Merge tag 'irqchip-fixes-4.0-2' of git://git.infradead.org/users/jcooper/linux
Pull irqchip fixes from Jason Cooper:
"This is the second round of fixes for irqchip. It contains some fixes
found while the arm64 guys were writing the kvm gicv3 its emulation.
GICv3 ITS:
- Small batch of fixes discovered while writing the kvm ITS emulation"
* tag 'irqchip-fixes-4.0-2' of git://git.infradead.org/users/jcooper/linux:
irqchip: gicv3-its: Use non-cacheable accesses when no shareability
irqchip: gicv3-its: Fix PROP/PEND and BASE/CBASE confusion
irqchip: gicv3-its: Fix device ID encoding
irqchip: gicv3-its: Fix encoding of collection's target redistributor
Merge tag 'stable/for-linus-4.0-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen regression fixes from David Vrabel:
"Fix two regressions in the balloon driver's use of memory hotplug when
used in a PV guest"
* tag 'stable/for-linus-4.0-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: before adding hotplugged memory, set frames to invalid
x86/xen: prepare p2m list for memory hotplug
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma fix from Roland Dreier:
"Fix for exploitable integer overflow in uverbs interface"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/uverbs: Prevent integer overflow in ib_umem_get address arithmetic
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"This time we have addition of caps for jz4740 which fixes intentional
warning at boot. Then we have memory leak issues in drivers using
virt-dma by Peter on few drive"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: moxart-dma: Fix memory leak when stopping a running transfer
dmaengine: bcm2835-dma: Fix memory leak when stopping a running transfer
dmaengine: omap-dma: Fix memory leak when terminating running transfer
dmaengine: edma: fix memory leak when terminating running transfers
dmaengine: jz4740: Define capabilities
1) Fix use-after-free with mac80211 RX A-MPDU reorder timer, from
Johannes Berg.
2) iwlwifi leaks memory every module load/unload cycles, fix from Larry
Finger.
3) Need to use for_each_netdev_safe() in rtnl_group_changelink()
otherwise we can crash, from WANG Cong.
4) mlx4 driver does register_netdev() too early in the probe sequence,
from Ido Shamay.
5) Don't allow router discovery hop limit to decrease the interface's
hop limit, from D.S. Ljungmark.
6) tx_packets and tx_bytes improperly accounted for certain classes of
USB network devices, fix from Ben Hutchings.
7) ip{6}mr_rules_init() mistakenly use plain kfree to release the ipmr
tables in the error path, they must instead use ip{6}mr_free_table().
Fix from WANG Cong.
8) cxgb4 doesn't properly quiesce all RX activity before unregistering
the netdevice. Fix from Hariprasad Shenai.
9) Fix hash corruptions in ipvlan driver, from Jiri Benc.
10) nla_memcpy(), like a real memcpy, should fully initialize the
destination buffer, even if the source attribute is smaller. Fix
from Jiri Benc.
11) Fix wrong error code returned from iucv_sock_sendmsg(). We should
use whatever sock_alloc_send_skb() put into 'err'. From Eugene
Crosser.
12) Fix slab object leak on module unload in TIPC, from Ying Xue.
13) Need a READ_ONCE() when reading the cached RX socket route in
tcp_v{4,6}_early_demux(). From Michal Kubecek.
14) Still too many problems with TPC support in the ath9k driver, so
disable it for now. From Felix Fietkau.
15) When in AP mode the rtlwifi driver can leak DMA mappings, fix from
Larry Finger.
16) Missing kzalloc() failure check in gs_usb CAN driver, from Colin Ian
King.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
cxgb4: Fix to dump devlog, even if FW is crashed
cxgb4: Firmware macro changes for fw verison 1.13.32.0
bnx2x: Fix kdump when iommu=on
bnx2x: Fix kdump on 4-port device
mac80211: fix RX A-MPDU session reorder timer deletion
MAINTAINERS: Update Intel Wired Ethernet Driver info
tipc: fix a slab object leak
net/usb/r8152: add device id for Lenovo TP USB 3.0 Ethernet
af_iucv: fix AF_IUCV sendmsg() errno
openvswitch: Return vport module ref before destruction
netlink: pad nla_memcpy dest buffer with zeroes
bonding: Bonding Overriding Configuration logic restored.
ipvlan: fix check for IP addresses in control path
ipvlan: do not use rcu operations for address list
ipvlan: protect against concurrent link removal
ipvlan: fix addr hash list corruption
net: fec: setup right value for mdio hold time
net: tcp6: fix double call of tcp_v6_fill_cb()
cxgb4vf: Fix sparse warnings
netns: don't clear nsid too early on removal
...
Shachar Raindel [Wed, 18 Mar 2015 17:39:08 +0000 (17:39 +0000)]
IB/uverbs: Prevent integer overflow in ib_umem_get address arithmetic
Properly verify that the resulting page aligned end address is larger
than both the start address and the length of the memory area requested.
Both the start and length arguments for ib_umem_get are controlled by
the user. A misbehaving user can provide values which will cause an
integer overflow when calculating the page aligned end address.
This overflow can cause also miscalculation of the number of pages
mapped, and additional logic issues.
Addresses: CVE-2014-8159 Cc: <stable@vger.kernel.org> Signed-off-by: Shachar Raindel <raindel@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
David S. Miller [Wed, 1 Apr 2015 18:47:21 +0000 (14:47 -0400)]
Merge branch 'cxgb4-net'
Hariprasad Shenai says:
====================
cxgb4 FW macro changes for new FW
Fix to dump device log even in the case of firmware crash. Also
incorporates changes for new FW.
This patch series has been created against net tree and includes patches on
cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new Common Code routines to retrieve Firmware Device Log
parameters from PCIE_FW_PF[7]. The firmware initializes its Device Log very
early on and stores the parameters for its location/size in that register.
Using the parameters from the register allows us to access the Firmware
Device Log even when the firmware crashes very early on or we're not
attached to the firmware
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Apr 2015 18:19:22 +0000 (14:19 -0400)]
Merge tag 'mac80211-for-davem-2015-04-01' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
This contains just a single fix for a crash I happened to randomly
run into today during testing. It's clearly been around for a while,
but is pretty hard to trigger, even when I tried explicitly (and
modified the code to make it more likely) it rarely did.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'lazytime_fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull lazytime fixes from Ted Ts'o:
"This fixes a problem in the lazy time patches, which can cause
frequently updated inods to never have their timestamps updated.
These changes guarantee that no timestamp on disk will be stale by
more than 24 hours"
* tag 'lazytime_fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
fs: add dirtytime_expire_seconds sysctl
fs: make sure the timestamps for lazytime inodes eventually get written
Merge branch 'for-4.0' of git://linux-nfs.org/~bfields/linux
Pull nfsd fixes from Bruce Fields:
"Two main issues:
- We found that turning on pNFS by default (when it's configured at
build time) was too aggressive, so we want to switch the default
before the 4.0 release.
- Recent client changes to increase open parallelism uncovered a
serious bug lurking in the server's open code.
Also fix a krb5/selinux regression.
The rest is mainly smaller pNFS fixes"
* 'for-4.0' of git://linux-nfs.org/~bfields/linux:
sunrpc: make debugfs file creation failure non-fatal
nfsd: require an explicit option to enable pNFS
NFSD: Fix bad update of layout in nfsd4_return_file_layout
NFSD: Take care the return value from nfsd4_encode_stateid
NFSD: Printk blocklayout length and offset as format 0x%llx
nfsd: return correct lockowner when there is a race on hash insert
nfsd: return correct openowner when there is a race to put one in the hash
NFSD: Put exports after nfsd4_layout_verify fail
NFSD: Error out when register_shrinker() fail
NFSD: Take care the return value from nfsd4_decode_stateid
NFSD: Check layout type when returning client layouts
NFSD: restore trace event lost in mismerge
David S. Miller [Wed, 1 Apr 2015 16:30:39 +0000 (12:30 -0400)]
Merge branch 'bnx2'
Yuval Mintz says:
====================
bnx2x: kdump related fixes
This patch series aims to fix bnx2x driver issues when loading in kdump kernel.
Both issues fixed here would be fatal to the device, requiring full reset of
the system in order to recover, preventing the device from serving its purpose
in the kdump environment.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When IOMM-vtd is active, once main kernel crashes unfinished DMAE transactions
will be blocked, putting the HW in an error state which will cause further
transactions to timeout.
Current employed logic uses wrong macros, causing the first function to be the
only function that cleanups that error state during its probe/load.
This patch allows all the functions to successfully re-load in kdump kernel.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When running in a kdump kernel, it's very likely that due to sync. loss with
management firmware the first PCI function to probe and reach the previous
unload flow would decide it can reset the chip and continue onward. While doing
so, it will only close its own Rx port.
On a 4-port device where 2nd port on engine is a 1g-port, the 2nd port would
allow ingress traffic after the chip is reset [assuming it was active on the
first kernel]. This would later cause a HW attention.
This changes driver flow to close both ports' 1g capabilities during the
previous driver unload flow prior to the chip reset.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There's an issue with the way the RX A-MPDU reorder timer is
deleted that can cause a kernel crash like this:
* tid_rx is removed - call_rcu(ieee80211_free_tid_rx)
* station is destroyed
* reorder timer fires before ieee80211_free_tid_rx() runs,
accessing the station, thus potentially crashing due to
the use-after-free
The station deletion is protected by synchronize_net(), but
that isn't enough -- ieee80211_free_tid_rx() need not have
run when that returns (it deletes the timer.) We could use
rcu_barrier() instead of synchronize_net(), but that's much
more expensive.
Instead, to fix this, add a field tracking that the session
is being deleted. In this case, the only re-arming of the
timer happens with the reorder spinlock held, so make that
code not rearm it if the session is being deleted and also
delete the timer after setting that field. This ensures the
timer cannot fire after ___ieee80211_stop_rx_ba_session()
returns, which fixes the problem.
Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jeff Kirsher [Thu, 26 Mar 2015 00:01:03 +0000 (17:01 -0700)]
MAINTAINERS: Update Intel Wired Ethernet Driver info
Update the git tree info with a recent change in tree names. Also
add our new mailing list created solely for Linux kernel patches
and kernel development, as well as the new patchwork project for
tracking patches. Lastly update the list of "reviewers" since a
couple of developers have moved on to different projects.
Made an update to the section header so that it is more manageable
going forward as we add new drivers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is because the listening socket of TIPC topology server is not
closed before TIPC proto handler is unregistered with proto_unregister().
However, as the socket is closed in tipc_exit_net() which is called by
unregister_pernet_subsys() during unregistering TIPC namespace operation,
the warning can be eliminated if calling unregister_pernet_subsys() is
moved before calling proto_unregister().
Fixes: e05b31f4bf89 ("tipc: make tipc socket support net namespace") Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Signed-off-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Stancek [Tue, 31 Mar 2015 16:11:46 +0000 (18:11 +0200)]
powerpc: fix memory corruption by pnv_alloc_idle_core_states
Space allocated for paca is based off nr_cpu_ids,
but pnv_alloc_idle_core_states() iterates paca with
cpu_nr_cores()*threads_per_core, which is using NR_CPUS.
This causes pnv_alloc_idle_core_states() to write over memory,
which is outside of paca array and may later lead to various panics.
Fixes: 7cba160ad789 (powernv/cpuidle: Redesign idle states management) Signed-off-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Eugene Crosser [Mon, 30 Mar 2015 13:40:42 +0000 (15:40 +0200)]
af_iucv: fix AF_IUCV sendmsg() errno
When sending over AF_IUCV socket, errno was incorrectly set to
ENOMEM even when other values where appropriate, notably EAGAIN.
With this patch, error indicator returned by sock_alloc_send_skb()
is passed to the caller, rather than being overwritten with ENOMEM.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf [Mon, 30 Mar 2015 11:57:41 +0000 (13:57 +0200)]
openvswitch: Return vport module ref before destruction
Return module reference before invoking the respective vport
->destroy() function. This is needed as ovs_vport_del() is not
invoked inside an RCU read side critical section so the kfree
can occur immediately before returning to ovs_vport_del().
Returning the module reference before ->destroy() is safe because
the module unregistration is blocked on ovs_lock which we hold
while destroying the datapath.
Fixes: 62b9c8d0372d ("ovs: Turn vports with dependencies into separate modules") Reported-by: Pravin Shelar <pshelar@nicira.com> Signed-off-by: Thomas Graf <tgraf@suug.ch> Acked-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Layton [Tue, 31 Mar 2015 16:03:28 +0000 (12:03 -0400)]
sunrpc: make debugfs file creation failure non-fatal
We currently have a problem that SELinux policy is being enforced when
creating debugfs files. If a debugfs file is created as a side effect of
doing some syscall, then that creation can fail if the SELinux policy
for that process prevents it.
This seems wrong. We don't do that for files under /proc, for instance,
so Bruce has proposed a patch to fix that.
While discussing that patch however, Greg K.H. stated:
"No kernel code should care / fail if a debugfs function fails, so
please fix up the sunrpc code first."
This patch converts all of the sunrpc debugfs setup code to be void
return functins, and the callers to not look for errors from those
functions.
This should allow rpc_clnt and rpc_xprt creation to work, even if the
kernel fails to create debugfs files for some reason.
Symptoms were failing krb5 mounts on systems using gss-proxy and
selinux.
Fixes: 388f0c776781 "sunrpc: add a debugfs rpc_xprt directory..." Cc: stable@vger.kernel.org Signed-off-by: Jeff Layton <jeff.layton@primarydata.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Jiri Benc [Sun, 29 Mar 2015 14:05:28 +0000 (16:05 +0200)]
netlink: pad nla_memcpy dest buffer with zeroes
This is especially important in cases where the kernel allocs a new
structure and expects a field to be set from a netlink attribute. If such
attribute is shorter than expected, the rest of the field is left containing
previous data. When such field is read back by the user space, kernel memory
content is leaked.
Signed-off-by: Jiri Benc <jbenc@redhat.com> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit 3900f29021f0bc7fe9815aa32f1a993b7dfdd402 ("bonding: slight
optimizztion for bond_slave_override()") the override logic was to send packets
with non-zero queue_id through the slave with corresponding queue_id, under two
conditions only - if the slave can transmit and it's up.
The above mentioned commit changed this logic by introducing an additional
condition - whether the bond is active (indirectly, using the slave_can_tx and
later - bond_is_active_slave), that prevents the user from implementing more
complex policies according to the Documentation/networking/bonding.txt.
Signed-off-by: Anton Nayshtut <anton@swortex.com> Signed-off-by: Alexey Bogoslavsky <alexey@swortex.com> Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Sat, 28 Mar 2015 18:13:25 +0000 (19:13 +0100)]
ipvlan: fix check for IP addresses in control path
When an ipvlan interface is down, its addresses are not on the hash list.
Fix checks for existence of addresses not to depend on the hash list, walk
through all interface addresses instead.
Signed-off-by: Jiri Benc <jbenc@redhat.com> Acked-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Sat, 28 Mar 2015 18:13:22 +0000 (19:13 +0100)]
ipvlan: fix addr hash list corruption
When ipvlan interface with IP addresses attached is brought down and then
deleted, the assigned addresses are deleted twice from the address hash
list, first on the interface down and second on the link deletion.
Similarly, when an address is added while the interface is down, it is added
second time once the interface is brought up.
When the interface is down, the addresses should be kept off the hash list
for performance reasons. Ensure this is true, which also fixes the double add
problem. To fix the double free, check whether the address is hashed before
removing it.
Reported-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 30 Mar 2015 18:08:37 +0000 (11:08 -0700)]
Merge branch 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Nothing exciting. Two patches to update queued trim blacklist"
* 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: Blacklist queued TRIM on Samsung SSD 850 Pro
libata: Update Crucial/Micron blacklist
Peter Ujfalusi [Fri, 27 Mar 2015 11:35:52 +0000 (13:35 +0200)]
dmaengine: omap-dma: Fix memory leak when terminating running transfer
In omap_dma_start_desc the vdesc->node is removed from the virt-dma
framework managed lists (to be precise from the desc_issued list).
If a terminate_all comes before the transfer finishes the omap_desc will
not be freed up because it is not in any of the lists and we stopped the
DMA channel so the transfer will not going to complete.
There is no special sequence for leaking memory when using cyclic (audio)
transfer: with every start and stop of a cyclic transfer the driver leaks
struct omap_desc worth of memory.
Free up the allocated memory directly in omap_dma_terminate_all() since the
framework will not going to do that for us.
Petr Kulhavy [Fri, 27 Mar 2015 11:35:51 +0000 (13:35 +0200)]
dmaengine: edma: fix memory leak when terminating running transfers
If edma_terminate_all() was called while a transfer was running (i.e. after
edma_execute() but before edma_callback()) the echan->edesc was not freed.
This was due to the fact that a running transfer is on none of the
vchan lists: desc_submitted, desc_issued, desc_completed (edma_execute()
removes it from the desc_issued list), so the vchan_dma_desc_free_list()
called at the end of edma_terminate_all() didn't find it and didn't free it.
This bug was found on an AM1808 based hardware (very similar to da850evm,
however using the second MMC/SD controller), where intense operations on the SD
card wasted the device 128MB RAM within a couple of days.
Peter Ujfalusi:
The issue is even more severe since it affects cyclic (audio) transfers as
well. In this case starting/stopping audio will results memory leak.
Signed-off-by: Petr Kulhavy <petr@barix.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> CC: <stable@vger.kernel.org> CC: <linux-omap@vger.kernel.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Linus Torvalds [Mon, 30 Mar 2015 16:14:41 +0000 (09:14 -0700)]
Merge tag 'gpio-v4.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull late GPIO fixes from Linus Walleij:
"Here are the (hopefully) last GPIO fixes for v4.0. Nothing
controversial whatsoever, just fixes:
- syscon GPIO fix for Keystone DSP GPIOs
- pin number translation fix for ACPI GPIO
- a smallish compiler warning fix on the mpc8xxx driver"
* tag 'gpio-v4.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: syscon: reduce message level when direction reg offset not in dt
gpiolib: translate pin number in GPIO ACPI callbacks
gpio: mpc8xxx: remove __initdata annotation for mpc8xxx_gpio_ids[]
Linus Torvalds [Sun, 29 Mar 2015 22:09:31 +0000 (15:09 -0700)]
Merge tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"The latest and greatest fixes for ARM platform code. Worth pointing
out are:
- Lines-wise, largest is a PXA fix for dealing with interrupts on DT
that was quite broken. It's still newish code so while we could
have held this off, it seemed appropriate to include now
- Some GPIO fixes for OMAP platforms added a few lines. This was
also fixes for code recently added (this release).
- Small OMAP timer fix to behave better with partially upstreamed
platforms, which is quite welcome.
- Allwinner fixes about operating point control, reducing
overclocking in some cases for better stability.
plus a handful of other smaller fixes across the map"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: juno: Fix misleading name of UART reference clock
ARM: dts: sunxi: Remove overclocked/overvoltaged OPP
ARM: dts: sun4i: a10-lime: Override and remove 1008MHz OPP setting
ARM: socfpga: dts: fix spi1 interrupt
ARM: dts: Fix gpio interrupts for dm816x
ARM: dts: dra7: remove ti,hwmod property from pcie phy
ARM: OMAP: dmtimer: disable pm runtime on remove
ARM: OMAP: dmtimer: check for pm_runtime_get_sync() failure
ARM: OMAP2+: Fix socbus family info for AM33xx devices
ARM: dts: omap3: Add missing dmas for crypto
ARM: dts: rockchip: disable gmac by default in rk3288.dtsi
MAINTAINERS: add rockchip regexp to the ARM/Rockchip entry
ARM: pxa: fix pxa interrupts handling in DT
ARM: pxa: Fix typo in zeus.c
ARM: sunxi: Have ARCH_SUNXI select RESET_CONTROLLER for clock driver usage
Olof Johansson [Sun, 29 Mar 2015 21:00:53 +0000 (14:00 -0700)]
Merge tag 'sunxi-fixes-for-4.0' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.0
There's a few fixes to merge for 4.0, one to add a select in the machine
Kconfig option to fix a potential build failure, and two fixing cpufreq related
issues.
* tag 'sunxi-fixes-for-4.0' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sunxi: Remove overclocked/overvoltaged OPP
ARM: dts: sun4i: a10-lime: Override and remove 1008MHz OPP setting
ARM: sunxi: Have ARCH_SUNXI select RESET_CONTROLLER for clock driver usage
Olof Johansson [Sun, 29 Mar 2015 20:58:54 +0000 (13:58 -0700)]
Merge tag 'fixes-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for the -rc cycle:
- Fix a device tree based booting vs legacy booting regression for
omap3 crypto hardware by adding the missing DMA channels.
- Fix /sys/bus/soc/devices/soc0/family for am33xx devices.
- Fix two timer issues that can cause hangs if the timer related
hwmod data is missing like it often initially is for new SoCs.
- Remove pcie hwmods entry from dts as that causes runtime PM to
fail for the PHYs.
- A paper bag type dts configuration fix for dm816x GPIO
interrupts that I just noticed. This is most of the changes
diffstat wise, but as it's a basic feature for connecting
devices and things work otherwise, it should be fixed.
* tag 'fixes-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix gpio interrupts for dm816x
ARM: dts: dra7: remove ti,hwmod property from pcie phy
ARM: OMAP: dmtimer: disable pm runtime on remove
ARM: OMAP: dmtimer: check for pm_runtime_get_sync() failure
ARM: OMAP2+: Fix socbus family info for AM33xx devices
ARM: dts: omap3: Add missing dmas for crypto
Olof Johansson [Sun, 29 Mar 2015 20:47:21 +0000 (13:47 -0700)]
Merge tag 'fixes-for-v4.0-rc5' of https://github.com/rjarzmik/linux into fixes
arm: pxa: fixes for v4.0-rc5
There are only 2 fixes, one for the zeus board about the regulator changes,
where a typo prevented the zeus board from having a working can regulator,
and one regression triggered by the interrupts IRQ shift of 16 affecting all
boards.
* tag 'fixes-for-v4.0-rc5' of https://github.com/rjarzmik/linux:
ARM: pxa: fix pxa interrupts handling in DT
ARM: pxa: Fix typo in zeus.c
Uwe Kleine-König [Fri, 27 Mar 2015 10:08:32 +0000 (11:08 +0100)]
net: fec: setup right value for mdio hold time
The FEC modules used on i.MX28 and newer have a register to tune the MDIO
output hold time that should be at least 10 ns. Up to now this value was not
explicitly set and so resulted in less hold time if the fec clock was
faster than 100 MHz.
This was noticed on an i.MX28 machine that uses an input clock of ~150
Mhz which resulted in unreliable communication with a Marvell switch.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Kodanev [Fri, 27 Mar 2015 09:24:22 +0000 (12:24 +0300)]
net: tcp6: fix double call of tcp_v6_fill_cb()
tcp_v6_fill_cb() will be called twice if socket's state changes from
TCP_TIME_WAIT to TCP_LISTEN. That can result in control buffer data
corruption because in the second tcp_v6_fill_cb() call it's not copying
IP6CB(skb) anymore, but 'seq', 'end_seq', etc., so we can get weird and
unpredictable results. Performance loss of up to 1200% has been observed
in LTP/vxlan03 test.
This can be fixed by copying inet6_skb_parm to the beginning of 'cb'
only if xfrm6_policy_check() and tcp_v6_fill_cb() are going to be
called again.
Fixes: 2dc49d1680b53 ("tcp6: don't move IP6CB before xfrm6_policy_check()") Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes sparse warnings introduced in commit e85c9a7abfa407ed ("cxgb4/cxgb4vf: Add
code to calculate T5 BAR2 Offsets for SGE Queue Registers") and df64e4d38c904dd3 ("cxgb4/cxgb4vf: Use new interfaces to calculate BAR2 SGE Queue
Register addresses") and few old ones
sparse warnings:
>> drivers/net/ethernet/chelsio/cxgb4vf/sge.c:1006:48: sparse: cast removes
>> address space of expression
>> drivers/net/ethernet/chelsio/cxgb4vf/sge.c:1006:48: sparse: incorrect type in
>> initializer (different address space)
>> drivers/net/ethernet/chelsio/cxgb4vf/sge.c:1020:40: sparse: incorrect type in
>> argument 1 (different base types)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 26 Mar 2015 16:56:38 +0000 (17:56 +0100)]
netns: don't clear nsid too early on removal
With the current code, ids are removed too early.
Suppose you have an ipip interface that stands in the netns foo and its link
part in the netns bar (so the netns bar has an nsid into the netns foo).
Now, you remove the netns bar:
- the bar nsid into the netns foo is removed
- the netns exit method of ipip is called, thus our ipip iface is removed:
=> a netlink message is sent in the netns foo to advertise this deletion
=> this netlink message requests an nsid for bar, thus a new nsid is
allocated for bar and never removed.
We must remove nsids when we are sure that nobody will refer to netns currently
cleaned.
Fixes: 0c7aecd4bde4 ("netns: add rtnl cmd to add and get peer netns ids") Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Zyngier [Fri, 27 Mar 2015 14:15:05 +0000 (14:15 +0000)]
irqchip: gicv3-its: Use non-cacheable accesses when no shareability
If the ITS or the redistributors report their shareability as zero,
then it is important to make sure they will no generate any cacheable
traffic, as this is unlikely to produce the expected result.
Andre Przywara [Fri, 27 Mar 2015 14:15:03 +0000 (14:15 +0000)]
irqchip: gicv3-its: Fix device ID encoding
When building ITS commands which have the device ID in it, we
should mask off the whole upper 32 bits of the first command word
before inserting the new value in there.
Marc Zyngier [Fri, 27 Mar 2015 14:15:02 +0000 (14:15 +0000)]
irqchip: gicv3-its: Fix encoding of collection's target redistributor
With a monolithic GICv3, redistributors are addressed using a linear
number, while a distributed implementation uses physical addresses.
When encoding a target address into a command, we strip the lower
16 bits, as redistributors are always 64kB aligned. This works
perfectly well with a distributed implementation, but has the
silly effect of always encoding target 0 in the monolithic case
(unless you have more than 64k CPUs, of course).
The obvious fix is to shift the linear target number by 16 when
computing the target address, so that we don't loose any precious
bit.
David S. Miller [Sun, 29 Mar 2015 19:24:46 +0000 (12:24 -0700)]
Merge branch 'cxgb4'
Hariprasad Shenai says:
====================
cxgb4: Fixes ingress queue mapping and other fixes
The below series fixes ingress queue mapping by allocating them dynamically to
prevent stack overflow. Disable napi and interrupts before unregistering netdev
to avoid crash while unloading driver when traffic is flowing.
The patches series is created against 'net' tree.
And includes patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4: Allocate dynamic mem. for egress and ingress queue maps
QIDs (egress/ingress) from firmware in FW_*_CMD.alloc command
can be anywhere in the range from EQ(IQFLINT)_START to EQ(IQFLINT)_END.
For eg, in the first load eqid can be from 100 to 300.
In the next load it can be from 301 to 500 (assume eq_start is 100 and eq_end is
1000).
The driver was assuming them to always start from EQ(IQFLINT)_START till
MAX_EGRQ(INGQ). This was causing stack overflow and subsequent crash.
Fixed it by dynamically allocating memory (of qsize (x_END - x_START + 1)) for
these structures.
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 25 Mar 2015 20:41:33 +0000 (21:41 +0100)]
usbnet: Fix tx_bytes statistic running backward in cdc_ncm
cdc_ncm disagrees with usbnet about how much framing overhead should
be counted in the tx_bytes statistics, and tries 'fix' this by
decrementing tx_bytes on the transmit path. But statistics must never
be decremented except due to roll-over; this will thoroughly confuse
user-space. Also, tx_bytes is only incremented by usbnet in the
completion path.
Fix this by requiring drivers that set FLAG_MULTI_FRAME to set a
tx_bytes delta along with the tx_packets count.
Ben Hutchings [Thu, 26 Feb 2015 19:34:37 +0000 (19:34 +0000)]
usbnet: Fix tx_packets stat for FLAG_MULTI_FRAME drivers
Currently the usbnet core does not update the tx_packets statistic for
drivers with FLAG_MULTI_PACKET and there is no hook in the TX
completion path where they could do this.
cdc_ncm and dependent drivers are bumping tx_packets stat on the
transmit path while asix and sr9800 aren't updating it at all.
Add a packet count in struct skb_data so these drivers can fill it
in, initialise it to 1 for other drivers, and add the packet count
to the tx_packets statistic on completion.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Tested-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 28 Mar 2015 18:25:04 +0000 (11:25 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"Fix x86 syscall exit code bug that resulted in spurious non-execution
of TIF-driven user-return worklets, causing big trouble for things
like KVM that rely on user notifiers for correctness of their vcpu
model, causing crashes like double faults"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm/entry: Check for syscall exit work with IRQs disabled
Linus Torvalds [Sat, 28 Mar 2015 17:58:53 +0000 (10:58 -0700)]
Merge branch 'parisc-4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parsic fixes from Helge Deller:
"One patch from Mikulas fixes a bug on parisc by artifically
incrementing the counter in pmd_free when the kernel tries to free
the preallocated pmd.
Other than that we now prevent that syscalls gets added without
incrementing __NR_Linux_syscalls and fix the initial pmd setup code
if a default page size greater than 4k has been selected"
* 'parisc-4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix pmd code to depend on PT_NLEVELS value, not on CONFIG_64BIT
parisc: mm: don't count preallocated pmds
parisc: Add compile-time check when adding new syscalls
Linus Torvalds [Sat, 28 Mar 2015 17:47:27 +0000 (09:47 -0800)]
Merge tag 'arc-4.0-fixes-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"We found some issues with signal handling taking down the system. I
know its late, but these are important and all marked for stable.
ARC signal handling related fixes uncovered during recent testing of
NPTL tools"
* tag 'arc-4.0-fixes-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: signal handling robustify
ARC: SA_SIGINFO ucontext regs off-by-one
Linus Torvalds [Fri, 27 Mar 2015 21:38:02 +0000 (14:38 -0700)]
Merge tag 'sound-4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Three trivial oneliner fixes for HD-audio.
Two are device-specific quirks while one is a generic fix for recent
Realtek codecs"
* tag 'sound-4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add one more node in the EAPD supporting candidate list
ALSA: hda_intel: apply the Seperate stream_tag for Sunrise Point
ALSA: hda - Add dock support for Thinkpad T450s (17aa:5036)
libata: Blacklist queued TRIM on Samsung SSD 850 Pro
Blacklist queued TRIM on this drive for now.
Reported-by: Stefan Keller <linux-list@zahlenfresser.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> CC: stable@vger.kernel.org Signed-off-by: Tejun Heo <tj@kernel.org>
Micron has released an updated firmware (MU02) for M510/M550/MX100
drives to fix the issues with queued TRIM. Queued TRIM remains broken on
M500 but is working fine on later drives such as M600 and MX200.
gpio: syscon: reduce message level when direction reg offset not in dt
Now GPIO syscon driver produces bunch of warnings during the
boot of Kesytone 2 SoCs:
gpio-syscon soc:keystone_dsp_gpio@02620240: can't read the dir register offset!
gpio-syscon soc:keystone_dsp_gpio@2620244: can't read the dir register offset!
This message unintentionally was added using dev_err(), but its
actual log level is debug, because third cell of "ti,syscon-dev" is
optional.
Hence change it to dev_dbg() as it should be.
This patch fixes commit: 5a3e3f8 ("gpio: syscon: retriave syscon node and regs offsets from dt")
Reported-by: Russell King <linux@arm.linux.org.uk> Tested-by: Murali Karicheri <m-karicheri2@ti.com> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
James Hogan [Fri, 20 Feb 2015 23:45:45 +0000 (23:45 +0000)]
watchdog: imgpdc: Fix default heartbeat
The IMG PDC watchdog driver heartbeat module parameter has no default so
it is initialised to zero. This results in the following warning during
probe:
imgpdc-wdt 2006000.wdt: Initial timeout out of range! setting max timeout
The module parameter description implies that the default value should
be PDC_WDT_DEF_TIMEOUT, which isn't yet used, so initialise it to that.
Also tweak the heartbeat module parameter description for consistency.
The IMG PDC watchdog probe function calls pdc_wdt_stop() prior to
watchdog_set_drvdata(), causing a NULL pointer dereference when
pdc_wdt_stop() retrieves the struct pdc_wdt_dev pointer using
watchdog_get_drvdata() and reads the register base address through it.
Fix by moving the watchdog_set_drvdata() call earlier, to where various
other pdc_wdt->wdt_dev fields are initialised.
Linus Torvalds [Thu, 26 Mar 2015 22:04:05 +0000 (15:04 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm refcounting fixes from Dave Airlie:
"Here is the complete set of i915 bug/warn/refcounting fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Fixup legacy plane->crtc link for initial fb config
drm/i915: Fix atomic state when reusing the firmware fb
drm/i915: Keep ring->active_list and ring->requests_list consistent
drm/i915: Don't try to reference the fb in get_initial_plane_config()
drm: Fixup racy refcounting in plane_force_disable
Linus Torvalds [Thu, 26 Mar 2015 21:53:47 +0000 (14:53 -0700)]
Merge tag 'dm-4.0-fix-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix DM core device cleanup regression -- due to a latent race that was
exposed by the bdi changes that were introduced during the 4.0 merge"
* tag 'dm-4.0-fix-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix add_disk() NULL pointer due to race with free_dev()
Linus Torvalds [Thu, 26 Mar 2015 21:43:42 +0000 (14:43 -0700)]
Merge tag 'linux-kselftest-4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fix from Shuah Khan.
* tag 'linux-kselftest-4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: Fix build failures when invoked from kselftest target
Dave Airlie [Thu, 26 Mar 2015 21:39:45 +0000 (07:39 +1000)]
Merge tag 'drm-intel-fixes-2015-03-26' of git://anongit.freedesktop.org/drm-intel into drm-fixes
This should cover the final warnings in -rc5 with two more backports
from our development branch (drm-intel-next-queued). They're the ones
from Daniel and Damien, with references to the reports.
This is on top of drm-fixes because of the dependency on the two earlier
fixes not yet in Linus' tree.
There's an additional regression fix from Chris.
* tag 'drm-intel-fixes-2015-03-26' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fixup legacy plane->crtc link for initial fb config
drm/i915: Fix atomic state when reusing the firmware fb
drm/i915: Keep ring->active_list and ring->requests_list consistent
Linus Torvalds [Thu, 26 Mar 2015 21:11:17 +0000 (14:11 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A couple of bug fixes for s390.
The ftrace comile fix is quite large for a -rc6 release, but it would
be nice to have it in 4.0"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/smp: reenable smt after resume
s390/mm: limit STACK_RND_MASK for compat tasks
s390/ftrace: fix compile error if CONFIG_KPROBES is disabled
s390/cpum_sf: add diagnostic sampling event only if it is authorized
drm/i915: Fix modeset state confusion in the load detect code
But this time around it was the initial fb code that forgot to update
the plane->crtc pointer. Otherwise it's the exact same bug, with the
exact same restrains (any set_config call/ioctl that doesn't disable
the pipe papers over the bug for free, so fairly hard to hit in normal
testing). So if you want the full explanation just go read that one
over there - it's rather long ...
Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Josh Boyer <jwboyer@fedoraproject.org> Cc: Jani Nikula <jani.nikula@linux.intel.com> Reported-and-tested-by: Josh Boyer <jwboyer@fedoraproject.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: backported to drm-intel-fixes for v4.0-rc]
Reference: http://mid.gmane.org/CA+5PVA7ChbtJrknqws1qvZcbrg1CW2pQAFkSMURWWgyASRyGXg@mail.gmail.com Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Hui Wang [Thu, 26 Mar 2015 09:14:55 +0000 (17:14 +0800)]
ALSA: hda - Add one more node in the EAPD supporting candidate list
We have a HP machine which use the codec node 0x17 connecting the
internal speaker, and from the node capability, we saw the EAPD,
if we don't set the EAPD on for this node, the internal speaker
can't output any sound.
Maxime Ripard [Thu, 26 Mar 2015 09:27:09 +0000 (10:27 +0100)]
clocksource/drivers/sun5i: Fix cpufreq interaction with sched_clock()
The sun5i timer is used as the sched-clock on certain systems, and ever
since we started using cpufreq, the cpu clock (that is one of the
timer's clock indirect parent) now changes as well, along with the
actual sched_clock() rate.
This is not accurate and not desirable.
We can safely remove the sun5i sched-clock on those systems, since we
have other reliable sched_clock() sources in the system.
Tested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[ Improved the changelog. ] Cc: richard@nod.at Link: http://lkml.kernel.org/r/1427362029-6511-4-git-send-email-daniel.lezcano@linaro.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
clocksource/drivers: Fix various !CONFIG_HAS_IOMEM build errors
Fix !CONFIG_HAS_IOMEM related build failures in three clocksource drivers.
The build failures have the pattern of:
drivers/clocksource/sh_cmt.c: In function ‘sh_cmt_map_memory’: drivers/clocksource/sh_cmt.c:920:2:
error: implicit declaration of function ‘ioremap_nocache’ [-Werror=implicit-function-declaration] cmt->mapbase = ioremap_nocache(mem->start, resource_size(mem));
Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: maxime.ripard@free-electrons.com Link: http://lkml.kernel.org/r/1427362029-6511-1-git-send-email-daniel.lezcano@linaro.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Chris Wilson [Wed, 18 Mar 2015 18:19:22 +0000 (18:19 +0000)]
drm/i915: Keep ring->active_list and ring->requests_list consistent
If we retire requests last, we may use a later seqno and so clear
the requests lists without clearing the active list, leading to
confusion. Hence we should retire requests first for consistency with
the early return. The order used to be important as the lifecycle for
the object on the active list was determined by request->seqno. However,
the requests themselves are now reference counted removing the
constraint from the order of retirement.
drm/i915: Convert 'i915_seqno_passed' calls into 'i915_gem_request_completed
'
and a
WARNING: CPU: 0 PID: 1383 at drivers/gpu/drm/i915/i915_gem_evict.c:279 i915_gem_evict_vm+0x10c/0x140()
WARN_ON(!list_empty(&vm->active_list))
Identified by updating WATCH_LISTS:
[drm:i915_verify_lists] *ERROR* blitter ring: active list not empty, but no requests
WARNING: CPU: 0 PID: 681 at drivers/gpu/drm/i915/i915_gem.c:2751 i915_gem_retire_requests_ring+0x149/0x230()
WARN_ON(i915_verify_lists(ring->dev))
Note that this is only a problem in evict_vm where the following happens
after a retire_request has cleaned out all requests, but not all active
bo:
- intel_ring_idle called from i915_gpu_idle notices that no requests are
outstanding and immediately returns.
- i915_gem_retire_requests_ring called from i915_gem_retire_requests also
immediately returns when there's no request, still leaving the bo on the
active list.
- evict_vm hits the WARN_ON(!list_empty(&vm->active_list)) after evicting
all active objects that there's still stuff left that shouldn't be
there.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: John Harrison <John.C.Harrison@Intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Libin Yang [Thu, 26 Mar 2015 05:28:39 +0000 (13:28 +0800)]
ALSA: hda_intel: apply the Seperate stream_tag for Sunrise Point
The total stream number of Sunrise Point's input and output stream
exceeds 15, which will cause some streams do not work because
of the overflow on SDxCTL.STRM field if using the legacy
stream tag allocation method.
This patch uses the new stream tag allocation method by add
the flag AZX_DCAPS_SEPARATE_STREAM_TAG for Skylake platform.
Signed-off-by: Libin Yang <libin.yang@intel.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vineet Gupta [Thu, 26 Mar 2015 05:44:41 +0000 (11:14 +0530)]
ARC: signal handling robustify
A malicious signal handler / restorer can DOS the system by fudging the
user regs saved on stack, causing weird things such as sigreturn returning
to user mode PC but cpu state still being kernel mode....
Ensure that in sigreturn path status32 always has U bit; any other bogosity
(gargbage PC etc) will be taken care of by normal user mode exceptions mechanisms.
Vineet Gupta [Thu, 26 Mar 2015 03:55:44 +0000 (09:25 +0530)]
ARC: SA_SIGINFO ucontext regs off-by-one
The regfile provided to SA_SIGINFO signal handler as ucontext was off by
one due to pt_regs gutter cleanups in 2013.
Before handling signal, user pt_regs are copied onto user_regs_struct and copied
back later. Both structs are binary compatible. This was all fine until
commit 2fa919045b72 (ARC: pt_regs update #2) which removed the empty stack slot
at top of pt_regs (corresponding to first pad) and made the corresponding
fixup in struct user_regs_struct (the pad in there was moved out of
@scratch - not removed altogether as it is part of ptrace ABI)
struct user_regs_struct {
+ long pad;
struct {
- long pad;
long bta, lp_start, lp_end,....
} scratch;
...
}
This meant that now user_regs_struct was off by 1 reg w.r.t pt_regs and
signal code needs to user_regs_struct.scratch to reflect it as pt_regs,
which is what this commit does.
This problem was hidden for 2 years, because both save/restore, despite
using wrong location, were using the same location. Only an interim
inspection (reproducer below) exposed the issue.
Kinglong Mee [Sun, 22 Mar 2015 14:17:20 +0000 (22:17 +0800)]
NFSD: Fix bad update of layout in nfsd4_return_file_layout
With return layout as, (seg is return layout, lo is record layout)
seg->offset <= lo->offset and layout_end(seg) < layout_end(lo),
nfsd should update lo's offset to seg's end,
and,
seg->offset > lo->offset and layout_end(seg) >= layout_end(lo),
nfsd should update lo's end to seg's offset.
Fixes: 9cf514ccfa ("nfsd: implement pNFS operations") Signed-off-by: Kinglong Mee <kinglongmee@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com>