Jan Kiszka [Tue, 21 Apr 2015 05:18:27 +0000 (07:18 +0200)]
ARM: Factor out reusable psci_cpu_off_common
Move parts of sunxi's psci_cpu_off into psci_cpu_off_common, namely
cache disabling and flushing, clrex and the disabling of SMP for the
dying CPU. These steps are apparently generic for ARMv7 and will be
reused for Tegra124 support.
As the way of disabled SMP is not architectural, though commonly done
via ACLTR, the related function can be overloaded.
CC: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Tested-by: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Tom Warren <twarren@nvidia.com>
Jan Kiszka [Tue, 21 Apr 2015 05:18:26 +0000 (07:18 +0200)]
ARM: Factor out common psci_get_cpu_id
Will be required for obtaining the ID of the current CPU in shared PSCI
functions. The default implementation requires a dense ID space and only
supports a single cluster. Therefore, the functions can be overloaded in
cases where these assumptions do not hold.
CC: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Tested-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Tom Warren <twarren@nvidia.com>
Jan Kiszka [Tue, 21 Apr 2015 05:18:24 +0000 (07:18 +0200)]
ARM: Clean up CONFIG_ARMV7_NONSEC/VIRT/PSCI conditions
CONFIG_ARMV7_VIRT depends on CONFIG_ARMV7_NONSEC, thus doesn't need to
be taken into account additionally. CONFIG_ARMV7_PSCI is only set on
boards that support CONFIG_ARMV7_NONSEC, and it only works on those.
CC: Tang Yuantian <Yuantian.Tang@freescale.com> CC: York Sun <yorksun@freescale.com> CC: Steve Rae <srae@broadcom.com> CC: Andre Przywara <andre.przywara@linaro.org> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Tested-by: Alison Wang <alison.wang@freescale.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Tue, 14 Apr 2015 14:41:14 +0000 (08:41 -0600)]
ARM: tegra: enable STDIO deregistration
At the very least when USB keyboard support is enabled, we need to enable
CONFIG_SYS_STDIO_DEREGISTER, so the "usb reset" is able to re-scan USB
ports and find new devices. Enable it everywhere per request from Simon
Glass.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
As best I can tell, CONFIG_SYS_LOAD_ADDR and CONFIG_LOADADDR/$loadaddr
serve essentially the same purpose. Roughly, if a command takes a load
address, then CONFIG_SYS_LOAD_ADDR or $loadaddr (or both) are the default
if the command-line does not specify the address. Different U-Boot
commands are inconsistent re: which of the two default values they use.
As such, set the two to the same value, and move the logic that does this
into tegra-common-post.h so it's not duplicated. A number of other non-
Tegra boards do this too.
The values chosen for these macros are no longer consistent with anything
in MEM_LAYOUT_ENV_SETTINGS. Regain consistency by setting $kernel_addr_r
to CONFIG_LOADADDR. Older scripts tend to use $loadaddr for the default
kernel load address, whereas newer scripts and features tend to use
$kernel_addr_r, along with other variables for other purposes such as
DTBs and initrds. Hence, it's logical they should share the same value.
I had originally thought to make the $kernel_addr_r and CONFIG_LOADADDR
have different values. This would guarantee no interference if a script
used the two variables for different purposes. However, that scenario is
unlikely given the semantic meaning associated with the two variables.
The lowest available value is 0x90200000; see comments for
MEM_LAYOUT_ENV_SETTINGS in tegra30-common-post.h for details. However,
that value would be problematic for a script that loaded a raw zImage to
$loadaddr, since it's more than 128MB beyond the start of SDRAM, which
would interfere with the kernel's CONFIG_AUTO_ZRELADDR. So, let's not do
that.
The only potential fallout I could foresee from this patch is if someone
has a script that loads the kernel to $loadaddr, but some other file
(DTB, initrd) to a hard-coded address that the new value of $loadaddr
interferes with. This seems unlikely. A user should not do that; they
should either hard-code all load addresses, or use U-Boot-supplied
variables for all load addresses. Equally, any fallout due to this change
is trivial to fix; simply modify the load addresses in that script.
Cc: Paul Walmsley <pwalmsley@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Paul Walmsley <pwalmsley@nvidia.com> Reviewed-by: Simon Glass Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 15 Apr 2015 03:03:41 +0000 (21:03 -0600)]
tegra: video: Add Embedded DisplayPort driver
This interface is used on laptop devices based on Tegra. Add a driver which
provides access to the eDP interface. The driver uses the display port
uclass.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 15 Apr 2015 03:03:33 +0000 (21:03 -0600)]
tegra: clock: Split the clock source code into a separate function
Create a function which sets the source clock for a peripheral, given
the number of mux bits to adjust. This can then be used more generally.
For now, don't export it.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 15 Apr 2015 03:03:32 +0000 (21:03 -0600)]
tegra: clock: Add checking for invalid clock IDs
The get_pll() function can do the wrong thing if passed values that are
out of range. Add checks for this and add a function which can return
a 'simple' PLL. This can be defined by SoCs with their own clocks.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 15 Apr 2015 03:03:20 +0000 (21:03 -0600)]
dm: gpio: Add error handling and a function to claim vector GPIOs
gpio_get_values_as_int() should return an error if something goes wrong.
Also provide gpio_claim_vector(), a function to request the GPIOs and set
them to input mode. Otherwise callers have to do this themselves.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Joe Hershberger [Tue, 12 May 2015 19:46:24 +0000 (14:46 -0500)]
Clean all defconfigs with savedefconfig
In order to reduce merge conflicts and to maintain the simplest possible
defconfig files, we should be using the savedefconfig feature of Kconfig
every time a new feature is added. This keeps the defconfig settings to
a minimum (only those things not default) and keeps them in the same
order as the Kconfig options.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Cc: Tom Rini <trini@konsulko.com>
Joe Hershberger [Tue, 12 May 2015 19:46:23 +0000 (14:46 -0500)]
arch: Make board selection choices optional
By making the board selections optional, every defconfig will include
the board selection when running savedefconfig so if a new board is
added to the top of the list of choices the former top's defconfig will
still be correct.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Cc: Tom Rini <trini@konsulko.com>
Stefan Roese [Thu, 7 May 2015 11:00:23 +0000 (13:00 +0200)]
ppc4xx: Remove sc3 board
As this board seems to be unmaintained for quite some time, and its
not moved to the generic board ingrastructure, lets remove it.
This will also enable us to remove the CONFIG_AUTOBOOT_DELAY_STR2
and CONFIG_AUTOBOOT_STOP_STR2 macros, as this sc3 board is the
only one using one of this macros. A removal patch will follow
soon.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Juergen Beisert <jbeisert@eurodsn.de> Acked-by: Heiko Schocher <hs@denx.de>
The crc32 command with no -v expects an optional 3rd argument to be an
address to store the result in. With the -v switch, the last argument
is a crc, not an address. In the case where -v is set, we should set the
HASH_FLAG_ENV flag since that will first look for the value to be a
digest value, which matches the expected API for the crc32 command.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Vikas Manocha [Sun, 3 May 2015 21:10:34 +0000 (14:10 -0700)]
stv0991: fdt: add stv0991 device tree
This patch adds device tree for the ST Micro stv0991 board & enables
device tree control. Progressively device tree support for the drivers
being used will also be added.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
This is because the gd pointer is not set early enough anymore,
such that the i2c_set_bus_num in get_board_revision can safely
execute. This results in a console hang at SPL and the boot does
not proceed.
This piece of code is anyway necessary only for really old Overo
boards with revision numbers <= 2410 and not required for the newer
boards. For these older boards, u-boot v2014.10 still works fine.
overo: Split overo.c into spl.c, common.c and overo.c
This separates the SPL-specific code from the u-boot-specific code for
the Overo board following the discussion at
http://lists.denx.de/pipermail/u-boot/2015-April/211622.html
The code is split up into spl.c, overo.c and common.c (which
has the code common to both)
Ash Charles [Tue, 28 Apr 2015 23:17:54 +0000 (16:17 -0700)]
omap3: overo: Allow boot with kernel in UBI rootfs
If regular NAND booting fails to find a valid uImage in the
kernel partition in NAND, try to boot using a zImage and dtb found
in a UBI volume in the rootfs partition. This is the NAND analog
of mmc zImage booting for device-tree based kernels.
Signed-off-by: Ash Charles <ashcharles@gmail.com> Signed-off-by: Arun Bharadwaj <arun@gumstix.com>
Ash Charles [Tue, 28 Apr 2015 23:17:53 +0000 (16:17 -0700)]
omap3: overo: Use software BCH8 ECC for NAND
Overo COMs have NAND flash that requires 4-bit ECC or better except for
the first sector which can use 1-bit ECC. The boot ROM expects to load
a payload from NAND written using 1-bit hardware-based ECC. In short,
write SPL to NAND something like this (4 times for redundancy):
#> nandecc hw
#> nand write ${loadaddr} 0x0 ${filesize}
#> nand write ${loadaddr} 0x20000 ${filesize}
#> nand write ${loadaddr} 0x40000 ${filesize}
#> nand write ${loadaddr} 0x60000 ${filesize}
Then, switch back to software-based BCH8 for everything else:
#> nandecc sw bch8
After [1], enlarge the max size of the SPL so the BCH code can fit.
Add the stm32F4 board's serial ports support.
User can use it easily.
The user only need to edit the number of the usart.
The patch also fix the serial print out.
Last, this version of patch fix the first patch checkpatch.pl error.
Thanks to Kamil Lulko.
spl: spl_mmc: Clearer structure in spl_mmc_load_image and cosmetics
This refactors spl_mmc_load_image to use a switch/case structure and easier
to understand spl_start_uboot checks. This also introduces some more automatic
fallback on the next mmc boot mode as long as it keeps failing.
Lines that go beyond 80 chars are also reduced by reducing the number of tabs.
Debug and error strings are refctored to match a common style.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
[trini: Fix a thinko in the SPL_EXT_SUPPORT + SPL_OS conversion, make part be
__maybe_unused] Signed-off-by: Tom Rini <trini@konsulko.com>
Since the used AM3352 SoC doesn't have GPU it isn't allways necessary to build
in complete drm-stuff into linux kernel. In very small applications only we use
the simple-framebuffer.
So we have 2 use-cases:
- device operating on drm-driver (let simplefb node disabled)
- device operating on simplefb-driver (activate simplefb node and reserve mem)
The decision is made by means of "simplefb" environment variable.
simplefb = 0
we don't enable the (maybe) existing simplefb node and all the rest around
display is up to the linux-kernel. We just disable the backlight, beceause we
do not want see the flicker during take over of drm-driver.
simplefb = 1
we enable the (maybe) existing simplefb node and reserve framebuffers size
in memory.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
the CONFIG_LCD_NOSTDOUT feature never had become mainline in uboot due to the
fact that the problem of "not writing out whole console to lcd" can be solved
with another way.
So we remove this unnary define.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
board/BuR/tseries: take usage of CONFIG_LCD_ROTATION
We take use of the new LCD_ROTATION feature.
The information about how the display is rotated is taken from B&R specific
(/factory-settings/rotation) information in the devicetree.
The information there is stored as string (cw, ud, ccw, none) since starting
support of this devices and cannot be changed, so we have to convert it into
none = 0
cw = 1
ud = 2
ccw = 3
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Maxime Ripard [Fri, 24 Apr 2015 10:53:12 +0000 (12:53 +0200)]
image: android: handle default kernel address
The two tools that create android boot images, mkbootimg and the fastboot
client, set the kernel address by default to 0x10008000.
U-boot always honors this field, and will try to relocate the kernel to
whatever value is set in the header, which won't be mapped to the actual RAM on
most platforms, resulting in the kernel obviously not booting.
All the targets in U-Boot right now will download the android boot image to
CONFIG_SYS_LOAD_ADDR, which means that it will already have been downloaded to
some location that is suitable for execution.
In order to have the kernel booting even with the default boot image kernel
address, if that address is used, just execute the kernel where it is.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch fixes cross-compiling U-Boot tools with the musl C library:
* including <sys/types.h> is needed for ulong
* defining _GNU_SOURCE is needed for loff_t
Tested for target at91sam9261ek_dataflash_cs3.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks> Cc: Tom Rini <trini@konsulko.com>
Across several devices network environment variables are duplicated.
Move these variables to a common include file which insures the environment
variables are reused and insures devices across product lines share the same
values.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
ARM: socfpga: move board select into mach-socfpga/Kconfig
Switch to a more standard way of board select; put the SoC select
into arch/arm/Kconfig and move the board select menu under
arch/arm/mach-socfpga/Kconfig.
Because all the SOCFPGA boards define CONFIG_SPL_FRAMEWORK
(see include/configs/socfpga_common.h), u-boot.img is automatically
added to the target image list by the top Makefile.
For the distro_bootcmds to succeed on the sandbox a bit of setup is
required (e.g. network configured or host image bound), so running them
by default isn't that useful.
Add a -b/--boot command to the sandbox binary, which triggers the
distro_bootcmds to run after the other command-line commands.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Acked-by: Simon Glass <sjg@chromium.org>
Hans de Goede [Tue, 5 May 2015 21:56:08 +0000 (23:56 +0200)]
usb: ohci: Move the ohci_dev struct to inside the main ohci struct
This is a preparation patch for adding driver-model support.
Note we do keep ohci_dev as a separate struct so that we can later add
support for interrupt-queues which requires allocating a separate ohci_dev
per interrupt-queue.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Marek Vasut <marex@denx.de>
Hans de Goede [Tue, 5 May 2015 09:54:34 +0000 (11:54 +0200)]
dm: usb: Fix finding of first upstream usb-2 hub in the ehci dm code
The ehci driver model code for finding the first upstream usb-2 hub before
this commit has a number of issues:
1) "if (!ttdev->speed != USB_SPEED_HIGH)" does not work because the '!'
takes presedence over the '!=' this should simply be
"if (ttdev->speed == USB_SPEED_HIGH)"
2) It makes ttdev point to the first upstream usb-2 hub, but ttdev should
point to the last usb-1 device before the first usb-2 hub (when going
upstream from the device), as ttdev is used to find the port of the
first usb-2 hub to which the the last usb-1 device is connected.
3) parent_devnum however should be set to the devnum of the first usb-2
hub, so we need to keep pointers around to both usb_device structs.
To complicate things further during enumeration usb_device.dev will point
to the parent udevice, where as during normal use it will point to
the actual udevice, we must handle both cases correctly.
This commit fixes all this making usb-1 devices attached to usb-2 hubs,
including usb-1 devices attached to usb-1 hubs attached to usb-2 hubs, work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Simon Glass <sjg@chromium.org>
Hans de Goede [Tue, 5 May 2015 09:54:32 +0000 (11:54 +0200)]
dm: usb: Copy over usb_device values from usb_scan_device() to final usb_device
Currently we copy over a number of usb_device values stored in the on stack
struct usb_device probed in usb_scan_device() to the final driver-model managed
struct usb_device in usb_child_pre_probe() through usb_device_platdata, and
then call usb_select_config() to fill in the rest.
There are 3 problems with this approach:
1) It does not fill in enough fields before calling usb_select_config(),
specifically it does not fill in ep0's maxpacketsize causing a div by zero
exception in the ehci driver.
2) It unnecessarily redoes a number of usb requests making usb probing slower
3) Calling usb_select_config() a second time fails on some usb-1 devices
plugged into usb-2 hubs, causing u-boot to not recognize these devices.
This commit fixes these issues by removing (*) the usb_select_config() call
from usb_child_pre_probe(), and instead of copying over things field by field
through usb_device_platdata, store a pointer to the in stack usb_device
(which is still valid when usb_child_pre_probe() gets called) and copy
over the entire struct.
*) Except for devices which are explictly instantiated through device-tree
rather then discovered through usb_scan_device() such as emulated usb devices
in the sandbox.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Simon Glass <sjg@chromium.org>
Hans de Goede [Mon, 4 May 2015 19:33:26 +0000 (21:33 +0200)]
dm: usb: Do not use bus->seq before device_probe(bus)
Do not use bus->seq before device_probe(bus), as bus->seq is not set until
after the device_probe() call. This fixes u-boot printing: "USB-1: " for
each bus it scans.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Simon Glass <sjg@chromium.org>
dm_gpio_set_dir_flags() will also set gpio output value when switching to
gpio output. So it's not necessary to call dm_gpio_set_value() after
dm_gpio_set_dir_flags() call.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Simon Glass <sjg@chromium.org>
projects / karo-tx-uboot.git / log