Stephen Warren [Fri, 27 Dec 2013 02:43:10 +0000 (19:43 -0700)]
ARM: bcm2835: add USB controller to device tree
The BCM2835 SoC contains a DWC2 USB controller. Add this to the DT.
Set up the pin controller to fully enable the USB controller on the
Raspberry Pi. The GPIO setup works because the default output value for
GPIO 6 (LAN_RUN/n_reset) just happens to be 1, which enables the
USB/LAN chip.
Note that you'll need a U-Boot which enables power to the USB controller;
search for U-Boot patch "ARM: rpi_b: power on SDHCI and USB HW modules".
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Thu, 2 Jan 2014 20:05:13 +0000 (12:05 -0800)]
Merge tag 'sunxi-dt-for-3.14' of https://github.com/mripard/linux into next/dt
From Maxime Ripard:
Allwinner sunXi DT Additions for 3.14
Various DT related patches, but mostly:
- Support for the Olimex A13-olinuxino-micro
- Added the needed IP in the A31 for the HS timer support and SMP bringup
- A10 and A20 RTC
* tag 'sunxi-dt-for-3.14' of https://github.com/mripard/linux:
ARM: sun6i: dt: Add IP needed to bring up the additional cores
ARM: dts: sun5i: Add new sun5i-a13-olinuxino-micro board
ARM: sun6i: Add the reset controller to the DTSI
ARM: sunxi: dt: add EMAC aliases
ARM: dts: sun4i/sun7i: add RTC node
Olof Johansson [Thu, 2 Jan 2014 19:17:05 +0000 (11:17 -0800)]
Merge tag 'mvebu-dt-3.14-5' of git://git.infradead.org/linux-mvebu into next/dt
From Jason Cooper:
mvebu DT changes for v3.14 (incremental #5)
- mvebu
- add rtc chip isl12057 node to ReadyNAS boards
- fix register length in Armada XP pmsu
- kirkwood
- sort ocp nodes by address in 6282 dtsi file
- add 6192 dtsi file
- add LaPlug board
- add sata phy node
- dove
- add sata phy node
* tag 'mvebu-dt-3.14-5' of git://git.infradead.org/linux-mvebu:
ARM: Kirkwood: DT board setup for LaPlug
ARM: Kirkwood: Add 6192 DTSI file
ARM: mvebu: fix register length for Armada XP PMSU
ARM: kirkwood: 6282: sort DT nodes by address
Phy: Add DT nodes on kirkwood and Dove for the SATA PHY
ARM: mvebu: Enable ISL12057 RTC chip in ReadyNAS 2120 .dts file
ARM: mvebu: Enable ISL12057 RTC chip in ReadyNAS 104 .dts file
ARM: mvebu: Enable ISL12057 RTC chip in ReadyNAS 102 .dts file
Stephen Boyd [Fri, 20 Dec 2013 19:09:17 +0000 (11:09 -0800)]
ARM: msm: Simplify ARCH_MSM_DT config
This doesn't need to be a def_bool y. Instead we can have every
DT supported platform select ARCH_MSM_DT and we achieve the same
thing with less chance of conflicts.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Rohit Vaswani [Fri, 20 Dec 2013 19:09:15 +0000 (11:09 -0800)]
ARM: msm: Add support for MSM8974 SoC
Add support for the Snapdragon 800 MSM8974 SoC, used on the Dragonboard
and others. Board support added in separate patch.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org> Acked-by: Kumar Gala <galak@codeaurora.org> Signed-off-by: David Brown <davidb@codeaurora.org>
[olof: split off SoC support in separate patch] Signed-off-by: Olof Johansson <olof@lixom.net>
Josh Cartwright [Fri, 20 Dec 2013 19:09:14 +0000 (11:09 -0800)]
ARM: msm: trout: fix uninit var warning
Fix the following warning when !CONFIG_MMC:
arch/arm/mach-msm/board-trout.c: In function 'trout_init':
arch/arm/mach-msm/board-trout.c:67:6: warning: unused variable 'rc' [-Wunused-variable]
int rc;
^
Also, while we're here, rework explicit printk(KERN_CRIT..) to use
pr_crit.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org> Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Olof Johansson <olof@lixom.net>
* sh73a0 (SH-Mobile AG5) based kzm9g board
- Add FSI support
* tag 'renesas-dt2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: koelsch: dts: Add gpio-keys device
ARM: shmobile: kzm9g: add FSI support for DTS
ARM: shmobile: sh73a0: add FSI support via DTSI
Olof Johansson [Fri, 27 Dec 2013 21:09:58 +0000 (13:09 -0800)]
Merge tag 'tegra-for-3.14-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
From Stephen Warren:
ARM: tegra: second set of device tree changes
This branch contains changes to Tegra's device tree that came in after
I sent the previous pull-request/tag tegra-for-3.14-dt. Changes are:
* Set up aliases for RTCs, so that the correct RTC is chosen to
initialize the system date/time.
* Venice2 pinctrl and regulator configuration.
* Built-in panel enablement for Harmony, Cardhu, Dalmore.
* HDMI enablement for Dalmore.
* USB2 port enablement for Beaver.
* Keyboard and power key enablement for Venice2.
* tag 'tegra-for-3.14-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Enable power key on Venice2
ARM: tegra: Enable Venice2 keyboard
ARM: tegra: enable USB2 on Tegra30 Beaver
ARM: tegra: modify Tegra30 USB2 default phy_type to UTMI
ARM: tegra: Enable HDMI support on Dalmore
ARM: tegra: Enable DSI support on Dalmore
ARM: tegra: Add Tegra114 gr3d support
ARM: tegra: Add Tegra114 gr2d support
ARM: tegra: Add Tegra114 DSI support
ARM: tegra: Add host1x, DC and HDMI to Tegra114 device tree
ARM: tegra: Add MIPI calibration DT entries for Tegra114
ARM: tegra: Enable LVDS on Cardhu
ARM: tegra: Enable LVDS on Harmony
ARM: tegra: set up /aliases for RTCs on Venice2
ARM: tegra: add ams AS3722 device to Venice2 DT
ARM: tegra: fix missing pincontrol configuration for Venice2
ARM: tegra: set up /aliases entries for RTCs
Olof Johansson [Thu, 26 Dec 2013 19:03:50 +0000 (11:03 -0800)]
Merge tag 'tegra-for-3.14-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
From Stephen Warren:
ARM: tegra: device tree changes
This branch contains all the changes to Tegra's device tree. The
highlights are:
* Many patches for Tegra124 SoC support, and the Venice2 board which
uses that SoC.
* Conversion to use more headers providing named constants for pinctrl
and key codes, which improves readability.
* A few cleanups.
This branch is based on tag tegra-for-3.14-dmas-resets-rework in order
to avoid conflicts with the DT changes required to use the common
bindings for DMAs and resets.
* tag 'tegra-for-3.14-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (24 commits)
ARM: tegra: Add SPI controller nodes for Tegra124
ARM: tegra: Fix misconfiguration of pin PH2 on Venice2
ARM: tegra: fix pinctrl misconfiguration on Venice2
ARM: tegra: add default pinctrl nodes for Venice2
ARM: tegra: correct Colibri T20 regulator settings
ARM: tegra: convert dts files of Tegra30 platforms to use pinctrl defines
ARM: tegra: convert dts files of Tegra20 platforms to use pinctrl defines
ARM: tegra: convert dts files of Tegra114 platforms to use pinctrl defines
ARM: tegra: Add header file for pinctrl constants
ARM: tegra: convert device tree files to use key defines
ARM: tegra: Enable PWM on Venice2
ARM: tegra: Add Tegra124 PWM support
ARM: tegra: add sound card to Venice2 DT
ARM: tegra: add audio-related device to Tegra124 DT
ARM: tegra: enable I2C controllers on Venice2
ARM: tegra: add I2C controllers to Tegra124 DT
ARM: tegra: add MMC controllers to Tegra124 DT
ARM: tegra: add Tegra124 pinmux node to DT
ARM: tegra: add APB DMA controller to Tegra124 DT
ARM: tegra: add reset properties to Tegra124 DTs
...
This patch adds DT board setup for the LaCie NAS LaPlug.
Chipset list:
- CPU MARVELL 88FR131 800Mhz
- SDRAM memory: 128MB DDR2-800 400Mhz
- 1 Ethernet Gigabit port (PHY MARVELL 88E1318)
- 1 Mini PCI-Express port
- 1 NAND 512 MB
- 1 push button
- 2 LEDs (red and blue)
- 4 USB Ports
Signed-off-by: Maxime Hadjinlian <maxime.hadjinlian@gmail.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This file is mainly a copy of kirkwood-6281.dtsi.
The pinctrl seems to be the same.
These platforms differs only with their CPU, memory capabilities and the
number of GPIO available (36 on 6192, 50 on 6281).
Signed-off-by: Maxime Hadjinlian <maxime.hadjinlian@gmail.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Mon, 23 Dec 2013 08:48:10 +0000 (09:48 +0100)]
ARM: mvebu: fix register length for Armada XP PMSU
The per-CPU PMSU registers documented in the datasheet start at
0x22100 and the last register for CPU3 is at 0x22428. However, the DT
informations use <0x22100 0x430>, which makes the region end at
0x22530 and not 0x22430.
Moreover, looking at the datasheet, we can see that the registers for
CPU0 start at 0x22100, for CPU1 at 0x22200, for CPU2 at 0x22300 and
for CPU3 at 0x22400. It seems clear that 0x100 bytes of registers have
been used per CPU.
Therefore, this commit reduces the length of the PMSU per-CPU register
area from the incorrect 0x430 bytes to a more logical 0x400 bytes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Olof Johansson [Tue, 24 Dec 2013 02:54:04 +0000 (18:54 -0800)]
Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
From Kukjin Kim:
Samsung DT 2nd updates for v3.14
- add DMA controller, SPI, and TMU DT nodes for exynos5420
- add PWM DT nodes for exynos5250 and exynos5420
- drop interrupt controller properties from MCT nodes
because MCT is not an interrupt controller
- move MCT nodes to exynos4x12 from board because it is
a per-processor interrupt and same 4212 and 4412
- use one cell for MCT interrupt map for exynos4 SoCs
- update Exynos MCT DT bindings accordingly
- fix missing spaces after labels for exynos
- fix mmc status property for exynos5250-snow
- add MCLK for codec for exynos5250-smdk5250
- disable SPI and I2C by default for exynos5250 SoC
and enable into requiring some boards
- rename cros5250-common to exynos5250-cros-common
* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (27 commits)
ARM: dts: Rename Exynos5250 ChromeOS common file to have exynos prefix
ARM: dts: Disable I2C controllers by default on Exynos5250
ARM: dts: Leave Exynos5250 SPI controller disabled by default
ARM: dts: Add CODEC MCLK for SMDK5250
ARM: dts: Add device nodes for TMU blocks for exynos5420
ARM: dts: Fix status property of mmc nodes for snow board
ARM: dts: Fix missing spaces after labels for exynos
ARM: dts: Simplify MCT interrupt map for exynos4 SoCs
ARM: dts: Move MCT node to exynos4x12.dtsi
ARM: dts: Drop interrupt controller properties from MCT nodes for exynos4 SoCs
Documentation: devicetree: Update Exynos MCT bindings description
ARM: dts: add pwm DT nodes to Exynos5250 and Exynos5420
ARM: dts: Add SPI nodes to the exynos5420 device tree file
ARM: dts: Add DMA controller node info on Exynos5420
ARM: dts: Use MSHC controller for eMMC memory for exynos4412-trats2
ARM: dts: Fix definition of MSHC device tree nodes for exynos4x12
ARM: dts: add clock provider for mshc node for Exynos4412 SOC
clk: samsung: exynos4: Fix definition of div_mmc_pre4 divider
ARM: dts: Fix exynos5250-snow's search key to be L_META
ARM: dts: Add the missing "\" key in non-US keyboards for exynos5250-snow
...
Olof Johansson [Sun, 22 Dec 2013 22:21:06 +0000 (14:21 -0800)]
Merge tag 'at91-dt2' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre:
Second DT pull-request for 3.14
- now that PWM driver is on its way to mainline,
we can integrate the DT entries
- As an example, use PWM for at91sam9m10g45ek leds
- Addition of clock specification for newly introduced
crypto DT entries
* tag 'at91-dt2' of git://github.com/at91linux/linux-at91:
ARM: at91/dt: add clk properties to sama5d3 TDES device node
ARM: at91/dt: add clk properties to sama5d3 AES device node
ARM: at91/dt: add clk properties to sama5d3 SHA device node
ARM: at91: at91sam9m10g45ek: switch to PWM leds
ARM: at91: add PWM device node
Olof Johansson [Sun, 22 Dec 2013 22:12:57 +0000 (14:12 -0800)]
Merge tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
From Kukjin Kim:
Samsung DT updates for v3.14
- Add support Octa Cores for exynos5420
: populate CPU node entries to 8 Cores
: extend mct to support 8 local interrupts
- Update dwmmc nodes for exynos5250 and exynos5420
: change status property of dwmmc nodes for exynos5250
: move dwmmc nodes from exynos5 to exynos5250 because
it's different between exynos5250 and exynos5420
: rename mmc nodes from dwmmc for exynos5 SoCs
: add dwmmc nodes for exynos5420
- Add G-Scaler nodes for exynos5420
- Add HS-i2c nodes in exynos5420
: High Speed I2C 7 channels (4 to 10)
- Update sysreg binding and node name in exynos4
- Update min voltage on exynos5250-arndale
- Move fifo-depth property from boards to exynos5250 SoC
: because the fifo-depth property is SoC specific
* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Update Samsung sysreg binding document
ARM: dts: Fix sysreg node name in exynos4.dtsi
ARM: dts: Add hs-i2c nodes to exynos5420
ARM: dts: Update min voltage for vdd_arm on Arndale
ARM: dts: populate cpu node entries to 8 cpus for exynos5420
clocksource: mct: extend mct to support 8 local interrupts for Exynos5420
ARM: dts: Add device nodes for GScaler blocks for exynos5420
ARM: dts: Add dwmmc DT nodes for exynos5420 SOC
ARM: dts: rename mmc dts node for exynos5 series
ARM: dts: Move fifo-depth property from exynos5250 board dts
ARM: dts: change status property of dwmmc nodes for exynos5250
ARM: dts: Move dwmmc nodes from exynos5.dtsi to exynos5250.dtsi
Mark Brown [Sat, 21 Dec 2013 01:09:25 +0000 (10:09 +0900)]
ARM: dts: Rename Exynos5250 ChromeOS common file to have exynos prefix
Make it easier to notice the common file for ChromeOS devices based on
the Exynos5250 by giving it the exynos5250 prefix that the boards have.
Signed-off-by: Mark Brown <broonie@linaro.org> Acked-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Mark Brown [Fri, 20 Dec 2013 23:33:23 +0000 (08:33 +0900)]
ARM: dts: Disable I2C controllers by default on Exynos5250
Ensure that unused I2C controllers are not activated, causing problems due
to inappropriate pinmuxing or similar, by marking the controllers as
disabled by default and requiring boards to explicitly enable those that
are in use.
Signed-off-by: Mark Brown <broonie@linaro.org> Acked-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Mark Brown [Fri, 20 Dec 2013 23:31:30 +0000 (08:31 +0900)]
ARM: dts: Leave Exynos5250 SPI controller disabled by default
Rather than requiring each board to explicitly disable the SPI controllers
it is not using instead require boards to enable those that they are using.
This is less work overall since normally at most one of the controllers is
in use and avoids issues caused by inappropriate pinmuxing.
Signed-off-by: Mark Brown <broonie@linaro.org> Acked-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM: dts: Fix status property of mmc nodes for snow board
Commit e908d5c5 ("ARM: dts: change status property of dwmmc nodes
for exynos5250") missed out handling the exynos5250 snow dts file.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com> Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Tomasz Figa [Wed, 18 Dec 2013 18:17:43 +0000 (03:17 +0900)]
ARM: dts: Move MCT node to exynos4x12.dtsi
For MCT block compatible with "samsung,exynos4412-mct", that uses PPI
interrupts for local timers, only one local interrupt needs to be
specified, since it is a per-processor interrupt.
This allows moving MCT node of Exynos4x12 SoCs back to common
exynos4x12.dtsi, since they have the same set of interrupts to be
specified, which was the only difference.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Tomasz Figa [Wed, 18 Dec 2013 18:17:39 +0000 (03:17 +0900)]
ARM: dts: Drop interrupt controller properties from MCT nodes for exynos4 SoCs
MCT is not an interrupt controller and so there is no point for device
tree nodes representing it to contain interrupt-controller
and #interrupt-cells properties.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates description of device tree bindings for Exynos MCT
(multicore timers). Namely:
- added note about simplified specification of local timer interrupts,
when using single per-processor interrupt for all local timers,
- changed first example that was incorrectly suggesting that global
timer interrupts are optional,
- simplified example interrupt map,
- added example showing simplified local timer interrupt specification.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Padmavathi Venna [Wed, 18 Dec 2013 17:32:41 +0000 (02:32 +0900)]
ARM: dts: Add DMA controller node info on Exynos5420
This patch adds dma controller node info on Exynos5420.
Exynos5420 has adma for audio IPs. As adma clk is dependent
on audss clk provider that will be added later.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com> Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Tomasz Figa [Fri, 20 Dec 2013 22:37:30 +0000 (07:37 +0900)]
ARM: dts: Fix definition of MSHC device tree nodes for exynos4x12
All SoCs from Exynos4x12 series contain the MSHC block, so its node can
be located in exynos4x12.dtsi. In addition, missing clock specifiers
are added, generic SoC attributes are moved from board dts files
to common dtsi file of SoC family and the node is renamed to a more
generic name to follow node naming recommendations.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Doug Anderson [Fri, 20 Dec 2013 21:08:20 +0000 (06:08 +0900)]
ARM: dts: Fix exynos5250-snow's search key to be L_META
The device tree sent upstream for exynos5250-snow encoded the search
key as CAPSLK. However in all ChromeOS kernels it is L_META. One can
certainly have long debates about which it ought to be, but I'm
proposing setting it to L_META because:
* That's how _all_ ChromeOS kernels do it and will do it.
* There is no L_META key on the board, so it's nice to have.
* For those people who really want it to be caps lock, they can use
xmodmap or somesuch.
Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Doug Anderson [Fri, 20 Dec 2013 21:08:15 +0000 (06:08 +0900)]
ARM: dts: Add the missing "\" key in non-US keyboards for exynos5250-snow
When the exynos5250 device tree was sent upstream the keyboard mapping
was missing the 2nd instance of the "\" key. There are two copies of
the "\" because it simply has a different row and column on US and
non-US keyboards.
For more details, see the previous patch in this series: (mkbp: Fix
problems with backslash).
Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Kevin Hilman [Fri, 20 Dec 2013 20:16:49 +0000 (12:16 -0800)]
Merge tag 'renesas-dt-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
From Simon Horman:
Renesas ARM based SoC DT updates for v3.14
* Global
- Use interrupt macros
- Use #include in device tree sources
- Tidyup DT node naming
* emev2 (Emma Mobile EV2) SoC
- Setup internal peripheral interrupts as level high
- Use interrupt macros in DT files
- Add clock tree description in DT
* r8a7791 (R-Car M2) SoC
- Correct GPIO resources
* r8a7791 (R-Car M2) based Koelsch board
- Configure PFC and GPO
- Use r8a7791 suffix for IRQC compat string
- Add DT reference
* r8a7790 (R-Car H2) based Lager board
- Include all 4 GiB of memory
- Use r8a7790 suffix for IRQC and MMCIF compat strings
- Enable MMCIF
- Add default PFC settings
* r8a7778 (R-Car M1) SoC
- Suffix for INTC compat string
- Add HSPI, MMCIF, SDHI and I2C suppport on DTSI
- Correct pin control device addresses
* r8a7778 (R-Car M1) based Bock-W board
- Use falling edge IRQ for LAN9221 in DT reference
- Enable I2C, HSPI0, MMCIF and SDHI
- Correct MMC pin conflict
- Remove manual PFC settings from DT reference
- Add default PFC settings
* r8a7779 (R-Car H1) SoC
- Add HSPI and SDHI support
- Suffix for INTC compat string
* r8a7779 (R-Car H1) based Marzen board
- Enable HSPI0 and SDHI in DTS
- Remove SDHI0 WP pin setting
- Use falling edge IRQ for LAN9221 in DT reference
- Add SDHI support
* r8a7740 (R-Mobile A1) SoC
- Suffix for INTC compat string
- Add FSI support via DTSI
- Use interrupt macros
* r8a7740 based Armadillo board
- Add FSI support for DTS
- Use low level IRQ for ST1231 in DT reference
* r8a73a4 (SH-Mobile APE6) SoC
- Use interrupt macros in DT files
* r8a73a4 (R-Mobile APE6) based ape6evm board
- Include all 2 GiB of memory
* r8a73a0 (SH-Mobile AG5) based kzm9d board
- Add GPIO keys and Add PCF8575 GPIO extender to DT
- Enable DSW2 with gpio-keys
- Use falling edge IRQ for LAN9221 in DT reference
* tag 'renesas-dt-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (102 commits)
ARM: shmobile: marzen: enable HSPI0 in DTS
ARM: shmobile: r8a7779: add HSPI support to DTSI
ARM: shmobile: Use r8a7779 suffix for INTC compat string
ARM: shmobile: Use r8a7778 suffix for INTC compat string
ARM: shmobile: Use r8a7740 suffix for INTC compat string
ARM: shmobile: Use sh73a0 suffix for INTC compat string
ARM: shmobile: armadillo: add FSI support for DTS
ARM: shmobile: r8a7740: add FSI support via DTSI
ARM: shmobile: emev2: Setup internal peripheral interrupts as level high
ARM: shmobile: emev2: Use interrupt macros in DT files
ARM: shmobile: Use interrupt macros in r8a73a4 and r8a7778 DT files
ARM: shmobile: Fix r8a7791 GPIO resources in DTS
ARM: shmobile: Include all 4 GiB of memory on Lager DT Ref
ARM: shmobile: Include all 4 GiB of memory on Lager
ARM: shmobile: Include all 2 GiB of memory on APE6EVM
ARM: shmobile: Include all 2 GiB of memory on APE6EVM DT Ref
ARM: shmobile: kzm9g-reference: Add GPIO keys to DT
ARM: shmobile: kzm9g-reference: Add PCF8575 GPIO extender to DT
ARM: shmobile: Koelsch DT reference GPIO LED support
ARM: shmobile: Enable DSW2 with gpio-keys on KZM9D
...
Thierry Reding [Thu, 19 Dec 2013 16:06:20 +0000 (17:06 +0100)]
ARM: tegra: Enable power key on Venice2
Contrary to the rest of the keyboard, which is connected to the ChromeOS
embedded controller, the power key is hooked up to a GPIO. Add a device
tree node to handle it.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Thierry Reding [Thu, 19 Dec 2013 16:06:19 +0000 (17:06 +0100)]
ARM: tegra: Enable Venice2 keyboard
The keyboard on Venice2 is attached to the ChromeOS embedded controller.
Add the corresponding device tree nodes and use the MATRIX_KEY define to
encode keycodes.
Signed-off-by: Rhyland Klein <rklein@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Now that support for Intersil ISL12057 RTC chip is available
upstream, let's enable it in NETGEAR ReadyNAS 2120 .dts file
so that the device stop believing it's the 70's.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that support for Intersil ISL12057 RTC chip is available
upstream, let's enable it in NETGEAR ReadyNAS 104 .dts file
so that the device stop believing it's the 70's.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that support for Intersil ISL12057 RTC chip is available
upstream, let's enable it in NETGEAR ReadyNAS 102 .dts file
so that the device stop believing it's the 70's.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Mikko Perttunen [Thu, 19 Dec 2013 15:59:33 +0000 (16:59 +0100)]
ARM: tegra: Enable HDMI support on Dalmore
Add HDMI node to the Dalmore device tree and hook up the VDD and PLL
regulators as well as the I2C adapter used for DDC and the GPIO used
for hotplug detection.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Thierry Reding [Thu, 19 Dec 2013 15:59:27 +0000 (16:59 +0100)]
ARM: tegra: Add MIPI calibration DT entries for Tegra114
Add a device node for the MIPI calibration block on Tegra114. There is
no need to disable it by default because it only enables the clock while
performing calibration and therefore shouldn't be consuming any power
when unused.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[swarren, add unit address to new DT node name] Signed-off-by: Stephen Warren <swarren@nvidia.com>
Kevin Hilman [Thu, 19 Dec 2013 15:24:35 +0000 (07:24 -0800)]
Merge tag 'nomadik-dt-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
From Linus Walleij:
Some Nomadik Device Tree updates for the v3.14 cycle:
- Drop 0x prefixes
- Get rid of explicit GPIO management
* tag 'nomadik-dt-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: get rid of explicit ethernet GPIO management
ARM: nomadik: Remove '0x's from nomadik stn8815 DTS file
Tomasz Figa [Wed, 18 Dec 2013 17:45:47 +0000 (02:45 +0900)]
ARM: S3C64XX: Correct card detect type for HSMMC1 for MINI6410
According to board schematics, for HSMMC1 a GPIO line is used to detect
card presence, while currently it is being configured for internal card
detect line, which is multiplexed with card detect line of HSMMC0 and
thus breaking it.
This patch adds proper sdhci platform data setting card detect type to
external GPIO and fixing operation of HSMMC0.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Laxman Dewangan [Mon, 2 Dec 2013 13:09:57 +0000 (18:39 +0530)]
ARM: tegra: convert device tree files to use key defines
Use key code macros for all key code refernced for keys.
For tegra20-seaboard.dts and tegra20-harmony.dts:
The key comment for key (16th row and 1st column) is KEY_KPSLASH but
code is 0x004e which is the key code for KEY_KPPLUS. As there other
key exist with KY_KPPLUS, I am assuming key code is wrong and comment
is fine. With this assumption, I am keeping the key code as KEY_KPSLASH.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Wed, 4 Dec 2013 00:26:12 +0000 (17:26 -0700)]
ARM: tegra: add sound card to Venice2 DT
Venice2 uses the MAX98090 audio CODEC, and supports built-in speakers,
and a combo headphones/microphone jack. Add a top-level sound card node
to represent this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Wed, 4 Dec 2013 22:05:51 +0000 (15:05 -0700)]
ARM: tegra: add audio-related device to Tegra124 DT
Tegra124 contains a similar set of audio devices to previous Tegra chips.
Specifically, there is an AHUB device which contains DMA FIFOs and audio
routing, and which hosts various audio-related components such as I2S
controllers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Tue, 3 Dec 2013 23:44:35 +0000 (16:44 -0700)]
ARM: tegra: enable I2C controllers on Venice2
Enable all the I2C controllers that are wired up on Venice2. I don't
know the correct I2C bus clock rates, so set them all to a conservative
100KHz for now.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Thu, 31 Oct 2013 23:23:05 +0000 (17:23 -0600)]
ARM: tegra: add MMC controllers to Tegra124 DT
Tegra124 has 4 MMC controllers just like previous versions of the SoC.
Note that there are some non-backwards-compatible HW differences, and
hence a new DT compatible value must be used to describe the HW.
Also enable the relevant controllers in the Venice2 board DT.
Stephen Warren [Fri, 15 Nov 2013 19:22:53 +0000 (12:22 -0700)]
ARM: tegra: add APB DMA controller to Tegra124 DT
Instantiate the APB DMA controller in the Tegra124 DT, and add all
DMA-related properties to other DT nodes that rely on (reference) the
DMA controller's node.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com>
Stephen Warren [Thu, 7 Nov 2013 19:20:57 +0000 (12:20 -0700)]
ARM: tegra: add reset properties to Tegra124 DTs
The DT bindings now require module resets to be specified. The earlier
patches which added these nodes were originally written before that
requirement.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com>
Stephen Warren [Tue, 26 Nov 2013 21:43:45 +0000 (14:43 -0700)]
ARM: tegra: fix node sort order
For Tegra DT files, I've been attempting to keep the nodes sorted in
the order:
1) Nodes with reg, in order of reg.
2) Nodes without reg, alphabetically.
This patch fixes a few escapees that I missed:-(
The diffs look larger than they really are, because sometimes when one
node was moved up or down, diff chose to represent this as many other
nodes being moved the other way!
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Tue, 26 Nov 2013 00:53:16 +0000 (17:53 -0700)]
ARM: tegra: add missing unit addresses to DT
DT node names should include a unit address iff the node has a reg
property. For Tegra DTs at least, we were previously applying a different
rule, namely that node names only needed to include a unit address if it
was required to make the node name unique. Consequently, many unit
addresses are missing. Add them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
projects / linux-beck.git / log