Ivan T. Ivanov [Tue, 7 Jul 2015 13:38:06 +0000 (16:38 +0300)]
arm64: dts: qcom: Enable USB manual pullup on msm8916
On msm8916 based chipset vbus is not routed to USB controller/phy
and controller driver therefore enables pull-up explicitly
before starting controller using usbcmd run/stop bit.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Ivan T. Ivanov [Thu, 21 May 2015 06:44:48 +0000 (09:44 +0300)]
arm64: dts: qcom: Fix apq8016-sbc board USB related pin definitions
USB2513B HUB reset line is connected to PMIC GPIO 3 not to GPIO 1.
TC7USB40MU Dual SPDT Switch select input line is connected to PMIC
GPIO 4 not to GPIO 2. Fix this. Remove unused LED nodes.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Andy Gross [Tue, 31 Mar 2015 19:26:15 +0000 (14:26 -0500)]
arm64: dts: qcom: Add APQ8016 SBC support
This patch set adds support for the APQ8016 SBC.
Signed-off-by: Andy Gross <agross@codeaurora.org>
[Srinivas Kandagatla]: rebased on top of kumars original patch Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Kumar Gala [Wed, 11 Mar 2015 20:51:19 +0000 (15:51 -0500)]
devicetree: bindings: Document qcom,msm-id and qcom,board-id
The top level qcom,msm-id and qcom,board-id are utilized by bootloaders
on Qualcomm MSM platforms to determine which device tree should be
utilized and passed to the kernel.
Cc: <devicetree@vger.kernel.org> Signed-off-by: Kumar Gala <galak@codeaurora.org>
Rob Herring [Thu, 10 Dec 2015 21:21:12 +0000 (15:21 -0600)]
arm64: dts: apq8016-sbc: add label properties for UART, I2C, and SPI
Add label properties to provide a way to identify UART, I2C and SPI
ports based on their connector names. This follows naming convention in
96boards CE spec. Ports without external connections are not labelled.
Signed-off-by: Rob Herring <robh@kernel.org> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Andy Gross <agross@codeaurora.org> Acked-by: Kevin Hilman <khilman@linaro.org> Tested-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
arm64: dts: set the default i2c pin drive strength to 16mA
2mA drive strength is not enough when we connect multiple i2c devices
on the bus with different pull up resistors.
This issue was detected when multiple i2c devices connected on the other side
of level shifters on Linaro sensor board. Maxing up to 16mA made i2c much stable.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
Currently the rates of the xo and sleep clocks are hard-coded in the
GCC driver, but this is a board layout description that actually should
be in the DT. Moving them into DT also allows us to insert the RPM
controlled clocks between the DT and GCC clocks.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org> Signed-off-by: Andy Gross <agross@codeaurora.org>
Stephen Boyd [Fri, 20 Nov 2015 23:31:19 +0000 (15:31 -0800)]
arm64: dts: qcom: Alias pm8916 on msm8916 devices
Add an alias for pm8916 on msm8916 based SoCs so that the newly
updated dtbTool can find the pmic compatible string and add the
pmic-id element to the QCDT header.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Andy Gross <agross@codeaurora.org>
Linus Torvalds [Sat, 9 Jan 2016 22:53:48 +0000 (14:53 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"A single fix for machines with pages > 4k (PPC mostly).
There's a bug in our optimal transfer size code where we don't account
for pages > 4k and can set the transfer size to be less than the page
size causing nasty failures"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
sd: Reject optimal transfer length smaller than page size
Linus Torvalds [Sat, 9 Jan 2016 22:44:44 +0000 (14:44 -0800)]
Merge tag 'pci-v4.4-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixlet from Bjorn Helgaas:
"This marks the TI DRA7xx host bridge driver as broken. Apparently it
has never worked without some additional out-of-tree code, so I'm
going to mark it broken now and remove it completely next cycle unless
it's fixed"
* tag 'pci-v4.4-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: dra7xx: Mark driver as broken
The reason is that start_shepherd_timer schedules the shepherd work item
which uses vmstat_wq (vmstat_shepherd) before setup_vmstat allocates
that workqueue so if the further initialization takes more than HZ we
might end up scheduling on a NULL vmstat_wq. This is really unlikely
but not impossible.
Fixes: 373ccbe59270 ("mm, vmstat: allow WQ concurrency to discover memory reclaim doesn't make any progress") Reported-by: kernel test robot <ying.huang@linux.intel.com> Signed-off-by: Michal Hocko <mhocko@suse.com> Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: stable@vger.kernel.org Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 9 Jan 2016 00:11:05 +0000 (16:11 -0800)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is the final small set of ARM SoC bug fixes for linux-4.4, almost
all regressions:
OMAP:
- data corruption on the Nokia N900 flash
Allwinner:
- Two defconfig change to get USB working again
ARM Versatile:
- Interrupt numbers gone bad after an older bug fix
Nomadik:
- Crashes from incorrect L2 cache settings
VIA vt8500:
- SD/MMC support on WM8650 never worked"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
dts: vt8500: Add SDHC node to DTS file for WM8650
ARM: Fix broken USB support in multi_v7_defconfig for sunxi devices
ARM: versatile: fix MMC/SD interrupt assignment
ARM: nomadik: set latencies to 8 cycles
ARM: OMAP2+: Fix onenand rate detection to avoid filesystem corruption
ARM: Fix broken USB support in sunxi_defconfig
Linus Torvalds [Fri, 8 Jan 2016 23:58:14 +0000 (15:58 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fix from Paolo Bonzini:
"A simple fix. I'm sending it before the merge window, because it
refines a patch found in your master branch but not yet in the
kvm/next branch that is destined for 4.5"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: x86: only channel 0 of the i8254 is linked to the HPET
Linus Torvalds [Fri, 8 Jan 2016 23:50:59 +0000 (15:50 -0800)]
Merge tag 'pm+acpi-4.4-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Just one obvious fix that adds a missing function argument in ACPI
code introduced recently (Kees Cook)"
* tag 'pm+acpi-4.4-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / property: avoid leaking format string into kobject name
Linus Torvalds [Fri, 8 Jan 2016 23:21:48 +0000 (15:21 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A handful of x86 fixes:
- a syscall ABI fix, fixing an Android breakage
- a Xen PV guest fix relating to the RTC device, causing a
non-working console
- a Xen guest syscall stack frame fix
- an MCE hotplug CPU crash fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/numachip: Fix NumaConnect2 MMCFG PCI access
x86/entry: Restore traditional SYSENTER calling convention
x86/entry: Fix some comments
x86/paravirt: Prevent rtc_cmos platform device init on PV guests
x86/xen: Avoid fast syscall path for Xen PV guests
x86/mce: Ensure offline CPUs don't participate in rendezvous process
Linus Torvalds [Fri, 8 Jan 2016 21:52:59 +0000 (13:52 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Two core subsystem fixes, plus a handful of tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix race in swevent hash
perf: Fix race in perf_event_exec()
perf list: Robustify event printing routine
perf list: Add support for PERF_COUNT_SW_BPF_OUT
perf hists browser: Fix segfault if use symbol filter in cmdline
perf hists browser: Reset selection when refresh
perf hists browser: Add NULL pointer check to prevent crash
perf buildid-list: Fix return value of perf buildid-list -k
perf buildid-list: Show running kernel build id fix
Linus Torvalds [Fri, 8 Jan 2016 20:23:00 +0000 (12:23 -0800)]
Merge tag 'dmaengine-fix-4.4' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Late fixes for 4.4 are three fixes for drivers which include a revert
of mic-x100 fix which is causing regression, xgene fix for double IRQ
and async_tx fix to use GFP_NOWAIT"
* tag 'dmaengine-fix-4.4' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: xgene-dma: Fix double IRQ issue by setting IRQ_DISABLE_UNLAZY flag
async_tx: use GFP_NOWAIT rather than GFP_IO
dmaengine: Revert "dmaengine: mic_x100: add missing spin_unlock"
Linus Torvalds [Fri, 8 Jan 2016 19:52:18 +0000 (11:52 -0800)]
Merge tag 'sound-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A slightly higher volume than a new year's wish, but not too
worrisome: a large LOC is only for HD-audio device-specific quirks, so
fairly safe to apply. The rest ASoC fixes are all trivial and small;
a simple replacement of mutex call with nested lock version, a few
Arizona and Realtek codec fixes, and a regression fix for Skylake
firmware handling"
* tag 'sound-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: Intel: Skylake: Fix the memory leak
ASoC: Intel: Skylake: Revert previous broken fix memory leak fix
ASoC: Use nested lock for snd_soc_dapm_mutex_lock
ASoC: rt5645: add sys clk detection
ALSA: hda - Add keycode map for alc input device
ALSA: hda - Add mic mute hotkey quirk for Lenovo ThinkCentre AIO
ASoC: arizona: Fix bclk for sample rates that are multiple of 4kHz
Arnd Bergmann [Fri, 8 Jan 2016 16:46:45 +0000 (17:46 +0100)]
Merge tag 'omap-for-v4.4/onenand-corruption' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Pull "urgent onenand file system corruption fix for n900" from Tony Lindgren:
Last minute urgent pull request to prevent file system corruption
on Nokia N900.
Looks like we have a GPMC bus timing bug that has gone unnoticed
because of bootloader configured registers until few days ago. We
are not detecting the onenand clock rate properly unless we have
CONFIG_OMAP_GPMC_DEBUG set and this causes onenand corruption
that can be easily be reproduced.
There seems to be also an additional bug still lurking around for
onenand corruption. But that is still being investigated and
it does not seem to be GPMC timings related.
Meanwhile, it would be good to get this fix into v4.4 to prevent
wrong timings from corrupting onenand.
* tag 'omap-for-v4.4/onenand-corruption' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix onenand rate detection to avoid filesystem corruption
If we end up splitting on the first segment, we don't adjust
the sector count. That results in hitting a BUG() with attempting
to split 0 sectors.
As this is just a performance issue and not a regression since
4.3 release, let's just rever this change. That gives us more
time to test a real fix for 4.5, which would be marked for
stable anyway.
Richard Cochran [Fri, 8 Jan 2016 15:58:31 +0000 (09:58 -0600)]
PCI: dra7xx: Mark driver as broken
Mark the dra7xx PCI host driver as broken. This driver was first merged in
v3.17 and has never worked. Although the driver compiles just fine, it is
missing an essential device reset. If the driver is included, the kernel
locks up hard shortly after booting, before any console output appears.
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
firmware: dmi_scan: Fix UUID endianness for SMBIOS >= 2.6
The dmi_ver wasn't updated correctly before the dmi_decode method run
to save the uuid.
That resulted in "dmidecode -s system-uuid" and
/sys/class/dmi/id/product_uuid disagreeing. The latter was buggy and
this fixes it.
Reported-by: Federico Simoncelli <fsimonce@redhat.com> Fixes: 9f9c9cbb6057 ("drivers/firmware/dmi_scan.c: fetch dmi version from SMBIOS if it exists") Fixes: 79bae42d51a5 ("dmi_scan: refactor dmi_scan_machine(), {smbios,dmi}_present()") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Jean Delvare <jdelvare@suse.de>
Linus Torvalds [Thu, 7 Jan 2016 20:56:23 +0000 (12:56 -0800)]
Merge tag 'iommu-fixes-v4.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- Two build issues, one in the ipmmu-vmsa driver and one for the new
generic dma-api implemention used on arm64
- A performance fix for said dma-api implemention
- An issue caused by a wrong offset in map_sg in the same code as above
* tag 'iommu-fixes-v4.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/dma: Use correct offset in map_sg
iommu/ipmmu-vmsa: Don't truncate ttbr if LPAE is not enabled
iommu/dma: Avoid unlikely high-order allocations
iommu/dma: Add some missing #includes
Linus Torvalds [Thu, 7 Jan 2016 20:42:22 +0000 (12:42 -0800)]
Merge tag 'trace-v4.4-rc4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace fix from Steven Rostedt:
"PeiyangX Qiu reported that if a module fails to load between calling
ftrace_module_init() and do_init_module() that the allocations made in
ftrace_module_init() will not be freed, resulting in a memory leak.
The solution is to call ftrace_release_mod() on the failing module in
the fail path befor do_init_module() is called. This will remove any
allocations made for that module, and nothing if ftrace_module_init()
wasn't called yet for that module.
Note, once do_init_module() is called, the MODULE_GOING notifiers are
called for the failed module, which calls into the ftrace code to do
the proper clean up (basically calling ftrace_release_mod())"
* tag 'trace-v4.4-rc4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace/module: Call clean up function when module init fails early
ftrace/module: Call clean up function when module init fails early
If the module init code fails after calling ftrace_module_init() and before
calling do_init_module(), we can suffer from a memory leak. This is because
ftrace_module_init() allocates pages to store the locations that ftrace
hooks are placed in the module text. If do_init_module() fails, it still
calls the MODULE_GOING notifiers which will tell ftrace to do a clean up of
the pages it allocated for the module. But if load_module() fails before
then, the pages allocated by ftrace_module_init() will never be freed.
Call ftrace_release_mod() on the module if load_module() fails before
getting to do_init_module().
Link: http://lkml.kernel.org/r/567CEA31.1070507@intel.com Reported-by: "Qiu, PeiyangX" <peiyangx.qiu@intel.com> Fixes: a949ae560a511 "ftrace/module: Hardcode ftrace_module_init() call into load_module()" Cc: stable@vger.kernel.org # v2.6.38+ Acked-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Roman Volkov [Fri, 1 Jan 2016 13:38:11 +0000 (16:38 +0300)]
dts: vt8500: Add SDHC node to DTS file for WM8650
Since WM8650 has the same 'WMT' SDHC controller as WM8505, and the driver
is already in the kernel, this node enables the controller support for
WM8650
Timo Sigurdsson [Fri, 1 Jan 2016 13:38:22 +0000 (14:38 +0100)]
ARM: Fix broken USB support in multi_v7_defconfig for sunxi devices
Commit 69fb4dcada77 ("power: Add an axp20x-usb-power driver") introduced a
new driver for the USB power supply used on various Allwinner based SBCs.
However, the driver was not added to multi_v7_defconfig which breaks USB
support for some boards (e.g. LeMaker BananaPi) as the kernel will now
turn off the USB power supply during boot by default if the driver isn't
present. (This was not the case in linux 4.3 or lower where the USB power
was always left on.)
Hence, add the driver to multi_v7_defconfig in order to keep USB support
working on those boards that require it.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de> Tested-by: Timo Sigurdsson <public_timo.s@silentcreek.de> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Paolo Bonzini [Thu, 7 Jan 2016 12:50:38 +0000 (13:50 +0100)]
kvm: x86: only channel 0 of the i8254 is linked to the HPET
While setting the KVM PIT counters in 'kvm_pit_load_count', if
'hpet_legacy_start' is set, the function disables the timer on
channel[0], instead of the respective index 'channel'. This is
because channels 1-3 are not linked to the HPET. Fix the caller
to only activate the special HPET processing for channel 0.
Reported-by: P J P <pjp@fedoraproject.org> Fixes: 0185604c2d82c560dab2f2933a18f797e74ab5a8 Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Robin Murphy [Mon, 4 Jan 2016 16:19:42 +0000 (16:19 +0000)]
iommu/dma: Use correct offset in map_sg
When mapping a non-page-aligned scatterlist entry, we copy the original
offset to the output DMA address before aligning it to hand off to
iommu_map_sg(), then later adding the IOVA page address portion to get
the final mapped address. However, when the IOVA page size is smaller
than the CPU page size, it is the offset within the IOVA page we want,
not that within the CPU page, which can easily be larger than an IOVA
page and thus result in an incorrect final address.
Fix the bug by taking only the IOVA-aligned part of the offset as the
basis of the DMA address, not the whole thing.
Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
dmaengine: xgene-dma: Fix double IRQ issue by setting IRQ_DISABLE_UNLAZY flag
For interrupt controller that doesn't support irq_disable and hardware
with level interrupt, an extra interrupt can be pending. This patch fixes
the issue by setting IRQ_DISABLE_UNLAZY flag for the interrupt line.
NeilBrown [Thu, 7 Jan 2016 00:02:34 +0000 (11:02 +1100)]
async_tx: use GFP_NOWAIT rather than GFP_IO
These async_XX functions are called from md/raid5 in an atomic
section, between get_cpu() and put_cpu(), so they must not sleep.
So use GFP_NOWAIT rather than GFP_IO.
Dan Williams writes: Longer term async_tx needs to be merged into md
directly as we can allocate this unmap data statically per-stripe
rather than per request.
Fixed: 7476bd79fc01 ("async_pq: convert to dmaengine_unmap_data") Cc: stable@vger.kernel.org (v3.13+) Reported-and-tested-by: Stanislav Samsonov <slava@annapurnalabs.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Linus Walleij [Tue, 5 Jan 2016 08:59:30 +0000 (09:59 +0100)]
ARM: versatile: fix MMC/SD interrupt assignment
Commit 0976c946a610d06e907335b7a3afa6db046f8e1b
"arm/versatile: Fix versatile irq specifications"
has an off-by-one error on the Versatile AB that has
been regressing the Versatile AB hardware for some time.
However it seems like the interrupt assignments have
never been correct and I have now adjusted them according
to the specification. The masks for the valid interrupts
made it impossible to assign the right SIC interrupt
for the MMCI, so I went in and fixed these to correspond
to the specifications, and added references if anyone
wants to double-check.
Due to the Versatile PB including the Versatile AB
as a base DTS file, we need to override and correct
some values to correspond to the actual changes in the
hardware.
For the Versatile PB I don't think the IRQ line
assignment for MMCI has ever been correct for either of
the two MMCI blocks. It would be nice if someone with the
physical PB board could test this.
Patch tested on the Versatile AB, QEMU for Versatile AB
and QEMU for Versatile PB.
Cc: Rob Herring <robh@kernel.org> Cc: Grant Likely <grant.likely@linaro.org> Cc: stable@vger.kernel.org Fixes: 0976c946a610 ("arm/versatile: Fix versatile irq specifications") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Walleij [Mon, 4 Jan 2016 01:18:28 +0000 (02:18 +0100)]
ARM: nomadik: set latencies to 8 cycles
The Nomadik has sporadic crashes because of these latencies, setting
them to max makes the platform work nicely, so use this values for
now.
These latencies were set to 2 since the Nomadik platform was merged,
but I suspect they never took effect until the right size and
associativity for the cache was specified in the device tree and
that is why the crash comes now.
Cc: stable@vger.kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Thu, 7 Jan 2016 04:32:08 +0000 (20:32 -0800)]
Merge tag 'for-linus-20160106' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Three last MTD fixes for v4.4. These are all fixes for regressions
and bugs reported mid cycle. Unfortunately, some of them took a bit
long to get proper testing and feedback.
- Assign the default MTD name earlier in the registration process, so
partition parsers (like cmdlinepart) see the right name. Without
this, some systems may come up with unpartitioned flash. This was
a v4.4-rc1 regression.
- Revert some new Winbond SPI NOR flash unlocking/locking support;
new code in v4.4 caused regressions on some Spansion flash.
- Fix mis-typed parameter ordering in SPI NOR unlock function; this
bug was introduced in v4.4-rc1"
* tag 'for-linus-20160106' of git://git.infradead.org/linux-mtd:
mtd: spi-nor: fix stm_is_locked_sr() parameters
mtd: spi-nor: fix Spansion regressions (aliased with Winbond)
mtd: fix cmdlinepart parser, early naming for auto-filled MTD
Pull networking fixes from David Miller:
"As usual, there are a couple straggler bug fixes:
1) qlcnic_alloc_mbx_args() error returns are not checked in qlcnic
driver. Fix from Insu Yun.
2) SKB refcounting bug in connector, from Florian Westphal.
3) vrf_get_saddr() has to propagate fib_lookup() errors to it's
callers, from David Ahern.
4) Fix AF_UNIX splice/bind deadlock, from Rainer Weikusat.
5) qdisc_rcu_free() fails to free the per-cpu qstats. Fix from John
Fastabend.
6) vmxnet3 driver passes wrong page to dma_map_page(), fix from
Shrikrishna Khare.
7) Don't allow zero cwnd in tcp_cwnd_reduction(), from Yuchung Cheng"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
tcp: fix zero cwnd in tcp_cwnd_reduction
Driver: Vmxnet3: Fix regression caused by 5738a09
net: qmi_wwan: Add WeTelecom-WPD600N
mkiss: fix scribble on freed memory
net: possible use after free in dst_release
net: sched: fix missing free per cpu on qstats
ARM: net: bpf: fix zero right shift
6pack: fix free memory scribbles
net: filter: make JITs zero A for SKF_AD_ALU_XOR_X
bridge: Only call /sbin/bridge-stp for the initial network namespace
af_unix: Fix splice-bind deadlock
net: Propagate lookup failure in l3mdev_get_saddr to caller
r8152: add reset_resume function
connector: bump skb->users before callback invocation
cxgb4: correctly handling failed allocation
qlcnic: correctly handle qlcnic_alloc_mbx_args
Yuchung Cheng [Wed, 6 Jan 2016 20:42:38 +0000 (12:42 -0800)]
tcp: fix zero cwnd in tcp_cwnd_reduction
Patch 3759824da87b ("tcp: PRR uses CRB mode by default and SS mode
conditionally") introduced a bug that cwnd may become 0 when both
inflight and sndcnt are 0 (cwnd = inflight + sndcnt). This may lead
to a div-by-zero if the connection starts another cwnd reduction
phase by setting tp->prior_cwnd to the current cwnd (0) in
tcp_init_cwnd_reduction().
To prevent this we skip PRR operation when nothing is acked or
sacked. Then cwnd must be positive in all cases as long as ssthresh
is positive:
1) The proportional reduction mode
inflight > ssthresh > 0
2) The reduction bound mode
a) inflight == ssthresh > 0
b) inflight < ssthresh
sndcnt > 0 since newly_acked_sacked > 0 and inflight < ssthresh
Therefore in all cases inflight and sndcnt can not both be 0.
We check invalid tp->prior_cwnd to avoid potential div0 bugs.
In reality this bug is triggered only with a sequence of less common
events. For example, the connection is terminating an ECN-triggered
cwnd reduction with an inflight 0, then it receives reordered/old
ACKs or DSACKs from prior transmission (which acks nothing). Or the
connection is in fast recovery stage that marks everything lost,
but fails to retransmit due to local issues, then receives data
packets from other end which acks nothing.
Fixes: 3759824da87b ("tcp: PRR uses CRB mode by default and SS mode conditionally") Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Bingkuo Liu <bingkuol@vmware.com> Signed-off-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The WeTelecom-WPD600N is an LTE module that, in addition to supporting most
"normal" bands, also supports LTE over 450MHz. Manual testing showed that
only interface number three replies to QMI messages.
Cc: Bjørn Mork <bjorn@mork.no> Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Alan [Wed, 6 Jan 2016 14:55:02 +0000 (14:55 +0000)]
mkiss: fix scribble on freed memory
commit d79f16c046086f4fe0d42184a458e187464eb83e fixed a user triggerable
scribble on free memory but added a new one which allows the user to
scribble even more and user controlled data into freed space.
As with 6pack we need to halt the queue before we free the buffers, because
the transmit logic is not protected by the semaphore.
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dst_release should not access dst->flags after decrementing
__refcnt to 0. The dst_entry may be in dst_busy_list and
dst_gc_task may dst_destroy it before dst_release gets a chance
to access dst->flags.
Fixes: d69bbf88c8d0 ("net: fix a race in dst_release()") Fixes: 27b75c95f10d ("net: avoid RCU for NOCACHE dst") Signed-off-by: Francesco Ruggeri <fruggeri@arista.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Takashi Iwai [Wed, 6 Jan 2016 19:53:28 +0000 (20:53 +0100)]
Merge tag 'asoc-fix-v4.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Last minute fixes for v4.4
A few final fixes for v4.4, the main one being the two patches to the
new Sky Lake drivers which fix a previous incorrect fix that went in
during an earlier -rc.
Tony Lindgren [Tue, 5 Jan 2016 20:04:20 +0000 (12:04 -0800)]
ARM: OMAP2+: Fix onenand rate detection to avoid filesystem corruption
Commit 63aa945b1013 ("memory: omap-gpmc: Add Kconfig option for debug")
unified the GPMC debug for the SoCs with GPMC. The commit also left out
the option for HWMOD_INIT_NO_RESET as we now require proper timings for
GPMC to be able to remap GPMC devices out of address 0.
Unfortunately on Nokia N900, onenand now only partially works with the
device tree provided timings. It works enough to get detected but the
clock rate supported by the onenand chip gets misdetected. This in turn
causes the GPMC timings to be miscalculated and this leads into file
system corruption on N900.
Looks like onenand needs CS_CONFIG1 bit 27 WRITETYPE set for for sync
write. This is needed also for async timings when we write to onenand
with omap2_onenand_set_async_mode(). Without sync write bit set, the
async read for the onenand ONENAND_REG_VERSION_ID will return 0xfff.
Let's exit with an error if onenand rate is not detected. And let's
remove the extra call to omap2_onenand_set_async_mode() as we only need
to do this once at the end of omap2_onenand_setup_async().
Fixes: 63aa945b1013 ("memory: omap-gpmc: Add Kconfig option for debug") Cc: stable@vger.kernel.org # v4.2+ Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Tony Lindgren <tony@atomide.com>
The -RT kernel managed to lockup itself with those. There could be multiple
attempts for task X to enqueue it for a wakeup _even_ if task X is already
running.
The reason is that task X could be runnable but not yet on CPU. The the
task performing the wakeup did not leave the CPU it could performe
multiple wakeups.
With the proper timming task X could be running and enqueued for a
wakeup. If this happens while X is performing a fork() then its its
child will have a !NULL `wake_q` member copied.
This is not a problem as long as the child task does not participate in
lockless wakeups :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Davidlohr Bueso <dbueso@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 7675104990ed ("sched: Implement lockless wake-queues") Link: http://lkml.kernel.org/r/20151221171710.GA5499@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
Our global init task can have sub-threads, so ->pid check is not reliable
enough for is_global_init(), we need to check tgid instead. This has been
spotted by Oleg and a fix was proposed by Richard a long time ago (see the
link below).
Oleg wrote:
: Because is_global_init() is only true for the main thread of /sbin/init.
:
: Just look at oom_unkillable_task(). It tries to not kill init. But, say,
: select_bad_process() can happily find a sub-thread of is_global_init()
: and still kill it.
I recently hit the problem in question; re-sending the patch (to the
best of my knowledge it has never been submitted) with updated function
comment. Credit goes to Oleg and Richard.
Suggested-by: Richard Guy Briggs <rgb@redhat.com> Reported-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Serge Hallyn <serge.hallyn@canonical.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Eric W . Biederman <ebiederm@xmission.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Serge E . Hallyn <serge.hallyn@ubuntu.com> Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://www.redhat.com/archives/linux-audit/2013-December/msg00086.html Signed-off-by: Ingo Molnar <mingo@kernel.org>
Andrey Ryabinin [Mon, 14 Dec 2015 12:47:23 +0000 (15:47 +0300)]
sched/fair: Fix multiplication overflow on 32-bit systems
Make 'r' 64-bit type to avoid overflow in 'r * LOAD_AVG_MAX'
on 32-bit systems:
UBSAN: Undefined behaviour in kernel/sched/fair.c:2785:18
signed integer overflow:
87950 * 47742 cannot be represented in type 'int'
The most likely effect of this bug are bad load average numbers
resulting in weird scheduling. It's also likely that this can
persist for a longer time - until the system goes idle for
a long time so that all load avg numbers get reset.
[ This is the CFS load average metric, not the procfs output, which
is separate. ]
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 9d89c257dfb9 ("sched/fair: Rewrite runnable load and utilization average tracking") Link: http://lkml.kernel.org/r/1450097243-30137-1-git-send-email-aryabinin@virtuozzo.com
[ Improved the changelog. ] Signed-off-by: Ingo Molnar <mingo@kernel.org>
Peter Zijlstra [Tue, 15 Dec 2015 12:49:05 +0000 (13:49 +0100)]
perf: Fix race in swevent hash
There's a race on CPU unplug where we free the swevent hash array
while it can still have events on. This will result in a
use-after-free which is BAD.
Simply do not free the hash array on unplug. This leaves the thing
around and no use-after-free takes place.
When the last swevent dies, we do a for_each_possible_cpu() iteration
anyway to clean these up, at which time we'll free it, so no leakage
will occur.
Which is a WARN_ON_ONCE() indicating that cpuctx->task_ctx is not
what we expected it to be.
This is because context switches can swap the task_struct::perf_event_ctxp[]
pointer around. Therefore you have to either disable preemption when looking
at current, or hold ctx->lock.
Fix perf_event_enable_on_exec(), it loads current->perf_event_ctxp[]
before disabling interrupts, therefore a preemption in the right place
can swap contexts around and we're using the wrong one.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Potapenko <glider@google.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kostya Serebryany <kcc@google.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: syzkaller <syzkaller@googlegroups.com> Link: http://lkml.kernel.org/r/20151210195740.GG6357@twins.programming.kicks-ass.net Signed-off-by: Ingo Molnar <mingo@kernel.org>
This reverts commit e958e079e254 ("dmaengine: mic_x100: add missing
spin_unlock").
The above patch is incorrect. There is nothing wrong with the original
code. The spin_lock is acquired in the "prep" functions and released
in "submit".
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
John Fastabend [Tue, 5 Jan 2016 17:11:36 +0000 (09:11 -0800)]
net: sched: fix missing free per cpu on qstats
When a qdisc is using per cpu stats (currently just the ingress
qdisc) only the bstats are being freed. This also free's the qstats.
Fixes: b0ab6f92752b9f9d8 ("net: sched: enable per cpu qstats") Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Rabin Vincent [Tue, 5 Jan 2016 17:34:04 +0000 (18:34 +0100)]
ARM: net: bpf: fix zero right shift
The LSR instruction cannot be used to perform a zero right shift since a
0 as the immediate value (imm5) in the LSR instruction encoding means
that a shift of 32 is perfomed. See DecodeIMMShift() in the ARM ARM.
Make the JIT skip generation of the LSR if a zero-shift is requested.
This was found using american fuzzy lop.
Signed-off-by: Rabin Vincent <rabin@rab.in> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
commit acf673a3187edf72068ee2f92f4dc47d66baed47 fixed a user triggerable free
memory scribble but in doing so replaced it with a different one that allows
the user to control the data and scribble even more.
sixpack_close is called by the tty layer in tty context. The tty context is
protected by sp_get() and sp_put(). However network layer activity via
sp_xmit() is not protected this way. We must therefore stop the queue
otherwise the user gets to dump a buffer mostly of their choice into freed
kernel pages.
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rabin Vincent [Tue, 5 Jan 2016 15:23:07 +0000 (16:23 +0100)]
net: filter: make JITs zero A for SKF_AD_ALU_XOR_X
The SKF_AD_ALU_XOR_X ancillary is not like the other ancillary data
instructions since it XORs A with X while all the others replace A with
some loaded value. All the BPF JITs fail to clear A if this is used as
the first instruction in a filter. This was found using american fuzzy
lop.
Add a helper to determine if A needs to be cleared given the first
instruction in a filter, and use this in the JITs. Except for ARM, the
rest have only been compile-tested.
Fixes: 3480593131e0 ("net: filter: get rid of BPF_S_* enum") Signed-off-by: Rabin Vincent <rabin@rab.in> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log