Dell Inspiron 1525 seems to have a buggy BIOS setup and screws up
the recent codec parser, as reported by Oleksandr Natalenko:
http://lkml.org/lkml/2008/9/12/203
This patch adds the working model, dell-3stack, statically.
Jean Delvare [Tue, 30 Sep 2008 09:40:37 +0000 (11:40 +0200)]
ALSA: ASoC: Fix cs4270 error path
The error path in cs4270_probe/cs4270_remove is pretty broken:
* If cs4270_probe fails, codec is leaked.
* If snd_soc_register_card fails, cs4270_i2c_driver stays registered.
* If I2C support is enabled but no I2C device is found, i2c_del_driver
is never called (neither in cs4270_probe nor in cs4270_remove.
Fix all 3 problems by implementing a clean error path in cs4270_probe
and jumping to its labels as needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Timur Tabi [Tue, 29 Jul 2008 21:35:52 +0000 (16:35 -0500)]
ALSA: make the CS4270 driver a new-style I2C driver
Update the CS4270 ALSA device driver to use the new-style I2C interface.
Starting with the 2.6.27 PowerPC kernel, I2C devices that have entries in the
device trees can no longer be probed by old-style I2C drivers. The device
tree for Freescale MPC8610 HPCD has included an entry for the CS4270 since
2.6.25, but that entry was previously ignored by the PowerPC I2C subsystem.
Since that's no longer the case, the best solution is to update the CS4270
driver to a new-style interface, rather than try to revert the behavior of
new PowerPC I2C subsystem.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA: fix locking in snd_pcm_open*() and snd_rawmidi_open*()
The PCM and rawmidi open callbacks have a lock against card->controls_list
but it takes a wrong one, card->controls_rwsem, instead of a right one
card->ctl_files_rwlock. This patch fixes them.
This change also fixes automatically the potential deadlocks due to
mm->mmap_sem in munmap and copy_from/to_user, reported by Sitsofe
Wheeler:
CONFIG_AC97_BUS is used from both sound and ucb1400 drivers.
The recent change in Kconfig introduced the exclusive dependency on
CONFIG_SOUND, and disabled the ucb1400 build without sound.
This patch makes CONFIG_AC97_BUS independent.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Clemens Ladisch [Fri, 29 Aug 2008 11:08:34 +0000 (13:08 +0200)]
ALSA: oxygen: fix distorted output on AK4396-based cards
When changing the sample rate, the CMI8788's master clock output becomes
unstable for a short time. The AK4396 needs the master clock to do SPI
writes, so writing to an AK4396 control register directly after a sample
rate change will garble the value. In our case, this leads to the DACs
being misconfigured to I2S sample format, which results in a wrong
output level and horrible distortions on samples louder than -6 dB.
To fix this, we need to wait until the new master clock signal has
become stable before doing SPI writes.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch introduced a wrong detection of other intel Macs with
ALC88* codec because they share the same PCI SSID (but have different
codec subsystem-IDs). See http://lkml.org/lkml/2008/8/24/143
Jarkko Nikula [Tue, 26 Aug 2008 10:32:57 +0000 (13:32 +0300)]
ALSA: ASoC: Fix error paths in N810 machine driver init and release clocks at exit
Thanks to Felipe Balbi <felipe.balbi@nokia.com> by noticing that if clk_get
to sys_clkout2_src fails, then n810_snd_device is never released.
Add also sys_clkout2_src release into error path, error code return and
release the clocks at exit.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yitchak Gertner [Mon, 25 Aug 2008 22:27:06 +0000 (15:27 -0700)]
bnx2x: Multi Queue
The multi queue support is still disabled by default for the bnx2x
(needs some more testing and validation), but there are 2 obvious bug in
it which are fixed in this patch
Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yitchak Gertner [Mon, 25 Aug 2008 22:26:24 +0000 (15:26 -0700)]
bnx2x: NAPI and interrupts enable/disable
Fixing the order of enabling and disabling NAPI and the interrupts
Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yitchak Gertner [Mon, 25 Aug 2008 22:25:45 +0000 (15:25 -0700)]
bnx2x: NIC load failure cleanup
Load failures were not handled correctly
Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yitchak Gertner [Mon, 25 Aug 2008 22:24:21 +0000 (15:24 -0700)]
bnx2x: Initialization structure
The TPA initialization is part of the FW internal memory initialization
and so it is moved to the appropriate function
Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Mon, 25 Aug 2008 22:19:17 +0000 (15:19 -0700)]
bnx2x: Rx work check
The has Rx work check was wrong: when the FW was at the end of the page,
the driver was already at the beginning of the next page. Since the
check only validated that both driver and FW are pointing to the same
place, it concluded that there is still work to be done. This caused
some serious issues including long latency results on ping-pong test and
lockups while unloading the driver in that condition.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Mon, 25 Aug 2008 22:16:19 +0000 (15:16 -0700)]
sctp: add verification checks to SCTP_AUTH_KEY option
The structure used for SCTP_AUTH_KEY option contains a
length that needs to be verfied to prevent buffer overflow
conditions. Spoted by Eugene Teo <eteo@redhat.com>.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allowing 4k CPU's is not practical at this time, because we still have a
number of places that have several 'cpumask_t's on the stack, and a
4k-bit cpumask is 512 bytes of stack-space for each such variable. This
literally caused functions like 'smp_call_function_mask' to have a 2.5kB
stack frame, and several functions to have 2kB stackframes.
With an 8kB stack total, smashing the stack was simply much too likely.
At least bugzilla entry
http://bugzilla.kernel.org/show_bug.cgi?id=11342
was due to this.
The earlier commit to not inline load_module() into sys_init_module()
fixed the particular symptoms of this that Alan Brunelle saw in that
bugzilla entry, but the huge stack waste by cpumask_t's was the more
direct cause.
Some day we'll have allocation helpers that allocate large CPU masks
dynamically, but in the meantime we simply cannot allow cpumasks this
large.
Cc: Alan D. Brunelle <Alan.Brunelle@hp.com> Cc: Mike Travis <travis@sgi.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 25 Aug 2008 18:26:33 +0000 (11:26 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: add X86_FEATURE_XMM4_2 definitions
x86: fix cpufreq + sched_clock() regression
x86: fix HPET regression in 2.6.26 versus 2.6.25, check hpet against BAR, v3
x86: do not enable TSC notifier if we don't need it
x86 MCE: Fix CPU hotplug problem with multiple multicore AMD CPUs
x86: fix: make PCI ECS for AMD CPUs hotplug capable
x86: fix: do not run code in amd_bus.c on non-AMD CPUs
Linus Torvalds [Mon, 25 Aug 2008 18:25:10 +0000 (11:25 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: fix reference leak in pci_get_dev_by_id()
PCI: shpchp: Rename duplicate slot name N as N-1, N-2, N-M...
PCI: pciehp: Rename duplicate slot name N as N-1, N-2, N-M...
Linus Torvalds [Mon, 25 Aug 2008 18:24:51 +0000 (11:24 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ASoC: Fix double free and memory leak in many codec drivers
ALSA: CA0106 on MSI K8N Diamond PLUS Motherboard
Linus Torvalds [Mon, 25 Aug 2008 18:19:53 +0000 (11:19 -0700)]
Merge branch 'kvm-updates-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm
* 'kvm-updates-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: fix userspace ABI breakage
KVM: MMU: Fix torn shadow pte
KVM: Use .fixup instead of .text.fixup on __kvm_handle_fault_on_reboot
Linus Torvalds [Mon, 25 Aug 2008 18:10:26 +0000 (11:10 -0700)]
[module] Don't let gcc inline load_module()
'load_module()' is a complex function that contains all the ELF section
logic, and inlining it is utterly insane. But gcc will do it, simply
because there is only one call-site. As a result, all the stack space
that is allocated for all the work to load the module will still be
active when we actually call the module init sequence, and the deep call
chain makes stack overflows happen.
And stack overflows are really hard to debug, because they not only
corrupt random pages below the stack, but also corrupt the thread_info
structure that is allocated under the stack.
In this case, Alan Brunelle reported some crazy oopses at bootup, after
loading the processor module that ends up doing complex ACPI stuff and
has quite a deep callchain. This should fix it, and is the sane thing
to do regardless.
Cc: Alan D. Brunelle <Alan.Brunelle@hp.com> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Zijlstra [Mon, 25 Aug 2008 15:15:34 +0000 (17:15 +0200)]
sched_clock: fix cpu_clock()
This patch fixes 3 issues:
a) it removes the dependency on jiffies, because jiffies are incremented
by a single CPU, and the tick is not synchronized between CPUs. Therefore
relying on it to calculate a window to clip whacky TSC values doesn't work
as it can drift around.
So instead use [GTOD, GTOD+TICK_NSEC) as the window.
Adrian Bunk [Tue, 5 Aug 2008 22:36:09 +0000 (01:36 +0300)]
KVM: fix userspace ABI breakage
The following part of commit 9ef621d3be56e1188300476a8102ff54f7b6793f
(KVM: Support mixed endian machines) changed on the size of a struct
that is exported to userspace:
Eduardo Habkost [Tue, 19 Aug 2008 23:00:08 +0000 (20:00 -0300)]
KVM: Use .fixup instead of .text.fixup on __kvm_handle_fault_on_reboot
vmlinux.lds expects the fixup code to be on a section named .fixup. The
.text.fixup section is not mentioned on vmlinux.lds, and is included on
the resulting vmlinux (just after .text) only because of ld heuristics on
placing orphan sections.
However, placing .text.fixup outside .text breaks the definition of
_etext, making it exclude the .text.fixup contents. That makes .text.fixup
be ignored by the kernel initialization code that needs to know about
section locations, such as the code setting page protection bits.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
Anthony Liguori [Mon, 18 Aug 2008 22:15:31 +0000 (17:15 -0500)]
virtio_balloon: fix towards_target when deflating balloon
Both v and vb->num_pages are u32 and unsigned int respectively. If v is less
than vb->num_pages (and it is, when deflating the balloon), the result is a
very large 32-bit number. Since we're returning a s64, instead of getting the
same negative number we desire, we get a very large positive number.
This handles the case where v < vb->num_pages and ensures we get a small,
negative, s64 as the result.
Rusty: please push this for 2.6.27-rc4. It's probably appropriate for the
stable tree too as it will cause an unexpected OOM when ballooning.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (simplified)
Jean Delvare [Mon, 25 Aug 2008 10:49:20 +0000 (11:49 +0100)]
ALSA: ASoC: Fix double free and memory leak in many codec drivers
Many SoC audio codec drivers have improper freeing of memory in error
paths.
* codec is allocated in the platform device probe function, but is not
freed there in case of error. Instead it is freed in the i2c device
probe function's error path. However the success or failure of both
functions is not linked, so this could result in a double free (if
the platform device is successfully probed, the i2c device probing
fails and then the platform driver is unregistered.)
* codec->private_data is allocated in many platform device probe
functions but not freed in their error paths.
This patch hopefully solves all these problems.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yinghai Lu [Mon, 25 Aug 2008 07:56:08 +0000 (00:56 -0700)]
x86: fix HPET regression in 2.6.26 versus 2.6.25, check hpet against BAR, v3
David Witbrodt tracked down (and bisected) a hpet bootup hang on his
system to the following problem: a BIOS bug made the hpet device
visible as a generic PCI device. If e820 reserved entries happen to
be registered first in the resource tree [which v2.6.26 started doing],
then the PCI code will reallocate that device's BAR to some other
address - breaking timer IRQs and hanging the system.
( Normally hpet devices are hidden by the BIOS from the OS's PCI
discovery via chipset magic. Sometimes the hpet is not a PCI device
at all. )
Solve this fundamental fragility by making non-PCI platform drivers
insert resources into the resource tree even if it overlaps the e820
reserved entry, to keep the resource manager from updating the BAR.
Also do these checks for the ioapic and mmconfig addresses, and emit
a warning if this happens.
Bisected-by: David Witbrodt <dawitbro@sbcglobal.net> Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com> Tested-by: David Witbrodt <dawitbro@sbcglobal.net> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Travis Place [Mon, 25 Aug 2008 06:11:50 +0000 (08:11 +0200)]
ALSA: CA0106 on MSI K8N Diamond PLUS Motherboard
Correct a previous patch for the ca0106 onboard the MSI K8N Diamond PLUS
motherboard. Confirmed to have Line/Mic/Aux working for input, and sound
output working as expected.
Signed-off-by: Travis Place <wishie@wishie.net> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Arjan van de Ven [Sun, 24 Aug 2008 04:45:21 +0000 (21:45 -0700)]
Fix oops in acer_wmi driver (acer_wmi_init)
The acer_wmi driver does a DMI scan for quirks, and then sets flags into the
"interface" datastructure for some cases. However, the quirks happen real early
before "interface" is per se initialized from NULL.
The patch below 1) adds a NULL pointer check and 2) (re)runs the quirks at the
end, when "interface" has it's final value.
Reported-by: kerneloops.org Acked-by: Carlos Corbacho <carlos@strangeworlds.co.uk> CC: stable@vger.kernel.org Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ipv6: protocol for address routes
icmp: icmp_sk() should not use smp_processor_id() in preemptible code
pkt_sched: Fix qdisc list locking
pkt_sched: Fix qdisc_watchdog() vs. dev_deactivate() race
sctp: fix potential panics in the SCTP-AUTH API.
x86 MCE: Fix CPU hotplug problem with multiple multicore AMD CPUs
During CPU hot-remove the sysfs directory created by
threshold_create_bank(), defined in
arch/x86/kernel/cpu/mcheck/mce_amd_64.c, has to be removed before
its parent directory, created by mce_create_device(), defined in
arch/x86/kernel/cpu/mcheck/mce_64.c . Moreover, when the CPU in
question is hotplugged again, obviously the latter has to be created
before the former. At present, the right ordering is not enforced,
because all of these operations are carried out by CPU hotplug
notifiers which are not appropriately ordered with respect to each
other. This leads to serious problems on systems with two or more
multicore AMD CPUs, among other things during suspend and hibernation.
Fix the problem by placing threshold bank CPU hotplug callbacks in
mce_cpu_callback(), so that they are invoked at the right places,
if defined. Additionally, use kobject_del() to remove the sysfs
directory associated with the kobject created by
kobject_create_and_add() in threshold_create_bank(), to prevent the
kernel from crashing during CPU hotplug operations on systems with
two or more multicore AMD CPUs.
This patch fixes bug #11337.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Andi Kleen <andi@firstfloor.org> Tested-by: Mark Langsdorf <mark.langsdorf@amd.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Robert Richter [Fri, 22 Aug 2008 18:23:37 +0000 (20:23 +0200)]
x86: fix: do not run code in amd_bus.c on non-AMD CPUs
Jan Beulich wrote:
> Even worse - this would even try to access the MSR on non-AMD CPUs
> (currently probably prevented just by the fact that only AMD ones use
> family values of 0x10 or higher).
This patch adds cpu vendor check to the postcore_initcalls.
Reported-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Robert Richter <robert.richter@amd.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
This fixes a problem spotted with zebra, but not sure if it is
necessary a kernel problem. With IPV6 when an address is added to an
interface, Zebra creates a duplicate RIB entry, one as a connected
route, and other as a kernel route.
When an address is added to an interface the RTN_NEWADDR message
causes Zebra to create a connected route. In IPV4 when an address is
added to an interface a RTN_NEWROUTE message is set to user space with
the protocol RTPROT_KERNEL. Zebra ignores these messages, because it
already has the connected route.
The problem is that route created in IPV6 has route protocol ==
RTPROT_BOOT. Was this a design decision or a bug? This fixes it. Same
patch applies to both net-2.6 and stable.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
BUG: using smp_processor_id() in preemptible [00000000] code: tracepath/3205
caller is icmp_sk+0x15/0x30
Pid: 3205, comm: tracepath Not tainted 2.6.27-rc4 #1
Linus Torvalds [Fri, 22 Aug 2008 15:37:07 +0000 (08:37 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: Update documentation to remind users to update mke2fs.conf
ext4: Fix small file fragmentation
ext4: Initialize writeback_index to 0 when allocating a new inode
ext4: make sure ext4_has_free_blocks returns 0 for ENOSPC
ext4: journal credit fix for the delayed allocation's writepages() function
ext4: Rework the ext4_da_writepages() function
ext4: journal credits reservation fixes for DIO, fallocate
ext4: journal credits reservation fixes for extent file writepage
ext4: journal credits calulation cleanup and fix for non-extent writepage
ext4: Fix bug where we return ENOSPC even though we have plenty of inodes
ext4: don't try to resize if there are no reserved gdt blocks left
ext4: Use ext4_discard_reservations instead of mballoc-specific call
ext4: Fix ext4_dx_readdir hash collision handling
ext4: Fix delalloc release block reservation for truncate
ext4: Fix potential truncate BUG due to i_prealloc_list being non-empty
ext4: Handle unwritten extent properly with delayed allocation
Linus Torvalds [Fri, 22 Aug 2008 15:36:20 +0000 (08:36 -0700)]
Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nohz: fix wrong event handler after online an offlined cpu
Linus Torvalds [Fri, 22 Aug 2008 15:23:53 +0000 (08:23 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: work around MTRR mask setting, v2
x86: fix section mismatch warning - uv_cpu_init
x86: fix VMI for early params
x86: fix two modpost warnings in mm/init_64.c
x86: fix 1:1 mapping init on 64-bit (memory hotplug case)
x86: work around MTRR mask setting
x86: PAT Update validate_pat_support for intel CPUs
devmem, x86: PAT Change /dev/mem mmap with O_SYNC to use UC_MINUS
x86: PAT proper tracking of set_memory_uc and friends
x86: fix BUG: unable to handle kernel paging request (numaq_tsc_disable)
x86: export pv_lock_ops non-GPL
x86, mmiotrace: silence section mismatch warning - leave_uniprocessor
x86: use WARN() in arch/x86/kernel
x86: use WARN() in arch/x86/mm/ioremap.c
werror: fix pci calgary
x86: fix oprofile + hibernation badness
x86, SGI UV: hardcode the TLB flush interrupt system vector
x86: fix Xorg startup/shutdown slowdown with PAT
x86: fix "kernel won't boot on a Cyrix MediaGXm (Geode)"
x86 iommu: remove unneeded parenthesis
Linus Torvalds [Fri, 22 Aug 2008 15:22:33 +0000 (08:22 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] pata_it821x: fix warning
libata: Fix a large collection of DMA mode mismatches
ahci: sis controllers actually can do PMP
pata_via: clean up recent tf_load changes
libata: restore SControl on detach
libata: use ata_link_printk() when printing SError
libata: always do follow-up SRST if hardreset returned -EAGAIN
libata: fix EH action overwriting in ata_eh_reset()
sata_mv: add the Gen IIE flag to the SoC devices.
ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs
ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDs
sata_mv: don't issue two DMA commands concurrently
libata: implement no[hs]rst force params
Linus Torvalds [Fri, 22 Aug 2008 15:21:48 +0000 (08:21 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Fix deadlock on RTNL in ipoib_stop()
IB/ipath: Fix incorrect check for max physical address in TID
IB/ipath: Fix lost UD send work request
Herbert Xu [Fri, 22 Aug 2008 15:04:06 +0000 (01:04 +1000)]
crypto: authenc - Avoid using clobbered request pointer
Authenc works in two stages for encryption, it first encrypts and
then computes an ICV. The context memory of the request is used
by both operations. The problem is that when an asynchronous
encryption completes, we will compute the ICV and then reread the
context memory of the encryption to get the original request.
It just happens that we have a buffer of 16 bytes in front of the
request pointer, so ICVs of 16 bytes (such as SHA1) do not trigger
the bug. However, any attempt to uses a larger ICV instantly kills
the machine when the first asynchronous encryption is completed.
This patch fixes this by saving the request pointer before we start
the ICV computation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Takashi Iwai [Fri, 22 Aug 2008 13:24:22 +0000 (15:24 +0200)]
ALSA: hda - Fix call of alc888_coef_init()
Using init_hook to call alc888_coef_init() is problematic for configurations
that already set another init_hook. Better to put it in alc_init() as is
(although it looks a bit hackish).
Marcin Slusarz [Thu, 21 Aug 2008 18:49:05 +0000 (20:49 +0200)]
x86: fix section mismatch warning - uv_cpu_init
WARNING: vmlinux.o(.cpuinit.text+0x3cc4): Section mismatch in reference from the function uv_cpu_init() to the function .init.text:uv_system_init()
The function __cpuinit uv_cpu_init() references
a function __init uv_system_init().
If uv_system_init is only used by uv_cpu_init then
annotate uv_system_init with a matching annotation.
uv_system_init was ment to be called only once, so do it from codepath
(native_smp_prepare_cpus) which is called once, right before activation
of other cpus (smp_init).
Note: old code relied on uv_node_to_blade being initialized to 0,
but it'a not initialized from anywhere.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Acked-by: Jack Steiner <steiner@sgi.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jarek Poplawski [Fri, 22 Aug 2008 10:24:05 +0000 (03:24 -0700)]
pkt_sched: Fix qdisc list locking
Since some qdiscs call qdisc_tree_decrease_qlen() (so qdisc_lookup())
without rtnl_lock(), adding and deleting from a qdisc list needs
additional locking. This patch adds global spinlock qdisc_list_lock
and wrapper functions for modifying the list. It is considered as a
temporary solution until hfsc_dequeue(), netem_dequeue() and
tbf_dequeue() (or qdisc_tree_decrease_qlen()) are redone.
With feedback from Herbert Xu and David S. Miller.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Garzik [Fri, 22 Aug 2008 06:33:23 +0000 (02:33 -0400)]
[libata] pata_it821x: fix warning
Reported by Andrew Morton:
drivers/ata/pata_it821x.c: In function 'it821x_port_start':
drivers/ata/pata_it821x.c:609: warning: 'mtype' may be used uninitialized in
this function
Alan Cox [Fri, 1 Aug 2008 08:18:34 +0000 (09:18 +0100)]
libata: Fix a large collection of DMA mode mismatches
Dave Müller sent a diff for the pata_oldpiix that highlighted a problem
where a lot of the ATA drivers assume dma_mode == 0 means "no DMA" while
the core code uses 0xFF.
This turns out to have other consequences such as code doing >= XFER_UDMA_0
also catching 0xFF as UDMAlots. Fortunately it doesn't generally affect
set_dma_mode, although some drivers call back into their own set mode code
from other points.
Having been through the drivers I've added helpers for using_udma/using_mwdma
dma_enabled so that people don't open code ranges that may change (eg if UDMA8
appears somewhere)
Thanks to David for the initial bits
[and added fix for pata_oldpiix from and signed-off-by Dave Mueller
<dave.mueller@gmx.ch> -jg]
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Fri, 1 Aug 2008 03:51:43 +0000 (12:51 +0900)]
ahci: sis controllers actually can do PMP
SIS controllers were blacklisted for PMP as enabling it made device
detection fail whether the device was PMP or not - the natural
conclusion was the controller chokes on SRST w/ pmp==15. However, it
turned out that the controller just didn't like issuing SRST after
hardreset w/o clearing SError first. Interestingly, the SRST itself
succeeds but the following commands fail.
If SError is cleared between hardreset and SRST, which is the default
behavior now, everything works fine and SIS controllers work with PMPs
happily.
Remove PMP blacklisting for SIS AHCIs.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Piter PUNK <piterpunk@slackware.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Save SControl during probing and restore it on detach. This prevents
adjustments made by libata drivers to seep into the next driver which
gets attached (be it a libata one or not).
It's not clear whether SControl also needs to be restored on suspend.
The next system to have control (ACPI or kexec'd kernel) would
probably like to see the original SControl value but there's no
guarantee that a link is gonna keep working after SControl is adjusted
without a reset and adding a reset and modified recovery cycle soley
for this is an overkill. For now, do it only for detach.
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata: always do follow-up SRST if hardreset returned -EAGAIN
As an optimization, follow-up SRST used to be skipped if
classification wasn't requested even when hardreset requested it via
-EAGAIN. However, some hardresets can't wait for device readiness and
skipping SRST can cause timeout or other failures during revalidation.
Always perform follow-up SRST if hardreset returns -EAGAIN. This
makes reset paths more predictable and thus less error-prone.
While at it, move hardreset error checking such that it's done right
after hardreset is finished. This simplifies followup SRST condition
check a bit and makes the reset path easier to modify.
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata: fix EH action overwriting in ata_eh_reset()
ehc->i.action got accidentally overwritten to ATA_EH_HARD/SOFTRESET in
ata_eh_reset(). The original intention was to clear reset action
which wasn't selected. This can cause unexpected behavior when other
EH actions are scheduled together with reset. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Wed, 13 Aug 2008 11:24:16 +0000 (20:24 +0900)]
sata_mv: don't issue two DMA commands concurrently
sata_mv allowed issuing two DMA commands concurrently which the
hardware allows. Unfortunately, libata core layer isn't ready for
this yet and spews ugly warning message and malfunctions on this.
Don't allow concurrent DMA commands for now.
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jan Beulich [Thu, 21 Aug 2008 13:27:22 +0000 (14:27 +0100)]
x86: fix 1:1 mapping init on 64-bit (memory hotplug case)
While I don't have a hotplug capable system at hand, I think two issues need
fixing:
- pud_phys (in kernel_physical_ampping_init()) would remain uninitialized in
the after_bootmem case
- the locking done just around phys_pmd_{init,update}() would leave out pgd
updates, and it was needlessly covering code portions that do allocations
(perhaps using a more friendly gfp value in alloc_low_page() would then be
possible)
Signed-off-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yinghai Lu [Fri, 22 Aug 2008 03:24:24 +0000 (20:24 -0700)]
x86: work around MTRR mask setting
Joshua Hoblitt reported that only 3 GB of his 16 GB of RAM is
usable. Booting with mtrr_show showed us the BIOS-initialized
MTRR settings - which are all wrong.
So the root cause is that the BIOS has not set the mask correctly:
Linus Torvalds [Thu, 21 Aug 2008 23:31:08 +0000 (16:31 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5212/1: pxa: fix build error when CPU_PXA310 is not defined
[ARM] 5208/1: fsg-setup.c fixes
[ARM] fix impd1.c build warning
[ARM] e400 config use MFP
[ARM] e740 config use MFP
[ARM] Fix eseries IRQ limit
[ARM] clocklib: Update users of aliases to new API
[ARM] clocklib: Allow dynamic alias creation
[ARM] eseries: whitespace fixes and cleanup
Greg KH [Thu, 21 Aug 2008 20:47:58 +0000 (13:47 -0700)]
PCI: fix reference leak in pci_get_dev_by_id()
Alex Chiang and Matthew Wilcox pointed out that pci_get_dev_by_id() does
not properly decrement the reference on the from pointer if it is
present, like the documentation for the function states it will.
It fixes a pretty bad leak in the hotplug core (we were leaking an
entire struct pci_dev for each function of each offlined card, the first
time around; subsequent onlines/offlines were ok).
Cc: Matthew Wilcox <matthew@wil.cx> Cc: stable <stable@kernel.org> Tested-by: Alex Chiang <achiang@hp.com> Acked-by: Alex Chiang <achiang@hp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Alex Chiang [Thu, 21 Aug 2008 21:13:47 +0000 (15:13 -0600)]
PCI: shpchp: Rename duplicate slot name N as N-1, N-2, N-M...
Commit ef0ff95f136f0f2d035667af5d18b824609de320 (shpchp: fix slot name)
introduces the shpchp_slot_with_bus module parameter, which was intended
to help work around broken firmware that assigns the same name to multiple
slots.
Commit b3bd307c628af2f0a581c42d5d7e4bcdbbf64b6a (shpchp: add message about
shpchp_slot_with_bus option) tells the user to use the above parameter
in the event of a name collision.
This approach is sub-optimal because it requires too much work from
the user.
Instead, let's rename the slot on behalf of the user. If firmware
assigns the name N to multiple slots, then:
The first registered slot is assigned N
The second registered slot is assigned N-1
The third registered slot is assigned N-2
The Mth registered slot becomes N-M
In the event we overflow the slot->name parameter, we report an
error to the user.
This is a temporary fix until the entire PCI core can be reworked
such that individual drivers no longer have to manage their own
slot names.
Alex Chiang [Thu, 21 Aug 2008 21:13:29 +0000 (15:13 -0600)]
PCI: pciehp: Rename duplicate slot name N as N-1, N-2, N-M...
Commit 3800345f723fd130d50434d4717b99d4a9f383c8 (pciehp: fix slot name)
introduces the pciehp_slot_with_bus module parameter, which was intended
to help work around broken firmware that assigns the same name to multiple
slots.
Commit 9e4f2e8d4ddb04ad16a3828cd9a369a5a5287009 (pciehp: add message about
pciehp_slot_with_bus option) tells the user to use the above parameter
in the event of a name collision.
This approach is sub-optimal because it requires too much work from
the user.
Instead, let's rename the slot on behalf of the user. If firmware
assigns the name N to multiple slots, then:
The first registered slot is assigned N
The second registered slot is assigned N-1
The third registered slot is assigned N-2
The Mth registered slot becomes N-M
In the event we overflow the slot->name parameter, we report an
error to the user.
This is a temporary fix until the entire PCI core can be reworked
such that individual drivers no longer have to manage their own
slot names.
projects / karo-tx-linux.git / log