Michal Kazior [Fri, 22 Aug 2014 12:33:14 +0000 (14:33 +0200)]
ath10k: rework posting pci rx buffers
It was possible on a host system running low on
memory to end up with no rx buffers on pci pipes.
This makes the driver more robust as it won't fail
to start if it can't allocate all rx buffers right
away. If it is fatal then upper layers will notice
trouble anyway.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Fri, 22 Aug 2014 12:23:34 +0000 (14:23 +0200)]
ath10k: remove early irq handling
It's not really necessary to have a dedicated irq
handler just for the sake of catching early fw
crashes anymore. It is now safe to use one handler
even during early stages of device boot up.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Fri, 22 Aug 2014 12:23:33 +0000 (14:23 +0200)]
ath10k: make sure to really disable irqs
This fixes two corner cases.
One is a race between disabling copy engine
interrupts and unhandled pending interrupts on the
host. This could end up with a runaway tasklet and
consequently memory leak of a few copy engine
rx buffers.
The other one is an unexpected (and non-maskable
via device CSR) MSI fw indication interrupt during
teardown. This could trigger the same problem as
the first corner case.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Fri, 22 Aug 2014 12:23:32 +0000 (14:23 +0200)]
ath10k: split ce irq/handler setup
It doesn't make much sense to overwrite send_cb
and recv_cb callbacks over and over again whenever
transport starts. Just make sure to unmask copy
engine interrupts when starting.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ben Greear [Mon, 25 Aug 2014 05:37:32 +0000 (08:37 +0300)]
ath10k: provide firmware crash info via debugfs
Store the firmware registers and other relevant data to a firmware crash dump
file and provide it to user-space via debugfs. Should help with figuring out
why the firmware crashed.
kvalo: remove dbglog support, rework and refactor the code to avoid ifdefs and
otherwise simplify it as well
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Tue, 19 Aug 2014 11:22:32 +0000 (13:22 +0200)]
ath10k: fix a conflict bug in wmi service bitmap
Service mapping for main firmware branch was incorrectly used for 10.x firmware
and vice-versa. This caused wmi_services in debugfs to print wrong values.
This fixes commit cff990ce7ddd6 ("ath10k: fix wmi service bitmap debug") where
for some reason there was either a conflict that wasn't resolved properly or
git had a bad day.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Simon Wunderlich [Tue, 12 Aug 2014 15:12:17 +0000 (17:12 +0200)]
ath10k: unregister spectral before mac
If spectral is unregistered after mac80211, the relayfs file has already
been removed recursively by mac/cfg80211, and spectral tries to remove
the file once more, thus leading to double free problems. Better clean
up spectral before to avoid that problem.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Thu, 7 Aug 2014 09:03:29 +0000 (11:03 +0200)]
ath10k: remove pci features var
The ATH10K_PCI_FEATURE_MSI_X was originally
introduced to support both chips QCA988Xv1 and
QCA988Xv2. Since v1 isn't supported anymore it
doesn't make sense to keep the feature flag
around. Since this is the last one remove the
whole thing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Thu, 7 Aug 2014 09:03:28 +0000 (11:03 +0200)]
ath10k: remove target soc ps code
The soc powersave was disabled by default. It
never was fully tested. Some hw apparently had
problems with it and the implementation itself had
a possible race.
Just remove the refcounting and simply wake up the
device when probing and put to sleep when
removing.
kvalo: make ath10k_pci_wake() and _sleep() static
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Tue, 5 Aug 2014 12:54:44 +0000 (14:54 +0200)]
ath10k: introduce a stricter scan state machine
This aims at fixing some rare scan bugs related to
firmware reporting unexpected scan event
sequences.
One such bug was if spectral scan phyerr reporting
prevented firmware from properly propagating scan
events to host. This led to scan timeout. After
that next scan would trigger scan completed event
first (before scan started event) leading to
ar->scan.in_progress and timeout timer states to
be overwritten incorrectly and making the very
next scan to hang forever.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Adds the spectral scan feature for ath10k. The spectral scan is triggered by
configuring a mode through a debugfs control file. Samples can be gathered via
another relay debugfs file.
Essentially, to try it out:
ip link set dev wlan0 up
echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 > samples
This feature is still experimental. Based on the original RFC patch of
Sven Eckelmann.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sven Eckelmann [Sat, 2 Aug 2014 06:12:53 +0000 (09:12 +0300)]
ath: Move spectral debugfs structs to shared header
The ath9k and ath10k will share the definitions of the debugfs spectral
structures and enums. Having them in the same place helps to avoid conflicts.
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Mon, 28 Jul 2014 20:59:42 +0000 (23:59 +0300)]
ath10k: fix aggregated 4addr Rx
A-MSDU 4addr frames weren't reconstructed properly
and in some cases this resulted in a warning:
br0: received packet on wlan0.sta1 with own address as source address
Since this was only related to A-MSDU it would
trigger when more intense traffic was generated.
Reported-by: Vu Hai NGUYEN <vh.nguyen@actiasodielec.fr> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Fri, 25 Jul 2014 11:32:17 +0000 (13:32 +0200)]
ath10k: add support for 10.2 firmware
The 10.2 firmware is a successor of 10.1 firmware
(formerly identified as 10.x). Both share a lot
but have some slight ABI differences that need to
be taken care of.
The 10.2 firmware introduces some new features but
those can be added in subsequent patches. This
patch makes ath10k boot and work with 10.2 with
comparable functionality to 10.1.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Janusz Dziedzic [Fri, 25 Jul 2014 08:28:50 +0000 (11:28 +0300)]
ath10k: handle attention flags correctly when using A-MSDU
In case of A-MSDU RX we should check attention flags
correctly to be sure we report correct FCS status for
A-MSDU subframes. Without a patch we could report A-MSDU
subframes with wrong FCS as a correct to the stack, next
get a lot of DUP ACK TCP packets. Finally TP drop is seen
and this drop depends on FCS errors ratio for A-MSDU frame.
Example test case when TP drop is seen:
- ath10k configured as an AP
- used ath10k station
- forced A-MSDU (7 frames) on STA
- other traffic on channel (often FCS errors)
- monitor iface added on AP
- TCP STA -> AP traffic (iperf)
Reported-by: Denton Gentry <denton.gentry@gmail.com> Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Wed, 23 Jul 2014 10:20:33 +0000 (12:20 +0200)]
ath10k: fix Rx aggregation reordering
Firmware doesn't perform Rx reordering so it is
left to the host driver to do that.
Use mac80211 to perform reordering instead of
re-inventing the wheel.
This fixes TCP throughput issues in some
environments.
Reported-by: Denton Gentry <denton.gentry@gmail.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This has been tested on 14e4:4328 (BCM4321), 14e4:432b (BCM4322),
14e4:4353 (BCM43224) and 14e4:4359 (BCM43228) which is an almost
complete list of 5 GHz capable device (only BCM43222 is missing).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The dividend in do_div() is expected to be an unsigned 64-bit integer,
which leads to the following warning when building for 32-bit MIPS:
drivers/net/wireless/mac80211_hwsim.c: In function 'mac80211_hwsim_set_tsf':
drivers/net/wireless/mac80211_hwsim.c:664:98: warning: comparison of distinct pointer types lacks a cast [enabled by default]
data->bcn_delta = do_div(delta, bcn_int);
Since we care about the signedness of delta when adjusting tsf_offset
and bcm_delta, use the absolute value for the division and compare
the two timestamps to determine the sign.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arik Nemtsov [Sun, 15 Jun 2014 13:03:55 +0000 (16:03 +0300)]
iwlwifi: mvm: teardown TDLS peers during chan-switch and AP DCM
The DCM condition was not checked well for channel switch in both AP and
station scenarios. Teardown was also not done for AP/GO DCM. Add the
missing checks.
Michal Kazior [Mon, 21 Jul 2014 18:03:10 +0000 (21:03 +0300)]
ath10k: prevent endless pci rx loop
It was possible to enter an endless loop while
processing a single pci copy engine pipe. This
could effectively render ath10k incapable of
responding to any requests.
An example case when this could happen is when
firmware generates a lot of events, e.g. spectral
scan phyerr via WMI.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add some missing ops and prepare for new devices support. This patch is
a great stability improvement for BCM43217. Earlier Tenda W322E used to
disconnect every 2 minutes (16 times over 30 minutes). With this fix I
got it running for 4 hours (with iperf) without any disconnection.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: mvm: reset beacon filtering and BT Coex data upon FW restart
When the firmware asserts, we restart the device and reset
the relevant data we hold in the driver. BT Coex data was
not reset and because of that, the driver wouldn't
reconfigure the firmware properly after firmware restart.
Same for beacon filtering. Fix that.
Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eran Harary [Tue, 15 Jul 2014 11:04:23 +0000 (14:04 +0300)]
iwlwifi: mvm: update smart fifo / beacon filtering upon association
When we associate, we may have heard the beacon before the
association. In that case, BSS_CHANGED_BEACON_INFO will be
set along with BSS_CHANGED_ASSOC in changes in
bss_info_change.
In this case, we didn't update the smart fifo nor beacon
filtering leaving those two feature disabled.
Signed-off-by: Eran Harary <eran.harary@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwlwifi: split fw-error-dump between transport and mvm
The mvm op_mode won't allocate the buffer for the transport
any more. The transport allocates its own buffer and mvm
is in charge of splicing the buffers in the debugfs hook.
This makes the repartition easier to handle.
Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
According to new requirements, the ACK / CTS kill mask is
not related to reduced TX power anymore. This allows to
remove the code that tracked reduced TX power enablement
across different interfaces.
The ACK / CTS kill mask is now fetch from a table. It
depends on the Activity grading (activity from BT) and on
the Look Up Table (LUT) type.
The Remain On Channel framework added to the firmare is
a bit like time events. It allows the driver to request
the firmware to be on a certain channel for a certain time.
Unlike the time events, the ROC infrastructure doesn't need
a MAC context in the firmware - it uses a generic context
called "auxiliary framework".
This is useful for any offchannel activity that is not bound
to a specific MAC.
The flow is synchronized much like with time events:
1) The driver receives an action frame from the wpa_supplicant
via nl80211 that requests to be sent offchannel.
2) The driver sends an Aux ROC command (0x53) to the firmware.
3) The firmware responds with the unique id of the time event.
4) When time event starts, the driver puts the frame in the
Aux queue.
Special care needs to be taken when the time events ends:
the queue needs to be cleaned-up.
Michal Kazior [Mon, 21 Jul 2014 18:03:10 +0000 (21:03 +0300)]
ath10k: workaround qos nullfunc bug
Apparently fw/hw generates a corrupted QoS Control
Field in Qos NullFunc frames. The only way to
workaround this is to downgrade frames to
NullFunc. This should be okay since powersave is
done by fw/hw and these frames are only used for
CQM purposes (e.g. from hostapd to check if
station is still connected).
This doesn't fix any user visible bug that I know
of. It just prevents from sending out funky frames
on the air.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Mon, 21 Jul 2014 18:03:09 +0000 (21:03 +0300)]
ath10k: simplify tx helpers
It always bugged me how tid is computed and stored
in a temporary var before written to the control
buffer. It was confusing and it made it difficult
to work with tx helpers.
While at it rename the qos workaround function as
it was misleading - it's not a workaround but
preparation for nwifi tx mode.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Mon, 21 Jul 2014 17:52:59 +0000 (20:52 +0300)]
ath10k: prevent some tx flushing failures
Firmware could request inspection of some
submitted tx requests. Since the callback wasn't
implemented it was possible to bleed tx msdu_ids
which could translate to tx flushing timeouts.
There's nothing ath10k can do to help firmware
with tx processing now so just report all tx
frames as already inspected to prevent firmware
from sending up inspection events and force it to
report regular tx completion indications with
discard status.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Wed, 16 Jul 2014 13:01:39 +0000 (15:01 +0200)]
ath10k: workaround boot issues with KVM/PCI-passthrough
Apparently iomap writes that unmask CE irqs aren't
propagated properly sometimes. Before failing try
to poll for the control response message as it may
have been delivered without an interrupt.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Wed, 16 Jul 2014 10:12:15 +0000 (12:12 +0200)]
mac80211: add support for Rx reordering offloading
Some drivers may be performing most of Tx/Rx
aggregation on their own (e.g. in firmware)
including AddBa/DelBa negotiations but may
otherwise require Rx reordering assistance.
The patch exports 2 new functions for establishing
Rx aggregation sessions in assumption device
driver has taken care of the necessary
negotiations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[fix endian bug] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 16 Jul 2014 10:09:31 +0000 (12:09 +0200)]
mac80211: fix Rx reordering with RX_FLAG_AMSDU_MORE
Some drivers (e.g. ath10k) report A-MSDU subframes
individually with identical seqno. The A-MPDU Rx
reorder code did not account for that which made
it practically unusable with drivers using
RX_FLAG_AMSDU_MORE because it would end up
dropping a lot of frames resulting in confusion in
upper network transport layers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sdata can't be NULL, and key being NULL is really not possible
unless the code is modified.
The sdata check made a static analyze (klocwork) unhappy because
we would get pointer to local (sdata->local) and only then check
if sdata is non-NULL.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove !key check as well] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bluetooth: Add support for Broadcom device of Asus Z97-DELUXE motherboard
The Asus Z97-DELUXE motherboard contains a Broadcom based Bluetooth
controller on the USB bus. However vendor and product ID are listed
as ASUSTek Computer.
Johan Hedberg [Mon, 21 Jul 2014 07:50:06 +0000 (10:50 +0300)]
Bluetooth: Prefer sizeof(*ptr) when allocating memory
It's safer practice to use sizeof(*ptr) instead of sizeof(ptr_type) when
allocating memory in case the type changes. This also fixes the
following style of warnings from static analyzers:
Max Stepanov [Wed, 9 Jul 2014 13:55:32 +0000 (16:55 +0300)]
mac80211: fix a potential NULL access in ieee80211_crypto_hw_decrypt
The NULL pointer access could happen when ieee80211_crypto_hw_decrypt
is called from ieee80211_rx_h_decrypt with the following condition:
1. rx->key->conf.cipher is not WEP, CCMP, TKIP or AES_CMAC
2. rx->sta is NULL
When ieee80211_crypto_hw_decrypt is called, it verifies
rx->sta->cipher_scheme and it will cause Oops if rx->sta is NULL.
This path adds an addirional rx->sta == NULL verification in
ieee80211_crypto_hw_decrypt for this case.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wireless: fixup genregdb.awk for remove of antenna gain from wireless-regd
Since "wireless-regdb: remove antenna gain" was merged in the
wireless-regdb tree, the awk script parser has been incompatible
with the 'official' regulatory database. This fixes that up.
Without this change the max EIRP is set to 0 making 802.11 devices
useless.
The fragile nature of the awk parser must be replaced, but ideas
over how to do that in the most scalable way are being reviewed.
In the meantime update the documentation for CFG80211_INTERNAL_REGDB
so folks are aware of expectations for now.
Reported-by: John Walker <john@x109.net> Reported-by: Krishna Chaitanya <chaitanya.mgit@gmail.com> Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211: remove redundant IEEE80211_STA_CSA_RECEIVED flag
The csa_active flag was added in sdata a while ago and made
IEEE80211_STA_CSA_RECEIVED redundant. The new flag is also used to
mark when CSA is ongoing on other iftypes and took over the old one as
the preferred method for checking whether we're in the middle of a
channel switch. Remove the old, redundant flag.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211: make sure TDLS teardown packet is sent on time
Since the teardown packet is created while the queues are
stopped, it isn't sent immediately, but rather is pending.
To be sure that when we flush the queues prior to destroying
the station we also send this packet - the tasklet handling
pending packets is invoked to flush the packets.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com> Reviewed-by: ArikX Nemtsov <arik@wizery.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211: ignore frames between TDLS peers when operating as AP
If the AP receives actions frames destined for other peers, it may
mistakenly toggle BA-sessions from itself to a peer.
Ignore TDLS data packets as well - the AP should not handle them.
Some VHT TDLS peers (Google Nexus 5) include the VHT-AID IE in their
TDLS setup request/response. Usermode passes this aid as the station
aid, causing it to fail verifiction, since this happens in the
"set_station" stage. Make an exception for the TDLS use-case.
TDLS VHT support requires some more information elements during setup.
While these are not there, mask out the peer's VHT capabilities so that
VHT rates are not mistakenly used.
We can only be a station for TDLS connections. Also fix a bug where
a delayed work could be left scheduled if the station interface was
brought down during TDLS setup.
When TDLS QoS is supported by the the peer and the local card, add
the WMM parameter IE to the setup-confirm frame. Take the QoS settings
from the current AP, or if unsupported, use the default values from
the specification. This behavior is mandated by IEEE802.11-2012 section
10.22.4.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Liad Kaufman <liad.kaufman@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The patch "8f02e6b mac80211: make sure TDLS peer STA exists during
setup" broke TDLS error paths where the STA doesn't exist when sending
the error.
Fix it by only testing for STA existence during a non-error flow.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Infer the TDLS initiator and track it in mac80211 via a STA flag. This
avoids breaking old userspace that doesn't pass it via nl80211 APIs.
The only case where userspace will need to pass the initiator is when the
STA is removed due to unreachability before a teardown packet is sent.
Support for unreachability was only recently added to wpa_supplicant, so
it won't be a problem in practice.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
projects / linux-beck.git / log