Current FSI driver is using set_rate call back function which is for
master mode.
By this patch, it is used from fsi_set_master_clk.
This patch is preparation of cleanup suspend/resume patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: soc-cache: Cache a pointer to the last accessed rbnode
Whenever we are doing a read or a write through the rbtree code, we'll
cache a pointer to the rbnode. To avoid looking up the register
everytime we do a read or a write, we first check if it can be found in
the cached register block, otherwise we traverse the rbtree and finally
cache the rbnode for future use.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch prepares the ground for the actual rbtree optimization patch
which will save a pointer to the last accessed rbnode that was used
in either the read() or write() functions.
Each rbnode manages a variable length block of registers. There can be no
two nodes with overlapping blocks. Each block has a base register and a
currently top register, all the other registers, if any, lie in between these
two and in ascending order.
The reasoning behind the construction of this rbtree is simple. In the
snd_soc_rbtree_cache_init() function, we iterate over the register defaults
provided by the driver. For each register value that is non-zero we
insert it in the rbtree. In order to determine in which rbnode we need
to add the register, we first look if there is another register already
added that is adjacent to the one we are about to add. If that is the case
we append it in that rbnode block, otherwise we create a new rbnode
with a single register in its block and add it to the tree.
In the next patch, where a cached rbnode is used by both the write() and the
read() functions, we also check if the register we are about to add is in the
cached rbnode (the least recently accessed one) and if so we append it in that
rbnode block.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Mon, 9 May 2011 22:32:03 +0000 (16:32 -0600)]
ASoC: WM8903: Fix Digital Capture Volume range
Increase the range of the Digital Capture Volume control to be 120 steps.
Each step is 0.75dB, and the range starts at -72dB, giving a max setting
of 18dB, which matches the latest datasheet, to the precision of the step
size.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The SSM2604 is basically a lightweight variant of the SSM2602 with a compatible
register layout. Thus we can easily support both devices by the same driver,
by providing a slightly set of controls, widgets and routes.
Compared to the SSM2602 the SSM2604 has no microphone input and no headphone
output.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is not required to have the codec powered at this stage and DAPM will power
the ADC and DAC down again after probe has run anyway.
Thus we avoid some unnecessary writes by this change.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Define POWER_OFF_ON_STANDBY cause trobles when trying to get some
sound from codec because code for bias setup was not compiled
(define wasn't defined). This define was removed in commit: cc3202f5 but again introduced by commit: f0fba2ad1 which then
completely break codec functionality so remove it again.
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
There are currently two controls which allow selecting the capture source, one
as a normal control, the other as part of a DAPM_MUX widget.
Remove the normal control.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: Create codec DAPM widgets before calling the codecs probe function
This allows to create DAPM routes depending on those widgets in the
codecs probe function. This is helpful when supporting similar codecs
with minor differences in the DAPM routing with the same driver.
Something similar has already been done for cards in commit a841ebb9 (ASoC: Create card DAPM widgets early so they can be used in
callbacks).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 3 May 2011 17:25:34 +0000 (18:25 +0100)]
ASoC: Don't crash on PM operations
The move over to exposing snd_soc_register_card() let the initialisation
of the driver data we use to find the card in PM operations go AWOL. Fix
this by setting the driver data when we register the card.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com>
This is useful when a single register bit or field affects multiple
muxes at once. The common case is to have separate control bits or
fields for each mux (channel). An alternative way of looking at this
is that the mux is a stereo (or even n-channel) mux, rather than
independant mono muxes.
Without this change, a separate kcontrol will be created for each
DAPM_MUX. This has the following disadvantages:
* Confuses the user/programmer with redundant controls that don't
map to separate hardware.
* When one of the controls is changed, ASoC fails to update the DAPM
logic for paths solely affected by the other controls impacted by
the same register bits. This causes some paths not to be correctly
powered up or down. Prior to this change, to work around this, the
user or programmer had to manually toggle all duplicate controls away
from the intended setting, and then back to it.
Control sharing implies that the control is named based on the
kcontrol_new itself, not any of the widgets that are affected by it.
Control sharing is implemented by: When creating kcontrols, if a
kcontrol does not yet exist for a particular kcontrol_new, then a new
kcontrol is created with a list of widgets containing just a single
entry. This is the normal case. However, if a kcontrol does already
exists for the given kcontrol_new, the current widget is simply added
to that kcontrol's list of affected widgets.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Thu, 28 Apr 2011 23:38:00 +0000 (17:38 -0600)]
ASoC: Store a list of widgets in a DAPM mux/mixer kcontrol
A future change will allow multiple widgets to be affected by the same
control. For example, a single register bit that controls separate muxes
in both the L and R audio paths.
This change updates the code that handles relevant controls to be able
to iterate over a list of affected widgets. Note that only the put
functions need significant modification to implement the iteration; the
get functions do not need to iterate, nor unify the results, since all
affected widgets reference the same kcontrol.
When creating the list of widgets, always create a 1-sized list, since
the control sharing is not implemented in this change.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Thu, 28 Apr 2011 23:37:59 +0000 (17:37 -0600)]
ASoC: Add w->kcontrols, and populate it
Future changes will need reference to the kcontrol created for a given
kcontrol_new. Store the created kcontrol values now.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Thu, 28 Apr 2011 23:37:58 +0000 (17:37 -0600)]
ASoC: s/w->kcontrols/w->kcontrol_news/g
A future change will modify struct snd_soc_dapm_widget to store the
actual kcontrol pointers for each kcontrol_new in a field named
kcontrols. Rename the existing kcontrols field to enable this.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The i2s shutdown callback has the check whether it should be disabled reversed.
Currently it is disabled if another stream is still active, but kept enabled if
the last stream is closed. This patch fixes it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: Move DAPM widget debugfs entry creation to snd_soc_dapm_new_widgets
Currently debugfs entries for a DAPM widgets are only added in
snd_soc_dapm_debugfs_init. If a widget is added later (for example in the
dai_link's probe callback) it will not show up in debugfs.
This patch moves the creation of the widget debugfs entry to
snd_soc_dapm_new_widgets where it will be added after the widget has been
properly instantiated.
As a side-effect this will also reduce the number of times the DAPM widget list
is iterated during a card's instantiation.
Since it is possible that snd_soc_dapm_new_widgets is invoked form the codecs or
cards probe callbacks, the creation of the debugfs dapm directory has to be
moved before these are called.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: Move DAPM debugfs directory creation to snd_soc_dapm_debugfs_init
Move the creation of the DAPM debugfs directory to snd_soc_dapm_debugfs_init
instead of having the same duplicated code in both codec and card DAPM setup.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mike Rapoport [Tue, 26 Apr 2011 08:52:42 +0000 (11:52 +0300)]
ASoC: tegra: TrimSlice machine support
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Takashi Iwai [Tue, 3 May 2011 10:50:29 +0000 (12:50 +0200)]
ASoC: Declare const properly for enum texts
The enum texts are supposed to be const char * const []. Without the
second const, it gets compile warnings like
sound/soc/codecs/max98095.c:607:2: warning: initialization discards qualifiers from pointer target type
This patch adds a helper function for searching DAPM widgets by name.
This allows to streamline functions which operate on widgets by name.
It also allows to get rid of copy'n'pasted code which was added to fallback to
widgets from other contexts if the widget was not found in the current context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 27 Apr 2011 17:16:32 +0000 (18:16 +0100)]
ASoC: Add more natural support for no-DMA DAIs
Since we can now support multiple platforms allow machines to not specify
a platform in a DAI link. Since the rest of the code requires that we have
a struct device for all objects we do this by substituting in a dummy
device that we register automatically.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Jassi Brar <jassisinghbrar@gmail.com> Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Mon, 25 Apr 2011 17:27:35 +0000 (18:27 +0100)]
ASoC: Don't warn if the WM8962 SYSCLK FLL setting doesn't match reality
When bringing up audio low power modes boards may configure SYSCLK before
they actually start the FLL as we do much of the clocking setup prior to
the power up sequence.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Mon, 25 Apr 2011 19:14:21 +0000 (20:14 +0100)]
ASoC: Implement WM8962 DMIC support
DMIC support is automatically disabled when none of the GPIOs are set up
to bring out the DMICCLK and DMICDAT pins at startup.
Note that there's no support for controlling DMIC routing except the power
control so the board DAPM configuration will need to manage DMIC enable and
disable if analogue mics (eg, a headset) also exist.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com>
Ben Gardiner [Thu, 21 Apr 2011 18:19:04 +0000 (14:19 -0400)]
davinci-mcasp: fix _CBM_CFS pin directions
The current davinci_mcasp_set_dai_fmt() sets bits ACLKX and ACLKR in the PDIR
register for the codec clock-master/frame-slave mode; however, this results in
the ACLKX and ACLKR pins being outputs according to SPRUFM1 [1] which
conflicts with "codec is clock master."
Similarly to the previous patch in this series, "fix _CBM_CFS hw_params" --
For codec clock-master/frame-slave mode (_CMB_CFS), clear bits ACLKX and ACLKR
in the PDIR register to set the pins as inputs and hence allow externally
sourced bit-clocks.
[1] http://www.ti.com/litv/pdf/sprufm1
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Reviewed-by: James Nuss <jamesnuss@nanometrics.ca> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ben Gardiner [Thu, 21 Apr 2011 18:19:03 +0000 (14:19 -0400)]
davinci-mcasp: fix _CBM_CFS hw_params
The current davinci_mcasp_set_dai_fmt() sets bits ACLKXE and ACLKRE (CLKXM
and CLKRM as they are reffered to in SPRUFM1 [1]) for codec clock-slave/
frame-slave mode (_CBS_CFS) which selects internally generated bit-clock and
frame-sync signals; however, it does the same thing again for codec
clock-master/frame-slave mode (_CBM_CFS) in the very next case statement which
is incorrectly selecting internally generated bit-clocks in this mode.
For codec clock-master/frame-slave mode (_CBM_CFS), clear bits ACLKXE and
ACLKRE to select externally-generated bit-clocks.
[1] http://www.ti.com/litv/pdf/sprufm1
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Reviewed-by: James Nuss <jamesnuss@nanometrics.ca> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ben Gardiner [Thu, 21 Apr 2011 18:19:02 +0000 (14:19 -0400)]
davinci-mcasp: use bitfield definitions for PDIR
The current driver creates value for set/clr of PDIR using (x<<26) instead
of the #defines that are convieniently made available.
Update the driver to use the bitfield definitions of PDIR. There is no
functional change introduced by this patch.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Reviewed-by: James Nuss <jamesnuss@nanometrics.ca> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ben Gardiner [Thu, 21 Apr 2011 18:19:01 +0000 (14:19 -0400)]
ASoC: davinci-mcasp: correct tdm_slots limit
The current check for the number of tdm-slots specified by platform data is
always true (x >= 2 || x <= 32); therefore the else branch that warns of an
incorrect number of slots can never be taken.
Check that the number of tdm slots specified by platform data is between 2
and 32, inclusive.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Reviewed-by: James Nuss <jamesnuss@nanometrics.ca> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: sh: fsi: Add module/port clock control function
The FIFO of each port were always working though it was not used
in current FSI driver.
This patch add module/port clock control function for fixing it.
This patch is also caring suspend/resume.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Reviewed-by: Simon Horman <simon@horms.net> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current FSI driver sets important settings when probing.
And it are not set again as long as driver is not bind again.
This mean FSI driver will lost it from register
if suspend/resume are happen.
This patch save important settings for suspend/resume.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Reviewed-by: Simon Horman <simon@horms.net> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If FSI port is clock master, it use set_rate function
which is callback from platform,
and it is not necessary to call it if FSI port is clock slave.
Current FSI driver called this callback if platform provide it.
This patch modify it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Reviewed-by: Simon Horman <simon@horms.net> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Tue, 19 Apr 2011 16:18:01 +0000 (10:18 -0600)]
ARM: Tegra: select MACH_HAS_SND_SOC_TEGRA_WM8903
CONFIG_SND_SOC_TEGRA_WM8903 is useful for many Tegra boards. To avoid the
ASoC tegra/Kconfig enumerating them all, instead have the Tegra machine
Kconfig select MACH_HAS_SND_SOC_TEGRA_WM8903 where appropriate, and have
SND_SOC_TEGRA_WM8903 depend on this.
[Redid ASoC diff so it applies. -- broonie]
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Tue, 19 Apr 2011 02:58:11 +0000 (20:58 -0600)]
ASoC: WM8903: Implement DMIC support
In addition to the currently supported analog capture path, the WM8903
also supports digital mics.
The analog and digital capture paths are exclusive; a mux is present to
select the capture source.
Logically, the mux exists to select the decimator's input, from either
the ADC or DMIC block outputs. However, the ADC power domain also
includes the DMIC interface. Consequently, this change represents the
mux as existing immediately before the ADC, and selecting between the
Input PGA and DMIC block outputs.
An alternative might be to represent the mux in its correct location,
and associate the ADC power enable controls with both the real ADC, and
a fake ADC for the DMIC?
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Peter Hsiang [Wed, 20 Apr 2011 01:20:40 +0000 (18:20 -0700)]
ASoC: Add EQ and filter to max98095 CODEC driver
This patch adds the equalizer and biquad filter controls.
Signed-off-by: Peter Hsiang <peter.hsiang@maxim-ic.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Tue, 19 Apr 2011 21:25:12 +0000 (15:25 -0600)]
ASoC: Tegra: wm8903: s/code/data/ for control/widget/maps
Replace calls to a variety of registration functions by updating
struct snd_soc_card snd_soc_tegra_wm8903 to directly point at the
various control/widget/map tables instead. The ASoC core now
performs any required registration based on these data fields.
(Applying Mark's TrimSlice review comments to the existing driver)
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Tue, 19 Apr 2011 21:25:11 +0000 (15:25 -0600)]
ASoC: snd_soc_dapm_get_pin_status: Match other contexts too
Not all widgets on a card are within the codec's DAPM context. Fix
snd_soc_dapm_get_pin_status to search all contexts when looking for a
widget.
This change is required when modifying tegra_wm8903 to use
snd_soc_card.widgets rather than calling snd_soc_dapm_new_controls; the
former adds the widgets to the card's DAPM context, whereas tegra_wm8903
uses the codec's DAPM context when calling snd_soc_dapm_new_controls.
By code inspection, I suspect this also applies to Samsung Speyside.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Tue, 19 Apr 2011 21:25:10 +0000 (15:25 -0600)]
ASoC: Tegra: Retrieve card from DAPM context not codec
Card widgets are created in the card's DAPM context, not any codec's DAPM
context. Hence, w->codec==NULL. Instead, find the card from the widget
through the DAPM context of the widget, not the codec of the widget.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Tue, 19 Apr 2011 21:25:09 +0000 (15:25 -0600)]
ASoC: Tegra: Don't return mclk_changed from utils_set_rate
Only the clock programming code needs to know whether the clocks changed,
and that is encapsulated within tegra_asoc_utils_set_rate(). The machine
driver's call to snd_soc_dai_set_sysclk(codec_dai, ...) is safe
irrespective of whether the clocks changed.
(Applying Mark's TrimSlice review comments to the existing driver)
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When the driver is not initialized/registered, nothing should be touching
these fields anyway, so there's no point clearing them out.
(Applying Mark's TrimSlice review comments to the existing driver)
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This machine driver is a platform driver, and hence will only be
instantiated on the correct machines. Hence, there is no need to
check the current machine during probe.
(Applying Mark's TrimSlice review comments to the existing driver)
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Tue, 12 Apr 2011 17:40:39 +0000 (11:40 -0600)]
ASoC: Tegra: Support more boards
* Ventana is identical to Harmony.
* Seaboard, Kaen, and Aebl are all pretty similar, mainly with slightly
different sets of GPIOs, and slightly different WM8903 pin connectivity.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Tue, 12 Apr 2011 17:40:38 +0000 (11:40 -0600)]
ASoC: Tegra: Don't store snd_soc_jack_gpio in an array
Storing the struct in an array makes the assignments to the GPIO member a
little non-obvious, and is pointless when there's only a single GPIO.
(I thought I fixed this during the review cycle when first submitting this
driver, but I guess I overlooked that)
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Tue, 12 Apr 2011 17:40:37 +0000 (11:40 -0600)]
ASoC: Tegra: Rename Kconfig SND_TEGRA_SOC_* to SND_SOC_TEGRA_*
The previous commit renames SND_TEGRA_SOC_HARMONY to SND_TEGRA_SOC_WM8903.
While we're breaking people's .config files, rename all Tegra/SOC-related
Kconfig variables to be more consistent with at least the core codec
variables. Note that there exist machines that name their variables both
ways.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Tue, 12 Apr 2011 17:40:36 +0000 (11:40 -0600)]
ASoC: Tegra: Rename harmony.c to tegra_wm8903.c
Soon, this machine driver will be updated to handle a number of Tegra boards
using the WM8903 codec. Rename the file in advance to reflect this.
Fix the content of tegra_wm8903.c to match the rename; replace references
to Harmony board with something more generic.
* s/struct tegra_harmony/struct tegra_wm8903/
* s/harmony/machine/ # variable name
* Similar rename for some functions
* Similar comment fix
* Similar MODULE_DESCRIPTION fix
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Tue, 12 Apr 2011 17:29:01 +0000 (11:29 -0600)]
ARM: Tegra: Add to tegra_wm8903_platform_data
Seaboard derivate Kaen has a GPIO to mute the headphone output. Add a field
to tegra_wm8903_platform_data so the board files can pass the GPIO number
for that to the ASoC machine driver.
Also, initialize this new field to a "not present" value for Harmony.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Tue, 12 Apr 2011 17:29:00 +0000 (11:29 -0600)]
ASoC: Tegra: Rename pdev tegra-snd-harmony to tegra-snd-wm8903
Soon, this machine driver will be updated to handle a number of Tegra boards
using the WM8903 codec. Rename the platform device in advance to reflect this.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: JZ4740: qi_lb60: Use gpio_request_array to request and setup gpios
This patch changes the qi_lb60 setup code to use gpio_request_array instead of
manually calling gpio_request and gpio_direction_output for each gpio.
Doing so makes the code a bit more compact.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
projects / linux-beck.git / log