Helmut Schaa [Wed, 14 Dec 2011 15:28:41 +0000 (16:28 +0100)]
rt2x00: Make use of ieee80211_free_txskb in tx path
ieee80211_free_txskb should be used when dropping a frame in the device
rx path such that mac80211 knows about this frame being dropped.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Wed, 14 Dec 2011 04:43:17 +0000 (20:43 -0800)]
mwifiex: remove cfg_workqueue
cfg_workqueue was added to notify cfg80211 that scan, connect
or disconnect is done by calling respective completion handlers.
We can avoid use of this workqueue by calling those handlers
from other places.
1) Call connect, disconnect completion handlers in their callback
functions.
ex. Call cfg80211_connect_result() in mwifiex_cfg80211_connect()
2) Call scan completion handler after parsing response of last scan
command in a queue.
After removing the workqueue, variables (assoc_request etc.) and
checks used for mutual exclusion become redundant. Those are also
removed in this patch.
Johannes Berg [Tue, 13 Dec 2011 16:22:05 +0000 (17:22 +0100)]
nl80211: accept testmode dump with netdev
All nl80211 commands that need only the wiphy
still allow identifying it by giving an interface
index, except, as Kenny pointed out, the testmode
dump support.
Fix this by looking up the wiphy via the ifidx in
this case as well.
Tested-by: Kenny Hsu <kenny.hsu@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the case of HT40 after association on specified AP, but it break the
association for some APs and cause not able to establish connection.
We need to address HT40 before and after addociation.
CC: stable@vger.kernel.org #3.0+ Reported-by: Andrej Gelenberg <andrej.gelenberg@udo.edu> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Tested-by: Andrej Gelenberg <andrej.gelenberg@udo.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 14 Dec 2011 16:22:35 +0000 (08:22 -0800)]
iwlwifi: tx_sync only on PAN context
Ted reported that he couldn't connect to some APs
and bisected it to the tx_sync implementation.
Disable it for the BSS context to fix this issue.
Reported-by: Ted Ts'o <tytso@mit.edu> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex: avoid double list_del in command cancel path
Command cancel path cancels the current command and moves
it to free command queue. While doing that it deletes the
command entry from the pending list. This is not correct
as the entry has been already deleted from the pending
list at 'mwifiex_exec_next_cmd'. Fixing it.
Also making sure the stale command pointer is cleaned and
unaccessible for later use.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Tue, 13 Dec 2011 03:56:58 +0000 (19:56 -0800)]
mwifiex: do not advertise custom regulatory domain capability
mwifiex driver no longer supports it's own custom regulatory rules,
but custom regulatory domain capability is still advertised during
wiphy registration by the driver.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 12 Dec 2011 23:15:12 +0000 (15:15 -0800)]
brcm80211: smac: register with bcma for specific 802.11 core revisions
The brcmsmac driver has been verified on chipsets that were supported
when it was a pci device driver, ie. bcm4313, bcm43224, and bcm43225.
This patch restricts the driver to 802.11 core revisions that are found
in these chipsets.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 12 Dec 2011 23:15:09 +0000 (15:15 -0800)]
brcm80211: smac: remove mapped core related function from aiutils.c
In aiutils.c the selected core was maintained by its index number. This
is obsolete using BCMA functions so several functions using that index
have been removed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The macros were used to assure that the correct core was accessed in
the ISR, but register access is now done giving the explicit core so
no need to change interrupt state.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 12 Dec 2011 23:14:59 +0000 (15:14 -0800)]
brcm80211: smac: change ai_findcoreidx() to ai_findcore()
Instead of returning the core index the function now returns
the bcma device for the requested core id. This function is
now exposed in the header file.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Mon, 12 Dec 2011 13:30:04 +0000 (15:30 +0200)]
mac80211: don't check sdata_running in vif notifier
The ip address of the vif can be set even before the
vif is up. requiring the vif to be up in the vif
notifier makes the notifer ignore this event, which
causes wrong arp filter configuration later on.
Reported-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dmitry TARNYAGIN [Mon, 12 Dec 2011 11:58:43 +0000 (12:58 +0100)]
mac80211: Do not request FIF_BCN_PRBRESP_PROMISC for HW scan.
ieee80211_configure_filter code used local->scanning as a boolean
value when it was a bit mask. Bits SCAN_COMPLETED, SCAN_ABORTED
should not set FIF_BCN_PRBRESP_PROMISC filter.
SCAN_HW_SCANNING should not set FIF_BCN_PRBRESP_PROMISC either,
as there is no explicit filter configuration request from
scan code. If a driver requires FIF_BCN_PRBRESP_PROMISC mode
during HW scanning, it's up to the driver to temporary enable it.
Similar mistake was fixed also in ieee80211_hw_config (power
configuration code).
Verified-by: Vitaly Wool <vitaly.wool@sonyericsson.com> Signed-off-by: Dmitry Tarnyagin <dmitry.tarnyagin@stericsson.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
With previous patch "rtlwifi: use work for lps" we can now use mutex for
protecting ps mode changing critical sections. This fixes running system
with interrupts disabled for long time.
Merge ips_lock and lps_lock as they seems to protect the same data
structures (accessed in rtl_ps_set_rf_state() function).
Reported-by: Philipp Dreimann <philipp@dreimann.net> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Mike McCormack <mikem@ring3k.org> Cc: Chaoming Li <chaoming_li@realsil.com.cn> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Tested-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Leaving leisure power save mode can take some time, so it's better to
perform that action in process context with interrupts enabled. This
patch changes lps_leave tasklet to work.
Reported-by: Philipp Dreimann <philipp@dreimann.net> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Mike McCormack <mikem@ring3k.org> Cc: Chaoming Li <chaoming_li@realsil.com.cn> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Fri, 9 Dec 2011 04:41:04 +0000 (20:41 -0800)]
mwifiex: proper cleanup when RX multiport aggregation fails
Free SKBs allocated during multiport aggrgation setup when RX
multiport aggregation fails in the middle. With this handling
freeing SKB in mwifiex_process_int_status() for failure case
is removed.
Also handles single RX transaction failure.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Event buffers for PCIe interface are allocated during driver
initialisation, and respective physical addresses are sent to FW
in *_PCIE_DESC_DETAILS command so that FW can do DMA. These buffers
will be freed while unloading the driver. Therefore we should not
free them in event handling error path. Also we should skip next
pending events in failure case.
Also fixed 'returning -1 instead of -ENOMEM is sloppy' warnings.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcm80211: smac: replace ai_corereg() function with ai_cc_reg()
The ai_corereg() function is only used in the driver to safely
access the chipcommon core. The function has been renamed to
ai_cc_reg() removing the need to provide a core index parameter.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The use of SI_FAST() macro interferes with the BCMA integration as
it causes BCMA and aiutils.c to get out of sync on what the current
core is. When everything is using BCMA we will try to add SI_FAST
functionality to BCMA to avoid unnecessary core switching.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcm80211: smac: use DMA-API calls for descriptor allocations
Using BCMA hides the specifics about the host interface. The
driver is now using the DMA-API to do dma related calls. BCMA
provides the device object to use in the DMA-API calls.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcm80211: smac: use bcma core register access functions for 802.11 core
The driver now uses the bcma register access functions to read and
write the registers on the 802.11 core. The dma and phy code need
to be modified next and access to the other cores. That will be done
in coming patches.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcm80211: smac: remove enumeration rom parsing function
The core enumeration rom is already parsed by the bcma bus driver and
there is no need to repeat the exercise. The ai_scan() function still
exists but is targetted for removal as well.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcm80211: smac: rename struct si_info field pbus to pcibus
When moving to bcma usage there are two busses in play. The pci bus
connecting the device to the host and the bcma bus connecting the
cores in the device. To distinguish this the attribute pbus has been
renamed to a more explicit name, ie. pcibus.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcm80211: smac: change attach interfaces in main.c for bcma support
The driver is probed through bcma which provides a device representing
the core. This device is now passed in brcms_c_attach and brcms_b_attach
functions.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcm80211: smac: change from pci device driver to bcma device driver
A new bus driver called "bcma" has been introduced into the kernel tree
which considers the Broadcom AMBA chip interconnect as a bus. Each core in
the chip is a bcma device. This commit changes brcms_mac80211.c into
a bcma device driver.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcm80211: smac: use inline access functions for struct si_pub fields
Instead of directly accessing the fields in struct si_pub the driver
now uses inline access functions. This is in preparation of the bcma
integration as a lot of information will be provided by bcma module.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Reviewed-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma: add set/mask macros for 16-bit register access
The BCMA header only had definitions for 32-bit register access. Used
those as a template for the 16-bit flavour. Also changed them to inline
functions to be on the safe side. As offset parameter is used twice there
would be a problem when used like this: bcma_set32(core, offset++, val);
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Thu, 8 Dec 2011 23:06:40 +0000 (15:06 -0800)]
brcm80211: fmac: remove drive strength code for unsupported chips
bcm4325 and bcm4336 are not supported by brcmfmac. Remove the
drive strength setting code specific for these chips.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Thu, 8 Dec 2011 23:06:39 +0000 (15:06 -0800)]
brcm80211: fmac: add bcm4330 support
This patch adds support for bcm4330 chip which has a SDIO device
id 0x4330. All basic functionalities of bcm4330 are supported by
brcmfmac after this patch.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Thu, 8 Dec 2011 23:06:38 +0000 (15:06 -0800)]
brcm80211: fmac: fix firmware shared structures version
Some shared structures in fullmac have a wrong combination of
version number and declarations. This patch fixes it by upgrading
them to the latest version. This allows brcmfmac to support new
firmwares with new features.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Thu, 8 Dec 2011 23:06:37 +0000 (15:06 -0800)]
brcm80211: fmac: save bus interface structure in function 2 device
bus interface was stored in sdio card device. The device pointer
is used as parameter of interface functions between common layer
and bus layer to make the function declaration generic for different
bus type. But the card device is a parent device layer for SDIO
function devices. It doesn't contain all contexts needed by udev.
This patch moves the shared structure to private driver data pointer
of SDIO function 2 device which is more appopriate for net device
and cfg80211 registration.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211: notify core hints that helps to restore regd settings
Regulatory updates set by CORE are ignored for custom regulatory cards.
Let us notify the changes to the driver, as some drivers uses core hint
to restore its orig_* reg domain setting.
Cc: Paul Stewart <pstew@google.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the regulatory got updated by country IE for the world
roaming cards, need to reconfigure the tx power immediately to
increase the power level.
Reviewed-by: Sam Leffler <sleffler@google.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath: optimize processing of CTLs for country IEs for world roaming cards
When we receive a country IE hint and we have a world roaming card
we can optimize output power further by ensuring that we use the
calibrated data for the country by using that country's own CTL data.
That is -- when world roaming and when we process a country IE we
no longer need to use the lowest output power of all CTLs instead
we use an optimized CTL output power for that specific country.
We accomplish this by copying the regulatory data prior on init
and restoring it when cfg80211 tells us it gets a core hint. Core
hints are only sent on init and when it wants to restore reguulatory
settings. We take advantage of this fact and apply the cached
regulatory data when we get a core hint. When we get a country IE
hint though we process the regulatory data as if programmed for
a specific country.
Tested-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has no functional change. The helper can be used later
for other things like country IE changes and following the CTL
for different countries.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 8 Dec 2011 12:11:55 +0000 (13:11 +0100)]
mac80211: Make use of ieee80211_is_* functions in tx status path
Use ieee80211_is_data, ieee80211_is_mgmt and ieee80211_is_first_frag
in the tx status path. This makes the code easier to read and allows us
to remove two local variables: frag and type.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: Purge A-MPDU TX queues before station destructions
When a station leaves suddenly while ampdu traffic to that station is still
running, there is a possibility that the ampdu pending queues are not freed due
to a race condition leading to memory leaks. In '__sta_info_destroy' when we
attempt to destroy the ampdu sessions in 'ieee80211_sta_tear_down_BA_sessions',
the driver calls 'ieee80211_stop_tx_ba_cb_irqsafe' to delete the ampdu
structures (tid_tx) and splice the pending queues and this job gets queued in
sdata workqueue. However, the sta entry can get destroyed before the above work
gets scheduled and hence the race.
Purging the queues and freeing the tid_tx to avoid the leak. The better solution
would be to fix the race, but that can be taken up in a separate patch.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is quite possible to run into a race in bss timeout where
the drivers see the bss entry just before notifying cfg80211
of a roaming event but it got timed out by the time rdev->event_work
got scehduled from cfg80211_wq. This would result in the following
WARN-ON() along with the failure to notify the user space of
the roaming. The other situation which is happening with ath6kl
that runs into issue is when the driver reports roam to same AP
event where the AP bss entry already got expired. To fix this,
move cfg80211_get_bss() from __cfg80211_roamed() to cfg80211_roamed().
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
in my previous patches of handling MCI interrupt I overlooked
the case of interrupt status/mask variable being zeroed out in
the below code, so ath_isr does not cache the MCI interrupt
in the intrstatus. finally MCI interrupt handling won't be
handled in ath9k_tasklet for the scheduled interrupts.
Fix this by moving the MCI interrupt code in the appropriate
position in ar9003_hw_get_isr
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: check for asynchronous interrupts before bailing out
in ar9003_hw_get_isr we bail out if we don't have any primary
interrupts and synchronous interrupts, also make sure we don't
have any asynchronous interrupts
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The stations always chooses 1Mbps for all trasmitting frames,
whenever the AP is configured to lock the supported rates.
As the max phy rate is always set with the 4th from highest phy rate,
this assumption might be wrong if we have less than that. Fix that.
Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Reported-by: Ajay Gummalla <agummalla@google.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Fri, 9 Dec 2011 06:35:39 +0000 (09:35 +0300)]
nfc: signedness bug in __nci_request()
wait_for_completion_interruptible_timeout() returns -ERESTARTSYS if
interrupted so completion_rc needs to be signed. The current code
probably returns -ETIMEDOUT if we hit this situation, but after this
patch is applied it will return -ERESTARTSYS.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Thu, 8 Dec 2011 23:52:00 +0000 (15:52 -0800)]
iwlwifi: do not set the sequence control bit is not needed
Check the IEEE80211_TX_CTL_ASSIGN_SEQ flag from mac80211, then decide how to
set the TX_CMD_FLG_SEQ_CTL_MSK bit. Setting the wrong bit in BAR frame whill
make the firmware to increment the sequence number which is incorrect and
cause unknown behavior.
CC: stable@vger.kernel.org #3.0+ Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like the regression was introduced between 20111202 and 20111205 (linux-next tree). Symptoms: connection to AP seem to be
established, but no data goes though it in any way. Tested on intel
5300.
Peek at the changes have shown that it looks like at least part of
the code wasn't merged properly. It was originally committed into
iwl_agn.c but code in question was moved to iwl-mac80211.c.
This patch puts code in place and my card works again.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl12xx: silence tx_attr uninitialized warning in wl1271_tx_fill_hdr
CC [M] drivers/net/wireless/wl12xx/tx.o
drivers/net/wireless/wl12xx/tx.c: In function ‘wl1271_tx_fill_hdr’:
drivers/net/wireless/wl12xx/tx.c:288:6: warning: ‘tx_attr’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 2 Dec 2011 20:25:12 +0000 (12:25 -0800)]
iwlagn: use IWL_MAX_TID_COUNT instead of TID_MAX_LOAD_COUNT
We track the load only on 8 TIDs, previously this
was TID_MAX_LOAD_COUNT. Since IWL_MAX_TID_COUNT
is now 8 as well, use that to make the code more
easily understandable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 2 Dec 2011 20:22:54 +0000 (12:22 -0800)]
iwlagn: fix TID use bug
The driver everywhere uses max TID count as 9,
which is wrong, it should be 8.
I think the reason it uses 9 here is off-by-one
confusion by whoever wrote this. We do use the
value IWL_MAX_TID_COUNT for "not QoS/no TID"
but that is completely correct even if it is 8
and not 9 since 0-7 are only valid.
As a side effect, this fixes the following bug:
Open BA session requested for 00:23:cd:16:8a:7e tid 8
------------[ cut here ]------------
kernel BUG at drivers/net/wireless/iwlwifi/iwl-trans-pcie-int.h:350!
...
when you do
echo "tx start 8" > /sys/kernel/debug/ieee80211/*/*/*/*/agg_status
Cc: stable@vger.kernel.org Reported-by: Nikolay Martynov <mar.kolya@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
projects / linux-beck.git / log