Saeed Mahameed [Tue, 1 Dec 2015 16:03:10 +0000 (18:03 +0200)]
net/mlx5: Add HW capabilities and structs for SR-IOV E-Switch
Update HCA capabilities and HW struct to include needed
capabilities for upcoming Ethernet Switch (SR-IOV E-Switch).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Tue, 1 Dec 2015 16:03:09 +0000 (18:03 +0200)]
net/mlx5_core: Add base sriov support
This patch adds SRIOV base support for mlx5 supported devices. The same
driver is used for both PFs and VFs; VFs are identified by the driver
through the flag MLX5_PCI_DEV_IS_VF added to the pci table entries.
Virtual functions are created as usual through writing a value to the
sriov_numvs sysfs file of the PF device. Upon instantiating VFs, they will
all be probed by the driver on the hypervisor. One can gracefully unbind
them through /sys/bus/pci/drivers/mlx5_core/unbind.
mlx5_wait_for_vf_pages() was added to ensure that when a VF dies without
executing proper teardown, the hypervisor driver waits till all of the
pages that were allocated at the hypervisor to maintain its operation
are returned.
In order for the VF to be operational, the PF needs to call enable_hca
for it. This can be done before the VFs are created through a call to
pci_enable_sriov.
If the there are VFs assigned to a VMs when the driver of the PF is
unloaded, all the VF will experience system error and PF driver unloads
cleanly; in this case pci_disable_sriov is not called and the devices
will show when running lspci. Once the PF driver is reloaded, it will
sync its data structures which maintain state on its VFs.
Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Modify these functions to have func_id argument to state which device we
are referring to. This is done as a preparation for SRIOV support where
a PF driver needs to control its virtual functions.
Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Mon, 30 Nov 2015 22:33:36 +0000 (17:33 -0500)]
alx: remove pointless assignment
Reasonably sure this doesn't serve any purpose.
CC: Jay Cliburn <jcliburn@gmail.com> CC: Chris Snook <chris.snook@gmail.com> CC: netdev@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset introduces needed infrastructure for link aggregation
offload - for both team and bonding. It also implements the offload
in mlxsw driver.
Particulary, this patchset introduces possibility for upper driver
(bond/team/bridge/..) to pass type-specific info down to notifier listeners.
Info is passed along with NETDEV_CHANGEUPPER/NETDEV_PRECHANGEUPPER
notifiers. Listeners (drivers of netdevs being enslaved) can react
accordingly.
Other extension is for run-time use. This patchset introduces
new netdev notifier type - NETDEV_CHANGELOWERSTATE. Along with this
notification, the upper driver (bond/team/bridge/..) can pass some
information about lower device change, particulary link-up and
TX-enabled states. Listeners (drivers of netdevs being enslaved)
can react accordingly.
The last part of the patchset is implementation of LAG offload in mlxsw,
using both previously introduced infrastructre extensions.
Note that bond-speficic (and ugly) NETDEV_BONDING_INFO used by mlx4
can be removed and mlx4 can use the extensions this patchset adds.
I plan to convert it and get rid of NETDEV_BONDING_INFO in
a follow-up patchset.
v2->v3:
- one small fix in patch 1
v1->v2:
- added patch 1 and 2 per Andy's request
- couple of more or less cosmetic changes described in couple other patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Dec 2015 11:12:29 +0000 (12:12 +0100)]
mlxsw: spectrum: Implement FDB add/remove/dump for LAG
Implement FDB offloading for lagged ports, including learning LAG FDB
entries, adding/removing static FDB entries and dumping existing LAG FDB
entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Dec 2015 11:12:23 +0000 (12:12 +0100)]
mlxsw: core: Add support for packets received from LAG port
Lower layer (pci) has information if the packet is received via LAG port.
If that is the case, it fills up rx_info accordingly. However upper
layer does not care about lag_id/port_index for received packets so
convert it to local_port before passing it up. For that conversion, lag
mapping array is introduced. Upper layer is responsible for setting up
the mapping according to what is set in HW.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Dec 2015 11:12:21 +0000 (12:12 +0100)]
bonding: set inactive flags on release
Be correct and symmetric to enslave and set inactive flags during release.
That gives LAG offload drivers - lower state change listeners - possibility
to do proper cleanup.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Dec 2015 11:12:19 +0000 (12:12 +0100)]
bonding: allow notifications for bond_set_slave_link_state
Similar to state notifications.
We allow caller to indicate if the notification should happen now or later,
depending on if he holds rtnl mutex or not. Introduce bond_slave_link_notify
function (similar to bond_slave_state_notify) which is later on called
with rtnl mutex and goes over slaves and executes delayed notification.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Dec 2015 11:12:15 +0000 (12:12 +0100)]
net: introduce change lower state notifier
When lower device like bonding slave, team/bridge port, etc changes its
state, it is useful for others to notice this change. Currently this is
implemented specificly for bonding as NETDEV_BONDING_INFO notifier. This
patch aims to replace this specific usage and make this more generic to
be used for all upper-lower devices.
Introduce NETDEV_CHANGELOWERSTATE netdev notifier type and
netdev_lower_state_changed() helper.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Dec 2015 11:12:14 +0000 (12:12 +0100)]
bonding: fill-up LAG changeupper info struct and pass it along
Initialize netdev_lag_upper_info structure by TX type according to
current bonding mode and pass it along via netdev_master_upper_dev_link.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Dec 2015 11:12:11 +0000 (12:12 +0100)]
net: add possibility to pass information about upper device via notifier
Sometimes the drivers and other code would find it handy to know some
internal information about upper device being changed. So allow upper-code
to pass information down to notifier listeners during linking.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 3 Dec 2015 11:12:04 +0000 (12:12 +0100)]
net: Add support for CHANGEUPPER notifier error injection
Since CHANGEUPPER can now fail, add support for it in the newly
introduced netdev notifier error injection infrastructure.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 3 Dec 2015 11:12:03 +0000 (12:12 +0100)]
net: Check CHANGEUPPER notifier return value
switchdev drivers reflect the newly requested topology to hardware when
CHANGEUPPER is received, after software links were already formed.
However, the operation can fail and user will not be notified, as the
return value of the notifier is not checked.
Add this check and rollback software links if necessary.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 3 Dec 2015 12:20:57 +0000 (04:20 -0800)]
i40e: Fix i40e_print_features() VEB mode output
Commit 7fd89545f337 ("i40e: remove BUG_ON from feature string building")
added defective output when I40E_FLAG_VEB_MODE_ENABLED was set in
function i40e_print_features.
Fix it.
Miscellanea:
- Remove unnecessary string variable
- Add space before not after fixed strings
- Use kmalloc not kzalloc
- Don't initialize i to 0, use result of first snprintf
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 3 Dec 2015 16:43:32 +0000 (11:43 -0500)]
Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-12-03
This series contains updates to ixgbe and ixgbevf only.
Mark cleans up ixgbe_init_phy_ops_x550em, since this was designed to
initialize function pointers only and moves the KR PHY reset to the
ixgbe_setup_internal_phy_t_x550em which was designed to detect which
mode the PHY operates in and set it up. Added the new thermal alarm
type support used with newer X550EM_x devices. Fixed both ixgbe and
ixgbevf to use a private work queue to avoid hangs, which would
possibly occur when creating and destroying many VFS repeatedly.
Updated ixgbe PTP implementation to accommodate X550EM_x devices,
which handle clocking differently. Fixed specification violations
in the datasheet, which was reported by Dan Streetman. Fixed ixgbe
to check for and handle IPv6 extended headers so that Tx checksum
offload can be done, which was reported by Tom Herbert. Fixed ixgbe
link issue for some systems with X540 or X550 by only inhibiting the
turning PHY power off when manageability is present.
Alex Duyck refactors the MAC address configuration code, which in
turns fixes an issue where once 63 entries had been used, you could no
longer add additional filters. Updated ixgbe to use __dev_uc_sync
which also resolved an issue in which you could not remove an FDB
address without having to reset the port. Updated the ixgbe driver
to make use of all the free RAR entries for FDB use if needed.
v2: updated patch 13 to "Alex Duyck Approved" version, in the original
submission, I had grabbed a previous version of the patch and did not
catch it was superseded by a later version
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Rustad [Thu, 19 Nov 2015 21:56:30 +0000 (13:56 -0800)]
ixgbevf: Handle extended IPv6 headers in Tx path
Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for seeing how to coalesce the error handling
into one location.
Reported-by: Tom Herbert <tom@herbertland.com> Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Thu, 5 Nov 2015 19:02:14 +0000 (11:02 -0800)]
ixgbe: Always turn PHY power on when requested
Instead of inhibiting PHY power control when manageability is
present, only inhibit turning PHY power off when manageability
is present. Consequently, PHY power will always be turned on when
requested. Without this patch, some systems with X540 or X550
devices in some conditions will never get link.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Wed, 18 Nov 2015 17:21:28 +0000 (09:21 -0800)]
ixgbe: Handle extended IPv6 headers in Tx path
Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for recognizing problems with the first version
of this patch and recognizing how to coalesce error conditions
into a single location.
Reported-by: Tom Herbert <tom@herbertland.com> Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Fri, 30 Oct 2015 22:29:34 +0000 (15:29 -0700)]
ixgbe: Save VF info and take references
Save VF device pointers and take references to speed accesses used
to monitor the device behavior to avoid slot resets. The saved
information avoids lock contention during the search used to access
each of the VFs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Tue, 27 Oct 2015 20:23:23 +0000 (13:23 -0700)]
ixgbe: Wait for master disable to be set
According to the datasheets, the driver should wait for the master
disable bit to read as being set before checking the status
register for master disable.
Reported-by: Dan Streetman <dan.streetman@canonical.com> Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Tue, 27 Oct 2015 20:23:14 +0000 (13:23 -0700)]
ixgbe: Correct spec violations by waiting after reset
The ixgbe driver was violating the specification in the datasheet
by not waiting 1ms before checking for the reset bit clearing. This
is called out for devices supported by ixgbe, so implement the
required delay.
Reported-by: Dan Streetman <dan.streetman@canonical.com> Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Tue, 27 Oct 2015 16:58:07 +0000 (09:58 -0700)]
ixgbe: Update PTP to support X550EM_x devices
The X550EM_x devices handle clocking differently, so update the
PTP implementation to accommodate them. This involves significant
changes to ixgbe's PTP code to accommodate the new range of
behaviors including things like non-power-of-2 clock wrapping.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 22 Oct 2015 23:26:42 +0000 (16:26 -0700)]
ixgbe: Allow FDB entries access to more RAR filters
This change makes it so that we allow the PF to make use of all free RAR
entries for FDB use if needed.
Previously the code limited us to 16 unicast entries, however this was
shared between MACVLAN which wasn't limited and the FDB code which was. So
instead of treating the FDB code as a second class citizen I have updated
it so that it has access to just as many entries as the MACVLAN filters.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 22 Oct 2015 23:26:36 +0000 (16:26 -0700)]
ixgbe: Use __dev_uc_sync and __dev_uc_unsync for unicast addresses
This change replaces the ixgbe_write_uc_addr_list call in ixgbe_set_rx_mode
with a call to __dev_uc_sync instead. This works much better with the MAC
addr list code that was already in place and solves an issue in which you
couldn't remove an FDB address without having to reset the port.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 22 Oct 2015 23:26:30 +0000 (16:26 -0700)]
ixgbe: Refactor MAC address configuration code
In the process of tracking down a memory leak when adding/removing FDB
entries I had to go through the MAC address configuration code for ixgbe.
In the process of doing so I found a number of issues that impacted
readability and performance. This change updates the code in general to
clean it up so it becomes clear what each step is doing. From what I can
tell there a couple of bugs cleaned up in this code.
First is the fact that the MAC addresses were being double counted for the
PF. As a result once entries up to 63 had been used you could no longer
add additional filters.
A simple test case for this:
for i in `seq 0 96`
do
ip link add link ens8 name mv$i type macvlan
ip link set dev mv$i up
done
When things are working correctly RAL/H registers 1 - 97 will be consumed.
In the failing case it will stop at 63 and prevent any further filters from
being added.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Thu, 22 Oct 2015 00:21:20 +0000 (17:21 -0700)]
ixgbevf: Minor cleanups
Make some minor cleanups, such as simplifying return paths, deleting
unneeded initializations, return values more directly and so forth.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Thu, 22 Oct 2015 00:21:15 +0000 (17:21 -0700)]
ixgbevf: Use a private workqueue to avoid certain possible hangs
Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Thu, 22 Oct 2015 00:21:10 +0000 (17:21 -0700)]
ixgbe: Use private workqueue to avoid certain possible hangs
Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Mon, 19 Oct 2015 16:22:14 +0000 (09:22 -0700)]
ixgbe: Add support for newer thermal alarm
The newer copper PHY implementation used with newer X550EM_x
devices uses a different thermal alarm type than the earlier
one. Make changes to support both types.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Fri, 16 Oct 2015 20:27:49 +0000 (13:27 -0700)]
ixgbe: Prevent KR PHY reset in ixgbe_init_phy_ops_x550em
This patch removes KR PHY reset from ixgbe_init_phy_ops_x550em,
since this function is meant to initialize function pointers for
the detected PHY type. Internal PHY reset was moved to
ixgbe_setup_internal_phy_t_x550em which will now detect which
mode the internal PHY operates in and set it up as required.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jarod Wilson [Mon, 30 Nov 2015 22:12:21 +0000 (17:12 -0500)]
sfc: use ALIGN macro for aligning frame sizes
Don't open-code it.
CC: Solarflare linux maintainers <linux-net-drivers@solarflare.com> CC: Shradha Shah <sshah@solarflare.com> CC: netdev@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Acked-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 30 Nov 2015 16:57:28 +0000 (08:57 -0800)]
tcp: suppress too verbose messages in tcp_send_ack()
If tcp_send_ack() can not allocate skb, we properly handle this
and setup a timer to try later.
Use __GFP_NOWARN to avoid polluting syslog in the case host is
under memory pressure, so that pertinent messages are not lost under
a flood of useless information.
sk_gfp_atomic() can use its gfp_mask argument (all callers currently
were using GFP_ATOMIC before this patch)
We rename sk_gfp_atomic() to sk_gfp_mask() to clearly express this
function now takes into account its second argument (gfp_mask)
Note that when tcp_transmit_skb() is called with clone_it set to false,
we do not attempt memory allocations, so can pass a 0 gfp_mask, which
most compilers can emit faster than a non zero or constant value.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 3 Dec 2015 04:43:48 +0000 (23:43 -0500)]
Merge branch 'hv_netvsc-less-headroom'
Merge branch 'hv_netvsc-less-headroom'
K. Y. Srinivasan says:
====================
hv_netvsc: Eliminate the additional head room
In an attempt to avoid having to allocate memory on the send path, the netvsc
driver was requesting additional head room so that both rndis header and the
netvsc packet (the state that had to persist) could be placed in the skb.
Since the amount of head room requested was exceeding the default head room
as set in LL_MAX_HEADER, we were forcing a reallocation of skb.
With this patch-set, I have reduced the size of the netvsc packet to less
than 20 bytes and with this reduction we don't need to ask for any additional
headroom. We place the rndis header in the skb head room and we place the
netvsc packet in control buffer area in the skb.
V2: - Addressed review comments:
- Eliminated more fields from netvsc packet structure.
V3: - Fixed a typo in patch: hv_netvsc: Don't ask for additional head room in the skb.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:13 +0000 (16:43 -0800)]
hv_netvsc: Eliminate page_buf from struct hv_netvsc_packet
Eliminate page_buf from struct hv_netvsc_packet.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Packet scheduler guarantees there won't be multiple senders for the same
queue and as we use q_idx for multi_send_data the spinlock is redundant.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
hv_netvsc: move subchannel existence check to netvsc_select_queue()
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:10 +0000 (16:43 -0800)]
hv_netvsc: Don't ask for additional head room in the skb
The rndis header is 116 bytes big and can be placed in the default
head room that will be available in the skb. Since the netvsc packet
is less than 48 bytes, we can use the skb control buffer
for the netvsc packet. With these changes we don't need to
ask for additional head room.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:09 +0000 (16:43 -0800)]
hv_netvsc: Eliminate send_completion_ctx from struct hv_netvsc_packet
Eliminate send_completion_ctx from struct hv_netvsc_packet.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:08 +0000 (16:43 -0800)]
hv_netvsc: Eliminate send_completion from struct hv_netvsc_packet
Eliminate send_completion from struct hv_netvsc_packet.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:07 +0000 (16:43 -0800)]
hv_netvsc: Eliminatte the data field from struct hv_netvsc_packet
Eliminatte the data field from struct hv_netvsc_packet.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:06 +0000 (16:43 -0800)]
hv_netvsc: Eliminate rndis_msg pointer from hv_netvsc_packet structure
Eliminate rndis_msg pointer from hv_netvsc_packet structure.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:05 +0000 (16:43 -0800)]
hv_netvsc: Eliminate the channel field in hv_netvsc_packet structure
Eliminate the channel field in hv_netvsc_packet structure.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:04 +0000 (16:43 -0800)]
hv_netvsc: Rearrange the hv_negtvsc_packet to be space efficient
Rearrange the elements of struct hv_negtvsc_packet for optimal layout -
eliminate unnecessary padding.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:03 +0000 (16:43 -0800)]
hv_netvsc: Resize some of the variables in hv_netvsc_packet
As part of reducing the size of the hv_netvsc_packet, resize some of the
variables based on their usage.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 2 Dec 2015 20:32:50 +0000 (15:32 -0500)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-12-01
This series contains updates to i40e and i40evf only.
Helin adds new fields to i40e_vsi to store user configured RSS config data
and the code to use it. Also renamed RSS items to clarify functionality
and scope to users. Fixed a confusing kernel message of enabling RSS size
by reporting it together with the hardware maximum RSS size.
Anjali fixes the issue of forcing writeback too often causing us to not
benefit from NAPI.
Jesse adds a prefetch for data early in the transmit path to help immensely
for pktgen and forwarding workloads. Fixed the i40e driver that was
possibly sleeping inside critical section of code.
Carolyn fixes an issue where adminq init failures always provided a message
that NVM was newer than expected, when this is not always the case for
init_adminq failures. Fixed by adding a check for that specific error
condition and a different helpful message otherwise.
Mitch fixes error message by telling the user which VF is being naughty,
rather than making them guess. Updated the queue_vector array from a
statically-sized member of the adapter structure, to a dynamically-allocated
and -sized array. This reduces the size of the adapter structure and allows
us to support any number of queue vectors in the future without changing the
code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With the final edition of the patches to remove sleeps from
the driver's entry points, the grab_rtnl argument is no
longer needed, so partially revert the commit that added it.
Change-ID: Ib9778476242586cc9e58b670f5f48d415cb59003 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was being called by VLAN, bonding, teaming operations
that expected to be able to hold locks like rcu_read_lock().
This causes the driver to be held to the requirement to not sleep,
and was found by the kernel debug options for checking sleep
inside critical section, and the locking validator.
Change-ID: Ibc68c835f5ffa8ffe0638ffe910a66fc5649a7f7 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Mon, 26 Oct 2015 23:44:40 +0000 (19:44 -0400)]
i40evf: allocate ring structs dynamically
Instead of awkwardly keeping a fixed array of pointers in the adapter
struct and then allocating ring structs individually, just keep a single
pointer and allocate a single blob for the arrays. This simplifies code,
shrinks the adapter structure, and future-proofs the driver by not
limiting the number of rings we can handle.
Change-ID: I31334ff911a6474954232cfe4bc98ccca3c769ff Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Mon, 26 Oct 2015 23:44:39 +0000 (19:44 -0400)]
i40evf: allocate queue vectors dynamically
Change the queue_vector array from a statically-sized member of the
adapter structure to a dynamically-allocated and -sized array.
This reduces the size of the adapter structure, and allows us to support
any number of queue vectors in the future without changing the code.
Change-ID: I08dc622cb2f2ad01e832e51c1ad9b86524730693 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Mon, 26 Oct 2015 23:44:38 +0000 (19:44 -0400)]
i40evf: quoth the VF driver, Nevermore
If, upon a midnight dreary, the PF returns ERR_PARAM when the VF is
requesting resources, that's fatal. Either the firmware or NVM is badly,
badly misconfigured, or this VF has been disabled due to a previous VF
driver sending a bunch of bogus messages.
Either way, there is no recovery from this. Don't ponder weak and weary,
just quit.
Change-ID: I09d9f16cc4ee7fec3b57646a289d33838c1c5bf5 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Mon, 26 Oct 2015 23:44:37 +0000 (19:44 -0400)]
i40e: make error message more useful
If we get an invalid message from a VF, we should tell the user which VF
is being naughty, rather than making them guess.
Change-ID: I9252cef7baea3d8584043ed6ff12619a94e2f99c Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Mon, 26 Oct 2015 23:44:35 +0000 (19:44 -0400)]
i40e: Update error messaging
This patch fixes an issue where adminq init failures always provided
a message that NVM was newer than expected. This is not always the
case for init_adminq failures. Without this patch, if adminq init
fails for any reason, newer NVM message would be given. This
problem is fixed by adding a check for that specific error
condition and a different hopefully helpful message otherwise.
Change-ID: Iaeaebee4e398989eae40bb70f943ab66a3a521a5 Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Helin Zhang [Mon, 26 Oct 2015 23:44:33 +0000 (19:44 -0400)]
i40evf: create a generic get RSS function
There are two ways to get RSS, this patch implements two functions
with the same input parameters, and creates a more generic function
for getting RSS configuration.
Change-ID: I12d3b712c21455d47dd0a5aae58fc9b7c680db59 Signed-off-by: Helin Zhang <helin.zhang@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Helin Zhang [Tue, 27 Oct 2015 20:15:06 +0000 (16:15 -0400)]
i40evf: create a generic config RSS function
There are two ways to configure RSS, this patch adjusts those two
functions with the same input parameters, and creates a more
generic function for configuring RSS.
Change-ID: Iace73bdeba4831909979bef221011060ab327f71 Signed-off-by: Helin Zhang <helin.zhang@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jesse Brandeburg [Mon, 26 Oct 2015 23:44:30 +0000 (19:44 -0400)]
i40e/i40evf: prefetch skb data on transmit
Issue a prefetch for data early in the transmit path.
This should not be generally needed for Tx traffic, but
it helps immensely for pktgen workloads and should help
for forwarding workloads as well.
Change-ID: Iefee870c20599e0c4240e1d8637e4f16b625f83a Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e/i40evf: Fix RS bit update in Tx path and disable force WB workaround
This patch fixes the issue of forcing WB too often causing us to not
benefit from NAPI.
Without this patch we were forcing WB/arming interrupt too often taking
away the benefits of NAPI and causing a performance impact.
With this patch we disable force WB in the clean routine for X710
and XL710 adapters. X722 adapters do not enable interrupt to force
a WB and benefit from WB_ON_ITR and hence force WB is left enabled
for those adapters.
For XL710 and X710 adapters if we have less than 4 packets pending
a software Interrupt triggered from service task will force a WB.
This patch also changes the conditions for setting RS bit as described
in code comments. This optimizes when the HW does a tail bump amd when
it does a WB. It also optimizes when we do a wmb.
Change-ID: Id831e1ae7d3e2ec3f52cd0917b41ce1d22d75d9d Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Helin Zhang [Mon, 26 Oct 2015 23:44:28 +0000 (19:44 -0400)]
i40e: rename rss_size to alloc_rss_size in i40e_pf
This patch renames rss_size to alloc_rss_size in i40e_pf, which is
clearer and avoids confusion. It also adds comments to the other
related structure members to help clarify usage.
Change-ID: Ia90090609d006ab589cb639975bb8a0af795d16f Signed-off-by: Helin Zhang <helin.zhang@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Arnd Bergmann [Mon, 30 Nov 2015 10:34:09 +0000 (11:34 +0100)]
isdn: remove spellcaster driver
The 'sc' ISDN driver relies on using readl() to access ISA I/O memory.
This has been deprecated and produced warnings since linux-2.3.23,
disabled by default since 2.4.10 and finally removed in 2.6.5.
I found this because the compiling the driver for ARM produces
a warning:
In file included from ../drivers/isdn/sc/includes.h:8:0,
from ../drivers/isdn/sc/init.c:13:
../arch/arm/include/asm/io.h:115:21: note: expected 'const volatile void *' but argument is of type 'long unsigned int'
It is pretty clear that this driver has not been used for a long time
and there is no point fixing it now, so let's remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
For GMAC newer than 3.40a there is a new register (Reg_9) that provides the
status of all modules of the transmit and receive paths and FIFO status.
These can be exposed via ethtool.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 1 Dec 2015 21:02:41 +0000 (16:02 -0500)]
Merge branch 'qed-ethtool-ops'
Yuval Mintz says:
====================
qede/qed: Implement various ethtool operations
This series adds several new ethtool operations to qede:
- {get, set}_channels
- {get, set}_ringparam
- set_phys_id
- nway_reset
- {get, set}_pauseparam
As well as extending the qed APIs to support these commands.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Physical LEDs are being controlled by the management FW.
This adds the qed functionality required to request management FW to
change the LED configuration, as well as the necessary APIs for this
functionality to later be used by the protocol drivers.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 1 Dec 2015 20:46:40 +0000 (15:46 -0500)]
Merge branch 'sfc-8000'
Bert Kenward says:
====================
Basic support for Solarflare 8000 series NICs
The upcoming Solarflare 8000 series 10G/40G network card supports a
similar interface to the current 7000 series cards. This patch series
provides basic support for these cards, making no use of any new
functionality.
v2: fix indenting in ef10.c in patch 1/2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bert Kenward [Mon, 30 Nov 2015 09:05:35 +0000 (09:05 +0000)]
sfc: make TSO version a per-queue parameter
The Solarflare 8000 series NIC will use a new TSO scheme. The current
driver refuses to load if the current TSO scheme is not found. Remove
that check and instead make the TSO version a per-queue parameter.
Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log