Dan Carpenter [Tue, 6 Apr 2010 16:31:26 +0000 (19:31 +0300)]
ALSA: mixart: range checking proc file
The original code doesn't take into consideration that the value of
MIXART_BA0_SIZE - pos can be less than zero which would lead to a large
unsigned value for "count".
Also I moved the check that read size is a multiple of 4 bytes below
the code that adjusts "count".
ALSA: hda - Fix a wrong array range check in patch_realtek.c
The commit 6a4f2ccb467e00281470cde2dee08fe5ecde62d1 introduced a wrong
comparision for the array range check, which effectively skips the whole
initialization of DAC connections. Fixed now.
Daniel Mack [Mon, 22 Mar 2010 09:11:15 +0000 (10:11 +0100)]
ALSA: ASoC: move dma_data from snd_soc_dai to snd_soc_pcm_stream
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.
All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.
[Note that this is a backported version for 2.6.34.
Upstream commit is fd23b7dee]
Signed-off-by: Daniel Mack <daniel@caiaq.de> Reported-by: Sven Neumann <s.neumann@raumfeld.com> Reported-by: Michael Hirsch <m.hirsch@raumfeld.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tony Vroon [Mon, 5 Apr 2010 15:30:43 +0000 (16:30 +0100)]
ALSA: hda - Enable amplifiers on Acer Inspire 6530G
After more tests it appears that EAPD needs to be enabled
on both the 0x14 and 0x15 NIDs to enable the main speaker
and headphone amplifiers. The maximum volume setting is
now equal to what the machine achieves under other operating
systems.
Disabling Front or LFE playback triggers EAPD and disables
the amplifier. As such, these two playback switches have
been removed from the mixer.
Signed-off-by: Tony Vroon <tony@linx.net> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mark Brown [Mon, 29 Mar 2010 16:18:41 +0000 (17:18 +0100)]
ASoC: Don't use DCS_DATAPATH_BUSY for WM hubs devices
The DCS_DATAPATH_BUSY bit used to monitor the completion of DC servo
operations has been deprecated and with some more recente revisions
may perform incorrectly, especially when only analogue bypass paths
are in use. Switch to using readback from the DC servo command
register instead, which is supported for all devices. Without this
unacceptably long timeouts may be observed in some circumstances.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Mon, 29 Mar 2010 15:34:42 +0000 (16:34 +0100)]
ASoC: Don't do runtime wm_hubs DC servo updates if using offset correction
If we need to offset correct the DC servo then don't use runtime
recalibration since that is likely to introduce further offsets
which will be evident on powerdown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Mon, 29 Mar 2010 16:09:45 +0000 (17:09 +0100)]
ASoC: Support second DC servo readback method for wm_hubs
More recent Wolfson hubs devices add the ability to read back the DC
servo calibration information from the register used to write offsets,
and later still ones remove the old readback registers. Add support
for the new scheme, and use it for WM8994 device revisions that
support it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
ASoC: OMAP: Fix capture pointer handling for OMAP1510 to work correctly with recent ALSA PCM code
With recent (2.6.34) chnages in PCM handling, capture stopped working on my
OMAP1510 based Amstrad Delta videophone.
Using 2.6.34-rc2, I was able to correct the problem in 3 different ways:
1. reverting commit 7b3a177b0d4f92b3431b8dca777313a07533a710,
2. enabling additional jiffies check with
echo 4 >/proc/asound/card0/pcm0c0/xrun_debug
3. applying the patch below.
Since I wasn't able to reproduce the problem on my i686 PC, I guess the
problem is probably machine specific.
The patch reuses the method for software emulation of missing hardware
pointer, already implemented for playback on OMAP1510. It's possible that
event if a hardware pointer is available for capture on this machine, its
behaviour may be not compatible with what upper layer expects.
If you think the problem may be more general and should be solved differently,
on a higher level, I can try to work more on it if you give me a hint.
If the patch gets accepted, I suggest it goes as a fix in the current release
cycle.
Created and tested against linux-2.6.34-rc2.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Daniel T Chen [Tue, 30 Mar 2010 17:29:28 +0000 (13:29 -0400)]
ALSA: hda: Fix 0 dB offset for Lenovo Thinkpad models using AD1981
BugLink: https://launchpad.net/bugs/551606
The OR's hardware distorts at PCM 100% because it does not correspond to
0 dB. Fix this in patch_ad1981() for all models using the Thinkpad
quirk.
Reported-by: Jane Silber Cc: <stable@kernel.org> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Graham Gower [Thu, 25 Mar 2010 00:22:12 +0000 (10:52 +1030)]
ASoC: Fix passing platform_data to ac97 bus users and fix a leak
[The issue is an attempt to write the pdata without the AC97 device
allocated when using ac97.c - also added a comment in soc-core.c for the
special case for ac97. -- broonie]
Signed-off-by: Graham Gower <graham.gower@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Takashi Iwai [Mon, 29 Mar 2010 15:21:45 +0000 (17:21 +0200)]
ALSA: hda - Fix ADC/MUX assignment of ALC269 codec
ALC269 codec has a few different variants, and each of them may have
different ADC and MUX widgets. For example, one model has ADC 0x08
with MUX 0x23 while others has ADC 0x09 or ADC 0x07 with MUX 022 or
0x24. The difference of ADC appears usually as the capability of
the digital mic pin (0x12), and the current driver sometimes misses
the internal mic pin due to the mismatching ADC.
This patch adds a bit more clever way to find the matching ADC instead
of the static list. Now the driver checks all active input pins and
fills only the ADC/MUX's that contain all of them.
Takashi Iwai [Mon, 29 Mar 2010 07:16:24 +0000 (09:16 +0200)]
ALSA: hda - Fix invalid bit values passed to snd_hda_codec_amp_stereo()
The mask and value parameters passed to snd_hda_codec_amp_stereo()
should be 8-bit values for mute and volume. Passing AMP_IN_MUTE() is
wrong, which is found in many places in patch_realtek.c as a left-over
from the conversion to snd_hda_codec_amp_stereo().
Reported-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reported-by: Carlos Laviola <claviola@debian.org> Tested-by: Carlos Laviola <claviola@debian.org> Cc: <stable@kernel.org> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Daniel Chen [Sun, 28 Mar 2010 20:32:34 +0000 (13:32 -0700)]
ALSA: ac97: Add Toshiba P500 to ac97 jack sense blacklist
BugLink: https://launchpad.net/bugs/481058
The OR has verified that both 'Headphone Jack Sense' and 'Line Jack Sense'
need to be muted for sound to be audible, so just add the machine's SSID
to the ac97 jack sense blacklist.
Reported-by: Richard Gagne Tested-by: Richard Gagne Cc: <stable@kernel.org> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jarkko Nikula [Fri, 26 Mar 2010 14:07:25 +0000 (16:07 +0200)]
ALSA: pcm_lib - fix xrun functionality
The commit 4d96eb255c53ab5e39b37fd4d484ea3dc39ab456 broke the interrupt
time xrun functionality (stream stop etc.) if the CONFIG_SND_PCM_XRUN_DEBUG
is not set. This is because the xrun() is null defined without it.
Fix this by letting the function xrun() to be always defined as it was
before.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Cc: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Daniel T Chen [Fri, 26 Mar 2010 05:38:15 +0000 (22:38 -0700)]
ALSA: ac97: Add IBM ThinkPad R40e to Headphone/Line Jack Sense blacklist
BugLink: https://launchpad.net/bugs/303789
This model needs both 'Headphone Jack Sense' and 'Line Jack Sense'
muted for audible audio, so just add its SSID to the blacklist and
don't enumerate the controls.
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dan Carpenter [Wed, 24 Mar 2010 11:58:34 +0000 (14:58 +0300)]
ASoC: wm8994: playback => capture
Sparse caught that initialize "playback" two times instead of
initializing "capture".
Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Clemens Ladisch [Wed, 24 Mar 2010 06:10:54 +0000 (07:10 +0100)]
ALSA: cmipci: work around invalid PCM pointer
When the CMI8738 FRAME2 register is read, the chip sometimes (probably
when wrapping around) returns an invalid value that would be outside the
programmed DMA buffer. This leads to an inconsistent PCM pointer that is
likely to result in an underrun.
To work around this, read the register multiple times until we get a
valid value; the error state seems to be very short-lived.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-and-tested-by: Matija Nalis <mnalis-alsadev@voyager.hr> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Daniel T Chen [Sun, 21 Mar 2010 22:34:43 +0000 (18:34 -0400)]
ALSA: hda: Fix 0 dB offset for HP laptops using CX20551 (Waikiki)
BugLink: https://launchpad.net/bugs/420578
The OR has verified that his hardware distorts because of the 0 dB
offset not corresponding to the highest PCM level. Fix this by capping
said PCM level to 0 dB similarly to what we do for CX20549 (Venice).
Reported-by: Mike Pontillo <pontillo@gmail.com> Tested-by: Mike Pontillo <pontillo@gmail.com> Cc: <stable@kernel.org> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Julia Lawall [Thu, 18 Mar 2010 06:53:11 +0000 (07:53 +0100)]
sound/oss/vidc.c: change the field used with DMA_ACTIVE
The constant DMA_ACTIVE is defined with the dma_buffparams structure rather
than with the audio_operations structure. Takashi Iwai suggested that the
dmap_out field of the audio_operations structure should be used instead.
This is not tested.
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Takashi Iwai <tiwai@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
serial: sh-sci: remove duplicated #include
sh: Export uncached helper symbols.
sh: Fix up NUMA build for 29-bit.
serial: sh-sci: Fix build failure for non-sh architectures.
sh: Fix up uncached offset for legacy 29-bit mode.
sh: Support CPU affinity masks for INTC controllers.
Linus Torvalds [Fri, 19 Mar 2010 20:49:29 +0000 (13:49 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: fix compile errors in dma-mapping-common.h
alpha: remove trailing spaces in messages
alpha: use __ratelimit
Linus Torvalds [Fri, 19 Mar 2010 20:42:43 +0000 (13:42 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Remove IOMMU_VMERGE config option
powerpc: Fix swiotlb to respect the boot option
powerpc: Do not call prink when CONFIG_PRINTK is not defined
powerpc: Use correct ccr bit for syscall error status
powerpc/fsl-booke: Get coherent bit from PTE
powerpc/85xx: Make sure lwarx hint isn't set on ppc32
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty_port,usb-console: Fix usb serial console open/close regression
tty: cpm_uart: use resource_size()
tty_buffer: Fix distinct type warning
hvc_console: Fix race between hvc_close and hvc_remove
uartlite: Fix build on sparc.
tty: Take a 256 byte padding into account when buffering below sub-page units
Revert "tty: Add a new VT mode which is like VT_PROCESS but doesn't require a VT_RELDISP ioctl call"
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
driver core: numa: fix BUILD_BUG_ON for node_read_distance
driver-core: document ERR_PTR() return values
kobject: documentation: Update to refer to kset-example.c.
sysdev: the cpu probe/release attributes should be sysdev_class_attributes
kobject: documentation: Fix erroneous example in kobject doc.
driver-core: fix missing kernel-doc in firmware_class
Driver core: Early platform kernel-doc update
sysfs: fix sysfs lockdep warning in mlx4 code
sysfs: fix sysfs lockdep warning in infiniband code
sysfs: fix sysfs lockdep warning in ipmi code
sysfs: Initialised pci bus legacy_mem field before use
sysfs: use sysfs_bin_attr_init in firmware class driver
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (45 commits)
USB: gadget/multi: cdc_do_config: remove redundant check
usb: r8a66597-hcd: fix removed from an attached hub
USB: xhci: Make endpoint interval debugging clearer.
USB: Fix usb_fill_int_urb for SuperSpeed devices
USB: cp210x: Remove double usb_control_msg from cp210x_set_config
USB: Remove last bit of CONFIG_USB_BERRY_CHARGE
USB: gadget: add gadget controller number for s3c-hsotg driver
USB: ftdi_sio: Fix locking for change_speed() function
USB: g_mass_storage: fixed module name in Kconfig
USB: gadget: f_mass_storage::fsg_bind(): fix error handling
USB: g_mass_storage: fix section mismatch warnings
USB: gadget: fix Blackfin builds after gadget cleansing
USB: goku_udc: remove potential null dereference
USB: option.c: Add Pirelli VID/PID and indicate Pirelli's modem interface is 0xff
USB: serial: Fix module name typo for qcaux Kconfig entry.
usb: cdc-wdm: Fix deadlock between write and resume
usb: cdc-wdm: Fix order in disconnect and fix locking
usb: cdc-wdm:Fix loss of data due to autosuspend
usb: cdc-wdm: Fix submission of URB after suspension
usb: cdc-wdm: Fix race between disconnect and debug messages
...
Linus Torvalds [Fri, 19 Mar 2010 16:43:06 +0000 (09:43 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (205 commits)
ceph: update for write_inode API change
ceph: reset osd after relevant messages timed out
ceph: fix flush_dirty_caps race with caps migration
ceph: include migrating caps in issued set
ceph: fix osdmap decoding when pools include (removed) snaps
ceph: return EBADF if waiting for caps on closed file
ceph: set osd request message front length correctly
ceph: reset front len on return to msgpool; BUG on mismatched front iov
ceph: fix snaptrace decoding on cap migration between mds
ceph: use single osd op reply msg
ceph: reset bits on connection close
ceph: remove bogus mds forward warning
ceph: remove fragile __map_osds optimization
ceph: fix connection fault STANDBY check
ceph: invalidate_authorizer without con->mutex held
ceph: don't clobber write return value when using O_SYNC
ceph: fix client_request_forward decoding
ceph: drop messages on unregistered mds sessions; cleanup
ceph: fix comments, locking in destroy_inode
ceph: move dereference after NULL test
...
Fix trivial conflicts in Documentation/ioctl/ioctl-number.txt
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: trivial white space
[CIFS] checkpatch cleanup
cifs: add cifs_revalidate_file
cifs: add a CIFSSMBUnixQFileInfo function
cifs: add a CIFSSMBQFileInfo function
cifs: overhaul cifs_revalidate and rename to cifs_revalidate_dentry
Daniel Mack [Sun, 28 Feb 2010 02:42:38 +0000 (10:42 +0800)]
ASoC: pxa-pcm-lib: initialize DMA channel to -1
This fixes a warning ("pxa_free_dma: trying to free channel 0 which is
already freed") when a device was opened but the hw_params() call
failed.
Signed-off-by: Daniel Mack <daniel@caiaq.de> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sarah Sharp [Tue, 16 Mar 2010 19:59:24 +0000 (12:59 -0700)]
USB: xhci: Make endpoint interval debugging clearer.
The xHCI hardware can only handle polling intervals that are a power of
two. When we add a new endpoint during a bandwidth allocation, and the
polling interval is rounded down to a power of two, print the original
polling interval in the endpoint descriptor.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Wilcox [Tue, 16 Mar 2010 19:55:44 +0000 (12:55 -0700)]
USB: Fix usb_fill_int_urb for SuperSpeed devices
USB 3 and Wireless USB specify a logarithmic encoding of the endpoint
interval that matches the USB 2 specification. usb_fill_int_urb() didn't
know that and was filling in the interval as if it was USB 1.1. Fix
usb_fill_int_urb() for SuperSpeed devices, but leave the wireless case
alone, because David Vrabel wants to keep the old encoding.
Update the struct urb kernel doc to note that SuperSpeed URBs must have
urb->interval specified in microframes.
Add a missing break statement in the usb_submit_urb() interrupt URB
checking, since wireless USB and SuperSpeed USB encode urb->interval
differently. This allows xHCI roothubs to actually register with khubd.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Michael Brunner [Wed, 10 Mar 2010 22:26:37 +0000 (23:26 +0100)]
USB: cp210x: Remove double usb_control_msg from cp210x_set_config
This patch removes a double usb_control_msg that sets the cp210x
configuration registers a second time when calling cp210x_set_config.
For data sizes >2 the second write gets corrupted.
The patch has been created against 2.6.34-rc1, but all cp210x driver
revisions are affected.
Signed-off-by: Michael Brunner <mibru@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Contrary to the comment in fsg_add, fsg_bind calls fsg_unbind on errors,
which decreases refcount and frees the fsg_dev structure, causing trouble
when fsg_add does the same.
Fix it by simply leaving up cleanup to fsg_add().
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent commit (0e530b45783f75) that moved usb_ep_autoconfig from the
__devinit section to the __init section missed the mass storage device.
Its fsg_bind() function uses the usb_ep_autoconfig() function from non
__init context leading to:
WARNING: drivers/usb/gadget/g_mass_storage.o(.text): Section mismatch in
reference from the function _fsg_bind()
to the function .init.text:_usb_ep_autoconfig()
So move fsg_bind() into __init as well.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mike Frysinger [Tue, 9 Mar 2010 05:35:22 +0000 (00:35 -0500)]
USB: gadget: fix Blackfin builds after gadget cleansing
The recent change to clean out dead gadget drivers (90f7976880bbbf99)
missed the call to gadget_is_musbhsfc() behind CONFIG_BLACKFIN. This
causes Blackfin gadget builds to fail since the function no longer
exists anywhere.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mike Frysinger [Fri, 12 Mar 2010 08:27:23 +0000 (10:27 +0200)]
USB: musb: fix warnings in Blackfin regs
The recent commit "usb: musb: Add context save and restore support" added
some stubs for the Blackfin code so things would compile, but it also
added a bunch of warnings due to missing return statements.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mike Frysinger [Fri, 12 Mar 2010 08:27:21 +0000 (10:27 +0200)]
usb: musb: abstract out ULPI_BUSCONTROL register reads/writes
The USB PHY on current Blackfin processors is a UTMI+ level 2 PHY.
However, it has no ULPI support - so there are no registers at all.
That means accesses to ULPI_BUSCONTROL have to be abstracted away
like other MUSB registers.
This fixes building for Blackfin parts again.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Anand Gadiyar <gadiyar@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tony Lindgren [Fri, 12 Mar 2010 08:35:20 +0000 (10:35 +0200)]
usb: musb: Fix compile error for omaps for musb_hdrc
CONFIG_ARCH_OMAP34XX is now CONFIG_ARCH_OMAP3.
But since drivers/usb/musb/omap2430.c use CONFIG_PM for these
registers and functions, do the same for the header.
Otherwise we get the following for most omap3 defconfigs:
drivers/usb/musb/omap2430.c:261: error: expected identifier or '(' before 'do'
drivers/usb/musb/omap2430.c:261: error: expected identifier or '(' before 'while'
drivers/usb/musb/omap2430.c:268: error: expected identifier or '(' before 'do'
drivers/usb/musb/omap2430.c:268: error: expected identifier or '(' before 'while'
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andiry Xu [Fri, 12 Mar 2010 09:10:04 +0000 (17:10 +0800)]
USB: xHCI: re-initialize cmd_completion
When a signal interrupts a Configure Endpoint command, the cmd_completion used
in xhci_configure_endpoint() is not re-initialized and the
wait_for_completion_interruptible_timeout() will return failure. Initialize
cmd_completion in xhci_configure_endpoint().
Sonic Zhang [Mon, 8 Mar 2010 16:26:01 +0000 (11:26 -0500)]
USB: musb: fix build error introduced by isoc change
The recent commit "usb: musb: Fix for isochronous IN transfer" (f82a689fa)
seems to have been against an older kernel version. It uses the old style
naming of variables. Unfortunately, this breaks building for most MUSB
users out there since "bDesiredMode" has been renamed to "desired_mode".
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Acked-by: Anand Gadiyar <gadiyar@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clemens Ladisch [Mon, 1 Mar 2010 16:18:56 +0000 (17:18 +0100)]
USB: EHCI: adjust ehci_iso_stream for changes in ehci_qh
The EHCI driver stores in usb_host_endpoint.hcpriv a pointer to either
an ehci_qh or an ehci_iso_stream structure, and uses the contents of the
hw_info1 field to distinguish the two cases.
After ehci_qh was split into hw and sw parts, ehci_iso_stream must also
be adjusted so that it again looks like an ehci_qh structure.
This fixes a NULL pointer access in ehci_endpoint_disable() when it
tries to access qh->hw->hw_info1.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-by: Colin Fletcher <colin.m.fletcher@googlemail.com> Cc: stable <stable@kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clemens Ladisch [Mon, 1 Mar 2010 08:12:50 +0000 (09:12 +0100)]
USB: EHCI: fix ITD list order
When isochronous URBs are shorter than one frame and when more than one
ITD in a frame has been completed before the interrupt can be handled,
scan_periodic() completes the URBs in the order in which they are found
in the descriptor list. Therefore, the descriptor list must contain the
ITDs in the correct order, i.e., a new ITD must be linked in after any
previous ITDs of the same endpoint.
This should fix garbled capture data in the USB audio drivers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-by: Colin Fletcher <colin.m.fletcher@googlemail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johan Hovold [Sat, 27 Feb 2010 15:24:49 +0000 (16:24 +0100)]
USB: serial: use port endpoint size to determine if ep is available
It is possible to have a multi-port device with a port lacking an in or
out bulk endpoint. Only checking for num_bulk_in or num_bulk_out is thus not
sufficient to determine whether a specific port has an in or out bulk
endpoint.
This fixes potential null pointer dereferences in the generic open and
write routines, as well as access to uninitialised fifo in write_room
and chars_in_buffer.
Also let write fail with ENODEV (instead of 0) on missing out endpoint
(also on zero-length writes).
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sat, 6 Mar 2010 20:04:03 +0000 (15:04 -0500)]
USB: fix usbfs regression
This patch (as1352) fixes a bug in the way isochronous input data is
returned to userspace for usbfs transfers. The entire buffer must be
copied, not just the first actual_length bytes, because the individual
packets will be discontiguous if any of them are short.
Reported-by: Markus Rechberger <mrechberger@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jason Wessel [Tue, 9 Mar 2010 03:50:11 +0000 (21:50 -0600)]
tty_port,usb-console: Fix usb serial console open/close regression
Commit e1108a63e10d344284011cccc06328b2cd3e5da3 ("usb_serial: Use the
shutdown() operation") breaks the ability to use a usb console
starting in 2.6.33. This was observed when using
console=ttyUSB0,115200 as a boot argument with an FTDI device. The
error is:
The handling of the ASYNCB_INITIALIZED changed in 2.6.32 such that in
tty_port_shutdown() it always clears the flag if it is set. The fix
is to add a variable to the tty_port struct to indicate when the tty
port is a console.
CC: Alan Cox <alan@linux.intel.com> CC: Alan Stern <stern@rowland.harvard.edu> CC: Oliver Neukum <oliver@neukum.org> CC: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / mv-sheeva.git / log