poll_init_work() a little bit
Changes since v3:
- Remove the now-redundant connector loop in intel_hpd_init(), just
rely on intel_hpd_poll_enable() for setting connector->polled
correctly on each connector
- Get rid of poll_running
- Don't assign enabled in i915_hpd_poll_init_work before we actually
lock dev->mode_config.mutex
- Wrap enabled assignment in i915_hpd_poll_init_work() in READ_ONCE()
for doc purposes
- Do the same for dev_priv->hotplug.poll_enabled with WRITE_ONCE in
intel_hpd_poll_enable()
- Add some comments about racing not mattering in intel_hpd_poll_enable
Changes since v4:
- Rename intel_hpd_poll_enable() to intel_hpd_poll_init()
- Drop the bool argument from intel_hpd_poll_init()
- Remove redundant calls to intel_hpd_poll_init()
- Rename poll_enable_work to poll_init_work
- Add some kerneldoc for intel_hpd_poll_init()
- Cross-reference intel_hpd_poll_init() in intel_hpd_init()
- Just copy the loop from intel_hpd_init() in intel_hpd_poll_init()
Changes since v5:
- Minor kerneldoc nitpicks
Cc: stable@vger.kernel.org Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Lyude <cpaul@redhat.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Lyude [Tue, 21 Jun 2016 21:03:43 +0000 (17:03 -0400)]
drm/i915/vlv: Disable HPD in valleyview_crt_detect_hotplug()
One of the things preventing us from using polling is the fact that
calling valleyview_crt_detect_hotplug() when there's a VGA cable
connected results in sending another hotplug. With polling enabled when
HPD is disabled, this results in a scenario like this:
- We enable power wells and reset the ADPA
- output_poll_exec does force probe on VGA, triggering a hpd
- HPD handler waits for poll to unlock dev->mode_config.mutex
- output_poll_exec shuts off the ADPA, unlocks dev->mode_config.mutex
- HPD handler runs, resets ADPA and brings us back to the start
This results in an endless irq storm getting sent from the ADPA
whenever a VGA connector gets detected in the middle of polling.
Somewhat based off of the "drm/i915: Disable CRT HPD around force
trigger" patch Ville Syrjälä sent a while back
Cc: stable@vger.kernel.org Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Lyude <cpaul@redhat.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Lyude [Tue, 21 Jun 2016 21:03:42 +0000 (17:03 -0400)]
drm/i915/vlv: Reset the ADPA in vlv_display_power_well_init()
While VGA hotplugging worked(ish) before, it looks like that was mainly
because we'd unintentionally enable it in
valleyview_crt_detect_hotplug() when we did a force trigger. This
doesn't work reliably enough because whenever the display powerwell on
vlv gets disabled, the values set in VLV_ADPA get cleared and
consequently VGA hotplugging gets disabled. This causes bugs such as one
we found on an Intel NUC, where doing the following sequence of
hotplugs:
Would result in VGA hotplugging becoming disabled, due to the powerwells
getting toggled in the process of connecting HDMI.
Changes since v3:
- Expose intel_crt_reset() through intel_drv.h and call that in
vlv_display_power_well_init() instead of
encoder->base.funcs->reset(&encoder->base);
Changes since v2:
- Use intel_encoder structs instead of drm_encoder structs
Changes since v1:
- Instead of handling the register writes ourself, we just reuse
intel_crt_detect()
- Instead of resetting the ADPA during display IRQ installation, we now
reset them in vlv_display_power_well_init()
Cc: stable@vger.kernel.org Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Lyude <cpaul@redhat.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Rebase over dev_priv/drm_device embedding.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 13 Jul 2016 08:10:37 +0000 (09:10 +0100)]
drm/i915: Defer enabling rc6 til after we submit the first batch/context
Some hardware requires a valid render context before it can initiate
rc6 power gating of the GPU; the default state of the GPU is not
sufficient and may lead to undefined behaviour. The first execution of
any batch will load the "golden render state", at which point it is safe
to enable rc6. As we do not forcibly load the kernel context at resume,
we have to hook into the batch submission to be sure that the render
state is setup before enabling rc6.
However, since we don't enable powersaving until that first batch, we
queued a delayed task in order to guarantee that the batch is indeed
submitted.
v2: Rearrange intel_disable_gt_powersave() to match.
v3: Apply user specified cur_freq (or idle_freq if not set).
v4: Give in, and supply a delayed work to autoenable rc6
v5: Mika suggested a couple of better names for delayed_resume_work
v6: Rebalance rpm_put around the autoenable task
Chris Wilson [Wed, 13 Jul 2016 08:10:35 +0000 (09:10 +0100)]
drm/i915: Define a separate variable and control for RPS waitboost frequency
To allow the user finer control over waitboosting, allow them to set the
frequency we request for the boost. This also them allows to effectively
disable the boosting by setting the boost request to a low frequency.
Chris Wilson [Wed, 13 Jul 2016 08:10:32 +0000 (09:10 +0100)]
drm/i915: Preserve current RPS frequency across init
Select idle frequency during initialisation, then reset the last known
frequency when re-enabling. This allows us to preserve the user selected
frequency across resets.
v2: Stop CHV from overriding the user's choice in cherryview_enable_rps()
Chris Wilson [Wed, 13 Jul 2016 08:10:31 +0000 (09:10 +0100)]
drm/i915: Flush GT idle status upon reset
Upon resetting the GPU, we force the engines to be idle by clearing
their request lists. However, I neglected to clear the GT active status
and so the next request following the reset was not marking the device
as busy again. (We had to wait until any outstanding retire worker
finally ran and cleared the active status.)
Ville Syrjälä [Tue, 12 Jul 2016 12:00:37 +0000 (15:00 +0300)]
drm/i915: Ignore panel type from OpRegion on SKL
Dell XPS 13 9350 apparently doesn't like it when we use the panel type
from OpRegion. The OpRegion panel type (0) tells us to use use low
vswing for eDP, whereas the VBT panel type (2) tells us to use normal
vswing. The problem is that low vswing results in some display flickers.
Since no one seems to know how this stuff is supposed to be handled,
let's just ignore the OpRegion panel type on SKL for now.
v2: Print the panel type correctly in the debug output
Reported-by: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: drm-intel-fixes@lists.freedesktop.org
References: https://lists.freedesktop.org/archives/intel-gfx/2016-June/098826.html Fixes: a05628195a0d ("drm/i915: Get panel_type from OpRegion panel details") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1468324837-29237-1-git-send-email-ville.syrjala@linux.intel.com Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Chris Wilson <chris-wilson.co.uk>
With the unified common engine setup done, and the execlist engine
initialization loop clearly split into two phases, we can eliminate
the separate legacy engine initialization code.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Chris Wilson <chris-wilson.co.uk>
Move the execlist engine setup to vfuncs so that the engine
init loop is clearly split into the mode agnostic and
specific steps.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Chris Wilson <chris-wilson.co.uk>
Dave Gordon [Wed, 13 Jul 2016 15:03:35 +0000 (16:03 +0100)]
drm/i915: unify first-stage engine struct setup
intel_lrc.c has a table of "logical rings" (meaning engines), while
intel_ringbuffer.c has separately open-coded initialisation for each
engine. We can deduplicate this somewhat by using the same first-stage
engine-setup function for both modes.
So here we expose the function that transfers information from the
static table of (all) known engines to the dev_priv->engine array of
engines available on this device (adjusting the names along the way)
and then embed calls to it in both the LRC and the legacy-mode setup.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com> Reviewed-by: Chris Wilson <chris-wilson.co.uk> Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Ville Syrjälä [Tue, 12 Jul 2016 16:24:47 +0000 (19:24 +0300)]
drm/i915: Unbreak interrupts on pre-gen6
Prior to gen6 we didn't have per-ring IMR registers, which means that
since commit 61ff75ac20ff ("drm/i915: Simplify enabling
user-interrupts with L3-remapping") we're now masking off all interrupts
when init_render_ring() gets called. That's rather rude. Let's limit
the ring IMR frobbing to machines that actually have the per-ring IMR
registers.
Chris Wilson [Tue, 12 Jul 2016 11:55:29 +0000 (12:55 +0100)]
drm/i915: Provide argument names for static stubs
Make sure we keep kbuilder happy in all of its random configs by
providing argument names for compile-time stubs.
In file included from drivers/gpu/drm/i915/intel_dp_mst.c:27:0:
drivers/gpu/drm/i915/i915_drv.h: In function 'i915_debugfs_register':
>> drivers/gpu/drm/i915/i915_drv.h:3612:48: error: parameter name omitted
static inline int i915_debugfs_register(struct drm_i915_private *) {return 0;}
^~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/i915_drv.h: In function 'i915_debugfs_unregister':
drivers/gpu/drm/i915/i915_drv.h:3613:51: error: parameter name omitted
static inline void i915_debugfs_unregister(struct drm_i915_private *) {}
Chris Wilson [Mon, 11 Jul 2016 13:46:17 +0000 (14:46 +0100)]
drm/i915: Update ifdeffery for mutex->owner
In commit 7608a43d8f2e ("locking/mutexes: Use MUTEX_SPIN_ON_OWNER when
appropriate") the owner field in the mutex was updated from being
dependent upon CONFIG_SMP to using optimistic spin. Update our peek
function to suite.
Now that the last couple of hacks have been removed from the runtime
powermanagement users, we can fully enable the asserts by preventing the
temptation to disable them when our code is buggy.
Chris Wilson [Sat, 9 Jul 2016 09:12:06 +0000 (10:12 +0100)]
drm/i915: Kick hangcheck from retire worker
Let's ensure that we cannot run indefinitely without the hangcheck
worker being queued. We removed it from being kicked on every request
because we were kicking it a few millions times in every hangcheck
interval and only once is necessary! However, that leaves us with the
issue of what if userspace never waits for a request, or runs out of
resources, what if userspace just issues a request then spins on
BUSY_IOCTL?
Chris Wilson [Sat, 9 Jul 2016 09:12:05 +0000 (10:12 +0100)]
drm/i915/breadcrumbs: Queue hangcheck before sleeping
Never go to sleep waiting on the GPU without first ensuring that we will
get woken up.
We have a choice of queuing the hangcheck before every schedule() or the
first time we wakeup. In order to simply accommodate both the signaler
and the ordinary waiter, move the queuing to the common point of
enabling the irq. We lose the paranoid safety of ensuring that the
hangcheck is active before the sleep, but avoid code duplication (and
redundant hangcheck queuing).
Chris Wilson [Fri, 24 Jun 2016 13:07:14 +0000 (14:07 +0100)]
drm/i915: Fill unused GGTT with scratch pages for VT-d
One of the numerous VT-d workarounds we require is that the display
hardware reads past the end of the buffer triggering VT-d faults. This
is acknowledged in the code as being safe "since we fill the unused
portions of the GGTT with the scratch page". Alas, that is no longer
always true and so we trigger DMAR read faults.
Skylake also requires another workaround to avoid mixing VT-d and
unpopulated PTE, and so there we also need to ensure we fill unused
entries with the scratch page.
Reported-by: Mike Lothian <mike@fireburn.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96584 Fixes: f7770bfd9fd2 ("drm/i915: Skip clearing the GGTT on full-ppgtt systems") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: David Weinehall <david.weinehall@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1466773634-8106-1-git-send-email-chris@chris-wilson.co.uk Reviewed-by: David Weinehall <david.weinehall@intel.com>
drm/i915: Introduce Kabypoint PCH for Kabylake H/DT.
Some Kabylake SKUs are going to use Kabypoint PCH.
It is mainly for Halo and DT ones.
>From our specs it doesn't seem that KBP brings
any change on the display south engine. So let's consider
this as a continuation of SunrisePoint, i.e., SPT+.
Since it is easy to get confused by a letter change:
KBL = Kabylake - CPU/GPU codename.
KBP = Kabypoint - PCH codename.
Ville Syrjälä [Wed, 22 Jun 2016 18:57:09 +0000 (21:57 +0300)]
drm/i915: Check for invalid cloning earlier during modeset
Move the encoder cloning check to happen earlier in the modeset. The
main benefit will be that the debug output from a failed modeset will
be less confusing as output_types can not indicate an invalid
configuration during the later computation stages.
For instance, what happened to me was kms_setmode was attempting one
of its invalid cloning checks during which it asked for DP+VGA cloning
on HSW. In this case the DP .compute_config() was executed after
the FDI .compute_config() leaving the DP link clock (1.62 in this case)
in port_clock, and then later the FDI BW computation tried to use that
as the FDI link clock (which should always be 2.7). 1.62 x 2 wasn't
enough for the mode it was trying to use, and so it ended up rejecting
the modeset, not because of an invalid cloning configuration, but
because of supposedly running out of FDI bandwidth. Took me a while
to figure out what had actually happened.
Ville Syrjälä [Wed, 22 Jun 2016 18:57:07 +0000 (21:57 +0300)]
drm/i915: Kill has_dsi_encoder
has_dsi_encoder was introduced to indicate that the pipe is driving
a DSI encoder. Now that we have the output_types bitmask that can
tell us the same thing, let's just kill has_dsi_encoder.
INTEL_OUTPUT_DISPLAYPORT hsa been bugging me for a long time. It always
looks out of place besides INTEL_OUTPUT_EDP and INTEL_OUTPUT_DP_MST.
Let's just rename it to INTEL_OUTPUT_DP.
Ville Syrjälä [Wed, 22 Jun 2016 18:57:05 +0000 (21:57 +0300)]
drm/i915: Replace some open coded intel_crtc_has_dp_encoder()s
A bunch of places still look for DP encoders manually. Just call
intel_crtc_has_dp_encoder(). Note that many of these places don't
look for EDP or DP_MST, but it's still fine to replace them because
* for audio we don't enable audio on eDP anyway
* the code that lack DP MST check is only for plaforms that
don't support MST anyway
Ville Syrjälä [Wed, 22 Jun 2016 18:57:04 +0000 (21:57 +0300)]
drm/i915: Kill has_dp_encoder from pipe_config
Use the new output_types bitmask instead of has_dp_encoder.
To make it less oainlful provide a small helper
(intel_crtc_has_dp_encoder()) to do the bitsy stuff.
Ville Syrjälä [Wed, 22 Jun 2016 18:57:03 +0000 (21:57 +0300)]
drm/i915: Replace manual lvds and sdvo/hdmi counting with intel_crtc_has_type()
Since we now have the output_types bitmaks in the crtc state, there's no
need to iterate through all the encoders to see if an LVDS or SDVO/HDMI
encoder might be present.
Ville Syrjälä [Wed, 22 Jun 2016 18:57:02 +0000 (21:57 +0300)]
drm/i915: Unify intel_pipe_has_type() and intel_pipe_will_have_type()
With the introduction of the output_types mask, intel_pipe_has_type()
and intel_pipe_will_have_type() are basically the same thing. Replace
them with a new intel_crtc_has_type() (identical to
intel_pipe_will_have_type() actually).
v2: Rebase
v3: Make intel_crtc_has_type() static inline (Chris)
Ville Syrjälä [Wed, 22 Jun 2016 18:57:01 +0000 (21:57 +0300)]
drm/i915: Add output_types bitmask into the crtc state
Rather than looping through encoders to see which encoder types
are being driven by the pipe, add an output_types bitmask into
the crtc state and populate it prior to compute_config and during
state readout.
v2: Determine output_types before .compute_config() hooks are called
Ville Syrjälä [Wed, 22 Jun 2016 18:56:59 +0000 (21:56 +0300)]
drm/i915: Don't mark eDP encoders as MST capable
If we've determined that the encoder is eDP, we shouldn't try to use MST
on it. Or at least the code doesn't seem to expect that since there are
some type==DP checks in the MST code.
Dave Gordon [Wed, 6 Jul 2016 14:30:11 +0000 (15:30 +0100)]
drm/i915: avoid wait_for_atomic() in non-atomic host2guc_action()
Rather than using wait_for_atomic() when chacking for a response from
the GuC, we can get the effect of a hybrid spin/sleep wait by breaking
it into two stages. First, spin-wait for up to 10us to minimise latency
for "quick" commands; then, if that times out, sleep-wait for up 10ms
(the maximum allowed for a "slow" command).
Being able to do this depends on the recent patch 18f4b84 drm/i915: Use atomic waits for short non-atomic ones
and is similar to the hybrid approach in 1758b90 drm/i915: Use a hybrid scheme for fast register waits
(although we can't use that as-is, because that interface doesn't quite
match what we need here).
Chris Wilson [Wed, 6 Jul 2016 11:39:02 +0000 (12:39 +0100)]
drm/i915: Group the irq breadcrumb variables into the same cacheline
As we inspect both the tasklet (to check for an active bottom-half) and
set the irq-posted flag at the same time (both in the interrupt handler
and then in the bottom-halt), group those two together into the same
cacheline. (Not having total control over placement of the struct means
we can't guarantee the cacheline boundary, we need to align the kmalloc
and then each struct, but the grouping should help.)
v2: Try a couple of different names for the state touched by the user
interrupt handler.
Chris Wilson [Wed, 6 Jul 2016 11:39:01 +0000 (12:39 +0100)]
drm/i915: Wake up the bottom-half if we steal their interrupt
Following on from the scenario Tvrtko envisioned to explain a hard-to-hit
race with multiple first waiters, we could also then race in the
__i915_request_irq_complete() and the bottom-half may miss the vital
irq-seqno barrier and so go to sleep not noticing their seqno is
complete.
Chris Wilson [Wed, 6 Jul 2016 11:39:00 +0000 (12:39 +0100)]
drm/i915: Always double check for a missed interrupt for new bottom halves
After assigning ourselves as the new bottom-half, we must perform a
cursory check to prevent a missed interrupt. Either we miss the interrupt
whilst programming the hardware, or if there was a previous waiter (for
a later seqno) they may be woken instead of us (due to the inherent race
in the unlocked read of b->tasklet in the irq handler) and so we miss the
wake up.
Spotted-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96806 Fixes: 688e6c725816 ("drm/i915: Slaughter the thundering... herd") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1467805142-22219-1-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Tue, 5 Jul 2016 09:40:23 +0000 (10:40 +0100)]
drm/i915: Convert dev_priv->dev backpointers to dev_priv->drm
Since drm_i915_private is now a subclass of drm_device we do not need to
chase the drm_i915_private->dev backpointer and can instead simply
access drm_i915_private->drm directly.
text data bss dec hex filename 1068757 4565 416 1073738 10624a drivers/gpu/drm/i915/i915.ko 1066949 4565 416 1071930 105b3a drivers/gpu/drm/i915/i915.ko
Created by the coccinelle script:
@@
struct drm_i915_private *d;
identifier i;
@@
(
- d->dev->i
+ d->drm.i
|
- d->dev
+ &d->drm
)
and for good measure the dev_priv->dev backpointer was removed entirely.
Chris Wilson [Tue, 5 Jul 2016 09:40:21 +0000 (10:40 +0100)]
drm/i915: Remove use of dev_priv->dev backpointer in __i915_printk()
As we can just directly use drm_dev->drm.dev, we do not need the
drm_dev->dev backpointer anymore and can also loose the warning about
order of __i915_printk() and our initialisation (which is now always
safe).
Chris Wilson [Mon, 4 Jul 2016 07:48:33 +0000 (08:48 +0100)]
drm/i915: Skip capturing an error state if we already have one
As we only ever keep the first error state around, we can avoid some
work that can be quite intrusive if we don't record the error the second
time around. This does move the race whereby the user could discard one
error state as the second is being captured, but that race exists in the
current code and we hope that recapturing error state is only done for
debugging.
Note that as we discard the error state for simulated errors, igt that
exercise error capture continue to function.
Chris Wilson [Tue, 5 Jul 2016 07:54:36 +0000 (08:54 +0100)]
drm/i915: Replace lockless_dereference(bool) with READ_ONCE()
After Joonas complained about using READ_ONCE() on the only use of the
variable in the function, where the intent was to simply document that
the read was intentionally racy and unlocked, I switched the READ_ONCE()
over to lockless_dereference(). However, in linux-next that has a
stronger type-check to only allow pointers and is no longer
interchangeable with READ_ONCE(), see commit 331b6d8c7afc
("locking/barriers: Validate lockless_dereference() is used on a pointer
type")
drm/i915: Explicitly convert some macros to boolean values
Some IS_ and HAS_ macros can return any non-zero value for true.
One potential problem with that is that someone could assign
them to integers and be surprised with the result. Therefore it
is probably safer to do the conversion to 0/1 in the macros
themselves.
Luckily this does not seem to have an effect on code size.
Only one call site was getting bit by this and a patch for
that has been sent as "drm/i915/guc: Protect against HAS_GUC_*
returning true values other than one".
v2: Added some extra braces as suggested by checkpatch.
Chris Wilson [Mon, 4 Jul 2016 10:34:36 +0000 (11:34 +0100)]
drm/i915: Mass convert dev->dev_private to to_i915(dev)
Since we now subclass struct drm_device, we can save pointer dances by
noting the equivalence of struct drm_device and struct drm_i915_private,
i.e. by using to_i915().
text data bss dec hex filename 1073824 4562 416 1078802 107612 drivers/gpu/drm/i915/i915.ko 1068976 4562 416 1073954 106322 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Fri, 17 Jun 2016 13:35:05 +0000 (14:35 +0100)]
drm/i915: Limit i915_ring_test_irq debugfs to actual rings
For simplicity in testing, only report known rings in the mask. This
allows userspace to try and trigger a missed irq on every ring and do a
comparison between i915_ring_test_irq and i915_ring_missed_irq to see if
any rings failed.
v2: Move the debug message to after the rings are selected (so that the
message accurately reflects reality)
Chris Wilson [Sun, 3 Jul 2016 17:29:33 +0000 (18:29 +0100)]
drm/i915: Hold irq uncore.lock when initialising fw_domains
Acquiring the forcewake domain asserts that it is in an atomic section
(as we always expect to be under the uncore.lock). This is true except for
initialising the domains on Ivybridge, and so we generate a warning.
Wrap the manual usage of fw_domains inside the spin_lock.
Chris Wilson [Mon, 4 Jul 2016 07:08:39 +0000 (08:08 +0100)]
drm/i915: Allow userspace to request no-error-capture upon GPU hangs
igt likes to inject GPU hangs into its command streams. However, as we
expect these hangs, we don't actually want them recorded in the dmesg
output or stored in the i915_error_state (usually). To accommodate this
allow userspace to set a flag on the context that any hang emanating
from that context will not be recorded. We still do the error capture
(otherwise how do we find the guilty context and know its intent?) as
part of the reason for random GPU hang injection is to exercise the race
conditions between the error capture and normal execution.
v2: Split out the request->ringbuf error capture changes.
v3: Move the flag defines next to the intel_context->flags definition
Chris Wilson [Mon, 4 Jul 2016 07:08:38 +0000 (08:08 +0100)]
drm/i915: Record the ringbuffer associated with the request
The request tells us where to read the ringbuf from, so use that
information to simplify the error capture. If no request was active at
the time of the hang, the ring is idle and there is no information
inside the ring pertaining to the hang.
Note carefully that this will reduce the amount of information stored in
the error state - any ring without an active request will not be
recorded.
projects / linux-beck.git / log