Chaitanya T K [Wed, 10 Jun 2015 13:42:31 +0000 (19:12 +0530)]
mac80211: wowlan: enable powersave if suspend while ps-polling
If for any reason we're in the middle of PS-polling or awake after
TX due to dynamic powersave while going to suspend, go back to save
power. This might cause a response frame to get lost, but since we
can't really wait for it while going to suspend that's still better
than not enabling powersave which would cause higher power usage
during (and possibly even after) suspend.
Note that this really only affects the very few drivers that use
the powersave implementation in mac80211.
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
[rewrite misleading commit log] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Thu, 2 Jul 2015 07:59:56 +0000 (09:59 +0200)]
mac80211: don't clear all tx flags when requeing
When acting as AP and a PS-Poll frame is received
associated station is marked as one in a Service
Period. This state is kept until Tx status for
released frame is reported. While a station is in
Service Period PS-Poll frames are ignored.
However if PS-Poll was received during A-MPDU
teardown it was possible to have the to-be
released frame re-queued back to pending queue.
In such case the frame was stripped of 2 important
flags:
Stripping of (a) led to the frame that was to be
released to be queued back to ps_tx_buf queue. If
station remained to use only PS-Poll frames the
re-queued frame (and new ones) was never actually
transmitted because mac80211 would ignore
subsequent PS-Poll frames due to station being in
Service Period. There was nothing left to clear
the Service Period bit (no xmit -> no tx status ->
no SP end), i.e. the AP would have the station
stuck in Service Period. Beacon TIM would
repeatedly prompt station to poll for frames but
it would get none.
Once (a) is not stripped (b) becomes important
because it's the main condition to clear the
Service Period bit of the station when Tx status
for the released frame is reported back.
This problem was observed with ath9k acting as P2P
GO in some testing scenarios but isn't limited to
it. AP operation with mac80211 based Tx A-MPDU
control combined with clients using PS-Poll frames
is subject to this race.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tom Hughes [Mon, 29 Jun 2015 18:41:49 +0000 (19:41 +0100)]
mac80211: clear subdir_stations when removing debugfs
If we don't do this, and we then fail to recreate the debugfs
directory during a mode change, then we will fail later trying
to add stations to this now bogus directory:
1) Missing list head init in bluetooth hidp session creation, from Tedd
Ho-Jeong An.
2) Don't leak SKB in bridge netfilter error paths, from Florian
Westphal.
3) ipv6 netdevice private leak in netfilter bridging, fixed by Julien
Grall.
4) Fix regression in IP over hamradio bpq encapsulation, from Ralf
Baechle.
5) Fix race between rhashtable resize events and table walks, from Phil
Sutter.
6) Missing validation of IFLA_VF_INFO netlink attributes, fix from
Daniel Borkmann.
7) Missing security layer socket state initialization in tipc code,
from Stephen Smalley.
8) Fix shared IRQ handling in boomerang 3c59x interrupt handler, from
Denys Vlasenko.
9) Missing minor_idr destroy on module unload on macvtap driver, from
Johannes Thumshirn.
10) Various pktgen kernel thread races, from Oleg Nesterov.
11) Fix races that can cause packets to be processed in the backlog even
after a device attached to that SKB has been fully unregistered.
From Julian Anastasov.
12) bcmgenet driver doesn't account packet drops vs. errors properly,
fix from Petri Gynther.
13) Array index validation and off by one fix in DSA layer from Florian
Fainelli
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (66 commits)
can: replace timestamp as unique skb attribute
ARM: dts: dra7x-evm: Prevent glitch on DCAN1 pinmux
can: c_can: Fix default pinmux glitch at init
can: rcar_can: unify error messages
can: rcar_can: print request_irq() error code
can: rcar_can: fix typo in error message
can: rcar_can: print signed IRQ #
can: rcar_can: fix IRQ check
net: dsa: Fix off-by-one in switch address parsing
net: dsa: Test array index before use
net: switchdev: don't abort unsupported operations
net: bcmgenet: fix accounting of packet drops vs errors
cdc_ncm: update specs URL
Doc: z8530book: Fix typo in API-z8530-sync-txdma-open.html
net: inet_diag: always export IPV6_V6ONLY sockopt for listening sockets
bridge: mdb: allow the user to delete mdb entry if there's a querier
net: call rcu_read_lock early in process_backlog
net: do not process device backlog during unregistration
bridge: fix potential crash in __netdev_pick_tx()
net: axienet: Fix devm_ioremap_resource return value check
...
Pull crypto fixes from Herbert Xu:
"This fixes a duplicate dma_unmap_sg call in omap-des and reentrancy
bugs in the powerpc nx driver which may cause bogus output or worse
memory corruption"
David S. Miller [Mon, 13 Jul 2015 05:24:01 +0000 (22:24 -0700)]
Merge tag 'linux-can-fixes-for-4.2-20150712' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-07-12
this is a pull request of 8 patchs for net/master.
Sergei Shtylyov contributes 5 patches for the rcar_can driver, fixing the IRQ
check and several info and error messages. There are two patches by J.D.
Schroeder and Roger Quadros for the c_can driver and dra7x-evm device tree,
which precent a glitch in the DCAN1 pinmux. Oliver Hartkopp provides a better
approach to make the CAN skbs unique, the timestamp is replaced by a counter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
So the change to test 'crtc_state->base.active' cannot possibly be
correct as-is.
There may be some other minimal fix (like just checking crtc_state for
NULL), but I'm just reverting it now for the rc2 release, and people
like Daniel Vetter who actually know this code will figure out what the
right solution is in the longer term.
Reported-and-bisected-by: Jörg Otte <jrg.otte@gmail.com> Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@intel.com> CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull VFS fixes from Al Viro:
"Fixes for this cycle regression in overlayfs and a couple of
long-standing (== all the way back to 2.6.12, at least) bugs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
freeing unlinked file indefinitely delayed
fix a braino in ovl_d_select_inode()
9p: don't leave a half-initialized inode sitting around
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"A fair number of 4.2 fixes also because Markos opened the flood gates.
- Patch up the math used calculate the location for the page bitmap.
- The FDC (Not what you think, FDC stands for Fast Debug Channel) IRQ
around was causing issues on non-Malta platforms, so move the code
to a Malta specific location.
- A spelling fix replicated through several files.
- Fix to the emulation of an R2 instruction for R6 cores.
- Fix the JR emulation for R6.
- Further patching of mindless 64 bit issues.
- Ensure the kernel won't crash on CPUs with L2 caches with >= 8
ways.
- Use compat_sys_getsockopt for O32 ABI on 64 bit kernels.
- Fix cache flushing for multithreaded cores.
- A build fix"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: O32: Use compat_sys_getsockopt.
MIPS: c-r4k: Extend way_string array
MIPS: Pistachio: Support CDMM & Fast Debug Channel
MIPS: Malta: Make GIC FDC IRQ workaround Malta specific
MIPS: c-r4k: Fix cache flushing for MT cores
Revert "MIPS: Kconfig: Disable SMP/CPS for 64-bit"
MIPS: cps-vec: Use macros for various arithmetics and memory operations
MIPS: kernel: cps-vec: Replace KSEG0 with CKSEG0
MIPS: kernel: cps-vec: Use ta0-ta3 pseudo-registers for 64-bit
MIPS: kernel: cps-vec: Replace mips32r2 ISA level with mips64r2
MIPS: kernel: cps-vec: Replace 'la' macro with PTR_LA
MIPS: kernel: smp-cps: Fix 64-bit compatibility errors due to pointer casting
MIPS: Fix erroneous JR emulation for MIPS R6
MIPS: Fix branch emulation for BLTC and BGEC instructions
MIPS: kernel: traps: Fix broken indentation
MIPS: bootmem: Don't use memory holes for page bitmap
MIPS: O32: Do not handle require 32 bytes from the stack to be readable.
MIPS, CPUFREQ: Fix spelling of Institute.
MIPS: Lemote 2F: Fix build caused by recent mass rename.
Oliver Hartkopp [Fri, 26 Jun 2015 09:58:19 +0000 (11:58 +0200)]
can: replace timestamp as unique skb attribute
Commit 514ac99c64b "can: fix multiple delivery of a single CAN frame for
overlapping CAN filters" requires the skb->tstamp to be set to check for
identical CAN skbs.
Without timestamping to be required by user space applications this timestamp
was not generated which lead to commit 36c01245eb8 "can: fix loss of CAN frames
in raw_rcv" - which forces the timestamp to be set in all CAN related skbuffs
by introducing several __net_timestamp() calls.
This forces e.g. out of tree drivers which are not using alloc_can{,fd}_skb()
to add __net_timestamp() after skbuff creation to prevent the frame loss fixed
in mainline Linux.
This patch removes the timestamp dependency and uses an atomic counter to
create an unique identifier together with the skbuff pointer.
Btw: the new skbcnt element introduced in struct can_skb_priv has to be
initialized with zero in out-of-tree drivers which are not using
alloc_can{,fd}_skb() too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Roger Quadros [Tue, 7 Jul 2015 14:27:57 +0000 (17:27 +0300)]
ARM: dts: dra7x-evm: Prevent glitch on DCAN1 pinmux
Driver core sets "default" pinmux on on probe and CAN driver
sets "sleep" pinmux during register. This causes a small window
where the CAN pins are in "default" state with the DCAN module
being disabled.
Change the "default" state to be like sleep so this glitch is
avoided. Add a new "active" state that is used by the driver
when CAN is actually active.
Signed-off-by: Roger Quadros <rogerq@ti.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The previous change 3973c526ae9c (net: can: c_can: Disable pins when CAN
interface is down) causes a slight glitch on the pinctrl settings when used.
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
the device core will automatically set the default pins. This causes the pins
to be momentarily set to the default and then to the sleep state in
register_c_can_dev(). By adding an optional "enable" state, boards can set the
default pin state to be disabled and avoid the glitch when the switch from
default to sleep first occurs. If the "enable" state is not available
c_can_pinctrl_select_state() falls back to using the "default" pinctrl state.
[Roger Q] - Forward port to v4.2 and use pinctrl_get_select().
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sergei Shtylyov [Sat, 20 Jun 2015 00:34:55 +0000 (03:34 +0300)]
can: rcar_can: fix typo in error message
Fix typo in the first error message printed by rcar_can_open().
Based on the original patch by Vladimir Barinov.
Fixes: 862e2b6af941 ("can: rcar_can: support all input clocks") Reported-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sergei Shtylyov [Sat, 20 Jun 2015 00:32:46 +0000 (03:32 +0300)]
can: rcar_can: fix IRQ check
rcar_can_probe() regards 0 as a wrong IRQ #, despite platform_get_irq() that it
calls returns negative error code in that case. This leads to the following
being printed to the console when attempting to open the device:
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
- the high latency PIT detection fix, which slipped through the cracks
for rc1
- a regression fix for the early printk mechanism
- the x86 part to plug irq/vector related hotplug races
- move the allocation of the espfix pages on cpu hotplug to non atomic
context. The current code triggers a might_sleep() warning.
- a series of KASAN fixes addressing boot crashes and usability
- a trivial typo fix for Kconfig help text
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kconfig: Fix typo in the CONFIG_CMDLINE_BOOL help text
x86/irq: Retrieve irq data after locking irq_desc
x86/irq: Use proper locking in check_irq_vectors_for_cpu_disable()
x86/irq: Plug irq vector hotplug race
x86/earlyprintk: Allow early_printk() to use console style parameters like '115200n8'
x86/espfix: Init espfix on the boot CPU side
x86/espfix: Add 'cpu' parameter to init_espfix_ap()
x86/kasan: Move KASAN_SHADOW_OFFSET to the arch Kconfig
x86/kasan: Add message about KASAN being initialized
x86/kasan: Fix boot crash on AMD processors
x86/kasan: Flush TLBs after switching CR3
x86/kasan: Fix KASAN shadow region page tables
x86/init: Clear 'init_level4_pgt' earlier
x86/tsc: Let high latency PIT fail fast in quick_pit_calibrate()
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"This update from the timer departement contains:
- A series of patches which address a shortcoming in the tick
broadcast code.
If the broadcast device is not available or an hrtimer emulated
broadcast device, some of the original assumptions lead to boot
failures. I rather plugged all of the corner cases instead of only
addressing the issue reported, so the change got a little larger.
Has been extensivly tested on x86 and arm.
- Get rid of the last holdouts using do_posix_clock_monotonic_gettime()
- A regression fix for the imx clocksource driver
- An update to the new state callbacks mechanism for clockevents.
This is required to simplify the conversion, which will take place
in 4.3"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/broadcast: Prevent NULL pointer dereference
time: Get rid of do_posix_clock_monotonic_gettime
cris: Replace do_posix_clock_monotonic_gettime()
tick/broadcast: Unbreak CONFIG_GENERIC_CLOCKEVENTS=n build
tick/broadcast: Handle spurious interrupts gracefully
tick/broadcast: Check for hrtimer broadcast active early
tick/broadcast: Return busy when IPI is pending
tick/broadcast: Return busy if periodic mode and hrtimer broadcast
tick/broadcast: Move the check for periodic mode inside state handling
tick/broadcast: Prevent deep idle if no broadcast device available
tick/broadcast: Make idle check independent from mode and config
tick/broadcast: Sanity check the shutdown of the local clock_event
tick/broadcast: Prevent hrtimer recursion
clockevents: Allow set-state callbacks to be optional
clocksource/imx: Define clocksource for mx27
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single fix for a cpu hotplug race vs. interrupt descriptors:
Prevent irq setup/teardown across the cpu starting/dying parts of cpu
hotplug so that the starting/dying cpu has a stable view of the
descriptor space. This has been an issue for all architectures in the
cpu dying phase, where interrupts are migrated away from the dying
cpu. In the starting phase its mostly a x86 issue vs the vector space
update"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hotplug: Prevent alloc/free of irq descriptors during cpu up/down
Al Viro [Wed, 8 Jul 2015 01:42:38 +0000 (02:42 +0100)]
freeing unlinked file indefinitely delayed
Normally opening a file, unlinking it and then closing will have
the inode freed upon close() (provided that it's not otherwise busy and
has no remaining links, of course). However, there's one case where that
does *not* happen. Namely, if you open it by fhandle with cold dcache,
then unlink() and close().
In normal case you get d_delete() in unlink(2) notice that dentry
is busy and unhash it; on the final dput() it will be forcibly evicted from
dcache, triggering iput() and inode removal. In this case, though, we end
up with *two* dentries - disconnected (created by open-by-fhandle) and
regular one (used by unlink()). The latter will have its reference to inode
dropped just fine, but the former will not - it's considered hashed (it
is on the ->s_anon list), so it will stay around until the memory pressure
will finally do it in. As the result, we have the final iput() delayed
indefinitely. It's trivial to reproduce -
main()
{
int fd;
union {
struct file_handle f;
char buf[MAX_HANDLE_SZ];
} x;
int m;
x.f.handle_bytes = sizeof(x);
chdir("/root");
mkdir("foo", 0700);
fd = open("foo/bar", O_CREAT | O_RDWR, 0600);
close(fd);
name_to_handle_at(AT_FDCWD, "foo/bar", &x.f, &m, 0);
flush_dcache();
fd = open_by_handle_at(AT_FDCWD, &x.f, O_RDWR);
unlink("foo/bar");
write(fd, buf, sizeof(buf));
system("df ."); /* 20Mb eaten */
close(fd);
system("df ."); /* should've freed those 20Mb */
flush_dcache();
system("df ."); /* should be the same as #2 */
}
will spit out something like
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 303843 1131 100% /
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 303843 1131 100% /
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 283282 21692 93% /
- inode gets freed only when dentry is finally evicted (here we trigger
than by remount; normally it would've happened in response to memory
pressure hell knows when).
Cc: stable@vger.kernel.org # v2.6.38+; earlier ones need s/kill_it/unhash_it/ Acked-by: J. Bruce Fields <bfields@fieldses.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 12 Jul 2015 14:39:45 +0000 (10:39 -0400)]
fix a braino in ovl_d_select_inode()
when opening a directory we want the overlayfs inode, not one from
the topmost layer.
Reported-By: Andrey Jr. Melnikov <temnota.am@gmail.com> Tested-By: Andrey Jr. Melnikov <temnota.am@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
David S. Miller [Sun, 12 Jul 2015 06:25:16 +0000 (23:25 -0700)]
Merge branch 'dsa-of-parsing-fixes'
Florian Fainelli says:
====================
net: dsa: OF parsing fixes
This patch series fixes two small parsing issues, the first one was
reported by Dan, the second came after looking more closely at the
code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: Fix off-by-one in switch address parsing
cd->sw_addr is used as a MDIO bus address, which cannot exceed
PHY_MAX_ADDR (32), our check was off-by-one.
Fixes: 5e95329b701c ("dsa: add device tree bindings to register DSA switches") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
port_index is used an index into an array, and this information comes
from Device Tree, make sure that port_index is not equal to the array
size before using it. Move the check against port_index earlier in the
loop.
Fixes: 5e95329b701c: ("dsa: add device tree bindings to register DSA switches") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to abort attribute setting or object addition, if the
prepare phase returned operation not supported.
Thus, abort these two transactions only if the error is not -EOPNOTSUPP.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Scott Feldman <sfeldma@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm
Pull libnvdimm fixes from Dan Williams:
"1) Fixes for a handful of smatch reports (Thanks Dan C.!) and minor
bug fixes (patches 1-6)
2) Correctness fixes to the BLK-mode nvdimm driver (patches 7-10).
Granted these are slightly large for a -rc update. They have been
out for review in one form or another since the end of May and were
deferred from the merge window while we settled on the "PMEM API"
for the PMEM-mode nvdimm driver (ie memremap_pmem, memcpy_to_pmem,
and wmb_pmem).
Now that those apis are merged we implement them in the BLK driver
to guarantee that mmio aperture moves stay ordered with respect to
incoming read/write requests, and that writes are flushed through
those mmio-windows and platform-buffers to be persistent on media.
These pass the sub-system unit tests with the updates to
tools/testing/nvdimm, and have received a successful build-report from
the kbuild robot (468 configs).
With acks from Rafael for the touches to drivers/acpi/"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm:
nfit: add support for NVDIMM "latch" flag
nfit: update block I/O path to use PMEM API
tools/testing/nvdimm: add mock acpi_nfit_flush_address entries to nfit_test
tools/testing/nvdimm: fix return code for unimplemented commands
tools/testing/nvdimm: mock ioremap_wt
pmem: add maintainer for include/linux/pmem.h
nfit: fix smatch "use after null check" report
nvdimm: Fix return value of nvdimm_bus_init() if class_create() fails
libnvdimm: smatch cleanups in __nd_ioctl
sparse: fix misplaced __pmem definition
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Mostly slight adjusments for new drivers, but also one core fix for
which finally the dependencies are now available as well"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: Mark instantiated device nodes with OF_POPULATE
i2c: jz4780: Fix return value if probe fails
i2c: xgene-slimpro: Fix missing mbox_free_channel call in probe error path
i2c: I2C_MT65XX should depend on HAS_DMA
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A fix (revert) for a recent regression in Synaptics driver and a fix
for Elan i2c touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - allocate 3 slots to keep stability in image sensors"
Input: elan_i2c - change the hover event from MT to ST
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A small set of fixes for problems found by smatch in new drivers that
we added this rc and a handful of driver fixes that came in during the
merge window"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
drivers: clk: st: Incorrect register offset used for lock_status
clk: mediatek: mt8173: Fix enabling of critical clocks
drivers: clk: st: Fix mux bit-setting for Cortex A9 clocks
drivers: clk: st: Add CLK_GET_RATE_NOCACHE flag to clocks
drivers: clk: st: Fix flexgen lock init
drivers: clk: st: Fix FSYN channel values
drivers: clk: st: Remove unused code
clk: qcom: Use parent rate when set rate to pixel RCG clock
clk: at91: do not leak resources
clk: stm32: Fix out-by-one error path in the index lookup
clk: iproc: fix bit manipulation arithmetic
clk: iproc: fix memory leak from clock name
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A bunch of fixes for radeon, intel, omap and one amdkfd fix.
Radeon fixes are all over, but it does fix some cursor corruption
across suspend/resume. i915 should fix the second warn you were
seeing, so let us know if not. omap is a bunch of small fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (28 commits)
drm/radeon: disable vce init on cayman (v2)
drm/amdgpu: fix timeout calculation
drm/radeon: check if BO_VA is set before adding it to the invalidation list
drm/radeon: allways add the VM clear duplicate
Revert "Revert "drm/radeon: dont switch vt on suspend""
drm/radeon: Fold radeon_set_cursor() into radeon_show_cursor()
drm/radeon: unpin cursor BOs on suspend and pin them again on resume (v2)
drm/radeon: Clean up reference counting and pinning of the cursor BOs
drm/amdkfd: validate pdd where it acquired first
Revert "drm/i915: Allocate context objects from stolen"
drm/i915: Declare the swizzling unknown for L-shaped configurations
drm/radeon: fix underflow in r600_cp_dispatch_texture()
drm/radeon: default to 2048 MB GART size on SI+
drm/radeon: fix HDP flushing
drm/radeon: use RCU query for GEM_BUSY syscall
drm/amdgpu: Handle irqs only based on irq ring, not irq status regs.
drm/radeon: Handle irqs only based on irq ring, not irq status regs.
drm/i915: Use crtc_state->active in primary check_plane func
drm/i915: Check crtc->active in intel_crtc_disable_planes
drm/i915: Restore all GGTT VMAs on resume
...
Merge branch 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull selinux fixes from James Morris.
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: fix mprotect PROT_EXEC regression caused by mm change
selinux: don't waste ebitmap space when importing NetLabel categories
Merge branch 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This is an assortment of fixes. Most of the commits are from Filipe
(fsync, the inode allocation cache and a few others). Mark kicked in
a series fixing corners in the extent sharing ioctls, and everyone
else fixed up on assorted other problems"
* 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix wrong check for btrfs_force_chunk_alloc()
Btrfs: fix warning of bytes_may_use
Btrfs: fix hang when failing to submit bio of directIO
Btrfs: fix a comment in inode.c:evict_inode_truncate_pages()
Btrfs: fix memory corruption on failure to submit bio for direct IO
btrfs: don't update mtime/ctime on deduped inodes
btrfs: allow dedupe of same inode
btrfs: fix deadlock with extent-same and readpage
btrfs: pass unaligned length to btrfs_cmp_data()
Btrfs: fix fsync after truncate when no_holes feature is enabled
Btrfs: fix fsync xattr loss in the fast fsync path
Btrfs: fix fsync data loss after append write
Btrfs: fix crash on close_ctree() if cleaner starts new transaction
Btrfs: fix race between caching kthread and returning inode to inode cache
Btrfs: use kmem_cache_free when freeing entry in inode cache
Btrfs: fix race between balance and unused block group deletion
btrfs: add error handling for scrub_workers_get()
btrfs: cleanup noused initialization of dev in btrfs_end_bio()
btrfs: qgroup: allow user to clear the limitation on qgroup
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"A fairly random colletion of fixes based on -rc1 for OMAP, sunxi and
prima2 as well as a few arm64-specific DT fixes.
This series also includes a late to support a new Allwinner (sunxi)
SoC, but since it's rather simple and isolated to the
platform-specific code, it's included it for this -rc"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dts: add device tree for ARM SMM-A53x2 on LogicTile Express 20MG
arm: dts: vexpress: add missing CCI PMU device node to TC2
arm: dts: vexpress: describe all PMUs in TC2 dts
GICv3: Add ITS entry to THUNDER dts
arm64: dts: Add poweroff button device node for APM X-Gene platform
ARM: dts: am4372.dtsi: disable rfbi
ARM: dts: am57xx-beagle-x15: Provide supply for usb2_phy2
ARM: dts: am4372: Add emif node
Revert "ARM: dts: am335x-boneblack: disable RTC-only sleep"
ARM: sunxi: Enable simplefb in the defconfig
ARM: Remove deprecated symbol from defconfig files
ARM: sunxi: Add Machine support for A33
ARM: sunxi: Introduce Allwinner H3 support
Documentation: sunxi: Update Allwinner SoC documentation
ARM: prima2: move to use REGMAP APIs for rtciobrg
ARM: dts: atlas7: add pinctrl and gpio descriptions
ARM: OMAP2+: Remove unnessary return statement from the void function, omap2_show_dma_caps
memory: omap-gpmc: Fix parsing of devices
Thomas Gleixner [Sat, 11 Jul 2015 12:26:34 +0000 (14:26 +0200)]
tick/broadcast: Prevent NULL pointer dereference
Dan reported that the recent changes to the broadcast code introduced
a potential NULL dereference.
Add the proper check.
Fixes: e0454311903d "tick/broadcast: Sanity check the shutdown of the local clock_event" Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Doc: z8530book: Fix typo in API-z8530-sync-txdma-open.html
This patch fix a spelling typo found in API-z8530-sync-txdma-open.html.
It is because this file was generated from comment in source,
I have to fix comment in source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter [Fri, 10 Jul 2015 09:39:57 +0000 (11:39 +0200)]
net: inet_diag: always export IPV6_V6ONLY sockopt for listening sockets
Reconsidering my commit 20462155 "net: inet_diag: export IPV6_V6ONLY
sockopt", I am not happy with the limitations it causes for socket
analysing code in userspace. Exporting the value only if it is set makes
it hard for userspace to decide whether the option is not set or the
kernel does not support exporting the option at all.
>From an auditor's perspective, the interesting question for listening
AF_INET6 sockets is: "Does it NOT have IPV6_V6ONLY set?" Because it is
the unexpected case. This patch allows to answer this question reliably.
Signed-off-by: Phil Sutter <phil@nwl.cc> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: mdb: allow the user to delete mdb entry if there's a querier
Until now when a querier was present static entries couldn't be deleted.
Fix this and allow the user to manipulate the mdb with or without a
querier.
Signed-off-by: Satish Ashok <sashok@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 11 Jul 2015 01:16:37 +0000 (18:16 -0700)]
Merge branch 'netdev_unregister_races'
Julian Anastasov says:
====================
net: fixes for device unregistration
Test script from Eric W. Biederman can catch a problem
where packets from backlog are processed long after the last
synchronize_net call. This can be reproduced after few tests
if commit 381c759d9916 ("ipv4: Avoid crashing in ip_error")
is reverted for the test. Incoming packets do not hold
reference to device but even if they do, subsystems do not
expect packets to fly during and after the NETDEV_UNREGISTER
event.
The first fix has the cost of netif_running check in fast path.
The second fix calls rcu_read_lock while local IRQ is disabled,
I hope this is not against the rules.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Incoming packet should be either in backlog queue or
in RCU read-side section. Otherwise, the final sequence of
flush_backlog() and synchronize_net() may miss packets
that can run without device reference:
CPU 1 CPU 2
skb->dev: no reference
process_backlog:__skb_dequeue
process_backlog:local_irq_enable
on_each_cpu for
flush_backlog => IPI(hardirq): flush_backlog
- packet not found in backlog
CPU delayed ...
synchronize_net
- no ongoing RCU
read-side sections
netdev_run_todo,
rcu_barrier: no
ongoing callbacks
__netif_receive_skb_core:rcu_read_lock
- too late
free dev
process packet for freed dev
Fixes: 6e583ce5242f ("net: eliminate refcounting in backlog queue") Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
net: do not process device backlog during unregistration
commit 381c759d9916 ("ipv4: Avoid crashing in ip_error")
fixes a problem where processed packet comes from device
with destroyed inetdev (dev->ip_ptr). This is not expected
because inetdev_destroy is called in NETDEV_UNREGISTER
phase and packets should not be processed after
dev_close_many() and synchronize_net(). Above fix is still
required because inetdev_destroy can be called for other
reasons. But it shows the real problem: backlog can keep
packets for long time and they do not hold reference to
device. Such packets are then delivered to upper levels
at the same time when device is unregistered.
Calling flush_backlog after NETDEV_UNREGISTER_FINAL still
accounts all packets from backlog but before that some packets
continue to be delivered to upper levels long after the
synchronize_net call which is supposed to wait the last
ones. Also, as Eric pointed out, processed packets, mostly
from other devices, can continue to add new packets to backlog.
Fix the problem by moving flush_backlog early, after the
device driver is stopped and before the synchronize_net() call.
Then use netif_running check to make sure we do not add more
packets to backlog. We have to do it in enqueue_to_backlog
context when the local IRQ is disabled. As result, after the
flush_backlog and synchronize_net sequence all packets
should be accounted.
Thanks to Eric W. Biederman for the test script and his
valuable feedback!
Reported-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Fixes: 6e583ce5242f ("net: eliminate refcounting in backlog queue") Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'parisc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"We have one important patch from Dave Anglin and myself which fixes
PTE/TLB race conditions which caused random segmentation faults on our
debian buildd servers, and one patch from Alex Ivanov which speeds up
the graphical text console on the STI framebuffer driver"
* 'parisc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix some PTE/TLB race conditions and optimize __flush_tlb_range based on timing results
stifb: Implement hardware accelerated copyarea
Stephen Smalley [Fri, 10 Jul 2015 13:40:59 +0000 (09:40 -0400)]
selinux: fix mprotect PROT_EXEC regression caused by mm change
commit 66fc13039422ba7df2d01a8ee0873e4ef965b50b ("mm: shmem_zero_setup
skip security check and lockdep conflict with XFS") caused a regression
for SELinux by disabling any SELinux checking of mprotect PROT_EXEC on
shared anonymous mappings. However, even before that regression, the
checking on such mprotect PROT_EXEC calls was inconsistent with the
checking on a mmap PROT_EXEC call for a shared anonymous mapping. On a
mmap, the security hook is passed a NULL file and knows it is dealing
with an anonymous mapping and therefore applies an execmem check and no
file checks. On a mprotect, the security hook is passed a vma with a
non-NULL vm_file (as this was set from the internally-created shmem
file during mmap) and therefore applies the file-based execute check
and no execmem check. Since the aforementioned commit now marks the
shmem zero inode with the S_PRIVATE flag, the file checks are disabled
and we have no checking at all on mprotect PROT_EXEC. Add a test to
the mprotect hook logic for such private inodes, and apply an execmem
check in that case. This makes the mmap and mprotect checking
consistent for shared anonymous mappings, as well as for /dev/zero and
ashmem.
Cc: <stable@vger.kernel.org> # 4.1.x Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Paul Moore <pmoore@redhat.com>
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes and clean-up from Catalin Marinas:
- ACPI fix when checking the validity of the GICC MADT subtable
- handle debug exceptions in the el*_inv exception entries
- remove pointless register assignment in two compat syscall wrappers
- unnecessary include path
- defconfig update
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: entry32: remove pointless register assignment
arm64: entry: handle debug exceptions in el*_inv
arm64: Keep the ARM64 Kconfig selects sorted
ACPI / ARM64 : use the new BAD_MADT_GICC_ENTRY macro
ACPI / ARM64: add BAD_MADT_GICC_ENTRY() macro
arm64: defconfig: Add Ceva ahci to the defconfig
arm64: remove another unnecessary libfdt include path
parisc: Fix some PTE/TLB race conditions and optimize __flush_tlb_range based on timing results
The increased use of pdtlb/pitlb instructions seemed to increase the
frequency of random segmentation faults building packages. Further, we
had a number of cases where TLB inserts would repeatedly fail and all
forward progress would stop. The Haskell ghc package caused a lot of
trouble in this area. The final indication of a race in pte handling was
this syslog entry on sibaris (C8000):
Note that the pte value is 0 except for the accessed bit 0x100. This bit
shouldn't be set without the present bit.
It should be noted that the madvise system call is probably a trigger for many
of the random segmentation faults.
In looking at the kernel code, I found the following problems:
1) The pte_clear define didn't take TLB lock when clearing a pte.
2) We didn't test pte present bit inside lock in exception support.
3) The pte and tlb locks needed to merged in order to ensure consistency
between page table and TLB. This also has the effect of serializing TLB
broadcasts on SMP systems.
The attached change implements the above and a few other tweaks to try
to improve performance. Based on the timing code, TLB purges are very
slow (e.g., ~ 209 cycles per page on rp3440). Thus, I think it
beneficial to test the split_tlb variable to avoid duplicate purges.
Probably, all PA 2.0 machines have combined TLBs.
I dropped using __flush_tlb_range in flush_tlb_mm as I realized all
applications and most threads have a stack size that is too large to
make this useful. I added some comments to this effect.
Since implementing 1 through 3, I haven't had any random segmentation
faults on mx3210 (rp3440) in about one week of building code and running
as a Debian buildd.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Cc: stable@vger.kernel.org # v3.18+ Signed-off-by: Helge Deller <deller@gmx.de>
Alex Ivanov [Mon, 15 Jun 2015 05:50:45 +0000 (08:50 +0300)]
stifb: Implement hardware accelerated copyarea
This patch adds hardware assisted scrolling. The code is based upon the
following investigation: https://parisc.wiki.kernel.org/index.php/NGLE#Blitter
A simple 'time ls -la /usr/bin' test shows 1.6x speed increase over soft
copy and 2.3x increase over FBINFO_READS_FAST (prefer soft copy over
screen redraw) on Artist framebuffer.
Signed-off-by: Alex Ivanov <lausgans@gmail.com> Signed-off-by: Helge Deller <deller@gmx.de>
Merge tag 'powerpc-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- opal-prd mmap fix from Vaidy
- set kernel taint for MCEs from Daniel
- alignment exception description from Anton
- ppc4xx_hsta_msi build fix from Daniel
- opal-elog interrupt fix from Alistair
- core_idle_state race fix from Shreyas
- hv-24x7 lockdep fix from Sukadev
- multiple cxl fixes from Daniel, Ian, Mikey & Maninder
- update MAINTAINERS to point at shared tree
* tag 'powerpc-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
cxl: Check if afu is not null in cxl_slbia
powerpc: Update MAINTAINERS to point at shared tree
powerpc/perf/24x7: Fix lockdep warning
cxl: Fix off by one error allowing subsequent mmap page to be accessed
cxl: Fail mmap if requested mapping is larger than assigned problem state area
cxl: Fix refcounting in kernel API
powerpc/powernv: Fix race in updating core_idle_state
powerpc/powernv: Fix opal-elog interrupt handler
powerpc/ppc4xx_hsta_msi: Include ppc-pci.h to fix reference to hose_list
powerpc: Add plain English description for alignment exception oopses
cxl: Test the correct mmio space before unmapping
powerpc: Set the correct kernel taint on machine check errors
cxl/vphb.c: Use phb pointer after NULL check
powerpc/powernv: Fix vma page prot flags in opal-prd driver
This flag requires the driver to read back the command register after it
is written in the block I/O path. This ensures that the hardware has
fully processed the new command and moved the aperture appropriately.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Ross Zwisler [Fri, 10 Jul 2015 17:06:13 +0000 (11:06 -0600)]
nfit: update block I/O path to use PMEM API
Update the nfit block I/O path to use the new PMEM API and to adhere to
the read/write flows outlined in the "NVDIMM Block Window Driver
Writer's Guide":
For performance and media durability the mapping for a BLK aperture is
moved to a write-combining mapping which is consistent with
memcpy_to_pmem() and wmb_blk().
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Fri, 10 Jul 2015 18:07:03 +0000 (14:07 -0400)]
tools/testing/nvdimm: add mock acpi_nfit_flush_address entries to nfit_test
In preparation for fixing the BLK path to properly use "directed
pcommit" enable the unit test infrastructure to emit mock "flush"
tables. Writes to these flush addresses trigger a memory controller to
flush its internal buffers to persistent media, similar to the x86
"pcommit" instruction.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Fri, 10 Jul 2015 17:06:12 +0000 (11:06 -0600)]
tools/testing/nvdimm: fix return code for unimplemented commands
The implementation for the new "DIMM Flags" DSM relies on the -ENOTTY
return code to indicate that the flags are unimplimented and to fall
back to a safe default. As is the -ENXIO error code erroneoously
indicates to fail enabling a BLK region.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Fri, 10 Jul 2015 17:06:11 +0000 (11:06 -0600)]
tools/testing/nvdimm: mock ioremap_wt
In the 4.2-rc1 merge the default_memremap_pmem() implementation switched
from ioremap_nocache() to ioremap_wt(). Add it to the list of mocked
routines to restore the ability to run the unit tests.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Ross Zwisler [Fri, 10 Jul 2015 17:06:10 +0000 (11:06 -0600)]
pmem: add maintainer for include/linux/pmem.h
The file include/linux/pmem.h was recently created to hold the PMEM API,
and is logically part of the PMEM driver. Add an entry for this file to
MAINTAINERS.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We currently set x27 in compat_sys_sigreturn_wrapper and
compat_sys_rt_sigreturn_wrapper, similarly to what we do with r8/why on
32-bit ARM, in an attempt to prevent sigreturns from being restarted.
However, on arm64 we have always used pt_regs::syscallno for syscall
restarting (for both native and compat tasks), and x27 is never
inspected again before being overwritten in kernel_exit.
This patch removes the pointless register assignments.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
James Hogan [Fri, 17 Apr 2015 09:44:16 +0000 (10:44 +0100)]
MIPS: Pistachio: Support CDMM & Fast Debug Channel
Implement the mips_cdmm_phys_base() platform callback to provide a
default Common Device Memory Map (CDMM) physical base address for the
Pistachio SoC. This allows the CDMM in each VPE to be configured and
probed for devices, such as the Fast Debug Channel (FDC).
The physical address chosen is just below the default CPC address, which
appears to also be unallocated.
The FDC IRQ is also usable on Pistachio, and is routed through the GIC,
so implement the get_c0_fdc_int() platform callback using
gic_get_c0_fdc_int(), so the FDC driver doesn't have to fall back to
polling.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Andrew Bresticker <abrestic@chromium.org> Cc: James Hartley <james.hartley@imgtec.com> Cc: linux-mips@linux-mips.org Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Patchwork: http://patchwork.linux-mips.org/patch/9749/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Fri, 17 Apr 2015 09:44:15 +0000 (10:44 +0100)]
MIPS: Malta: Make GIC FDC IRQ workaround Malta specific
Wider testing reveals that the Fast Debug Channel (FDC) interrupt is
routed through the GIC just fine on Pistachio SoC, even though it
contains interAptiv cores. Clearly the FDC interrupt routing problems
previously observed on interAptiv and proAptiv cores are specific to the
Malta FPGA bitstreams.
Move the workaround for interAptiv and proAptiv out of
gic_get_c0_fdc_int() in the GIC irqchip driver into Malta's
get_c0_fdc_int() platform callback, to allow the Pistachio SoC to use
the FDC interrupt.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Andrew Bresticker <abrestic@chromium.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: linux-mips@linux-mips.org Reviewed-by: Andrew Bresticker <abrestic@chromium.org> Cc: James Hartley <james.hartley@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/9748/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MT_SMP is not the only SMP option for MT cores. The MT_SMP option
allows more than one VPE per core to appear as a secondary CPU in the
system. Because of how CM works, it propagates the address-based
cache ops to the secondary cores but not the index-based ones.
Because of that, the code does not use IPIs to flush the L1 caches on
secondary cores because the CM would have done that already. However,
the CM functionality is independent of the type of SMP kernel so even in
non-MT kernels, IPIs are not necessary. As a result of which, we change
the conditional to depend on the CM presence. Moreover, since VPEs on
the same core share the same L1 caches, there is no need to send an
IPI on all of them so we calculate a suitable cpumask with only one
VPE per core.
Dave Airlie [Fri, 10 Jul 2015 05:58:43 +0000 (15:58 +1000)]
Merge tag 'drm-intel-fixes-2015-07-09' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Pile of fixes for either 4.2 issues or cc: stable. This should fix the 2nd
kind of WARNING Linus's been seeing, please ask him to scream if that's
not the case.
* tag 'drm-intel-fixes-2015-07-09' of git://anongit.freedesktop.org/drm-intel:
Revert "drm/i915: Allocate context objects from stolen"
drm/i915: Declare the swizzling unknown for L-shaped configurations
drm/i915: Use crtc_state->active in primary check_plane func
drm/i915: Check crtc->active in intel_crtc_disable_planes
drm/i915: Restore all GGTT VMAs on resume
drm/i915/chv: fix HW readout of the port PLL fractional divider
Dave Airlie [Fri, 10 Jul 2015 05:55:48 +0000 (15:55 +1000)]
Merge branch 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
radeon and amdgpu fixes for 4.2. All over the place:
- fix cursor corruption on resume and re-enable no VT switch on suspend
- vblank fixes
- fix gpuvm error messages
- misc other fixes
* 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: disable vce init on cayman (v2)
drm/amdgpu: fix timeout calculation
drm/radeon: check if BO_VA is set before adding it to the invalidation list
drm/radeon: allways add the VM clear duplicate
Revert "Revert "drm/radeon: dont switch vt on suspend""
drm/radeon: Fold radeon_set_cursor() into radeon_show_cursor()
drm/radeon: unpin cursor BOs on suspend and pin them again on resume (v2)
drm/radeon: Clean up reference counting and pinning of the cursor BOs
drm/radeon: fix underflow in r600_cp_dispatch_texture()
drm/radeon: default to 2048 MB GART size on SI+
drm/radeon: fix HDP flushing
drm/radeon: use RCU query for GEM_BUSY syscall
drm/amdgpu: Handle irqs only based on irq ring, not irq status regs.
drm/radeon: Handle irqs only based on irq ring, not irq status regs.
Eric Dumazet [Thu, 9 Jul 2015 16:56:07 +0000 (18:56 +0200)]
bridge: fix potential crash in __netdev_pick_tx()
Commit c29390c6dfee ("xps: must clear sender_cpu before forwarding")
fixed an issue in normal forward path, caused by sender_cpu & napi_id
skb fields being an union.
Bridge is another point where skb can be forwarded, so we need
the same cure.
Bug triggers if packet was received on a NIC using skb_mark_napi_id()
Fixes: 2bd82484bb4c ("xps: fix xps for stacked devices") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Bob Liu <bob.liu@oracle.com> Tested-by: Bob Liu <bob.liu@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: axienet: Fix devm_ioremap_resource return value check
Value returned by devm_ioremap_resource() was checked for non-NULL but
devm_ioremap_resource() returns IOMEM_ERR_PTR, not NULL. In case of
error this could lead to dereference of ERR_PTR.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com> Cc: <stable@vger.kernel.org> Fixes: 46aa27df8853 ("net: axienet: Use devm_* calls") Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Axtens [Thu, 9 Jul 2015 23:04:25 +0000 (09:04 +1000)]
cxl: Check if afu is not null in cxl_slbia
The pointer to an AFU in the adapter's list of AFUs can be null
if we're in the process of removing AFUs. The afu_list_lock
doesn't guard against this.
Say we have 2 slices, and we're in the process of removing cxl.
- We remove the AFUs in order (see cxl_remove). In cxl_remove_afu
for AFU 0, we take the lock, set adapter->afu[0] = NULL, and
release the lock.
- Then we get an slbia. In cxl_slbia we take the lock, and set
afu = adapter->afu[0], which is NULL.
- Therefore our attempt to check afu->enabled will blow up.
Therefore, check if afu is a null pointer before dereferencing it.
Cc: stable@vger.kernel.org Signed-off-by: Daniel Axtens <dja@axtens.net> Acked-by: Michael Neuling <mikey@neuling.org> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Kevin Hilman [Thu, 9 Jul 2015 22:38:16 +0000 (15:38 -0700)]
Merge tag 'omap-for-v4.2/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.2-rc1" from Tony Lindgren:
Minor fixes for omaps against v4.2-rc1. Mostly just minor dts changes
except for a GPMC fix to not use names for probing devices. Also a
one liner clean-up to remove unecessary return from a void function.
The summary for the changes being:
- Fix probe for GPMC devices by reoving limitations based on device
name
- Remove unnecessary return from a void function
- Revert beaglebone RTC sleep fix, we now have a better fix merged
- Add am4372 EMIF node to fix a warning
- Add am57xx-beagle-x15 power supply to fix USB2 if USB1 is disabled
- Disable rfbi for am4372 as it does not have a driver
* tag 'omap-for-v4.2/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372.dtsi: disable rfbi
ARM: dts: am57xx-beagle-x15: Provide supply for usb2_phy2
ARM: dts: am4372: Add emif node
Revert "ARM: dts: am335x-boneblack: disable RTC-only sleep"
ARM: OMAP2+: Remove unnessary return statement from the void function, omap2_show_dma_caps
memory: omap-gpmc: Fix parsing of devices
Kevin Hilman [Thu, 9 Jul 2015 22:08:44 +0000 (15:08 -0700)]
Merge tag 'sunxi-late-for-4.2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner late changes for 4.2" from Maxime Ripard:
Allwinner late changes for 4.2
A bunch of defconfig changes, and some patches to make the Allwinner H3 and
A33 boot properly.
* tag 'sunxi-late-for-4.2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: Enable simplefb in the defconfig
ARM: Remove deprecated symbol from defconfig files
ARM: sunxi: Add Machine support for A33
ARM: sunxi: Introduce Allwinner H3 support
Documentation: sunxi: Update Allwinner SoC documentation
David S. Miller [Thu, 9 Jul 2015 22:05:33 +0000 (15:05 -0700)]
Merge branch 'pktgen-races'
Oleg Nesterov says:
====================
net: pktgen: fix race between pktgen_thread_worker() and kthread_stop()
I am not familiar with this code and I have no idea how to test
these changes, so 2/2 comes as a separate change. 1/2 looks like
the obvious bugfix, and probably candidate for -stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: pktgen: kill the "Wait for kthread_stop" code in pktgen_thread_worker()
pktgen_thread_worker() doesn't need to wait for kthread_stop(), it
can simply exit. Just pktgen_create_thread() and pg_net_exit() should
do get_task_struct()/put_task_struct(). kthread_stop(dead_thread) is
fine.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: pktgen: fix race between pktgen_thread_worker() and kthread_stop()
pktgen_thread_worker() is obviously racy, kthread_stop() can come
between the kthread_should_stop() check and set_current_state().
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Reported-by: Jan Stancek <jstancek@redhat.com> Reported-by: Marcelo Leitner <mleitner@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cdc_ncm: Add support for moving NDP to end of NCM frame
NCM specs are not actually mandating a specific position in the frame for
the NDP (Network Datagram Pointer). However, some Huawei devices will
ignore our aggregates if it is not placed after the datagrams it points
to. Add support for doing just this, in a per-device configurable way.
While at it, update NCM subdrivers, disabling this functionality in all of
them, except in huawei_cdc_ncm where it is enabled instead.
We aren't making any distinction between different Huawei NCM devices,
based on what the vendor driver does. Standard NCM devices are left
unaffected: if they are compliant, they should be always usable, still
stay on the safe side.
This change has been tested and working with a Huawei E3131 device (which
works regardless of NDP position), a Huawei E3531 (also working both
ways) and an E3372 (which mandates NDP to be after indexed datagrams).
V1->V2:
- corrected wrong NDP acronym definition
- fixed possible NULL pointer dereference
- patch cleanup
V2->V3:
- Properly account for the NDP size when writing new packets to SKB
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Wed, 8 Jul 2015 09:05:22 +0000 (14:35 +0530)]
drivers: net: cpsw: fix disabling of tx interrupt in rx isr
In commit 'c03abd84634d ("net: ethernet: cpsw: don't requests
IRQs we don't use")', common isr is split into tx and rx, but
in rx isr tx interrupt is also disabledi in cpsw_disable_irq().
So tx interrupts are not handled during rx interrupts and rx
napi completion and results in poor tx performance by 40Mbps.
Fixing by disabling only rx interrupt in rx isr.
Cc: Felipe Balbi <balbi@ti.com> Cc: <stable@vger.kernel.org> # v4.0+ Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'hpfs-patches' (patches from Mikulas Patocka)
Merge hpfs updates from Mikulas Patocka.
Mainly fstrim support, with some minor other cleanups.
These were actually sent during the merge window, but I wanted to wait
for the FSTRIM compat handling cleanup before applying them. Mikulas
sent that earlier today.
* emailed patches from Mikulas Patocka <mikulas@twibright.com>:
hpfs: hpfs_error: Remove static buffer, use vsprintf extension %pV instead
hpfs: kstrdup() out of memory handling
hpfs: Remove unessary cast
hpfs: add fstrim support
i2c: Mark instantiated device nodes with OF_POPULATE
Mark (and unmark) device nodes with the POPULATE flag as appropriate.
This is required to avoid multi probing when using I2C and device
overlays containing a mux.
This patch is also more careful with the release of the adapter device
which caused a deadlock with muxes, and does not break the build
on !OF since the node flag accessors are not defined then.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Axel Lin [Tue, 30 Jun 2015 03:41:58 +0000 (11:41 +0800)]
i2c: jz4780: Fix return value if probe fails
Current code returns 0 if fails to read clock-frequency DT property,
fix it. Also add checking return value of clk_prepare_enable and
propagate return value of devm_request_irq.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"There is a fix for CephFS and RBD when used within containers/namespaces,
and a fix for the address learning the client is supposed to do when
initially talking to the Ceph cluster.
There are also two patches updating MAINTAINERS. One breaks out the
common Ceph code shared by fs/ceph and drivers/block/rbd.c into a
separate entry with the appropriate maintainers listed. The second
adds a second reference to the github tree where the Ceph client
development takes place (before it is pushed to korg and then to you).
The goal here is to move closer to a situation where Ilya Dryomov or
one of the other maintainers can push things to you if I am
unavailable. Ilya has done most of the work preparing branches for
upstream recently; you should not be surprised to hear from him if I
am trapped in some internet-less wasteland or hit by a bus or
something. In the meantime, we'll work on getting him added to the
kernel web of trust"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
MAINTAINERS: add secondary tree for ceph modules
MAINTAINERS: update ceph entries
libceph: treat sockaddr_storage with uninitialized family as blank
libceph: enable ceph in a non-default network namespace
The FITRIM ioctl has the same arguments on 32-bit and 64-bit
architectures, so we can add it to the list of compatible ioctls and
drop it from compat_ioctl method of various filesystems.
Paul Moore [Thu, 9 Jul 2015 18:20:36 +0000 (14:20 -0400)]
selinux: don't waste ebitmap space when importing NetLabel categories
At present we don't create efficient ebitmaps when importing NetLabel
category bitmaps. This can present a problem when comparing ebitmaps
since ebitmap_cmp() is very strict about these things and considers
these wasteful ebitmaps not equal when compared to their more
efficient counterparts, even if their values are the same. This isn't
likely to cause problems on 64-bit systems due to a bit of luck on
how NetLabel/CIPSO works and the default ebitmap size, but it can be
a problem on 32-bit systems.
This patch fixes this problem by being a bit more intelligent when
importing NetLabel category bitmaps by skipping over empty sections
which should result in a nice, efficient ebitmap.
Cc: stable@vger.kernel.org # 3.17 Signed-off-by: Paul Moore <pmoore@redhat.com>
The firmware class uevent function accessed the "fw_priv->buf" buffer
without the proper locking and testing for NULL. This is an old bug
(looks like it goes back to 2012 and commit 1244691c73b2: "firmware
loader: introduce firmware_buf"), but for some reason it's triggering
only now in 4.2-rc1.
Shuah Khan is trying to bisect what it is that causes this to trigger
more easily, but in the meantime let's just fix the bug since others are
hitting it too (at least Ingo reports having seen it as well).
Reported-and-tested-by: Shuah Khan <shuahkh@osg.samsung.com> Acked-by: Ming Lei <ming.lei@canonical.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: avoid setting up anonymous pages into file mapping
Reading page fault handler code I've noticed that under right
circumstances kernel would map anonymous pages into file mappings: if
the VMA doesn't have vm_ops->fault() and the VMA wasn't fully populated
on ->mmap(), kernel would handle page fault to not populated pte with
do_anonymous_page().
Let's change page fault handler to use do_anonymous_page() only on
anonymous VMA (->vm_ops == NULL) and make sure that the VMA is not
shared.
For file mappings without vm_ops->fault() or shred VMA without vm_ops,
page fault on pte_none() entry would lead to SIGBUS.
Sage Weil [Thu, 9 Jul 2015 15:47:37 +0000 (11:47 -0400)]
MAINTAINERS: add secondary tree for ceph modules
The Ceph kernel code is primarily developed in the github tree, and only
pushed to the korg tree before going to Linus. If Sage is unavailable and
another maintainer needs to push something upstream, pull requests may
originate from the github tree instead of Sage's korg tree.
Signed-off-by: Sage Weil <sage@redhat.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
libceph: treat sockaddr_storage with uninitialized family as blank
addr_is_blank() should return true if family is neither AF_INET nor
AF_INET6. This is what its counterpart entity_addr_t::is_blank_ip() is
doing and it is the right thing to do: in process_banner() we check if
our address is blank and if it is "learn" it from our peer. As it is,
we never learn our address and always send out a blank one. This goes
way back to ceph.git commit dd732cbfc1c9 ("use sockaddr_storage; and
some ipv6 support groundwork") from 2009.
While at at, do not open-code ipv6_addr_any() and use INADDR_ANY
constant instead of 0.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Sage Weil <sage@redhat.com>
Ilya Dryomov [Thu, 25 Jun 2015 14:47:45 +0000 (17:47 +0300)]
libceph: enable ceph in a non-default network namespace
Grab a reference on a network namespace of the 'rbd map' (in case of
rbd) or 'mount' (in case of ceph) process and use that to open sockets
instead of always using init_net and bailing if network namespace is
anything but init_net. Be careful to not share struct ceph_client
instances between different namespaces and don't add any code in the
!CONFIG_NET_NS case.
This is based on a patch from Hong Zhiguo <zhiguohong@tencent.com>.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Sage Weil <sage@redhat.com>
projects / karo-tx-linux.git / log