Sunil Goutham [Wed, 24 Feb 2016 11:10:50 +0000 (16:40 +0530)]
net: thunderx: Fix for Qset error due to CQ full
On Thunderx pass 1.x and pass2 due to a HW errata default CQ
DROP_LEVEL of 0x80 is not sufficient to avoid CQ_WR_FULL Qset
error when packets are being received at >20Mpps resulting in
complete stall of packet reception.
This patch will configure it to 0x100 which is what is expected
by HW on Thunderx. On future passes of thunderx and other chips
HW default/reset value will be 0x100 or higher hence not overwritten.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com> Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There will be a log spam when there is no cable plugged. Please refer to
following links. https://bugzilla.kernel.org/show_bug.cgi?id=104351
https://bugzilla.kernel.org/show_bug.cgi?id=107421
This issue is caused by runtime power management. When there is no cable
plugged, the driver will be suspend (runtime suspend) by OS and NIC will be
put into the D3 state. During this time, if OS call rtl8169_get_stats64()
to dump tally counter, because NIC is in D3 state, the register value read
by driver will return all 0xff. This will let driver think tally counter
flag is not toggled and then sends the warning message "rtl_counters_cond
== 1 (loop: 1000, delay: 10)" to kernel log.
For fixing this issue, 1.add checking driver's pm runtime status in
rtl8169_get_stats64(). 2.dump tally counter before going runtime suspend
for counter accuracy in runtime suspend.
Signed-off-by: Chunhao Lin <hau@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We need to update the skb->csum after pulling the skb, otherwise
an unnecessary checksum (re)computation can ocure for IGMP/MLD packets
in the bridge code. Additionally this fixes the following splats for
network devices / bridge ports with support for and enabled RX checksum
offloading:
[...]
[ 43.986968] eth0: hw csum failure
[ 43.990344] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 4.4.0 #2
[ 43.996193] Hardware name: BCM2709
[ 43.999647] [<800204e0>] (unwind_backtrace) from [<8001cf14>] (show_stack+0x10/0x14)
[ 44.007432] [<8001cf14>] (show_stack) from [<801ab614>] (dump_stack+0x80/0x90)
[ 44.014695] [<801ab614>] (dump_stack) from [<802e4548>] (__skb_checksum_complete+0x6c/0xac)
[ 44.023090] [<802e4548>] (__skb_checksum_complete) from [<803a055c>] (ipv6_mc_validate_checksum+0x104/0x178)
[ 44.032959] [<803a055c>] (ipv6_mc_validate_checksum) from [<802e111c>] (skb_checksum_trimmed+0x130/0x188)
[ 44.042565] [<802e111c>] (skb_checksum_trimmed) from [<803a06e8>] (ipv6_mc_check_mld+0x118/0x338)
[ 44.051501] [<803a06e8>] (ipv6_mc_check_mld) from [<803b2c98>] (br_multicast_rcv+0x5dc/0xd00)
[ 44.060077] [<803b2c98>] (br_multicast_rcv) from [<803aa510>] (br_handle_frame_finish+0xac/0x51c)
[...]
Fixes: 9afd85c9e455 ("net: Export IGMP/MLD message validation code") Reported-by: Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Wahren [Tue, 23 Feb 2016 19:23:24 +0000 (19:23 +0000)]
net: qca_spi: clear IFF_TX_SKB_SHARING
ether_setup sets IFF_TX_SKB_SHARING but this is not supported by
qca_spi as it modifies the skb on xmit.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Fixes: 291ab06ecf67 (net: qualcomm: new Ethernet over SPI driver for QCA7000) Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Wahren [Tue, 23 Feb 2016 19:23:23 +0000 (19:23 +0000)]
net: qca_spi: Don't clear IFF_BROADCAST
Currently qcaspi_netdev_setup accidentally clears IFF_BROADCAST.
So fix this by keeping the flags from ether_setup.
Reported-by: Michael Heimpold <michael.heimpold@i2se.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Fixes: 291ab06ecf67 (net: qualcomm: new Ethernet over SPI driver for QCA7000) Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 23 Feb 2016 18:10:26 +0000 (10:10 -0800)]
net: vrf: Remove direct access to skb->data
Nik pointed that the VRF driver should be using skb_header_pointer
instead of accessing skb->data and bits beyond directly which can
be garbage.
Fixes: 35402e313663 ("net: Add IPv6 support to VRF device") Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Diego Viola [Tue, 23 Feb 2016 15:04:04 +0000 (12:04 -0300)]
net: jme: fix suspend/resume on JMC260
The JMC260 network card fails to suspend/resume because the call to
jme_start_irq() was too early, moving the call to jme_start_irq() after
the call to jme_reset_link() makes it work.
Prior this change suspend/resume would fail unless /sys/power/pm_async=0
was explicitly specified.
David S. Miller [Wed, 24 Feb 2016 21:58:12 +0000 (16:58 -0500)]
Merge tag 'mac80211-for-davem-2016-02-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Another small set of fixes:
* stop critical protocol session on disconnect to avoid
it getting stuck
* wext: fix two RTNL message ordering issues
* fix an uninitialized value (found by KASAN)
* fix an out-of-bounds access (also found by KASAN)
* clear connection keys when freeing them in all cases
(IBSS, all other places already did so)
* fix expected throughput unit to get consistent values
* set default TX aggregation timeout to 0 in minstrel
to avoid (really just hide) issues and perform better
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Tue, 23 Feb 2016 01:05:26 +0000 (02:05 +0100)]
bpf: fix csum setting for bpf_set_tunnel_key
The fix in 35e2d1152b22 ("tunnels: Allow IPv6 UDP checksums to be correctly
controlled.") changed behavior for bpf_set_tunnel_key() when in use with
IPv6 and thus uncovered a bug that TUNNEL_CSUM needed to be set but wasn't.
As a result, the stack dropped ingress vxlan IPv6 packets, that have been
sent via eBPF through collect meta data mode due to checksum now being zero.
Since after LCO, we enable IPv4 checksum by default, so make that analogous
and only provide a flag BPF_F_ZERO_CSUM_TX for the user to turn it off in
IPv4 case.
Fixes: 35e2d1152b22 ("tunnels: Allow IPv6 UDP checksums to be correctly controlled.") Fixes: c6c33454072f ("bpf: support ipv6 for bpf_skb_{set,get}_tunnel_key") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4: only create late gso-skb if skb is already set up with CHECKSUM_PARTIAL
Otherwise we break the contract with GSO to only pass CHECKSUM_PARTIAL
skbs down. This can easily happen with UDP+IPv4 sockets with the first
MSG_MORE write smaller than the MTU, second write is a sendfile.
Returning -EOPNOTSUPP lets the callers fall back into normal sendmsg path,
were we calculate the checksum manually during copying.
Commit d749c9cbffd6 ("ipv4: no CHECKSUM_PARTIAL on MSG_MORE corked
sockets") started to exposes this bug.
Fixes: d749c9cbffd6 ("ipv4: no CHECKSUM_PARTIAL on MSG_MORE corked sockets") Reported-by: Jiri Benc <jbenc@redhat.com> Cc: Jiri Benc <jbenc@redhat.com> Reported-by: Wakko Warner <wakko@animx.eu.org> Cc: Wakko Warner <wakko@animx.eu.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Sebastian Frias [Mon, 22 Feb 2016 12:33:14 +0000 (13:33 +0100)]
net: ethernet: nb8800: support fixed-link DT node
Under some circumstances, e.g. when connecting to a switch, the ethernet
port will not be connected to a PHY. In that case a "fixed-link" DT node
can be used to replace it.
This patch adds support for the "fixed-link" node to the nb8800 driver.
Signed-off-by: Sebastian Frias <sf84@laposte.net> Acked-by: Mans Rullgard <mans@mansr.com> Cc: Mason <slash.tmp@free.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 22 Feb 2016 07:10:26 +0000 (02:10 -0500)]
bnxt_en: Fix zero padding of tx push data.
The arithmetic to zero pad the last 64-bit word in the push buffer is not
correct.
1. It should be pdata + length to get to the end.
2. 'pdata' is void pointer and passing it to PTR_ALIGN() will cast the
aligned pointer to void. Pass 'end' which is u64 pointer to PTR_ALIGN()
instead so that the aligned pointer - 1 is the last 64-bit pointer to data.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bernie Harris [Sun, 21 Feb 2016 23:58:05 +0000 (12:58 +1300)]
tunnel: Clear IPCB(skb)->opt before dst_link_failure called
IPCB may contain data from previous layers (in the observed case the
qdisc layer). In the observed scenario, the data was misinterpreted as
ip header options, which later caused the ihl to be set to an invalid
value (<5). This resulted in an infinite loop in the mips implementation
of ip_fast_csum.
This patch clears IPCB(skb)->opt before dst_link_failure can be called for
various types of tunnels. This change only applies to encapsulated ipv4
packets.
The code introduced in 11c21a30 which clears all of IPCB has been removed
to be consistent with these changes, and instead the opt field is cleared
unconditionally in ip_tunnel_xmit. The change in ip_tunnel_xmit applies to
SIT, GRE, and IPIP tunnels.
The relevant vti, l2tp, and pptp functions already contain similar code for
clearing the IPCB.
Signed-off-by: Bernie Harris <bernie.harris@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: convert cached rtt from usec to jiffies when feeding initial rto
Currently it's converted into msecs, thus HZ=1000 intact.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Fixes: 740b0f1841f6 ("tcp: switch rtt estimations to usec resolution") Signed-off-by: David S. Miller <davem@davemloft.net>
Arend van Spriel [Mon, 15 Feb 2016 13:35:53 +0000 (14:35 +0100)]
cfg80211: stop critical protocol session upon disconnect event
When user-space has started a critical protocol session and a disconnect
event occurs, the rdev::crit_prot_nlportid remains set. This caused a
subsequent NL80211_CMD_CRIT_PROTO_START to fail (-EBUSY). Fix this by
clearing the rdev attribute and call .crit_proto_stop() callback upon
disconnect event.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Thu, 18 Feb 2016 18:49:18 +0000 (19:49 +0100)]
mac80211: minstrel_ht: set default tx aggregation timeout to 0
The value 5000 was put here with the addition of the timeout field to
ieee80211_start_tx_ba_session. It was originally added in mac80211 to
save resources for drivers like iwlwifi, which only supports a limited
number of concurrent aggregation sessions.
Since iwlwifi does not use minstrel_ht and other drivers don't need
this, 0 is a better default - especially since there have been
recent reports of aggregation setup related issues reproduced with
ath9k. This should improve stability without causing any adverse
effects.
Cc: stable@vger.kernel.org Acked-by: Avery Pennarun <apenwarr@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
"Looks like a lot, but mostly driver fixes scattered all over as usual.
Of note:
1) Add conditional sched in nf conntrack in cleanup to avoid NMI
watchdogs. From Florian Westphal.
2) Fix deadlock in nfnetlink cttimeout, also from Floarian.
3) Fix handling of slaves in bonding ARP monitor validation, from Jay
Vosburgh.
4) Callers of ip_cmsg_send() are responsible for freeing IP options,
some were not doing so. Fix from Eric Dumazet.
5) Fix per-cpu bugs in mvneta driver, from Gregory CLEMENT.
6) Fix vlan handling in mv88e6xxx DSA driver, from Vivien Didelot.
7) bcm7xxx PHY driver bug fixes from Florian Fainelli.
8) Avoid unaligned accesses to protocol headers wrt. GRE, from
Alexander Duyck.
9) SKB leaks and other problems in arc_emac driver, from Alexander
Kochetkov.
10) tcp_v4_inbound_md5_hash() releases listener socket instead of
request socket on error path, oops. Fix from Eric Dumazet.
11) Missing socket release in pppoe_rcv_core() that seems to have
existed basically forever. From Guillaume Nault.
12) Missing slave_dev unregister in dsa_slave_create() error path,
from Florian Fainelli.
13) crypto_alloc_hash() never returns NULL, fix return value check in
__tcp_alloc_md5sig_pool. From Insu Yun.
14) Properly expire exception route entries in ipv4, from Xin Long.
15) Fix races in tcp/dccp listener socket dismantle, from Eric
Dumazet.
16) Don't set IFF_TX_SKB_SHARING in vxlan, geneve, or GRE, it's not
legal. These drivers modify the SKB on transmit. From Jiri Benc.
17) Fix regression in the initialziation of netdev->tx_queue_len.
From Phil Sutter.
18) Missing unlock in tipc_nl_add_bc_link() error path, from Insu Yun.
19) SCTP port hash sizing does not properly ensure that table is a
power of two in size. From Neil Horman.
20) Fix initializing of software copy of MAC address in fmvj18x_cs
driver, from Ken Kawasaki"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (129 commits)
bnx2x: Fix 84833 phy command handler
bnx2x: Fix led setting for 84858 phy.
bnx2x: Correct 84858 PHY fw version
bnx2x: Fix 84833 RX CRC
bnx2x: Fix link-forcing for KR2
net: ethernet: davicom: fix devicetree irq resource
fmvj18x_cs: fix incorrect indexing of dev->dev_addr[] when copying the MAC address
Driver: Vmxnet3: Update Rx ring 2 max size
net: netcp: rework the code for get/set sw_data in dma desc
soc: ti: knav_dma: rename pad in struct knav_dma_desc to sw_data
net: ti: netcp: restore get/set_pad_info() functionality
MAINTAINERS: Drop myself as xen netback maintainer
sctp: Fix port hash table size computation
can: ems_usb: Fix possible tx overflow
Bluetooth: hci_core: Avoid mixing up req_complete and req_complete_skb
net: bcmgenet: Fix internal PHY link state
af_unix: Don't use continue to re-execute unix_stream_read_generic loop
unix_diag: fix incorrect sign extension in unix_lookup_by_ino
bnxt_en: Failure to update PHY is not fatal condition.
bnxt_en: Remove unnecessary call to update PHY settings.
...
Linus Torvalds [Mon, 22 Feb 2016 20:04:11 +0000 (12:04 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"One ocrdma fix:
- The new CQ API support was added to ocrdma, but they got the arming
logic wrong, so without this, transfers eventually fail when they
fail to arm the interrupt properly under load
Two related fixes for mlx4:
- When we added the 64bit extended counters support to the core IB
code, they forgot to update the RoCE side of the mlx4 driver (the
IB side they properly updated).
I debated whether or not to include these patches as they could be
considered feature enablement patches, but the existing code will
blindy copy the 32bit counters, whether any counters were requested
at all (a bug).
These two patches make it (a) check to see that counters were
requested and (b) copy the right counters (the 64bit support is
new, the 32bit is not). For that reason I went ahead and took
them"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/mlx4: Add support for the port info class for RoCE ports
IB/mlx4: Add support for extended counters over RoCE ports
RDMA/ocrdma: Fix arm logic to align with new cq API
Linus Torvalds [Mon, 22 Feb 2016 19:55:18 +0000 (11:55 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some bugfixes from I2C for you:
A fix for a RuntimePM regression with OMAP, a fix to enable TCO for
Lewisburg platforms, and a typo fix while we are here"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Adding Intel Lewisburg support for iTCO
i2c: uniphier: fix typos in error messages
i2c: omap: Fix PM regression with deferred probe for pm_runtime_reinit
Yuval Mintz [Sun, 21 Feb 2016 13:07:26 +0000 (15:07 +0200)]
bnx2x: Fix 84833 RX CRC
There's a problem in current 84833 phy configuration -
in case 1Gb link is configured and jumbo-sized packets are being
used, device will experience RX crc errors.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The dm9000 driver doesn't work in at least one device-tree
configuration, spitting an error message on irq resource :
[ 1.062495] dm9000 8000000.ethernet: insufficient resources
[ 1.068439] dm9000 8000000.ethernet: not found (-2).
[ 1.073451] dm9000: probe of 8000000.ethernet failed with error -2
The reason behind is that the interrupt might be provided by a gpio
controller, not probed when dm9000 is probed, and needing the probe
deferral mechanism to apply.
Currently, the interrupt is directly taken from resources. This patch
changes this to use the more generic platform_get_irq(), which handles
the deferral.
Moreover, since commit Fixes: 7085a7401ba5 ("drivers: platform: parse
IRQ flags from resources"), the interrupt trigger flags are honored in
platform_get_irq(), so remove the needless code in dm9000.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Marcel Ziswiler <marcel@ziswiler.com> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Tested-by: Sergei Ianovich <ynvich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: Bhavesh Davda <bhavesh@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series fixes a regression and add some improvements for the ease
of maintainance. Incorporated comments against v1.
Changelogs:
v2 : combined 2-3 into one patch as this involves a header change
fixed a parse warning in 3/4 per comment from Arnd.
Removed Sign-off from Arnd against 1/4
added comments in 3/3 to alert on the usage of sw data per review
comments
v1 : added 2-4 to accomodate feedback received from review
v0 : initial version to fix the regression (From Grygorii)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: netcp: rework the code for get/set sw_data in dma desc
SW data field in descriptor can be used by software to hold private
data for the driver. As there are 4 words available for this purpose,
use separate macros to place it or retrieve the same to/from
descriptors. Also do type cast of data types accordingly.
Cc: Wingman Kwok <w-kwok2@ti.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> CC: Arnd Bergmann <arnd@arndb.de> CC: Grygorii Strashko <grygorii.strashko@ti.com> CC: David Laight <David.Laight@ACULAB.COM> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
soc: ti: knav_dma: rename pad in struct knav_dma_desc to sw_data
Rename the pad to sw_data as per description of this field in the hardware
spec(refer sprugr9 from www.ti.com). Latest version of the document is
at http://www.ti.com/lit/ug/sprugr9h/sprugr9h.pdf and section 3.1
Host Packet Descriptor describes this field.
Define and use a constant for the size of sw_data field similar to
other fields in the struct for desc and document the sw_data field
in the header. As the sw_data is not touched by hw, it's type can be
changed to u32.
Rename the helpers to match with the updated dma desc field sw_data.
Cc: Wingman Kwok <w-kwok2@ti.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> CC: Arnd Bergmann <arnd@arndb.de> CC: Grygorii Strashko <grygorii.strashko@ti.com> CC: David Laight <David.Laight@ACULAB.COM> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 899077791403 ("netcp: try to reduce type confusion in
descriptors") introduces a regression in Kernel 4.5-rc1 and it breaks
get/set_pad_info() functionality.
The TI NETCP driver uses pad0 and pad1 fields of knav_dma_desc to
store DMA/MEM buffer pointer and buffer size respectively. And in both
cases for Keystone 2 the pointer type size is 32 bit regardless of
LAPE enabled or not, because CONFIG_ARCH_DMA_ADDR_T_64BIT originally
is not expected to be defined.
Unfortunately, above commit changed buffer's pointers save/restore
code (get/set_pad_info()) and added intermediate conversation to u64
which works incorrectly on 32bit Keystone 2 and causes TI NETCP driver
crash in RX/TX path due to "Unable to handle kernel NULL pointer"
exception. This issue was reported and discussed in [1].
Hence, fix it by partially reverting above commit and restoring
get/set_pad_info() functionality as it was before.
[1] https://www.mail-archive.com/netdev@vger.kernel.org/msg95361.html Cc: Wingman Kwok <w-kwok2@ti.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> CC: David Laight <David.Laight@ACULAB.COM> CC: Arnd Bergmann <arnd@arndb.de> Reported-by: Franklin S Cooper Jr <fcooper@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Ian Campbell [Fri, 19 Feb 2016 11:44:51 +0000 (11:44 +0000)]
MAINTAINERS: Drop myself as xen netback maintainer
Wei has been picking this up for quite a while now.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: Wei Liu <wei.liu2@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Thu, 18 Feb 2016 21:10:57 +0000 (16:10 -0500)]
sctp: Fix port hash table size computation
Dmitry Vyukov noted recently that the sctp_port_hashtable had an error in
its size computation, observing that the current method never guaranteed
that the hashsize (measured in number of entries) would be a power of two,
which the input hash function for that table requires. The root cause of
the problem is that two values need to be computed (one, the allocation
order of the storage requries, as passed to __get_free_pages, and two the
number of entries for the hash table). Both need to be ^2, but for
different reasons, and the existing code is simply computing one order
value, and using it as the basis for both, which is wrong (i.e. it assumes
that ((1<<order)*PAGE_SIZE)/sizeof(bucket) is still ^2 when its not).
To fix this, we change the logic slightly. We start by computing a goal
allocation order (which is limited by the maximum size hash table we want
to support. Then we attempt to allocate that size table, decreasing the
order until a successful allocation is made. Then, with the resultant
successful order we compute the number of buckets that hash table supports,
which we then round down to the nearest power of two, giving us the number
of entries the table actually supports.
I've tested this locally here, using non-debug and spinlock-debug kernels,
and the number of entries in the hashtable consistently work out to be
powers of two in all cases.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> CC: Dmitry Vyukov <dvyukov@google.com> CC: Vladislav Yasevich <vyasevich@gmail.com> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the problem that more CAN messages could be sent to the
interface as could be send on the CAN bus. This was more likely for slow baud
rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under
heavy TX load this produced another bulk transfer without checking the
free_slots variable and hence caused the overflow in the interface.
Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Linus Torvalds [Sat, 20 Feb 2016 17:32:40 +0000 (09:32 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"This is unusually large, partly due to the EFI fixes that prevent
accidental deletion of EFI variables through efivarfs that may brick
machines. These fixes are somewhat involved to maintain compatibility
with existing install methods and other usage modes, while trying to
turn off the 'rm -rf' bricking vector.
Other fixes are for large page ioremap()s and for non-temporal
user-memcpy()s"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix vmalloc_fault() to handle large pages properly
hpet: Drop stale URLs
x86/uaccess/64: Handle the caching of 4-byte nocache copies properly in __copy_user_nocache()
x86/uaccess/64: Make the __copy_user_nocache() assembly code more readable
lib/ucs2_string: Correct ucs2 -> utf8 conversion
efi: Add pstore variables to the deletion whitelist
efi: Make efivarfs entries immutable by default
efi: Make our variable validation list include the guid
efi: Do variable name validation tests in utf8
efi: Use ucs2_as_utf8 in efivarfs instead of open coding a bad version
lib/ucs2_string: Add ucs2 -> utf8 helper functions
Linus Torvalds [Sat, 20 Feb 2016 17:30:42 +0000 (09:30 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"A handful of CPU hotplug related fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Plug potential memory leak in CPU_UP_PREPARE
perf/core: Remove the bogus and dangerous CPU_DOWN_FAILED hotplug state
perf/core: Remove bogus UP_CANCELED hotplug state
perf/x86/amd/uncore: Plug reference leak
Linus Torvalds [Sat, 20 Feb 2016 17:22:11 +0000 (09:22 -0800)]
Merge tag 'powerpc-4.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix build error on 32-bit with checkpoint restart from Aneesh Kumar
- Fix dedotify for binutils >= 2.26 from Andreas Schwab
- Don't trace hcalls on offline CPUs from Denis Kirjanov
- eeh: Fix stale cached primary bus from Gavin Shan
- eeh: Fix stale PE primary bus from Gavin Shan
- mm: Fix Multi hit ERAT cause by recent THP update from Aneesh Kumar K.V
- ioda: Set "read" permission when "write" is set from Alexey Kardashevskiy
* tag 'powerpc-4.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/ioda: Set "read" permission when "write" is set
powerpc/mm: Fix Multi hit ERAT cause by recent THP update
powerpc/powernv: Fix stale PE primary bus
powerpc/eeh: Fix stale cached primary bus
powerpc/pseries: Don't trace hcalls on offline CPUs
powerpc: Fix dedotify for binutils >= 2.26
powerpc/book3s_32: Fix build error with checkpoint restart
Linus Torvalds [Sat, 20 Feb 2016 17:19:56 +0000 (09:19 -0800)]
Merge tag 'dmaengine-fix-4.5-rc5' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"A few fixes for drivers, nothing major here.
Fixes are: iotdma fix to restart channels, new ID for wildcat PCH,
residue fix for edma, disable irq for non-cyclic in dw"
* tag 'dmaengine-fix-4.5-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dw: disable BLOCK IRQs for non-cyclic xfer
dmaengine: edma: fix residue race for cyclic
dmaengine: dw: pci: add ID for WildcatPoint PCH
dmaengine: IOATDMA: fix timer code that continues to restart channels during idle
Linus Torvalds [Sat, 20 Feb 2016 17:16:51 +0000 (09:16 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk driver fixes from Stephen Boyd:
"An assortment of vendor specific clk drivers fixes, most notably
fallout from adding Tegra210 and rockchip rk3036/rk3368 drivers this
cycle.
There's also the random smattering of sparse/checker fixes, a build
"fix" to get the Tango clk driver to compile because the Kconfig
symbol was renamed after the fact, and a clk gpio fix for a patch
mismerge"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (28 commits)
clk: gpio: Really allow an optional clock= DT property
Revert "clk: qcom: Specify LE device endianness"
clk: versatile: mask VCO bits before writing
clk: tegra: super: Fix sparse warnings for functions not declared as static
clk: tegra: Fix sparse warnings for functions not declared as static
clk: tegra: Fix sparse warning for pll_m
clk: tegra: Use definition for pll_u override bit
clk: tegra: Fix warning caused by pll_u failing to lock
clk: tegra: Fix clock sources for Tegra210 EMC
clk: tegra: Add the APB2APE audio clock on Tegra210
clk: tegra: Add missing of_node_put()
clk: tegra: Fix PLLE SS coefficients
clk: tegra: Fix typos around clearing PLLE bits during enable
clk: tegra: Do not disable PLLE when under hardware control
clk: tegra: Fix pllx dyn step calculation
clk: tegra: pll: Fix potential sleeping-while-atomic
clk: tegra: Fix the misnaming of nvenc from msenc
clk: tegra: Fix naming of MISC registers
clk: tango4: rename ARCH_TANGOX to ARCH_TANGO
clk: scpi: Fix checking return value of platform_device_register_simple()
...
Linus Torvalds [Sat, 20 Feb 2016 17:13:18 +0000 (09:13 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull more drm fixes from Dave Airlie:
"Some more fixes trickled in:
A bunch of VC4 ones since it's a pretty new driver not much chance of
regressions, and it fixes GPU resets.
Also one atomic fix, one set of fixes for a common bug in TTM cleanup,
and one i915 hotplug fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: use post-decrement in error handling
drm/atomic: Allow for holes in connector state, v2.
drm/i915: Fix hpd live status bits for g4x
drm/vc4: Use runtime PM to power cycle the device when the GPU hangs.
drm/vc4: Enable runtime PM.
drm/vc4: Fix spurious GPU resets due to BO reuse.
drm/vc4: Drop error message on seqno wait timeouts.
drm/vc4: Fix -ERESTARTSYS error return from BO waits.
drm/vc4: Return an ERR_PTR from BO creation instead of NULL.
drm/vc4: Fix the clear color for the first tile rendered.
drm/vc4: Validate that WAIT_BO padding is cleared.
drm/radeon: use post-decrement in error handling
drm/amdgpu: use post-decrement in error handling
Simon Guinot [Wed, 9 Sep 2015 22:15:18 +0000 (00:15 +0200)]
kernel/resource.c: fix muxed resource handling in __request_region()
In __request_region, if a conflict with a BUSY and MUXED resource is
detected, then the caller goes to sleep and waits for the resource to be
released. A pointer on the conflicting resource is kept. At wake-up
this pointer is used as a parent to retry to request the region.
A first problem is that this pointer might well be invalid (if for
example the conflicting resource have already been freed). Another
problem is that the next call to __request_region() fails to detect a
remaining conflict. The previously conflicting resource is passed as a
parameter and __request_region() will look for a conflict among the
children of this resource and not at the resource itself. It is likely
to succeed anyway, even if there is still a conflict.
Instead, the parent of the conflicting resource should be passed to
__request_region().
As a fix, this patch doesn't update the parent resource pointer in the
case we have to wait for a muxed region right after.
Reported-and-tested-by: Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Tested-by: Vincent Donnefort <vdonnefort@gmail.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Douglas Anderson [Fri, 19 Feb 2016 22:25:21 +0000 (14:25 -0800)]
Bluetooth: hci_core: Avoid mixing up req_complete and req_complete_skb
In commit 44d271377479 ("Bluetooth: Compress the size of struct
hci_ctrl") we squashed down the size of the structure by using a union
with the assumption that all users would use the flag to determine
whether we had a req_complete or a req_complete_skb.
Unfortunately we had a case in hci_req_cmd_complete() where we weren't
looking at the flag. This can result in a situation where we might be
storing a hci_req_complete_skb_t in a hci_req_complete_t variable, or
vice versa.
During some testing I found at least one case where the function
hci_req_sync_complete() was called improperly because the kernel thought
that it didn't require an SKB. Looking through the stack in kgdb I
found that it was called by hci_event_packet() and that
hci_event_packet() had both of its locals "req_complete" and
"req_complete_skb" pointing to the same place: both to
hci_req_sync_complete().
Let's make sure we always check the flag.
For more details on debugging done, see <http://crbug.com/588288>.
Fixes: 44d271377479 ("Bluetooth: Compress the size of struct hci_ctrl") Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jaedon Shin [Fri, 19 Feb 2016 04:48:50 +0000 (13:48 +0900)]
net: bcmgenet: Fix internal PHY link state
The PHY link state is not chaged in GENETv2 caused by the previous
commit 49f7a471e4d1 ("net: bcmgenet: Properly configure PHY to ignore
interrupt") was set to PHY_IGNORE_INTERRUPT in bcmgenet_mii_probe().
The internal PHY should use phy_mac_interrupt() when not in use
PHY_POLL. The statement for phy_mac_interrupt() has two conditions. The
first condition to check GENET_HAS_MDIO_INTR is not related PHY link
state, so this patch removes it.
Fixes: 49f7a471e4d1 ("net: bcmgenet: Properly configure PHY to ignore interrupt") Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rainer Weikusat [Thu, 18 Feb 2016 12:39:46 +0000 (12:39 +0000)]
af_unix: Don't use continue to re-execute unix_stream_read_generic loop
The unix_stream_read_generic function tries to use a continue statement
to restart the receive loop after waiting for a message. This may not
work as intended as the caller might use a recvmsg call to peek at
control messages without specifying a message buffer. If this was the
case, the continue will cause the function to return without an error
and without the credential information if the function had to wait for a
message while it had returned with the credentials otherwise. Change to
using goto to restart the loop without checking the condition first in
this case so that credentials are returned either way.
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry V. Levin [Fri, 19 Feb 2016 01:27:48 +0000 (04:27 +0300)]
unix_diag: fix incorrect sign extension in unix_lookup_by_ino
The value passed by unix_diag_get_exact to unix_lookup_by_ino has type
__u32, but unix_lookup_by_ino's argument ino has type int, which is not
a problem yet.
However, when ino is compared with sock_i_ino return value of type
unsigned long, ino is sign extended to signed long, and this results
to incorrect comparison on 64-bit architectures for inode numbers
greater than INT_MAX.
This bug was found by strace test suite.
Fixes: 5d3cae8bc39d ("unix_diag: Dumping exact socket core") Signed-off-by: Dmitry V. Levin <ldv@altlinux.org> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sat, 20 Feb 2016 00:43:20 +0000 (19:43 -0500)]
bnxt_en: Remove unnecessary call to update PHY settings.
Fix bnxt_update_phy_setting() to check the correct parameters when
determining whether to update the PHY. Requested line speed/duplex should
only be checked for forced speed mode. This avoids unnecessary link
interruptions when loading the driver.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sat, 20 Feb 2016 00:43:19 +0000 (19:43 -0500)]
bnxt_en: Poll link at the end of __bnxt_open_nic().
When shutting down the NIC, we shutdown async event processing before
freeing all the rings. If there is a link change event during reset, the
driver may miss it and the link state may be incorrect after the NIC is
re-opened. Poll the link at the end of __bnxt_open_nic() to get the
correct link status.
Signed-off-by Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nishanth Menon [Sat, 20 Feb 2016 00:09:51 +0000 (18:09 -0600)]
hwmon: (gpio-fan) Remove un-necessary speed_index lookup for thermal hook
Thermal hook gpio_fan_get_cur_state is only interested in knowing
the current speed index that was setup in the system, this is
already available as part of fan_data->speed_index which is always
set by set_fan_speed. Using get_fan_speed_index is useful when we
have no idea about the fan speed configuration (for example during
fan_ctrl_init).
When thermal framework invokes
gpio_fan_get_cur_state=>get_fan_speed_index via gpio_fan_get_cur_state
especially in a polled configuration for thermal governor, we
basically hog the i2c interface to the extent that other functions
fail to get any traffic out :(.
Instead, just provide the last state set in the driver - since the gpio
fan driver is responsible for the fan state immaterial of override, the
fan_data->speed_index should accurately reflect the state.
Linus Torvalds [Fri, 19 Feb 2016 21:44:12 +0000 (13:44 -0800)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"Miscellaneous ext4 bug fixes for v4.5"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix crashes in dioread_nolock mode
ext4: fix bh->b_state corruption
ext4: fix memleak in ext4_readdir()
ext4: remove unused parameter "newblock" in convert_initialized_extent()
ext4: don't read blocks from disk after extents being swapped
ext4: fix potential integer overflow
ext4: add a line break for proc mb_groups display
ext4: ioctl: fix erroneous return value
ext4: fix scheduling in atomic on group checksum failure
ext4 crypto: move context consistency check to ext4_file_open()
ext4 crypto: revalidate dentry after adding or removing the key
Linus Torvalds [Fri, 19 Feb 2016 21:40:42 +0000 (13:40 -0800)]
Merge branch 'for-linus-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"My for-linus-4.5 branch has a btrfs DIO error passing fix.
I know how much you love DIO, so I'm going to suggest against reading
it. We'll follow up with a patch to drop the error arg from
dio_end_io in the next merge window."
* 'for-linus-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix direct IO requests not reporting IO error to user space
Linus Torvalds [Fri, 19 Feb 2016 21:36:00 +0000 (13:36 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge fixes from Andrew Morton:
"10 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: slab: free kmem_cache_node after destroy sysfs file
ipc/shm: handle removed segments gracefully in shm_mmap()
MAINTAINERS: update Kselftest Framework mailing list
devm_memremap_release(): fix memremap'd addr handling
mm/hugetlb.c: fix incorrect proc nr_hugepages value
mm, x86: fix pte_page() crash in gup_pte_range()
fsnotify: turn fsnotify reaper thread into a workqueue job
Revert "fsnotify: destroy marks with call_srcu instead of dedicated thread"
mm: fix regression in remap_file_pages() emulation
thp, dax: do not try to withdraw pgtable from non-anon VMA
Paul Bolle [Thu, 18 Feb 2016 20:29:08 +0000 (21:29 +0100)]
ser_gigaset: use container_of() instead of detour
The purpose of gigaset_device_release() is to kfree() the struct
ser_cardstate that contains our struct device. This is done via a bit of
a detour. First we make our struct device's driver_data point to the
container of our struct ser_cardstate (which is a struct cardstate). In
gigaset_device_release() we then retrieve that driver_data again. And
after that we finally kfree() the struct ser_cardstate that was saved in
the struct cardstate.
All of this can be achieved much easier by using container_of() to get
from our struct device to its container, struct ser_cardstate. Do so.
Note that at the time the detour was implemented commit b8b2c7d845d5
("base/platform: assert that dev_pm_domain callbacks are called
unconditionally") had just entered the tree. That commit disconnected
our platform_device and our platform_driver. These were reconnected
again in v4.5-rc2 through commit 25cad69f21f5 ("base/platform: Fix
platform drivers with no probe callback"). And one of the consequences
of that fix was that it broke the detour via driver_data. That's because
it made __device_release_driver() stop being a NOP for our struct device
and actually do stuff again. One of the things it now does, is setting
our driver_data to NULL. That, in turn, makes it impossible for
gigaset_device_release() to get to our struct cardstate. Which has the
net effect of leaking a struct ser_cardstate at every call of this
driver's tty close() operation. So using container_of() has the
additional benefit of actually working.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Tested-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Acked-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 19 Feb 2016 20:51:18 +0000 (15:51 -0500)]
Merge tag 'wireless-drivers-for-davem-2016-02-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
rtlwifi
* fix broken VHT (802.11ac) support, reported by Linus
wlcore
* fix firmware initialisation regression on wl1271
iwlwifi
* fix a race that users reported when we try to load the firmware
and the hardware rfkill interrupt triggers at the same time
* fix a very visible bug in scheduled scan: the firmware
doesn't support scheduled scan with no profile configured and
the supplicant sometimes requests such scheduled scans
* build system fix to be able to link iwlwifi statically into kernel
* firmware name update for 8265
* typo fix in return value
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steve Wise [Thu, 18 Feb 2016 14:34:24 +0000 (06:34 -0800)]
cxgb3: fix up vpd strings for kstrto*()
The vpd strings are left justified, in a fixed length array, with possible
trailing white space and no NUL. So fix them up before calling kstrto*().
This is a recent regression which causes cxgb3 to fail to load.
Fixes: e72c932 ("cxgb3: Convert simple_strtoul to kstrtox") Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 17 Feb 2016 18:30:01 +0000 (19:30 +0100)]
lwt: fix rx checksum setting for lwt devices tunneling over ipv6
the commit 35e2d1152b22 ("tunnels: Allow IPv6 UDP checksums to be
correctly controlled.") changed the default xmit checksum setting
for lwt vxlan/geneve ipv6 tunnels, so that now the checksum is not
set into external UDP header.
This commit changes the rx checksum setting for both lwt vxlan/geneve
devices created by openvswitch accordingly, so that lwt over ipv6
tunnel pairs are again able to communicate with default values.
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Jiri Benc <jbenc@redhat.com> Acked-by: Jesse Gross <jesse@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 19 Feb 2016 20:35:29 +0000 (15:35 -0500)]
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Two of the fixes included in this patchset prevent wrong memory
access - it was triggered when removing an object from a list
after it was already free'd due to bad reference counting.
This misbehaviour existed for both the gw_node and the
orig_node_vlan object and has been fixed by Sven Eckelmann.
The last patch fixes our interface feasibility check and prevents
it from looping indefinitely when two net_device objects
reference each other via iflink index (i.e. veth pair), by
Andrew Lunn
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Protopopov [Wed, 17 Feb 2016 02:43:16 +0000 (21:43 -0500)]
rtnl: RTM_GETNETCONF: fix wrong return value
An error response from a RTM_GETNETCONF request can return the positive
error value EINVAL in the struct nlmsgerr that can mislead userspace.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: make netdev_for_each_lower_dev safe for device removal
When I used netdev_for_each_lower_dev in commit bad531623253 ("vrf:
remove slave queue and private slave struct") I thought that it acts
like netdev_for_each_lower_private and can be used to remove the current
device from the list while walking, but unfortunately it acts more like
netdev_for_each_lower_private_rcu and doesn't allow it. The difference
is where the "iter" points to, right now it points to the current element
and that makes it impossible to remove it. Change the logic to be
similar to netdev_for_each_lower_private and make it point to the "next"
element so we can safely delete the current one. VRF is the only such
user right now, there's no change for the read-only users.
CC: David Ahern <dsa@cumulusnetworks.com> CC: David S. Miller <davem@davemloft.net> CC: Roopa Prabhu <roopa@cumulusnetworks.com> CC: Vlad Yasevich <vyasevic@redhat.com> Fixes: bad531623253 ("vrf: remove slave queue and private slave struct") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: David Ahern <dsa@cumulusnetworks.com> Tested-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 19 Feb 2016 16:40:05 +0000 (08:40 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here are some more arm64 fixes for 4.5. This has mostly come from
Yang Shi, who saw some issues under -rt that also affect mainline.
The rest of it is pretty small, but still worth having.
We've got an old issue outstanding with valid_user_regs which will
likely wait until 4.6 (since it would really benefit from some time in
-next) and another issue with kasan and idle which should be fixed
next week.
Apart from that, pretty quiet here (and still no sign of the THP issue
reported on s390...)
Summary:
- Allow EFI stub to use strnlen(), which is required by recent libfdt
- Avoid smp_processor_id() in preempt context during unwinding
- Avoid false Kasan warnings during unwinding
- Ensure early devices are picked up by the IOMMU DMA ops
- Avoid rebuilding the kernel for the 'install' target
- Run fixup handlers for alignment faults on userspace access"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: allow the kernel to handle alignment faults on user accesses
arm64: kbuild: make "make install" not depend on vmlinux
arm64: dma-mapping: fix handling of devices registered before arch_initcall
arm64/efi: Make strnlen() available to the EFI namespace
arm/arm64: crypto: assure that ECB modes don't require an IV
arm64: make irq_stack_ptr more robust
arm64: debug: re-enable irqs before sending breakpoint SIGTRAP
arm64: disable kasan when accessing frame->fp in unwind_frame
Linus Torvalds [Fri, 19 Feb 2016 16:33:12 +0000 (08:33 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Several bug fixes:
- There are four different stack tracers, and three of them have
bugs. For 4.5 the bugs are fixed and we prepare a cleanup patch
for the next merge window.
- Three bug fixes for the dasd driver in regard to parallel access
volumes and the new max_dev_sectors block device queue limit
- The irq restore optimization needs a fixup for memcpy_real
- The diagnose trace code has a conflict with lockdep"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/dasd: fix performance drop
s390/maccess: reduce stnsm instructions
s390/diag: avoid lockdep recursion
s390/dasd: fix refcount for PAV reassignment
s390/dasd: prevent incorrect length error under z/VM after PAV changes
s390: fix DAT off memory access, e.g. on kdump
s390/oprofile: fix address range for asynchronous stack
s390/perf_event: fix address range for asynchronous stack
s390/stacktrace: add save_stack_trace_regs()
s390/stacktrace: save full stack traces
s390/stacktrace: add missing end marker
s390/stacktrace: fix address ranges for asynchronous and panic stack
s390/stacktrace: fix save_stack_trace_tsk() for current task
Linus Torvalds [Fri, 19 Feb 2016 16:25:40 +0000 (08:25 -0800)]
Merge tag 'pinctrl-v4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull Pin control fixes from Linus Walleij:
"Pin control fixes for the v4.5 series, all are individual driver
fixes:
- Fix the PXA2xx driver to export its init function so we do not
break modular compiles.
- Hide unused functions in the Nomadik driver.
- Fix up direction control in the Mediatek driver.
- Toggle the sunxi GPIO lines to input when you read them on the H3
GPIO controller, lest you only get garbage.
- Fix up the number of settings in the MVEBU driver.
- Fix a serious SMP race condition in the Samsung driver"
* tag 'pinctrl-v4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: samsung: fix SMP race condition
pinctrl: mvebu: fix num_settings in mpp group assignment
pinctrl: sunxi: H3 requires irq_read_needs_mux
pinctrl: mediatek: fix direction control issue
pinctrl: nomadik: hide unused functions
pinctrl: pxa: export pxa2xx_pinctrl_init()
Linus Torvalds [Fri, 19 Feb 2016 16:01:41 +0000 (08:01 -0800)]
Merge tag 'sound-4.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This update contains again a few more fixes for ALSA core stuff
although it's no longer high flux: two race fixes in sequencer and one
PCM race fix for non-atomic PCM ops.
In addition, HD-audio gained a similar fix for race at reloading the
driver"
* tag 'sound-4.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pcm: Fix rwsem deadlock for non-atomic PCM stream
ALSA: seq: Fix double port list deletion
ALSA: hda - Cancel probe work instead of flush at remove
ALSA: seq: Fix leak of pool buffer at concurrent writes
EunTaik Lee [Tue, 16 Feb 2016 04:44:35 +0000 (04:44 +0000)]
arm64: mm: allow the kernel to handle alignment faults on user accesses
Although we don't expect to take alignment faults on access to normal
memory, misbehaving (i.e. buggy) user code can pass MMIO pointers into
system calls, leading to things like get_user accessing device memory.
Rather than OOPS the kernel, allow any exception fixups to run and
return something like -EFAULT back to userspace. This makes the
behaviour more consistent with userspace, even though applications with
access to device mappings can easily cause other issues if they try
hard enough.
Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Eun Taik Lee <eun.taik.lee@samsung.com>
[will: dropped __kprobes annotation and rewrote commit mesage] Signed-off-by: Will Deacon <will.deacon@arm.com>
Masahiro Yamada [Fri, 19 Feb 2016 06:05:50 +0000 (15:05 +0900)]
arm64: kbuild: make "make install" not depend on vmlinux
For the same reason as commit 19514fc665ff ("arm, kbuild: make "make
install" not depend on vmlinux"), the install targets should never
trigger the rebuild of the kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Jan Kara [Fri, 19 Feb 2016 05:33:21 +0000 (00:33 -0500)]
ext4: fix crashes in dioread_nolock mode
Competing overwrite DIO in dioread_nolock mode will just overwrite
pointer to io_end in the inode. This may result in data corruption or
extent conversion happening from IO completion interrupt because we
don't properly set buffer_defer_completion() when unlocked DIO races
with locked DIO to unwritten extent.
Since unlocked DIO doesn't need io_end for anything, just avoid
allocating it and corrupting pointer from inode for locked DIO.
A cleaner fix would be to avoid these games with io_end pointer from the
inode but that requires more intrusive changes so we leave that for
later.
Cc: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Jan Kara [Fri, 19 Feb 2016 05:18:25 +0000 (00:18 -0500)]
ext4: fix bh->b_state corruption
ext4 can update bh->b_state non-atomically in _ext4_get_block() and
ext4_da_get_block_prep(). Usually this is fine since bh is just a
temporary storage for mapping information on stack but in some cases it
can be fully living bh attached to a page. In such case non-atomic
update of bh->b_state can race with an atomic update which then gets
lost. Usually when we are mapping bh and thus updating bh->b_state
non-atomically, nobody else touches the bh and so things work out fine
but there is one case to especially worry about: ext4_finish_bio() uses
BH_Uptodate_Lock on the first bh in the page to synchronize handling of
PageWriteback state. So when blocksize < pagesize, we can be atomically
modifying bh->b_state of a buffer that actually isn't under IO and thus
can race e.g. with delalloc trying to map that buffer. The result is
that we can mistakenly set / clear BH_Uptodate_Lock bit resulting in the
corruption of PageWriteback state or missed unlock of BH_Uptodate_Lock.
Fix the problem by always updating bh->b_state bits atomically.
CC: stable@vger.kernel.org Reported-by: Nikolay Borisov <kernel@kyup.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Rasmus Villemoes [Mon, 15 Feb 2016 18:41:46 +0000 (19:41 +0100)]
drm/nouveau: use post-decrement in error handling
We need to use post-decrement to get the dma_map_page undone also for
i==0, and to avoid some very unpleasant behaviour if dma_map_page
failed already at i==0.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Reviewed-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
drm/atomic: Allow for holes in connector state, v2.
Because we record connector_mask using 1 << drm_connector_index now
the connector_mask should stay the same even when other connectors
are removed. This was not the case with MST, in that case when removing
a connector all other connectors may change their index.
This is fixed by waiting until the first get_connector_state to allocate
connector_state, and force reallocation when state is too small.
As a side effect connector arrays no longer have to be preallocated,
and can be allocated on first use which means a less allocations in
the page flip only path.
Changes since v1:
- Whitespace. (Ville)
- Call ida_remove when destroying the connector. (Ville)
- u32 alloc -> int. (Ville)
Fixes: 14de6c44d149 ("drm/atomic: Remove drm_atomic_connectors_for_crtc.") Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Lyude <cpaul@redhat.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Stephen Boyd [Fri, 19 Feb 2016 03:07:44 +0000 (19:07 -0800)]
clk: gpio: Really allow an optional clock= DT property
We mis-merged the original patch from Russell here and so the
patch went almost all the way, except that we still failed to
probe when there wasn't a clocks property in the DT node. Allow
that case by making a negative value from
of_clk_get_parent_count() into "no parents", like the original
patch did.
Fixes: 7ed88aa2efa5 ("clk: fix clk-gpio.c with optional clock= DT property") Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Michael Turquette <mturquette@baylibre.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Dave Airlie [Fri, 19 Feb 2016 02:50:00 +0000 (12:50 +1000)]
Merge tag 'drm-vc4-fixes-2016-02-17' of github.com:anholt/linux into drm-fixes
This pull request fixes GPU reset (which was disabled shortly after
V3D integration due to build breakage) and waits for idle in the
presence of signals (which X likes to do a lot).
* tag 'drm-vc4-fixes-2016-02-17' of github.com:anholt/linux:
drm/vc4: Use runtime PM to power cycle the device when the GPU hangs.
drm/vc4: Enable runtime PM.
drm/vc4: Fix spurious GPU resets due to BO reuse.
drm/vc4: Drop error message on seqno wait timeouts.
drm/vc4: Fix -ERESTARTSYS error return from BO waits.
drm/vc4: Return an ERR_PTR from BO creation instead of NULL.
drm/vc4: Fix the clear color for the first tile rendered.
drm/vc4: Validate that WAIT_BO padding is cleared.
Dave Airlie [Fri, 19 Feb 2016 02:49:03 +0000 (12:49 +1000)]
Merge branch 'drm-fixes-4.5' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Just two small fixes in the ttm_tt_populate error handling; one for radeon,
one for amdgpu.
* 'drm-fixes-4.5' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: use post-decrement in error handling
drm/amdgpu: use post-decrement in error handling
Linus Torvalds [Fri, 19 Feb 2016 00:34:15 +0000 (16:34 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching
Pull livepatching fixes from Jiri Kosina:
- regression (from 4.4) fix for ordering issue, introduced by an
earlier ftrace change, that broke live patching of modules.
The fix replaces the ftrace module notifier by direct call in order
to make the ordering guaranteed and well-defined. The patch, from
Jessica Yu, has been acked both by Steven and Rusty
- error message fix from Miroslav Benes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
ftrace/module: remove ftrace module notifier
livepatch: change the error message in asm/livepatch.h header files
Linus Torvalds [Fri, 19 Feb 2016 00:24:48 +0000 (16:24 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two simple fixes.
One prevents a soft lockup on some target removal scenarios and the
other prevents us trying to probe the marvell console device, which
causes it to time out and need the bus resetting"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fix soft lockup in scsi_remove_target() on module removal
SCSI: Add Marvell configuration device to VPD blacklist
Dmitry Safonov [Wed, 17 Feb 2016 21:11:37 +0000 (13:11 -0800)]
mm: slab: free kmem_cache_node after destroy sysfs file
When slub_debug alloc_calls_show is enabled we will try to track
location and user of slab object on each online node, kmem_cache_node
structure and cpu_cache/cpu_slub shouldn't be freed till there is the
last reference to sysfs file.
Separated __kmem_cache_release from __kmem_cache_shutdown which now
called on slab_kmem_cache_release (after the last reference to sysfs
file object has dropped).
Reintroduced locking in free_partial as sysfs file might access cache's
partial list after shutdowning - partial revert of the commit 69cb8e6b7c29 ("slub: free slabs without holding locks"). Zap
__remove_partial and use remove_partial (w/o underscores) as
free_partial now takes list_lock which s partial revert for commit 1e4dd9461fab ("slub: do not assert not having lock in removing freed
partial")
Signed-off-by: Dmitry Safonov <dsafonov@virtuozzo.com> Suggested-by: Vladimir Davydov <vdavydov@virtuozzo.com> Acked-by: Vladimir Davydov <vdavydov@virtuozzo.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ipc/shm: handle removed segments gracefully in shm_mmap()
remap_file_pages(2) emulation can reach file which represents removed
IPC ID as long as a memory segment is mapped. It breaks expectations of
IPC subsystem.
Test case (rewritten to be more human readable, originally autogenerated
by syzkaller[1]):
The pmem driver calls devm_memremap() to map a persistent memory range.
When the pmem driver is unloaded, this memremap'd range is not released
so the kernel will leak a vma.
Fix devm_memremap_release() to handle a given memremap'd address
properly.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Matthew Wilcox <willy@linux.intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vaishali Thakkar [Wed, 17 Feb 2016 21:11:26 +0000 (13:11 -0800)]
mm/hugetlb.c: fix incorrect proc nr_hugepages value
Currently incorrect default hugepage pool size is reported by proc
nr_hugepages when number of pages for the default huge page size is
specified twice.
When multiple huge page sizes are supported, /proc/sys/vm/nr_hugepages
indicates the current number of pre-allocated huge pages of the default
size. Basically /proc/sys/vm/nr_hugepages displays default_hstate->
max_huge_pages and after boot time pre-allocation, max_huge_pages should
equal the number of pre-allocated pages (nr_hugepages).
Test case:
Note that this is specific to x86 architecture.
Boot the kernel with command line option 'default_hugepagesz=1G
hugepages=X hugepagesz=2M hugepages=Y hugepagesz=1G hugepages=Z'. After
boot, 'cat /proc/sys/vm/nr_hugepages' and 'sysctl -a | grep hugepages'
returns the value X. However, dmesg output shows that Z huge pages were
pre-allocated.
So, the root cause of the problem here is that the global variable
default_hstate_max_huge_pages is set if a default huge page size is
specified (directly or indirectly) on the command line. After the command
line processing in hugetlb_init, if default_hstate_max_huge_pages is set,
the value is assigned to default_hstae.max_huge_pages. However,
default_hstate.max_huge_pages may have already been set based on the
number of pre-allocated huge pages of default_hstate size.
The solution to this problem is if hstate->max_huge_pages is already set
then it should not set as a result of global max_huge_pages value.
Basically if the value of the variable hugepages is set multiple times on
a command line for a specific supported hugepagesize then proc layer
should consider the last specified value.
Signed-off-by: Vaishali Thakkar <vaishali.thakkar@oracle.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Hillf Danton <hillf.zj@alibaba-inc.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Wed, 17 Feb 2016 21:11:23 +0000 (13:11 -0800)]
mm, x86: fix pte_page() crash in gup_pte_range()
Commit 3565fce3a659 ("mm, x86: get_user_pages() for dax mappings") has
moved up the pte_page(pte) in x86's fast gup_pte_range(), for no
discernible reason: put it back where it belongs, after the pte_flags
check and the pfn_valid cross-check.
That may be the cause of the NULL pointer dereference in
gup_pte_range(), seen when vfio called vaddr_get_pfn() when starting a
qemu-kvm based VM.
Signed-off-by: Hugh Dickins <hughd@google.com> Reported-by: Michael Long <Harn-Solo@gmx.de> Tested-by: Michael Long <Harn-Solo@gmx.de> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Layton [Wed, 17 Feb 2016 21:11:21 +0000 (13:11 -0800)]
fsnotify: turn fsnotify reaper thread into a workqueue job
We don't require a dedicated thread for fsnotify cleanup. Switch it
over to a workqueue job instead that runs on the system_unbound_wq.
In the interest of not thrashing the queued job too often when there are
a lot of marks being removed, we delay the reaper job slightly when
queueing it, to allow several to gather on the list.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com> Tested-by: Eryu Guan <guaneryu@gmail.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Eric Paris <eparis@parisplace.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Layton [Wed, 17 Feb 2016 21:11:18 +0000 (13:11 -0800)]
Revert "fsnotify: destroy marks with call_srcu instead of dedicated thread"
This reverts commit c510eff6beba ("fsnotify: destroy marks with
call_srcu instead of dedicated thread").
Eryu reported that he was seeing some OOM kills kick in when running a
testcase that adds and removes inotify marks on a file in a tight loop.
The above commit changed the code to use call_srcu to clean up the
marks. While that does (in principle) work, the srcu callback job is
limited to cleaning up entries in small batches and only once per jiffy.
It's easily possible to overwhelm that machinery with too many call_srcu
callbacks, and Eryu's reproduer did just that.
There's also another potential problem with using call_srcu here. While
you can obviously sleep while holding the srcu_read_lock, the callbacks
run under local_bh_disable, so you can't sleep there.
It's possible when putting the last reference to the fsnotify_mark that
we'll end up putting a chain of references including the fsnotify_group,
uid, and associated keys. While I don't see any obvious ways that that
could occurs, it's probably still best to avoid using call_srcu here
after all.
This patch reverts the above patch. A later patch will take a different
approach to eliminated the dedicated thread here.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com> Reported-by: Eryu Guan <guaneryu@gmail.com> Tested-by: Eryu Guan <guaneryu@gmail.com> Cc: Jan Kara <jack@suse.com> Cc: Eric Paris <eparis@parisplace.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The reason is that remap_file_pages() emulation assumes that the target
vma covers whole area we want to over map. That assumption is broken by
first remap_file_pages() call: it split the area into two vma.
The solution is to check next adjacent vmas, if they map the same file
with the same flags.
thp, dax: do not try to withdraw pgtable from non-anon VMA
DAX doesn't deposit pgtables when it maps huge pages: nothing to
withdraw. It can lead to crash.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Matthew Wilcox <willy@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Wed, 17 Feb 2016 22:25:11 +0000 (23:25 +0100)]
USB: cdc_subset: only build when one driver is enabled
This avoids a harmless randconfig warning I get when USB_NET_CDC_SUBSET
is enabled, but all of the more specific drivers are not:
drivers/net/usb/cdc_subset.c:241:2: #warning You need to configure some hardware for this driver
The current behavior is clearly intentional, giving a warning when
a user picks a configuration that won't do anything good. The only
reason for even addressing this is that I'm getting close to
eliminating all 'randconfig' warnings on ARM, and this came up
a couple of times.
My workaround is to not even build the module when none of the
configurations are enable.
Alternatively we could simply remove the #warning (nothing wrong
for compile-testing), turn it into a runtime warning, or
change the Kconfig options into a menu to hide CONFIG_USB_NET_CDC_SUBSET.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Tue, 16 Feb 2016 21:18:26 +0000 (22:18 +0100)]
vxlan: do not use fdb in metadata mode
In metadata mode, the vxlan interface is not supposed to use the fdb control
plane but an external one (openvswitch or static routes). With the current
code, packets may leak into the fdb handling code which usually causes them
to be dropped anyway but may have strange side effects.
Just drop the packets directly when in metadata mode if the destination data
are not correctly provided on egress.
Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Protopopov [Wed, 17 Feb 2016 16:19:56 +0000 (11:19 -0500)]
mISDN: prevent possible NULL pointer dereference
A return value of the bchannel_get_rxbuf() function is compared with the
positive ENOMEM value instead of the negative -ENOMEM value to detect a
memory allocation problem. Thus, after a possible memory allocation
failure the bc->bch.rx_skb will be NULL which will lead to a NULL
pointer dereference.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log