Shawn Guo [Mon, 9 Dec 2013 06:42:54 +0000 (14:42 +0800)]
ARM: dts: vf610: make pinctrl nodes board specific
Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts. However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected. This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board. It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.
The patch provides a solution to avoid this device tree bloating problem
while still keeping boards share the common pinctrl setting data by
using DTC macro support. It creates <soc>-pingrp.h and move all those
pinctrl setting data into there as macro definitions. The <board>.dts
will instead define the pinctrl setting nodes that are necessary for the
board by referring to the macros in <soc>-pingrp.h, so that only the
pinctrl setting data that will be used by the board will get compiled
into the DTB for the board.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral. Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.
Denis Carikli [Thu, 5 Dec 2013 14:56:56 +0000 (15:56 +0100)]
ARM: dts: Add support for the cpuimx25 board from Eukrea and its baseboard.
The following devices/functionalities were added:
* Main and secondary UARTs.
* i2c and the pcf8563 device.
* Ethernet.
* NAND.
* The BP1 button.
* The LED.
* Watchdog
* SD.
Cc: Rob Herring <rob.herring@calxeda.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: devicetree@vger.kernel.org Cc: Sascha Hauer <kernel@pengutronix.de> Cc: linux-arm-kernel@lists.infradead.org Cc: Eric Bénard <eric@eukrea.com> Signed-off-by: Denis Carikli <denis@eukrea.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Eric Bénard [Thu, 5 Dec 2013 13:28:06 +0000 (14:28 +0100)]
ARM: mxs: Add support for the eukrea-cpuimx28.
The following devices/functionalities were tested:
* Main UART.
* Ethernet0.
* Ethernet1.
* SD.
* USB host.
* USB otg.
* Display(and its backlight).
* Touchscreen.
* Audio.
* nand.
* i2c and the pcf8563 device.
* The gpio buttons.
* The gpio leds.
* Watchdog
Cc: Rob Herring <rob.herring@calxeda.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: devicetree@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Eric Bénard <eric@eukrea.com> Signed-off-by: Denis Carikli <denis@eukrea.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Alexander Shiyan [Sat, 30 Nov 2013 07:03:20 +0000 (11:03 +0400)]
ARM: dts: i.MX27: Configure GPIOs as "input" by default
This patch changes the default direction for pins used
as GPIO to "input". This prevents a short circuit on the
configuration stage when GPIO-pin is connected to the
other output pin.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch updates FEC devicetree node of Phytec PCM038 module:
- Adding missing phy_mode properties.
- Adding fixed regulator to provide functionality without
dummy-regulator in the kernel.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Markus Pargmann [Wed, 20 Nov 2013 08:45:48 +0000 (09:45 +0100)]
ARM: dts: imx27 iomux device node
This patch adds a iomux node for imx27 pinctrl driver. The gpio
registers are embedded in the iomux memory area. So this patch moves
them into the iomux node for a better hardware description.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Maxime Ripard [Mon, 18 Nov 2013 14:37:52 +0000 (15:37 +0100)]
ARM: mxs: cfa10049: Add NAU7802 ADCs to the device tree
The Crystalfontz CFA-10049 has 3 Nuvoton NAU7802 ADCs, plugged behing a
GPIO-controlled I2C muxer because these ADCs don't have a configurable
address.
Marek Vasut [Sun, 17 Nov 2013 03:04:50 +0000 (04:04 +0100)]
ARM: dts: imx53: Add USB support for M53EVK
Add USB support for M53EVK. The configuration is such that USB Host1
port is used as Host and the USB OTG port is used as Peripheral thus
far. Once OTG is properly fixed, the OTG will be further adjusted.
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Marek Vasut [Sun, 17 Nov 2013 01:19:40 +0000 (02:19 +0100)]
ARM: dts: imx53: Fix backlight for M53EVK
Remove the PWM backlight pin from the hog pins list, so it doesn't
collide with the PWM pin group. Moreover, add dummy regulator for
the backlight so that the backlight driver probes correctly.
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Nicolin Chen [Fri, 15 Nov 2013 06:31:11 +0000 (14:31 +0800)]
ARM: dts: imx: specify the value of audmux pinctrl instead of 0x80000000
We must specify the value of audmux pinctrl if we want to use pinctrl_pm().
Thus change bypass value 0x80000000 to what we exactly need.
This patch also seperately unset PUE bit for TXD so that IOMUX won't pull
up/down the pin after turning into tristate. When we use SSI normal mode to
playback monaural audio via I2S signal, there'd be a pulled curve occur to
its signal at the second slot if setting PUE bit for TXD. And it will make
the second channel to play a constant noise. So by keeping the signal level
in the second slot, we can get a constant high level signal (-1) or a low
level one (0).
This patch updates i.MX51 CPU node:
- Alias for CPU is added to allow using this node in the parent DTS files.
- Removed useless "clock_names" property.
- "clock-latency" value increased to safe using with 32 kHz OSC.
- Defined operating points voltages and "voltage tolerance" properties.
Values are safe for both commercial and industrial CPU variants.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Shawn Guo [Wed, 6 Nov 2013 07:55:46 +0000 (15:55 +0800)]
ARM: dts: imx: use generic node name for fixed regulator
The device tree specification recommends that generic name should be
used for nodes. So instead of naming those fixed regulator nodes
arbitrarily, let's use the generic name 'regulator@num' for those nodes.
Shawn Guo [Mon, 4 Nov 2013 08:24:32 +0000 (16:24 +0800)]
ARM: dts: imx50: make pinctrl nodes board specific
Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts. However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected. This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board. It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.
The patch provides a solution to avoid this device tree bloating problem
while still keeping boards share the common pinctrl setting data by
using DTC macro support. It creates <soc>-pingrp.h and move all those
pinctrl setting data into there as macro definitions. The <board>.dts
will instead define the pinctrl setting nodes that are necessary for the
board by referring to the macros in <soc>-pingrp.h, so that only the
pinctrl setting data that will be used by the board will get compiled
into the DTB for the board.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral. Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.
Shawn Guo [Mon, 4 Nov 2013 08:05:37 +0000 (16:05 +0800)]
ARM: dts: imx51: make pinctrl nodes board specific
Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts. However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected. This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board. It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.
The patch provides a solution to avoid this device tree bloating problem
while still keeping boards share the common pinctrl setting data by
using DTC macro support. It creates <soc>-pingrp.h and move all those
pinctrl setting data into there as macro definitions. The <board>.dts
will instead define the pinctrl setting nodes that are necessary for the
board by referring to the macros in <soc>-pingrp.h, so that only the
pinctrl setting data that will be used by the board will get compiled
into the DTB for the board.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral. Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.
Shawn Guo [Mon, 4 Nov 2013 06:45:46 +0000 (14:45 +0800)]
ARM: dts: imx53: make pinctrl nodes board specific
Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts. However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected. This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board. It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.
The patch provides a solution to avoid this device tree bloating problem
while still keeping boards share the common pinctrl setting data by
using DTC macro support. It creates <soc>-pingrp.h and move all those
pinctrl setting data into there as macro definitions. The <board>.dts
will instead define the pinctrl setting nodes that are necessary for the
board by referring to the macros in <soc>-pingrp.h, so that only the
pinctrl setting data that will be used by the board will get compiled
into the DTB for the board.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral. Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.
Shawn Guo [Mon, 4 Nov 2013 02:49:04 +0000 (10:49 +0800)]
ARM: dts: imx6sl: make pinctrl nodes board specific
Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts. However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected. This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board. It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.
The patch provides a solution to avoid this device tree bloating problem
while still keeping boards share the common pinctrl setting data by
using DTC macro support. It creates <soc>-pingrp.h and move all those
pinctrl setting data into there as macro definitions. The <board>.dts
will instead define the pinctrl setting nodes that are necessary for the
board by referring to the macros in <soc>-pingrp.h, so that only the
pinctrl setting data that will be used by the board will get compiled
into the DTB for the board.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral. Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.
Shawn Guo [Wed, 23 Oct 2013 07:36:09 +0000 (15:36 +0800)]
ARM: dts: imx6qdl: make pinctrl nodes board specific
Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts. However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected. This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board. It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.
The patch provides a solution to avoid this device tree bloating problem
while still keeping boards share the common pinctrl setting data by
using DTC macro support. It creates <soc>-pingrp.h and move all those
pinctrl setting data into there as macro definitions. The <board>.dts
will instead define the pinctrl setting nodes that are necessary for the
board by referring to the macros in <soc>-pingrp.h, so that only the
pinctrl setting data that will be used by the board will get compiled
into the DTB for the board.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral. Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.
Valentin Raevsky [Tue, 29 Oct 2013 12:11:43 +0000 (14:11 +0200)]
ARM: dts: Add initial support for cm-fx6.
Add initial support for cm-fx6 module.
cm-fx6 is a module based on mx6q SoC with the following features:
- Up to 4GB of DDR3
- 1 LCD/DVI output port
- 1 HDMI output port
- 2 LVDS LCD ports
- Gigabit Ethernet
- Analog Audio
- CAN
- SATA
- NAND
- PCIE
This patch allows to boot up the module, configures the serial console,
the Ethernet adapter and the heartbeat led.
Denis Carikli [Wed, 23 Oct 2013 09:09:53 +0000 (11:09 +0200)]
ARM: dts: Add support for the cpuimx51 board from Eukrea and its baseboard.
The following devices/functionalities were added:
* Main and secondary UARTs.
* i2c and the pcf8563 device.
* Ethernet.
* NAND.
* The BP1 button.
* The LED.
* Watchdog
* SD.
Cc: Rob Herring <rob.herring@calxeda.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: devicetree@vger.kernel.org Cc: Sascha Hauer <kernel@pengutronix.de> Cc: linux-arm-kernel@lists.infradead.org Cc: Eric Bénard <eric@eukrea.com> Signed-off-by: Denis Carikli <denis@eukrea.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tim Harvey [Wed, 23 Oct 2013 04:51:26 +0000 (21:51 -0700)]
ARM: dts: add Gateworks Ventana support
The Gateworks Ventana product family consists of several baseboard designs
based on the Freescale i.MX6 family of processors. Each baseboard has a
different set of possible features.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
projects / karo-tx-linux.git / log