Hi,
This is a patch to incorporate comments from earlier 12 patches.
It also fixes a few issues we found during this time.
Following is a list of changes in this patch. Item 1 incorporates
earlier comments. Issues addressed in items 2 to 4 were discovered
recently.
1. wmb() call in s2io_xmit() replaced with mmiowb().
2. The dtx_control register was earlier programmed incorrectly
for Xframe II adapter.
3. As suggested by hardware team, after a reset, in case of
Xframe II adapter, we clear certain spurious errors by
clearing PCI-X ECC status register, "detected parity error"
bit in PCI_STATUS register and PCI_STATUS bit in txpic_int register.
4. On IBM PPC platforms, we found that in the Rx buffer replenish
function, two memory writes(one to the the descriptor length and
another to the ownership) were getting reordered. This was causing
the adapter to see the ownership transfered to it before the length
was updated.
One solution was to add a wmb() but since this would turnout expensive
on some platforms if called for every descriptor, we set the ownership
bit and other fields of '2' to 'N' Rx descriptors followed by a wmb()
and then set the ownership of first descriptor ('1').
Here the value 'N' is configurable by making it a module loadable
parameter (rxsync_frequency).
(NOTE: This parameter is a power of 2).
5. Bumped up the driver version no. to 2.0.2.1
Hi,
The last patch in this series fixes the following issues found during
testing.
1. Ensure we don't pass zero sized buffers to the card(which can lockup)
2. Restore the PCI-X parameters(in case of Xframe I adapter) after a reset.
3. Make sure total size of all FIFOs does not exceed 8192.
[PATCH] S2io: New link handling scheme for Xframe II
Hi,
The below patch implements a new "Link state change handling"
scheme supported by the Xframe II adapter. It also bumps up the
driver version to 2.0.2.0.
Hi,
This is a patch to provide bimodal interrupt moderation support for
Xframe II adapter. Basically, in this moderation scheme, the adapter
raises a traffic interrupt if the no. of packets transmitted and/or
received reaches a programmable threshold.
Hi,
This patch provides basic support for the Xframe II adapter.
Includes the following changes:
1. New values to program XAUI interface.
2. Print the PCI/PCI-X mode(bus frequency, width).
3. Remove EOI from reset during intialization.
4. Enable all 8 PCCs if Xframe II adapter.
5. Programs the RLDRAM size depending on the device.
(Note: RLDRAM size on XFARME-I is 64Mb whereas on XFRAME-II it's 32 Mb).
6. Enable extended(64-bit) statistics counters.
7. Program timer interrupt duration based on PCI/PCI-X clock speed.
8. Not required to save/restore PCI config space before/after reset.
Hi,
This patch implements the slow-path handling functions(link
state change, hardware errors) as a timer. It is not
handled in interrupt handler as was done previously.
Hi,
This patch relates to mostly performance related changes.
1. Fixed incorrect computation of PANIC level in rx_buffer_level().
2. Removed unnecessary PIOs(read/write of tx_traffic_int and
rx_traffic_int) from interrupt handler and removed read of
general_int_status register from xmit routine.
3. Enable two-buffer mode(for Rx path) automatically for SGI
systems. This improves Rx performance dramatically on
SGI systems.
Hi,
Below patch includes fixes for few purely software bugs identified
since last release.
1. Keep track and display(as part of ethtool command output) the no.
of single-bit and double-bit ECC errors.
2. Handle race condition between intr handler and "interface down"
routine.
3. Initial link state setting modified so that the link state displayed
after "interface Up" is correct.
4. Fix for "Incorrect Tx packet count when TSO is enabled".
5. Disable periodic DMA of statistics and schedule one-shot DMA
only when required.
Hi,
Below patch addresses few h/w specific issues.
1. Check for additional ownership bit on Rx path before
starting Rx processing.
2. Enable only 4 PCCs(Per Context Controller) for Xframe I
revisions less than 4.
3. Program Rx and Tx round robin registers depending on
no. of rings/FIFOs.
4. Tx continous interrupts is now a loadable parameter.
5. Reset the card if we get double-bit ECC errors.
6. A soft reset of XGXS being done to force a link state change has been
eliminated.
7. After a reset, clear "parity error detected" bit,
PCI-X ECC status register, and PCI_STATUS bit in
tx_pic_int register.
8. The error in the disabling allmulticast implementation has been
rectified.
9. Leave the PCI-X parameters MMRBC, OST etc. at their
BIOS/system defaults.
Hi,
We are submitting a series of 13 patches to support our Xframe I and
Xframe II line of products. The patches can be categorized as follows:
Patches 1-8 : Changes applicable to both Xframe I and II
Patches 9-11: Xframe II specific features
Patch 12: Addresses issues found during testing cycle.
Patch 13: Incorpoates mostly the review comments from community
and some last moment bug fixes.
Please review the patches and let us know your comments.
Starting with patch 1 below.
This patch involves cosmetic changes(tabs and indentation,
regrouping of transmit and receive data structures, typecasting,
code cleanup).
James Bottomley [Wed, 10 Aug 2005 18:29:15 +0000 (11:29 -0700)]
[PATCH] remove name length check in a workqueue
We have a chek in there to make sure that the name won't overflow
task_struct.comm[], but it's triggering for scsi with lots of HBAs, only
scsi is using single-threaded workqueues which don't append the "/%d"
anyway.
All too hard. Just kill the BUG_ON.
Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org>
[ kthread_create() uses vsnprintf() and limits the thing, so no
actual overflow can actually happen regardless ]
[PATCH] ppc64: Fix Fan control for new PowerMac G5 2.7GHz machines
The workaround for broken device-tree that prevents fan control from
working on recent G5 models need to be "enabled" for machines with
revision 0x37 of the bridge in addition to machines with revision 0x35.
Alexander Nyberg [Wed, 10 Aug 2005 17:11:36 +0000 (10:11 -0700)]
[PATCH] ns558 list handling fix
Need to use list_for_entry_safe(), as we're removing items during the
traversal. list_for_each_entry() uses the first ptr also as an iterator, if
you kfree() it slab takes it, might poison it and then you try to use it to
iterate to the next object in list.
Fix the p-persistence CSMA algorithm which in simplex mode was starting
with a slottime delay before doing anything else as if there was carrier
collision resulting in bad performance on simplex links.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org> Acked-by: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tejun Heo [Sun, 7 Aug 2005 05:53:40 +0000 (14:53 +0900)]
[PATCH] sata: fix sata_sx4 dma_prep to not use sg->length
sata_sx4 directly references sg->length to calculate total_len in
pdc20621_dma_prep(). This is incorrect as dma_map_sg() could have
merged multiple sg's into one and, in such case, sg->length doesn't
reflect true size of the entry. This patch makes it use
sg_dma_len(sg).
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Ben Dooks [Wed, 10 Aug 2005 15:45:14 +0000 (16:45 +0100)]
[PATCH] ARM: 2849/1: S3C24XX - USB host update (2848/1)
Patch from Ben Dooks
Rename the s3c2410_report_oc() to s3c2410_usb_report_oc()
as this is an usb specific function.
Change port power on the usb-simtec implementation to only
power up the output if both are set, as per the usb 1.1
specification
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Wed, 10 Aug 2005 15:18:35 +0000 (16:18 +0100)]
[ARM] Control v6 'global' bit via Linux PTE entries
Unfortunately, we can't use the "user" bit in the page tables to
control whether a page table entry is "global" or "asid" specific,
since the vector page is mapped as "user" accessible but is not
process specific.
Therefore, give direct control of the ARMv6 "nG" (not global)
bit to the mm layers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Markus Lidel [Tue, 9 Aug 2005 21:30:57 +0000 (14:30 -0700)]
[PATCH] I2O: added pci_request_regions() before using the controller
Added pci_request_regions() before using the controller to avoid duplicate
usage of the I2O controller when the dpt_i2o driver and I2O subsystem is
loaded at the same time.
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com> Cc: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Markus Lidel [Tue, 9 Aug 2005 17:08:03 +0000 (10:08 -0700)]
[PATCH] i2o: remove new configuration API
Remove new configuration API from i2o_config
The API-patch is still available from the I2O website (which is mentioned in
the kernel config now). It is removed because it creates a new binary
sysfs-attribute, which doesn't have the limitiation of 4k. Expect for the
Adaptec controllers, which has a limitation in the hardware this attribute
doesn't make sense anywhere else. Until the sysfs API provides an attribute
which doesn't buffer (like firmware) and let access to at least 64k blocks i
provide a separate patch...
(akpm: basically, this API was introduced post-2.6.12 and Markus wants to pull
it out before 2.6.13).
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Tue, 9 Aug 2005 17:07:59 +0000 (10:07 -0700)]
[PATCH] cpuset release ABBA deadlock fix
Fix possible cpuset_sem ABBA deadlock if 'notify_on_release' set.
For a particular usage pattern, creating and destroying cpusets fairly
frequently using notify_on_release, on a very large system, this deadlock
can be seen every few days. If you are not using the cpuset
notify_on_release feature, you will never see this deadlock.
The existing code, on task exit (or cpuset deletion) did:
get cpuset_sem
if cpuset marked notify_on_release and is ready to release:
compute cpuset path relative to /dev/cpuset mount point
call_usermodehelper() forks /sbin/cpuset_release_agent with path
drop cpuset_sem
Unfortunately, the fork in call_usermodehelper can allocate memory, and
allocating memory can require cpuset_sem, if the mems_generation values
changed in the interim. This results in an ABBA deadlock, trying to obtain
cpuset_sem when it is already held by the current task.
To fix this, I put the cpuset path (which must be computed while holding
cpuset_sem) in a temporary buffer, to be used in the call_usermodehelper
call of /sbin/cpuset_release_agent only _after_ dropping cpuset_sem.
So the new logic is:
get cpuset_sem
if cpuset marked notify_on_release and is ready to release:
compute cpuset path relative to /dev/cpuset mount point
stash path in kmalloc'd buffer
drop cpuset_sem
call_usermodehelper() forks /sbin/cpuset_release_agent with path
free path
The sharp eyed reader might notice that this patch does not contain any
calls to kmalloc. The existing code in the check_for_release() routine was
already kmalloc'ing a buffer to hold the cpuset path. In the old code, it
just held the buffer for a few lines, over the cpuset_release_agent() call
that in turn invoked call_usermodehelper(). In the new code, with the
application of this patch, it returns that buffer via the new char
**ppathbuf parameter, for later use and freeing in cpuset_release_agent(),
which is called after cpuset_sem is dropped. Whereas the old code has just
one call to cpuset_release_agent(), right in the check_for_release()
routine, the new code has three calls to cpuset_release_agent(), from the
various places that a cpuset can be released.
This patch has been build and booted on SN2, and passed a stress test that
previously hit the deadlock within a few seconds.
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] i8xx_tco.c: arm watchdog only when started
i8xx_tco.c v0.08: only "arm" the watchdog when the watchdog has been
started. (Kernel Bug 4251: system reset when battery is read and i8xx_tco
driver loaded)
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
default_idle() is looking at new variable can_do_pal_halt. However,
that variable did not get cleared upon "nohalt" boot option. Result
is that "nohalt" option is ignored until perfmon is exercised.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Kumar Gala [Mon, 8 Aug 2005 21:49:17 +0000 (14:49 -0700)]
[PATCH] ppc32: Fix MPC834x USB memory map offsets
The memory mappings for MPC8349 USB MPH and DR modules were reversed.
Signed-off-by: Li Yang <LeoLi@freescale.com> Signed-off-by: Jiang Bo <Tanya.jiang@freescale.com> Signed-off-by: Kumar Gala <kumar.gala@freescale.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[SCSI] fix target scanning oops with fc transport class
We have some nasty issues with 2.6.12-rc6. Any request to scan on
the lpfc or qla2xxx FC adapters will oops. What is happening is the
system is defaulting to non-transport registered targets, which
inherit the parent of the scan. On this second scan, performed by
the attribute, the parent becomes the shost instead of the rport.
The slave functions in the 2 FC adapters use starget_to_rport()
routines, which incorrectly map the shost as an rport pointer.
Additionally, this pointed out other weaknesses:
- If the target structure is torn down outside of the transport,
we have no method for it to be regenerated at the proper parent.
- We have race conditions on the target being allocated by both
the midlayer scan (parent=shost) and by the fc transport
(parent=rport).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
John McCutchan [Mon, 8 Aug 2005 17:52:16 +0000 (13:52 -0400)]
[PATCH] fsnotify_name/inoderemove
The patch below unhooks fsnotify from vfs_unlink & vfs_rmdir. It
introduces two new fsnotify calls, that are hooked in at the dcache
level. This not only more closely matches how the VFS layer works, it
also avoids the problem with locking and inode lifetimes.
The two functions are
- fsnotify_nameremove -- called when a directory entry is going away.
It notifies the PARENT of the deletion. This is called from
d_delete().
- inoderemove -- called when the files inode itself is going away. It
notifies the inode that is being deleted. This is called from
dentry_iput().
Signed-off-by: John McCutchan <ttb@tentacle.dhs.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Michael Krufky [Mon, 8 Aug 2005 16:22:43 +0000 (09:22 -0700)]
[PATCH] dvb: lgdt330x frontend: some bug fixes & add lgdt3303 support
- Structural changes within lgdt330x driver, framework now supports
both chips... tested OK on lgdt3302 and lgdt3303.
- Add LG/TUA6034 dvb_pll_desc for ATSC with LG TDVS-H062F & DViCO FusionHDTV5.
- Fixed LGDT330X signal strength: For now, always set it to 0.
- Corrected LGDT330X boundary condition error in read_snr: dB calculation.
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net> Signed-off-by: Michael Krufky <mkrufky@m1k.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Harald Welte [Mon, 8 Aug 2005 09:50:55 +0000 (11:50 +0200)]
[PATCH] don't try to do any NAT on untracked connections
With the introduction of 'rustynat' in 2.6.11, the old tricks of preventing
NAT of 'untracked' connections (e.g. NOTRACK target in 'raw' table) are no
longer sufficient.
The ip_conntrack_untracked.status |= IPS_NAT_DONE_MASK effectively
prevents iteration of the 'nat' table, but doesn't prevent nat_packet()
to be executed. Since nr_manips is gone in 'rustynat', nat_packet() now
implicitly thinks that it has to do NAT on the packet.
This patch fixes that problem by explicitly checking for
ip_conntrack_untracked in ip_nat_fn().
Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ivan Kokshaysky [Mon, 8 Aug 2005 08:55:54 +0000 (12:55 +0400)]
[PATCH] VIA VT8235 PCI quirk
Like many other southbridges from different manufacturers, VIA VT8235
chip has two non-standard BARs for power management and SMBus registers
(see the datasheet at http://www.via.com.tw).
This new quirk routine fixes boot problem with 2.6.13-rc2/rc6 kernels on
Targa Visionary 811 Athlon64 laptop, as reported by Mikael Pettersson
<mikpe@csd.uu.se>.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Antonino Daplas [Mon, 8 Aug 2005 06:22:43 +0000 (14:22 +0800)]
[PATCH] nvidiafb: Fix initial display corruption on certain laptops
Reported by:Vincent Fortier (Bugzilla Bug 4768)
"At boot time the screen appears moved to the mid right portion of the actual
video pannel making the end of the line appears at the left edge... It simply
looks like moved half way to the right"
His particular hardware has a display with an unusual dimension (1920x1200) but
unfortunately has no EDID block. None of the entries in the global mode
database is correct for this particular display, and it particularly has
difficulty scaling up 640x480 (the default startup mode of nvidiafb) to
1920x1200 which causes the above described problem.
1, Add 1920x1200 to the global mode database.
2. Let nvidiafb base the startup mode from the flatpanel dimensions only if the
EDID block is absent, no boot mode parameter is specified by the user, and
a flatpanel/LCD display is attached.
Arnd Bergmann [Mon, 8 Aug 2005 04:12:42 +0000 (14:12 +1000)]
[PATCH] ppc64: add default config for BPA
This adds a bpa_defconfig file and make target. The config settings
are made for the current version of the Cell Processor Based Blade,
so there are not too many drivers enabled. A few more drivers might
get added in the future though.
James Bottomley [Mon, 8 Aug 2005 16:51:38 +0000 (11:51 -0500)]
[SCSI] Bug 4940 Repeatable Kernel Panic on Adaptec 2015S I20 device on bootup
From: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Prevent driver from loading if another driver (i2o) has already claimed
the resources associated with the card. Discussion associated with this
bug can be referenced at http://bugzilla.kernel.org/show_bug.cgi?id=4940
where it was agreed to use pci_request_regions in both the dpt_i2o and
the i2o driver to prevent both drivers loading on the same adapter(s).
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[PATCH] Move the fix to align node_end_pfns to a proper location
Move the fix to align node_end_pfns to a proper location. The earlier fix
made the node_remap_start_vaddr to get misaligned causing remap_numa_kva to
barf again :-/
Miklos Szeredi [Sun, 7 Aug 2005 16:42:25 +0000 (09:42 -0700)]
[PATCH] namespace.c: fix bind mount from foreign namespace
I'm resending this patch, because I still believe it's the correct fix.
Tested before/after applying the patch with a test application
available from:
http://www.inf.bme.hu/~mszeredi/nstest.c
Bind mount from a foreign namespace results in an un-removable mount.
The reason is that mnt->mnt_namespace is copied from the old mount in
clone_mnt(). Because of this check_mnt() in sys_umount() will fail.
The solution is to set mnt->mnt_namespace to current->namespace in
clone_mnt(). clone_mnt() is either called from do_loopback() or
copy_tree(). copy_tree() is called from do_loopback() or
copy_namespace().
When called (directly or indirectly) from do_loopback(), always
current->namspace is being modified: check_mnt(nd->mnt). So setting
mnt->mnt_namespace to current->namspace is the right thing to do.
When called from copy_namespace(), the setting of mnt_namespace is
irrelevant, since mnt_namespace is reset later in that function for
all copied mounts.
Jamie said:
This patch is correct. The old code was buggy for more fundamental and
serious reason: it broke the invariant that a tree of vfsmnts all have the
same value of mnt_namespace (and the same for the mnt_list list).
Olaf Hering [Sun, 7 Aug 2005 16:42:24 +0000 (09:42 -0700)]
[PATCH] remove linux/pagemap.h from linux/swap.h
sparc can not include linux/pagemap.h because of the following circular
dependency:
asm-sparc/pgtable include linux/swap.h
linux/swap.h include now linux/pagemap.h
linux/pagemap.h include linux/mm.h
linux/mm.h include asm/pgtable.h
It needs to have the swp_entry_t type fully visible in pgtable.h,
we can't work around this using macros.
Signed-off-by: Olaf Hering <olh@suse.de> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tom Duffy [Sun, 7 Aug 2005 16:42:16 +0000 (09:42 -0700)]
[PATCH] Make visws compile again
In file included from linux-2.6.13-rc5/arch/i386/kernel/timers/timer_pit.c:20:
linux-2.6.13-rc5/include/asm-i386/mach-visws/do_timer.h: In function `do_timer_overflow':
linux-2.6.13-rc5/include/asm-i386/mach-visws/do_timer.h:32: error: `i8259A_lock' undeclared (first use in this function)
linux-2.6.13-rc5/include/asm-i386/mach-visws/do_timer.h:32: error: (Each undeclared identifier is reported only once
linux-2.6.13-rc5/include/asm-i386/mach-visws/do_timer.h:32: error: for each function it appears in.)
make[3]: *** [arch/i386/kernel/timers/timer_pit.o] Error 1
make[2]: *** [arch/i386/kernel/timers] Error 2
make[1]: *** [arch/i386/kernel] Error 2
make: *** [_all] Error 2
Signed-off-by: Tom Duffy <thomas.duffy.99@alumni.brown.edu> Cc: Andrey Panin <pazke@orbita1.ru> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ivan Kokshaysky [Sun, 7 Aug 2005 09:49:59 +0000 (13:49 +0400)]
[PATCH] Fix restore of 64-bit PCI BAR's
For 64-bit BAR[i] only pci_dev->resource[i] is valid, ->resource[i+1]
slot is unused and contains zeroes in all fields.
So when we update a PCI BAR, all we need is just to check that we're
going to update a _valid_ resource.
Also make sure to write high bits - use "x >> 16 >> 16" (rather than the
simpler ">> 32") to avoid warnings on 32-bit architectures where we're
not going to have any high bits.
Russell King [Sun, 7 Aug 2005 13:20:26 +0000 (14:20 +0100)]
[PATCH] ARM: Make sa1100fb_display_dma_period() an inline function
This function produces a warning when CPU_FREQ=n. Since it's a very
simple calculation, make it inline instead of adding preprocessor
directives around it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When the sparse mem changes and the kexec changes
were merged into setup.c they came in, in the wrong order.
This patch changes the order so we don't run sparse_init
which uses the bootmem allocator until we all of the
reserve_bootmem calls has been made.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] i386 visws: Add machine_shutdown and emergency_restart
Another x86 subarchitecture bit I missed. This adds both
machine_emergency_restart missed in my reboot fixes and
machine_shutdown needed for kexec support.
projects / linux-beck.git / log