Oliver Hartkopp [Thu, 29 Sep 2011 19:33:47 +0000 (15:33 -0400)]
can bcm: fix incomplete tx_setup fix
The commit aabdcb0b553b9c9547b1a506b34d55a764745870 ("can bcm: fix tx_setup
off-by-one errors") fixed only a part of the original problem reported by
Andre Naujoks. It turned out that the original code needed to be re-ordered
to reduce complexity and to finally fix the reported frame counting issues.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
In the rds_iw_mr_pool struct the free_pinned field keeps track of
memory pinned by free MRs. While this field is incremented properly
upon allocation, it is never decremented upon unmapping. This would
cause the rds_rdma module to crash the kernel upon unloading, by
triggering the BUG_ON in the rds_iw_destroy_mr_pool function.
This change keeps track of the MRs that become unpinned, so that
free_pinned can be decremented appropriately.
Signed-off-by: Jonathan Lallinger <jonathan@ogc.us> Signed-off-by: Steve Wise <swise@ogc.us> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Riesch [Thu, 29 Sep 2011 04:06:26 +0000 (04:06 +0000)]
usbnet: add timestamping support
In order to make USB-to-Ethernet-adapters (depending on usbnet) support
timestamping, the "skb_defer_rx_timestamp" and "skb_tx_timestamp" function
calls are added.
Signed-off-by: Michael Riesch <michael@riesch.at> Signed-off-by: David S. Miller <davem@davemloft.net>
powerpc: Don't try OPAL takeover on old 970 blades
The firmware on old 970 blades supports some kind of takeover called
"TNK takeover" which will crash if we try to probe for OPAL takeover,
so don't do it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current L1 cache read event code 0x80082 only counts for thread 0. The
event code 0x280030 should be used to count events on thread 0 and 1. The
patch fixes the event code for the L1 cache read.
The current L1 cache write event code 0x80086 only counts for thread 0. The
event code 0x180032 should be used to count events on thread 0 and 1. The
patch fixes the event code for the L1 cache write.
FYI, the documentation lists three event codes for the L1 cache read event
and three event codes for the L1 cache write event. The event description
for the event codes is as follows:
L1 cache read requests 0x80082 LSU 0 only
L1 cache read requests 0x8008A LSU 1 only
L1 cache read requests 0x80030 LSU 1 or LSU 0, counter 2 only.
L1 cache store requests 0x80086 LSU 0 only
L1 cache store requests 0x8008E LSU 1 only
L1 cache store requests 0x80032 LSU 0 or LSU 1, counter 1 only.
There can only be one request from either LSU 0 or 1 active at a time.
Signed-off-by: Carl Love <cel@us.ibm.com> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
gcc (rightfully) complains that we are accessing beyond the
end of the fpr array (we do, to access the fpscr).
The only sane thing to do (whether anything in that code can be
called remotely sane is debatable) is to special case fpscr and
handle it as a separate statement.
I initially tried to do it it by making the array access conditional
to index < PT_FPSCR and using a 3rd else leg but for some reason gcc
was unable to understand it and still spewed the warning.
So I ended up with something a tad more intricated but it seems to
build on 32-bit and on 64-bit with and without VSX.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
xmon has a longstanding bug on systems which are SMP-capable but lack
the MSR[RI] bit. In these cases, xmon invoked by IPI on secondary
CPUs will not properly keep quiet, but will print stuff, thereby
garbling the primary xmon's output. This patch fixes it, by ignoring
the RI bit if the processor does not support it.
There's already a version of this for 4xx upstream, which we'll need
to extend to other RI-lacking CPUs at some point. For now this adds
Book3e processors to the mix.
Signed-off-by: Jimi Xenidis <jimix@pobox.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Dan Carpenter [Thu, 29 Sep 2011 06:10:48 +0000 (09:10 +0300)]
sound: oss: use strlcpy() in sound_timer_init()
sound_timer.info.name is a 32 character buffer. This function only
has one caller (in sound/oss/ad1848.c) and it passes as 128 character
buffer as "name". I don't know if this is a problem in real life,
and I doubt we're going to add more OSS drivers so it's unlikely to
become an issue. But we may as well take care of it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Don Skidmore [Thu, 4 Aug 2011 02:07:48 +0000 (02:07 +0000)]
ixgbe: add ECC warning for legacy interrupts
Noticed that the legacy Interrupt handler didn't have the same
ECC warning as did the MSI. So this patch adds it.
Signed-off-by: Don Skidmore <donald.c.skidmore> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Wed, 17 Aug 2011 10:15:21 +0000 (10:15 +0000)]
ixgbe: cleanup ixgbe_setup_gpie() for X540
The X540 thermal sensor interrupt isn't a General Purpose Interrupt
so doesn't need to be enabled in ixgbe_setup_gpie(). Likewise X540 doesn't
use the SDP0 for thermal sensor so it doesn't need to be enabled for any
device other than 82599.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Sat, 20 Aug 2011 04:49:45 +0000 (04:49 +0000)]
ixgbe add thermal sensor support for x540 hardware
Add code to enable thermal sensors for the x540 hardware, as well as a
thermal interrupt check which will exit with a critical message of a
thermal overheat is detected. Intent of code allows other mac types to
be added with different configuration in the future.
Fixed in this version is the addition of setting the temp_sensor
capable flag which was previously only set for a specific mac.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John Fastabend [Tue, 23 Aug 2011 03:14:22 +0000 (03:14 +0000)]
ixgbe: update {P}FC thresholds to account for X540 and loopback
Revise high and low threshold marks wrt flow control to account
for the X540 devices and latency introduced by the loopback
switch.
Without this it was in theory possible to drop frames on a
supposedly lossless link with X540 or SR-IOV enabled.
Previously we used a magic number in a define to calculate the
threshold values. This made it difficult to sort out exactly
which latencies were or were not being accounted for. Here
I was overly explicit and tried to used #define names that would
be recognizable after reading the IEEE 802.1Qbb specification.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Vasu Dev [Thu, 18 Aug 2011 06:20:07 +0000 (06:20 +0000)]
ixgbe: disable LLI for FCoE
Disable LLI for FCoE since regular interrupt
and their moderation rate works slightly better
for FCoE also.
Signed-off-by: Vasu Dev <vasu.dev@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to help cleanup the interrupt throttle rate logic by
storing the interrupt throttle rate as a value in microseconds instead of
interrupts per second. The advantage to this approach is that the value
can now be stored in an 16 bit field and doesn't require as much math to
flip the value back and forth since the hardware already used microseconds
when setting the rate.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dean Nelson [Fri, 16 Sep 2011 16:52:54 +0000 (16:52 +0000)]
e1000: don't enable dma receives until after dma address has been setup
Doing an 'ifconfig ethN down' followed by an 'ifconfig ethN up' on a qemu-kvm
guest system configured with two e1000 NICs can result in an 'unable to handle
kernel paging request at 0000000100000000' or 'bad page map in process ...' or
something similar.
These result from a 4096-byte page being corrupted with the following two-word
pattern (16-bytes) repeated throughout the entire page:
0x0000000000000000
0x0000000100000000
There can be other bits set as well. What is a constant is that the 2nd word
has the 32nd bit set. So one could see:
Which came from from a process' page table I dumped out when the marked line
was seen as bad by print_bad_pte().
The repeating pattern represents the e1000's two-word receive descriptor:
struct e1000_rx_desc {
__le64 buffer_addr; /* Address of the descriptor's data buffer */
__le16 length; /* Length of data DMAed into data buffer */
__le16 csum; /* Packet checksum */
u8 status; /* Descriptor status */
u8 errors; /* Descriptor Errors */
__le16 special;
};
And the 32nd bit of the 2nd word maps to the 'u8 status' member, and
corresponds to E1000_RXD_STAT_DD which indicates the descriptor is done.
The corruption appears to result from the following...
. An 'ifconfig ethN down' gets us into e1000_close(), which through a number
of subfunctions results in:
1. E1000_RCTL_EN being cleared in RCTL register. [e1000_down()]
2. dma_free_coherent() being called. [e1000_free_rx_resources()]
. An 'ifconfig ethN up' gets us into e1000_open(), which through a number of
subfunctions results in:
1. dma_alloc_coherent() being called. [e1000_setup_rx_resources()]
2. E1000_RCTL_EN being set in RCTL register. [e1000_setup_rctl()]
3. E1000_RCTL_EN being cleared in RCTL register. [e1000_configure_rx()]
4. RDLEN, RDBAH and RDBAL registers being set to reflect the dma page
allocated in step 1. [e1000_configure_rx()]
5. E1000_RCTL_EN being set in RCTL register. [e1000_configure_rx()]
During the 'ifconfig ethN up' there is a window opened, starting in step 2
where the receives are enabled up until they are disabled in step 3, in which
the address of the receive descriptor dma page known by the NIC is still the
previous one which was freed during the 'ifconfig ethN down'. If this memory
has been reallocated for some other use and the NIC feels so inclined, it will
write to that former dma page with predictably unpleasant results.
I realize that in the guest, we're dealing with an e1000 NIC that is software
emulated by qemu-kvm. The problem doesn't appear to occur on bare-metal. Andy
suspects that this is because in the emulator link-up is essentially instant
and traffic can start flowing immediately. Whereas on bare-metal, link-up
usually seems to take at least a few milliseconds. And this might be enough
to prevent traffic from flowing into the device inside the window where
E1000_RCTL_EN is set.
So perhaps a modification needs to be made to the qemu-kvm e1000 NIC emulator
to delay the link-up. But in defense of the emulator, it seems like a bad idea
to enable dma operations before the address of the memory to be involved has
been made known.
The following patch no longer enables receives in e1000_setup_rctl() but leaves
them however they were. It only enables receives in e1000_configure_rx(), and
only after the dma address has been made known to the hardware.
There are two places where e1000_setup_rctl() gets called. The one in
e1000_configure() is followed immediately by a call to e1000_configure_rx(), so
there's really no change functionally (except for the removal of the problem
window. The other is in __e1000_shutdown() and is not followed by a call to
e1000_configure_rx(), so there is a change functionally. But consider...
. An 'ifconfig ethN down' (just as described above).
. A 'suspend' of the system, which (I'm assuming) will find its way into
e1000_suspend() which calls __e1000_shutdown() resulting in:
1. E1000_RCTL_EN being set in RCTL register. [e1000_setup_rctl()]
And again we've re-opened the problem window for some unknown amount of time.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Dean Nelson <dnelson@redhat.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brian King [Wed, 28 Sep 2011 05:33:43 +0000 (05:33 +0000)]
ibmveth: Fix oops on request_irq failure
If request_irq fails, the ibmveth driver will overwrite
the rc and end up returning a successful rc on its open
function, resulting in an oops later when a packet gets
sent and buffers are not allocated due to the failed open.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Fri, 23 Sep 2011 08:23:47 +0000 (08:23 +0000)]
can bcm: fix tx_setup off-by-one errors
This patch fixes two off-by-one errors that canceled each other out.
Checking for the same condition two times in bcm_tx_timeout_tsklet() reduced
the count of frames to be sent by one. This did not show up the first time
tx_setup is invoked as an additional frame is sent due to TX_ANNONCE.
Invoking a second tx_setup on the same item led to a reduced (by 1) number of
sent frames.
Reported-by: Andre Naujoks <nautsch@gmail.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Ian Campbell [Wed, 21 Sep 2011 22:08:26 +0000 (22:08 +0000)]
MAINTAINERS: tehuti: Alexander Indenbaum's address bounces
I got:
Generating server: Tehuti.onmicrosoft.com
baum@tehutinetworks.net
#< #5.1.1 smtp;550 5.1.1 RESOLVER.ADR.RecipNotFound; not found> #SMTP#
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: Alexander Indenbaum <baum@tehutinetworks.net> Cc: Andy Gospodarek <andy@greyhouse.net> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Tue, 20 Sep 2011 01:25:42 +0000 (01:25 +0000)]
dp83640: reduce driver noise
The driver has two warning messages that might be triggered
by normal use cases. When they appear, the messages give the
impression of a never ending series of errors.
This commit changes them to debug messages instead.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at> Signed-off-by: David S. Miller <davem@davemloft.net>