Randy Dunlap [Thu, 11 Mar 2010 17:10:32 +0000 (09:10 -0800)]
mtd/nand/r852: fix build for CONFIG_PCI disabled
r852 fails to build when CONFIG_PCI is not enabled since it uses
pci_*() calls and is a PCI driver, so it should depend on PCI
to prevent build errors.
It should also #include <linux/pci.h>.
drivers/mtd/nand/r852.c:1053: error: implicit declaration of function 'pci_prepare_to_sleep'
drivers/mtd/nand/r852.c:1062: error: implicit declaration of function 'pci_back_from_sleep'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Tue, 9 Mar 2010 02:45:00 +0000 (18:45 -0800)]
mtd: Make SM_FTL depend on MTD_NAND
Randy Dunlap observed a build problem with the following config:
CONFIG_SM_FTL=y
CONFIG_SM_FTL_MUSEUM=y
CONFIG_MTD_NAND=m
The ECC calculation routines are then built as a module, but referenced
by the sm_ftl code in the kernel, resulting in a build failure. The
simple fix is to make CONFIG_SM_FTL depend on MTD_NAND unconditionally
-- it's pointless without hardware support anyway.
Fix some typos which Randy pointed out, too.
Reported-By: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Randy Dunlap [Mon, 1 Mar 2010 21:54:19 +0000 (13:54 -0800)]
mtd/nand/r852: fix build for CONFIG_PM=n
Fix r852 build for the case of CONFIG_PM=n.
drivers/mtd/nand/r852.c:1039: error: implicit declaration of function 'pci_prepare_to_sleep'
drivers/mtd/nand/r852.c:1048: error: implicit declaration of function 'pci_back_from_sleep'
This patch leaves r852_pm_ops untouched.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Maxim Levitsky [Sat, 27 Feb 2010 00:04:02 +0000 (02:04 +0200)]
mtd: r852: Few fixes for problems that occur when card is rapidly inserted/removed.
First don't enable card detection logic to early. Second be very careful with
DMA engine, to be sure it doesn't write to kernel memory driver doesn't own.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Maxim Levitsky [Fri, 26 Feb 2010 20:08:40 +0000 (22:08 +0200)]
mtd: Few follow up cleanups for Smartmedia/xD support
* Test results of few functions that were declared with __must_check
* Fix bogus gcc warning about uinitialized variable 'ret'
* Remove unused variable from mtdblock_remove_dev
* Don't use deprecated DMA_32BIT_MASK
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Maxim Levitsky [Mon, 22 Feb 2010 18:39:42 +0000 (20:39 +0200)]
mtd: nand: Add driver for Ricoh xD/SmartMedia reader
This adds a driver for Ricoh R5C852 xD card reader.
This reader is a part of larger mulifunction chip
and found at least in R5C832
Driver is complete, but bewere of the fact that some
(probably only type M) xD cards are 'fake' which means that
they have an on board CPU and expose emulated nand command set
These cards don't even store the oob area on the flash,
but generate it on the fly from something else.
Thus they demand to have proper values written in the oob area,
and therefore only useful with SmartMedia FTL.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Maxim Levitsky [Mon, 22 Feb 2010 18:39:37 +0000 (20:39 +0200)]
mtd: nand: make reads using MTD_OOB_RAW affect only ECC validation
This changes the behavier of MTD_OOB_RAW. It used to read both OOB and
data to the data buffer, however you would still need to specify the
dummy oob buffer.
This is only used in one place, but makes it hard to read data+oob
without ECC test, thus I removed that behavier, and fixed the user.
Now MTD_OOB_RAW behaves just like MTD_OOB_PLACE, but doesn't do ECC
validation
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Maxim Levitsky [Mon, 22 Feb 2010 18:39:35 +0000 (20:39 +0200)]
mtd: nand: make MTD_OOB_PLACE work correctly.
MTD_OOB_PLACE is supposed to read/write the raw oob data similiar to the
MTD_OOB_RAW however due to a bug, currently it is not possible to read
more data that is specified by the oob 'free' regions.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Maxim Levitsky [Mon, 22 Feb 2010 18:39:34 +0000 (20:39 +0200)]
mtd: nand: make suspend work if device is accessed by kernel threads.
Since all userspace threads are frozen at the time the nand_suspend is called,
they aren't inside any nand function.
We don't call try_to_freeze in nand ether. Thus the only user that can
be inside the nand functions is an non freezeable kernel thread. Thus we
can safely wait for it to finish.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Maxim Levitsky [Mon, 22 Feb 2010 18:39:29 +0000 (20:39 +0200)]
mtd: blktrans: remove mtd_blkcore_priv, switch to per device queue and thread
This is the biggest change. To make hotplug possible, and this layer
clean, the mtd_blktrans_dev now contains everything for a single mtd
block translation device. Also removed some very old leftovers.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Adds NAND Flash Controller driver for MPC5121 Revision 2.
All device features, except hardware ECC and power management,
are supported.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com> Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Roel Kluin [Fri, 22 Jan 2010 21:22:52 +0000 (22:22 +0100)]
mtd: nand_bcm: fix hot spin and code duplication
In the branch where pagesize equalled NAND_DATA_ACCESS_SIZE, NumToRead
wasn't decremented in the `while (numToRead > 11)' loop.
Also the first and last while loops were duplicated in both branches.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Leo Chen <leochen@broadcom.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Vimal Singh [Thu, 7 Jan 2010 06:46:26 +0000 (12:16 +0530)]
mtd: omap2 fix prefetch mode read issue
There is a bug in nand prefetch read routine, which comes into effect
only if nand device is a 16-bit device (as we have in zoom boards).
This bug is effective only with below combination of conditions:
1. nand deivce, in use, is a 16 bit device
2. nand driver supports 'subpage' read
3. SW ECC is in use
This was not seen old kernel (ex: .23), because when, in early days,
we tested this (nand prefetch read in LDP boards) there was no
'subpage read' support.
Later when we had subpage read in (.27) kernel, we had hw ecc enabled
always in our internal tree. So, we missed this bug.
This patch fixes the issue.
Signed-off-by: Vimal Singh <vimalsingh@ti.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Vimal Singh [Tue, 5 Jan 2010 10:31:08 +0000 (16:01 +0530)]
mtd: omap2: correct 'info' pointer in 'omap_nand_remove'
Removing OMAP NAND driver, when loaded as a module, gives error and
does not get success. This fixes this and makes driver loadable and
removable run time.
Signed-off-by: Vimal Singh <vimalsingh@ti.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Vimal Singh [Tue, 5 Jan 2010 07:19:24 +0000 (12:49 +0530)]
mtd: omap2: fixing compilation warning
Fixing below warning in compilation:
drivers/mtd/nand/omap2.c: In function 'omap_write_buf_dma_pref':
drivers/mtd/nand/omap2.c:508: warning: passing argument 2 of
'omap_nand_dma_transfer' discards qualifiers from pointer target type
Signed-off-by: Vimal Singh <vimalsingh@ti.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Guillaume LECERF [Tue, 15 Dec 2009 22:01:06 +0000 (23:01 +0100)]
mtd: move more manufacturers to the common cfi.h header file
Move MANUFACTURER_MACRONIX and MANUFACTURER_SST definitions to the
include/linux/mtd/cfi.h header file and rename them to CFI_MFR_MACRONIX and
CFI_MFR_SST.
All references in drivers/mtd/chips/cfi_cmdset_0002.c are updated to reflect
this.
Signed-off-by: Guillaume LECERF <glecerf@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Roel Kluin [Mon, 15 Feb 2010 21:57:24 +0000 (22:57 +0100)]
mtd: inftl: misplaced parenthesis in find_boot_record
The parenthesis was misplaced, upon error a one was shown.
[dwmw2: Fix the code not to do the assignment within the if() statement] Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Vimal Singh [Wed, 3 Feb 2010 08:42:24 +0000 (14:12 +0530)]
mtd: nand: create a helper verification function
... verification for 'nand_erase_nand'
These checks are expected to be used by 'nand_lock' and 'nand_unlock'
routines too. As all these three are block aligned operations.
So, creating a helper function for this makes sense.
Ben Hutchings [Fri, 29 Jan 2010 20:59:53 +0000 (20:59 +0000)]
mtd: Raise limit on block device minor numbers
add_mtd_blktrans_dev() imposes a maximum of 257 devices per block
translator. This was presumably meant to prevent overflow back in the
days of 8-bit minor numbers. Instead, check against MINORMASK and the
limits of the partition naming scheme.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Ben Hutchings [Fri, 29 Jan 2010 20:58:37 +0000 (20:58 +0000)]
mtd: mtdblock: Dynamically allocate cache info structures
Since we allocate struct mtd_blktrans_dev for each block device, we
can add our own structure members to the end. Therefore embed
struct mtd_blktrans_dev in struct mtdblk_dev and remove the static
array of struct mtdblk_dev. Also remove the redundant pointer to
struct mtd_info.
This is preparation for removing the static limit on the number of MTD
devices.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mike Frysinger [Sun, 17 Jan 2010 15:52:46 +0000 (10:52 -0500)]
mtd: maps: Blackfin async: rename local funcs to avoid common clashes
There are new Blackfin MMR helper functions that use the same name as some
of the local functions in this driver, so have the driver use more specific
names to avoid the issue.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In mtd_ioctl MEMGETREGIONINFO the region_user_info pointer ur
is cast in __kernel space. This produces a number of sparse warnings
like:
warning: cast removes address space of expression
warning: incorrect type in initializer (different address spaces)
expected unsigned int const [noderef] <asn:1>*register __p
got unsigned int *<noident>
Since argp is already a void __user * just use it dirrectly without
the cast and make ur a __user *.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mtd: mxc-nand: don't disable clock in mxcnd-suspend
The clock must already be off after mtd->suspend. Disabling it again
results in an negative overflow of the clock usage count. This didn't
hurt as mxcnd_resume undid it after wake up.
mtd: mxc-nand: no need to check for validity of platform driver data
The probe function calls platform_set_drvdata with a valid pointer when
the probe is successful. As mxcnd_suspend and mxcnd_resume are only
called on bound devices, platform_get_drvdata always returns non-NULL.
This fix isn't critical as the pointer is always valid so it doesn't
matter if the compiler generated code for it or not.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Carlos O'Donell [Mon, 22 Feb 2010 23:25:59 +0000 (23:25 +0000)]
parisc: Set PCI CLS early in boot.
Set the PCI CLS early in the boot process to prevent
device failures. In pcibios_set_master use the new
pci_cache_line_size instead of a hard-coded value.
Signed-off-by: Carlos O'Donell <carlos@codesourcery.com> Reviewed-by: Grant Grundler <grundler@google.com> Signed-off-by: Kyle McMartin <kyle@redhat.com>
Michal Simek [Mon, 15 Feb 2010 09:50:42 +0000 (10:50 +0100)]
microblaze: Fix cache loop function for cache range
I create wrong asm code but none test shows that this part of code is wrong.
I am not convinces that were good idea to create asm optimized macros
for caches. The reason is that there is not optimization with previous code
that's why make sense to add old code and do some benchmarking which
functions are faster.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: bug fix for vlan + gro issue
tc35815: Remove a wrong netif_wake_queue() call which triggers BUG_ON
cdc_ether: new PID for Ericsson C3607w to the whitelist (resubmit)
IPv6: better document max_addresses parameter
MAINTAINERS: update mv643xx_eth maintenance status
e1000: Fix DMA mapping error handling on RX
iwlwifi: sanity check before counting number of tfds can be free
iwlwifi: error checking for number of tfds in queue
iwlwifi: set HT flags after channel in rxon
Ajit Khaparde [Tue, 16 Feb 2010 20:25:43 +0000 (20:25 +0000)]
net: bug fix for vlan + gro issue
Traffic (tcp) doesnot start on a vlan interface when gro is enabled.
Even the tcp handshake was not taking place.
This is because, the eth_type_trans call before the netif_receive_skb
in napi_gro_finish() resets the skb->dev to napi->dev from the previously
set vlan netdev interface. This causes the ip_route_input to drop the
incoming packet considering it as a packet coming from a martian source.
I could repro this on 2.6.32.7 (stable) and 2.6.33-rc7.
With this fix, the traffic starts and the test runs fine on both vlan
and non-vlan interfaces.
CC: Herbert Xu <herbert@gondor.apana.org.au> CC: Patrick McHardy <kaber@trash.net> Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 24 Feb 2010 02:15:05 +0000 (18:15 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: Be in TS_POLLING state during mwait based C-state entry
ACPI: Fix regression where _PPC is not read at boot even when ignore_ppc=0
acer-wmi: Respect current backlight level when loading
Linus Torvalds [Wed, 24 Feb 2010 02:13:34 +0000 (18:13 -0800)]
Merge branch 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/vmwgfx: Fix queries if no dma buffer thrashing is occuring.
drm/nv50: fix vram ptes on IGPs to point at stolen system memory
drm/nv50: fix instmem binding on IGPs to point at stolen system memory
drm/nv50: improve vram page table construction
drm/nv50: more efficient clearing of gpu page table entries
drm/nv50: make nv50_mem_vm_{bind,unbind} operate only on vram
drm/nouveau: Fix up pre-nv17 analog load detection.
Fixing the build the b94b08081fcecf83fa690d6c5664f6316fe72208 way
breaks xpc because genksyms then fails to generate an CRC for
per_cpu____sn_cnodeid_to_nasid because of limitations in the
generic genksyms code.
Signed-off-by: Hedi Berriche <hedi@sgi.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Atsushi Nemoto [Fri, 19 Feb 2010 05:13:58 +0000 (05:13 +0000)]
tc35815: Remove a wrong netif_wake_queue() call which triggers BUG_ON
The netif_wake_queue() is called correctly (i.e. only on !txfull
condition) from txdone routine. So Unconditional call to the
netif_wake_queue() here is wrong. This might cause calling of
start_xmit routine on txfull state and trigger BUG_ON.
This bug does not happen when NAPI disabled. After txdone there
must be at least one free tx slot. But with NAPI, this is not
true anymore and the BUG_ON can hits on heavy load.
In this driver NAPI was enabled on 2.6.33-rc1 so this is
regression from 2.6.32 kernel.
Reported-by: Ralf Roesch <ralf.roesch@rw-gmbh.de> Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
Torgny Johansson [Fri, 19 Feb 2010 01:59:15 +0000 (01:59 +0000)]
cdc_ether: new PID for Ericsson C3607w to the whitelist (resubmit)
This patch adds a new vid/pid to the cdc_ether whitelist.
Device added:
- Ericsson Mobile Broadband variant C3607w
Signed-off-by: Torgny Johansson <torgny.johansson@gmail.com>
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html Signed-off-by: David S. Miller <davem@davemloft.net>
Brian Haley [Mon, 22 Feb 2010 12:27:21 +0000 (12:27 +0000)]
IPv6: better document max_addresses parameter
Andrew Morton wrote:
>> >From ip-sysctl.txt file in kernel documentation I can see following description
>> for max_addresses:
>> max_addresses - INTEGER
>> Number of maximum addresses per interface. 0 disables limitation.
>> It is recommended not set too large value (or 0) because it would
>> be too easy way to crash kernel to allow to create too much of
>> autoconfigured addresses.
^^^^^^^^^^^^^^
>> If this parameter applies only for auto-configured IP addressed, please state
>> it more clearly in docs or rename the parameter to show that it refers to
>> auto-configuration.
It did mention autoconfigured in the text, but the below makes it more obvious.
More clearly document IPv6 max_addresses parameter.
Signed-off-by: Brian Haley <brian.haley@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Blanchard [Fri, 19 Feb 2010 17:54:53 +0000 (17:54 +0000)]
e1000: Fix DMA mapping error handling on RX
Check for error return from pci_map_single/pci_map_page and clean up.
With this and the previous patch the driver was able to handle a significant
percentage of errors (I set the fault injection rate to 10% and could still
download large files at a reasonable speed).
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
"Benjamin S." <sbenni@gmx.de> reports that the patch in question
causes a big drop in sequential throughput for him, dropping from
200MB/sec down to only 70MB/sec.
Needs to be investigated more fully, for now lets just revert the
offending commit.
Dave Airlie [Tue, 23 Feb 2010 05:42:18 +0000 (15:42 +1000)]
Merge remote branch 'nouveau/for-airlied' of ../drm-nouveau-next into drm-linus
* 'nouveau/for-airlied' of ../drm-nouveau-next:
drm/nv50: fix vram ptes on IGPs to point at stolen system memory
drm/nv50: fix instmem binding on IGPs to point at stolen system memory
drm/nv50: improve vram page table construction
drm/nv50: more efficient clearing of gpu page table entries
drm/nv50: make nv50_mem_vm_{bind,unbind} operate only on vram
drm/nouveau: Fix up pre-nv17 analog load detection.
Michael Neuling [Mon, 22 Feb 2010 20:44:24 +0000 (12:44 -0800)]
fs/exec.c: fix initial stack reservation
803bf5ec259941936262d10ecc84511b76a20921 ("fs/exec.c: restrict initial
stack space expansion to rlimit") attempts to limit the initial stack to
20*PAGE_SIZE. Unfortunately, in attempting ensure the stack is not
reduced in size, we ended up not changing the stack at all.
This size reduction check is not necessary as the expand_stack call does
this already.
This caused a regression in UML resulting in most guest processes being
killed.
Signed-off-by: Michael Neuling <mikey@neuling.org> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Acked-by: WANG Cong <xiyou.wangcong@gmail.com> Cc: Anton Blanchard <anton@samba.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: James Morris <jmorris@namei.org> Cc: Serge Hallyn <serue@us.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Jouni Malinen <j@w1.fi> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marcin Slusarz [Mon, 22 Feb 2010 20:44:22 +0000 (12:44 -0800)]
efifb: fix framebuffer handoff
Commit 4410f3910947dcea8672280b3adecd53cec4e85e ("fbdev: add support for
handoff from firmware to hw framebuffers") didn't add fb_destroy
operation to efifb. Fix it and change aperture_size to match size
passed to request_mem_region.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Reported-by: Alex Zhavnerchik <alex.vizor@gmail.com> Tested-by: Alex Zhavnerchik <alex.vizor@gmail.com> Acked-by: Peter Jones <pjones@redhat.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Dave Airlie <airlied@redhat.com> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jens Rottmann [Mon, 22 Feb 2010 20:44:20 +0000 (12:44 -0800)]
geode-mfgpt: restore previous behavior for selecting IRQ
geode-mfgpt: restore previous behavior for selecting IRQ
The MFGPT IRQ used to be, in order of decreasing priority,
* IRQ supplied by the user as a boot-time parameter,
* IRQ previously set by the BIOS or another driver,
* default IRQ given at compile time.
Return to this behavior, which got broken when splitting the
MFGPT/clocksource driver for 2.6.33-rc1.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de> Acked-by: Andres Salomon <dilinger@collabora.co.uk> Cc: Jordan Crouse <jordan.crouse@amd.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: john stultz <johnstul@us.ibm.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pa[idp->layers] should be cleared even if it's not used by
sub_alloc() because it's used by mark idr_mark_full().
* The original condition check also assigned pa[l] to p which the new
code didn't do thus leaving p pointing at the wrong layer.
Both problems have been fixed and the idr code has received good amount
testing using userland testing setup where simple bitmap allocator is
run parallel to verify the result of idr allocation.
The bug this patch fixes is caused by sub_alloc() optimization path
bypassing out-of-room condition check and restarting allocation loop
with starting value higher than maximum allowed value. For detailed
description, please read commit message of 859ddf09.
Signed-off-by: Tejun Heo <tj@kernel.org>
Based-on-patch-from: Eric Paris <eparis@redhat.com> Reported-by: Eric Paris <eparis@redhat.com> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Tested-by: Serge Hallyn <serue@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Skeggs [Fri, 19 Feb 2010 22:06:36 +0000 (08:06 +1000)]
drm/nv50: fix instmem binding on IGPs to point at stolen system memory
This also modifies the unused PRAMIN PT entries to be all zeroes, can't
really recall why I used 9/0 initially, just that it didn't work for
some reason. It was likely masking a bug elsewhere that's since been
fixed.
Ben Skeggs [Thu, 11 Feb 2010 01:31:44 +0000 (11:31 +1000)]
drm/nv50: improve vram page table construction
This commit changes nouveau to construct PTEs which look very much like
the ones the binary driver creates.
I presume that filling multiple PTEs identically with length flags and
the physical address of the start of a block of VRAM is a hint to the
memory controller that it need not perform additional page table lookups
for that range of addresses.
projects / linux-beck.git / log