Martin Bugge [Thu, 5 Dec 2013 12:02:20 +0000 (09:02 -0300)]
[media] adv7511: disable register reset by HPD
Whenever the hotplug pin is pulled low the chip resets a whole bunch
of registers. It turns out that this can be turned off on the adv7511.
Do so, as this 'feature' introduces race conditions in setting up
registers, particular when the hotplug pin bounces a lot.
Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
[media] em28xx: prevent registering wrong interfaces for audio-only
A few devices (em2860) use a separate interface for audio only
Audio Vendor Class USB. That interface should not be used by
Remote Controller, Analog TV or Digital TV.
Prevents initializing all non-audio extensions for the audio
only interface.
[media] em28xx: move analog-specific init to em28xx-video
There are several init code inside em28xx-cards that are actually
part of analog initialization. Move the code to em28x-video, in
order to remove part of the mess.
In thesis, no functional changes so far.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using two I2C operations between write and read,
use just one i2c_transfer. That allows I2C mutexes to not
let any other I2C transfer between the two.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com> Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dan Carpenter [Wed, 18 Dec 2013 07:29:24 +0000 (04:29 -0300)]
[media] v4l: omap4iss: Restore irq flags correctly in omap4iss_video_buffer_next()
The spin_lock_irqsave() macro is not nestable. The second call will
overwrite the first record of "flags" so the IRQs will not be enabled
correctly at the end of the function.
In the current code, this function is always called from the IRQ handler
so everything works fine and this fix doesn't change anything.
Dan Carpenter [Mon, 16 Dec 2013 20:19:50 +0000 (17:19 -0300)]
[media] v4l: omap4iss: use snprintf() to make smatch happy
Smatch complains here because name is a 32 character buffer and we
adding the "OMAP4 ISS " prefix as well for a total of 42 characters.
The sd->name buffer can only hold 32 characters. I've changed it to use
snprintf() to silence the overflow warning.
Also I have removed the call to strlcpy() which is a no-op.
[media] exynos4-is: Remove dependency on PM_RUNTIME from Kconfig
Now when the sub-drivers are fixed to work with runtime PM disabled
this erroneous dependency can be removed.
The CAM and ISP power domains should be left in active state by the
platform if runtime PM is not used.
[media] exynos4-is: Correct clean up sequence on error path in fimc_is_probe()
The memory allocator is being initialized before registering the subdevs
so reverse the cleanup sequence to avoid trying unregister not registered
subdevs.
[media] exynos4-is: Activate mipi-csis in probe() if runtime PM is disabled
Devices should also operate normally when runtime PM is not enabled.
In case runtime PM is disabled activate the device already in probe().
Any related power domain needs to be then left permanently in active
state by the platform.
Andrzej Hajda [Thu, 5 Dec 2013 11:38:39 +0000 (08:38 -0300)]
[media] Add driver for Samsung S5K5BAF camera sensor
Driver for Samsung S5K5BAF UXGA 1/5" 2M CMOS Image Sensor with
embedded SoC ISP. The device is exposed as two V4L2 subdevices:
- S5K5BAF-CIS - the image sensor matrix, fixed 1600x1200 format,
no controls.
- S5K5BAF-ISP - the Image Signal Processor, formats up to 1600x1200,
pre/post ISP cropping, downscaling via selection API, controls.
[m.chehab@samsung.com: Whitespace cleanups] Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
[media] subdev autoselect only works if I2C and I2C_MUX is selected
As reported by the kbuild test robot <fengguang.wu@intel.com>:
> warning: (VIDEO_EM28XX_DVB) selects DVB_M88DS3103 which has unmet direct dependencies (MEDIA_SUPPORT && DVB_CORE && I2C && I2C_MUX)
> drivers/built-in.o: In function `m88ds3103_release':
> >> m88ds3103.c:(.text+0x1ab1af): undefined reference to `i2c_del_mux_adapter'
> drivers/built-in.o: In function `m88ds3103_attach':
> >> (.text+0x1ab342): undefined reference to `i2c_add_mux_adapter'
There are 3 possible ways to fix it:
1) make em28xx dependent on I2C_MUX.
That sounds wrong, as the em28xx bridge doesn't have i2c muxes on it,
and just one frontend has.
Well, subdevs could eventually be converted to, instead of using dvb
i2c gate control, to use i2c mux support.
That makes sense, but it takes time and lots of effort. Not sure if
this will happen anytime soon.
2) MEDIA_SUBDRV_AUTOSELECT can be dependent of I2C and I2C_MUX.
That means that users will need to manually enable I2C_MUX on some
distributions. Not sure about others, but, on Fedora, this option is
disabled.
So, it can end by generating a number of complains from users
that their devices suddenly stopped working after a Kernel upgrade,
at least until all distros that ship Kernels with I2C_MUX enabled.
3) if MEDIA_SUBDRV_AUTOSELECT is selected, it will select I2C and I2C_MUX.
Of course, MEDIA_SUBDRV_AUTOSELECT will need to inherit all dependencies
that I2C and I2C_MUX have (only HAS_IOMEM).
The disadvantage is that, if new dependencies are added on I2C, they'll
also need to be added here.
As the hole idea of autoselect is to let the user not bother about whatever
frontend/tuner is used by a driver, IMHO, (3) is the better solution.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Thu, 12 Dec 2013 12:04:44 +0000 (09:04 -0300)]
[media] omap24xx/tcm825x: move to staging for future removal
The omap24xx driver and the tcm825x sensor driver are the only two
remaining drivers to still use the old deprecated v4l2-int-device API.
Nobody maintains these drivers anymore. But unfortunately the v4l2-int-device
API is used by out-of-tree drivers (MXC platform). This is a very bad situation
since as long as this deprecated API stays in the kernel there is no reason for
those out-of-tree drivers to convert.
This patch moves v4l2-int-device and the two drivers that depend on it to
staging in preparation for their removal.
If someone would be interested in getting these drivers to work, then start with
this since it's not very far from the state where they used to work:
Hans Verkuil [Thu, 12 Dec 2013 10:35:22 +0000 (07:35 -0300)]
[media] sn9c102: prepare for removal by moving it to staging
During the last media summit meeting it was decided to move this driver to
staging as the first step to removing it altogether.
Most webcams covered by this driver are now supported by gspca. Nobody has the
hardware to convert the remaining devices to gspca.
This driver needs a major overhaul to have it conform to the latest frameworks
and compliancy tests.
Without hardware, however, this is next to impossible. Given the fact that
this driver seems to be pretty much unused (it has been removed from Fedora
several versions ago and nobody complained about that), we decided to drop
this driver.
This patch moves it to staging. Some time in 2014 we will drop it completely.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Luca Risolia <luca.risolia@studio.unibo.it> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari [Mon, 2 Dec 2013 16:11:21 +0000 (13:11 -0300)]
[media] m88ds3103: remove unneeded AGC from inittab
Optimal AGC is highly depended on used RF tuner and due to that
it is already included to chip configuration. However, inittab
has default AGC value, which was later replaced by one from config.
Add also comment to all chip configuration options about default
values and if those are needed to set or not.
Reported-by: David Howells <dhowells@redhat.com> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Used synthesizer is very typical integer-N PLL, with configurable
reference frequency divider, output frequency divider and of
course N itself. Most common method to calculate values is first
select output divider, then calculate VCO frequency and finally
calculate PLL N from VCO frequency. Do it that way.
Also make some cleanups for filter logic and signal strength.
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari [Tue, 19 Nov 2013 23:32:42 +0000 (20:32 -0300)]
[media] m88ds3103: use I2C mux for tuner I2C adapter
Switch standard I2C adapter to muxed I2C adapter.
David reported that I2C adapter implementation caused deadlock.
I discussed with Jean and he suggested to implement it as a
multiplexed i2c adapter because tuner I2C bus could be seen like
own I2C segment.
Reported-by: David Howells <dhowells@redhat.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On dib8000, the block error count is a monotonic 32 bits register.
With DVBv5 stats, we use a 64 bits counter, that it is reset
when a new channel is tuned.
Change the UCB counting start from 0 and to be returned with
64 bits, just like the API requests.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com> Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Better to have Signal strength in dB.
This takes a very rough estimation for the signal strength,
that was calibrated using a Dektec DTA-2111 Gold RF generator
and a Pixelview dib8076 stick.
It estimates the signal strength using a linear equation where:
- the max is -22.5 dBm, with returns 55953
- the min is -35.0 dBm, with returns 50110
With -22dBm, the signal strengh is returned as 65535.
Unfortunately, the min strength generated with DTA-2111 is
-35dBm.
It should be noticed that approximating it by a linear equation
is not right. I should probably be splitting it into 0.5 dB
linear segments, in order to get a higher precision, just like
it is done on mb86a20s, but that would force me to add some
attenuators, in order to get dB levels below -35dBm, which is,
btw, strong enough to get signal lock.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com> Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
On ISDB-T, the valid values for interleaving are 0, 1, 2 and 4.
While the first 3 are properly reported, the last one is reported
as 3 instead. Fix it.
Tested with a Dektec DTA-2111 RF generator.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com> Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
[media] dib8000: improves the auto search mode check logic
The logic that detects if auto search mode should be used is too
complex.
Also, it doesn't cover all cases, as the dib8000_tune logic
requires either auto mode or a fully specified manual mode.
So, move it to a separate function and add some extra debug
data to help identifying when it falled back to auto mode,
because the manual settings are invalid.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com> Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
[media] dib8000: Don't let tuner hang due to a call to get_frontend()
Both dvbv5-scan and dvbv5-zap tools call FE_GET_PROPERTY inside the
loop that checks for stats. If the frontend doesn't support DVBv5, it
falls back to call the DVBv5 stats APIs(FE_READ_BER, FE_READ_SIGNAL,
FE_READ_SNR and FE_READ_UNCORRECTED_BLOCKS).
A call to FE_GET_PROPERTY makes dvb-frontend core to call get_frontend().
However, due to a race condition on dib8000 between dib8000_get_frontend
and dib8000_tune, if get_frontend occurs too early, it causes the
tune state machine to fail and not get any lock.
This patch adds a workaround code that makes get_frontend() to just
return if none of the frontends have a SYNC. This change fixed the issue
with dvbv5-scan/dvbv5-zap, but a fine-tuned logic might be needed in
the future, when we implement DVBv5 stats on this frontend.
The procedure to test the bug and the fix is the one below:
As the dvb-frontend kthread can be called anytime, it can race
with some get status ioctl. So, it seems better to avoid one to
race with the other while reading a 32 bits register.
I can't see any other reason for having a mutex there at I2C, except
to provide such kind of protection, as the I2C core already has a
mutex to protect I2C transfers.
Note: instead of this approach, it could eventually remove the dib8000
specific mutex for it, and either group the 4 ops into one xfer or
to manually control the I2C mutex. The main advantage of the current
approach is that the changes are smaller and more puntual.
Jacek Anaszewski [Wed, 18 Dec 2013 14:14:00 +0000 (11:14 -0300)]
[media] s5p-jpeg: Adjust g_volatile_ctrl callback to Exynos4x12 needs
Whereas S5PC210 device produces decoded JPEG subsampling values that
map on V4L2_JPEG_CHROMA_SUBSAMPLNG values, the Exynos4x12 device
doesn't. This patch adds helper function s5p_jpeg_to_user_subsampling,
which performs suitable translation.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Jacek Anaszewski [Thu, 21 Nov 2013 16:34:01 +0000 (13:34 -0300)]
[media] s5p-jpeg: Ensure setting correct value of the chroma subsampling control
Exynos4x12 has limitations regarding setting chroma subsampling
of an output JPEG image. It cannot be lower than the subsampling
of the raw source image. Also in case of V4L2_JPEG_CHROMA_SUBSAMPLING_GRAY
option the source image fourcc has to be V4L2_PIX_FMT_GREY.
This patch implements try_ctrl callback containing mechanism that
prevents setting invalid value of the V4L2_CID_JPEG_CHROMA_SUBSAMPLING
control.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Jacek Anaszewski [Thu, 21 Nov 2013 16:33:52 +0000 (13:33 -0300)]
[media] s5p-jpeg: Synchronize V4L2_CID_JPEG_CHROMA_SUBSAMPLING control value
When output queue fourcc is set to any flavour of YUV,
the V4L2_CID_JPEG_CHROMA_SUBSAMPLING control value as
well as its in-driver cached counterpart have to be
updated with the subsampling property of the format
so as to be able to provide correct information to the
user space and preclude setting an illegal subsampling
mode for Exynos4x12 encoder.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Jacek Anaszewski [Fri, 22 Nov 2013 09:13:34 +0000 (06:13 -0300)]
[media] s5p-jpeg: Ensure correct capture format for Exynos4x12
Adjust capture format to the Exynos4x12 device limitations,
according to the subsampling value parsed from the source
JPEG image header. If the capture format was set to YUV with
subsampling lower than the one of the source JPEG image
the decoding process would not succeed.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Jacek Anaszewski [Thu, 21 Nov 2013 16:33:09 +0000 (13:33 -0300)]
[media] s5p-jpeg: Retrieve "YCbCr subsampling" field from the jpeg header
Make s5p_jpeg_parse_hdr function capable of parsing
"YCbCr subsampling" field of a jpeg file header. Store the
parsed value in the context.
The information about source JPEG subsampling is required to
make validation of destination format possible, which must be
conducted for exynos4x12 device as the decoding process will
not succeed if the destination format is set to YUV with
subsampling lower than the one of the source JPEG image.
With this knowledge the driver can adjust the destination format
appropriately.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Laurent Pinchart [Wed, 11 Dec 2013 12:33:03 +0000 (09:33 -0300)]
[media] v4l: sh_vou: Fix warnings due to improper casts and printk formats
Use the %zu and %pad printk specifiers to print size_t and dma_addr_t
variables. This fixes warnings on platforms where dma_addr_t has a
different size than int.
Josh Wu [Tue, 10 Dec 2013 12:25:47 +0000 (09:25 -0300)]
[media] v4l: atmel-isi: Should clear bits before set the hardware register
In the ISI driver it reads the config register to get original value,
then set the correct FRATE_DIV and YCC_SWAP_MODE directly. This will
cause some bits overlap.
So we need to clear these bits first, then set correct value. This patch
fix it.
Laurent Pinchart [Sat, 23 Nov 2013 02:06:54 +0000 (23:06 -0300)]
[media] v4l: atmel-isi: Make the MCK clock optional
ISI_MCK is the sensor master clock. It should be handled by the sensor
driver directly, as the ISI has no use for that clock. Make the clock
optional here while platforms transition to the correct model.
Laurent Pinchart [Mon, 25 Nov 2013 15:21:33 +0000 (12:21 -0300)]
[media] v4l: atmel-isi: Defer clock (un)preparation to enable/disable time
The PCLK and MCK clocks are prepared and unprepared at probe and remove
time. Clock (un)preparation isn't needed before enabling/disabling the
clocks, and the enable/disable operation happen in non-atomic context.
We can thus defer (un)preparation to enable/disable time.
Josh Wu [Thu, 24 Oct 2013 07:27:11 +0000 (04:27 -0300)]
[media] v4l: atmel-isi: remove SOF wait in start_streaming()
when a userspace applications calls the VIDIOC_STREAMON ioctl. The
V4L2 core calls the soc_camera_streamon function, which is responsible
for starting the video stream. It does so by first starting the atmel-isi
host by a call to the vb2_streamon function, and then starting the sensor
by a call to the video.s_stream sensor subdev operation.
That means we wait for a SOF in start_streaming() before call sensor's
s_stream(). It is possible no VSYNC interrupt arrive as the sensor
hasn't been started yet.
To avoid such case, this patch remove the code to wait for the VSYNC
interrupt. And such code is not necessary.
si4713_set_rds_radio_text will overwrite the terminating zero at the
end of the rds radio text string in order to send out a carriage return
as per the RDS spec.
Use a separate char buffer for the CR instead of corrupting the control
string.
Dinesh Ram [Tue, 15 Oct 2013 15:24:44 +0000 (12:24 -0300)]
[media] si4713: move supply list to si4713_platform_data
The supply list is needed by the platform driver, but not by the usb driver.
So this information belongs to the platform data and should not be hardcoded
in the subdevice driver.
projects / linux-beck.git / log