[media] s5p-fimc: Convert to use media pipeline operations
In the camera capture driver use fimc_pipeline_* calls provided by
the media device driver part, in place where v4l2_subdev_call() were
used. This way the capture driver don't need to differentiate between
various H/W pipeline setups, i.e. if the MIPI-CSI receiver subdev is
used or not.
Remove the sync_capture_fmt() function instead of which
fimc_pipeline_try_format() is introduced in the following patch adding
the FIMC capture subdev.
The TRY_FMT ioctl function is completed by a subsequent patch adding
the capture subdev, so the try_fmt routines can be reused in the subdev
and the video node ioctl handlers.
[media] s5p-fimc: Correct color format enumeration
Replace fimc_find_format() and find_mbus_format() with single function
that can return a pointer to the private format description based
on fourcc, media bus code or index in the table.
Create separate VIDIOC_ENUM_FMT ioctl handlers for video capture
and mem-to-mem video node. This is needed because some formats are
valid only for the video capture and some only for the mem-to-mem
video node.
[media] s5p-fimc: Convert to the new control framework
Convert the v4l controls code to use the new control framework.
fimc_ctrls_activate/deactivate functions are introduced for the
transparent DMA transfer mode (JPEG), where the rotation and flipping
controls are not supported.
The capture video node does not inherit sensors' controls when the
subdevs are configured by the user space (user_subdev_api == true).
However by default after the driver's initialization
the 'user-subdev_api' flag is false and any sensor controls will
also be available at the video node.
When the pipeline links are disconnected through the media device
the FIMC and any sensor inherited controls are destroyed and then
again created when the pipeline connection completes.
[media] s5p-fimc: Conversion to use struct v4l2_fh
This is a prerequisite for the patch converting the driver to use
the control framework. As the capture driver does not use per file
handle contexts, two separate ioctl handlers are created for it
(vidioc_try_fmt_mplane, and vidioc_g_fmt_mplane) so there is no
handlers shared between the memory-to-memory and capture video node.
Add a top level media device driver aggregating FIMC video devnodes,
MIPI-CSIS and sensor subdevs. This driver gathers all media entities
and creates the possible links between them during initialization. By
default some links will be activated to enable access to all available
sensors in the system. For example if there are sensors S0, S1 listed
in the media device platform data definition they will be by default
assigned to FIMC0, FIMC1 respectively, which in turn will corresponds
to separate /dev/video?.
There is enough FIMC H/W entities to cover all available physical camera
interfaces in the system.
The fimc media device driver is bound to the "s5p-fimc-md" platform device.
Such platform device should be created by board initialization code
and camera sensors description array need to be specified as its
platform data.
The media device driver also implements various video pipeline operations,
for enabling subdevs power, streaming, etc., which will be used by the
capture video node driver.
[media] s5p-fimc: Remove v4l2_device from video capture and m2m driver
Currently there is a v4l2_device instance being registered per each
(capture and memory-to-memory) video node created per FIMC H/W instance.
This patch is a prerequisite for using the top level v4l2_device
instantiated by the media device driver.
To retain current debug trace semantic (so it's possible to distinguish
between the capture and m2m FIMC) the video_device is used in place
of v4l2_device where appropriate.
[media] s5p-fimc: Remove sensor management code from FIMC capture driver
The sensor subdevs need to be shared between all available FIMC instances.
Remove their registration from FIMC capture driver so they can then be
registered to the media device driver.
[media] s5p-fimc: Limit number of available inputs to one
The current driver allowed camera sensors to be used only with single
FIMC H/W instance, FIMC0..FIMC2/3, designated at compile time. Remaining FIMC
entities could be used for video processing only, as mem-to-mem devices.
Required camera could be selected with S_INPUT ioctl at one devnode only.
However in that case it was not possible to use both cameras independently
at the same time, as all sensors were registered to single FIMC capture
driver. In most recent S5P SoC version there is enough FIMC H/W instances
to cover all physical camera interfaces.
Each FIMC instance exports its own video devnode. Thus we distribute
the camera sensors one per each /dev/video? by default. It will allow to
use both camera simultaneously by opening different video node.
The camera sensors at FIMC are now not selected with S_INPUT ioctl, there
is one input only available per /dev/video?.
By default a single sensor is connected at FIMC input as specified by the
media device platform data subdev description table. This assignment
can be changed at runtime through the pipeline reconfiguration at the media
device level.
There are 2 separate clock outputs available in the SoC for external sensors.
These two clocks can be shared among all FIMC entities and there is
currently no any arbitration of the clocks in the driver.
So make the capture driver not touching these clocks and let them be
be properly handled at the media device driver level, enabling proper
arbitration between FIMC entities.
[media] s5p-fimc: Remove registration of video nodes from probe()
Do not register video nodes during FIMC device probe. Also make
fimc_register_m2m_device() public for use by the media device driver.
The video nodes are to be registered during the media device driver
initialization, altogether with the subdev devnodes. The video
capture nodes need to be registered as last ones when the remaining
pipeline elements are already initialized.
Add intialization of the media entities for video capture
and mem-to-mem video nodes. The mem-to-mem entity has no pads
whereas the capture entity has single sink pad.
Also clean up the video node naming for consistency.
[media] s5p-csis: Rework the system suspend/resume helpers
Do not resume the device during system resume if it was idle
before system suspend, as this causes resume from suspend
to RAM failures on Exynos4. For this purpose runtime PM and
system sleep helpers are separated.
[media] s5p-csis: Handle all available power supplies
On the SoCs this driver is intended to support the are three separate
pins to supply the MIPI-CSIS subsystem: 1.1V or 1.2V, 1.8V and power
supply for an internal PLL.
This patch adds support for two separate voltage supplies to cover
properly board configurations where PMIC requires to configure
independently each external supply of the MIPI-CSI device. The 1.8V
and PLL supply are assigned a single "vdd18" regulator supply name
as it seems more reasonable than creating separate regulator supplies
for them.
While at here stop using the 'fixed_phy_vdd' platform_data field.
It has been introduced for boards where the MIPI-CSIS supplies are
not controllable. However it is not needed as those boards can use
the dummy regulator.
[media] s5p-fimc: Add runtime PM support in the mem-to-mem driver
Add runtime PM and system sleep support in the memory-to-memory
driver. It's required to enable the FIMC operation on Exynos4
SoCs. This patch prevents system boot failure when the driver
is compiled in, as it now tries to access its I/O memory without
first enabling the corresponding power domain.
The camera capture device suspend/resume is not fully covered,
the capture device is just powered on/off during the video
node open/close. However this enables it's normal operation
on Exynos4 SoCs.
[mchehab@redhat.com: fix a small checkpatch error] Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Marek Szyprowski [Mon, 29 Aug 2011 11:51:49 +0000 (08:51 -0300)]
[media] media: vb2: change queue initialization order
This patch changes the order of operations during stream on call. Now the
buffers are first queued to the driver and then the start_streaming method
is called.
This resolves the most common case when the driver needs to know buffer
addresses to enable dma engine and start streaming. Additional parameter
to start_streaming method have been added to simplify drivers code. The
driver are now obliged to check if the number of queued buffers is high
enough to enable hardware streaming. If not - it can return an error. In
such case all the buffers that have been pre-queued are invalidated.
This patch also updates all videobuf2 clients to work properly with the
changed order of operations.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Pawel Osciak <pawel@osciak.com> CC: Guennadi Liakhovetski <g.liakhovetski@gmx.de> CC: Hans Verkuil <hverkuil@xs4all.nl> CC: Tomasz Stanislawski <t.stanislaws@samsung.com> CC: Sylwester Nawrocki <s.nawrocki@samsung.com> CC: Kamil Debski <k.debski@samsung.com> CC: Jonathan Corbet <corbet@lwn.net> CC: Josh Wu <josh.wu@atmel.com> CC: Hans de Goede <hdegoede@redhat.com> CC: Paul Mundt <lethal@linux-sh.org> Tested-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Marek Szyprowski [Mon, 29 Aug 2011 06:20:56 +0000 (03:20 -0300)]
[media] media: vb2: dma contig allocator: use dma_addr instread of paddr
Use the correct 'dma_addr' name for the buffer address. 'paddr' suggested
that this is the physical address in system memory. For most ARM platforms
these two are the same, but this is not a generic rule. 'dma_addr' will
also point better to dma-mapping api.
Marek Szyprowski [Wed, 24 Aug 2011 09:43:36 +0000 (06:43 -0300)]
[media] media: vb2: change plane sizes array to unsigned int[]
Plane sizes array was declared as unsigned long[], while unsigned int is
more than enough for storing size of the video buffer. This patch reduces
the size of the array by definiting it as unsigned int[].
Marek Szyprowski [Wed, 24 Aug 2011 09:49:35 +0000 (06:49 -0300)]
[media] media: vb2: fix handling MAPPED buffer flag
MAPPED flag was set for the buffer only if all it's planes were mapped and
relied on a simple mapping counter. This assumption is really bogus,
especially because the buffers may be mapped multiple times. Also the
meaning of this flag for muliplane buffers was not really useful. This
patch fixes this issue by setting the MAPPED flag for the buffer if any of
it's planes is in use (what means that has been mapped at least once), so
MAPPED flag can be used as 'in_use' indicator.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Pawel Osciak <pawel@osciak.com> Tested-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Marek Szyprowski [Wed, 24 Aug 2011 09:36:26 +0000 (06:36 -0300)]
[media] media: vb2: add a check if queued userptr buffer is large enough
Videobuf2 accepted any userptr buffer without verifying if its size is
large enough to store the video data from the driver. The driver reports
the minimal size of video data once in queue_setup and expects that
videobuf2 provides buffers that match these requirements. This patch
adds the required check.
Hans Verkuil [Thu, 25 Aug 2011 13:10:32 +0000 (10:10 -0300)]
[media] mxl5005s: fix compiler warning
Removed the unused Xtal_Int variable. That made it also possible to remove a
related function. However, the code of that function has been preserved in a
comment describing an equation. Without that function that comment would
have been hard to understand.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Joe Perches [Sun, 21 Aug 2011 22:56:50 +0000 (19:56 -0300)]
[media] et61x251: Use current logging styles
Add pr_fmt and convert printks to pr_<level>
Remove explicit prefixes from logging messages.
One of the prefixes was defective, a copy/paste error.
Use ##__VA_ARGS__ for variadic macros.
Whitespace neatening.
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Joe Perches [Sun, 21 Aug 2011 22:56:48 +0000 (19:56 -0300)]
[media] bt8xx: Use current logging styles
This converts some messages that were emitted at
KERN_INFO to KERN_DEBUG. All of these messages
were guarded by bttv_debug tests.
Add pr_fmt.
Convert printks to pr_<level>
Convert printks without KERN_<level> to appropriate pr_<level>.
Removed embedded prefixes when pr_fmt was added.
Whitespace cleanups when around other conversions.
Macros coded with if statements should be do { if... } while (0)
so the macros can be used in other if tests.
Use ##__VA_ARGS__ for variadic macro as well.
Coalesce format strings.
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Joe Perches [Sun, 21 Aug 2011 22:56:44 +0000 (19:56 -0300)]
[media] saa7146: Use current logging styles
Standardize the mechanisms to emit logging messages.
A few other modules used an #include from saa7146,
convert those at the same time.
Add pr_fmt.
Convert printks to pr_<level>
Convert printks without KERN_<level> to appropriate pr_<level>.
Convert logging macros requiring multiple parentheses to normal style.
Removed embedded prefixes when pr_fmt was added.
Whitespace cleanups when around other conversions.
Use printf extension %pM to print mac address.
Coalesce format strings.
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Michael Hunold <michael@mihu.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Chris Rankin [Sat, 20 Aug 2011 19:01:26 +0000 (16:01 -0300)]
[media] em28xx: don't sleep on disconnect
The DVB framework will try to power-down an adapter that no-one is using
any more, but this assumes that the adapter is still connected to the
machine. That's not always true for a USB adapter, so disable the sleep
operations when the adapter has been physically unplugged.
This prevents I2C write failures with error -19 from appearing
occasionally in the dmesg log.
Signed-off-by: Chris Rankin <rankincj@yahoo.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Chris Rankin [Sat, 20 Aug 2011 11:28:17 +0000 (08:28 -0300)]
[media] em28xx: clean up resources should init fail
This patch ensures that the em28xx_init_dev() function cleans up after itself,
in the event that it fails. This isimportant because the struct em28xx will be
deallocated if em28xx_init_dev() returns an error.
[mchehab@redhat.com: Fix merge conflicts and simplify the goto labels] Signed-off-by: Chris Rankin <rankincj@yahoo.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Chris Rankin [Sat, 20 Aug 2011 11:21:03 +0000 (08:21 -0300)]
[media] em28xx: use atomic bit operations for devices-in-use mask
Use atomic bit operations for the em28xx_devused mask, to prevent an
unlikely race condition should two adapters be plugged in
simultaneously. The operations also clearer than explicit bit
manipulation anyway.
Signed-off-by: Chris Rankin <rankincj@yahoo.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] DVB: dvb_frontend: remove static assignments from dtv_property_cache_sync()
dtv_property_cache_init().
dtv_property_process_get().
overwritten with invalid values, leading to partially incorrect
results when calling FE_GET_PROPERTY.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
kbuild: introduce ccflags-y, asflags-y and ldflags-y
Moreover, these flags (at least EXTRA_CFLAGS) have been documented for command
line use. By default, gmake(1) do not override command line setting, so this is
likely to result in build failure or unexpected behavior.
Replace their usage by Kbuild's `{as,cc,ld}flags-y'.
Chris Rankin [Sun, 14 Aug 2011 12:18:46 +0000 (09:18 -0300)]
[media] Add missing OK key to PCTV IR keymap
Hi,
The following patch adds the IR code for the missing "OK" key to the Pinnacle
PCTV HD map. This map is now used by the PCTV 290e DVB-T2 device, whose remote
control has 26 buttons.
Steve Kerrison [Tue, 9 Aug 2011 10:16:21 +0000 (07:16 -0300)]
[media] CXD2820R: Replace i2c message translation with repeater gate control
This patch implements an i2c_gate_ctrl op for the cxd2820r. Thanks to Robert
Schlabbach for identifying the register address and field to set.
The old i2c intercept code that prefixed messages with a passthrough byte has
been removed and the PCTV nanoStick T2 290e entry in em28xx-dvb has been
updated appropriately.
Tested for DVB-T2 use; I would appreciate it if somebody with DVB-C capabilities
could test it as well - from inspection I cannot see any problems.
This is patch v2. It fixes some schoolboy style errors and removes superfluous
i2c entries in cxd2820r.h.
Signed-off-by: Steve Kerrison <steve@stevekerrison.com> Acked-by: Antti Palosaari <crope@iki.fi> Tested-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] DVB: improve documentation for satellite delivery systems
- Move voltage and tone to DVB-S.
- Add turbo code.
- In DVB-S2 and turbo code sections, refer to DVB-S, as both
are extensions to DVB-S.
- Add modulation to DVB-S2.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tuners in general convert a high frequency carrier into an Intermediate
Frequency (IF).
Digital tuners like tda18271, xc3028, etc. generally allow changing the IF
frequency, although they generally have recommented settings for the IF.
Analog tuners, have a fixed IF frequency, that depends on the physical
characteristics of some analog components.
For digital tuners, it makes sense to have ways to configure IF,
via the tuner's configuration structure, like what's done inside the
tda18271-fe maps.
The demods need to know what IF is used by the tuner, as it will need
to convert internally from IF into baseband. Currently, the bridge driver
needs to fill a per-demod configuration struct for it, or pass it via
a dvb_attach parameter.
The tda18271 datasheet recommends to use different IF's for different
delivery system types and for different bandwidths.
The DRX-K demod also needs to know the IF frequency in order to work,
just like all other demods. However, as it accepts different delivery
systems (DVB-C and DVB-T), the IF may change if the standard and/or
bandwidth is changed.
So, the usual procedure of passing it via a config struct doesn't work.
One might try to code it as two separate IF frequencies, or even as a
table in function of the delivery system and the bandwidth, but this
will be messy.
So, it is better and simpler to just add a new callback for it and
require the tuners that can be used with MFE frontends like drx-k
to implement a new callback to return the used IF.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Acked-by: Antti Palosaari <crope@iki.fi>
Jarod Wilson [Thu, 14 Jul 2011 22:06:08 +0000 (19:06 -0300)]
[media] em28xx: add em28xx_ prefix to functions
Makes it more straight-forward to follow stack traces if the functions
don't have generic names. Using this as a crutch while trying to better
understand the lockdep warnings I get when loading the em28xx driver.
Jonathan Corbet [Thu, 14 Jul 2011 21:10:44 +0000 (18:10 -0300)]
[media] videobuf2: Do not unconditionally map S/G buffers into kernel space
The one in-tree videobuf2-dma-sg driver (mmp-camera) has no need for a
kernel-space mapping of the buffers; one suspects that most other drivers
would not either. The videobuf2-dma-sg module does the right thing if
buf->vaddr == NULL - it maps the buffer on demand if somebody needs it. So
let's not map the buffer at allocation time; that will save a little CPU
time and a lot of address space in the vmalloc range.
Signed-off-by: Jonathan Corbet <corbet@lwn.net> Acked-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] DVB: dvb_frontend: update locking in dvb_frontend_{add, get_event}
- fepriv->parameters_out isn't protected by events->mtx, so
move the call to fe->ops.get_frontend out of the locked area.
- move the assignment of e->status into the locked area.
- use direct assignment instead of memcpy.
- use mutex_lock instead of mutex_lock_interruptible, because
all code paths protected by this mutex won't block.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dev->int_in USB interfaces is used by some devices for the
Remote Controller. Not all devices seem to define this interface,
so, tm6000_reset should not try to set the interface to it on
such devices.
Thierry Reding [Thu, 4 Aug 2011 07:14:11 +0000 (04:14 -0300)]
[media] tm6000: Properly count device usage
When the USB device is disconnected, the device usage bit is not cleared
properly. This leads to errors when a device is unplugged and replugged
several times until all TM6000_MAXBOARDS bits are used and keeps the
driver from binding to the device.
Thierry Reding [Thu, 4 Aug 2011 07:14:10 +0000 (04:14 -0300)]
[media] tm6000: Add locking for USB transfers
This commit introduces the usb_lock mutex to ensure that a USB request
always gets the proper response. While this is currently not really
necessary it will become important as there are more users.
Thierry Reding [Thu, 4 Aug 2011 07:14:09 +0000 (04:14 -0300)]
[media] tm6000: Rework standard register tables
This commit uses sentinel entries to terminate the TV standard register
tables instead of hard-coding their size, allowing further entries to be
added more easily. It is also more space-efficient if the tables have a
varying number of entries.
Thierry Reding [Thu, 4 Aug 2011 07:14:08 +0000 (04:14 -0300)]
[media] tm6000: Disable video interface in radio mode
Video data is useless in radio mode, so the corresponding interface can
be safely disabled. This should reduce the amount of isochronous traffic
noticeably.
projects / linux-beck.git / log