Yaniv Rosner [Sun, 30 Jan 2011 04:15:07 +0000 (04:15 +0000)]
bnx2x: Fix potential link loss in multi-function mode
All functions on a port should be set to take the MDC/MDIO lock to avoid contention on the bus
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Sun, 30 Jan 2011 04:15:00 +0000 (04:15 +0000)]
bnx2x: Fix port swap for BCM8073
Fix link on BCM57712 + BCM8073 when port swap is enabled. Common PHY reset was done on the wrong port.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Sun, 30 Jan 2011 04:14:55 +0000 (04:14 +0000)]
bnx2x: Fix LED blink rate on BCM84823
Fix blink rate of activity LED of the BCM84823 on 10G link
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Sun, 30 Jan 2011 04:14:48 +0000 (04:14 +0000)]
bnx2x: Remove setting XAUI low-power for BCM8073
A rare link issue with the BCM8073 PHY may occur due to setting XAUI low power mode, while the PHY microcode already does that.
The fix is not to set set XAUI low power mode for this PHY.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sven Eckelmann [Fri, 28 Jan 2011 17:34:07 +0000 (18:34 +0100)]
batman-adv: Make vis info stack traversal threadsafe
The batman-adv vis server has to a stack which stores all information
about packets which should be send later. This stack is protected
with a spinlock that is used to prevent concurrent write access to it.
The send_vis_packets function has to take all elements from the stack
and send them to other hosts over the primary interface. The send will
be initiated without the lock which protects the stack.
The implementation using list_for_each_entry_safe has the problem that
it stores the next element as "safe ptr" to allow the deletion of the
current element in the list. The list may be modified during the
unlock/lock pair in the loop body which may make the safe pointer
not pointing to correct next element.
It is safer to remove and use the first element from the stack until no
elements are available. This does not need reduntant information which
would have to be validated each time the lock was removed.
Reported-by: Russell Senior <russell@personaltelco.net> Signed-off-by: Sven Eckelmann <sven@narfation.org>
Sven Eckelmann [Fri, 28 Jan 2011 17:34:06 +0000 (18:34 +0100)]
batman-adv: Remove vis info element in free_info
The free_info function will be called when no reference to the info
object exists anymore. It must be ensured that the allocated memory
gets freed and not only the elements which are managed by the info
object.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Sven Eckelmann [Fri, 28 Jan 2011 17:34:05 +0000 (18:34 +0100)]
batman-adv: Remove vis info on hashing errors
A newly created vis info object must be removed when it couldn't be
added to the hash. The old_info which has to be replaced was already
removed and isn't related to the hash anymore.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
net: Add compat ioctl support for the ipv4 multicast ioctl SIOCGETSGCNT
SIOCGETSGCNT is not a unique ioctl value as it it maps tio SIOCPROTOPRIVATE +1,
which unfortunately means the existing infrastructure for compat networking
ioctls is insufficient. A trivial compact ioctl implementation would conflict
with:
To make this work I have updated the compat_ioctl decode path to mirror the
the normal ioctl decode path. I have added an ipv4 inet_compat_ioctl function
so that I can have ipv4 specific compat ioctls. I have added a compat_ioctl
function into struct proto so I can break out ioctls by which kind of ip socket
I am using. I have added a compat_raw_ioctl function because SIOCGETSGCNT only
works on raw sockets. I have added a ipmr_compat_ioctl that mirrors the normal
ipmr_ioctl.
This was necessary because unfortunately the struct layout for the SIOCGETSGCNT
has unsigned longs in it so changes between 32bit and 64bit kernels.
This change was sufficient to run a 32bit ip multicast routing daemon on a
64bit kernel.
Reported-by: Bill Fenner <fenner@aristanetworks.com> Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This bug was introduced in:
commit 81adee47dfb608df3ad0b91d230fb3cef75f0060
Author: Eric W. Biederman <ebiederm@aristanetworks.com>
Date: Sun Nov 8 00:53:51 2009 -0800
net: Support specifying the network namespace upon device creation.
There is no good reason to not support userspace specifying the
network namespace during device creation, and it makes it easier
to create a network device and pass it to a child network namespace
with a well known name.
We have to be careful to ensure that the target network namespace
for the new device exists through the life of the call. To keep
that logic clear I have factored out the network namespace grabbing
logic into rtnl_link_get_net.
In addtion we need to continue to pass the source network namespace
to the rtnl_link_ops.newlink method so that we can find the base
device source network namespace.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Where apparently I forgot to add error handling to the path where we create
a new network device in a new network namespace, and pass in an invalid pid.
Cc: stable@kernel.org Reported-by: Ed Swierk <eswierk@bigswitch.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 27 Jan 2011 22:55:22 +0000 (14:55 -0800)]
ipv6: Remove route peer binding assertions.
They are bogus. The basic idea is that I wanted to make sure
that prefixed routes never bind to peers.
The test I used was whether RTF_CACHE was set.
But first of all, the RTF_CACHE flag is set at different spots
depending upon which ip6_rt_copy() caller you're talking about.
I've validated all of the code paths, and even in the future
where we bind peers more aggressively (for route metric COW'ing)
we never bind to prefix'd routes, only fully specified ones.
This even applies when addrconf or icmp6 routes are allocated.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 25 Jan 2011 23:18:38 +0000 (23:18 +0000)]
net: add kmemcheck annotation in __alloc_skb()
pskb_expand_head() triggers a kmemcheck warning when copy of
skb_shared_info is done in pskb_expand_head()
This is because destructor_arg field is not necessarily initialized at
this point. Add kmemcheck_annotate_variable() call in __alloc_skb() to
instruct kmemcheck this is a normal situation.
Resolves bugzilla.kernel.org 27212
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=27212 Reported-by: Christian Casteyde <casteyde.christian@free.fr> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Kurt Van Dijck [Wed, 26 Jan 2011 04:55:24 +0000 (04:55 +0000)]
net: fix validate_link_af in rtnetlink core
I'm testing an API that uses IFLA_AF_SPEC attribute.
In the rtnetlink core , the set_link_af() member
of the rtnl_af_ops struct receives the nested attribute
(as I expected), but the validate_link_af() member
receives the parent attribute.
IMO, this patch fixes this.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Signed-off-by: David S. Miller <davem@davemloft.net>
Patch fixes: "DMA-API: device driver tries to free an invalid DMA
memory address" warning reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=639824
Reported-by: Frantisek Hanzlik <franta@hanzlici.cz> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ian Campbell [Thu, 27 Jan 2011 04:14:03 +0000 (04:14 +0000)]
xen: netfront: handle incoming GSO SKBs which are not CHECKSUM_PARTIAL
The Linux network stack expects all GSO SKBs to have ip_summed ==
CHECKSUM_PARTIAL (which implies that the frame contains a partial
checksum) and the Xen network ring protocol similarly expects an SKB
which has GSO set to also have NETRX_csum_blank (which also implies a
partial checksum).
However there have been cases of buggy guests which mark a frame as
GSO but do not set csum_blank. If we detect that we a receiving such a
frame (which manifests as ip_summed != PARTIAL && skb_is_gso) then
force the SKB to partial and recalculate the checksum, since we cannot
rely on the peer having done so if they have not set csum_blank.
Add an ethtool stat to track occurances of this event.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: David Miller <davem@davemloft.net> Cc: xen-devel@lists.xensource.com Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 26 Jan 2011 00:04:18 +0000 (00:04 +0000)]
econet: remove compiler warnings
net/econet/af_econet.c: In function ‘econet_sendmsg’:
net/econet/af_econet.c:494: warning: label ‘error’ defined but not used
net/econet/af_econet.c:268: warning: unused variable ‘sk’
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Phil Blundell <philb@gnu.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Tue, 25 Jan 2011 22:14:50 +0000 (22:14 +0000)]
cnic: Fix big endian bug
The chip's page tables did not set up properly on big endian machines,
causing EEH errors on PPC machines.
Reported-by: Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 26 Jan 2011 21:13:10 +0000 (13:13 -0800)]
tg3: Use new VLAN code
This patch pivots the tg3 driver to the new VLAN infrastructure.
All references to vlgrp have been removed. The driver still attempts to
disable VLAN tag stripping if CONFIG_VLAN_8021Q or
CONFIG_VLAN_8021Q_MODULE is not defined.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Lüssing [Tue, 25 Jan 2011 21:56:16 +0000 (21:56 +0000)]
batman-adv: Fix kernel panic when fetching vis data on a vis server
The hash_iterate removal introduced a bug leading to a kernel panic when
fetching the vis data on a vis server. That commit forgot to rename one
variable name, which this commit fixes now.
Reported-by: Russell Senior <russell@personaltelco.net> Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: Sven Eckelmann <sven@narfation.org>
Jerry Chu [Tue, 25 Jan 2011 21:46:30 +0000 (13:46 -0800)]
TCP: fix a bug that triggers large number of TCP RST by mistake
This patch fixes a bug that causes TCP RST packets to be generated
on otherwise correctly behaved applications, e.g., no unread data
on close,..., etc. To trigger the bug, at least two conditions must
be met:
1. The FIN flag is set on the last data packet, i.e., it's not on a
separate, FIN only packet.
2. The size of the last data chunk on the receive side matches
exactly with the size of buffer posted by the receiver, and the
receiver closes the socket without any further read attempt.
This bug was first noticed on our netperf based testbed for our IW10
proposal to IETF where a large number of RST packets were observed.
netperf's read side code meets the condition 2 above 100%.
Before the fix, tcp_data_queue() will queue the last skb that meets
condition 1 to sk_receive_queue even though it has fully copied out
(skb_copy_datagram_iovec()) the data. Then if condition 2 is also met,
tcp_recvmsg() often returns all the copied out data successfully
without actually consuming the skb, due to a check
"if ((chunk = len - tp->ucopy.len) != 0) {"
and
"len -= chunk;"
after tcp_prequeue_process() that causes "len" to become 0 and an
early exit from the big while loop.
I don't see any reason not to free the skb whose data have been fully
consumed in tcp_data_queue(), regardless of the FIN flag. We won't
get there if MSG_PEEK is on. Am I missing some arcane cases related
to urgent data?
Signed-off-by: H.K. Jerry Chu <hkchu@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reinette Chatre [Tue, 25 Jan 2011 16:38:06 +0000 (08:38 -0800)]
MAINTAINERS: remove Reinette Chatre as iwlwifi maintainer
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 24 Jan 2011 18:28:49 +0000 (19:28 +0100)]
mac80211: fix a crash in ieee80211_beacon_get_tim on change_interface
Some drivers (e.g. ath9k) do not always disable beacons when they're
supposed to. When an interface is changed using the change_interface op,
the mode specific sdata part is in an undefined state and trying to
get a beacon at this point can produce weird crashes.
To fix this, add a check for ieee80211_sdata_running before using
anything from the sdata.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
because the core semantic change to ipv6 address handling on ifdown
has broken some things, in particular "disable_ipv6" sysctl handling.
Stephen has made several attempts to get things back in working order,
but nothing has restored disable_ipv6 fully yet.
Reported-by: Eric W. Biederman <ebiederm@xmission.com> Tested-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
textsearch: doc - fix spelling in lib/textsearch.c.
Found the following spelling errors while reading the textsearch code:
"facitilies" -> "facilities"
"continously" -> "continuously"
"arbitary" -> "arbitrary"
"patern" -> "pattern"
"occurences" -> "occurrences"
I'll try to push this patch through DaveM, given the only users
of textsearch is in the net/ tree (nf_conntrack_amanda.c, xt_string.c
and em_text.c)
Signed-off-by: Jesper Sander <sander.contrib@gmail.com> Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Juhl [Sun, 23 Jan 2011 12:19:55 +0000 (12:19 +0000)]
USB NET KL5KUSB101: Fix mem leak in error path of kaweth_download_firmware()
We will leak the storage allocated by request_firmware() if the size of
the firmware is greater than KAWETH_FIRMWARE_BUF_SIZE.
This removes the leak by calling release_firmware() before we return
-ENOSPC.
Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 24 Jan 2011 12:59:02 +0000 (12:59 +0000)]
bnx2: Always set ETH_FLAG_TXVLAN
TSO does not work if the VLAN tag is in the packet (non-accelerated).
We may be able to remove this restriction in future firmware.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Fri, 21 Jan 2011 16:35:18 +0000 (16:35 +0000)]
dcbnl: make get_app handling symmetric for IEEE and CEE DCBx
The IEEE get/set app handlers use generic routines and do not
require the net_device to implement the dcbnl_ops routines. This
patch makes it symmetric so user space and drivers do not have
to handle the CEE version and IEEE DCBx versions differently.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 24 Jan 2011 22:41:20 +0000 (14:41 -0800)]
tcp: fix bug in listening_get_next()
commit a8b690f98baf9fb19 (tcp: Fix slowness in read /proc/net/tcp)
introduced a bug in handling of SYN_RECV sockets.
st->offset represents number of sockets found since beginning of
listening_hash[st->bucket].
We should not reset st->offset when iterating through
syn_table[st->sbucket], or else if more than ~25 sockets (if
PAGE_SIZE=4096) are in SYN_RECV state, we exit from listening_get_next()
with a too small st->offset
Next time we enter tcp_seek_last_pos(), we are not able to seek past
already found sockets.
Reported-by: PK <runningdoglackey@yahoo.com> CC: Tom Herbert <therbert@google.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Mon, 24 Jan 2011 12:08:48 +0000 (12:08 +0000)]
GRO: fix merging a paged skb after non-paged skbs
Suppose that several linear skbs of the same flow were received by GRO. They
were thus merged into one skb with a frag_list. Then a new skb of the same flow
arrives, but it is a paged skb with data starting in its frags[].
Before adding the skb to the frag_list skb_gro_receive() will of course adjust
the skb to throw away the headers. It correctly modifies the page_offset and
size of the frag, but it leaves incorrect information in the skb:
->data_len is not decreased at all.
->len is decreased only by headlen, as if no change were done to the frag.
Later in a receiving process this causes skb_copy_datagram_iovec() to return
-EFAULT and this is seen in userspace as the result of the recv() syscall.
In practice the bug can be reproduced with the sfc driver. By default the
driver uses an adaptive scheme when it switches between using
napi_gro_receive() (with skbs) and napi_gro_frags() (with pages). The bug is
reproduced when under rx load with enough successful GRO merging the driver
decides to switch from the former to the latter.
Manual control is also possible, so reproducing this is easy with netcat:
- on machine1 (with sfc): nc -l 12345 > /dev/null
- on machine2: nc machine1 12345 < /dev/zero
- on machine1:
echo 1 > /sys/module/sfc/parameters/rx_alloc_method # use skbs
echo 2 > /sys/module/sfc/parameters/rx_alloc_method # use pages
- See that nc has quit suddenly.
[v2: Modified by Eric Dumazet to avoid advancing skb->data past the end
and to use a temporary variable.]
Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 24 Jan 2011 21:16:16 +0000 (13:16 -0800)]
net: arp_ioctl() must hold RTNL
Commit 941666c2e3e0 "net: RCU conversion of dev_getbyhwaddr() and
arp_ioctl()" introduced a regression, reported by Jamie Heilman.
"arp -Ds 192.168.2.41 eth0 pub" triggered the ASSERT_RTNL() assert
in pneigh_lookup()
Removing RTNL requirement from arp_ioctl() was a mistake, just revert
that part.
Reported-by: Jamie Heilman <jamie@audible.transient.net> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shaohua Li [Mon, 24 Jan 2011 08:00:01 +0000 (08:00 +0000)]
fix a shutdown regression in intel_idle
Fix a shutdown regression caused by 2a2d31c8dc6f ("intel_idle: open
broadcast clock event"). The clockevent framework can automatically
shutdown broadcast timers for hotremove CPUs. And we get a shutdown
regression when we shutdown broadcast timer for hot remove CPU, so just
delete some code.
Also fix some section mismatch.
Reported-by: Ari Savolainen <ari.m.savolainen@gmail.com> Signed-off-by: Shaohua Li <shaohua.li@intel.com> Tested-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 24 Jan 2011 19:29:49 +0000 (05:29 +1000)]
Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap: DMA: clear interrupt status correctly
OMAP3: Devkit8000: Fix tps65930 pullup/pulldown configuration
arm: omap3: cm-t3517: minor comment fix
arm: omap3: cm-t3517: rtc fix
omap1: Fix sched_clock implementation when both MPU timer and 32K timer are used
omap1: Fix booting for 15xx and 730 with omap1_defconfig
omap1: Fix sched_clock for the MPU timer
OMAP: PRCM: remove duplicated headers
OMAP4: clockdomain: bypass unimplemented wake-up dependency functions on OMAP4
OMAP: counter_32k: init clocksource as part of machine timer init
Linus Torvalds [Mon, 24 Jan 2011 19:26:47 +0000 (05:26 +1000)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Fix time function double declaration with glibc
perf tools: Fix build by checking if extra warnings are supported
perf tools: Fix build when using gcc 3.4.6
perf tools: Add missing header, fixes build
perf tools: Fix 64 bit integer format strings
perf test: Fix build on older glibcs
perf: perf_event_exit_task_context: s/rcu_dereference/rcu_dereference_raw/
perf test: Use cpu_map->[cpu] when setting affinity
perf symbols: Fix annotation of thumb code
perf: Annotate cpuctx->ctx.mutex to avoid a lockdep splat
powerpc, perf: Fix frequency calculation for overflowing counters (FSL version)
perf: Fix perf_event_init_task()/perf_event_free_task() interaction
perf: Fix find_get_context() vs perf_event_exit_task() race
Linus Torvalds [Mon, 24 Jan 2011 19:25:13 +0000 (05:25 +1000)]
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix poor interactivity on UP systems due to group scheduler nice tune bug
Linus Torvalds [Mon, 24 Jan 2011 19:24:12 +0000 (05:24 +1000)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix jump label with RO/NX module protection crash
x86, hotplug: Fix powersavings with offlined cores on AMD
x86, mcheck, therm_throt.c: Export symbol platform_thermal_notify to allow coretemp to handler intr
x86: Use asm-generic/cacheflush.h
x86: Update CPU cache attributes table descriptors
can: at91_can: make can_id of mailbox 0 configurable
Due to a chip bug (errata 50.2.6.3 & 50.3.5.3 in
"AT91SAM9263 Preliminary 6249H-ATARM-27-Jul-09") the contents of mailbox
0 may be send under certain conditions (even if disabled or in rx mode).
The workaround in the errata suggests not to use the mailbox and load it
with an unused identifier.
This patch implements the second part of the workaround. A sysfs entry
"mb0_id" is introduced. While the interface is down it can be used to
configure the can_id of mailbox 0. The default value id 0x7ff.
In order to use an extended can_id add the CAN_EFF_FLAG (0x80000000U)
to the can_id. Example:
- standard id 0x7ff:
echo 0x7ff > /sys/class/net/can0/mb0_id
- extended id 0x1fffffff:
echo 0x9fffffff > /sys/class/net/can0/mb0_id
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
For the Documentation-part: Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Due to a chip bug (errata 50.2.6.3 & 50.3.5.3 in
"AT91SAM9263 Preliminary 6249H-ATARM-27-Jul-09") the contents of mailbox
0 may be send under certain conditions (even if disabled or in rx mode).
The workaround in the errata suggests not to use the mailbox and load it
with a unused identifier.
This patch implements the first part of the workaround, it updates
AT91_MB_RX_NUM and AT91_MB_RX_FIRST (and the inline documentation)
so that mailbox 0 stays unused.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
can: at91_can: clean up usage of AT91_MB_RX_FIRST and AT91_MB_RX_NUM
This patch cleans up the usage of two macros which specify the mailbox
usage. AT91_MB_RX_FIRST and AT91_MB_RX_NUM define the first and the
number of RX mailboxes. The current driver uses these variables in an
unclean way; assuming that AT91_MB_RX_FIRST is 0;
This patch cleans up the usage of these macros, no longer assuming
AT91_MB_RX_FIRST == 0.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Yong Zhang [Mon, 24 Jan 2011 07:33:52 +0000 (15:33 +0800)]
sched: Fix poor interactivity on UP systems due to group scheduler nice tune bug
Michael Witten and Christian Kujau reported that the autogroup
scheduling feature hurts interactivity on their UP systems.
It turns out that this is an older bug in the group scheduling code,
and the wider appeal provided by the autogroup feature exposed it
more prominently.
When on UP with FAIR_GROUP_SCHED enabled, tune shares
only affect tg->shares, but is not reflected in
tg->se->load. The reason is that update_cfs_shares()
does nothing on UP.
So introduce update_cfs_shares() for UP && FAIR_GROUP_SCHED.
This issue was found when enable autogroup scheduling was enabled,
but it is an older bug that also exists on cgroup.cpu on UP.
Reported-and-Tested-by: Michael Witten <mfwitten@gmail.com> Reported-and-Tested-by: Christian Kujau <christian@nerdbynature.de> Signed-off-by: Yong Zhang <yong.zhang0@gmail.com> Acked-by: Pekka Enberg <penberg@kernel.org> Acked-by: Mike Galbraith <efault@gmx.de> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110124073352.GA24186@windriver.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds [Mon, 24 Jan 2011 09:58:39 +0000 (19:58 +1000)]
Merge branch 'BUG_ON' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus
* 'BUG_ON' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
Remove MAYBE_BUILD_BUG_ON
BUILD_BUG_ON: make it handle more cases
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
module: fix missing semicolons in MODULE macro usage
param: add null statement to compiled-in module params
module: fix linker error for MODULE_VERSION when !MODULE and CONFIG_SYSFS=n
module: show version information for built-in modules in sysfs
Rusty Russell [Mon, 24 Jan 2011 20:45:10 +0000 (14:45 -0600)]
BUILD_BUG_ON: make it handle more cases
BUILD_BUG_ON used to use the optimizer to do code elimination or fail
at link time; it was changed to first the size of a negative array (a
nicer compile time error), then (in 8c87df457cb58fe75b9b893007917cf8095660a0) to a bitfield.
This forced us to change some non-constant cases to MAYBE_BUILD_BUG_ON();
as Jan points out in that commit, it didn't work as intended anyway.
bitfields: needs a literal constant at parse time, and can't be put under
"if (__builtin_constant_p(x))" for example.
negative array: can handle anything, but if the compiler can't tell it's
a constant, silently has no effect.
link time: breaks link if the compiler can't determine the value, but the
linker output is not usually as informative as a compiler error.
If we use the negative-array-size method *and* the link time trick,
we get the ability to use BUILD_BUG_ON() under __builtin_constant_p()
branches, and maximal ability for the compiler to detect errors at
build time.
We also document it thoroughly.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Jan Beulich <JBeulich@novell.com> Acked-by: Hollis Blanchard <hollisb@us.ibm.com>
Linus Walleij [Wed, 5 Jan 2011 12:27:04 +0000 (13:27 +0100)]
param: add null statement to compiled-in module params
Add an unused struct declaration statement requiring a
terminating semicolon to the compile-in case to provoke an
error if __MODULE_INFO() is used without the terminating
semicolon. Previously MODULE_ALIAS("foo") (no semicolon)
compiled fine if MODULE was not selected.
Cc: Dan Carpenter <error27@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty Russell [Mon, 24 Jan 2011 20:32:51 +0000 (14:32 -0600)]
module: fix linker error for MODULE_VERSION when !MODULE and CONFIG_SYSFS=n
lib/built-in.o:(__modver+0x8): undefined reference to `__modver_version_show'
lib/built-in.o:(__modver+0x2c): undefined reference to `__modver_version_show'
Simplest to just not emit anything: if they've disabled SYSFS they probably
want the smallest kernel possible.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Dmitry Torokhov [Wed, 15 Dec 2010 22:00:19 +0000 (14:00 -0800)]
module: show version information for built-in modules in sysfs
Currently only drivers that are built as modules have their versions
shown in /sys/module/<module_name>/version, but this information might
also be useful for built-in drivers as well. This especially important
for drivers that do not define any parameters - such drivers, if
built-in, are completely invisible from userspace.
This patch changes MODULE_VERSION() macro so that in case when we are
compiling built-in module, version information is stored in a separate
section. Kernel then uses this data to create 'version' sysfs attribute
in the same fashion it creates attributes for module parameters.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Olof Johansson [Fri, 7 Jan 2011 03:24:01 +0000 (21:24 -0600)]
tpm: fix panic caused by "tpm: Autodetect itpm devices"
commit 3f0d3d016d89a5efb8b926d4707eb21fa13f3d27 adds a check for
PNP device id to the common tpm_tis_init() function, which in some
cases (force=1) will be called without the device being a member of
a pnp_dev. Oopsing and panics ensue.
Move the test up to before the call to tpm_tis_init(), since it
just modifies a global variable anyway.
Signed-off-by: Olof Johansson <olof@lixom.net> Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com> Signed-off-by: James Morris <jmorris@namei.org>
Rajiv Andrade [Fri, 12 Nov 2010 21:30:02 +0000 (22:30 +0100)]
TPM: Long default timeout fix
If duration variable value is 0 at this point, it's because
chip->vendor.duration wasn't filled by tpm_get_timeouts() yet.
This patch sets then the lowest timeout just to give enough
time for tpm_get_timeouts() to further succeed.
This fix avoids long boot times in case another entity attempts
to send commands to the TPM when the TPM isn't accessible.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com> Signed-off-by: James Morris <jmorris@namei.org>
Jesper Juhl [Sun, 23 Jan 2011 21:40:42 +0000 (22:40 +0100)]
trusted keys: Fix a memory leak in trusted_update().
One failure path in security/keys/trusted.c::trusted_update() does
not free 'new_p' while the others do. This patch makes sure we also free
it in the remaining path (if datablob_parse() returns different from
Opt_update).
Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: James Morris <jmorris@namei.org>
Randy Dunlap [Sun, 23 Jan 2011 04:16:06 +0000 (20:16 -0800)]
fs: fix new dcache.c kernel-doc warnings
Fix new fs/dcache.c kernel-doc warnings:
Warning(fs/dcache.c:184): No description found for parameter 'dentry'
Warning(fs/dcache.c:296): No description found for parameter 'parent'
Warning(fs/dcache.c:1985): No description found for parameter 'dparent'
Warning(fs/dcache.c:1985): Excess function parameter 'parent' description in 'd_validate'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Nick Piggin <npiggin@kernel.dk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Sun, 23 Jan 2011 04:16:12 +0000 (20:16 -0800)]
rapidio: fix new kernel-doc warnings
Fix new rapidio kernel-doc warnings:
Warning(drivers/rapidio/rio-scan.c:953): No description found for parameter 'prev'
Warning(drivers/rapidio/rio-scan.c:953): No description found for parameter 'prev_port'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Matt Porter <mporter@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[acme@localhost linux]$ make O=~acme/git/build/perf -C tools/perf
make: Entering directory `/home/acme/git/linux/tools/perf'
Makefile:526: No libdw.h found or old libdw.h found or elfutils is older than 0.138, disables dwarf support. Please install new elfutils-devel/libdw-dev
Makefile:582: newt not found, disables TUI support. Please install newt-devel or libnewt-dev
CC /home/acme/git/build/perf/builtin-annotate.o
In file included from builtin-annotate.c:23:
util/parse-events.h:26: warning: declaration of 'evsel_list' shadows a global declaration
util/parse-events.h:12: warning: shadowed declaration is here
make: *** [/home/acme/git/build/perf/builtin-annotate.o] Error 1
make: Leaving directory `/home/acme/git/linux/tools/perf'
[acme@localhost linux]$ gcc --version | head -1
gcc (GCC) 3.4.6 20060404 (Red Hat 3.4.6-11)
[acme@localhost linux]$
Fix it by renaming the parameter to evlist.
Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We need the definiton for __always_inline in bitops.h to fix the build
on distros where it isn't available or compiler.h doesn't get included
indirectly.
One of the fixes needed to build perf on RHEL4 systems, for instance.
Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Using %L[uxd] has issues in some architectures, like on ppc64. Fix it
by making our 64 bit integers typedefs of stdint.h types and using
PRI[ux]64 like, for instance, git does.
Reported by Denis Kirjanov that provided a patch for one case, I went
and changed all cases.
Reported-by: Denis Kirjanov <dkirjanov@kernel.org> Tested-by: Denis Kirjanov <dkirjanov@kernel.org>
LKML-Reference: <20110120093246.GA8031@hera.kernel.org> Cc: Denis Kirjanov <dkirjanov@kernel.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Pingtian Han <phan@redhat.com> Cc: Stephane Eranian <eranian@google.com> Cc: Tom Zanussi <tzanussi@gmail.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Where we don't have CPU_ALLOC & friends. As the tools are being used in older
distros where the only allowed change are to replace the kernel, like RHEL4 and
5.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Paul Mackerras <paulus@samba.org> Cc: Stephane Eranian <eranian@google.com>
LKML-Reference: <new-submission> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kurt Van Dijck [Tue, 11 Jan 2011 04:34:28 +0000 (04:34 +0000)]
can: add driver for Softing card
This patch adds the driver that creates a platform:softing device
from a pcmcia_device
Note: the Kconfig indicates a dependency on the softing.ko driver,
but this is purely to make configuration intuitive. This driver will
work independent, but no CAN network devices appear until softing.ko is
loaded too.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kurt Van Dijck [Tue, 11 Jan 2011 04:32:31 +0000 (04:32 +0000)]
can: add driver for Softing card
This patch adds a driver for the platform:softing device.
This will create (up to) 2 CAN network devices from 1
platform:softing device
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Borislav Petkov [Thu, 20 Jan 2011 14:42:52 +0000 (15:42 +0100)]
x86, hotplug: Fix powersavings with offlined cores on AMD
ea53069231f9317062910d6e772cca4ce93de8c8 made a CPU use monitor/mwait
when offline. This is not the optimal choice for AMD wrt to powersavings
and we'd prefer our cores to halt (i.e. enter C1) instead. For this, the
same selection whether to use monitor/mwait has to be used as when we
select the idle routine for the machine.
With this patch, offlining cores 1-5 on a X6 machine allows core0 to
boost again.
[ hpa: putting this in urgent since it is a (power) regression fix ]
Reported-by: Andreas Herrmann <andreas.herrmann3@amd.com> Cc: stable@kernel.org # 37.x Cc: H. Peter Anvin <hpa@linux.intel.com> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Len Brown <lenb@kernel.org> Cc: Venkatesh Pallipadi <venki@google.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.hl> Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1295534572-10730-1-git-send-email-bp@amd64.org> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Linus Torvalds [Sat, 22 Jan 2011 00:50:31 +0000 (16:50 -0800)]
Merge branch 'media_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'media_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (101 commits)
[media] staging/lirc: fix mem leaks and ptr err usage
[media] hdpvr: reduce latency of i2c read/write w/recycled buffer
[media] hdpvr: enable IR part
[media] rc/mceusb: timeout should be in ns, not us
[media] v4l2-device: fix 'use-after-freed' oops
[media] v4l2-dev: don't memset video_device.dev
[media] zoran: use video_device_alloc instead of kmalloc
[media] w9966: zero device state after a detach
[media] v4l: Fix a use-before-set in the control framework
[media] v4l: Include linux/videodev2.h in media/v4l2-ctrls.h
[media] DocBook/v4l: update V4L2 revision and update copyright years
[media] DocBook/v4l: fix validation error in dev-rds.xml
[media] v4l2-ctrls: queryctrl shouldn't attempt to replace V4L2_CID_PRIVATE_BASE IDs
[media] v4l2-ctrls: fix missing 'read-only' check
[media] pvrusb2: Provide more information about IR units to lirc_zilog and ir-kbd-i2c
[media] ir-kbd-i2c: Add back defaults setting for Zilog Z8's at addr 0x71
[media] lirc_zilog: Update TODO.lirc_zilog
[media] lirc_zilog: Add Andy Walls to copyright notice and authors list
[media] lirc_zilog: Remove useless struct i2c_driver.command function
[media] lirc_zilog: Remove unneeded tests for existence of the IR Tx function
...
Vasiliy Kulikov [Sat, 22 Jan 2011 00:24:23 +0000 (16:24 -0800)]
atm: idt77105: fix fetch_stats() result
copy_to_user() used PRIV(dev)->stats instead of local stats variable.
Zero stats were returned to user in case of (zero != 0), also memcpy()
was pointless.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Thu, 20 Jan 2011 16:38:27 +0000 (16:38 +0000)]
KEYS: Do some style cleanup in the key management code.
Do a bit of a style clean up in the key management code. No functional
changes.
Done using:
perl -p -i -e 's!^/[*]*/\n!!' security/keys/*.c
perl -p -i -e 's!} /[*] end [a-z0-9_]*[(][)] [*]/\n!}\n!' security/keys/*.c
sed -i -s -e ": next" -e N -e 's/^\n[}]$/}/' -e t -e P -e 's/^.*\n//' -e "b next" security/keys/*.c
To remove /*****/ lines, remove comments on the closing brace of a
function to name the function and remove blank lines before the closing
brace of a function.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: fix up CIFSSMBEcho for unaligned access
cifs: fix unaligned accesses in cifsConvertToUCS
cifs: clean up unaligned accesses in cifs_unicode.c
cifs: fix unaligned access in check2ndT2 and coalesce_t2
cifs: clean up unaligned accesses in validate_t2
cifs: use get/put_unaligned functions to access ByteCount
cifs: move time field in cifsInodeInfo
cifs: TCP_Server_Info diet
CIFS: Implement cifs_strict_readv (try #4)
CIFS: Implement cifs_file_strict_mmap (try #2)
CIFS: Implement cifs_strict_fsync
CIFS: Make cifsFileInfo_put work with strict cache mode
Linus Torvalds [Fri, 21 Jan 2011 21:38:57 +0000 (13:38 -0800)]
Merge branch 'fixes-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
* 'fixes-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: note the nested NOT_RUNNING test in worker_clr_flags() isn't a noop
workqueue: relax lockdep annotation on flush_work()
Linus Torvalds [Fri, 21 Jan 2011 21:34:39 +0000 (13:34 -0800)]
Merge branches 'fixes' and 'fwnet' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: core: fix unstable I/O with Canon camcorder
* 'fwnet' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: net: is not experimental anymore
firewire: net: invalidate ARP entries of removed nodes
In theory, almost every user of task->child->perf_event_ctxp[]
is wrong. find_get_context() can install the new context at any
moment, we need read_barrier_depends().
dbe08d82ce3967ccdf459f7951d02589cf967300 "perf: Fix
find_get_context() vs perf_event_exit_task() race" added
rcu_dereference() into perf_event_exit_task_context() to make
the precedent, but this makes __rcu_dereference_check() unhappy.
Use rcu_dereference_raw() to shut up the warning.
Jesper Juhl [Fri, 21 Jan 2011 19:40:54 +0000 (13:40 -0600)]
rtlwifi: Fix possible NULL dereference
In drivers/net/wireless/rtlwifi/pci.c::_rtl_pci_rx_interrupt() we call
dev_alloc_skb(), which may fail and return NULL, but we do not check the
returned value against NULL before dereferencing the returned pointer.
This may lead to a NULL pointer dereference which means we'll crash - not
good.
In a separate call to dev_alloc_skb(), the debug level is changed so that
the failure message will always be logged.
Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-beck.git / log