I had occasional screen corruption with the matrox framebuffer driver and
I found out that the reason for the corruption is that the hardware
blitter accesses the videoram while it is being written to.
The matrox driver has a macro WaitTillIdle() that should wait until the
blitter is idle, but it sometimes doesn't work. I added a dummy read
mga_inl(M_STATUS) to WaitTillIdle() to fix the problem. The dummy read
will flush the write buffer in the PCI chipset, and the next read of
M_STATUS will return the hardware status.
Since applying this patch, I had no screen corruption at all.
The variable "size" is expressed as number of blocks and not as
number of clusters, this could trigger a kernel panic when using
ext4 with the size of a cluster different from the size of a block.
Tail of a page straddling inode size must be zeroed when being written
out due to POSIX requirement that modifications of mmaped page beyond
inode size must not be written to the file. ext4_bio_write_page() did
this only for blocks fully beyond inode size but didn't properly zero
blocks partially beyond inode size. Fix this.
The problem has been uncovered by mmap_11-4 test in openposix test suite
(part of LTP).
Reported-by: Xiaoguang Wang <wangxg.fnst@cn.fujitsu.com> Fixes: 5a0dc7365c240 Fixes: bd2d0210cf22f CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we perform a data integrity sync we tag all the dirty pages with
PAGECACHE_TAG_TOWRITE at start of ext4_da_writepages. Later we check
for this tag in write_cache_pages_da and creates a struct
mpage_da_data containing contiguously indexed pages tagged with this
tag and sync these pages with a call to mpage_da_map_and_submit. This
process is done in while loop until all the PAGECACHE_TAG_TOWRITE
pages are synced. We also do journal start and stop in each iteration.
journal_stop could initiate journal commit which would call
ext4_writepage which in turn will call ext4_bio_write_page even for
delayed OR unwritten buffers. When ext4_bio_write_page is called for
such buffers, even though it does not sync them but it clears the
PAGECACHE_TAG_TOWRITE of the corresponding page and hence these pages
are also not synced by the currently running data integrity sync. We
will end up with dirty pages although sync is completed.
This could cause a potential data loss when the sync call is followed
by a truncate_pagecache call, which is exactly the case in
collapse_range. (It will cause generic/127 failure in xfstests)
To avoid this issue, we can use set_page_writeback_keepwrite instead of
set_page_writeback, which doesn't clear TOWRITE tag.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com> Signed-off-by: Ashish Sangwan <a.sangwan@samsung.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IRB might be 96 bytes if the extended-I/O-measurement facility is
used. This feature is currently not used by Linux, but struct irb
already has the emw defined. So let's make the irb in lowcore match the
size of the internal data structure to be future proof.
We also have to add a pad, to correctly align the paste.
The bigger irb field also circumvents a bug in some QEMU versions that
always write the emw field on test subchannel and therefore destroy the
paste definitions of this CPU. Running under these QEMU version broke
some timing functions in the VDSO and all users of these functions,
e.g. some JREs.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Sebastian Ott <sebott@linux.vnet.ibm.com> Cc: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Analog to git commit 28b92e09e25bdc0ae864b22eacf195a74f861389
first cast tk->wall_to_monotonic.tv_nsec to u64 before doing
the shift with tk->shift to avoid loosing relevant bits on a
32-bit kernel.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
idr_replace() open-codes the logic to calculate the maximum valid ID
given the height of the idr tree; unfortunately, the open-coded logic
doesn't account for the fact that the top layer may have unused slots
and over-shifts the limit to zero when the tree is at its maximum
height.
The following test code shows it fails to replace the value for
id=((1<<27)+42):
static void test5(void)
{
int id;
DEFINE_IDR(test_idr);
#define TEST5_START ((1<<27)+42) /* use the highest layer */
Fix the bug by using idr_max() which correctly takes into account the
maximum allowed shift.
sub_alloc() shares the same problem and may incorrectly fail with
-EAGAIN; however, this bug doesn't affect correct operation because
idr_get_empty_slot(), which already uses idr_max(), retries with the
increased @id in such cases.
Currently core file of aarch32 process prstatus note has empty
registers set. As result aarch32 core files create by V8 kernel are
not very useful.
It happens because compat_gpr_get and compat_gpr_set functions can
copy registers values to/from either kbuf or ubuf. ELF core file
collection function fill_thread_core_info calls compat_gpr_get
with kbuf set and ubuf set to 0. But current compat_gpr_get and
compat_gpr_set function handle copy to/from only ubuf case.
Fix is to handle kbuf and ubuf as two separate cases in similar
way as other functions like user_regset_copyout, user_regset_copyin do.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our compat PTRACE_POKEUSR implementation simply passes the user data to
regset_copy_from_user after some simple range checking. Unfortunately,
the data in question has already been copied to the kernel stack by this
point, so the subsequent access_ok check fails and the ptrace request
returns -EFAULT. This causes problems tracing fork() with older versions
of strace.
This patch briefly changes the fs to KERNEL_DS, so that the access_ok
check passes even with a kernel address.
When tracing a process in another pid namespace, it's important for fork
event messages to contain the child's pid as seen from the tracer's pid
namespace, not the parent's. Otherwise, the tracer won't be able to
correlate the fork event with later SIGTRAP signals it receives from the
child.
We still risk a race condition if a ptracer from a different pid
namespace attaches after we compute the pid_t value. However, sending a
bogus fork event message in this unlikely scenario is still a vast
improvement over the status quo where we always send bogus fork event
messages to debuggers in a different pid namespace than the forking
process.
Signed-off-by: Matthew Dempsky <mdempsky@chromium.org> Acked-by: Oleg Nesterov <oleg@redhat.com> Cc: Kees Cook <keescook@chromium.org> Cc: Julien Tinnes <jln@chromium.org> Cc: Roland McGrath <mcgrathr@chromium.org> Cc: Jan Kratochvil <jan.kratochvil@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When kswapd exits, it can end up taking locks that were previously held
by allocating tasks while they waited for reclaim. Lockdep currently
warns about this:
On Wed, May 28, 2014 at 06:06:34PM +0800, Gu Zheng wrote:
> inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-R} usage.
> kswapd2/1151 [HC0[0]:SC0[0]:HE1:SE1] takes:
> (&sig->group_rwsem){+++++?}, at: exit_signals+0x24/0x130
> {RECLAIM_FS-ON-W} state was registered at:
> mark_held_locks+0xb9/0x140
> lockdep_trace_alloc+0x7a/0xe0
> kmem_cache_alloc_trace+0x37/0x240
> flex_array_alloc+0x99/0x1a0
> cgroup_attach_task+0x63/0x430
> attach_task_by_pid+0x210/0x280
> cgroup_procs_write+0x16/0x20
> cgroup_file_write+0x120/0x2c0
> vfs_write+0xc0/0x1f0
> SyS_write+0x4c/0xa0
> tracesys+0xdd/0xe2
> irq event stamp: 49
> hardirqs last enabled at (49): _raw_spin_unlock_irqrestore+0x36/0x70
> hardirqs last disabled at (48): _raw_spin_lock_irqsave+0x2b/0xa0
> softirqs last enabled at (0): copy_process.part.24+0x627/0x15f0
> softirqs last disabled at (0): (null)
>
> other info that might help us debug this:
> Possible unsafe locking scenario:
>
> CPU0
> ----
> lock(&sig->group_rwsem);
> <Interrupt>
> lock(&sig->group_rwsem);
>
> *** DEADLOCK ***
>
> no locks held by kswapd2/1151.
>
> stack backtrace:
> CPU: 30 PID: 1151 Comm: kswapd2 Not tainted 3.10.39+ #4
> Call Trace:
> dump_stack+0x19/0x1b
> print_usage_bug+0x1f7/0x208
> mark_lock+0x21d/0x2a0
> __lock_acquire+0x52a/0xb60
> lock_acquire+0xa2/0x140
> down_read+0x51/0xa0
> exit_signals+0x24/0x130
> do_exit+0xb5/0xa50
> kthread+0xdb/0x100
> ret_from_fork+0x7c/0xb0
This is because the kswapd thread is still marked as a reclaimer at the
time of exit. But because it is exiting, nobody is actually waiting on
it to make reclaim progress anymore, and it's nothing but a regular
thread at this point. Be tidy and strip it of all its powers
(PF_MEMALLOC, PF_SWAPWRITE, PF_KSWAPD, and the lockdep reclaim state)
before returning from the thread function.
Some drivers use the first HID report in the list instead of using an
index. In these cases, validation uses ID 0, which was supposed to mean
"first known report". This fixes the problem, which was causing at least
the lgff family of devices to stop working since hid_validate_values
was being called with ID 0, but the devices used single numbered IDs
for their reports:
Right, since conversion to mutex then rwsem, we should not put_anon_vma()
from inside an rcu_read_lock()ed section: fix the two places that did so.
And add might_sleep() to anon_vma_free(), as suggested by Peter Zijlstra.
Fixes: 88c22088bf23 ("mm: optimize page_lock_anon_vma() fast-path") Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently memory error handler handles action optional errors in the
deferred manner by default. And if a recovery aware application wants
to handle it immediately, it can do it by setting PF_MCE_EARLY flag.
However, such signal can be sent only to the main thread, so it's
problematic if the application wants to have a dedicated thread to
handler such signals.
So this patch adds dedicated thread support to memory error handler. We
have PF_MCE_EARLY flags for each thread separately, so with this patch
AO signal is sent to the thread with PF_MCE_EARLY flag set, not the main
thread. If you want to implement a dedicated thread, you call prctl()
to set PF_MCE_EARLY on the thread.
Memory error handler collects processes to be killed, so this patch lets
it check PF_MCE_EARLY flag on each thread in the collecting routines.
No behavioral change for all non-early kill cases.
Tony said:
: The old behavior was crazy - someone with a multithreaded process might
: well expect that if they call prctl(PF_MCE_EARLY) in just one thread, then
: that thread would see the SIGBUS with si_code = BUS_MCEERR_A0 - even if
: that thread wasn't the main thread for the process.
When Linux sees an "action optional" machine check (where h/w has reported
an error that is not in the current execution path) we generally do not
want to signal a process, since most processes do not have a SIGBUS
handler - we'd just prematurely terminate the process for a problem that
they might never actually see.
task_early_kill() decides whether to consider a process - and it checks
whether this specific process has been marked for early signals with
"prctl", or if the system administrator has requested early signals for
all processes using /proc/sys/vm/memory_failure_early_kill.
But for MF_ACTION_REQUIRED case we must not defer. The error is in the
execution path of the current thread so we must send the SIGBUS
immediatley.
Fix by passing a flag argument through collect_procs*() to
task_early_kill() so it knows whether we can defer or must take action.
When a thread in a multi-threaded application hits a machine check because
of an uncorrectable error in memory - we want to send the SIGBUS with
si.si_code = BUS_MCEERR_AR to that thread. Currently we fail to do that
if the active thread is not the primary thread in the process.
collect_procs() just finds primary threads and this test:
if ((flags & MF_ACTION_REQUIRED) && t == current) {
will see that the thread we found isn't the current thread and so send a
si.si_code = BUS_MCEERR_AO to the primary (and nothing to the active
thread at this time).
We can fix this by checking whether "current" shares the same mm with the
process that collect_procs() said owned the page. If so, we send the
SIGBUS to current (with code BUS_MCEERR_AR).
Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Reported-by: Otto Bruggeman <otto.g.bruggeman@intel.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Borislav Petkov <bp@suse.de> Cc: Chen Gong <gong.chen@linux.jf.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The test_bit operations in get/set pageblock flags are expensive. This
patch reads the bitmap on a word basis and use shifts and masks to isolate
the bits of interest. Similarly masks are used to set a local copy of the
bitmap and then use cmpxchg to update the bitmap if there have been no
other changes made in parallel.
In a test running dd onto tmpfs the overhead of the pageblock-related
functions went from 1.27% in profiles to 0.5%.
In addition to the performance benefits, this patch closes races that are
possible between:
a) get_ and set_pageblock_migratetype(), where get_pageblock_migratetype()
reads part of the bits before and other part of the bits after
set_pageblock_migratetype() has updated them.
b) set_pageblock_migratetype() and set_pageblock_skip(), where the non-atomic
read-modify-update set bit operation in set_pageblock_skip() will cause
lost updates to some bits changed in the set_pageblock_migratetype().
Joonsoo Kim first reported the case a) via code inspection. Vlastimil
Babka's testing with a debug patch showed that either a) or b) occurs
roughly once per mmtests' stress-highalloc benchmark (although not
necessarily in the same pageblock). Furthermore during development of
unrelated compaction patches, it was observed that frequent calls to
{start,undo}_isolate_page_range() the race occurs several thousands of
times and has resulted in NULL pointer dereferences in move_freepages()
and free_one_page() in places where free_list[migratetype] is
manipulated by e.g. list_move(). Further debugging confirmed that
migratetype had invalid value of 6, causing out of bounds access to the
free_list array.
That confirmed that the race exist, although it may be extremely rare,
and currently only fatal where page isolation is performed due to
memory hot remove. Races on pageblocks being updated by
set_pageblock_migratetype(), where both old and new migratetype are
lower MIGRATE_RESERVE, currently cannot result in an invalid value
being observed, although theoretically they may still lead to
unexpected creation or destruction of MIGRATE_RESERVE pageblocks.
Furthermore, things could get suddenly worse when memory isolation is
used more, or when new migratetypes are added.
After this patch, the race has no longer been observed in testing.
Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Vlastimil Babka <vbabka@suse.cz> Reported-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Reported-and-tested-by: Vlastimil Babka <vbabka@suse.cz> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Jan Kara <jack@suse.cz> Cc: Michal Hocko <mhocko@suse.cz> Cc: Hugh Dickins <hughd@google.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Theodore Ts'o <tytso@mit.edu> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
throttle_direct_reclaim() is meant to trigger during swap-over-network
during which the min watermark is treated as a pfmemalloc reserve. It
throttes on the first node in the zonelist but this is flawed.
The user-visible impact is that a process running on CPU whose local
memory node has no ZONE_NORMAL will stall for prolonged periods of time,
possibly indefintely. This is due to throttle_direct_reclaim thinking the
pfmemalloc reserves are depleted when in fact they don't exist on that
node.
On a NUMA machine running a 32-bit kernel (I know) allocation requests
from CPUs on node 1 would detect no pfmemalloc reserves and the process
gets throttled. This patch adjusts throttling of direct reclaim to
throttle based on the first node in the zonelist that has a usable
ZONE_NORMAL or lower zone.
Commit 786235eeba0e ("kthread: make kthread_create() killable") meant
for allowing kthread_create() to abort as soon as killed by the
OOM-killer. But returning -ENOMEM is wrong if killed by SIGKILL from
userspace. Change kthread_create() to return -EINTR upon SIGKILL.
Currently hugepage migration is available for all archs which support
pmd-level hugepage, but testing is done only for x86_64 and there're
bugs for other archs. So to avoid breaking such archs, this patch
limits the availability strictly to x86_64 until developers of other
archs get interested in enabling this feature.
Simply disabling hugepage migration on non-x86_64 archs is not enough to
fix the reported problem where sys_move_pages() hits the BUG_ON() in
follow_page(FOLL_GET), so let's fix this by checking if hugepage
migration is supported in vma_migratable().
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Reported-by: Michael Ellerman <mpe@ellerman.id.au> Tested-by: Michael Ellerman <mpe@ellerman.id.au> Acked-by: Hugh Dickins <hughd@google.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Tony Luck <tony.luck@intel.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: David Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leandro Liptak reports that his HASEE E200 computer hangs when we ask
the BIOS to hand over control of the EHCI host controller. This
definitely sounds like a bug in the BIOS, but at the moment there is
no way to fix it.
This patch works around the problem by avoiding the handoff whenever
the motherboard and BIOS version match those of Leandro's computer.
Commit 193ab2a60700 ("usb: gadget: allow multiple gadgets to be built")
apparently required that checks for CONFIG_USB_GADGET_OMAP would be
replaced with checks for CONFIG_USB_OMAP. Do so now for the remaining
checks for CONFIG_USB_GADGET_OMAP, even though these checks have
basically been broken since v3.1.
And, since we're touching this code, use the IS_ENABLED() macro, so
things will now (hopefully) also work if USB_OMAP is modular.
Fixes: 193ab2a60700 ("usb: gadget: allow multiple gadgets to be built") Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
so it seems like DWC3 IP doesn't clear stalls
automatically when we disable an endpoint, because
of that, we _must_ make sure stalls are cleared
before clearing the proper bit in DALEPENA register.
Reported-by: Johannes Stezenbach <js@sig21.net> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 193ab2a60700 ("usb: gadget: allow multiple gadgets to be built")
basically renamed the Kconfig symbol USB_GADGET_PXA25X to USB_PXA25X. It
did not rename the related macros in use at that time. Commit c0a39151a405 ("ARM: pxa: fix inconsistent CONFIG_USB_PXA27X") did so for
all but one macro. Rename that last macro too now.
Fixes: 193ab2a60700 ("usb: gadget: allow multiple gadgets to be built") Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In usbtest, tests 5 - 8 use the scatter-gather library in usbcore
without any sort of timeout. If there's a problem in the gadget or
host controller being tested, the test can hang.
This patch adds a 10-second timeout to the tests, so that they will
fail gracefully with an ETIMEDOUT error instead of hanging.
TEST 12 and TEST 24 unlinks the URB write request for N times. When
host and gadget both initialize pattern 1 (mod 63) data series to
transfer, the gadget side will complain the wrong data which is not
expected. Because in host side, usbtest doesn't fill the data buffer
as mod 63 and this patch fixed it.
[20285.488974] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.489181] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.489423] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb50800 length 512 last
[20285.489727] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000a9eaf00000000000
[20285.490055] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.490281] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.490492] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Active
[20285.490713] dwc3 dwc3.0.auto: ep1out-bulk: endpoint busy
[20285.490909] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Complete
[20285.491117] dwc3 dwc3.0.auto: request ffff8800aa6cb480 from ep1out-bulk completed 512/512 ===> 0
[20285.491431] zero gadget: bad OUT byte, buf[1] = 0
[20285.491605] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Set Stall' params 000000000000000000000000
[20285.491915] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.492099] dwc3 dwc3.0.auto: queing request ffff8800aa6cb480 to ep1out-bulk length 512
[20285.492387] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.492595] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.492830] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb51000 length 512 last
[20285.493135] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000a9eaf00000000000
[20285.493465] dwc3 dwc3.0.auto: Command Complete --> 0
The ->SupportedRates[] array has NDIS_802_11_LENGTH_RATES_EX (16)
elements. Since "ie_len" comes from then network and can go up to 255
then it means we should add a range check to prevent memory corruption.
Fixes: d6846af679e0 ('staging: r8188eu: Add files for new driver - part 7') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d0f47ff17f29 ("ASoC: OMAP: Build config cleanup for McBSP")
removed the Kconfig symbol OMAP_MCBSP. It left two checks for
CONFIG_OMAP_MCBSP untouched.
Convert these to checks for CONFIG_SND_OMAP_SOC_MCBSP. That must be
correct, since that re-enables calls to functions that are all found in
sound/soc/omap/mcbsp.c. And that file is built only if
CONFIG_SND_OMAP_SOC_MCBSP is defined.
Fixes: d0f47ff17f29 ("ASoC: OMAP: Build config cleanup for McBSP") Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In probe the driver queued delayed work for cable detection and
returned the result of queue_delayed_work() call. However the return
value of queue_delayed_work() does not indicate an error and in normal
condition it returns true which means successful work queue.
This effectively resulted in probe failure:
[ 2.088204] max14577-muic: probe of max77836-muic failed with error 1
Fix null-pointer dereference at probe when the mdio platform device is
missing (e.g. when it has been disabled in DT).
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When sending data through IUCV a MESSAGE COMPLETE interrupt
signals that sent data memory can be freed or reused again.
With commit f9c41a62bba3f3f7ef3541b2a025e3371bcbba97
"af_iucv: fix recvmsg by replacing skb_pull() function" the
MESSAGE COMPLETE callback iucv_callback_txdone() identifies
the wrong skb as being confirmed, which leads to data corruption.
This patch fixes the skb mapping logic in iucv_callback_txdone().
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix potential null-pointer dereference at probe if the mdio-gpio device
has not been successfully probed yet.
The offending commit is plain wrong for a number of reasons. First of
all it accesses internal driver data of an unrelated device. Neither
does it check that the data is non-null (which it is in case the device
has not been probed yet).
Furthermore, the decision on whether to treat any driver data according
to the mdio-gpio driver's internals is made based on the node name. But
the name is not compared against "mdio" which is the normal name for the
node, but rather against "gpio" which the node does not have to be named
(and shouldn't be according to the binding documentation). [ If this
hack is to be kept out-of-tree it should at least be matching against
the compatible property. ]
Cc: Stefan Roese <sr@denx.de> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ALSA control code expects that the range of assigned indices to a control is
continuous and does not overflow. Currently there are no checks to enforce this.
If a control with a overflowing index range is created that control becomes
effectively inaccessible and unremovable since snd_ctl_find_id() will not be
able to find it. This patch adds a check that makes sure that controls with a
overflowing index range can not be created.
Each control gets automatically assigned its numids when the control is created.
The allocation is done by incrementing the numid by the amount of allocated
numids per allocation. This means that excessive creation and destruction of
controls (e.g. via SNDRV_CTL_IOCTL_ELEM_ADD/REMOVE) can cause the id to
eventually overflow. Currently when this happens for the control that caused the
overflow kctl->id.numid + kctl->count will also over flow causing it to be
smaller than kctl->id.numid. Most of the code assumes that this is something
that can not happen, so we need to make sure that it won't happen
A control that is visible on the card->controls list can be freed at any time.
This means we must not access any of its memory while not holding the
controls_rw_lock. Otherwise we risk a use after free access.
There are two issues with the current implementation for replacing user
controls. The first is that the code does not check if the control is actually a
user control and neither does it check if the control is owned by the process
that tries to remove it. That allows userspace applications to remove arbitrary
controls, which can cause a user after free if a for example a driver does not
expect a control to be removed from under its feed.
The second issue is that on one hand when a control is replaced the
user_ctl_count limit is not checked and on the other hand the user_ctl_count is
increased (even though the number of user controls does not change). This allows
userspace, once the user_ctl_count limit as been reached, to repeatedly replace
a control until user_ctl_count overflows. Once that happens new controls can be
added effectively bypassing the user_ctl_count limit.
Both issues can be fixed by instead of open-coding the removal of the control
that is to be replaced to use snd_ctl_remove_user_ctl(). This function does
proper permission checks as well as decrements user_ctl_count after the control
has been removed.
Note that by using snd_ctl_remove_user_ctl() the check which returns -EBUSY at
beginning of the function if the control already exists is removed. This is not
a problem though since the check is quite useless, because the lock that is
protecting the control list is released between the check and before adding the
new control to the list, which means that it is possible that a different
control with the same settings is added to the list after the check. Luckily
there is another check that is done while holding the lock in snd_ctl_add(), so
we'll rely on that to make sure that the same control is not added twice.
The user-control put and get handlers as well as the tlv do not protect against
concurrent access from multiple threads. Since the state of the control is not
updated atomically it is possible that either two write operations or a write
and a read operation race against each other. Both can lead to arbitrary memory
disclosure. This patch introduces a new lock that protects user-controls from
concurrent access. Since applications typically access controls sequentially
than in parallel a single lock per card should be fine.
According to the bug reporter (Данило Шеган), the external mic
starts to work and has proper jack detection if only pin 0x19
is marked properly as an external headset mic.
AlsaInfo at https://bugs.launchpad.net/ubuntu/+source/pulseaudio/+bug/1328587/+attachment/4128991/+files/AlsaInfo.txt
Cancel the optimization of compiler for struct snd_compr_avail
which size will be 0x1c in 32bit kernel while 0x20 in 64bit
kernel under the optimizer. That will make compaction between
32bit and 64bit. So add packed to fix the size of struct
snd_compr_avail to 0x1c for all platform.
Given some pathologically compressed data, lz4 could possibly decide to
wrap a few internal variables, causing unknown things to happen. Catch
this before the wrapping happens and abort the decompression.
Reported-by: "Don A. Bailey" <donb@securitymouse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lzo decompressor can, if given some really crazy data, possibly
overrun some variable types. Modify the checking logic to properly
detect overruns before they happen.
Reported-by: "Don A. Bailey" <donb@securitymouse.com> Tested-by: "Don A. Bailey" <donb@securitymouse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
at91_adc_get_trigger_value_by_name() was returning -ENOMEM truncated to
a positive u8 and that doesn't work. I've changed it to int and
refactored it to preserve the error code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some unknown reason the parameters for snd_soc_test_bits() were in wrong
order:
It was:
snd_soc_test_bits(codec, val, mask, reg); /* WRONG!!! */
while it should be:
snd_soc_test_bits(codec, reg, mask, val);
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reset needs to wait 20ms before other codec IO is performed. This wait
was not being performed. Fix this by making sure the reset register is not
restored with the cache, but use the manual reset method in resume with
the wait.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using auto-muted controls it may happen that the register value will not
change when changing a control from enabled to disabled (since the control might
be physically disabled due to the auto-muting). We have to make sure to still
update the DAPM graph and disconnect the mixer input.
We try to free two pages when only one has been allocated.
Cleanup path is unlikely, so I haven't found any trace that would fit,
but I hope that free_pages_prepare() does catch it.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Reviewed-by: Amos Kong <akong@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code posts periodic memory pressure status from a dedicated thread.
Under some conditions, especially when we are releasing a lot of memory into
the guest, we may not send timely pressure reports back to the host. Fix this
issue by reporting pressure in all contexts that can be active in this driver.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should stop I/O unconditionally at suspend rather than rely on the
tty-port initialised flag (which is set prior to stopping I/O during
shutdown) in order to prevent suspend returning with URBs still active.
Fixes: 11ea859d64b6 ("USB: additional power savings for cdc-acm devices
that support remote wakeup")
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current ACM runtime-suspend implementation is broken in several
ways:
Firstly, it buffers only the first write request being made while
suspended -- any further writes are silently dropped.
Secondly, writes being dropped also leak write urbs, which are never
reclaimed (until the device is unbound).
Thirdly, even the single buffered write is not cleared at shutdown
(which may happen before the device is resumed), something which can
lead to another urb leak as well as a PM usage-counter leak.
Fix this by implementing a delayed-write queue using urb anchors and
making sure to discard the queue properly at shutdown.
Fixes: 11ea859d64b6 ("USB: additional power savings for cdc-acm devices
that support remote wakeup")
Reported-by: Xiao Jin <jin.xiao@intel.com> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix race between write() and resume() due to improper locking that could
lead to writes being reordered.
Resume must be done atomically and susp_count be protected by the
write_lock in order to prevent racing with write(). This could otherwise
lead to writes being reordered if write() grabs the write_lock after
susp_count is decremented, but before the delayed urb is submitted.
Fixes: 11ea859d64b6 ("USB: additional power savings for cdc-acm devices
that support remote wakeup")
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix race between write() and suspend() which could lead to writes being
dropped (or I/O while suspended) if the device is runtime suspended
while a write request is being processed.
Specifically, suspend() releases the write_lock after determining the
device is idle but before incrementing the susp_count, thus leaving a
window where a concurrent write() can submit an urb.
Fixes: 11ea859d64b6 ("USB: additional power savings for cdc-acm devices
that support remote wakeup")
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each MIPS KVM guest has its own copy of the KVM exception vector. This
contains the TLB refill exception handler at offset 0x000, the general
exception handler at offset 0x180, and interrupt exception handlers at
offset 0x200 in case Cause_IV=1. A common handler is copied to offset
0x2000 and offset 0x3000 is used for temporarily storing k1 during entry
from guest.
However the amount of memory allocated for this purpose is calculated as
0x200 rounded up to the next page boundary, which is insufficient if 4KB
pages are in use. This can lead to the common handler at offset 0x2000
being overwritten and infinitely recursive exceptions on the next exit
from the guest.
Increase the minimum size from 0x200 to 0x4000 to cover the full use of
the page.
When Hyper-V enlightenments are in effect, Windows prefers to issue an
Hyper-V MSR write to issue an EOI rather than an x2apic MSR write.
The Hyper-V MSR write is not handled by the processor, and besides
being slower, this also causes bugs with APIC virtualization. The
reason is that on EOI the processor will modify the highest in-service
interrupt (SVI) field of the VMCS, as explained in section 29.1.4 of
the SDM; every other step in EOI virtualization is already done by
apic_send_eoi or on VM entry, but this one is missing.
We need to do the same, and be careful not to muck with the isr_count
and highest_isr_cache fields that are unused when virtual interrupt
delivery is enabled.
Reviewed-by: Yang Zhang <yang.z.zhang@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following commit befdf89 "net/mlx4_core: Preserve pci_dev_data after
__mlx4_remove_one()", there are two mlx4 pci callbacks which will
attempt to release the mlx4_priv object -- .shutdown and .remove.
This leads to a use-after-free access to the already freed mlx4_priv
instance and trigger a "Kernel access of bad area" crash when both
.shutdown and .remove are called.
During reboot or kexec, .shutdown is called, with the VFs probed to
the host going through shutdown first and then the PF. Later, the PF
will trigger VFs' .remove since VFs still have driver attached.
Fix that by keeping only one driver entry which releases mlx4_priv.
Fixes: befdf89 ('net/mlx4_core: Preserve pci_dev_data after __mlx4_remove_one()') CC: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_match_id() just match the static pci_device_id, which may return NULL if
someone binds the driver to a device manually using
/sys/bus/pci/drivers/.../new_id.
This patch wrap up a helper function __mlx4_remove_one() which does the tear
down function but preserve the drv_data. Functions like
mlx4_pci_err_detected() and mlx4_restart_one() will call this one with out
releasing drvdata.
Fixes: 97a5221 "net/mlx4_core: pass pci_device_id.driver_data to __mlx4_init_one during reset". CC: Bjorn Helgaas <bhelgaas@google.com> CC: Amir Vadai <amirv@mellanox.com> CC: Jack Morgenstein <jackm@dev.mellanox.co.il> CC: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com> Acked-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Its too easy to add thousand of UDP sockets on a particular bucket,
and slow down an innocent multicast receiver.
Early demux is supposed to be an optimization, we should avoid spending
too much time in it.
It is interesting to note __udp4_lib_demux_lookup() only tries to
match first socket in the chain.
10 is the threshold we already have in __udp4_lib_lookup() to switch
to secondary hash.
Fixes: 421b3885bf6d5 ("udp: ipv4: Add udp early demux") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: David Held <drheld@google.com> Cc: Shawn Bohrer <sbohrer@rgmadvisors.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we mirror packets from a vxlan tunnel to other device,
the mirror device should see the same packets (that is, without
outer header). Because vxlan tunnel sets dev->hard_header_len,
tcf_mirred() resets mac header back to outer mac, the mirror device
actually sees packets with outer headers
Vxlan tunnel should set dev->needed_headroom instead of
dev->hard_header_len, like what other ip tunnels do. This fixes
the above problem.
Cc: "David S. Miller" <davem@davemloft.net> Cc: stephen hemminger <stephen@networkplumber.org> Cc: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: Cong Wang <cwang@twopensource.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running RHEL6 userspace on a current upstream kernel, "ip link"
fails to show VF information.
The reason is a kernel<->userspace API change introduced by commit 88c5b5ce5cb57 ("rtnetlink: Call nlmsg_parse() with correct header length"),
after which the kernel does not see iproute2's IFLA_EXT_MASK attribute
in the netlink request.
iproute2 adjusted for the API change in its commit 63338dca4513
("libnetlink: Use ifinfomsg instead of rtgenmsg in rtnl_wilddump_req_filter").
The problem has been noticed before:
http://marc.info/?l=linux-netdev&m=136692296022182&w=2
(Subject: Re: getting VF link info seems to be broken in 3.9-rc8)
We can do better than tell those with old userspace to upgrade. We can
recognize the old iproute2 in the kernel by checking the netlink message
length. Even when including the IFLA_EXT_MASK attribute, its netlink
message is shorter than struct ifinfomsg.
With this patch "ip link" shows VF information in both old and new
iproute2 versions.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consider the scenario:
For a TCP-style socket, while processing the COOKIE_ECHO chunk in
sctp_sf_do_5_1D_ce(), after it has passed a series of sanity check,
a new association would be created in sctp_unpack_cookie(), but afterwards,
some processing maybe failed, and sctp_association_free() will be called to
free the previously allocated association, in sctp_association_free(),
sk_ack_backlog value is decremented for this socket, since the initial
value for sk_ack_backlog is 0, after the decrement, it will be 65535,
a wrap-around problem happens, and if we want to establish new associations
afterward in the same socket, ABORT would be triggered since sctp deem the
accept queue as full.
Fix this issue by only decrementing sk_ack_backlog for associations in
the endpoint's list.
Fix-suggested-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com> Acked-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey gave a AddressSanitizer[1] report that finally gave a good hint
at where was the origin of various problems already reported by Dormando
in the past [2]
Problem comes from the fact that UDP can have a lockless TX path, and
concurrent threads can manipulate sk_dst_cache, while another thread,
is holding socket lock and calls __sk_dst_set() in
ip4_datagram_release_cb() (this was added in linux-3.8)
It seems that all we need to do is to use sk_dst_check() and
sk_dst_set() so that all the writers hold same spinlock
(sk->sk_dst_lock) to prevent corruptions.
TCP stack do not need this protection, as all sk_dst_cache writers hold
the socket lock.
Fixes:ee45fd92c739
("sfc: Use TX PIO for sufficiently small packets")
The linux net driver uses memcpy_toio() in order to copy into
the PIO buffers.
Even on a 64bit machine this causes 32bit accesses to a write-
combined memory region.
There are hardware limitations that mean that only 64bit
naturally aligned accesses are safe in all cases.
Due to being write-combined memory region two 32bit accesses
may be coalesced to form a 64bit non 64bit aligned access.
Solution was to open-code the memory copy routines using pointers
and to only enable PIO for x86_64 machines.
Not tested on platforms other than x86_64 because this patch
disables the PIO feature on other platforms.
Compile-tested on x86 to ensure that works.
The WARN_ON_ONCE() code in the previous version of this patch
has been moved into the internal sfc debug driver as the
assertion was unnecessary in the upstream kernel code.
This bug fix applies to v3.13 and v3.14 stable branches.
Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ipv4_{update_pmtu,redirect} were called with tunnel's ifindex (t->dev is a
tunnel netdevice). It caused wrong route lookup and failure of pmtu update or
redirect. We should use the same ifindex that we use in ip_route_output_* in
*tunnel_xmit code. It is t->parms.link .
Signed-off-by: Dmitry Popov <ixaphire@qrator.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
unregister_netdevice_many() API is error prone and we had too
many bugs because of dangling LIST_HEAD on stacks.
See commit f87e6f47933e3e ("net: dont leave active on stack LIST_HEAD")
In fact, instead of making sure no caller leaves an active list_head,
just force a list_del() in the callee. No one seems to need to access
the list after unregister_netdevice_many()
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lars writes: "I'm only 99% sure that the net interfaces are qmi
interfaces, nothing to lose by adding them in my opinion."
And I tend to agree based on the similarity with the two Olicard
modems we already have here.
Reported-by: Lars Melin <larsm17@gmail.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fix typo in sparc codegen for SKF_AD_IFINDEX and SKF_AD_HATYPE
classic BPF extensions
Fixes: 2809a2087cc4 ("net: filter: Just In Time compiler for sparc") Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4a55530f38e4 (net: sh_eth: modify the definitions of register) managed
to leave out the E-DMAC register entries in sh_eth_offset_fast_sh3_sh2[], thus
totally breaking SH7619/771x support. Add the missing entries using the data
from before that commit.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current behaviour of the sh_eth driver is not to use the RNC bit
for the receive ring. This means that every packet recieved is not only
generating an IRQ but it also stops the receive ring DMA as well until
the driver re-enables it after unloading the packet.
This means that a number of the following errors are generated due to
the receive packet FIFO overflowing due to nowhere to put packets:
net eth0: Receive FIFO Overflow
Since feedback from Yoshihiro Shimoda shows that every supported LSI
for this driver should have the bit enabled it seems the best way is
to remove the RMCR default value from the per-system data and just
write it when initialising the RMCR value. This is discussed in
the message (http://www.spinics.net/lists/netdev/msg284912.html).
I have tested the RMCR_RNC configuration with NFS root filesystem and
the driver has not failed yet. There are further test reports from
Sergei Shtylov and others for both the R8A7790 and R8A7791.
There is also feedback fron Cao Minh Hiep[1] which reports the
same issue in (http://comments.gmane.org/gmane.linux.network/316285)
showing this fixes issues with losing UDP datagrams under iperf.
Tested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This bug is discovered by an recent F-RTO issue on tcpm list
https://www.ietf.org/mail-archive/web/tcpm/current/msg08794.html
The bug is that currently F-RTO does not use DSACK to undo cwnd in
certain cases: upon receiving an ACK after the RTO retransmission in
F-RTO, and the ACK has DSACK indicating the retransmission is spurious,
the sender only calls tcp_try_undo_loss() if some never retransmisted
data is sacked (FLAG_ORIG_DATA_SACKED).
The correct behavior is to unconditionally call tcp_try_undo_loss so
the DSACK information is used properly to undo the cwnd reduction.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now it is not possible to set mtu to team device which has a port
enslaved to it. The reason is that when team_change_mtu() calls
dev_set_mtu() for port device, notificator for NETDEV_PRECHANGEMTU
event is called and team_device_event() returns NOTIFY_BAD forbidding
the change. So fix this by returning NOTIFY_DONE here in case team is
changing mtu in team_change_mtu().
Introduced-by: 3d249d4c "net: introduce ethernet teaming device" Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Flavio Leitner <fbl@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I noticed we were sending wrong IPv4 ID in TCP flows when MTU discovery
is disabled.
Note how GSO/TSO packets do not have monotonically incrementing ID.
06:37:41.575531 IP (id 14227, proto: TCP (6), length: 4396)
06:37:41.575534 IP (id 14272, proto: TCP (6), length: 65212)
06:37:41.575544 IP (id 14312, proto: TCP (6), length: 57972)
06:37:41.575678 IP (id 14317, proto: TCP (6), length: 7292)
06:37:41.575683 IP (id 14361, proto: TCP (6), length: 63764)
It appears I introduced this bug in linux-3.1.
inet_getid() must return the old value of peer->ip_id_count,
not the new one.
Lets revert this part, and remove the prevention of
a null identification field in IPv6 Fragment Extension Header,
which is dubious and not even done properly.
Fixes: 87c48fa3b463 ("ipv6: make fragment identifications less predictable") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable the module alias hookup to allow tunnel modules to be autoloaded on demand.
This is in line with how most other netdev kinds work, and will allow userspace
to create tunnels without having CAP_SYS_MODULE.
Signed-off-by: Tom Gundersen <teg@jklm.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
br_handle_local_finish() is allowing us to insert an FDB entry with
disallowed vlan. For example, when port 1 and 2 are communicating in
vlan 10, and even if vlan 10 is disallowed on port 3, port 3 can
interfere with their communication by spoofed src mac address with
vlan id 10.
Note: Even if it is judged that a frame should not be learned, it should
not be dropped because it is destined for not forwarding layer but higher
layer. See IEEE 802.1Q-2011 8.13.10.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Any process is able to send netlink messages with leftover bytes.
Make the warning rate-limited to prevent too much log spam.
The warning is supposed to help find userspace bugs, so print the
triggering command name to implicate the buggy program.
[v2: Use pr_warn_ratelimited instead of printk_ratelimited.]
Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit efe4208 ("ipv6: make lookups simpler and faster") introduced a
regression in udp_v6_mcast_next(), resulting in multicast packets not
reaching the destination sockets under certain conditions.
The packet's IPv6 addresses are wrongly compared to the IPv6 addresses
from the function's socket argument, which indicates the starting point
for looping, instead of the loop variable. If the addresses from the
first socket do not match the packet's addresses, no socket in the list
will match.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is called from dcbnl_build_peer_app(). The "info"
struct isn't initialized at all so we disclose 2 bytes of uninitialized
stack data. We should clear it before passing it to the user.
Fixes: 48365e485275 ('qlcnic: dcb: Add support for CEE Netlink interface.') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was possible to get a setuid root or setcap executable to write to
it's stdout or stderr (which has been set made a netlink socket) and
inadvertently reconfigure the networking stack.
To prevent this we check that both the creator of the socket and
the currentl applications has permission to reconfigure the network
stack.
Unfortunately this breaks Zebra which always uses sendto/sendmsg
and creates it's socket without any privileges.
To keep Zebra working don't bother checking if the creator of the
socket has privilege when a destination address is specified. Instead
rely exclusively on the privileges of the sender of the socket.
Note from Andy: This is exactly Eric's code except for some comment
clarifications and formatting fixes. Neither I nor, I think, anyone
else is thrilled with this approach, but I'm hesitant to wait on a
better fix since 3.15 is almost here.
Note to stable maintainers: This is a mess. An earlier series of
patches in 3.15 fix a rather serious security issue (CVE-2014-0181),
but they did so in a way that breaks Zebra. The offending series
includes:
net: Add variants of capable for use on netlink messages
If a given kernel version is missing that series of fixes, it's
probably worth backporting it and this patch. if that series is
present, then this fix is critical if you care about Zebra.
Cc: stable@vger.kernel.org Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible by passing a netlink socket to a more privileged
executable and then to fool that executable into writing to the socket
data that happens to be valid netlink message to do something that
privileged executable did not intend to do.
To keep this from happening replace bare capable and ns_capable calls
with netlink_capable, netlink_net_calls and netlink_ns_capable calls.
Which act the same as the previous calls except they verify that the
opener of the socket had the desired permissions as well.
Reported-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
netlink_net_capable - The common case use, for operations that are safe on a network namespace
netlink_capable - For operations that are only known to be safe for the global root
netlink_ns_capable - The general case of capable used to handle special cases
__netlink_ns_capable - Same as netlink_ns_capable except taking a netlink_skb_parms instead of
the skbuff of a netlink message.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>