Avinash Patil [Fri, 23 Aug 2013 23:48:22 +0000 (16:48 -0700)]
mwifiex: fix ext_capab IE structure definition
EXT_CAPAB_IE format involves IEEE header followed by bytestream of
capabilities. Current structure has incorrect member u8 for data;
fix it by defining it as u8[0].
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Fri, 23 Aug 2013 23:48:21 +0000 (16:48 -0700)]
mwifiex: fix driver unload problem for usb chipsets
We have usb_deregister() call in our rmmod routine. deauth,
shutdown etc. commands will be sent to FW later when bus
driver calls disconnect handler.
This mechanism works fine with SDIO and PCIe interfaces, but
there is an issue with USB.
USB bus driver returns all URBs submitted for receiving data
and command response immediately after usb_deregister() with
failure status. Hence we don't send deauth, shutdown etc.
command to firmware.
The problem is fixed by moving code from disconnect handler to
rmmod routine for USB interface.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Fri, 23 Aug 2013 22:32:30 +0000 (00:32 +0200)]
bcma: add method to power up and down the PCIe core by wifi driver
The wifi driver should tell the PCIe core that it is now in operation
so that some workarounds can be applied and the power state is changed.
This should replace the call to bcma_core_pci_extend_L1timer by the
brcmsmac driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Fri, 23 Aug 2013 21:22:29 +0000 (23:22 +0200)]
bcma: change max PCI read request size to 128
This PCIe controller does not support a max read request size above 128
bytes. The sold card I tested this controller with used 128 as default
value, but some new routers are sold with BCM4331 chips, which have a
default max read request size of 512. This device fails at the first
DMA reqeust whch is bigger than 126 bytes.
This patch changes the max read request size to 128 for every device on
the PCIe link.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 22 Aug 2013 18:53:22 +0000 (20:53 +0200)]
rt2x00: rt2800lib: don't hardcode beacon offsets
The values written into the BCN_OFFSET[01] registers are
hardcoded in the rt2800_init_register function.
Add a macro and a helper function to derive these values
directly from the base address of a given beacon, and use
the new function instead of the hardcoded numbers.
The patch contains no functional changes. The programmed
register values are the same before and after the patch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW_BEACON_BASE() macro returns the base address
of a given beacon, however the returned values are
not usable on all chipsets. On devices which have
selectable shared memory parts, some beacon may be
located in the high part of the shared memory.
Instead of extending the already complicated macro,
add a new helper function and use that to get the
base address of a given beacon.
The actual patch contains no functional changes, the
helper function will be extended in a further patch
to handle different chipsets' requirements.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Wed, 21 Aug 2013 09:45:47 +0000 (11:45 +0200)]
brcmsmac: add support for BCM4313 iPA variant
This patch completes the changes needed for supporting the
iPA variant cards of the BCM4313 wireless chipset.
Tested-by: David Herrmann <dh.herrmann@gmail.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 20 Aug 2013 14:00:45 +0000 (16:00 +0200)]
brcmsmac: reinitialize TSSI power control upon channel switch
When changing channels the TSSI based power control needs to be
reinitialized.
Tested-by: David Herrmann <dh.herrmann@gmail.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 20 Aug 2013 14:00:44 +0000 (16:00 +0200)]
brcmsmac: correct phy registers for TSSI-based power control
A number of additional phy registers needs to be programmed when
using TSSI-based power control.
Tested-by: David Herrmann <dh.herrmann@gmail.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 20 Aug 2013 14:00:43 +0000 (16:00 +0200)]
brcmsmac: rework switch control table init including iPA BT-combo
Rework the code path in lcnphy tbl_init() for switch control
table programming. This also takes the iPA BT-combo card into
account.
Tested-by: David Herrmann <dh.herrmann@gmail.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
For lcnphy revision 1 or when hardware supports i/q calibration the
function wlc_lcnphy_set_txpwr_by_index() was called twice.
Tested-by: David Herrmann <dh.herrmann@gmail.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 20 Aug 2013 14:00:41 +0000 (16:00 +0200)]
brcmsmac: fix TSSI idle estimation
The baseband multiplier must be zero during TSSI idle estimation
and restored afterwards.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Tested-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The gain level control for the test tone has been changed. This
calbration test tone is used to determine the i/q compensation.
The i/q calibration routine has been reworked to accomodate this.
Cc: Jonas Gorski <jogo@openwrt.org> Tested-by: David Herrmann <dh.herrmann@gmail.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 20 Aug 2013 14:00:39 +0000 (16:00 +0200)]
brcmsmac: update transmit gain table for lcn phy
Update the transmit gain table for bcm4313 chip family.
Tested-by: David Herrmann <dh.herrmann@gmail.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 20 Aug 2013 14:00:38 +0000 (16:00 +0200)]
brcmsmac: add debug info message providing phy and radio info
For debug purposes it is good to have the phy and radio information
available in the log. Only logged when driver is built when BRCMDBG
or BRCM_TRACING kconfig are set.
Tested-by: David Herrmann <dh.herrmann@gmail.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 20 Aug 2013 14:00:37 +0000 (16:00 +0200)]
brcmsmac: use ARRAY_SIZE in phytbl_lcn.c
This patch converts all sizeof(x)/sizeof(x[0]) instances to
ARRAY_SIZE macro in phytbl_lcn.c. The patch was made using
spatch with ARRAY_SIZE.cocci (see [1]).
Arend van Spriel [Tue, 20 Aug 2013 14:00:36 +0000 (16:00 +0200)]
brcmsmac: change pa_gain for bcm4313 iPA
The function wlc_lcnphy_load_tx_gain_table() has a target PA
gain specified for the iPA variant of the bcm4313. This gain
value is reduced to avoid PA distortion. The if-statement is
removed because it was rather redundant in the first place.
Please note that this patch does not provide full iPA support.
Cc: Jonas Gorski <jogo@openwrt.org> Tested-by: David Herrmann <dh.herrmann@gmail.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 20 Aug 2013 14:00:35 +0000 (16:00 +0200)]
brcmsmac: cosmetic change in phy_lcn.c
Cleaning up some code fragments reducing indentation and uncluttering
some lines. Apart from whitespace there are no actual code changes
made.
Cc: Jonas Gorski <jogo@openwrt.org> Tested-by: David Herrmann <dh.herrmann@gmail.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Network Manager attempts to use all 3 interfaces above without
filtering the managed interface type. As the result, 3 identical
interfaces are displayed under network manager. If user happens to
click on an entry under which its interface is uap0 or p2p0, the
association will fail.
Work around it by removing the creation of AP and P2P interfaces
at driver loading time. These interfaces can be added with 'iw' or
other applications manually when they are needed.
Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Sat, 17 Aug 2013 12:09:33 +0000 (14:09 +0200)]
rt2x00: rt2800lib: adjust frequency offset for RF3053
Along with other chipsets, the Ralink driver uses the
frequency adjustment code for RF3053 as well. Remove
the bogus place-holder comment from the RF3053 specific
channel configuration function and call the frequency
adjustment function instead
Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
RT3593_ChipSwitchChannel function in chips/rt3593.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Sat, 17 Aug 2013 12:09:31 +0000 (14:09 +0200)]
rt2x00: rt2800lib: use step-by-step frequency offset adjustment on MMIO devices
According to the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver, the RFCSR17 register can't be programmed in
one step on devices which are using the frequency
offset adjustment code.
Update the code to use step-by-step adjustment.
Reference:
RT30xxWriteRFRegister function in common/rt_rf.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Sat, 17 Aug 2013 12:09:30 +0000 (14:09 +0200)]
rt2x00: rt2800lib: use a MCU command for frequency adjustment on USB devices
According to the Ralink driver, there is an MCU
command which can be used to send the frequency
offset value directly to the USB device without
going through the RFCSR writing sequence.
Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
RTMPAdjustFrequencyOffset function in common/rt_rf.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Sat, 17 Aug 2013 12:09:29 +0000 (14:09 +0200)]
rt2x00: rt2800lib: optimize frequency offset adjustment
Don't write the new value into the register if it is
the same as the old value to avoid unncessary USB bus
traffic with USB devices. The change also saves a few
cycle on MMIO based devices.
Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
RTMPAdjustFrequencyOffset function in common/rt_rf.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Sat, 17 Aug 2013 12:09:28 +0000 (14:09 +0200)]
rt2x00: rt2800lib: fix frequency offset boundary calculation
The current code in the 'rt2800_adjust_freq_offset'
function limits the device specific frequency offset
value to FREQ_BOUND but ignores the fact that the
uppermost bit is not part of the frequency offset
value. As the result, the driver always uses the
FREQ_BOUND value if the uppermost bit is set.
Update the code to use the correct source value
for calculating the boundary.
Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
RTMPAdjustFrequencyOffset function in common/rt_rf.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Fri, 16 Aug 2013 22:15:50 +0000 (00:15 +0200)]
rt2x00: rt2800lib: pass beacon index to rt2800_clear_beacon_register
Instead of precomputing the beacon base in
each caller, pass the beacon index to the
'rt2800_clear_beacon_register' function
and compute the beacon base in there.
This allows to simplify the caller functions
a bit.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Fri, 16 Aug 2013 22:15:49 +0000 (00:15 +0200)]
rt2x00: rt2800: rename HW_BEACON_OFFSET macro
The name of the HW_BEACON_OFFSET macro is a
bit confusing. It returns with one of the
HW_BEACON_BASE* values, so rename the macro
to HW_BEACON_BASE to reflect that.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
When initiating a transparent eSCO connection, make use of T2 settings
at first try. T2 is the recommended settings from HFP 1.6 WideBand
Speech. Upon connection failure, try T1 settings.
When CVSD is requested and eSCO is supported, try to establish eSCO
connection using S3 settings. If it fails, fallback in sequence to S2,
S1, D1, D0 settings.
To know which setting should be used, conn->attempt is used. It
indicates the currently ongoing SCO connection attempt and can be used
as the index for the fallback settings table.
These setting and the fallback order are described in Bluetooth HFP 1.6
specification p. 101.
Bluetooth: Handle specific error for SCO connection fallback
Synchronous Connection Complete event can return error "Connection
Rejected due to Limited resources (0x10)".
Handling this error is required for SCO connection fallback. This error
happens when the server tried to accept the connection but failed to
negotiate settings.
This error code has been verified experimentally by sending a T2 request
to a T1 only SCO listener.
Bluetooth: Prevent transparent SCO on older devices
Older Bluetooth devices may not support Setup Synchronous Connection or
SCO transparent data. This is indicated by the corresponding LMP feature
bits. It is not possible to know if the adapter support these features
before setting BT_VOICE option since the socket is not bound to an
adapter. An adapter can also be added after the socket is created. The
socket can be bound to an address before adapter is plugged in.
Thus, on a such adapters, if user request BT_VOICE_TRANSPARENT, outgoing
connections fail on connect() and returns -EOPNOTSUPP. Incoming
connections do not fail. However, they should only be allowed depending
on what was specified in Write_Voice_Settings command.
EOPNOTSUPP is choosen because connect() system call is failing after
selecting route but before any connection attempt.
Bluetooth: Add constants and macro declaration for transparent data
This patch defines constants and macro for transparent data LMP
features. It refers to Bluetooth Core V4.0 specification, Part C, Chap
3.3 which defines LMP feature mask.
Bluetooth: Parameters for outgoing SCO connections
In order to establish a transparent SCO connection, the correct settings
must be specified in the Setup Synchronous Connection request. For that,
a setting field is added to ACL connection data to set up the desired
parameters. The patch also removes usage of hdev->voice_setting in CVSD
connection and makes use of T2 parameters for transparent data.
Bluetooth: Use voice setting in deferred SCO connection request
When an incoming eSCO connection is requested, check the selected voice
setting and reply appropriately. Voice setting should have been
negotiated previously. For example, in case of HFP, the codec is
negotiated using AT commands on the RFCOMM channel. This patch only
changes replies for socket with deferred setup enabled.
This patch defines constants for SCO airmode from SCO voice setting. It
refers to Bluetooth Core V4.0 specification, Part E, Chap 6.12 which
describe SCO voice setting format.
This patch extends the current Bluetooth socket options with BT_VOICE.
This is intended to choose voice data type at runtime. It only applies
to SCO sockets. Incoming connections shall be setup during deferred
setup. Outgoing connections shall be setup before connect(). The desired
setting is stored in the SCO socket info. This patch declares needed
members, modifies getsockopt() and setsockopt().
Bluetooth: Remove unused mask parameter in sco_conn_defer_accept
From Bluetooth Core v4.0 specification, 7.1.8 Accept Connection Request
Command "When accepting synchronous connection request, the Role
parameter is not used and will be ignored by the BR/EDR Controller."
hci_connect is a super function for connecting hci protocols. But the
voice_setting parameter (introduced in subsequent patches) is only
needed by SCO and security requirements are not needed for SCO channels.
Thus, it makes sense to have a separate function for SCO.
Bluetooth: Purge the dlc->tx_queue to avoid circular dependency
In rfcomm_tty_cleanup we purge the dlc->tx_queue which may contain
socket buffers referencing the tty_port and thus preventing the tty_port
destruction.
The tty_port can be released in two cases: when we get a HUP in the
functions rfcomm_tty_hangup() and rfcomm_dev_state_change(). Or when the
user releases the device in rfcomm_release_dev().
In these cases we set the flag RFCOMM_TTY_RELEASED so that no other
function can get a reference to the tty_port.
The use of !test_and_set_bit(RFCOMM_TTY_RELEASED) ensures that the
'initial' tty_port reference is only dropped once.
The rfcomm_dev_del function is removed becase it isn't used anymore.
Bluetooth: Implement .activate, .shutdown and .carrier_raised methods
Implement .activate, .shutdown and .carrier_raised methods of tty_port
to manage the dlc, moving the code from rfcomm_tty_install() and
rfcomm_tty_cleanup() functions.
At the same time the tty .open()/.close() and .hangup() methods are
changed to use the tty_port helpers that properly call the
aforementioned tty_port methods.
Bluetooth: Move the tty initialization and cleanup out of open/close
Move the tty_struct initialization from rfcomm_tty_open() to
rfcomm_tty_install() and do the same for the cleanup moving the code from
rfcomm_tty_close() to rfcomm_tty_cleanup().
Add also extra error handling in rfcomm_tty_install() because, unlike
.open()/.close(), .cleanup() is not called if .install() fails.
Bluetooth: Remove the device from the list in the destructor
The current code removes the device from the device list in several
places. Do it only in the destructor instead and in the error path of
rfcomm_add_dev() if the device couldn't be initialized.
In net/bluetooth/rfcomm/tty.c the struct tty_struct is used without
taking references. This may lead to a use-after-free of the rfcomm tty.
Fix this by taking references properly, using the tty_port_* helpers
when possible.
The raw assignments of dev->port.tty in rfcomm_tty_open/close are
addressed in the later commit 'rfcomm: Implement .activate, .shutdown
and .carrier_raised methods'.
Marcel Holtmann [Tue, 13 Aug 2013 17:00:54 +0000 (10:00 -0700)]
Bluetooth: Set different event mask for LE-only controllers
In case of a Low Energy only controller it makes no sense to configure
the full BR/EDR event mask. It will just enable events that can not be
send anyway and there is no guarantee that such a controller will accept
this value.
Use event mask 0x90 0xe8 0x04 0x02 0x00 0x80 0x00 0x20 for LE-only
controllers which enables the following events:
Disconnection Complete
Encryption Change
Read Remote Version Information Complete
Command Complete
Command Status
Hardware Error
Number of Completed Packets
Data Buffer Overflow
Encryption Key Refresh Complete
LE Meta
This is according to Core Specification, Part E, Section 3.
Johan Hedberg [Thu, 8 Aug 2013 11:53:56 +0000 (14:53 +0300)]
Bluetooth: Fix getting SCO socket options in deferred state
When a socket is in deferred state there does actually exist an
underlying connection even though the connection state is not yet
BT_CONNECTED. In the deferred state it should therefore be allowed to
get socket options that usually depend on a connection, such as
SCO_OPTIONS and SCO_CONNINFO.
This patch fixes the behavior of some user space code that behaves as
follows without it:
$ sudo tools/btiotest -i 00:1B:DC:xx:xx:xx -d -s
accept=2 reject=-1 discon=-1 defer=1 sec=0 update_sec=0 prio=0 voice=0x0000
Listening for SCO connections
bt_io_get(OPT_DEST): getsockopt(SCO_OPTIONS): Transport endpoint is not connected (107)
Accepting connection
Successfully connected to 60:D8:19:xx:xx:xx. handle=43, class=000000
The conditions that the patch updates the if-statements to is taken from
similar code in l2cap_sock.c which correctly handles the deferred state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The rt2800pci driver uses the same [RT]XWI size
for all chipsets, however some chips requires
different values.
The size of the [RT]XWI structures is a constant
value for a given chipset and it does not depend
on the underlying interface. Add a helper function
which returns the correct values for the actual
chipset and use the new helper both in the rt2800usb
and in the rt2800pci drivers. This ensures that both
drivers are using the correct values.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simon Wunderlich [Wed, 14 Aug 2013 06:01:38 +0000 (08:01 +0200)]
ath9k: enable CSA functionality in ath9k
CSA is only enabled for one interface, but the same limitation applies
for mac80211 too. It checks whether the beacon has been sent (different
approaches for non-EDMA-enabled and EDMA-enabled devices), and completes
the channel switch after that.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simon Wunderlich [Wed, 14 Aug 2013 06:01:37 +0000 (08:01 +0200)]
ath5k: enable support for 5 MHz and 10 MHz channels
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simon Wunderlich [Wed, 14 Aug 2013 06:01:36 +0000 (08:01 +0200)]
ath5k: set 5/10 MHz supported channels and fix duration
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simon Wunderlich [Wed, 14 Aug 2013 06:01:35 +0000 (08:01 +0200)]
ath5k: report 5/10 MHz channels
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simon Wunderlich [Wed, 14 Aug 2013 06:01:34 +0000 (08:01 +0200)]
ath9k: announce that ath9k supports 5/10 MHz
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simon Wunderlich [Wed, 14 Aug 2013 06:01:33 +0000 (08:01 +0200)]
ath9k: set 5/10 MHz supported channels and fix bitrate
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simon Wunderlich [Wed, 14 Aug 2013 06:01:32 +0000 (08:01 +0200)]
ath9k: report 5/10 MHz channels
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simon Wunderlich [Fri, 16 Aug 2013 08:46:04 +0000 (10:46 +0200)]
ath9k: use chandef instead of channel_type
To enable support for 5/10 MHz, some internal functions must be
converted from using the (old) channel_type to chandef. This is a good
chance to change all remaining occurences.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simon Wunderlich [Wed, 14 Aug 2013 06:01:30 +0000 (08:01 +0200)]
ath9k: always use SIFS times from OFDM for 5/10 MHz
5/10 MHz channels should always use SIFS times as defined in IEEE
802.11-2012 18.4.4 (OFDM PHY characteristics). This makes it compatible
to ath5k, which does the same.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 7 Aug 2013 18:11:55 +0000 (20:11 +0200)]
mac80211: add APIs to allow keeping connections after WoWLAN
In order to be able to (securely) keep connections alive after
the system was suspended for WoWLAN, we need some additional
APIs. We already have API (ieee80211_gtk_rekey_notify) to tell
wpa_supplicant about the new replay counter if GTK rekeying
was done by the device while the host was asleep, but that's
not sufficient.
If GTK rekeying wasn't done, we need to tell the host about
sequence counters for the GTK (and PTK regardless of rekeying)
that was used while asleep, add ieee80211_set_key_rx_seq() for
that.
If GTK rekeying was done, then we need to be able to disable
the old keys (with ieee80211_remove_key()) and allocate the
new GTK key(s) in mac80211 (with ieee80211_gtk_rekey_add()).
If protocol offload (e.g. ARP) is implemented, then also the
TX sequence counter for the PTK must be updated, using the new
ieee80211_set_key_tx_seq() function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211: move ibss presp generation in own function
Channel Switch will later require to generate beacons without setting
them immediately. Therefore split the presp generation in an own
function. Splitting the original very long function might be a good idea
anyway.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johan Almbladh [Wed, 14 Aug 2013 13:29:46 +0000 (15:29 +0200)]
mac80211: perform power save processing before decryption
This patch decouples the power save processing from the frame decryption
by running the decrypt rx handler after sta_process. In the case where
the decryption failed for some reason, the stack used to not process
the PM and MOREDATA bits for that frame. The stack now always performs
power save processing regardless of the decryption result. That means that
encrypted data frames and NULLFUNC frames are now handled in the same way
regarding power save processing, making the stack more robust.
Signed-off-by: Johan Almbladh <ja@anyfi.net> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Performance Based Window snooze mechanism is based on uAPSD and is
used in low-medium traffic scenarios, in order to provide better power
performance while insuring low latency and jitter for the incoming traffic.
This patch enables PBW snoozing in case uAPSD is enabled and all ACs are
uAPSD trigger and delivery enabled.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use beacon statistics notification to track RSSI.
Notify mac80211 when the tresholds are crossed.
The roaming treshold is configured to be
equal to cqm_thold. If the beacon filtering command
is not supported by fw fall back and use mac80211
mechanism.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Luciano Coelho [Tue, 13 Aug 2013 07:34:55 +0000 (10:34 +0300)]
iwlwifi: return -ENOMEM instead of NULL when OOM in iwl_drv_start()
The callers of iwl_drv_start() are probe functions. If a probe
function returns 0, it means it succeeded. So if NULL was returned by
iwl_drv_start(), it would be considered as a success.
Fix this by returning -ENOMEM if the driver struct allocation fails in
iwl_drv_start().
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 6 Aug 2013 16:28:26 +0000 (18:28 +0200)]
iwlwifi: mvm: refactor resume from WoWLAN code
To be able to add more logic to the resume code, refactor it a bit,
moving some status checking/reporting logic into a new function.
The locking becomes a bit odd (one of the new functions now unlocks
the mutex) but this will be required to call new mac80211 APIs in
there later.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the patch adds a new failure mechanism to dma_rxfill(). When I changed the
comment at the start of the routine to add that information, I also polished
the wording.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Cc: Brett Rudley <brudley@broadcom.com> Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com> Cc: Hante Meuleman <meuleman@broadcom.com> Cc: brcm80211-dev-list@broadcom.com Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark Schulte [Wed, 31 Jul 2013 07:08:27 +0000 (00:08 -0700)]
rtlwifi: sparse warnings: cast to restricted type
Adding type casts to suppress sparse warnings:
* warning: cast to restricted __le32/__le16
Signed-off-by: Mark Schulte <schultetwin@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Wed, 14 Aug 2013 15:45:57 +0000 (21:15 +0530)]
ath9k: Use lockless variant to initialize RX fifo
Since the rx_fifo queue is accessed only using the various
lockless SKB queue routines, there is no need to initialize
the lock and __skb_queue_head_init() can be used.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Wed, 14 Aug 2013 15:45:56 +0000 (21:15 +0530)]
ath9k: Optimize LNA check
The documentation for antenna diversity says:
"The decision of diversity is done at 802.11 preamble. So, for
11G/11B, for every MAC packet hardware will do a decision. But in
11N with aggregation, the decision is made only at the preamble and
all other MPDUs will use the same LNA as the first MPDU."
Make use of rs_firstaggr to avoid needlessly scanning for LNA
changes.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Wed, 14 Aug 2013 03:41:21 +0000 (09:11 +0530)]
ath9k: Fix error condition for corrupt descriptors
In case a descriptor has the "done" bit clear and the
next descriptor has it set, we drop both of them. If
the packet that is received after these two packets
is dropped for some reason, "discard_next" will not cleared.
Fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Wed, 14 Aug 2013 03:41:10 +0000 (09:11 +0530)]
ath9k: Fix phy error handling for DFS
Since the DFS code appears to process the phy errors
ATH9K_PHYERR_RADAR and ATH9K_PHYERR_FALSE_RADAR_EXT,
check for the correct phyerr status in the main RX
tasklet routine.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Oleksij Rempel [Tue, 13 Aug 2013 19:10:19 +0000 (21:10 +0200)]
ath9k_htc: do not use bulk on EP3 and EP4
If usb auto suspend is enabled or system run in to suspend/resume
cycle, ath9k-htc adapter will stop to response. It is reproducible on xhci HCs.
Host part of problem:
XHCI do timing calculation based on Transfer Type and bInterval,
immediately after device was detected. Ath9k-htc try to overwrite
this parameters on module probe and some changes in FW,
since we do not initiate usb reset from the driver this changes
are not took to account. So, before any kind of suspend or reset,
host controller will operate with old parameters. Only after suspend/resume
and if interface id stay unchanged, new parameters will by applied. Host
will send bulk data with no intervals (?), which will cause
overflow on FIFO of EP4.
Firmware part of problem:
By default, ath9k-htc adapters configured with EP3 and EP4
as interrupt endpoints. Current firmware will try to overwrite
ConfigDescriptor to make EP3 and EP4 bulk. FIFO for this endpoints
stay not reconfigured, so under the hood it is still Int EP.
This patch is revert of 4a0e8ecca4ee commit which trying to
reduce CPU usage on some systems. Since it will produce more bug
as fixes, we will need to find other way to fix it.
here is comment from kernel source which has some more explanation:
* Some buggy high speed devices have bulk endpoints using
* maxpacket sizes other than 512. High speed HCDs may not
* be able to handle that particular bug, so let's warn...
in our case EP3 and EP4 have maxpacket sizes = 64!!!
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
wil6210: let IP stack re-check HW TCP/UDP csum errors
Fix for TCP iperf from Windows to Linux stall after about 1sec
Hardware reports false errors in some situations:
Microsoft IP stack, in violation of RFC 1624, set TCP checksum that should be 0x0
as 0xffff. hardware report Rx csum error. If HW csum absolutely trusted,
this frame can be never received, as re-transmitted one will have same csum problem.
In addition, it mess up block ack reorder buffer, as if packet dropped, it is not score boarded
there.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-beck.git / log