SD8801 is Marvell's 1x1 802.11bgn offering.
This patch adds Device IDs for SD8801 and also defines card
structure which has definition for register offsets, buffer sizes etc.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Frank Huang <frankh@marvell.com> Reviewed-by: James Cameron <quozl@laptop.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hong Xu [Sat, 24 Jan 2015 11:34:03 +0000 (03:34 -0800)]
ath9k and ath9k_htc: rename variable "led_blink"
ath9k and ath9k_htc use the variable name "led_blink" to indicate
whether the module parameter "blink" is on. This name is easy to
conflict with other variables, and has caused a compiler error found
by kbuild test bot. The compiler error is as following:
drivers/net/wireless/ath/ath9k/ath9k_htc.o:(.data+0x47c): multiple definition of `led_blink'
drivers/net/wireless/ath/ath9k/ath9k.o:(.bss+0x20): first defined here
Fixes: 3a939a671225 ("ath9k_htc: Add a module parameter to disable blink") Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Hong Xu <hong@topbug.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Chun-Yeow Yeoh [Fri, 23 Jan 2015 08:59:24 +0000 (16:59 +0800)]
rtl8192cu: fix the mesh beaconing
Patch "rtlwifi: add support to send beacon frame" allows
the beaconing of rtl8192cu. But mesh beaconing is not
working. Fix this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Johannes Berg [Mon, 19 Jan 2015 10:24:36 +0000 (15:54 +0530)]
mwifiex: set netif carrier off in ndo_open
This patch adds fix to set carrier state off during ndo_open.
Carrier should be set to ON when device is ready to send data.
In case of station/adhoc interface device is able to transfer
data after successful association/join operation.
For AP this would be after bss_active event.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Mon, 19 Jan 2015 07:30:30 +0000 (08:30 +0100)]
bcma: use standard bus scanning during early register
Starting with kernel 3.19-rc1 early registration of bcma on MIPS is done
a bit later, with memory allocator available. This allows us to simplify
code by using standard bus scanning method.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rasmus Villemoes [Wed, 21 Jan 2015 11:52:07 +0000 (12:52 +0100)]
atmel: Remove open-coded and wrong strcasecmp
The kernel's string library does in fact have strcasecmp, at least
since ded220bd8f08 ("[STRING]: Move strcasecmp/strncasecmp to
lib/string.c"). Moreover, this open-coded version is in fact wrong: If
the strings only differ in their last character, a and b have already
been incremented to point to the terminating NUL bytes, so they would
wrongly be treated as equal.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
if(!wait_for_completion_interruptible_timeout(...))
only handles the timeout case - this patch adds handling the
signal case the same as timeout.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
if(!wait_for_completion_interruptible_timeout(...))
only handles the timeout case - this patch adds handling the
signal case the same as timeout.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
John Linville [Mon, 19 Jan 2015 19:09:15 +0000 (14:09 -0500)]
ath5k: document a fall-through case in ath5k_hw_set_opmode
Coverity: CID 114932
Signed-off-by: John W. Linville <linville@tuxdriver.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Fri, 16 Jan 2015 19:59:39 +0000 (20:59 +0100)]
bcma: clean bus initialization code
This moves main bus init code to the main.c and renames old function to
make its purpose clear.
Thanks to this change we'll also be able to separate scanning from
registration (and support PCIe Gen 2 devices) in the future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sabrina Dubroca [Mon, 19 Jan 2015 14:34:32 +0000 (15:34 +0100)]
b43: stop leds during suspend
Call b43_leds_stop during suspend to avoid this WARN:
WARNING: CPU: 1 PID: 0 at net/mac80211/util.c:755 ieee80211_can_queue_work.isra.11+0x35/0x50 [mac80211]()
queueing ieee80211 work while going to suspend
Dan Carpenter [Thu, 15 Jan 2015 11:43:40 +0000 (14:43 +0300)]
wlcore: unlock on error in wl1271_op_suspend()
We recently introduced a new error path which needs an unlock.
Fixes: 6d5a748d4836 ('wlcore: add ability to reduce FW interrupts during suspend') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hong Xu [Sun, 11 Jan 2015 19:45:53 +0000 (11:45 -0800)]
ath9k_htc: Add a module parameter to disable blink
Add an option "blink" to enable or disable the LED blink. The default
value is set to 1 so that existing users would not experience any
unexpected changes.
Signed-off-by: Hong Xu <hong@topbug.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bob Copeland [Fri, 9 Jan 2015 19:15:52 +0000 (14:15 -0500)]
wcn36xx: initiate TX BA sessions
Currently, wcn36xx only asks for a TX BA session if it has
already established one for RX. Thus, two wcn36xx devices cannot
do a-mpdu between themselves since they both wait for the other
to go first. Fix this by starting a BA session after a few QoS
data frames have been sent to a STA.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bob Copeland [Fri, 9 Jan 2015 19:15:51 +0000 (14:15 -0500)]
wcn36xx: move set_tx_pdu inside set_tx_data/mgmt
The pdu is part of the buffer descriptor, so it makes
sense that one function would fill both. Also, passing
the whole skb instead of just the header pointer to the
set_tx_data function paves the way for using its fields
for ampdu setup inside set_tx_data().
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bob Copeland [Fri, 9 Jan 2015 19:15:48 +0000 (14:15 -0500)]
wcn36xx: don't process 'valid' descriptors
The DMA engine will reset the valid bit after a descriptor is
complete; any with the valid bit still set may still be in
use by the hardware, so check that before freeing the descriptor.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bob Copeland [Fri, 9 Jan 2015 19:15:47 +0000 (14:15 -0500)]
wcn36xx: let device generate qos seq numbers
wcn36xx currently sends an incorrect sequence number into the BA session
setup firmware command: it should be saving or updating the ssn in the
TX_START ampdu_action callback instead of waiting until TX_OPERATIONAL.
However, we can sidestep the issue by letting the hardware generate the
sequence numbers for QoS frames, as is done in prima, so do that.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bob Copeland [Fri, 9 Jan 2015 19:15:46 +0000 (14:15 -0500)]
wcn36xx: use !! when assigning int as a boolean
bd->tx_comp is a single bit in a bitfield, so assigning
"info->flags & IEEE80211_TX_CTL_REQ_TX_STATUS" only happens
to work because TX_STATUS is defined to BIT(0); if it were
any other bit this assignment would fail.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex: check driver status in connect and scan handlers
Ignore scan and connection requests from cfg80211 when driver
unload is in process or previous command has timed out due to
a firmware bug. This patch fixes corner case system crash
issues.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sujith Manoharan [Fri, 19 Dec 2014 01:03:55 +0000 (06:33 +0530)]
ath9k: Fix no-ack frame status
Check if the frame has been completed without any
error and use IEEE80211_TX_STAT_NOACK_TRANSMITTED to
indicate successful transmission of no-ack frames.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Fri, 23 Jan 2015 15:51:54 +0000 (17:51 +0200)]
Merge tag 'iwlwifi-next-for-kalle-2015-01-22' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* more work for new devices (4165 / 8260)
* cleanups / improvemnts in rate control
* fixes for TDLS
* major statistics work from Johannes - more to come
* improvements for the fw error dump infrastructure
* usual amount of small fixes here and there (scan, D0i3 etc...)
Liad Kaufman [Thu, 22 Jan 2015 17:01:35 +0000 (19:01 +0200)]
iwlwifi: mvm: fix rx chains configuration in phy ctxt cmd
In the PHY_CTXT command sent to the FW the TX chains were
indeed configured by the values of both FW TLVs and of NVM,
but the RX chains were left out and configured only by FW
TLV.
This causes problems in 4165 HW, where there are 1x1
antennas, and the wrong configuration denies the driver
from connecting to the AP.
Eran Harary [Tue, 20 Jan 2015 13:37:34 +0000 (15:37 +0200)]
iwlwifi: pcie: support secured boot flow for family 8000 B step
The driver loads the 2 CPU sections, then it needs to let
the firmware know to start the authentication of the
sections. This is done by writing the relevants bits to
FH_UCODE_LOAD_STATUS.
For CPU1, the driver sets the lower 16 bits. For both CPUs,
the driver sets all the 32 bits.
Signed-off-by: Eran Harary <eran.harary@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Johannes Berg [Wed, 21 Jan 2015 17:05:04 +0000 (18:05 +0100)]
iwlwifi: mvm: rs: remove stats argument from functions
The stats argument is always only passed as &mvm->drv_rx_stats, so
there's no point in passing it when the mvm pointer is passed.
Remove the argument entirely.
Eyal Shapira [Thu, 15 Jan 2015 18:22:34 +0000 (20:22 +0200)]
iwlwifi: mvm: use a new API for enabling STBC
The new API tells the FW that it's allowed to use STBC
but the FW will decide on its own whether to use STBC
or SISO (and in the future Beamformer).
Keep support for the old API which sets STBC explicitly
in the rates in the LQ table while we still support old
FW revisions.
Eran Harary [Mon, 12 Jan 2015 08:43:58 +0000 (10:43 +0200)]
iwlwifi: mvm: support family 8000 C step
C step functionality in the driver is exactly the same as
B step besides the ucode name that present as iwlwifi-8000C-xx.ucode
instead of iwlwifi-8000B-xx.ucode
Signed-off-by: Eran Harary <eran.harary@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
John W. Linville [Mon, 12 Jan 2015 21:18:11 +0000 (16:18 -0500)]
iwlwifi: mvm: document switch case fall-through in iwl_mvm_send_sta_key
Add a comment indicating that the WLAN_CIPHER_SUITE_WEP104 case falls
through to the WLAN_CIPHER_SUITE_WEP40 case in iwl_mvm_send_sta_key.
This will document that the lack of a break is intentional.
Eyal Shapira [Mon, 12 Jan 2015 09:53:06 +0000 (11:53 +0200)]
iwlwifi: mvm: rs: use STBC regardless of power save mode
Tx STBC was used only when in CAM mode or if powersave is disabled.
Effectively this meant we never used STBC as these modes aren't
used on most platforms by default. Change that.
Revert "iwlwifi: mvm: drop non VO frames when flushing"
This is now implemented by mac80211 (commit below).
mac80211 will flush/drop the frames on the queues before
suspending / disconnecting.
It will then send the deauth and wait until the queues are
empty.
Merge tag 'tags/mac80211-next-for-davem-2015-01-19' into iwlwifi-next
Some further updates for net-next:
* fix network-manager which was broken by the previous changes
* fix delete-station events, which were broken by me making the
genlmsg_end() mistake
* fix a timer left running during suspend in some race conditions
that would cause an annoying (but harmless) warning
* (less important, but in the tree already) remove 80+80 MHz rate
reporting since the spec doesn't distinguish it from 160 MHz;
as the bitrate they're both 160 MHz bandwidth
Luciano Coelho [Wed, 14 Jan 2015 19:39:34 +0000 (21:39 +0200)]
iwlwifi: mvm: ignore temperature updates in the RX statistics notification
If the firmware sends spontaneous DTS notfications with the
temperature (indicated in a TLV), we can ignore the temperature we get
in the RX statistics notifications. This prevents potentially
handling the same temperature change twice. It also ignores
notifications with temperature equal to 0 that happens from time to
time.
Johannes Berg [Thu, 15 Jan 2015 11:59:26 +0000 (12:59 +0100)]
iwlwifi: mvm: generate statistics debugfs code
There's no need to duplicate the structure field name in the string,
just generate the string in the macro that's there anyway. To keep
the debugfs output the same, rename one (otherwise unused) field.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we want to trigger an NMI in the device, we need to set
bit 7 and not bit 0. However, older firmwares don't register
to the interrupt issued by bit 7. Use bit 7 first so that
the correct interrupt will be issued hoping that the firmware
will react. To be on the safe side, set bit 0 in case the
firmware didn't register to the proper interrupt.
Johannes Berg [Fri, 9 Jan 2015 13:15:32 +0000 (14:15 +0100)]
iwlwifi: mvm: add debugfs file for misbehaving U-APSD AP
As this functionality relies on getting a firmware notification
it is difficult to test. Allow accessing the data for it from
debugfs to be able to trigger all kinds of scenarios to test.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwlwifi: mvm: let the firmware configure the scheduler
A new host command can be used to configure the scheduler
instead of accessing the scheduler's registers from the
driver. This is easier and less error prone since accessing
the hardware at certain moments can lead to races with the
firmware.
Prefer to use the host command whenever it is available.
Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
David Spinadel [Mon, 29 Dec 2014 13:43:48 +0000 (15:43 +0200)]
iwlwifi: mvm: scan dwell time corrections
Use only basic dwell time (10 ms for active scan and 110 for passive),
regardless of the number of the probes and the band, if it is
supported by the FW. The FW will add 3 ms for each probe sent and 10
ms for low band channels.
Add a TLV flag to indicate such support in FW.
This fix is needed to fix few bugs regarding scans that take too much time.
Signed-off-by: David Spinadel <david.spinadel@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver doesn't support the firmwares that don't have
these capabilities. The code that actually used these
flags has been removed already, but the flags were left
for an unclear reason. Remove them.
Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Haim Dreyfuss [Thu, 18 Dec 2014 10:34:01 +0000 (12:34 +0200)]
iwlwifi: mvm: set max_out_time equal to frag_passive_dwell in fragmented scan
Fragmented scan should be applied for all channels, passive and active.
When scanning on passive channels the firmware uses frag_passive_dwell
to define the maximum continuous scan time before returning to the
operating channel. On active channels max_out_time is the parameter
used by the firmware to define the maximum time allowed out of the
operating channel. Since active channels' scan should also be fragmented
set max_out_time equal to frag_passive_dwell.
In addition:
- Set max_out_time and suspend_time if the firmware doesn't support
fragmented scan to avoid unexpected behavior.
- Adjust max_out_time for second level of scan precedence.
iwlwifi: mvm: allow to collect debug data from non-sleepable context
iwl_mvm_fw_dbg_collect allows to collect debug data from
the firmware. Most of the firmware interaction is done in
non-sleepable context. It makes little sense to force the
caller of iwl_mvm_fw_dbg_collect to sleep.
Defer the actual collection to a worker so that this
function will be able to be called from any context.
Reviewed-by: Eran Harary <eran.harary@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Liad Kaufman [Sun, 4 Jan 2015 09:03:13 +0000 (11:03 +0200)]
iwlwifi: mvm: make sure state isn't in d0i3 when stopping fw monitor
In case platform is in d0i3 - make sure it is awake when
writing the registers to stop the monitor when collecting FW
debug data. Plus, remove unneeded mutex locking currently
done.
iwlwifi: mvm: Add debugfs entry to enable scan offload notification
This option enables scan offload iteration complete notification from
firmware which includes the last iteration's status and the scanned
channels from the current iteration.
Eyal Shapira [Sun, 28 Dec 2014 20:12:38 +0000 (22:12 +0200)]
iwlwifi: mvm: rs: repeat initial legacy rates in LQ table
Repeating the legacy rates avoids degrading quickly to
lower rates due to collisions which is common when doing
TCP Tx traffic in legacy.
This slightly improves TCP Tx throughput while working
in legacy in different scenarios.
mac80211: delete the assoc/auth timer upon suspend
While suspending, we destroy the authentication /
association that might be taking place. While doing so, we
forgot to delete the timer which can be firing after
local->suspended is already set, producing the warning below.
Fix that by deleting the timer.
[66722.825487] WARNING: CPU: 2 PID: 5612 at net/mac80211/util.c:755 ieee80211_can_queue_work.isra.18+0x32/0x40 [mac80211]()
[66722.825487] queueing ieee80211 work while going to suspend
[66722.825529] CPU: 2 PID: 5612 Comm: kworker/u16:69 Tainted: G W O 3.16.1+ #24
[66722.825537] Workqueue: events_unbound async_run_entry_fn
[66722.825545] Call Trace:
[66722.825552] <IRQ> [<ffffffff817edbb2>] dump_stack+0x4d/0x66
[66722.825556] [<ffffffff81075cad>] warn_slowpath_common+0x7d/0xa0
[66722.825572] [<ffffffffa06b5b90>] ? ieee80211_sta_bcn_mon_timer+0x50/0x50 [mac80211]
[66722.825573] [<ffffffff81075d1c>] warn_slowpath_fmt+0x4c/0x50
[66722.825586] [<ffffffffa06977a2>] ieee80211_can_queue_work.isra.18+0x32/0x40 [mac80211]
[66722.825598] [<ffffffffa06977d5>] ieee80211_queue_work+0x25/0x50 [mac80211]
[66722.825611] [<ffffffffa06b5bac>] ieee80211_sta_timer+0x1c/0x20 [mac80211]
[66722.825614] [<ffffffff8108655a>] call_timer_fn+0x8a/0x300
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Oliver reported that it breaks network-manager, for some reason with
this patch NM decides that the device isn't wireless but "generic"
(ethernet), sees no carrier (as expected with wifi) and fails to do
anything else with it.
Revert this to unbreak userspace.
Reported-by: Oliver Hartkopp <socketcan@hartkopp.net> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we have an active scheduled scan, and the RFKILL
interrupt kicks in, the stack will cancel the scheduled
scan as part of the down flow. But cancelling scheduled
scan usually implies sending a command to the firwmare
which has been killed as part of the RFKILL interrupt
handling.
Because of that, we returned an error to mac80211 when
it asked to stop the scheduled scan and didn't notify the
end of the scheduled scan. Besides a fat warning, this led
to a situation in which cfg80211 would refuse any new scan
request.
To disentangle this, fake that the scheduled scan has been
stopped without sending the command to the firwmare, return
0 after having properly let cfg80211 know that the scan
has been cancelled.
This is basically the same as:
commit 9b520d84957d63348e87c0f2cbd21d86e1e8f2f2
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date: Tue Nov 4 15:54:11 2014 +0200
iwlwifi: mvm: abort scan upon RFKILL
This code existed but not for all the different FW APIs
we support.
Fix this.
Johannes Berg [Fri, 16 Jan 2015 20:05:02 +0000 (21:05 +0100)]
cfg80211: fix checking nl80211_send_station() return value
The return value from nl80211_send_station() is the length of the
skb, or a negative error, so abort sending the message only when
the return value was negative.
This fixes the ibss_rsn wpa_supplicant test case.
Reported-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 15 Jan 2015 15:14:02 +0000 (16:14 +0100)]
cfg80211: change bandwidth reporting to explicit field
For some reason, we made the bandwidth separate flags, which
is rather confusing - a single rate cannot have different
bandwidths at the same time.
Change this to no longer be flags but use a separate field
for the bandwidth ('bw') instead.
While at it, add support for 5 and 10 MHz rates - these are
reported as regular legacy rates with their real bitrate,
but tagged as 5/10 now to make it easier to distinguish them.
In the nl80211 API, the flags are preserved, but the code
now can also clearly only set a single one of the flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 15 Jan 2015 15:05:21 +0000 (16:05 +0100)]
cfg80211: remove 80+80 MHz rate reporting
These rates are treated the same as 160 MHz in the spec, so
it makes no sense to distinguish them. As no driver uses them
yet, this is also not a problem, just remove them.
In the userspace API the field remains reserved to preserve
API and ABI.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 15 Jan 2015 15:02:46 +0000 (16:02 +0100)]
mac80211: remove 80+80 MHz rate reporting
These rates are treated the same as 160 MHz in the spec,
so it makes no sense to distinguish them. As no driver
uses them yet, this is also not a problem, just remove
them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 6 Jan 2015 12:46:57 +0000 (13:46 +0100)]
orinoco/hermes: select CFG80211_WEXT
It makes no sense to require the user to find and enable
CFG80211_WEXT before the driver can be selected, make the
driver select the needed Kconfig symbol itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lorenzo Bianconi [Tue, 30 Dec 2014 22:10:19 +0000 (23:10 +0100)]
ath9k: add TPC to TX path for AR9002 based chips
Add TPC capability to TX descriptor path for AR9002 based chips. Scale
per-packet TX power according to eeprom power bias, power adjustments for
HT40 mode and open loop CCK rates. Cap per-packet TX power according to
TX power per-rate tables
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lorenzo Bianconi [Tue, 30 Dec 2014 22:10:18 +0000 (23:10 +0100)]
ath9k: add power per-rate tables for AR9002 chips
Add TX power per-rate tables for MIMO/legacy modes for AR9002 based chips
in order to cap the maximum TX power value per-rate in the TX descriptor path.
Add TX power adjustments for HT40 mode, open loop CCK rates and eeprom power
bias for AR9280 and later chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
bcma: fix three coding style issues, more than 80 characters per line
Three lines with more than 80 characters per line have been split in several lines.
Signed-off-by: Oscar Forner Martinez <oscar.forner.martinez@gmail.com> Acked-by: Rafa? Mi?ecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend van Spriel [Sat, 27 Dec 2014 13:13:00 +0000 (14:13 +0100)]
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
Use the helper to get rid of the file operations per debugfs file. The
device driver data contains struct ieee80211_hw pointer and the
struct ath9k_softc pointer is assigned to ieee80211_hw::priv so it can
be accessed in the seq_file read operation.
Cc: ath9k-devel@lists.ath9k.org Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the Rx reorder mechanism, nothing is done in the interrupt
context, so there is no need to use 'irq' flavors of spinlock.
Rx done in NAPI context (tasklet), other manipulations - in the
thread context.
Having interrupts enabled makes it better for the OS in general.
Besides, if enslaved under bonding, bridge or team driver, Rx
won't work with interrupts disabled.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the reordering block, Ethernet DA was checked for MCAST, this is wrong.
Check instead MCAST indication from 802.11 MAC header. Hardware saves
this into Rx descriptor.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wil6210: RX high threshold interrupt configuration
Rx high threshold interrupt is reported by the hardware in case
when number of not utilized by the HW descriptors in the Rx ring
becomes low.
Introduce module parameter for RX high threshold.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add advanced interrupt moderation support available since "Sparrow B0".
Legacy interrupt moderation used only one counter to moderate tx, rx,
and misc interrupts.
Advanced interrupt moderation bypasses misc, and handles separately tx
and rx interrupts. In addition it has two timers for each interrupt type.
Max burst duration timer which defines how long to postpone interrupt after
first event (receive event for rx and tx complete event for tx), and
interframe timeout which defines how to determine the end of the burst and
issue interrupt even if the first timer still pending.
Capabilities flags in wil_priv is set on initialization according to
HW. The rest of the code checks for advanced interrupt capability bit
in capabilities flags field.
Debugfs is split accordingly: "legacy" interrupt moderation remains
unchanged, new debugs files added for advanced interrupt moderation
support.
Module params are aligned to support advanced interrupt moderation
(tx & rx). When not available (for legacy interrupt moderation) will
use only rx configuration; Tx configuration will be ignored in this
case.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the proper reset follow based on HW capabilities
detection instead of chip ID.
Remove old hw ID mechanism which was used only for reset flow.
Remove support for Marlon A0.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable more flexible control over block ack:
- allow addba for any Tx vring
- allow to specify block ack timeout
- allow to delba for Tx or Rx side of any agreement; with reason
Renamed "addba" entry to "back"; it prints short help when read;
write:
- "add <ringid> <agg_size> <timeout>" to trigger ADDBA
If missing, <timeout> defaults to 0
- "del_tx <ringid> <reason>" to trigger DELBA for Tx side
- "del_rx <CID> <TID> <reason>" to trigger DELBA for Rx side
If missing, <reason> set to "STA_LEAVING" (36)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
projects / linux-beck.git / log