Sekhar Nori [Mon, 20 Dec 2010 16:01:34 +0000 (21:31 +0530)]
davinci: am18x/da850/omap-l138 evm: add support for higher speed grades
Apart from the regular AM18x/DA850/OMAP-L138 SoC operating
at 300MHz, these SoCs have variants that can operate at a
maximum of 456MHz. Variants at 408Mhz and 375 Mhz are available
as well.
Not all silicon is qualified to run at higher speeds and
unfortunately the maximum speed the chip can support can only
be determined from the label on the package (not software
readable).
The EVM hardware for all these variants is the same (except
for the actual SoC populated).
U-Boot on the EVM sets up ATAG_REVISION to inform the OS
regarding the speed grade supported by the silicon. We use
this information to pass on the speed grade information to
the SoC code.
Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Sekhar Nori [Mon, 20 Dec 2010 16:01:33 +0000 (21:31 +0530)]
davinci: am18x/da850/omap-l138: add support for higher speed grades
AM18x/DA850/OMAP-L138 SoCs have variants that can operate
at a maximum of 456 MHz at 1.3V operating point. Also the
1.2V operating point has a variant that can support a maximum
of 375 MHz.
This patch adds three new OPPs (456 MHz, 408 MHz and 372 MHz)
to the list of DA850 OPPs.
Not all silicon is qualified to run at higher speeds and
unfortunately the maximum speed the chip can support can only
be determined from the label on the package (not software
readable).
Because of this, we depend on the maximum speed grade information
to be provided to us in some board specific way. The board informs
the maximum speed grade information by setting the da850_max_speed
variable.
Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Ben Gardiner [Thu, 9 Dec 2010 21:51:06 +0000 (16:51 -0500)]
da850-evm: add baseboard GPIO expander buttons, switches and LEDs
This patch adds a pca953x platform device for the tca6416 found on the evm
baseboard. The tca6416 is a GPIO expander, also found on the UI board at a
separate I2C address. The pins of the baseboard IO expander are connected to
software reset, deep sleep enable, test points, a push button, DIP switches and
LEDs.
Add support for the push button, DIP switches and LEDs and test points (as
free GPIOs). The reset and deep sleep enable connections are reserved by the
setup routine so that userspace can't toggle those lines.
The existing tca6416-keypad driver was not employed because there was no
apararent way to register the LEDs connected to gpio's on the tca6416 while
simultaneously registering the tca6416-keypad instance.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca> CC: Govindarajan, Sriramakrishnan <srk@ti.com> Reviewed-by: Sekhar Nori <nsekhar@ti.com> Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> CC: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Ben Gardiner [Thu, 9 Dec 2010 21:51:05 +0000 (16:51 -0500)]
da850-evm: extract defines for SEL{A,B,C} pins in UI expander
The setup and teardown methods of the UI expander reference the SEL_{A,B,C}
pins by 'magic number' in each function. This uses the common enum for their offsets
in the expander setup and teardown functions.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca> Reviewed-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> CC: Victor Rodriguez <vm.rod25@gmail.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Ben Gardiner [Thu, 9 Dec 2010 21:51:04 +0000 (16:51 -0500)]
da850-evm: add UI Expander pushbuttons
This patch adds EV_KEYs for each of the 8 pushbuttons on the UI board via a
gpio-key device.
The expander is a tca6416; it controls the SEL_{A,B,C} lines which enable and
disable the peripherals found on the UI board in addition to the 8 pushbuttons
mentioned above. The reason the existing tca6416-keypad driver is not employed
is because there was no aparent way to keep the gpio lines used as
SEL_{A,B,C} registered while simultaneously registering the pushbuttons as a
tca6416-keypad instance.
Some experimentation with the polling interval was performed; we were searching
for the largest polling interval that did not affect the feel of the
responsiveness of the buttons. It is very subjective but 200ms seems to be a
good value that accepts firm pushes but rejects very light ones. The key values
assigned to the buttons were arbitrarily chosen to be F1-F8.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca> CC: Govindarajan, Sriramakrishnan <srk@ti.com> Reviewed-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> CC: Kevin Hilman <khilman@deeprootsystems.com> CC: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Marek Vasut [Tue, 19 Oct 2010 14:19:32 +0000 (16:19 +0200)]
ARM: pxa: Update Balloon3 for new FPGA firmware
The new FPGA firmware in Balloon3 uses different methods to control it's bus
control lines. In the new version, there are separate registers to set/clear
bus control lines. This patch updates affected places.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Mark F. Brown [Tue, 14 Dec 2010 03:56:59 +0000 (22:56 -0500)]
ARM: mmp: refactored 5V regulator support using fixed-regulator
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com> Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Marek Vasut [Wed, 11 Aug 2010 23:18:38 +0000 (01:18 +0200)]
ARM: pxa: Push Colibri evalboard MFP into module files
This change -- pushing the MFP configuration back into Module files -- is
necessary because some evalboards can be used with multiple modules, where MFP
differs from module to module. Therefore MFP isn't board-specific, but
module-specific and the module should preconfigure itself for the board.
(And there is also the C preprocesor limitation and conflicting #define-s)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Daniel Mack <daniel@caiaq.de> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Haojian Zhuang [Wed, 24 Nov 2010 03:54:25 +0000 (11:54 +0800)]
ARM: pxa: add iwmmx support for PJ4
iwmmxt is used in XScale, XScale3, Mohawk and PJ4 core. But the instructions
of accessing CP0 and CP1 is changed in PJ4. Append more files to support
iwmmxt in PJ4 core.
Signed-off-by: Zhou Zhu <zzhu3@marvell.com> Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Acked-by: Nicolas Pitre <nico@fluxnic.net> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Haojian Zhuang [Wed, 17 Nov 2010 11:03:36 +0000 (19:03 +0800)]
ARM: pxa: redefine irqs.h
Define all IRQs in irqs.h. If some IRQs are sharing one IRQ number, define
them together. If some IRQs are sharing same name with different IRQ number,
define different IRQ.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Cc: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Haojian Zhuang [Wed, 17 Nov 2010 11:03:35 +0000 (19:03 +0800)]
ARM: pxa: redefine the cpu_is_pxa3xx
After introducing pxa930/pxa935 and new silicons, original cpuid rules
of XScale generation 3 can't fit new silicons. Now redefine the rule
of PXA3xx.
Only PXA300/PXA310/PXA320/PXA930/PXA935 are family members of PXA3xx.
PXA930/PXA935 are family members of PXA93x. PXA93x can be considered
as PXA3xx + CP.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Cc: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Daniel Mack [Thu, 4 Nov 2010 18:44:00 +0000 (14:44 -0400)]
video: add driver for PXA3xx 2D graphics accelerator
This adds a driver for the the 2D graphics accelerator found on PXA3xx
processors. Only resource mapping, interrupt handling and a simple ioctl
handler is done by the kernel part, the rest of the logic is implemented
in DirectFB userspace.
Graphic applications greatly benefit for line drawing, blend, and
rectangle and triangle filling operations.
Benchmarks done on a PXA303 using the df_dok benchmarking tool follow,
where the value in square brackets show the CPU usage during that test.
Without accelerator (benchmarking 256x252 on 480x262 RGB16 (16bit)):
Signed-off-by: Daniel Mack <daniel@caiaq.de> Tested-by: Sven Neumann <s.neumann@raumfeld.com> Cc: Eric Miao <eric.y.miao@gmail.com> Cc: Denis Oliver Kropp <dok@directfb.org> Cc: Sven Neumann <s.neumann@raumfeld.com> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Marek Vasut [Wed, 3 Nov 2010 15:29:35 +0000 (16:29 +0100)]
ARM: pxa: Access SMEMC via virtual addresses
This is important because on PXA3xx, the physical mapping of SMEMC registers
differs from the one on PXA2xx. In order to get PCMCIA working on both PXA2xx
and PXA320, the PCMCIA driver was adjusted accordingly as well.
Also, various places in the kernel had to be patched to use
__raw_read/__raw_write.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Eric Miao [Wed, 13 Oct 2010 02:38:56 +0000 (10:38 +0800)]
ARM: pxa: remove un-used mapping of camera registers
The camera registers start and range are encoded into the platform
device, and are actually handled by ioremap()'ed, thus the mapping
in pxa_map_io() is not necessary.
Linus Torvalds [Wed, 15 Dec 2010 20:41:17 +0000 (12:41 -0800)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix typo which broke '..' detection in ext4_find_entry()
ext4: Turn off multiple page-io submission by default
The install_special_mapping routine (used, for example, to setup the
vdso) skips the security check before insert_vm_struct, allowing a local
attacker to bypass the mmap_min_addr security restriction by limiting
the available pages for special mappings.
bprm_mm_init() also skips the check, and although I don't think this can
be used to bypass any restrictions, I don't see any reason not to have
the security check.
Will Deacon [Wed, 1 Dec 2010 17:37:45 +0000 (17:37 +0000)]
ARM: hw_breakpoint: do not fail initcall if monitor mode is disabled
The debug registers can only be manipulated from software if monitor
debug mode is enabled. On some cores, this can never be enabled (i.e.
the corresponding bit in the DSCR is RAZ/WI).
This patch ensures we can handle this hardware configuration and fail
gracefully, rather than blow up the kernel during boot.
Reported-by: Cyril Chemparathy <cyril@ti.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
arch/x86/crypto/ghash-clmulni-intel_glue.c:256: error: implicit declaration of function 'IS_ERR'
arch/x86/crypto/ghash-clmulni-intel_glue.c:257: error: implicit declaration of function 'PTR_ERR'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Linus Torvalds [Wed, 15 Dec 2010 02:50:10 +0000 (18:50 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: It is likely that WORKER_NOT_RUNNING is true
MAINTAINERS: Add workqueue entry
workqueue: check the allocation of system_unbound_wq
Linus Torvalds [Wed, 15 Dec 2010 02:49:40 +0000 (18:49 -0800)]
Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md:
md: protect against NULL reference when waiting to start a raid10.
md: fix bug with re-adding of partially recovered device.
md: fix possible deadlock in handling flush requests.
md: move code in to submit_flushes.
md: remove handling of flush_pending in md_submit_flush_data
Major Lee [Fri, 10 Dec 2010 10:13:49 +0000 (10:13 +0000)]
dw_spi: Fix missing final read in some polling situations
There is a possibility that the last word of a transaction will be lost
if data is not ready. Re-read in poll_transfer() to solve this issue
when poll_mode is enabled.
Verified on SPI touch screen device.
Signed-off-by: Major Lee <major_lee@wistron.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 14 Dec 2010 15:29:08 +0000 (15:29 +0000)]
i2c_intel_mid: Fix slash in sysfs name
This gets caught by the new sanity check code. Instead of the slash use a
different symbol. This was originally found by Major Lee who proposed a
rather more complex patch which changed the name according to the chip
type.
On the basis that we are in a late -rc and making Linus grumpy isn't always
a good idea (however fun) this is a simple alternative.
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 15 Dec 2010 01:36:10 +0000 (17:36 -0800)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6535/1: V6 MPCore v6_dma_inv_range and v6_dma_flush_range RWFO fix
ARM: 6534/1: Make CONFIG_FPE_NWFPE depend on !CONFIG_THUMB2_KERNEL
ARM: 6533/1: Thumb-2: Make CONFIG_THUMB2_KERNEL depend on !CPU_V6
Change bcmring Maintainer list.
ARM: Update mach-types
ARM: 6528/1: Use CTR for the I-cache line size on ARMv7
ARM: 6527/1: Use CTR instead of CCSIDR for the D-cache line size on ARMv7
ARM: pxa/palm: fix ifdef around gen_nand driver registration
ARM: pxa: fix pxa2xx-flash section mismatch
ARM: mmp2: remove not used clk_rtc
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: Write to prom console using indirect buffer.
sparc: Delete prom_*getchar().
sparc: Pass buffer pointer all the way down to prom_{get,put}char().
sparc: Do not export prom_nb{get,put}char().
sparc64: Delete prom_setcallback().
sparc64: Unexport prom_service_exists().
sparc: Kill prom devops_{32,64}.c
sparc: Remove prom_pathtoinode()
sparc64: Delete prom_puts() unused.
SPARC/LEON: removed constant timer initialization as if HZ=100, now it reflects the value of HZ
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (75 commits)
pppoe.c: Fix kernel panic caused by __pppoe_xmit
WAN: Fix a TX IRQ causing BUG() in PC300 and PCI200SYN drivers.
bnx2x: Advance a version number to 1.60.01-0
bnx2x: Fixed a compilation warning
bnx2x: LSO code was broken on BE platforms
qlge: Fix deadlock when cancelling worker.
net: fix skb_defer_rx_timestamp()
cxgb4vf: Ingress Queue Entry Size needs to be 64 bytes
phy: add the IC+ IP1001 driver
atm: correct sysfs 'device' link creation and parent relationships
MAINTAINERS: remove me from tulip
SCTP: Fix SCTP_SET_PEER_PRIMARY_ADDR to accpet v4mapped address
enic: Bug Fix: Pass napi reference to the isr that services receive queue
ipv6: fix nl group when advertising a new link
connector: add module alias
net: Document the kernel_recvmsg() function
r8169: Fix runtime power management
hso: IP checksuming doesn't work on GE0301 option cards
xfrm: Fix xfrm_state_migrate leak
net: Convert netpoll blocking api in bonding driver to be a counter
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] hpsa: fix redefinition of PCI_DEVICE_ID_CISSF
[SCSI] qla2xxx: Update version number to 8.03.05-k0.
[SCSI] qla2xxx: Properly set the return value in qla2xxx_eh_abort function.
[SCSI] qla2xxx: Correct issue where NPIV-config data was not being allocated for 82xx parts.
[SCSI] qla2xxx: Change MSI initialization from using incorrect request_irq parameter.
[SCSI] qla2xxx: Populate Command Type 6 LUN field properly.
[SCSI] zfcp: Issue FCP command without holding SCSI host_lock
[SCSI] zfcp: Prevent usage w/o holding a reference
[SCSI] zfcp: No ERP escalation on gpn_ft eval
[SCSI] zfcp: Correct false abort data assignment.
[SCSI] zfcp: Fix common FCP request reception
[SCSI] Eliminate error handler overload of the SCSI serial number
[SCSI] pmcraid: disable msix and expand device config entry
[SCSI] bsg: correct fault if queue object removed while dev_t open
[SCSI] osd: checking NULL instead of ERR_PTR()
Linus Torvalds [Tue, 14 Dec 2010 22:35:04 +0000 (14:35 -0800)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdboc,input: Fix regression with keyboard release key and early debugging
Linus Torvalds [Tue, 14 Dec 2010 22:33:33 +0000 (14:33 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI / PM: Do not save/restore NVS on Sony Vaio VGN-NW130D
ACPI/HEST: adjust section selection
ACPI: eliminate unused variable warning for !ACPI_SLEEP
ACPI/PNP: avoid section mismatch warning
ACPI thermal: remove two unused functions
ACPI: fix a section mismatch
ACPI, APEI, use raw spinlock in ERST
ACPI: video: fix build for CONFIG_ACPI=n
ACPI: video: fix build for VIDEO_OUTPUT_CONTROL=n
ACPI: fix allowing to add/remove multiple _OSI strings
acpi: fix _OSI string setup regression
ACPI: EC: Add another dmi match entry for MSI hardware
ACPI battery: update status upon sysfs query
ACPI ac: update AC status upon sysfs query
ACPI / PM: Do not refcount power resources that can't be turned on
ACPI / PM: Check device state before refcounting power resources
ARM: 6535/1: V6 MPCore v6_dma_inv_range and v6_dma_flush_range RWFO fix
Cache ownership must be acquired by reading/writing data from the
cache line to make cache operation have the desired effect on the
SMP MPCore CPU. However, the ownership is never acquired in the
v6_dma_inv_range function when cleaning the first line and
flushing the last one, in case the address is not aligned
to D_CACHE_LINE_SIZE boundary.
Fix this by reading/writing data if needed, before performing
cache operations.
While at it, fix v6_dma_flush_range to prevent RWFO outside
the buffer.
Cc: stable@kernel.org Signed-off-by: Valentine Barshak <vbarshak@mvista.com> Signed-off-by: George G. Davis <gdavis@mvista.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Mon, 13 Dec 2010 20:56:03 +0000 (21:56 +0100)]
ARM: 6534/1: Make CONFIG_FPE_NWFPE depend on !CONFIG_THUMB2_KERNEL
Because the nwfpe support is unlikely to be used on new platforms
and requires CONFIG_OABI_COMPAT, which is not generally used with
ARMv7+, we shouldn't expect to build nwfpe support into a Thumb-2
kernel.
At present, nwfpe contains assembly code which isn't Thumb-2
compatible, and for now it doesn't appear useful to port this
code.
All ARMv7-A/R platforms necessarily have VFPv3 hardware floating-
point natively, making emulation unnecessary.
Signed-off-by: Dave Martin <dave.martin@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Mon, 13 Dec 2010 20:53:53 +0000 (21:53 +0100)]
ARM: 6533/1: Thumb-2: Make CONFIG_THUMB2_KERNEL depend on !CPU_V6
This makes sense, because Thumb-2 code can't execute on plain
ARMv6 processors.
This will avoid accidentally configuring a broken kernel where the
config otherwise would allow multiple architecture versions to
coexist in the same kernel.
Not adding !CPU_V5 etc., because the chance of anyone trying to
put v5 and v7 in the same kernel is low, and I'm not aware of
any mach which can do this. These could be added later if it
matters.
Note that the rules may need to be refined if support for the
ARM1156J(F)-S processor is later added to the kernel, since this
processor supports the rare ARMv6T2 extensions, which add support
for Thumb-2 and a few other ARMv7 features.
Signed-off-by: Dave Martin <dave.martin@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jiandong Zheng [Tue, 14 Dec 2010 21:55:49 +0000 (21:55 +0000)]
Change bcmring Maintainer list.
I am Jiandong Zheng working on BCMRING in Broadcom Canada Ltd. I am
replacing Leo Chen (leochen@broadcom.com) as "ARM/BCMRING ARM
ARCHITECTURE" and "ARM/BCMRING MTD NAND DRIVER" maintainer from
Broadcom as he is no longer the maintainer of these components.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com> Acked-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Tue, 14 Dec 2010 21:33:21 +0000 (13:33 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: tps6586x: correct register table
regulator: tps6586x: Handle both enable reg/bits being the same
regulator: tps6586x: Fix TPS6586X_DVM to store goreg/bit
regulator: tps6586x: Add missing bit mask generation
Linus Torvalds [Tue, 14 Dec 2010 21:32:40 +0000 (13:32 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: HDA: Quirk for Dell Vostro 320 to make microphone work
ALSA: hda - Reset sample sizes and max bitrates when reading ELD
ALSA: hda - Always allow basic audio irrespective of ELD info
ALSA: hda - Do not wrongly restrict min_channels based on ELD
ASoC: Correct WM8962 interrupt mask register read
ASoC: WM8580: Debug BCLK and sample size
ASoC: Fix resource leak if soc_register_ac97_dai_link failed
ASoC: Hold client_mutex while calling snd_soc_instantiate_cards()
ASoC: Fix swap of left and right channels for WM8993/4 speaker boost gain
ASoC: Fix off by one error in WM8994 EQ register bank size
ALSA: hda: Use position_fix=1 for Acer Aspire 5538 to enable capture on internal mic
ALSA: hda - Enable jack sense for Thinkpad Edge 13
ALSA: hda - Fix ThinkPad T410[s] docking station line-out
ALSA: hda: Use model=lg quirk for LG P1 Express to enable playback and capture
Linus Torvalds [Tue, 14 Dec 2010 21:31:49 +0000 (13:31 -0800)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: don't apply 7xx HDP flush workaround on AGP
drm: use after free in drm_queue_vblank_event()
drm/kms: remove spaces from connector names (v2)
Linus Torvalds [Tue, 14 Dec 2010 21:31:23 +0000 (13:31 -0800)]
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (adm1026) Allow 1 as a valid divider value
hwmon: (adm1026) Fix setting fan_div
hwmon: (it87) Fix manual fan speed control on IT8721F
Theodore Ts'o [Tue, 14 Dec 2010 20:27:50 +0000 (15:27 -0500)]
ext4: Turn off multiple page-io submission by default
Jon Nelson has found a test case which causes postgresql to fail with
the error:
psql:t.sql:4: ERROR: invalid page header in block 38269 of relation base/16384/16581
Under memory pressure, it looks like part of a file can end up getting
replaced by zero's. Until we can figure out the cause, we'll roll
back the change and use block_write_full_page() instead of
ext4_bio_write_page(). The new, more efficient writing function can
be used via the mount option mblk_io_submit, so we can test and fix
the new page I/O code.
To reproduce the problem, install postgres 8.4 or 9.0, and pin enough
memory such that the system just at the end of triggering writeback
before running the following sql script:
begin;
create temporary table foo as select x as a, ARRAY[x] as b FROM
generate_series(1, 10000000 ) AS x;
create index foo_a_idx on foo (a);
create index foo_b_idx on foo USING GIN (b);
rollback;
If the temporary table is created on a hard drive partition which is
encrypted using dm_crypt, then under memory pressure, approximately
30-40% of the time, pgsql will issue the above failure.
This patch should fix this problem, and the problem will come back if
the file system is mounted with the mblk_io_submit mount option.
Reported-by: Jon Nelson <jnelson@jamponi.net> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Linus Torvalds [Tue, 14 Dec 2010 19:09:05 +0000 (11:09 -0800)]
Merge branch 'for-2.6.37' of git://linux-nfs.org/~bfields/linux
* 'for-2.6.37' of git://linux-nfs.org/~bfields/linux:
nfsd: Fix possible BUG_ON firing in set_change_info
sunrpc: prevent use-after-free on clearing XPT_BUSY
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: prevent RAID level downgrades when space is low
Btrfs: account for missing devices in RAID allocation profiles
Btrfs: EIO when we fail to read tree roots
Btrfs: fix compiler warnings
Btrfs: Make async snapshot ioctl more generic
Btrfs: pwrite blocked when writing from the mmaped buffer of the same page
Btrfs: Fix a crash when mounting a subvolume
Btrfs: fix sync subvol/snapshot creation
Btrfs: Fix page leak in compressed writeback path
Btrfs: do not BUG if we fail to remove the orphan item for dead snapshots
Btrfs: fixup return code for btrfs_del_orphan_item
Btrfs: do not do fast caching if we are allocating blocks for tree_root
Btrfs: deal with space cache errors better
Btrfs: fix use after free in O_DIRECT
Linus Torvalds [Tue, 14 Dec 2010 19:02:15 +0000 (11:02 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: fix ioctl magic
ceph: Behave better when handling file lock replies.
ceph: pass lock information by struct file_lock instead of as individual params.
ceph: Handle file locks in replies from the MDS.
ceph: avoid possible null deref in readdir after dir llseek
Linus Torvalds [Tue, 14 Dec 2010 16:51:12 +0000 (08:51 -0800)]
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Fix panic after nfs_umount()
nfs: remove extraneous and problematic calls to nfs_clear_request
nfs: kernel should return EPROTONOSUPPORT when not support NFSv4
NFS: Fix fcntl F_GETLK not reporting some conflicts
nfs: Discard ACL cache on mode update
NFS: Readdir cleanups
NFS: nfs_readdir_search_for_cookie() don't mark as eof if cookie not found
NFS: Fix a memory leak in nfs_readdir
Call the filesystem back whenever a page is removed from the page cache
NFS: Ensure we use the correct cookie in nfs_readdir_xdr_filler
Steven Rostedt [Sat, 4 Dec 2010 04:12:33 +0000 (23:12 -0500)]
workqueue: It is likely that WORKER_NOT_RUNNING is true
Running the annotate branch profiler on three boxes, including my
main box that runs firefox, evolution, xchat, and is part of the distcc farm,
showed this with the likelys in the workqueue code:
The likely()s in this case were assuming that WORKER_NOT_RUNNING will
most likely be false. But this is not the case. The reason is
(and shown by adding trace_printks and testing it) that most of the time
WORKER_PREP is set.
In worker_thread() we have:
worker_clr_flags(worker, WORKER_PREP);
[ do work stuff ]
worker_set_flags(worker, WORKER_PREP, false);
(that 'false' means not to wake up an idle worker)
The wq_worker_sleeping() is called from schedule when a worker thread
is putting itself to sleep. Which happens most of the time outside
of that [ do work stuff ].
The wq_worker_waking_up is called by the wakeup worker code, which
is also callod outside that [ do work stuff ].
Thus, the likely and unlikely used by those two functions are actually
backwards.
Refresh rate nearness is not calculated or reset when nearest resolution
changes.
This patch resets the refresh rate differential measurement whenever a
new nearest resolution is discovered. This fixes two error cases;
first, wherein the first mode's refresh rate differential is never
calculated and second, when the closest refresh rate from a previous
nearest resolution is erroneously preserved.
Signed-off-by: Andrew Kephart <andrew.kephart@alereon.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Nicolas Ferre [Mon, 13 Dec 2010 12:48:41 +0000 (13:48 +0100)]
dmaengine: at_hdmac: fix buffer transfer size specification
Buffer transfer size is the number of transfers to be performed in
relation with the width of the _source_ interface.
So in the DMA_FROM_DEVICE case, it should be the register width that
should be taken into account.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>