Eric Dumazet [Thu, 26 Feb 2015 22:10:19 +0000 (14:10 -0800)]
tcp: tso: restore IW10 after TSO autosizing
With sysctl_tcp_min_tso_segs being 4, it is very possible
that tcp_tso_should_defer() decides not sending last 2 MSS
of initial window of 10 packets. This also applies if
autosizing decides to send X MSS per GSO packet, and cwnd
is not a multiple of X.
This patch implements an heuristic based on age of first
skb in write queue : If it was sent very recently (less than half srtt),
we can predict that no ACK packet will come in less than half rtt,
so deferring might cause an under utilization of our window.
This is visible on initial send (IW10) on web servers,
but more generally on some RPC, as the last part of the message
might need an extra RTT to get delivered.
Tested:
Ran following packetdrill test
// A simple server-side test that sends exactly an initial window (IW10)
// worth of packets.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 26 Feb 2015 22:10:18 +0000 (14:10 -0800)]
tcp: tso: remove tp->tso_deferred
TSO relies on ability to defer sending a small amount of packets.
Heuristic is to wait for future ACKS in hope to send more packets at once.
Current algorithm uses a per socket tso_deferred field as a pseudo timer.
This pseudo timer relies on future ACK, but there is no guarantee
we receive them in time.
Fix would be to use a real timer, but cost of such timer is probably too
expensive for typical cases.
This patch changes the logic to test the time of last transmit,
because we should not add bursts of more than 1ms for any given flow.
We've used this patch for about two years at Google, before FQ/pacing
as it would reduce a fair amount of bursts.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 26 Feb 2015 19:34:37 +0000 (19:34 +0000)]
usbnet: Fix tx_packets stat for FLAG_MULTI_FRAME drivers
Currently the usbnet core does not update the tx_packets statistic for
drivers with FLAG_MULTI_PACKET and there is no hook in the TX
completion path where they could do this.
cdc_ncm and dependent drivers are bumping tx_packets stat on the
transmit path while asix and sr9800 aren't updating it at all.
Add a packet count in struct skb_data so these drivers can fill it
in, initialise it to 1 for other drivers, and add the packet count
to the tx_packets statistic on completion.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Tested-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 27 Feb 2015 23:18:52 +0000 (18:18 -0500)]
Merge branch 'tipc-next'
Erik Hugne says:
====================
tipc: bug fix and some improvements
Most important is a fix for a nullptr exception that would occur when
name table subscriptions fail. The remaining patches are performance
improvements and cosmetic changes.
v2: remove unnecessary whitespace in patch #2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne [Fri, 27 Feb 2015 07:56:58 +0000 (08:56 +0100)]
tipc: make media address offset a common define
With the exception of infiniband media which does not use media
offsets, the media address is always located at offset 4 in the
media info field as defined by the protocol, so we move the
definition to the generic bearer.h
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne [Fri, 27 Feb 2015 07:56:57 +0000 (08:56 +0100)]
tipc: rename media/msg related definitions
The TIPC_MEDIA_ADDR_SIZE and TIPC_MEDIA_ADDR_OFFSET names
are misleading, as they actually define the size and offset of
the whole media info field and not the address part. This patch
does not have any functional changes.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne [Fri, 27 Feb 2015 07:56:56 +0000 (08:56 +0100)]
tipc: purge links when bearer is disabled
If a bearer is disabled by manual intervention, all links over that
bearer should be purged, indicated with the 'shutting_down' flag.
Otherwise tipc will get confused if a new bearer is enabled using
a different media type.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne [Fri, 27 Feb 2015 07:56:55 +0000 (08:56 +0100)]
tipc: fix nullpointer bug when subscribing to events
If a subscription request is sent to a topology server
connection, and any error occurs (malformed request, oom
or limit reached) while processing this request, TIPC should
terminate the subscriber connection. While doing so, it tries
to access fields in an already freed (or never allocated)
subscription element leading to a nullpointer exception.
We fix this by removing the subscr_terminate function and
terminate the connection immediately upon any subscription
failure.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne [Fri, 27 Feb 2015 07:56:54 +0000 (08:56 +0100)]
tipc: only create header copy for name distr messages
The TIPC name distributor pushes topology updates to the cluster
neighbors. Currently this is done in a unicast manner, and the
skb holding the update is cloned for each cluster member. This
is unnecessary, as we only modify the destnode field in the header
so we change it to do pskb_copy instead.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Wed, 25 Feb 2015 18:52:11 +0000 (19:52 +0100)]
team: allow TSO being set on master
This patch allows TSO being set/unset on the master, so that GSO
segmentation is done after team layer.
Similar patch is present for bonding: b0ce3508b25e ("bonding: allow TSO being set on bonding master")
and bridge: f902e8812ef6 ("bridge: Add ability to enable TSO")
Suggested-by: Jiri Prochazka <jprochaz@redhat.com> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch set removes the leaf_info structure from the IPv4 fib_trie. The
general idea is that the leaf_info structure itself only held about 6
actual bits of data, beyond that it was mostly just waste. As such we can
drop the structure, move the 1 byte representing the prefix/suffix length
into the fib_alias and just link it all into one list.
My testing shows that this saves somewhere between 4 to 10ns depending on
the type of test performed. I'm suspecting that this represents 1 to 2 L1
cache misses saved per look-up.
One side effect of this change is that semantic_match_miss will now only
increment once per leaf instead of once per leaf_info miss. However the
stat is already skewed now that we perform a preliminary check on the leaf
as a part of the look-up.
I also have gone through and addressed a number of ordering issues in the
first patch since I had misread the behavior of list_add_tail.
I have since run some additional testing and verified the resulting lists
are in the same order when combining multiple prefix length and tos values
in a single leaf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 25 Feb 2015 23:31:51 +0000 (15:31 -0800)]
fib_trie: Remove leaf_info
At this point the leaf_info hash is redundant. By adding the suffix length
to the fib_alias hash list we no longer have need of leaf_info as we can
determine the prefix length from fa_slen. So we can compress things by
dropping the leaf_info structure from fib_trie and instead directly connect
the leaves to the fib_alias hash list.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 25 Feb 2015 23:31:44 +0000 (15:31 -0800)]
fib_trie: Add slen to fib alias
Make use of an empty spot in the alias to store the suffix length so that
we don't need to pull that information from the leaf_info structure.
This patch also makes a slight change to the user statistics. Instead of
incrementing semantic_match_miss once per leaf_info miss we now just
increment it once per leaf if a match was not found.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 25 Feb 2015 23:31:37 +0000 (15:31 -0800)]
fib_trie: Replace plen with slen in leaf_info
This replaces the prefix length variable in the leaf_info structure with a
suffix length value, or host identifier length in bits. By doing this it
makes it easier to sort out since the tnodes and leaf are carrying this
value as well since it is compatible with the ->pos field in tnodes.
I also cleaned up one spot that had some list manipulation that could be
simplified. I basically updated it so that we just use hlist_add_head_rcu
instead of calling hlist_add_before_rcu on the first node in the list.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 25 Feb 2015 23:31:31 +0000 (15:31 -0800)]
fib_trie: Convert fib_alias to hlist from list
There isn't any advantage to having it as a list and by making it an hlist
we make the fib_alias more compatible with the list_info in terms of the
type of list used.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 27 Feb 2015 21:25:30 +0000 (16:25 -0500)]
Merge branch 'ip_level_multicast_join_leave'
Madhu Challa says:
====================
Multicast group join/leave at ip level
This series enables configuring multicast group join/leave at ip level
by extending the "ip address" command.
It adds a new control socket mc_autojoin_sock and ifa_flag IFA_F_MCAUTOJOIN
to invoke the corresponding igmp group join/leave api.
Since the igmp group join/leave api takes the rtnl_lock the code had to
be refactored by adding a shim layer prefixed by __ that can be invoked
by code that already has the rtnl_lock. This way we avoid proliferation of
work queues.
The first patch in this series does the refactoring for igmp v6.
Its based on igmp v4 changes that were added by Eric Dumazet.
The second patch in this series does the group join/leave based on the
setting of the IFA_F_MCAUTOJOIN flag.
v5:
- addressed comments from Daniel Borkmann.
- removed blank line in patch 1/2
- removed unused variable, const arg in patch 2/2
v4:
- addressed comments from Yoshifuji Hideaki.
- Remove WARN_ON not needed because we return a value from v2.
- addressed comments from Daniel Borkmann.
- rename sock to mc_autojoin_sk
- ip_mc_config() pass ifa so it needs one less argument.
- igmp_net_{init|destroy}() use inet_ctl_sock_{create|destroy}
- inet_rtm_newaddr() change scope of ret.
- igmp_net_init() no need to initialize sock to NULL.
v3:
- addressed comments from David Miller.
- fixed indentation and local variable order.
v2:
- addressed comments from Eric Dumazet.
- removed workqueue and call __ip_mc_{join|leave}_group or
__ipv6_sock_mc_{join|drop}
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Madhu Challa [Wed, 25 Feb 2015 17:58:35 +0000 (09:58 -0800)]
multicast: Extend ip address command to enable multicast group join/leave on
Joining multicast group on ethernet level via "ip maddr" command would
not work if we have an Ethernet switch that does igmp snooping since
the switch would not replicate multicast packets on ports that did not
have IGMP reports for the multicast addresses.
Linux vxlan interfaces created via "ip link add vxlan" have the group option
that enables then to do the required join.
By extending ip address command with option "autojoin" we can get similar
functionality for openvswitch vxlan interfaces as well as other tunneling
mechanisms that need to receive multicast traffic. The kernel code is
structured similar to how the vxlan driver does a group join / leave.
example:
ip address add 224.1.1.10/24 dev eth5 autojoin
ip address del 224.1.1.10/24 dev eth5
Signed-off-by: Madhu Challa <challa@noironetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Madhu Challa [Wed, 25 Feb 2015 17:58:34 +0000 (09:58 -0800)]
igmp v6: add __ipv6_sock_mc_join and __ipv6_sock_mc_drop
Based on the igmp v4 changes from Eric Dumazet. 959d10f6bbf6("igmp: add __ip_mc_{join|leave}_group()")
These changes are needed to perform igmp v6 join/leave while
RTNL is held.
Make ipv6_sock_mc_join and ipv6_sock_mc_drop wrappers around
__ipv6_sock_mc_join and __ipv6_sock_mc_drop to avoid
proliferation of work queues.
Signed-off-by: Madhu Challa <challa@noironetworks.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Tue, 24 Feb 2015 17:17:31 +0000 (09:17 -0800)]
udp: In udp_flow_src_port use random hash value if skb_get_hash fails
In the unlikely event that skb_get_hash is unable to deduce a hash
in udp_flow_src_port we use a consistent random value instead.
This is specified in GRE/UDP draft section 3.2.1:
https://tools.ietf.org/html/draft-ietf-tsvwg-gre-in-udp-encap-04
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu [Thu, 26 Feb 2015 07:55:40 +0000 (23:55 -0800)]
bridge: fix link notification skb size calculation to include vlan ranges
my previous patch skipped vlan range optimizations during skb size
calculations for simplicity.
This incremental patch considers vlan ranges during
skb size calculations. This leads to a bit of code duplication
in the fill and size calculation functions. But, I could not find a
prettier way to do this. will take any suggestions.
Previously, I had reused the existing br_get_link_af_size size calculation
function to calculate skb size for notifications. Reusing it this time
around creates some change in behaviour issues for the usual
.get_link_af_size callback.
This patch adds a new br_get_link_af_size_filtered() function to
base the size calculation on the incoming filter flag and include
vlan ranges.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Reviewed-by: Scott Feldman <sfeldma@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 26 Feb 2015 16:22:03 +0000 (11:22 -0500)]
Merge branch 'rocker-next'
Scott Feldman says:
====================
rocker cleanups
Pushing out some rocker cleanups I've had in my queue for a while. Nothing
major, just some sync-up with changes that already went into device code
(hard-coding desc err return values and lport renaming). Also fixup
port fowarding transitions prompted by some DSA discussions about how to
restore port state when port leaves bridge.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman [Thu, 26 Feb 2015 04:15:38 +0000 (20:15 -0800)]
rocker: put port in FORWADING state after leaving bridge
Cleanup the port forwarding state transitions for the cases when the port
joins or leaves a bridge, or is brought admin UP or DOWN. When port is
bridged, we can rely on bridge driver putting port in correct state using
STP callback into port driver, regardless if bridge is enabled for STP or not.
When port is not bridged, we can reuse some of the STP code to enabled or
disable forwarding depending on UP or DOWN.
Tested by trying all the transitions from bridge/not bridge, and UP/DOWN, and
verifying port is in the correct forwarding state after each transition.
Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman [Thu, 26 Feb 2015 04:15:37 +0000 (20:15 -0800)]
rocker: rename lport to pport
This is just a rename of physical ports from "lport" to "pport". Not a
functional change. OF-DPA uses logical ports (lport) for tunnels, but the
driver (and device) were using "lport" for physical ports. Renaming physical
ports references to "pport", freeing up "lport" for use later with tunnels.
Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman [Thu, 26 Feb 2015 04:15:36 +0000 (20:15 -0800)]
rocker: fix non-portable err return codes
The rocker device returns error codes if something goes wrong with descriptor
processing. Originally the device used standard errno codes for different
errors, but since those errno codes aren't portable across ARCHs, the device
now returns hard-coded error codes that stay constant across diff ARCHs. Fix
driver to use those same hard-coded values.
Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 25 Feb 2015 23:13:07 +0000 (18:13 -0500)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-02-24
This series contains updates to i40e and i40evf only, which bumps their
versions to i40e 1.2.9 and i40evf 1.2.3.
Paul fixes i40e_debug_aq() for big endian machines by adding the
appropriate LExx_TO_CPU wrappers.
Catherine adds a requested speed variable to the link_status to store the
last speeds we requested from the firmware and use the advertised speed
settings in get_settings in ethtool now that we have it. Due to the
new code addition, she also refactors get_settings to improve readability
and to accommodate some of the longer lines of code by adding two
functions i40e_get_settings_link_up() and i40e_get_settings_link_down().
Carolyn adds a struct to the VSI struct to keep track of RXNFC settings
done via ethtool. Adds more information to the interrupt vector
names, specifically to the VF misc vector name so that we can distinguish
between all the interrupts.
Ashish enables the i40evf driver to enable debug prints via ethtool.
Mitch updates i40e to enable packet split only when IOMMU is in use,
since it shows a distinct advantage over the single-buffer path
because it minimizes DMA mapping and unmapping. Also adds the receive
routine in use to the features log message to be able to print the
receive packet split status.
Greg adds the ability to get, set and commit permanently the NPAR
partition BW configuration through configfs. Enables an application
to query the i40e driver's private flags to get the status of NPAR
enablement via ethtool.
Neerav adds support for bridge offload ndo_ops getlink and setlink
to enable bridge hardware mode as per the mode set via IFLA_BRIDGE_MODE.
The support is only enabled in the case of a PF VSI and not available for
any other VSI type.
Kevin fixes i40e by ensuring the BUF and FLAG_RD flags are set for
indirect admin queue command.
Vasu updates the driver to setup FCoE netdev device type as "fcoe", so that
it shows up in sysfs as FCoE device.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Wed, 25 Feb 2015 07:02:02 +0000 (23:02 -0800)]
net: dsa: Introduce dsa_is_port_initialized
To avoid race conditions when using the ds->ports[] array,
we need to check if the accessed port has been initialized.
Introduce and use helper function dsa_is_port_initialized
for that purpose and use it where needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 25 Feb 2015 22:04:15 +0000 (17:04 -0500)]
Merge branch 'sf2_hwbridge'
Florian Fainelli says:
====================
net: dsa: integration with SWITCHDEV for HW bridging
This patch set provides the DSA and SWITCHDEV integration bits together and
modifies the bcm_sf2 driver accordingly such that it works properly with HW
bridging.
Changes in v3:
- add back the null pointer check in dsa_slave_br_port_mask from Guenter
- slightly rework patch 1 commit message not to mention the function name
we add in patch 2
Changes in v2:
- avoid a race condition in how DSA network devices are created, patch from
Guenter Roeck
- provide a consistent and work STP state once a port leaves the bridge
- retain a bridge device pointer to properly flag port/bridge membership
- properly flush the ARL (Address Resolution Logic) in bcm_sf2.c
- properly retain port membership when individually bringing devices up/down
while they are members of a bridge
We discussed on the mailing-list the possibility of standardizing a "fdb_flush"
operation for DSA switch drivers, looking at the Marvell and Broadcom switches,
I am not convinced this is practical or diserable as the terminologies vary
here, but there is nothing preventing us from doing it later.
Many thanks to Guenter and Andrew for both testing and providing feedback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 24 Feb 2015 21:15:34 +0000 (13:15 -0800)]
net: dsa: bcm_sf2: add HW bridging support
Implement the bridge join, leave and set_stp callbacks by making that
we do the following:
- when a port joins the bridge, all existing ports in the bridge get
their VLAN control register updated with that joining port
- the joining port is including all existing bridge ports in its own
VLAN control register
The leave operation is fairly similar, special care must be taken to
make sure that port leaving the bridging is not removing itself from its
own VLAN control register.
Since the various BR_* states apply directly to our HW semantics, we
just need to translate these constants into their corresponding HW
settings, and voila!
We make sure to trigger a fast-ageing process for ports that are
joining/leaving the bridge and transition from incompatible states, this
is equivalent to triggering an ARL flush for that port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 24 Feb 2015 21:15:33 +0000 (13:15 -0800)]
net: dsa: integrate with SWITCHDEV for HW bridging
In order to support bridging offloads in DSA switch drivers, select
NET_SWITCHDEV to get access to the port_stp_update and parent_get_id
NDOs that we are required to implement.
To facilitate the integratation at the DSA driver level, we implement 3
types of operations:
DSA will resolve which switch ports that are currently bridge port
members as some Switch hardware/drivers need to know about that to limit
the register programming to just the relevant registers (especially for
slow MDIO buses).
We also take care of setting the correct STP state when slave network
devices are brought up/down while being bridge members.
Finally, when a port is leaving the bridge, we make sure we set in
BR_STATE_FORWARDING state, otherwise the bridge layer would leave it
disabled as a result of having left the bridge.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Tue, 24 Feb 2015 21:15:32 +0000 (13:15 -0800)]
net: dsa: Ensure that port array elements are initialized before being used
A network device notifier can be called for one or more of the created
slave devices before all slave devices have been registered. This can
result in a mismatch between ds->phys_port_mask and the registered devices
by the time the call is made, and it can result in a slave device being
added to a bridge before its entry in ds->ports[] has been initialized.
Rework the initialization code to initialize entries in ds->ports[] in
dsa_slave_create. With this change, dsa_slave_create no longer needs
to return slave_dev but can return an error code instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Change-ID: I345d777e94abd0acffe6a28793f675d251a86299 Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Fri, 6 Feb 2015 08:52:20 +0000 (08:52 +0000)]
i40evf: Add more info to interrupt vector names
This patch adds the netdev name to the VF misc vector name. Without
this patch, all the interrupts show the same info, so it difficult to
distinguish them.
Change-ID: I247828697e1373ecfb5f8dc1bc9618e98a7f4942 Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Greg Rose [Fri, 6 Feb 2015 08:52:19 +0000 (08:52 +0000)]
i40e: Use ethtool private flags to display NPAR status
Allow an application to query the i40e driver's private flags to get the
status of NPAR enablement. This will be used by applications to determine
if there are NPAR specific features available.
Change-ID: Ia6d9477a48f9c4cb41ca022bd433f77da3f2146c Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kevin Scott [Fri, 6 Feb 2015 08:52:18 +0000 (08:52 +0000)]
i40e: Set FLAG_RD when sending buffer FW must read
Set FLAG_RD for send_driver_version AQ command.
Change-ID: I8253051eff85a1d4b5a4e12ce0395b65ceb91e62 Signed-off-by: Kevin Scott <kevin.c.scott@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Fri, 6 Feb 2015 08:52:17 +0000 (08:52 +0000)]
i40e: print Rx packet split status
Add the RX routine in use to the features log message.
Change-ID: Ifbbf28fb7f42b9a3d2828586488e9e6331107dd5 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Vasu Dev [Mon, 9 Feb 2015 18:00:30 +0000 (18:00 +0000)]
i40e: setup FCoE device type
Setup FCoE netdev device type as "fcoe", so that it shows up in
sysfs as FCoE device.
Change-ID: Ie13a1a332dba4d5802586926104ee01ef20da44f Signed-off-by: Vasu Dev <vasu.dev@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kevin Scott [Fri, 6 Feb 2015 08:52:15 +0000 (08:52 +0000)]
i40e: Set BUF flag for Set Version AQ command
BUF flag must be set for indirect AQ command.
Change-ID: I6819718a47baf69d1a91ebaed89f735ed6e86025 Signed-off-by: Kevin Scott <kevin.c.scott@intel.com> Acked-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Neerav Parikh [Fri, 6 Feb 2015 08:52:14 +0000 (08:52 +0000)]
i40e: Add support for getlink, setlink ndo ops
Add support for bridge offload ndo_ops getlink and setlink to
enable bridge hardware mode as per the mode set via IFLA_BRIDGE_MODE.
The support is only enabled in case of a PF VSI and not available for
any other VSI type.
By default the i40e driver inserts a bridge as part of the bring-up
when a FDIR type VSI and/or a FCoE VSI is created. This bridge is
created in VEB mode by default i.e. after creating the bridge using
"Add VEB" AQ command the loopback for the PF's default VSI is enabled.
The patch adds capability where all the VSIs created as downlink to
the bridge inherits the loopback property and enables loopback only
if the uplink bridge is operating in VEB mode.
Hence, there is no need to explicitly enable loopback as part of
allocating resources for SR-IOV VFs and call to do that has been
removed.
In case a user-request is made either via "bridge" utility or using
the bridge netlink interface that requires to change the hardware
bridge mode then that would require a PF reset and rebuild of the
switch hierarchy.
Also update the copyright year.
Change-ID: I4d78fc1c83158efda29ba7be92239b74f75d6d25 Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Tested-By: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Greg Rose [Fri, 6 Feb 2015 08:52:13 +0000 (08:52 +0000)]
i40e: Implement configfs for NPAR BW configuration
Add configfs controls to get, set and commit NPAR BW configurations.
We export three controls:
min_bw - Can take a value from 0 to 100 inclusive
max_bw - Can take a value from 1 to 100 inclusive
commit - A write-only control that accepts only a value of 1 and will
cause the BW settings to be permanently committed to NVM so
that they are persistent across power cycles and system
resets
The BW values are relative and are expressed as percentages. For more
information on the interpretation of the BW settings see the Dell
specifications for NPAR.
Also update the copyright year.
Change-ID: Id7496ca65630b5037e32ba6a5a748fbc1632881b Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Tested-By: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Greg Rose [Fri, 6 Feb 2015 08:52:12 +0000 (08:52 +0000)]
i40e: Add NPAR BW get and set functions
We need to be able to get, set and commit permanently the NPAR
partition BW configuration through configfs. These are necessary
precursor functions for that feature.
Also update the copyright year.
Change-ID: I9d5ca160a9288145f1dd2042994028679fff55f3 Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Fri, 6 Feb 2015 08:52:11 +0000 (08:52 +0000)]
i40e: enable packet split only when IOMMU present
When an IOMMU is in use, the packet split receive path shows a distinct
advantage over the single-buffer path because it minimizes DMA mapping
and unmapping. However, this is not an advantage for systems with no
IOMMU. At init time, check to see if an IOMMU is enabled and enable
packet split receives.
Change-ID: I4f70d2e9c31bbea3dc8fd0c5734959a6e6602210 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ashish Shah [Fri, 6 Feb 2015 08:52:10 +0000 (08:52 +0000)]
i40evf: allow enabling of debug prints via ethtool
Copy setting from ethtool to the HW specific struct to actually
enable prints. Change print from i40e to i40evf to differentiate
drivers in bare metal scenarios.
Also update the copyright year.
Change-ID: I06fee26247299a08f2e1c70fc811a9ea0931c4dd Signed-off-by: Ashish Shah <ashish.n.shah@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Fri, 6 Feb 2015 08:52:09 +0000 (08:52 +0000)]
i40e: Add method to keep track of current rxnfc settings
This patch adds a struct to the VSI struct to keep track of rxnfc
settings done via ethtool. Without this patch, the device can only
list the options available, not the current settings and this is not
clear to the user. Without current settings, the available settings
never changing looks like a bug.
Also update the copyright year.
Change-ID: I087bbfdb33b330496a671630a7586773e3b3e589 Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e/i40evf: Use advertised speed settings in ethtool and refactor get_settings
Add a requested speed variable to the link_status struct to store the
last speeds we requested from the firmware (the speeds the FW will be
advertising with if autoneg is enabled).
Use the advertised speed settings in get_settings in ethtool now that
we have it. Also set the requested speed settings in set_settings in
ethtool as they are requested and initialize them in probe based on what
the firmware remembers as the last requested speeds.
To accommodate some longer lines in this new code, and improve
readability I have added two functions i40e_get_settings_link_up
and i40e_get_settings_link_down which get_settings now calls first.
It then does all of the settings that happen regardless of link
state. Some PHY types that supported the same settings were also combined.
Also update the copyright year.
Change-ID: Ica0c5ac81b6069ea6a7406fce7482f7816d4455c Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e/i40evf: Fix output of i40e_debug_aq() for big endian machines
The function i40e_debug_aq() prints information helpful in debugging
admin queue commands, but it doesn't do so correctly on big endian machines.
This patch adds the appropriate LExx_TO_CPU wrappers for big endian
architectures.
Also update the copyright year.
Change-ID: I4b2dc229ed5bf6dfe35632a58cddf53c21aff4b0 Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tino Reichardt [Tue, 24 Feb 2015 18:28:01 +0000 (10:28 -0800)]
net: via-rhine: add BQL support
Add Byte Queue Limits (BQL) support to via-rhine driver.
[edumazet] tweaked patch and changed TX_RING_SIZE from 16 to 64
Signed-off-by: Tino Reichardt <milky-kernel@mcmilk.de> Tested-by: Jamie Gloudon <jamie.gloudon@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 24 Feb 2015 21:05:54 +0000 (16:05 -0500)]
Merge branch 'bonding-next'
Mahesh Bandewar says:
====================
(Shortened) Bonding patch series
I'm shortening the earlier patch series to just two patches at this moment.
Andy is going to integrate remaining 3 patches with his netlink changes
and post the completed patches.
These two patches are the same one from the previous patch series with
some styling changes (Dave Miller's suggestions) for the churn-machine patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar [Tue, 24 Feb 2015 01:50:11 +0000 (17:50 -0800)]
bonding: Implement port churn-machine (AD standard 43.4.17).
The Churn Detection machines detect the situation where a port is operable,
but the Actor and Partner have not attached the link to an Aggregator and
brought the link into operation within a bound time period. Under normal
operation of the LACP, agreement between Actor and Partner should be reached
very rapidly. Continued failure to reach agreement can be symptomatic of
device failure.
Actor-churn-detection state-machine Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
===================================
Mahesh Bandewar [Tue, 24 Feb 2015 01:50:10 +0000 (17:50 -0800)]
bonding: Verify RX LACPDU has proper dest mac-addr
The 802.1AX standard states:
"The DA in LACPDUs is the Slow_Protocols_Multicast address."
This patch enforces that and drops LACPDUs with destination MAC
addresses other than Slow_Protocols_Multicast address
Signed-off-by: Mahesh Bandewar <maheshb@google.com> Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 24 Feb 2015 16:48:48 +0000 (11:48 -0500)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-02-23
This series contains updates to e1000e, igbvf, i40e and i40evf.
David adds support for i219 devices to the e1000e driver.
Jeff (me) provides two patches to cleanup igbvf, first cleans up the
whitespace issues found and the second cleans up the usage of msleep(),
min() and max() with usleep_range(), min_t() and max_t() respectively.
Kamil updates the shadow RAM read/write functions by refactoring them
to prepare for future work.
Shannon renames the debugfs command "clear_stats pf" to clear_stats port"
to clarify what the function really does.
Mitch refactors the receive routine, by splitting the receive hot path
code into two, one for packet split and one for single buffer, which
improves receive performance. Disables NAPI polling sooner when closing
the interface to fix an occasional panic during close which was
caused by the driver trying to delete and clean rings at the same time.
Also refactors reset for i40evf, since a recent change to the shutdown
flow messed up the reset flow. Since i40evf_down() now holds the
critical section lock, we cannot call it from the reset handler, which
also holds the lock.
Nicholas restricts the virtual channel opcodes should remain consistent
between updates to the opcode enum.
Neerav converts the VSI connection type to use a #define instead of
using a magic number.
Anjali updates the registers file to remove registers no longer available.
Also fixes the EMPR interrupt handling, so that we won't trigger another
EMPR when we receive an EMPR event.
Catherine cleans up the variable an_enable since it was set and never
used.
Greg fixes the netdev op that allows the operator to turn MAC/VLAN
spoof checking on and off so that it includes the flag for VLAN spoof
checking.
v2: Updated patch #10 in the series to use test_and_clear_bit() as
suggested by Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petri Gynther [Mon, 23 Feb 2015 19:00:46 +0000 (11:00 -0800)]
net: bcmgenet: rename bcmgenet_hw_params->bds_cnt and GENET_DEFAULT_BD_CNT
bcmgenet_hw_params->bds_cnt and GENET_DEFAULT_BD_CNT are used only in Tx init.
Rename them accordingly:
- bcmgenet_hw_params->bds_cnt => bcmgenet_hw_params->tx_bds_per_q
- GENET_DEFAULT_BD_CNT => GENET_Q16_TX_BD_CNT
Signed-off-by: Petri Gynther <pgynther@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petri Gynther [Mon, 23 Feb 2015 19:00:45 +0000 (11:00 -0800)]
net: bcmgenet: precalculate TxCB->bd_addr
There is 1-to-1 mapping between TxCBs and TxBDs. Precalculate TxCB->bd_addr
once in bcmgenet_init_dma() instead of doing it over and over needlessly in
bcmgenet_get_txcb().
Signed-off-by: Petri Gynther <pgynther@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petri Gynther [Mon, 23 Feb 2015 19:00:45 +0000 (11:00 -0800)]
net: bcmgenet: bcmgenet_init_tx_ring() cleanup
1. Simplify function description
2. Rename function parameter write_ptr to start_ptr to better indicate use
3. Remove unnecessary local variable first_bd
4. Remove out-of-place comment "Unclassified traffic goes to ring 16"
5. Fix TDMA_WRITE_PTR register init
Signed-off-by: Petri Gynther <pgynther@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 24 Feb 2015 02:32:59 +0000 (02:32 +0000)]
samples/pktgen: Use bash as interpreter
These scripts use the non-POSIX 'function' and 'local' keywords so
they won't work with every /bin/sh. We could drop 'function' as it is
a no-op, but 'local' makes for cleaner scripts. Require use of bash.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 24 Feb 2015 02:32:37 +0000 (02:32 +0000)]
samples/pktgen: Correct comments about the thread config
They all claimed to be two CPU examples using eth1, eth2 but
that is only true in one case!
Rob Jones pointed out spelling and grammar errors here, which I've
also corrected.
Cc: Rob Jones <rob.jones@codethink.co.uk> Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 24 Feb 2015 02:32:07 +0000 (02:32 +0000)]
samples/pktgen: Add sample scripts for pktgen facility
These are Robert Olsson's samples which used to be available from
<ftp://robur.slu.se/pub/Linux/net-development/pktgen-testing/examples/>
but currently are not.
Change the documentation to refer to these consistently as 'sample
scripts', matching the directory name used here.
Cc: Robert Olsson <robert@herjulf.se> Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 24 Feb 2015 02:31:52 +0000 (02:31 +0000)]
pktgen: Fix grammar errors and some poor wording in documentation
Thanks to Rob Jones for suggesting some of the changes.
Cc: Rob Jones <rob.jones@codethink.co.uk> Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Mitch Williams [Thu, 29 Jan 2015 07:17:20 +0000 (07:17 +0000)]
i40evf: don't wait forever
Under rare circumstances, after a reset, set_rx_mode might get called
while the watchdog is running, which will cause a deadlock on the
critical section lock. To correct this, add a counter and give up trying
to get the lock after fifty tries. Log a message if this happens but
don't take any other action. Because this happens after a reset, all of
the Rx filters are still in place and the device won't lose
connectivity.
We can also get stuck during shutdown, if the PF has stopped communicating
with us, or if a reset is occurring. If we can't get the lock after a reasonable
amount of time, just error out. Something else bad is happening anyway, so
adding this filter is the least of our concern right now.
Change-ID: I159731e2a82a06b389ee31b34ce336548e05baa0 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Thu, 29 Jan 2015 07:17:19 +0000 (07:17 +0000)]
i40evf: refactor reset
A recent change to the shutdown flow messed up the reset flow. Since
i40evf_down now holds the critical section lock, we cannot call it from
the reset handler, which also holds the lock. To do so causes a deadlock
accompanied by wailing and gnashing of teeth. This is easily triggered
by running an ethtool self-test on the PF device.
Instead, we move the relevant portions of i40evf_down into the reset
handler and bend them to our will. Additionally, we can optimize the
reinit path by not deleting the MAC and VLAN filters and then adding
them back again. Instead, we just set the 'add' flag and let the
watchdog resynchronize the filter list with the PF driver. We also
reword a few messages to make them more consistent with the rest of the
driver.
Change-ID: I03dd92ae736f7719fca3564b12a2cf9b98c6cb18 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Thu, 29 Jan 2015 07:17:18 +0000 (07:17 +0000)]
i40evf: disable NAPI polling sooner
When closing the interface, disable NAPI polling before any other
activities. This fixes an occasional panic during close caused by the
driver trying to delete and clean rings at the same time.
Change-ID: Ib4d427b13d310258ea85b248d535da70ecf0c1e9 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Greg Rose [Thu, 29 Jan 2015 07:17:17 +0000 (07:17 +0000)]
i40e: Fix i40e_ndo_set_vf_spoofchk
The netdev op that allows the operator to turn MAC/VLAN spoof checking on
and off did not include the flag for VLAN spoof checking. This patch
fixes that problem.
Change-ID: Ib4c9e639024a854592d97af22706544881ac3fcb Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change-ID: I64f47c3367ea8ff2a53068e895d7a1f60726c871 Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e/i40evf: Remove unused variable an_enable and function update_link_info
An_enable was never used only set so lets remove it. The function
update_link_info only did two things, call get_link_info and set
an_enabled. Therefore we should also remove update_link_info and
change all references to it to get_link_info.
Change-ID: Ie3022680fa7a94bfd495a4f5fc76a73701d85569 Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We shouldn't trigger another EMPR when we receive an EMPR event.
This patch handles EMPR event reception with a different state
so that we can do the right thing for NVM.
Change-ID: I9cac70b3658600f016a65beb6fb157e1c1f9adf9 Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some registers have been removed so take them out and
stop updating and looking at them.
Change-ID: I33da922c8de993a94dd8b8d8a2ae2146b8ca1a27 Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Neerav Parikh [Sat, 24 Jan 2015 09:58:38 +0000 (09:58 +0000)]
i40e: Use #define for the VSI connection type
Use #defined VSI connection type values instead of using magic numbers.
Change-ID: I2f6cf7bf394d391e1c0fe61779e9e4ad8858154a Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Nicholas Nunley [Sat, 24 Jan 2015 09:58:37 +0000 (09:58 +0000)]
i40e/i40evf: restrict VC opcodes to their initial values
Until the time a more robust versioning scheme is needed/implemented all
established virtual channel opcode values should remain consistent between
updates to the opcode enum.
This patch repositions I40E_VIRTCHNL_OP_CONFIG_RSS to the end of the enum. In
its current position this opcode displaces the initial value of
I40E_VIRTCHNL_OP_EVENT and will cause PF/VF compatibility issues.
Going forward the expectation is either:
a) All future opcode additions will be added as the last element of the
enum. Once VF drivers start making use of the new commands the virtual
channel version will need to be incremented and drivers will need to
implement a simple version check whereby VF drivers can only load on
PFs with a >= version.
b) or, if needed, design and implement a more complicated API
negotiation capability.
In either case PF drivers should always maintain backwards compatibility with
earlier VF driver versions.
Change-ID: Ie245daa09a231b6680ed793d648bdcc76caefe58 Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Sat, 24 Jan 2015 09:58:35 +0000 (09:58 +0000)]
i40e/i40evf: Refactor the receive routines
Split the receive hot path code into two, one for packet split and one
for single buffer. This improves receive performance since we only need
to check if the ring is in packet split mode once per NAPI poll time,
not several times per packet. The single buffer code is further improved
by the removal of a bunch of code and several variables that are not
needed. On a receive-oriented test this can improve single-threaded
throughput.
Also refactor the packet split receive path to use a fixed buffer for
headers, like ixgbe does. This vastly reduces the number of DMA mappings
and unmappings we need to do, allowing for much better performance in
the presence of an IOMMU.
Lastly, correct packet split descriptor types now that we are actually
using them.
Change-ID: I3a194a93af3d2c31e77ff17644ac7376da6f3e4b Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Sat, 24 Jan 2015 09:58:34 +0000 (09:58 +0000)]
i40e: rename debugfs clear_stats option
Change debugfs command from "clear_stats pf" to "clear_stats port"
to be clearer what the action is. Also, limit the action to the
base PF, not the NPAR partitions.
Change-ID: I22aa39c0962d83a83a985097b1000ed7f8c66f3f Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kamil Krawczyk [Sat, 24 Jan 2015 09:58:33 +0000 (09:58 +0000)]
i40e: update Shadow RAM read/write functions
This change is to refactor the read/write functions to support
future work.
Change-ID: I13150d5e3042f2c617362c0140dc7e6473ebcdee Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com> Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher [Wed, 21 Jan 2015 09:57:50 +0000 (09:57 +0000)]
igbvf: Fix code comments and whitespace
Fix the code comments to align with the drivers/net/ commenting style.
Also fix other checkpatch errors such as using tabs where possible and
properly wrap lines to conform to the 80 char limit (unless it is
a string).
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com>
David Ertman [Tue, 10 Feb 2015 09:10:43 +0000 (09:10 +0000)]
e1000e: initial support for i219
i219 is the next-generation LOM that will be available on systems with the
Sunrise Point Platform Controller Hub (PCH) chipset from Intel. This patch
provides the initial support for the device.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Tested-by: Carmen Edwards <carmenx.edwards@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Mon, 23 Feb 2015 20:08:37 +0000 (15:08 -0500)]
Merge branch 'be2net-next'
Sathya Perla says:
====================
be2net: patch set
Hi Dave, the following patch set reduces code duplication
in probe/pci-resume/eeh-resume and remove/pci-suspend/eeh-error and UE-error
detect/recovery paths. New helper routines have been introduced for this
purpose. Pls apply this set to the net-next tree. Thanks!
Patch 1 refactors the alloc/free code of adapter struct's fields into
a new set of helper routines -- be_drv_init/cleanup().
Patch 2 gets rid of the be_get_initial_config() routine as be_get_config()
is the place holder for related code.
Patch 3 introduces a new helper routine be_func_init() to execute the
initialization code used in probe/pci-resume/eeh-resume to remove
code duplication.
Patch 4 introduces a wrapper for scheduling/canceling error detection
task on similar lines to the be_worker task.
Patch 5 refactors UE error detection and recovery code on similar lines
to EEH code. Cleaning up resources is done in the error detection routine
followed by error recovery.
Patch 6 gets rid of the lancer_test_and_set_rdy_state() routine as the
same code now available in be_func_init().
Patch 7 creates a new helper routine be_resume() for all the common code
in be_probe(), be_pci_resume() and be_eeh_resume(), to reduce code duplication.
Patch 8 creates a new helper routine be_cleanup() for all the common
cleanup code duplicated in the suspend/EEH err detection paths.
Patch 9 moves be_func_init() inside be_setup() as everytime be_setup()
is called, the driver will have to wait for the function/FW to be be
initialized.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Every time be_setup() is called, the driver will have to wait for the
function/FW to be properly initialized. So, it make sense to move this call
inside be_setup().
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh AP [Mon, 23 Feb 2015 09:20:15 +0000 (04:20 -0500)]
be2net: refactor adapter resource cleanup sequence into be_cleanup()
Most of the resource cleanup sequences performed in be_suspend(),
be_eeh_err_detected() and be_err_detection_task() are same. Moved the
common code to a new routine be_cleanup() to avoid code duplication.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh AP [Mon, 23 Feb 2015 09:20:14 +0000 (04:20 -0500)]
be2net: refactor adapter resource initialzation sequence into be_resume()
Most of the adapter initialisation sequences performed in be_resume(),
be_eeh_resume() and be_err_recover() are same. Renamed be_resume() to
be_pci_resume() and moved the common code to a new routine be_resume() to
avoid code duplication.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Mon, 23 Feb 2015 09:20:13 +0000 (04:20 -0500)]
be2net: remove code duplication relating to Lancer reset sequence
The steps needed for Lancer's reset/initialization sequence are:
a) wait for SLIPORT_STAUS RDY bit to be set
b) set the SLIPORT_CONTROL IP bit
c) repeat step "a"
The code needed for this sequence is already covered by the be_func_init()
routine (with minor modifications.) So, get rid of the
lancer_test_and_set_rdy_state() and lancer_provisioning_error() routines
that unnecessarily duplicate this code. Also fixed the error recovery
function to take care of these changes
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh AP [Mon, 23 Feb 2015 09:20:12 +0000 (04:20 -0500)]
be2net: refactor error detect/recovery function
Currently when an error is detected, the queue resources are being cleaned up
in the recovery routine. The resources are better cleaned up in the error
detection routine itself (similar to EEH code.)
So, this patch re-factors error processing logic to follow the following sequence:
- check if there is an error in adapter
- if error,
- cleanup resources
- attempt recovery
The patch renames lancer_recover_func() to be_err_recover() as this
routine will be used in the future for error recovery on Skyhawk too.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Mon, 23 Feb 2015 09:20:11 +0000 (04:20 -0500)]
be2net: use a wrapper to schedule and cancel error detection task
Also rename func_recovery_work/task to err_detection_work/task as error
detection is the primary goal of this task while recovery is not guaranteed.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Mon, 23 Feb 2015 09:20:10 +0000 (04:20 -0500)]
be2net: refactor function initalization sequence into be_func_init()
Function initialization sequence is executed in be_probe(), be_resume
and be_eeh_resume(). Move this code to a new routine called be_func_init()
to prevent code duplication.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Mon, 23 Feb 2015 09:20:09 +0000 (04:20 -0500)]
be2net: get rid of be_get_initial_config() call from be_probe()
Most of the code to fetch the adapter state is in be_setup()->be_get_config().
So, move the code from be_get_initial_config() to be_get_config().
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Mon, 23 Feb 2015 09:20:08 +0000 (04:20 -0500)]
be2net: move adapter fields alloc/free code to new routines
The members of be_adapter struct were being allocated in two separate
routines -- be_ctrl_init() and be_stats_init(). Also, some other members
were allocated elsewhere. This patch moves the alloc/free code into
be_drv_init/cleanup() routines. The be_pci_map_bars() routine that was
called from be_ctrl_init() is now called directly from be_probe().
The new routine be_drv_init() will now be the place-holder for allocating
memory for any new be_adapter{} members in the future.
Some routines needed to be moved to provide forward definitions for their
calls.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu [Sun, 22 Feb 2015 04:21:51 +0000 (20:21 -0800)]
bridge: add vlan info to bridge setlink and dellink notification messages
vlan add/deletes are not notified to userspace today. This patch adds
vlan info to bridge newlink/dellink notifications generated from the
bridge driver. Notifications use the RTEXT_FILTER_BRVLAN_COMPRESSED
flag to compress vlans into ranges whereever applicable.
The size calculations does not take ranges into account for
simplicity. This has the potential for allocating a larger skb than
required.
There is an existing inconsistency with bridge NEWLINK and DELLINK
change notifications. Both generate NEWLINK notifications. Since its
always a NEWLINK notification, this patch includes all vlans the port
belongs to in the notification. The NEWLINK and DELLINK request
messages however only include the vlans to be added and deleted.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Sun, 22 Feb 2015 21:47:56 +0000 (13:47 -0800)]
batman-adv: Fix use of seq_has_overflowed()
net-next commit 6d91147d183c ("batman-adv: Remove uses of return value
of seq_printf") incorrectly changed the overflow occurred return from
-1 to 1. Change it back so that the test of batadv_write_buffer_text's
return value in batadv_gw_client_seq_print_text works properly.
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bojan Prtvar [Sun, 22 Feb 2015 10:46:35 +0000 (11:46 +0100)]
net: Remove state argument from skb_find_text()
Although it is clear that textsearch state is intentionally passed to
skb_find_text() as uninitialized argument, it was never used by the
callers. Therefore, we can simplify skb_find_text() by making it
local variable.
Signed-off-by: Bojan Prtvar <prtvar.b@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log