Alex Dubov [Wed, 14 Nov 2007 12:55:36 +0000 (23:55 +1100)]
tifm_sd: handle non-power-of-2 block sizes
It is possible to handle arbitrary block sizes with tifm card reader by
conditionally switching to PIO in case such block has to be delivered. At
the beginning of each request, DMA is either disabled (non-power-of-2 block
size) or set to load time user preference.
Signed-off-by: Alex Dubov <oakad@yahoo.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Mike Frysinger [Wed, 21 Nov 2007 08:12:12 +0000 (16:12 +0800)]
Blackfin arch: cplb and map header file cleanup
- remove duplicated defines for the BF561
- generalize L2 support (so that it works for BF54x) and mark it executable
- add support for reading/executing the Boot ROM sections
(since it has data/functions we may need at runtime)
- and fixup names for each map
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Wed, 21 Nov 2007 08:08:58 +0000 (16:08 +0800)]
Blackfin arch: add support for working around anomaly 05000312
Anomaly 05000312 - Errors When SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted:
DESCRIPTION:
When instruction cache is enabled, erroneous behavior may occur when any of the following instructions are interrupted:
. CSYNC
• SSYNC
• LCx =
• LTx = (only when LCx is non-zero)
• LBx = (only when LCx is non-zero)
When this problem occurs, a variety of incorrect things could happen, including an illegal instruction exception. Additional errors could
show up as an exception, a hardware error, or an instruction that is valid but different than the one that was expected.
WORKAROUND:
Place a cli before all SSYNC, CSYNC, "LCx =", "LTx =", and "LBx =" instructions to disable interrupts, and place an sti after each of these
instructions to re-enable interrupts. When these instructions are executed in code that is already non-interruptible, the problem will not
occur.
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Pavel Emelyanov [Wed, 21 Nov 2007 01:44:01 +0000 (17:44 -0800)]
[IPVS]: Fix compiler warning about unused register_ip_vs_protocol
This is silly, but I have turned the CONFIG_IP_VS to m,
to check the compilation of one (recently sent) fix
and set all the CONFIG_IP_VS_PROTO_XXX options to n to
speed up the compilation.
In this configuration the compiler warns me about
CC [M] net/ipv4/ipvs/ip_vs_proto.o
net/ipv4/ipvs/ip_vs_proto.c:49: warning: 'register_ip_vs_protocol' defined but not used
Indeed. With no protocols selected there are no
calls to this function - all are compiled out with
ifdefs.
Maybe the best fix would be to surround this call with
ifdef-s or tune the Kconfig dependences, but I think that
marking this register function as __used is enough. No?
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Acked-by: Simon Horman <horms@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Jonas Danielsson [Wed, 21 Nov 2007 01:38:16 +0000 (17:38 -0800)]
[ARP]: Fix arp reply when sender ip 0
Fix arp reply when received arp probe with sender ip 0.
Send arp reply with target ip address 0.0.0.0 and target hardware
address set to hardware address of requester. Previously sent reply
with target ip address and target hardware address set to same as
source fields.
Signed-off-by: Jonas Danielsson <the.sator@gmail.com> Acked-by: Alexey Kuznetov <kuznet@ms2.inr.ac.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the bug, refcnt for md5sig pool was leaked when
an user try to delete a key if we have more than one key.
In addition to the leakage, we returned incorrect return
result value for userspace.
This fix should close Bug #9418, reported by <ming-baini@163.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
ACPI: EC: Workaround for optimized controllers (version 3)
Some controllers fail to send confirmation GPE after address or data write.
Detect this and don't expect such confirmation in future.
This is a generalization of previous workaround
(66c5f4e7367b0085652931b2f3366de29e7ff5ec), which did only read address.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Tested-by: Romano Giannetti <romano.giannetti@gmail.com> Tested-by: Mats Johannesson Signed-off-by: Len Brown <len.brown@intel.com>
Márton Németh [Wed, 21 Nov 2007 00:23:26 +0000 (03:23 +0300)]
ACPI: EC: use printk_ratelimit(), add some DEBUG mode messages
Sometimes it is usefull to see raw protocol dump.
Uncomment '#define DEBUG' at the beginning of file to make EC
really verbose.
Signed-off-by: Márton Németh <nm127@freemail.hu> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Jeff Layton [Tue, 20 Nov 2007 23:19:03 +0000 (23:19 +0000)]
[CIFS] Fix potential data corruption when writing out cached dirty pages
Fix RedHat bug 329431
The idea here is separate "conscious" from "unconscious" flushes.
Conscious flushes are those due to a fsync() or close(). Unconscious
ones are flushes that occur as a side effect of some other operation or
due to memory pressure.
Currently, when an error occurs during an unconscious flush (ENOSPC or
EIO), we toss out the page and don't preserve that error to report to
the user when a conscious flush occurs. If after the unconscious flush,
there are no more dirty pages for the inode, the conscious flush will
simply return success even though there were previous errors when writing
out pages. This can lead to data corruption.
The easiest way to reproduce this is to mount up a CIFS share that's
very close to being full or where the user is very close to quota. mv
a file to the share that's slightly larger than the quota allows. The
writes will all succeed (since they go to pagecache). The mv will do a
setattr to set the new file's attributes. This calls
filemap_write_and_wait,
which will return an error since all of the pages can't be written out.
Then later, when the flush and release ops occur, there are no more
dirty pages in pagecache for the file and those operations return 0. mv
then assumes that the file was written out correctly and deletes the
original.
CIFS already has a write_behind_rc variable where it stores the results
from earlier flushes, but that value is only reported in cifs_close.
Since the VFS ignores the return value from the release operation, this
isn't helpful. We should be reporting this error during the flush
operation.
This patch does the following:
1) changes cifs_fsync to use filemap_write_and_wait and cifs_flush and also
sync to check its return code. If it returns successful, they then check
the value of write_behind_rc to see if an earlier flush had reported any
errors. If so, they return that error and clear write_behind_rc.
2) sets write_behind_rc in a few other places where pages are written
out as a side effect of other operations and the code waits on them.
3) changes cifs_setattr to only call filemap_write_and_wait for
ATTR_SIZE changes.
4) makes cifs_writepages accurately distinguish between EIO and ENOSPC
errors when writing out pages.
Some simple testing indicates that the patch works as expected and that
it fixes the reproduceable known problem.
Acked-by: Dave Kleikamp <shaggy@austin.rr.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
if debugging information is disabled. These messages are printed by
net_ratelimit(). Add a wrapper to net_ratelimit() that takes into account
the log level, so that net_ratelimit() is called only when we really want
to print something.
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Grant Likely [Wed, 17 Oct 2007 23:41:00 +0000 (17:41 -0600)]
[POWERPC] 83xx: Update mpc8349emitx(gp) defconfig for USB
USB support for the 8349itx got added a while back; but the defconfig
never got updated. This patch adds the appropriate USB config options
to the defconfigs
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> CC: Scott Wood <scottwood@freescale.com> CC: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kim Phillips [Thu, 8 Nov 2007 19:37:06 +0000 (13:37 -0600)]
[POWERPC] 8xxx: MDS board RTC fixes
Now the rtc class ds1374 driver has been added, remove the old rtc
driver hookup code, add rtc node to device trees, and turn on the
new driver in the defconfigs.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Johannes Berg [Fri, 16 Nov 2007 01:54:53 +0000 (02:54 +0100)]
mac80211: fix allmulti/promisc behaviour
When an interface with promisc/allmulti bit is taken down,
the mac80211 state can become confused. This fixes it by
making mac80211 keep track of all *active* interfaces that
have the promisc/allmulti bit set in the sdata, we sync
the interface bit into sdata at set_multicast_list() time
so this works.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 16 Nov 2007 00:49:11 +0000 (01:49 +0100)]
mac80211: fix ieee80211_set_multicast_list
I recently experienced unexplainable behaviour with the b43
driver when I had broken firmware uploaded. The cause may have
been that promisc mode was not correctly enabled or disabled
and this bug may have been the cause.
Note how the values are compared later in the function so
just doing the & will result in the wrong thing being
compared and the test being false almost always.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Takashi Iwai [Thu, 15 Nov 2007 12:16:02 +0000 (13:16 +0100)]
[ALSA] emu10k1 - Check value ranges in ctl callbacks
Check value ranges in ctl callbacks properly. This fixes the unexpected
crash due to wrong value assignment.
Also, remove invalid comments in the last patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Takashi Iwai [Mon, 29 Oct 2007 10:14:31 +0000 (11:14 +0100)]
[ALSA] portman2x4 - Fix probe error
Reported by Ingo Molnar,
when booting an allyesconfig bzImage kernel the bootup hangs in the
portman2x4 driver (on a box that does not have this hardware), at:
Pid: 1, comm: swapper
EIP: 0060:[<c02f763c>] CPU: 0
EIP is at parport_pc_read_status+0x4/0x8
EFLAGS: 00000202 Not tainted (2.6.23-rc9 #904)
EAX: f7e57a7f EBX: 00000010 ECX: c2b808c0 EDX: 00000379
ESI: f7cb8230 EDI: 00000010 EBP: f7cb8230 DS: 007b ES: 007b FS: 0000
CR0: 8005003b CR2: fff9c000 CR3: 007ec000 CR4: 00000690
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
[<c04613de>] portman_flush_input+0xde/0x12c
[<c0461a24>] snd_portman_probe+0x368/0x484
[<c02fbb8c>] __device_attach+0x0/0x8
[<c02fce68>] platform_drv_probe+0xc/0x10
[<c02fba6c>] driver_probe_device+0x74/0x194
[<c0587174>] klist_next+0x38/0x70
[<c02fbb8c>] __device_attach+0x0/0x8
[<c02faea1>] bus_for_each_drv+0x35/0x68
[<c02fbc22>] device_attach+0x72/0x78
the reason is due to an inconsistent error return code of 1 or 2, while
snd_portman_probe only realizes negative error codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Krzysztof Helt [Fri, 19 Oct 2007 06:23:00 +0000 (08:23 +0200)]
[ALSA] s3c2443-ac97: compilation fix
The Samsung S3C24xx uses new architecture file layout in the post 2.6.23
kernel. This patch fixes include path for the s3c2443-ac97.c.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Takashi Iwai [Mon, 19 Nov 2007 10:56:26 +0000 (11:56 +0100)]
[ALSA] hda-codec - Revert volume knob controls in STAC codecs
Volume knob controls with STAC codecs seem to cause problems with some
devices. Volumes change very slowly or silent suddenly. It's likely
due to conflict between the software and the hardware volume knob
setup.
Since we'll have a virtual master control in future, it's safer to
remove this control completely right now.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Evgeniy Polyakov [Tue, 20 Nov 2007 12:27:35 +0000 (04:27 -0800)]
[NETFILTER]: Fix kernel panic with REDIRECT target.
When connection tracking entry (nf_conn) is about to copy itself it can
have some of its extension users (like nat) as being already freed and
thus not required to be copied.
Actually looking at this function I suspect it was copied from
nf_nat_setup_info() and thus bug was introduced.
Report and testing from David <david@unsolicited.net>.
[ Patrick McHardy states:
I now understand whats happening:
- new connection is allocated without helper
- connection is REDIRECTed to localhost
- nf_nat_setup_info adds NAT extension, but doesn't initialize it yet
- nf_conntrack_alter_reply performs a helper lookup based on the
new tuple, finds the SIP helper and allocates a helper extension,
causing reallocation because of too little space
- nf_nat_move_storage is called with the uninitialized nat extension
So your fix is entirely correct, thanks a lot :) ]
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 20 Nov 2007 11:29:53 +0000 (03:29 -0800)]
[WIRELESS] WEXT: Fix userspace corruption on 64-bit.
On 64-bit systems sizeof(struct ifreq) is 8 bytes larger than
sizeof(struct iwreq).
For GET calls, the wireless extension code copies back into userspace
using sizeof(struct ifreq) but userspace and elsewhere only allocates
a "struct iwreq". Thus, this copy writes past the end of the iwreq
object and corrupts whatever sits after it in memory.
Fix the copy_to_user() length.
This particularly hurts the compat case because the wireless compat
code uses compat_alloc_userspace() and right after this allocated
buffer is the current bottom of the user stack, and that's what gets
overwritten by the copy_to_user() call.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cornelia Huck [Tue, 20 Nov 2007 10:13:41 +0000 (11:13 +0100)]
[S390] cio: Register/unregister subchannels only from kslowcrw.
Make sure all subchannel handling is done on the slow path workqueue
so that we don't have races between an old subchannel unregistering
and a new subchannel with the same name registering.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Tue, 20 Nov 2007 10:13:39 +0000 (11:13 +0100)]
[S390] Fix memory detection.
Before we're getting short on memory detection fixes here is the next
one: if neither sclp nor diag260 report the storage size the detection
loop will return immediately without detecting anything. Fix this by
breaking the detection loop only if the memory end is known.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The iucv is the only user of the various functions that are used to bring
parts of cpus up and down. Its the only allocpercpu user that will do
I/O on per cpu objects (which is difficult to do with virtually mapped memory).
And its the only use of allocpercpu where a GFP_DMA allocation is done.
Remove the allocpercpu calls from iucv and code the allocation and freeing
manually. After this patch it is possible to remove a large part of
the allocpercpu API.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Tue, 20 Nov 2007 10:13:37 +0000 (11:13 +0100)]
[S390] Dont overwrite lowcores on smp_send_stop().
Don't perform a sigp store-status-at-address on smp_send_stop().
It will overwrite the lowcores of other cpus and destroys valueable
debug informations.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[S390] Optimize storage key handling for anonymous pages
page_mkclean used to call page_clear_dirty for every given page. This
is different to all other architectures, where the dirty bit in the
PTEs is only resetted, if page_mapping() returns a non-NULL pointer.
We can move the page_test_dirty/page_clear_dirty sequence into the
2nd if to avoid unnecessary iske/sske sequences, which are expensive.
This change also helps kvm for s390 as the host must transfer the
dirty bit into the guest status bits. By moving the page_clear_dirty
operation into the 2nd if, the vm will only call page_clear_dirty
for pages where it walks the mapping anyway. There it calls
ptep_clear_flush for writable ptes, so we can transfer the dirty bit
to the guest.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Tue, 20 Nov 2007 10:13:35 +0000 (11:13 +0100)]
[S390] Fix kernel preemption.
When returning from IRQ handling and TIF_NEED_RESCHED is set we must
call preempt_schedule_irq() instead of schedule().
Otherwise the BKL might be unlocked in schedule() and therfore
everything that relies on the BKL is broken.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Tue, 20 Nov 2007 10:13:32 +0000 (11:13 +0100)]
[S390] Fix irq tracing and lockdep_sys_exit calls.
Current support for TRACE_IRQFLAGS and lockdep_sys_exit is broken.
IRQ flag tracing is broken for program checks. Even worse is that
the newly introduced calls to lockdep_sys_exit are in the critical
section code which is not supposed to call any C functions. In
addition the checks if locks are still held are also done when
returning to kernel code which is broken as well.
Fix all this by disabling interrupts and machine checks at the
exit paths and then do the appropriate checks and calls.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The only reason for doing a console_unblank on s390 is to flush the
log buffer. We have to check for in_atomic before doing a
console_unblank as the console is otherwise filled with an unrelated
bug message.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Sam Jansen [Tue, 20 Nov 2007 07:28:21 +0000 (23:28 -0800)]
[TCP]: Problem bug with sysctl_tcp_congestion_control function
From: "Sam Jansen" <sjansen@google.com>
sysctl_tcp_congestion_control seems to have a bug that prevents it
from actually calling the tcp_set_default_congestion_control
function. This is not so apparent because it does not return an error
and generally the /proc interface is used to configure the default TCP
congestion control algorithm. This is present in 2.6.18 onwards and
probably earlier, though I have not inspected 2.6.15--2.6.17.
sysctl_tcp_congestion_control calls sysctl_string and expects a successful
return code of 0. In such a case it actually sets the congestion control
algorithm with tcp_set_default_congestion_control. Otherwise, it returns the
value returned by sysctl_string. This was correct in 2.6.14, as sysctl_string
returned 0 on success. However, sysctl_string was updated to return 1 on
success around about 2.6.15 and sysctl_tcp_congestion_control was not updated.
Even though sysctl_tcp_congestion_control returns 1, do_sysctl_strategy
converts this return code to '0', so the caller never notices the error.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the abstraction functions got added, conversion here was
made incorrectly. As a result, the skb may end up pointing
to skb which got included to the probe skb and then was freed.
For it to trigger, however, skb_transmit must fail sending as
well.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Tue, 20 Nov 2007 06:51:24 +0000 (22:51 -0800)]
[PKTGEN]: Fix double unlock of xfrm_state->lock
The pktgen_output_ipsec() function can unlock this lock twice
due to merged error and plain paths. Remove one of the calls
to spin_unlock.
Other possible solution would be to place "return 0" right
after the first unlock, but at this place the err is known
to be 0, so these solutions are the same except for this one
makes the code shorter.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Shaohua Li [Sat, 17 Nov 2007 06:05:28 +0000 (01:05 -0500)]
ACPI: fix two IRQ8 issues in IOAPIC mode
Use mp_irqs[] to get PNP device's interrupt polarity and trigger.
There are two reasons to do this:
1. BIOS bug for PNP interrupt
2. BIOS explictly does override
mp_irqs[] should cover all the cases.
Simon Horman [Tue, 20 Nov 2007 05:51:13 +0000 (21:51 -0800)]
[IPVS]: Move remaining sysctl handlers over to CTL_UNNUMBERED
Switch the remaining IPVS sysctl entries over to to use CTL_UNNUMBERED,
I stronly doubt that anyone is using the sys_sysctl interface to
these variables.
Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Gala [Tue, 20 Nov 2007 05:36:23 +0000 (23:36 -0600)]
[POWERPC] Fix device tree interrupt map for Freescale ULI1575 boards
The interrupt map for the PCI PHB that had the ULI1575 was not correct
on the boards that have it.
* 8544 DS:
- Fix interrupt mask
- Be explicit about use of INTA for on chip peripherals
* 8572 DS/8641 HPCN:
- Fix interrupt mask
- Expand interrupt map for PCI slots to cover all functions
- Be explicit about use of INTA for on chip peripherals
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
[IPVS]: Fix sysctl warnings about missing strategy
Running the latest git code I get the following messages during boot:
sysctl table check failed: /net/ipv4/vs/drop_entry .3.5.21.4 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/drop_packet .3.5.21.5 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/secure_tcp .3.5.21.6 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/sync_threshold .3.5.21.24 Missing strategy
I removed the binary sysctl handler for those messages and also removed
the definitions in ip_vs.h. The alternative would be to implement a
proper strategy handler, but syscall sysctl is deprecated.
There are other sysctl definitions that are commented out or work with
the default sysctl_data strategy. I did not touch these.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Acked-by: Simon Horman <horms@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Neuling [Tue, 20 Nov 2007 04:18:40 +0000 (15:18 +1100)]
[POWERPC] Fix possible division by zero in scaled time accounting
If we get no user time and no system time allocated since the last
account_system_vtime, the system to user time ratio estimate can end
up dividing by zero.
This was causing a problem noticed by Balbir Singh.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Jeremy Kerr [Fri, 16 Nov 2007 02:32:23 +0000 (13:32 +1100)]
[POWERPC] spufs: Fix context destroy vs /spu readdir race
We can currently cause an oops by repeatedly creating and destroying
contexts, while doing getdents() calls on the "/spu" directory.
This is due to the context's top-level dentry remaining hashed while
the context is being destroyed.
Fix this by unhashing the context's dentry with the
dentry->d_inode->i_mutex held. This way, we'll hit the check for
d_unhashed in dentry_readdir, and won't be included in the
list of subdirs for /spu.
Linas Vepstas [Tue, 20 Nov 2007 01:28:15 +0000 (12:28 +1100)]
[POWERPC] Fix RTAS os-term usage on kernel panic
The rtas_os_term() routine was being called at the wrong time.
The actual rtas call "os-term" will not ever return, and so
calling it from the panic notifier is too early. Instead,
call it from the machine_reset() call.
This splits the rtas_os_term() routine into two: one part to capture
the kernel panic message, invoked during the panic notifier, and
another part that is invoked during machine_reset().
Prior to this patch, the os-term call was never being made,
because panic_timeout was always non-zero. Calling os-term
helps keep the hypervisor happy! We have to keep the hypervisor
happy to avoid service, dump and error reporting problems.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
currently the board-level PHY reset code for the mpc832x MDS messes with
reset configuration words source settings which is plain wrong (it
looks like this board code was cut-n-pasted from the mpc8360 mds code,
which has the PHY reset bits in a different BCSR); this patch points
the PHY reset code to the proper mpc832x mds PHY reset bits in the BCSR.
Signed-off-by: Peter Van Ackeren <peter.vanackeren@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>