Fix memory leak while receiving 8021q tagged packet which is not
registered by user.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In case debugfs does not init for some reason (or is disabled
on older kernels) driver does not allocate stats.fw_stats
structure, but tries to clear it later and trips on a NULL
pointer:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
PC is at __memzero+0x24/0x80
Backtrace:
[<bf0ddb88>] (wl1251_debugfs_reset+0x0/0x30 [wl1251])
[<bf0d6a2c>] (wl1251_op_stop+0x0/0x12c [wl1251])
[<bf0bc228>] (ieee80211_stop_device+0x0/0x74 [mac80211])
[<bf0b0d10>] (ieee80211_stop+0x0/0x4ac [mac80211])
[<c02deeac>] (dev_close+0x0/0xb4)
[<c02deac0>] (dev_change_flags+0x0/0x184)
[<c031f478>] (devinet_ioctl+0x0/0x704)
[<c0320720>] (inet_ioctl+0x0/0x100)
Add a NULL pointer check to fix this.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Acked-by: Kalle Valo <kalle.valo@iki.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a signal interrupts a Configure Endpoint command, the cmd_completion used
in xhci_configure_endpoint() is not re-initialized and the
wait_for_completion_interruptible_timeout() will return failure. Initialize
cmd_completion in xhci_configure_endpoint().
The EHCI driver stores in usb_host_endpoint.hcpriv a pointer to either
an ehci_qh or an ehci_iso_stream structure, and uses the contents of the
hw_info1 field to distinguish the two cases.
After ehci_qh was split into hw and sw parts, ehci_iso_stream must also
be adjusted so that it again looks like an ehci_qh structure.
This fixes a NULL pointer access in ehci_endpoint_disable() when it
tries to access qh->hw->hw_info1.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-by: Colin Fletcher <colin.m.fletcher@googlemail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When isochronous URBs are shorter than one frame and when more than one
ITD in a frame has been completed before the interrupt can be handled,
scan_periodic() completes the URBs in the order in which they are found
in the descriptor list. Therefore, the descriptor list must contain the
ITDs in the correct order, i.e., a new ITD must be linked in after any
previous ITDs of the same endpoint.
This should fix garbled capture data in the USB audio drivers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-by: Colin Fletcher <colin.m.fletcher@googlemail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1352) fixes a bug in the way isochronous input data is
returned to userspace for usbfs transfers. The entire buffer must be
copied, not just the first actual_length bytes, because the individual
packets will be discontiguous if any of them are short.
Reported-by: Markus Rechberger <mrechberger@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The TTY layer takes some care to ensure that only sub-page allocations
are made with interrupts disabled. It does this by setting a goal of
"TTY_BUFFER_PAGE" to allocate. Unfortunately, while TTY_BUFFER_PAGE takes the
size of tty_buffer into account, it fails to account that tty_buffer_find()
rounds the buffer size out to the next 256 byte boundary before adding on
the size of the tty_buffer.
This patch adjusts the TTY_BUFFER_PAGE calculation to take into account the
size of the tty_buffer and the padding. Once applied, tty_buffer_alloc()
should not require high-order allocations.
We allocate during interrupts so while our buffering is normally diced up
small anyway on some hardware at speed we can pressure the VM excessively
for page pairs. We don't really need big buffers to be linear so don't try
so hard.
In order to make this work well we will tidy up excess callers to request_room,
which cannot itself enforce this break up.
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is insufficient. The recvfrom methods must always call
svc_xprt_received on completion so that the socket gets re-queued if
there is any more work to do. This particular path did not make that
call because it actually destroyed the svsk, making requeue pointless.
When the svc_delete_socket was change to just set a bit, we should have
added a call to svc_xprt_received,
This is the problem that b0401d7253 attempted to fix, incorrectly.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit b0401d725334a94d57335790b8ac2404144748ee, which
moved svc_delete_xprt() outside of XPT_BUSY, and allowed it to be called
after svc_xpt_recived(), removing its last reference and destroying it
after it had already been queued for future processing.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can fix this by making the call to put_nfs_open_context() happen when we
actually remove the write request from the inode (which is done by the
nfsiod thread in this case).
If the NFS_INO_REVAL_FORCED flag is set, that means that we don't yet have
an up to date attribute cache. Even if we hold a delegation, we must
put a GETATTR on the wire.
The issue occur while deleting 60 virtual ports through the sys
interface /sys/class/fc_vports/vport-X/vport_delete. It happen while in
a mistake each request sent twice for the same vport. This interface is
asynchronous, entering the delete request into a work queue, allowing
more than one request to enter to the delete work queue. The result is a
NULL pointer. The first request already delete the vport, while the
second request got a pointer to the vport before the device destroyed.
Re-create vport later cause system freeze.
Solution: Check vport flags before entering the request to the work queue.
[jejb: fixed int<->long problem on spinlock flags variable] Signed-off-by: Gal Rosen <galr@storwize.com> Acked-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 71fe804b6d5 (mempolicy: use struct mempolicy pointer in
shmem_sb_info) added mpol=local mount option. but its feature is broken
since it was born. because such code always return 1 (i.e. mount
failure).
Fix an 'oops' when a tmpfs mount point is mounted with the mpol=default
mempolicy.
Upon remounting a tmpfs mount point with 'mpol=default' option, the mount
code crashed with a null pointer dereference. The initial problem report
was on 2.6.27, but the problem exists in mainline 2.6.34-rc as well. On
examining the code, we see that mpol_new returns NULL if default mempolicy
was requested. This 'NULL' mempolicy is accessed to store the node mask
resulting in oops.
Fix probe_point array-size overrun problem. In some cases (e.g.
inline function), one user-specified probe-point can be
translated to many probe address, and it overruns pre-defined
array-size. This also removes redundant MAX_PROBES macro
definition.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com> Cc: systemtap <systemtap@sources.redhat.com> Cc: DLE <dle-develop@lists.sourceforge.net>
LKML-Reference: <20100312232217.2017.45017.stgit@localhost6.localdomain6>
[ Note that only root can create new probes. Eventually we should remove
the MAX_PROBES limit, but that is a larger patch not eligible to
perf/urgent treatment. ] Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Anton Blanchard found that he could reliably make the kernel hit a
BUG_ON in the slab allocator by taking a cpu offline and then online
while a system-wide perf record session was running.
The reason is that when the cpu comes up, we completely reinitialize
the ctx field of the struct perf_cpu_context for the cpu. If there is
a system-wide perf record session running, then there will be a struct
perf_event that has a reference to the context, so its refcount will
be 2. (The perf_event has been removed from the context's group_entry
and event_entry lists by perf_event_exit_cpu(), but that doesn't
remove the perf_event's reference to the context and doesn't decrement
the context's refcount.)
When the cpu comes up, perf_event_init_cpu() gets called, and it calls
__perf_event_init_context() on the cpu's context. That resets the
refcount to 1. Then when the perf record session finishes and the
perf_event is closed, the refcount gets decremented to 0 and the
context gets kfreed after an RCU grace period. Since the context
wasn't kmalloced -- it's part of a per-cpu variable -- bad things
happen.
In fact we don't need to completely reinitialize the context when the
cpu comes up. It's sufficient to initialize the context once at boot,
but we need to do it for all possible cpus.
This moves the context initialization to happen at boot time. With
this, we don't trash the refcount and the context never gets kfreed,
and we don't hit the BUG_ON.
Reported-by: Anton Blanchard <anton@samba.org> Signed-off-by: Paul Mackerras <paulus@samba.org> Tested-by: Anton Blanchard <anton@samba.org> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Peter Zijlstra [Fri, 19 Mar 2010 01:00:19 +0000 (02:00 +0100)]
perf: Provide generic perf_sample_data initialization
This makes it easier to extend perf_sample_data and fixes a bug on arm
and sparc, which failed to set ->raw to NULL, which can cause crashes
when combined with PERF_SAMPLE_RAW.
It also optimizes PowerPC and tracepoint, because the struct
initialization is forced to zero out the whole structure.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Jean Pihet <jpihet@mvista.com> Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Cc: Jamie Iles <jamie.iles@picochip.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Stephane Eranian <eranian@google.com>
LKML-Reference: <20100304140100.315416040@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct a potential array overrun due to an off by one error in the
range check on the CAPI CONNECT_REQ CIPValue parameter.
Found and reported by Dan Carpenter using smatch.
Impact: bugfix Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the dummy LL interface to the LL interface change
introduced by commit daab433c03c15fd642c71c94eb51bdd3f32602c8.
This fixes the build failure occurring after that commit when
enabling ISDN_DRV_GIGASET but neither ISDN_I4L nor ISDN_CAPI.
Impact: bugfix Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Registering/unregistering the Gigaset CAPI driver when a device is
connected/disconnected causes an Oops when disconnecting two Gigaset
devices in a row, because the same capi_driver structure gets
unregistered twice. Fix by making driver registration/unregistration
a separate operation (empty in the ISDN4Linux case) called when the
main module is loaded/unloaded.
Impact: bugfix Signed-off-by: Tilman Schmidt <tilman@imap.cc> Acked-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Calling tty_buffer_request_room() before tty_insert_flip_string()
is unnecessary, costs CPU and for big buffers can mess up the
multi-page allocation avoidance.
Signed-off-by: Tilman Schmidt <tilman@imap.cc> Acked-by: Karsten Keil <keil@b1-systems.de> CC: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In RING handling, clear the table of received parameter strings in
a loop like everywhere else, instead of by enumeration which had
already gotten out of sync.
Impact: minor bugfix Signed-off-by: Tilman Schmidt <tilman@imap.cc> Acked-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the CMI8738 FRAME2 register is read, the chip sometimes (probably
when wrapping around) returns an invalid value that would be outside the
programmed DMA buffer. This leads to an inconsistent PCM pointer that is
likely to result in an underrun.
To work around this, read the register multiple times until we get a
valid value; the error state seems to be very short-lived.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-and-tested-by: Matija Nalis <mnalis-alsadev@voyager.hr> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/420578
The OR has verified that his hardware distorts because of the 0 dB
offset not corresponding to the highest PCM level. Fix this by capping
said PCM level to 0 dB similarly to what we do for CX20549 (Venice).
Reported-by: Mike Pontillo <pontillo@gmail.com> Tested-by: Mike Pontillo <pontillo@gmail.com> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Judging from the member of enable_msi white-list, Nvidia controller
seems to cause troubles with MSI enabled, e.g. boot hang up or other
serious issue may come up. It's safer to disable MSI as default for
Nvidia controllers again for now.
BugLink: https://bugs.launchpad.net/bugs/538895
The OR has verified that both position_fix=1 and model=6stack-dig are
necessary to have capture function properly. (The existing 3stack-6ch
model quirk seems to be incorrect.)
On platforms like dual socket quad-core platform, the scheduler load
balancer is not detecting the load imbalances in certain scenarios. This
is leading to scenarios like where one socket is completely busy (with
all the 4 cores running with 4 tasks) and leaving another socket
completely idle. This causes performance issues as those 4 tasks share
the memory controller, last-level cache bandwidth etc. Also we won't be
taking advantage of turbo-mode as much as we would like, etc.
Some of the comparisons in the scheduler load balancing code are
comparing the "weighted cpu load that is scaled wrt sched_group's
cpu_power" with the "weighted average load per task that is not scaled
wrt sched_group's cpu_power". While this has probably been broken for a
longer time (for multi socket numa nodes etc), the problem got aggrevated
via this recent change:
|
| commit f93e65c186ab3c05ce2068733ca10e34fd00125e
| Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
| Date: Tue Sep 1 10:34:32 2009 +0200
|
| sched: Restore __cpu_power to a straight sum of power
|
Also with this change, the sched group cpu power alone no longer reflects
the group capacity that is needed to implement MC, MT performance
(default) and power-savings (user-selectable) policies.
We need to use the computed group capacity (sgs.group_capacity, that is
computed using the SD_PREFER_SIBLING logic in update_sd_lb_stats()) to
find out if the group with the max load is above its capacity and how
much load to move etc.
Because symbol->end is not fixed up at symbol_filter time, only
after all symbols for a DSO are loaded, and that, for asm
symbols, may be bogus, causing segfaults when hits happen in
these symbols.
Looks like commit a6e4bc530403 didn't include updates to drivers so the
Blackfin CAN driver fails to build now.
Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bug is in virtio-pci: we use msix_vector as array index to get irq
entry, but some vqs do not have a dedicated vector so this causes an out
of bounds access. By chance, we seem to often get 0 value, which
results in this error.
Fix by verifying that vector is legal before using it as index.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Anthony Liguori <aliguori@us.ibm.com> Acked-by: Shirley Ma <xma@us.ibm.com> Acked-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some single chip family devices are sold in the market with
802.11n bonded out, these have no hardware capability for
02.11n but ath9k can still support them. These are called
AR2427.
Reported-by: Rolf Leggewie <bugzilla.kernel.org@rolf.leggewie.biz> Tested-by: Bernhard Reiter <ockham@raz.or.at> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the 82576NS Serdes adapter to the existing pci
quirk for 82576 parts.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch fixes a memory leak which occurs when an em28xx card with DVB
extension is unplugged or its DVB extension driver is unloaded. In
dvb_fini(), dev->dvb must be freed before being set to NULL, as is done
in dvb_init() in case of error.
Note that this bug is also present in the latest stable kernel release.
Modify uid check in do_coredump so as to not apply it in the case of
pipes.
This just got noticed in testing. The end of do_coredump validates the
uid of the inode for the created file against the uid of the crashing
process to ensure that no one can pre-create a core file with different
ownership and grab the information contained in the core when they
shouldn' tbe able to. This causes failures when using pipes for a core
dumps if the crashing process is not root, which is the uid of the pipe
when it is created.
The fix is simple. Since the check for matching uid's isn't relevant for
pipes (a process can't create a pipe that the uermodehelper code will open
anyway), we can just just skip it in the event ispipe is non-zero
Reverts a pipe-affecting change which was accidentally made in
A bug was found with Li Zefan's ftrace_stress_test that caused applications
to segfault during the test.
Placing a tracing_off() in the segfault code, and examining several
traces, I found that the following was always the case. The lock tracer
was enabled (lockdep being required) and userstack was enabled. Testing
this out, I just enabled the two, but that was not good enough. I needed
to run something else that could trigger it. Running a load like hackbench
did not work, but executing a new program would. The following would
trigger the segfault within seconds:
# echo 1 > /debug/tracing/options/userstacktrace
# echo 1 > /debug/tracing/events/lock/enable
# while :; do ls > /dev/null ; done
Enabling the function graph tracer and looking at what was happening
I finally noticed that all cashes happened just after an NMI.
1) | copy_user_handle_tail() {
1) | bad_area_nosemaphore() {
1) | __bad_area_nosemaphore() {
1) | no_context() {
1) | fixup_exception() {
1) 0.319 us | search_exception_tables();
1) 0.873 us | }
[...]
1) 0.314 us | __rcu_read_unlock();
1) 0.325 us | native_apic_mem_write();
1) 0.943 us | }
1) 0.304 us | rcu_nmi_exit();
[...]
1) 0.479 us | find_vma();
1) | bad_area() {
1) | __bad_area() {
After capturing several traces of failures, all of them happened
after an NMI. Curious about this, I added a trace_printk() to the NMI
handler to read the regs->ip to see where the NMI happened. In which I
found out it was here:
What was happening is that the NMI would happen at the place that a page
fault occurred. It would call rcu_read_lock() which was traced by
the lock events, and the user_stack_trace would run. This would trigger
a page fault inside the NMI. I do not see where the CR2 register is
saved or restored in NMI handling. This means that it would corrupt
the page fault handling that the NMI interrupted.
The reason the while loop of ls helped trigger the bug, was that
each execution of ls would cause lots of pages to be faulted in, and
increase the chances of the race happening.
The simple solution is to not allow user stack traces in NMI context.
After this patch, I ran the above "ls" test for a couple of hours
without any issues. Without this patch, the bug would trigger in less
than a minute.
Reported-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the trace iterator is read, tracing_start() and tracing_stop()
is called to stop tracing while the iterator is processing the trace
output.
These functions disable both the standard buffer and the max latency
buffer. But if the wakeup tracer is running, it can switch these
buffers between the two disables:
buffer = global_trace.buffer;
if (buffer)
ring_buffer_record_disable(buffer);
<<<--------- swap happens here
buffer = max_tr.buffer;
if (buffer)
ring_buffer_record_disable(buffer);
What happens is that we disabled the same buffer twice. On tracing_start()
we can enable the same buffer twice. All ring_buffer_record_disable()
must be matched with a ring_buffer_record_enable() or the buffer
can be disable permanently, or enable prematurely, and cause a bug
where a reset happens while a trace is commiting.
This patch protects these two by taking the ftrace_max_lock to prevent
a switch from occurring.
Found with Li Zefan's ftrace_stress_test.
Reported-by: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the ftrace code that resets the ring buffer it references the
buffer with a local variable, but then uses the tr->buffer as the
parameter to reset. If the wakeup tracer is running, which can
switch the tr->buffer with the max saved buffer, this can break
the requirement of disabling the buffer before the reset.
This warning in s_next() can be triggered by lseek():
[<c018b3f7>] ? s_next+0x77/0x80
[<c013e3c1>] warn_slowpath_common+0x81/0xa0
[<c018b3f7>] ? s_next+0x77/0x80
[<c013e3fa>] warn_slowpath_null+0x1a/0x20
[<c018b3f7>] s_next+0x77/0x80
[<c01efa77>] traverse+0x117/0x200
[<c01eff13>] seq_lseek+0xa3/0x120
[<c01efe70>] ? seq_lseek+0x0/0x120
[<c01d7081>] vfs_llseek+0x41/0x50
[<c01d8116>] sys_llseek+0x66/0xa0
[<c0102bd0>] sysenter_do_call+0x12/0x26
The iterator "leftover" variable is zeroed in the opening of the trace
file. But lseek can call s_start() which will call s_next() without
reseting the "leftover" variable back to zero, which might trigger
the WARN_ON_ONCE(iter->leftover) that is in s_next().
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
LKML-Reference: <4B8CE06A.9090207@cn.fujitsu.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the graph tracer is active, and a task is forked but the allocating of
the processes graph stack fails, it can cause crash later on.
This is due to the temporary stack being NULL, but the curr_ret_stack
variable is copied from the parent. If it is not -1, then in
ftrace_graph_probe_sched_switch() the following:
for (index = next->curr_ret_stack; index >= 0; index--)
next->ret_stack[index].calltime += timestamp;
Will cause a kernel OOPS.
Found with Li Zefan's ftrace_stress_test.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We support event unthrottling in breakpoint events. It means
that if we have more than sysctl_perf_event_sample_rate/HZ,
perf will throttle, ignoring subsequent events until the next
tick.
So if ptrace exceeds this max rate, it will omit events, which
breaks the ptrace determinism that is supposed to report every
triggered breakpoints. This is likely to happen if we set
sysctl_perf_event_sample_rate to 1.
This patch removes support for unthrottling in breakpoint
events to break throttling and restore ptrace determinism.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: K.Prasad <prasad@linux.vnet.ibm.com> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Callers of a stacktrace might pass bad frame pointers. Those
are usually checked for safety in stack walking helpers before
any dereferencing, but this is not the case when we need to go
through one more frame pointer that backlinks the irq stack to
the previous one, as we don't have any reliable address boudaries
to compare this frame pointer against.
This raises crashes when we record callchains for ftrace events
with perf because we don't use the right helpers to capture
registers there. We get wrong frame pointers as we call
task_pt_regs() even on kernel threads, which is a wrong thing
as it gives us the initial state of any kernel threads freshly
created. This is even not what we want for user tasks. What we want
is a hot snapshot of registers when the ftrace event triggers, not
the state before a task entered the kernel.
This requires more thoughts to do it correctly though.
So first put a guardian to ensure the given frame pointer
can be dereferenced to avoid crashes. We'll think about how to fix
the callers in a subsequent patch.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We currently enforce the !RW mapping for the kernel mapping that maps
holes between different text, rodata and data sections. However, kernel
identity mappings will have different RWX permissions to the pages mapping to
text and to the pages padding (which are freed) the text, rodata sections.
Hence kernel identity mappings will be broken to smaller pages. For 64-bit,
kernel text and kernel identity mappings are different, so we can enable
protection checks that come with CONFIG_DEBUG_RODATA, as well as retain 2MB
large page mappings for kernel text.
Konrad reported a boot failure with the Linux Xen paravirt guest because of
this. In this paravirt guest case, the kernel text mapping and the kernel
identity mapping share the same page-table pages. Thus forcing the !RW mapping
for some of the kernel mappings also cause the kernel identity mappings to be
read-only resulting in the boot failure. Linux Xen paravirt guest also
uses 4k mappings and don't use 2M mapping.
Fix this issue and retain large page performance advantage for native kernels
by not working hard and not enforcing !RW for the kernel text mapping,
if the current mapping is already using small page mapping.
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1266522700.2909.34.camel@sbs-t61.sc.intel.com> Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ring buffer resizing and resetting relies on a schedule RCU
action. The buffers are disabled, a synchronize_sched() is called
and then the resize or reset takes place.
But this only works if the disabling of the buffers are within the
preempt disabled section, otherwise a window exists that the buffers
can be written to while a reset or resize takes place.
Reported-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
LKML-Reference: <4B949E43.2010906@cn.fujitsu.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The beacon sent gating doesn't seem to work with any combination
of flags. Thus, buffered frames tend to stay buffered forever,
using up tx descriptors.
Instead, use the DBA gating and hold transmission of the buffered
frames until 80% of the beacon interval has elapsed using the ready
time. This fixes the following error in AP mode:
ath5k phy0: no further txbuf available, dropping packet
Add a comment to acknowledge that this isn't the best solution.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When using the external sleep clock in AP mode, the
TSF increments too quickly, causing beacon interval
to be much lower than it is supposed to be, resulting
in lots of beacon-not-ready interrupts.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=14802.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I/Q calibration was completely broken, resulting in a high number of CRC errors
on received packets. before i could see around 10% to 20% CRC errors, with this
patch they are between 0% and 3%.
1.) the removal of the mask in commit "ath5k: Fix I/Q calibration
(f1cf2dbd0f798b71b1590e7aca6647f2caef1649)" resulted in no mask beeing used
when writing the I/Q values into the register. additional errors in the
calculation of the values (see 2.) resulted too high numbers, exceeding the
masks, so wrong values like 0xfffffffe were written. to be safe we should
always use the bitmask when writing parts of a register.
2.) using a (s32) cast for q_coff is a wrong conversion to signed, since we
convert to a signed value later by substracting 128. this resulted in too low
numbers for Q many times, which were limited to -16 by the boundary check later
on.
3.) checked everything against the HAL sources and took over comments and minor
optimizations from there.
4.) we can't use ENABLE_BITS when we want to write a number (the number can
contain zeros). also always write the correction values first and set ENABLE
bit last, like the HAL does.
Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Experience has shown that the block buffer can only be used for SMBus
(not I2C) block transactions, even though the datasheet doesn't
mention this limitation.
Reported-by: Felix Rubinstein <felixru@gmail.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Oleg Ryjkov <oryjkov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Aaro Koskinen reported an issue in kernel.org bugzilla #15366, where
on non-GENERIC_TIME systems, accessing
/sys/devices/system/clocksource/clocksource0/current_clocksource
results in an oops.
It seems the timekeeper/clocksource rework missed initializing the
curr_clocksource value in the !GENERIC_TIME case.
Thanks to Aaro for reporting and diagnosing the issue as well as
testing the fix!
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: John Stultz <johnstul@us.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
LKML-Reference: <1267475683.4216.61.camel@localhost.localdomain> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since alc_auto_create_input_ctls() doesn't set the elements for the
secondary ADCs, "Input Source" elemtns for these also get empty, resulting
in buggy outputs of alsactl like:
control.14 {
comment.access 'read write'
comment.type ENUMERATED
comment.count 1
iface MIXER
name 'Input Source'
index 1
value 0
}
This patch fixes alc_mux_enum_*() (and others) to fall back to the
first entry if the secondary input mux is empty.
without the following patch audio ssttuutteerrs on
ASUS M2N32-SLI PREMIUM ACPI BIOS Revision 1304
the sound device is:
00:0e.1 Audio device: nVidia Corporation MCP55 High Definition Audio (rev a2)
worked with 2.6.32
forgot to update tg3_poll_controller(), leading to intermittent crashes with
netpoll.
Fix this.
Signed-off-by: Louis Rilling <louis.rilling@kerlabs.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Handling HT configuration changes involved setting the channel
with the new HT parameters and then issuing a rate_update()
notification to the driver.
This behavior changed after the off-channel changes. Now, the channel
is not updated with the new HT params in enable_ht() - instead, it
is now done when the scan work terminates. This results in the driver
depending on stale information, defaulting to non-HT mode always.
Fix this by passing the new channel type to the driver.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 2552fc2 changed the way the decompressor decides if it is safe
to decompress the kernel directly to its final location. Unfortunately,
it took the top of the compressed data as being the stack pointer,
which it is for ROM=n cases. However, for ROM=y, the stack pointer
is not relevant, and results in the wrong answer.
Fix this by explicitly storing the end of the biggybacked data in the
decompressor, and use that to calculate the compressed image size.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ARM kernel decompressor wants to be able to relocate r/w data
independently from the rest of the image, and we do this by ensuring that
r/w data has global visibility. Define STATIC_RW_DATA to be empty to
achieve this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Alain Knaff <alain@knaff.lu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The few lines below the kfree of hdr_buf may go to the label err_free
which will also free hdr_buf. The most straightforward solution seems to
be to just move the kfree of hdr_buf after these gotos.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
Distros generally (I looked at Debian, RHEL5 and SLES11) seem to
enable CONFIG_HIGHPTE for any x86 configuration which has highmem
enabled. This means that the overhead applies even to machines which
have a fairly modest amount of high memory and which therefore do not
really benefit from allocating PTEs in high memory but still pay the
price of the additional mapping operations.
Running kernbench on a 4G box I found that with CONFIG_HIGHPTE=y but
no actual highptes being allocated there was a reduction in system
time used from 59.737s to 55.9s.
With CONFIG_HIGHPTE=y and highmem PTEs being allocated:
Average Optimal load -j 4 Run (std deviation):
Elapsed Time 175.396 (0.238914)
User Time 515.983 (5.85019)
System Time 59.737 (1.26727)
Percent CPU 263.8 (71.6796)
Context Switches 39989.7 (4672.64)
Sleeps 42617.7 (246.307)
With CONFIG_HIGHPTE=y but with no highmem PTEs being allocated:
Average Optimal load -j 4 Run (std deviation):
Elapsed Time 174.278 (0.831968)
User Time 515.659 (6.07012)
System Time 55.9 (1.07799)
Percent CPU 263.8 (71.266)
Context Switches 39929.6 (4485.13)
Sleeps 42583.7 (373.039)
This patch allows the user to control the allocation of PTEs in
highmem from the command line ("userpte=nohigh") but retains the
status-quo as the default.
It is possible that some simple heuristic could be developed which
allows auto-tuning of this option however I don't have a sufficiently
large machine available to me to perform any particularly meaningful
experiments. We could probably handwave up an argument for a threshold
at 16G of total RAM.
Assuming 768M of lowmem we have 196608 potential lowmem PTE
pages. Each page can map 2M of RAM in a PAE-enabled configuration,
meaning a maximum of 384G of RAM could potentially be mapped using
lowmem PTEs.
Even allowing generous factor of 10 to account for other required
lowmem allocations, generous slop to account for page sharing (which
reduces the total amount of RAM mappable by a given number of PT
pages) and other innacuracies in the estimations it would seem that
even a 32G machine would not have a particularly pressing need for
highmem PTEs. I think 32G could be considered to be at the upper bound
of what might be sensible on a 32 bit machine (although I think in
practice 64G is still supported).
It's seems questionable if HIGHPTE is even a win for any amount of RAM
you would sensibly run a 32 bit kernel on rather than going 64 bit.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
LKML-Reference: <1266403090-20162-1-git-send-email-ian.campbell@citrix.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
setscheduler() saves task->sched_class outside of the rq->lock held
region for a check after the setscheduler changes have become
effective. That might result in checking a stale value.
rtmutex_setprio() has the same problem, though it is protected by
p->pi_lock against setscheduler(), but for correctness sake (and to
avoid bad examples) it needs to be fixed as well.
Retrieve task->sched_class inside of the rq->lock held region.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a SMT scheduler performance regression that is leading to a scenario
where SMT threads in one core are completely idle while both the SMT threads
in another core (on the same socket) are busy.
This is caused by this commit (with the problematic code highlighted)
On a SMT system, power of the HT logical cpu will be 589 and
the scheduler load imbalance (for scenarios like the one mentioned above)
can be approximately 1024 (SCHED_LOAD_SCALE). The above change of scaling
the weighted load with the power will result in "wl > imbalance" and
ultimately resulting in find_busiest_queue() return NULL, causing
load_balance() to think that the load is well balanced. But infact
one of the tasks can be moved to the idle core for optimal performance.
We don't need to use the weighted load (wl) scaled by the cpu power to
compare with imabalance. In that condition, we already know there is only a
single task "rq->nr_running == 1" and the comparison between imbalance,
wl is to make sure that we select the correct priority thread which matches
imbalance. So we really need to compare the imabalnce with the original
weighted load of the cpu and not the scaled load.
But in other conditions where we want the most hammered(busiest) cpu, we can
use scaled load to ensure that we consider the cpu power in addition to the
actual load on that cpu, so that we can move the load away from the
guy that is getting most hammered with respect to the actual capacity,
as compared with the rest of the cpu's in that busiest group.
Fix it.
Reported-by: Ma Ling <ling.ma@intel.com> Initial-Analysis-by: Zhang, Yanmin <yanmin_zhang@linux.intel.com> Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1266023662.2808.118.camel@sbs-t61.sc.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix for sched_mc_powersavigs for pre-Nehalem platforms.
Child sched domain should clear SD_PREFER_SIBLING if parent will have
SD_POWERSAVINGS_BALANCE because they are contradicting.
Sets the flags correctly based on sched_mc_power_savings.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20100208100555.GD2931@dirshya.in.ibm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't support these instructions, but guest can execute them even if the
feature('monitor') haven't been exposed in CPUID. So we would trap and inject
a #UD if guest try this way.
Signed-off-by: Sheng Yang <sheng@linux.intel.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Free the dm_io structure before calling bio_endio() instead of after it,
to ensure that the io_pool containing it is not referenced after it is
freed.
This partially fixes a problem described here
https://www.redhat.com/archives/dm-devel/2010-February/msg00109.html
thread 1:
bio_endio(bio, io_error);
/* scheduling happens */
thread 2:
close the device
remove the device
thread 1:
free_io(md, io);
Thread 2, when removing the device, sees non-empty md->io_pool (because the
io hasn't been freed by thread 1 yet) and may crash with BUG in mempool_free.
Thread 1 may also crash, when freeing into a nonexisting mempool.
To fix this we must make sure that bio_endio() is the last call and
the md structure is not accessed afterwards.
There is another bio_endio in process_barrier, but it is called from the thread
and the thread is destroyed prior to freeing the mempools, so this call is
not affected by the bug.
A similar bug exists with module unloads - the module may be unloaded
immediately after bio_endio - but that is more difficult to fix.
The else part of the if statement is indented but does not have braces
around it. It clearly should since it uses clk_enable and clk_disable
which are supposed to balance.
If no platform_data was givin to the device it's going to use it's default
platform data struct which has all fields initialized to zero. As a
result the driver is going to try to request gpio0 both as write protect
and card detect pin. Which of course will fail and makes the driver
unusable
Previously to the introduction of no_wprotect and no_detect the behavior
was to assume that if no platform data was given there is no write protect
or card detect pin. This patch restores that behavior.
The 'struct svc_deferred_req's on the xpt_deferred queue do not
own a reference to the owning xprt. This is seen in svc_revisit
which is where things are added to this queue. dr->xprt is set to
NULL and the reference to the xprt it put.
So when this list is cleaned up in svc_delete_xprt, we mustn't
put the reference.
Also, replace the 'for' with a 'while' which is arguably
simpler and more likely to compile efficiently.
Cc: Tom Tucker <tom@opengridcomputing.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This IBM system has a multi-function SDVO card that reports both VGA
and TV, but the system has no TV connector. The TV connector always
reported as connected, which would lead to poor modesetting choices.
projects / karo-tx-linux.git / log