Bhupesh Sharma [Fri, 23 Oct 2015 19:31:50 +0000 (01:01 +0530)]
arm64: Use generic Layerscape SoC family naming
Freescale will be a spinning-out a set of ARMv8 based SoCs which
will be based on a similar overall SoC architecture. So, this patch
converts the existing infrastructure in the arm64/dts, arm64/Kconfig
and arm64/configs to use the generic convention ARCH_LAYERSCAPE
in place of the more specific FSL_LS2085A, to save code duplication
later-on.
Arnd Bergmann [Fri, 23 Oct 2015 20:17:19 +0000 (22:17 +0200)]
Merge tag 'omap-for-v4.4/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap dts changes for v4.4 merge window, part 2" from Tony Lindgren:
Few more omap dts changes for v4.4 merge window, mostly to fix and clean
up some omap5 issues to allow adding other omap5 boards. Also some other
fixes and clean-up:
- Fix SDIO WLAN for omap5 that's been broken for a while. As further
patches are still needed for wl18xx, no need for stable on this one.
- Move most of omap5 support into omap5-board-common.dtsi as most omap5
boards seem to share the same basic set of devices.
- Add minimal IGEPv5 support using based on omap5-board-common.dtsi
- Remove now unneedes gpio hogging for dra72-evm
- Update Javier Martinez Canillas email address
- Change earlier IGEP boards to use IOPAD pinmux macros
* tag 'omap-for-v4.4/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-base0033: Use IOPAD pinmux macro
ARM: dts: am335x-igep0033: Use IOPAD pinmux macro
ARM: dts: omap3-igep0020: Use IOPAD pinmux macro
ARM: dts: am437x-gp-evm: Add wakeup interrupt source for pixcir_i2c_ts
ARM: dts: Update Javier Martinez Canillas's email
ARM: dts: dra72-evm: remove cpsw gpio hogging and add mode-gpios
ARM: dts: Add basic support for isee igepv5
ARM: dts: Move most of omap5-uevm.dts to omap5-board-common.dtsi
ARM: dts: Fix WLAN regression on omap5-uevm
Olof Johansson [Fri, 23 Oct 2015 17:51:21 +0000 (10:51 -0700)]
Merge tag 'imx-dt-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree changes for 4.4:
- Add IOMUXC LPSR (Low Power State Retention) device for i.MX7D.
- Add a few low power mode related devices and touch controller for
i.MX6UL.
- Add a number of devices for i.MX7D SDB board support, USB, Dual FEC,
and eMMC5.0.
- i.MX6 Boundary Devices updates: relicense under GPLv2/X11, add Okaya
LCD, touch and wifi support, add new boards Nitrogen6_Lite and
Nitrogen6_Max.
- Enable touch screen and NAND Flash controller for a few Vybrid
devices.
- Some random and small updates on LS1021A and MXS support.
* tag 'imx-dt-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (53 commits)
ARM: dts: ls1021a: Add quirk for Erratum A009116
ARM: imx6sx-sdb: Fix typo in regulator enable GPIO property
ARM: dts: imx6: phyFLEX: fix typo in "pinctrl-names"
ARM: dts: imx6: change the core clock of spdif
ARM: dts: vf-colibri: enable NAND flash controller
ARM: dts: vf610twr: add NAND flash controller peripherial
ARM: dts: imx: add Boundary Devices Nitrogen6_Lite board
ARM: dts: imx: add Boundary Devices Nitrogen6_Max board
ARM: dts: imx6dl-nitrogen6x: change manufacturer to Boundary Devices
ARM: dts: imx6q-nitrogen6x: change manufacturer to Boundary Devices
of: Add Boundary Devices Inc. vendor prefix
ARM: dts: imx6qdl-sabrelite: relicense under GPLv2/X11
ARM: dts: imx6qdl-nitrogen6x: relicense under GPLv2/X11
ARM: dts: imx6qdl-nitrogen6x: add wifi wl1271 support
ARM: dts: imx6dql-nitrogen6x: add touchscreen support
ARM: dts: imx6qdl-sabrelite: add Okaya LCD panel
ARM: dts: imx6qdl-nitrogen6x: add Okaya LCD panel
ARM: dts: vf500-colibri: Add device tree node for touchscreen support
ARM: dts: i.MX35: fix cpu compatible value
ARM: dts: i.MX31: fix cpu compatible value
...
Olof Johansson [Fri, 23 Oct 2015 17:19:04 +0000 (10:19 -0700)]
Merge tag 'v4.4-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
SPDIF device nodes for the newly added driver.
* tag 'v4.4-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add SPDIF optical out on Radxa Rock2 Square
ARM: dts: rockchip: Add SPDIF transceiver for RK3288
ARM: dts: rockchip: Add SPDIF optical out on Radxa Rock
ARM: dts: rockchip: Add SPDIF transceiver for RK3188
Olof Johansson [Fri, 23 Oct 2015 17:17:27 +0000 (10:17 -0700)]
Merge tag 'sunxi-dt-for-4.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Allwinner DT changes for 4.4, round 2
More DT patches for 4.4, mostly with new boards coming in (CHIP, BananaPi
M2, pcduino2), further consolidation for the q8-based designs and a bunch
of random patches enhancing support for existing boards
* tag 'sunxi-dt-for-4.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (27 commits)
ARM: dts: sun6i: Add a dts file for the Sinovoip BPI-M2 board
ARM: dts: sun6i: Add mmc2_pins_a pinmux setting to sun6i-a31.dtsi
ARM: dts: sunxi: Fix interrupt-cells for [r]pio on A23/A31/A33/A80
ARM: dts: sun8i: Add NMI interrupt controller node
ARM: dts: sun6i: hummingbird: Enable AXP221 DC5LDO regulator as "vdd-cpus"
ARM: dts: sun6i: hummingbird: Use axp22x.dtsi for AXP221 regulators
ARM: dts: sun6i: hummingbird: Fix VDD-CPU and VDD-GPU regulator names
ARM: dts: sun7i: Add regulator configuration for pcDuino v3 Nano
ARM: dts: sun6i: Turn on gmac on Colombus
ARM: dts: sun8i: Make et-q8-v1.6.dts a symlink to q8-tablet.dts
ARM: dts: sun8i: Make ippo-q8h-v*.dts a symlink to q8-tablet.dts
ARM: dts: sun8i: Add sun8i-a23-q8-tablet.dts file
ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi
ARM: dts: sunxi: Enable PWM controller on Q8 format tablets
ARM: dts: sun5i: Add PWM channel 0 pinmux setting for A13/A10s
ARM: dts: sun5i: Add PWM controller node for A13 / A10s
ARM: sun5i: Add C.H.I.P DTS
ARM: dts: sunxi: Add dtsi for AXP22x PMIC
ARM: dts: sun7i: Correct USB regulators on pcDuino v3 Nano
ARM: sun5i: dt: Add UART3 CTS and RTS pins
...
Olof Johansson [Thu, 22 Oct 2015 17:43:03 +0000 (10:43 -0700)]
Merge tag 'mvebu-dt-4.4-2' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.4 (part 2)
- Add support for severals Armada-370-based Seagate NAS
- Fix Ready NAS device tree
- Modify SDHCI binding for A388-GP allowing using it on old and new
version of the board
* tag 'mvebu-dt-4.4-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: set SW polling as SDHCI card detection on A388-GP
arm: mvebu: reorder nodes under internal-regs by address in RN2120 .dts file
arm: mvebu: disable unused Armada RTC on ReadyNAS 102, 104 and 2120
ARM: mvebu: add DT support for Seagate Personal Cloud
ARM: mvebu: add DT support for Seagate NAS 2 and 4-Bay
Use the AM33XX pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the AM33xx pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the OMAP3 pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Vignesh R [Wed, 14 Oct 2015 13:54:25 +0000 (19:24 +0530)]
ARM: dts: am437x-gp-evm: Add wakeup interrupt source for pixcir_i2c_ts
On am437x-gp-evm, pixcir_i2c_ts can wakeup the system from low power
state via pinctrl and IO daisy chain using generic wakeirq framework.
With commit 3fffd1283927 ("i2c: allow specifying separate wakeup
interrupt in device tree") i2c core allows optional wakeirq to be
specified via device tree. Add wakeup irq entry to enable pixcir_i2c_ts
to wake the system from low power state.
Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
I see that people are still sending emails to my old address (that no
longer exists) since is the one mentioned in the IGEP DTS. Replace it
with my current email address to avoid this.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mugunthan V N [Mon, 21 Sep 2015 14:53:51 +0000 (20:23 +0530)]
ARM: dts: dra72-evm: remove cpsw gpio hogging and add mode-gpios
With the current implementation of GPIO hogging and with
gpio-pcf857x is built as module, ethernet doesn't work on boot
and doesn't throw any error/warning to user. Ethernet becomes
operational when inserting gpio-pcf857x module, even this time
there is no error/warning logs to user that ethernet is
operational.
When using with NFS rootfs and gpio-pcf857x as module, board
doesn't boot as it doesn't get any ip address and doesn't throw
any error/warning. To over come this, now cpsw driver tries to
get mode-gpios. When gpio-pcf857x is built as module it will
throw error, so that user can decide either to built in
gpio-pcf857x to continue with nfs boot or choose alternate rootfs
filesystem like sd/ramdisk.
When using mmc/ramdisk as root fs, cpsw will probe defer and
re-probes again when gpio-pcf857x module is inserted and ethernet
becomes operational.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Big update of the sama5d2.dtsi file since many patches have reached te
mainline:
- add generated clocks
- enable crypto devices
- add flexcom devices
- add tdes device
- add sdmmc devices
MMC data lines may be left floating if nothing is currently driving the
data lines, which is the case when mmc is in idle state, thus consuming
a useless extra amount of power. Add pullup on mmc2 data signals in the
same way it was previously done for mmc0 and mmc1.
The PMC is not only used to drive the clocks but also has some registers
related to other functions. One of those is for example the USB gadget
bias.
Using a syscon allows to properly separate those functions.
Add "snps,quirk-frame-length-adjustment" property to
USB3 node for erratum A009116. This property provides
value of GFLADJ_30MHZ for post silicon frame length
adjustment.
Enable NAND access by adding pinmux and NAND flash controller node
to device tree. The NAND chips currently used on the Colibri VF61
requires 8-bit ECC per 512 byte page, hence specify 32-bit ECC
strength per 2k page size.
Reviewed-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the NAND flash controller (NFC) peripherial. The driver
supports the SLC NAND chips found on Freescale's Vybrid Tower System
Module. The Micron NAND chip on the module needs 4-bit ECC per 512
byte page. Use 24-bit ECC per 2k page, which is supported by the
driver.
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com> Reviewed-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gary Bisson [Wed, 30 Sep 2015 13:46:42 +0000 (15:46 +0200)]
of: Add Boundary Devices Inc. vendor prefix
This patch adds the vendor prefix for Boundary Devices Inc. which is a
supplier of ARM-based single board computers and System-on-Modules for
the general embedded market.
Website: http://boundarydevices.com/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gary Bisson [Wed, 30 Sep 2015 13:46:38 +0000 (15:46 +0200)]
ARM: dts: imx6dql-nitrogen6x: add touchscreen support
This patch adds the different touchscreens that can be connected using
the displays available for this board.
http://boundarydevices.com/product-category/displays/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ARM: dts: vf500-colibri: Add device tree node for touchscreen support
Add device tree node for touchscreen support on Colibri VF50. The
touchscreen functionality on VF50 uses the ADC channels of Vybrid
and some GPIOs. Also add pinctrl nodes for proper pinmux.
Adrian Alonso [Fri, 25 Sep 2015 21:05:57 +0000 (16:05 -0500)]
ARM: dts: imx: imx7d add iomuxc lpsr device node
Add device tree node to support iomuxc-lpsr controller, fsl,input-sel
phandle allows to get input select register base address which is
shared from main iomuxc controller.
Signed-off-by: Adrian Alonso <aalonso@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Haibo Chen [Fri, 28 Aug 2015 09:09:35 +0000 (17:09 +0800)]
ARM: dts: imx6ul.dtsi: add TSC support
Add imx6ul touchscreen controller support.
TSC module need ADC2 module to measure the touchscreen
coordinate value. This patch put TSC and ADC2 together,
make ADC2 module only be used for TSC, can't be used as
a normal ADC.
Starting with commit 8947e396a829 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Shawn Guo [Mon, 19 Oct 2015 14:45:01 +0000 (22:45 +0800)]
Merge tag 'imx-clk-4.4' into imx/dt
The i.MX clock updates for 4.4:
- A couple of fixes on i.MX31 and i.MX35 clock initialization functions
which makes mxc_timer_init() currently be called twice for DT boot.
- Increase i.MX6UL AXI bus clock rate to 264MHz which is the optimal
design target.
- Add a few missing clocks, ADC clock for i.MX7D, OCOTP clock for
Vybrid, and SPDIF_GCLK for i.MX6.
- A series from Lucas to fix early debug UART clock setup. This is
currently a one-off fix for i.MX platform, and can be extended to
become a generic solution later.
Hans de Goede [Thu, 15 Oct 2015 14:28:47 +0000 (16:28 +0200)]
ARM: dts: sun6i: Add a dts file for the Sinovoip BPI-M2 board
The Sinovoip BPI-M2 is a SBC board based on the A31s SoC it features
1G RAM, a microsd slot, Gbit ethernet, 4 usb-a USB-2 ports, ir receiver,
stereo headphone jack and hdmi video output.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Thu, 15 Oct 2015 14:28:45 +0000 (16:28 +0200)]
ARM: dts: sunxi: Fix interrupt-cells for [r]pio on A23/A31/A33/A80
When the gpio interrupt bindings where changed to add a bank to the
specifier list, the r_pio nodes of A23/A31/A33 where not updated to
match and neither was the pio node of the A80, this fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tony Lindgren [Fri, 16 Oct 2015 19:32:33 +0000 (12:32 -0700)]
ARM: dts: Add basic support for isee igepv5
With omap5-board-common.dtsi, we can now easily add support for various omap5
board variants. Let's add minimal support for isee igepv5.
So far I've tested that basic things work, such as serial, USB Ethernet, HDMI
and WLAN.
Note that like omap5-uevm, these boards seem to need to reserve 16MB for a
trap section as in commit 03178c66d289 ("ARM: dts: omap5-evm: Update
available memory to 2032 MB") and also noted in a u-boot commit at
http://marc.info/?l=u-boot&m=134376852603255 and also at
http://patchwork.ozlabs.org/patch/159881/.
Not sure why this is not needed for omap5-cm-t54.dts, maybe because of
different u-boot configuration.
Tony Lindgren [Fri, 16 Oct 2015 19:32:32 +0000 (12:32 -0700)]
ARM: dts: Move most of omap5-uevm.dts to omap5-board-common.dtsi
Looks like thevarious omap5-uevm models and igepv5 are very similar. So let's
create omap5-board-common.dtsi to allow fixing up things properly for mainline
kernel to support all these.
Even if we eventually end up having only PMIC + MMC + eMMC + SDIO WLAN + SATA +
USB + HDMI configuration in the omap5-board-common.dtsi, this is the easiest
way to add support for other boards rather than diffing various versions of
out of tree dts files.
My guess is that also omap5-sbc-t54.dts can use this, but I don't have that
board so that will need to be dealt with later on.
Tony Lindgren [Fri, 16 Oct 2015 19:32:32 +0000 (12:32 -0700)]
ARM: dts: Fix WLAN regression on omap5-uevm
Commit 99f84cae43df ("ARM: dts: add wl12xx/wl18xx bindings") added
device tree bindings for the TI WLAN SDIO on many omap variants.
I recall wondering how come omap5-uevm did not have the WLAN
added and this issue has been bugging me for a while now, and
I finally tracked it down to a bad pinmux regression, and a missing
deferred probe handling for the 32k clock from palmas that's
requested by twl6040.
Basically 392adaf796b9 ("ARM: dts: omap5-evm: Add mcspi data")
added pin muxing for mcspi4 that conflicts with the onboard
WLAN. While some omap5-uevm don't have WLAN populated, the
pins are not reused for other devices. And as the SDIO bus
should be probed, let's try to enable WLAN by default.
Let's fix the regression and add the WLAN configuration as
done for the other boards in 99f84cae43df ("ARM: dts: add
wl12xx/wl18xx bindings"). And let's use the new MMC pwrseq for
the 32k clock as suggested by Javier Martinez Canillas
<javier@dowhile0.org>.
Note that without a related deferred probe fix for twl6040,
the 32k clock is not initialized if palmas-clk is a module
and twl6040 is built-in.
Let's also use the generic "non-removable" instead of the
legacy "ti,non-removable" property while at it.
And finally, note that omap5 seems to require WAKEUP_EN for
the WLAN GPIO interrupt.
Marcin Wojtas [Thu, 15 Oct 2015 16:25:44 +0000 (18:25 +0200)]
ARM: mvebu: set SW polling as SDHCI card detection on A388-GP
The newest revisions of A388-GP (v1.5 and higher) support only
DAT3-based card detection. Revisions < v1.5 based on GPIO detection
via I2C expander, but this solution is supposed to be deprecated on
new boards. In order to satisfy all type of hardware this commit
changes card detection to use software polling mechanism. Also a
comment is added on possible card detection options in A388-GP
DT board file.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Arnd Bergmann [Thu, 15 Oct 2015 21:09:17 +0000 (23:09 +0200)]
Merge tag 'qcom-arm64-for-4.4' of git://codeaurora.org/quic/kernel/agross-msm into next/dt
Pull "Qualcomm ARM64 Updates for v4.4" from Andy Gross:
* Add RNG device tree node
* Add MSM8x16 serial UART1 node
* Enable eMMC on apq8016-sbc board
* Fix I2C pinconf sleep state function
* Add MSM8916 I2C nodes
* Enable I2C busses on LS and HS on APQ8016-sbc
* Enable SPI busses on LS and HS on APQ8016-sbc
* tag 'qcom-arm64-for-4.4' of git://codeaurora.org/quic/kernel/agross-msm:
arm64: dts: apq8016-sbc: enable spi buses on LS and HS
arm64: dts: apq8016-sbc: enable i2c buses on LS and HS
arm64: dts: qcom: Add msm8916 I2C nodes.
arm64: dts: fix i2c pinconf sleep state function
arm64: dts: qcom: Enable eMMC on apq8016-sbc board
arm64: dts: qcom: Add 8x16 Serial UART1 node
arm64: dts: qcom: Add RNG device tree node
Arnd Bergmann [Thu, 15 Oct 2015 20:38:10 +0000 (22:38 +0200)]
Merge tag 'juno-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt
Merge "SCPI support on ARM64 Juno Development Platform" from Sudeep Holla:
1. SRAM, MHU mailbox and SCPI support
2. CPU topology using cpu-map
3. Clock support for all the cpus
4. Support for SoC sensors
* tag 'juno-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: Add sensor node to Juno dt
arm64: dts: add clock support for all the cpus
arm64: dts: add CPU topology on Juno
arm64: dts: add SRAM, MHU mailbox and SCPI support on Juno
Arnd Bergmann [Thu, 15 Oct 2015 15:21:01 +0000 (17:21 +0200)]
Merge tag 'qcom-dt-for-4.4' of git://codeaurora.org/quic/kernel/agross-msm into next/dt
Pull "Qualcomm ARM Based Device Tree Updates for v4.4" from Andy Gross:
* Add DT binding document for SMEM
* Add SMD, RPM, and Regulator nodes on MSM8974
* Remove extra reg element from iadc device
* Remove redunandant i2c pinctrl properties on APQ8064
* Remove unnecessary eeprom label on IFC6410
* Remove unnecessary eeprom label from QS600
* Add PM8921 RTC support on APQ8064
* Add PM8921 pwrkey support on APQ8064
* Prefix GSBI6 uart pins on APQ8064 correctly
* Add missing GSBI7 uart pinctrl on APQ8064
* Add missing GSBI7 uart pinctrl on IFC6410
* Add missing GSBI7 pinctrl uart property on QS600
* Add pwrseq support for WLAN on IFC6410
* Add pwrseq support for WLAN on QS600
* Add notify led support on IFC6410
* Add SD card detect support onQS600
* Add #power-domain-cells property to documentation
* Add Qualcomm SMBB binding document
* Add PM8941 charge node
* Fix typo in disabled property on MSM8974
* tag 'qcom-dt-for-4.4' of git://codeaurora.org/quic/kernel/agross-msm:
ARM: dts: msm8974: fix typo in "disabled" property
ARM: dts: qcom-pm8941: Add charger node
dt-binding: power: Add Qualcomm SMBB binding
arm: dts: qcom: Add #power-domain-cells property
ARM: dts: qs600: Add SD card detect support.
ARM: dts: apq8064-ifc6410: add notify led support.
ARM: dts: qs600: add pwrseq support to WLAN
ARM: dts: ifc6410: Add pwrseq support for WLAN
ARM: dts: qs600: Add missing pinctrl property for gsbi7 uart
ARM: dts: ifc6410: Add missing pinctrl to gsbi7 uart
ARM: dts: apq8064: add missing gsbi7 uart pinctrl
ARM: dts: apq8064: Prefix the gsbi6 uart pins correctly
ARM: dts: apq8064: add pm8921 pwrkey support
ARM: dts: apq8064: add pm8921 rtc
ARM: dts: qs600: remove unnecessary eeprom label
ARM: dts: ifc6410: remove unnecessary eeprom label
ARM: dts: apq8064: remove redundant i2c pinctrl properties
ARM: dts: qcom: Remove extra reg element from iadc device
ARM: dts: msm8974: Add smd, rpm and regulator nodes
soc: qcom: Add device tree binding for SMEM
Linus Walleij [Thu, 15 Oct 2015 10:20:15 +0000 (12:20 +0200)]
ARM64: juno: add NOR flash to device tree
The Juno motherboard has a NOR flash on the motherboard, enable
this to be accessed with the CFI flash driver. Results after
enabling MTD, MTD_CFI, MTD_PHYSMAP, MTD_PHYSMAP_OF,
MTD_CFI_INTELEXT:
8000000.flash: Found 2 x16 devices at 0x0 in 32-bit bank.
Manufacturer ID 0x000089 Chip ID 0x008919
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Using buffer write method
Using auto-unlock on power-up/resume
cfi_cmdset_0001: Erase suspend on write enabled
erase region 0: offset=0x0,size=0x40000,blocks=255
erase region 1: offset=0x3fc0000,size=0x10000,blocks=4
Masahiro Yamada [Thu, 15 Oct 2015 09:05:32 +0000 (18:05 +0900)]
ARM: dts: uniphier: change the external bus address mapping
In UniPhier SoCs before ProXstream2 and PH1-LD6b, two address spaces
0x00000000 - 0x0fffffff
0x40000000 - 0x4fffffff
are both mapped to the external bus (also called system bus),
so either was OK.
In the newest two SoCs, the former (0x00000000 - 0x0fffffff) is
assigned for the serial NOR interface.
For the consistency, use the latter for all the SoCs.
Also, fix the range properties to reflect the real address mapping,
where the support card is located at the offset address 0x01f00000
of CS1 of the external bus.
Maxime Coquelin [Thu, 1 Oct 2015 15:48:19 +0000 (17:48 +0200)]
ARM: dts: Enable Ethernet on STi's B2199 board
The B2199 board is mounted with Realtek RTL8367 switch.
We consider the bootloader will have intiliazed the switch before jumping into
the kernel, so we declare it as a fixed link.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Maxime Coquelin [Thu, 1 Oct 2015 15:45:46 +0000 (17:45 +0200)]
ARM: dts: Enable Ethernet on STi's B2120 boards
These boards are mounted with Realtek RTL8367 switch.
We consider the bootloader will have intiliazed the switch before jumping into
the kernel, so we declare it as a fixed link.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Arnd Bergmann [Wed, 14 Oct 2015 15:57:03 +0000 (17:57 +0200)]
Merge tag 'samsung-dt-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT updates for v4.4" from Kukjin Kim:
- New board support
: add exynos5250-snow-rev5 DT file to support Snow Rev5+ board
: add exynos5422-odroidxu4 DT file to support Odroid XU4 board
: split exynos5422-odroidxu3-audio DT file from odroidxu3-common
- USE GPIO constants for flags cells for exynos boards
- fix cpu compatible value to 'arm926ej-s' for s3c2416
- add DMA support for serial ports for exynos4
- add suspend opp for exynos4412
- remove regulator-compatible usage for exynos4412-trats2
- enable EC vboot context support for Peach boards
- move display-timings node to DP for exynos5250-arndale, smdk5250 and smdk5420
- for exynos4412-odroid/odroidu3
: unify voltage regulator style and
: remove redundant pinctrl settings
: add pwm-fan node and use it as a colling device
- for exynos5422-odroidxu3
: fix power off method and LEDs
- dt-bindings
: grounded AC0KB pin on S2MPS11
: entry how to use PWM FAN as a cooling device
* tag 'samsung-dt-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (22 commits)
ARM: dts: Use GPIO constants for flags cells in exynos5440 boards
ARM: dts: Use GPIO constants for flags cells in exynos5420/5422/5800 boards
ARM: dts: Use GPIO constants for flags cells in exynos4412 boards
ARM: dts: Use GPIO constants for flags cells in exynos4120 boards
ARM: dts: Use GPIO constants for flags cells in exynos3250 boards
ARM: dts: Enable EC vboot context support on Peach boards
ARM: dts: Remove regulator-compatible usage in exynos4412-trats2
ARM: dts: Move display-timings node from fimd to dp in exynos5250-arndale, smdk5250 and smdk5420
ARM: dts: Add Exynos5250 Snow Rev5+ support on exynos5250-snow-rev5
ARM: dts: Unify voltage regulator style in exynos4412-odroid
ARM: dts: Remove redundant pinctrl settings in exynos4412-odroid
ARM: dts: Fix cpu compatible value for s3c2416
ARM: dts: Add support Odroid XU4 board for exynos5422-odroidxu4
ARM: dts: Split audio configuration to separate exynos5422-odroidxu3-audio
ARM: dts: Fix power off method for exynos5422-odroidxu3-common
dt-bindings: Document grounded ACOKB pin on S2MPS11
ARM: dts: use pwm-fan device as a cooling device for exynos4412-odroidu3
ARM: dts: Add pwm-fan node for exynos4412-odroidu3
dt-bindings: Documentation entry to explain how to use PWM FAN as a cooling device
ARM: dts: add suspend opp to exynos4412
...
Ian Campbell [Mon, 5 Oct 2015 11:53:52 +0000 (12:53 +0100)]
ARM64: dts: vexpress: Use a symlink to vexpress-v2m-rs1.dtsi from arch=arm
Commit 9ccd608070b6 "arm64: dts: add device tree for ARM SMM-A53x2 on
LogicTile Express 20MG" added a new dts file to arch/arm64 which
included "../../../../arm/boot/dts/vexpress-v2m-rs1.dtsi", i.e. a
.dtsi supplied by arch/arm.
Unfortunately this causes some issues for the split device tree
repository[0], since things get moved around there. In that context
the new .dts ends up at src/arm64/arm/vexpress-v2f-1xv7-ca53x2.dts
while the include is at src/arm/vexpress-v2m-rs1.dtsi.
The sharing of the .dtsi is legitimate since the baseboard is the same
for various vexpress systems whatever processor they use.
Previously I attempted to resolve this by creating a shared location
for such things but we have been unable to come to a consensus on
where that should be.
Instead this patch simply replaces the use of ../../ in the dts
/include/ with a symlink in arch/arm64/boot/dts/arm pointing to the
file arch/arm/boot/dts.
Since the split device tree repo will shortly be required to flatten
symlinks for other reasons this will cause the dtsi file to appear in
both src/arm and src/arm64 in the split repo, which is an improvement
on not building for arm64 now.
projects / karo-tx-linux.git / log