Bjorn Helgaas [Tue, 3 May 2016 16:42:30 +0000 (11:42 -0500)]
Merge branches 'pci/host-armada', 'pci/host-designware', 'pci/host-hv', 'pci/host-imx6', 'pci/host-keystone', 'pci/host-mvebu', 'pci/host-rcar', 'pci/host-thunder' and 'pci/host-vmd' into next
* pci/host-armada:
PCI: armada: Add driver for Marvell Armada 7K/8K PCIe controller
dt-bindings: pci: add DT binding for Marvell Armada 7K/8K PCIe controller
Currently dw_pcie_setup_rc() configures memory base and memory limit in the
type1 configuration header for the root complex. In doing so it uses the
CPU address (pp->mem_base) rather than the bus address (pp->mem_bus_addr).
This is wrong and it is useless since the configuration is overwritten
later on when pci_bus_assign_resources() is called.
Remove this configuration from dw_pcie_setup_rc().
PCI: hv: Report resources release after stopping the bus
Kernel hang is observed when pci-hyperv module is release with device
drivers still attached. E.g., when I do 'rmmod pci_hyperv' with BCM5720
device pass-through-ed (tg3 module) I see the following:
The problem seems to be that we report local resources release before
stopping the bus and removing devices from it and device drivers may try to
perform some operations with these resources on shutdown. Move resources
release report after we do pci_stop_root_bus().
Andrey Smirnov [Mon, 2 May 2016 19:08:21 +0000 (14:08 -0500)]
PCI: imx6: Use enum instead of bool for variant indicator
Use enumerated type instead of a boolean flag to specify the variant of
the PCIe IP block (6Q, 6SX, etc). This patch has zero functional impact,
however it makes the code easier to extend for the case of more than 2
possible variants of an IP block (of which there are).
David Daney [Mon, 11 Apr 2016 23:29:32 +0000 (16:29 -0700)]
PCI: thunder: Don't clobber read-only bits in bridge config registers
The 32-bit addressing modes in the I/O and Prefetchable Memory registers
are required to be read-only. Since the underlying access method allows
them to be set, emulate their read-only nature and always set them.
Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The R-Car PCIe driver requires the use of IRQ domains for its MSI code:
drivers/pci/host/pcie-rcar.c:635:9: error: implicit declaration of function 'irq_find_mapping' [-Werror=implicit-function-declaration]
drivers/pci/host/pcie-rcar.c:666:8: error: implicit declaration of function 'irq_create_mapping' [-Werror=implicit-function-declaration]
...
Add a Kconfig select to ensure that the feature is always enabled.
This is not consistent with what the other drivers do at the moment, but I
have another patch that changes them to do it like this one, which is more
logical.
Thomas Petazzoni [Tue, 26 Apr 2016 08:31:46 +0000 (10:31 +0200)]
PCI: armada: Add driver for Marvell Armada 7K/8K PCIe controller
The Marvell Armada 7K/8K SoCs integrate a PCIe controller from Synopsys.
Add a new driver that provides the small glue needed to use the existing
Designware driver to make it work on Marvell Armada 7K/8K SoCs.
The MSI support will be enabled at a later point.
[bhelgaas: use dev_dbg(), dw_pcie_wait_for_link()] Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/ntb:
PCI: Add DMA alias quirk for mic_x200_dma
PCI: Add support for multiple DMA aliases
PCI: Move informational printk to pci_add_dma_alias()
PCI: Add pci_add_dma_alias() to abstract implementation
* pci/thunderbolt:
thunderbolt: Support 1st gen Light Ridge controller
thunderbolt: Fix typos and magic number
PCI: Add Intel Thunderbolt device IDs
* pci/virtualization:
PCI: Work around Intel Sunrise Point PCH incorrect ACS capability
PCI: Reverse standard ACS vs device-specific ACS enabling
PCI: Mark Intel i40e NIC INTx masking as broken
Fix the misuse of goto statement in ks_pcie_get_irq_controller_info() as
simple return is more appropriate for this function. While at it add an
error log for absence of interrupt controller node.
[bhelgaas: drop "ret" altogether since we always know the return value] Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: Rob Herring <robh+dt@kernel.org> CC: Pawel Moll <pawel.moll@arm.com> CC: Mark Rutland <mark.rutland@arm.com> CC: Ian Campbell <ijc+devicetree@hellion.org.uk> CC: Kumar Gala <galak@codeaurora.org>
Tim Harvey [Wed, 20 Apr 2016 00:52:44 +0000 (19:52 -0500)]
PCI: imx6: Add DT property for link gen, default to Gen1
Freescale has stated [1] that the LVDS clock source of the IMX6 does not
pass the PCI Gen2 clock jitter test, therefore unless an external Gen2
compliant external clock source is present and supplied back to the IMX6
PCIe core via LVDS CLK1/CLK2 you can not claim Gen2 compliance.
Add a DT property to specify Gen1 vs Gen2 and check this before allowing a
Gen2 link.
We default to Gen1 if the property is not present because at this time
there are no IMX6 boards in mainline that 'input' a clock on LVDS
CLK1/CLK2.
In order to be Gen2 compliant on IMX6 you need to:
- Have a Gen2 compliant external clock generator and route that clock back
to either LVDS CLK1 or LVDS CLK2 as an input (see IMX6SX-SabreSD
reference design).
- Specify this clock in the PCIe node in the DT (i.e.,
IMX6QDL_CLK_LVDS1_IN or IMX6QDL_CLK_LVDS2_IN instead of
IMX6QDL_CLK_LVDS1_GATE which configures it as a CLK output).
Petr Štetiar [Wed, 20 Apr 2016 00:42:07 +0000 (19:42 -0500)]
PCI: imx6: Add reset-gpio-active-high boolean property to DT
Currently the reset-gpio DT property which controls the PCI bus device
reset signal defaults to active-low reset sequence (L=reset state,
H=operation state) plus the code in reset function isn't GPIO polarity
aware - it doesn't matter if the defined reset-gpio is active-low or
active-high, it will always result into active-low reset sequence.
I've tried to fix it properly and change the reset-gpio reset sequence to
be polarity-aware, but this patch has been accepted and then reverted as it
has introduced few backward incompatible issues:
1. Some DTBs, for example, imx6qdl-sabresd, don't define reset-gpio
polarity correctly:
reset-gpio = <&gpio7 12 0>;
which means that it's defined as active-high, but in reality it's
active-low; thus it wouldn't work without a DTS fix.
so even if some of the i.MX6 boards had reset-gpio polarity defined
correctly in their DTSes, they would stop working.
As we can't break old DTBs, we can't fix them, so we need to introduce this
new DT reset-gpio-active-high boolean property so we can support boards
with active-high reset sequence.
This active-high reset sequence is for example needed on Apalis SoMs, where
GPIO1_IO28, used to PCIe reset is not connected directly to PERST# PCIe
signal, but it's ORed with RESETBMCU coming off the PMIC, and thus is
inverted, active-high.
Tested-by: Tim Harvey <tharvey@gateworks.com> # Gateworks Ventana boards (which have active-low PERST#) Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Rob Herring <robh@kernel.org>
Adding reset-gpio-active-high boolean DT binding property, which we need to
make PCIe working on Apalis SoMs and not break old DTBs. While at it, I've
fixed comment and GPIO polarity.
On Apalis SoMs the GPIO1_IO28 used to PCIe reset is not connected directly
to PERST# PCIe signal, but it's ORed with RESETBMCU coming off the PMIC,
and thus is inverted, active-high.
Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Christoph Fritz [Tue, 5 Apr 2016 21:53:27 +0000 (16:53 -0500)]
PCI: imx6: Add initial imx6sx support
Add initial PCIe support for the imx6 SoC derivate imx6sx. PCI MSI support
is untested as the necessary suspend/resume quirk is not included in this
patch.
This patch is heavily based on patches by Richard Zhu.
[bhelgaas: factor out refclk enable, fix adjacent typos in imx6q-pcie.txt] Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com> Acked-by: Richard Zhu <Richard.Zhu@freescale.com> Acked-by: Lucas Stach <l.stach@pengutronix.de>
Alex Williamson [Thu, 31 Mar 2016 22:34:37 +0000 (16:34 -0600)]
PCI: Work around Intel Sunrise Point PCH incorrect ACS capability
Intel Sunrise Point root ports implement ACS but use dwords for the
capability and control registers, putting the control register at the wrong
offset.
Use quirks to enable and test ACS for these devices, which match the
standard functions modulo the broken control register offset.
Note that lspci assumes devices implement ACS per spec, so it shows invalid
ACS data for these devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Alex Williamson [Thu, 31 Mar 2016 22:34:32 +0000 (16:34 -0600)]
PCI: Reverse standard ACS vs device-specific ACS enabling
The original thought was that if a device implemented ACS, then surely
we want to use that... well, it turns out that devices can make an ACS
capability so broken that we still need to fall back to quirks.
Reverse the order of ACS enabling to give quirks first shot at it.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Alex Williamson [Thu, 24 Mar 2016 19:03:49 +0000 (13:03 -0600)]
PCI: Mark Intel i40e NIC INTx masking as broken
All of the i40e (XL710/X710) 10/20/40GbE NICs lack support for indicating
INTx is asserted via the interrupt bit in the PCI status register. The
DisINTx bit in the command register is functional, causing these devices to
be incorrectly detected as supporting INTx masking. Quirk them to properly
indicate no INTx masking support.
Device IDs copied from i40e_devids.h.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: John Ronciak <john.ronciak@intel.com> CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
Keystone PCI hardware generates error interrupts at RC using a platform IRQ
instead of a standard MSI or legacy IRQ. Add a simple error handler that
logs the fatal interrupt status to the console.
[bhelgaas: s/node/dev->of_node/, tidy comments, return irqreturn_t directly] Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rob Herring <robh@kernel.org> CC: Pawel Moll <pawel.moll@arm.com> CC: Mark Rutland <mark.rutland@arm.com> CC: Ian Campbell <ijc+devicetree@hellion.org.uk> CC: Kumar Gala <galak@codeaurora.org>
The MIC x200 NTB forwards DMA transactions upstream using multiple alien
RIDs. These RIDs have to be added as aliases to the DMA device to allow
buffer access when the IOMMU is enabled.
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Alex Williamson <alex.williamson@redhat.com> Acked-by: David Woodhouse <David.Woodhouse@intel.com>
x86/PCI: Refine PCI support check in pcibios_init()
Also consider raw_pci_ext_ops when validating if a system has PCI support.
This leads to proper resource allocation via pcibios_resource_survey() in
the case where PCI config space is exclusively accessed through MMCONFIG.
Solve IOMMU support issues with PCIe non-transparent bridges that use
Requester ID look-up tables (RID-LUT), e.g., the PEX8733.
The NTB connects devices in two independent PCI domains. Devices separated
by the NTB are not able to discover each other. A PCI packet being
forwared from one domain to another has to have its RID modified so it
appears on correct bus and completions are forwarded back to the original
domain through the NTB. The RID is translated using a preprogrammed table
(LUT) and the PCI packet propagates upstream away from the NTB. If the
destination system has IOMMU enabled, the packet will be discarded because
the new RID is unknown to the IOMMU. Adding a DMA alias for the new RID
allows IOMMU to properly recognize the packet.
Each device behind the NTB has a unique RID assigned in the RID-LUT. The
current DMA alias implementation supports only a single alias, so it's not
possible to support mutiple devices behind the NTB when IOMMU is enabled.
Enable all possible aliases on a given bus (256) that are stored in a
bitset. Alias devfn is directly translated to a bit number. The bitset is
not allocated for devices that have no need for DMA aliases.
More details can be found in the following article:
http://www.plxtech.com/files/pdf/technical/expresslane/RTC_Enabling%20MulitHostSystemDesigns.pdf
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Alex Williamson <alex.williamson@redhat.com> Acked-by: David Woodhouse <David.Woodhouse@intel.com> Acked-by: Joerg Roedel <jroedel@suse.de>
Bjorn Helgaas [Wed, 24 Feb 2016 19:43:54 +0000 (13:43 -0600)]
PCI: Move informational printk to pci_add_dma_alias()
One of the quirks that adds DMA aliases logs an informational message in
dmesg. Move that to pci_add_dma_alias() so all users log the message
consistently. No functional change intended (except extra message).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Jon Derrick [Fri, 8 Apr 2016 19:44:24 +0000 (14:44 -0500)]
PCI/ACPI: Allow all PCIe services on non-ACPI host bridges
Host bridges we discover via ACPI, i.e., PNP0A03 and PNP0A08 devices, may
have an _OSC method by which the OS can ask the platform for control of
PCIe features like native hotplug, power management events, AER, etc.
Previously, if we found a bridge without an ACPI device, we assumed we did
not have permission to use any of these PCIe features. That seems
unreasonably restrictive.
If we find no ACPI device, assume we can take control of all PCIe features.
The Intel Volume Management Device (VMD) is one such bridge with no ACPI
device. Prior to this change, users had to boot with "pcie_ports=native"
to get hotplug and other services to work below the VMD Root Port.
Light Ridge (CV82524) was the very first copper Thunderbolt controller,
introduced 2010 alongside its fiber-optic cousin Light Peak (CVL2510).
Consequently the chip suffers from some teething troubles:
- MSI is broken for hotplug signaling on the downstream bridges: The chip
just never sends an interrupt. It requests 32 MSIs for each of its six
bridges and the pcieport driver only allocates one per bridge. However
I've verified that even if 32 MSIs are allocated there's no interrupt
on hotplug. The only option is thus to disable MSI, which is also what
OS X does. Apparently all Thunderbolt chips up to revision 1 of Cactus
Ridge 4C are plagued by this issue so quirk those as well.
- The chip supports a maximum hop_count of 32, unlike its successors
which support only 12. Fixup ring_interrupt_active() to cope with
values >= 32.
- Another peculiarity is that the chip supports a maximum of 13 ports
whereas its successors support 12. However the additional port (#5)
seems to be unusable as reading its TB_CFG_PORT config space results in
TB_CFG_ERROR_INVALID_CONFIG_SPACE. Add a quirk to mark the port
disabled on the root switch, assuming that's necessary on all Macs
using this chip.
Tested-by: Lukas Wunner <lukas@wunner.de> [MacBookPro9,1] Tested-by: William Brown <william@blackhats.net.au> [MacBookPro8,2] Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Andreas Noever <andreas.noever@gmail.com>
Lukas Wunner [Sun, 20 Mar 2016 12:57:20 +0000 (13:57 +0100)]
thunderbolt: Fix typos and magic number
Fix typo in tb_cfg_print_error() message. Fix bytecount in struct
tb_drom_entry_port comment. Replace magic number in tb_switch_alloc().
Rename tb_sw_set_unpplugged() and TB_CAL_IECS to fix typos.
[bhelgaas: no functional change intended] Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Andreas Noever <andreas.noever@gmail.com>
Jisheng Zhang [Wed, 16 Mar 2016 09:59:41 +0000 (17:59 +0800)]
PCI: mvebu: Use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS for mvebu_pcie_pm_ops
Use the SET_NOIRQ_SYSTEM_SLEEP_PM_OPS helper macro for mvebu_pcie_pm_ops.
The macro also sets up freeze_noirq, thaw_noirq and poweroff_noirq,
restore_noirq accordingly.
Jisheng Zhang [Wed, 16 Mar 2016 11:40:33 +0000 (19:40 +0800)]
PCI: designware: Move Root Complex setup code to dw_pcie_setup_rc()
dw_pcie_host_init() looks up host bridge resources, ioremaps them, creates
IRQ domains, and enumerates devices below the bridge. dw_pcie_setup_rc()
programs the Root Complex registers. The Root Complex may lose power
during suspend-to-RAM, and when we resume, we want to redo the latter but
not the former.
Move some Root Complex programming from dw_pcie_host_init() to
dw_pcie_setup_rc() where it belongs. DesignWare-based drivers can call
dw_pcie_setup_rc() in their resume paths.
[Niklas Cassel <niklas.cassel@axis.com>: This change moves outbound ATU
programming, which uses pp->mem_base, to dw_pcie_setup_rc(). Apply the
dra7xx pp->mem_base update before calling dw_pcie_setup_rc().]
[bhelgaas: changelog, fold in dra7xx fix from Niklas] Signed-off-by: Jisheng Zhang <jszhang@marvell.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core kernel fixes from Ingo Molnar:
"This contains the nohz/atomic cleanup/fix for the fetch_or() ugliness
you noted during the original nohz pull request, plus there's also
misc fixes:
- fix liblockdep build bug
- fix uapi header build bug
- print more lockdep hash collision info to help debug recent reports
of hash collisions
- update MAINTAINERS email address"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS: Update my email address
locking/lockdep: Print chain_key collision information
uapi/linux/stddef.h: Provide __always_inline to userspace headers
tools/lib/lockdep: Fix unsupported 'basename -s' in run_tests.sh
locking/atomic, sched: Unexport fetch_or()
timers/nohz: Convert tick dependency mask to atomic_t
locking/atomic: Introduce atomic_fetch_or()
Commit 840f5b0572ea ("media: au0828 disable tuner to demod link in
au0828_media_device_register()") removed all uses of the 'dtv_demod',
but left the variable itself around.
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"This lot contains:
- Some fixups for the fallout of the topology consolidation which
unearthed AMD/Intel inconsistencies
- Documentation for the x86 topology management
- Support for AMD advanced power management bits
- Two simple cleanups removing duplicated code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Add advanced power management bits
x86/thread_info: Merge two !__ASSEMBLY__ sections
x86/cpufreq: Remove duplicated TDP MSR macro definitions
x86/Documentation: Start documenting x86 topology
x86/cpu: Get rid of compute_unit_id
perf/x86/amd: Cleanup Fam10h NB event constraints
x86/topology: Fix AMD core count
Merge tag 'rproc-v4.6-rc1' of git://github.com/andersson/remoteproc
Pull remoteproc fix from Bjorn Andersson:
"Fix incorrect error check in the ST remoteproc driver and advertise
the newly created linux-remoteproc mailing list"
* tag 'rproc-v4.6-rc1' of git://github.com/andersson/remoteproc:
MAINTAINERS: Add mailing list for remote processor subsystems
remoteproc: st: fix check of syscon_regmap_lookup_by_phandle() return value
Pull SCSI target fixes from Nicholas Bellinger:
"This includes fixes from HCH for -rc1 configfs default_groups
conversion changes that ended up breaking some iscsi-target
default_groups, along with Sagi's ib_drain_qp() conversion for
iser-target to use the common caller now available to RDMA kernel
consumers in v4.6+ code"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: add a new add_wwn_groups fabrics method
target: initialize the nacl base CIT begfore init_nodeacl
target: remove ->fabric_cleanup_nodeacl
iser-target: Use ib_drain_qp
Convert straggling drivers to new six-argument get_user_pages()
Commit d4edcf0d5695 ("mm/gup: Switch all callers of get_user_pages() to
not pass tsk/mm") switched get_user_pages() callers to the simpler model
where they no longer pass in the thread and mm pointer. But since then
we've merged changes to a few drivers that re-introduce use of the old
interface. Let's fix them up.
They continued to work fine (thanks to the truly disgusting macros
introduced in commit cde70140fed8: "mm/gup: Overload get_user_pages()
functions"), but cause unnecessary build noise.
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of const updates for reset ops and a couple fixes to the
newly introduced IPQ4019 clock driver"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: ipq4019: add some fixed clocks for ddrppl and fepll
clk: qcom: ipq4019: switch remaining defines to enums
clk: qcom: Make reset_control_ops const
clk: tegra: Make reset_control_ops const
clk: sunxi: Make reset_control_ops const
clk: atlas7: Make reset_control_ops const
clk: rockchip: Make reset_control_ops const
clk: mmp: Make reset_control_ops const
clk: mediatek: Make reset_control_ops const
Merge tag 'pm+acpi-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fix from Rafael J. Wysocki:
"Just one fix for a nasty boot failure on some systems based on Intel
Skylake that shipped with broken firmware where enabling
hardware-coordinated P-states management (HWP) causes a faulty
interrupt handler in SMM to be invoked and crash the system (Srinivas
Pandruvada)"
* tag 'pm+acpi-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / processor: Request native thermal interrupt handling via _OSC
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
.mailmap: add Christophe Ricard
Make CONFIG_FHANDLE default y
mm/page_isolation.c: fix the function comments
oom, oom_reaper: do not enqueue task if it is on the oom_reaper_list head
mm/page_isolation: fix tracepoint to mirror check function behavior
mm/rmap: batched invalidations should use existing api
x86/mm: TLB_REMOTE_SEND_IPI should count pages
mm: fix invalid node in alloc_migrate_target()
include/linux/huge_mm.h: return NULL instead of false for pmd_trans_huge_lock()
mm, kasan: fix compilation for CONFIG_SLAB
MAINTAINERS: orangefs mailing list is subscribers-only
Merge branch 'for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This has a few fixes Dave Sterba had queued up. These are all pretty
small, but since they were tested I decided against waiting for more"
* 'for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: transaction_kthread() is not freezable
btrfs: cleaner_kthread() doesn't need explicit freeze
btrfs: do not write corrupted metadata blocks to disk
btrfs: csum_tree_block: return proper errno value
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- fix oops when patching in alternative sequences on big-endian CPUs
- reconcile asm/perf_event.h after merge window fallout with KVM ARM
- defconfig updates
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: updates for 4.6
arm64: perf: Move PMU register related defines to asm/perf_event.h
arm64: opcodes.h: Add arm big-endian config options before including arm header
Merge tag 'sound-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes:
- a fix in ALSA timer core to avoid possible BUG() trigger
- a fix in ALSA timer core 32bit compat layer
- a few HD-audio quirks for ASUS and HP machines
- AMD HD-audio HDMI controller quirks
- fixes of USB-audio double-free at some error paths
- a fix for memory leak in DICE driver at hotunplug"
* tag 'sound-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: timer: Use mod_timer() for rearming the system timer
ALSA: hda - fix front mic problem for a HP desktop
ALSA: usb-audio: Fix double-free in error paths after snd_usb_add_audio_stream() call
ALSA: hda: add AMD Polaris-10/11 AZ PCI IDs with proper driver caps
ALSA: dice: fix memory leak when unplugging
ALSA: hda - Apply fix for white noise on Asus N550JV, too
ALSA: hda - Fix white noise on Asus N750JV headphone
ALSA: hda - Asus N750JV external subwoofer fixup
ALSA: timer: fix gparams ioctl compatibility for different architectures
Newer Fedora and OpenSUSE didn't boot with my standard configuration.
It took me some time to figure out why, in fact I had to write a script
to try different config options systematically.
The problem is that something (systemd) in dracut depends on
CONFIG_FHANDLE, which adds open by file handle syscalls.
While it is set in defconfigs it is very easy to miss when updating
older configs because it is not default y.
Make it default y and also depend on EXPERT, as dracut use is likely
widespread.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Cc: Richard Weinberger <richard.weinberger@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Neil Zhang [Fri, 1 Apr 2016 21:31:37 +0000 (14:31 -0700)]
mm/page_isolation.c: fix the function comments
Commit fea85cff11de ("mm/page_isolation.c: return last tested pfn rather
than failure indicator") changed the meaning of the return value. Let's
change the function comments as well.
Signed-off-by: Neil Zhang <neilzhang1123@hotmail.com> Cc: Joonsoo Kim <js1304@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 1 Apr 2016 21:31:34 +0000 (14:31 -0700)]
oom, oom_reaper: do not enqueue task if it is on the oom_reaper_list head
Commit bb29902a7515 ("oom, oom_reaper: protect oom_reaper_list using
simpler way") has simplified the check for tasks already enqueued for
the oom reaper by checking tsk->oom_reaper_list != NULL. This check is
not sufficient because the tsk might be the head of the queue without
any other tasks queued and then we would simply lockup looping on the
same task. Fix the condition by checking for the head as well.
Fixes: bb29902a7515 ("oom, oom_reaper: protect oom_reaper_list using simpler way") Signed-off-by: Michal Hocko <mhocko@suse.com> Acked-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lucas Stach [Fri, 1 Apr 2016 21:31:32 +0000 (14:31 -0700)]
mm/page_isolation: fix tracepoint to mirror check function behavior
Page isolation has not failed if the fin pfn extends beyond the end pfn
and test_pages_isolated checks this correctly. Fix the tracepoint to
report the same result as the actual check function.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Joonsoo Kim <js1304@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nadav Amit [Fri, 1 Apr 2016 21:31:26 +0000 (14:31 -0700)]
mm/rmap: batched invalidations should use existing api
The recently introduced batched invalidations mechanism uses its own
mechanism for shootdown. However, it does wrong accounting of
interrupts (e.g., inc_irq_stat is called for local invalidations),
trace-points (e.g., TLB_REMOTE_SHOOTDOWN for local invalidations) and
may break some platforms as it bypasses the invalidation mechanisms of
Xen and SGI UV.
This patch reuses the existing TLB flushing mechnaisms instead. We use
NULL as mm to indicate a global invalidation is required.
Fixes 72b252aed506b8 ("mm: send one IPI per CPU to TLB flush all entries after unmapping pages") Signed-off-by: Nadav Amit <namit@vmware.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Rik van Riel <riel@redhat.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nadav Amit [Fri, 1 Apr 2016 21:31:23 +0000 (14:31 -0700)]
x86/mm: TLB_REMOTE_SEND_IPI should count pages
TLB_REMOTE_SEND_IPI was recently introduced, but it counts bytes instead
of pages. In addition, it does not report correctly the case in which
flush_tlb_page flushes a page. Fix it to be consistent with other TLB
counters.
Fixes: 5b74283ab251b9d ("x86, mm: trace when an IPI is about to be sent") Signed-off-by: Nadav Amit <namit@vmware.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Rik van Riel <riel@redhat.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is incorrect to use next_node to find a target node, it will return
MAX_NUMNODES or invalid node. This will lead to crash in buddy system
allocation.
Marcin Wojtas [Fri, 1 Apr 2016 13:21:18 +0000 (15:21 +0200)]
net: mvneta: fix changing MTU when using per-cpu processing
After enabling per-cpu processing it appeared that under heavy load
changing MTU can result in blocking all port's interrupts and
transmitting data is not possible after the change.
This commit fixes above issue by disabling percpu interrupts for the
time, when TXQs and RXQs are reconfigured.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Initially the phy_bus_name was added to manipulate the
driver name but it was recently just used to manage the
fixed-link and then to take some decision at run-time.
So the patch uses the is_pseudo_fixed_link and removes
the phy_bus_name variable not necessary anymore.
The driver can manage the mdio registration by using phy-handle,
dwmac-mdio and own parameter e.g. snps,phy-addr.
This patch takes care about all these possible configurations
and fixes the mdio registration in case of there is a real
transceiver or a switch (that needs to be managed by using
fixed-link).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Reviewed-by: Andreas Färber <afaerber@suse.de> Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com> Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org> Cc: Dinh Nguyen <dinh.linux@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: Phil Reid <preid@electromag.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Revert "stmmac: Fix 'eth0: No PHY found' regression"
This reverts commit 88f8b1bb41c6208f81b6a480244533ded7b59493.
due to problems on GeekBox and Banana Pi M1 board when
connected to a real transceiver instead of a switch via
fixed-link.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org> Cc: Andreas Färber <afaerber@suse.de> Cc: Frank Schäfer <fschaefer.oss@googlemail.com> Cc: Dinh Nguyen <dinh.linux@gmail.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixs a regression raised when test on chips that use
the normal descriptor layout. In fact, no len bits were set for
the TDES1 and no OWN bit inside the TDES0.
Signed-off-by: Giuseppe CAVALLARO <peppe.cavallaro@st.com> Tested-by: Andreas Färber <afaerber@suse.de> Cc: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Same can be triggered with PROVE_RCU (+ PROVE_RCU_REPEATEDLY) enabled
from tun_attach_filter() when user space calls ioctl(tun_fd, TUN{ATTACH,
DETACH}FILTER, ...) for adding/removing a BPF filter on tap devices.
Since the fix in f91ff5b9ff52 ("net: sk_{detach|attach}_filter() rcu
fixes") sk_attach_filter()/sk_detach_filter() now dereferences the
filter with rcu_dereference_protected(), checking whether socket lock
is held in control path.
Since its introduction in 994051625981 ("tun: socket filter support"),
tap filters are managed under RTNL lock from __tun_chr_ioctl(). Thus the
sock_owned_by_user(sk) doesn't apply in this specific case and therefore
triggers the false positive.
Extend the BPF API with __sk_attach_filter()/__sk_detach_filter() pair
that is used by tap filters and pass in lockdep_rtnl_is_held() for the
rcu_dereference_protected() checks instead.
Reported-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nothing too crazy in here: a bunch of AMD fixes/quirks, two msm fixes,
some rockchip fixes, and a udl warning fix, along with one locking fix
for displayport that seems to fix some dodgy monitors"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/udl: Use unlocked gem unreferencing
drm/dp: move hw_mutex up the call stack
drm/amdgpu: Don't move pinned BOs
drm/radeon: Don't move pinned BOs
drm/radeon: add a dpm quirk for all R7 370 parts
drm/radeon: add another R7 370 quirk
drm/rockchip: dw_hdmi: Don't call platform_set_drvdata()
drm/rockchip: vop: Fix vop crtc cleanup
drm/rockchip: dw_hdmi: Call drm_encoder_cleanup() in error path
drm/rockchip: vop: Disable planes when disabling CRTC
drm/rockchip: vop: Don't reject empty modesets
drm/rockchip: cancel pending vblanks on close
drm/rockchip: vop: fix crtc size in plane check
drm/radeon: add a dpm quirk for sapphire Dual-X R7 370 2G D5
drm/amd: Beef up ACP Kconfig menu text
drm/msm: fix typo in the !COMMON_CLK case
drm/msm: fix bug after preclose removal
Merge tag 'powerpc-4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fixup preempt underflow with huge pages from Sebastian Siewior
- Fix altivec SPR not being saved from Oliver O'Halloran
- Correct used_vsr comment from Simon Guo
* tag 'powerpc-4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Correct used_vsr comment
powerpc/process: Fix altivec SPR not being saved
powerpc/mm: Fixup preempt underflow with huge pages
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
- A proper fix for the locking issue in the dasd driver
- Wire up the new preadv2 nad pwritev2 system calls
- Add the mark_rodata_ro function and set DEBUG_RODATA=y
- A few more bug fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: wire up preadv2/pwritev2 syscalls
s390/pci: PCI function group 0 is valid for clp_query_pci_fn
s390/crypto: provide correct file mode at device register.
s390/mm: handle PTE-mapped tail pages in fast gup
s390: add DEBUG_RODATA support
s390: disable postinit-readonly for now
s390/dasd: reorder lcu and device lock
s390/cpum_sf: Fix cpu hotplug notifier transitions
s390/cpum_cf: Fix missing cpu hotplug notifier transition
ALSA: timer: Use mod_timer() for rearming the system timer
ALSA system timer backend stops the timer via del_timer() without sync
and leaves del_timer_sync() at the close instead. This is because of
the restriction by the design of ALSA timer: namely, the stop callback
may be called from the timer handler, and calling the sync shall lead
to a hangup. However, this also triggers a kernel BUG() when the
timer is rearmed immediately after stopping without sync:
kernel BUG at kernel/time/timer.c:966!
Call Trace:
<IRQ>
[<ffffffff8239c94e>] snd_timer_s_start+0x13e/0x1a0
[<ffffffff8239e1f4>] snd_timer_interrupt+0x504/0xec0
[<ffffffff8122fca0>] ? debug_check_no_locks_freed+0x290/0x290
[<ffffffff8239ec64>] snd_timer_s_function+0xb4/0x120
[<ffffffff81296b72>] call_timer_fn+0x162/0x520
[<ffffffff81296add>] ? call_timer_fn+0xcd/0x520
[<ffffffff8239ebb0>] ? snd_timer_interrupt+0xec0/0xec0
....
It's the place where add_timer() checks the pending timer. It's clear
that this may happen after the immediate restart without sync in our
cases.
So, the workaround here is just to use mod_timer() instead of
add_timer(). This looks like a band-aid fix, but it's a right move,
as snd_timer_interrupt() takes care of the continuous rearm of timer.
Pierre Morel [Wed, 16 Mar 2016 12:56:35 +0000 (13:56 +0100)]
s390/pci: PCI function group 0 is valid for clp_query_pci_fn
The PCI function group 0 is a valid function group,
it is wrong to reject it.
Let's accept PCI function group 0.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com> Acked-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Daniel Vetter [Wed, 30 Mar 2016 09:40:43 +0000 (11:40 +0200)]
drm/udl: Use unlocked gem unreferencing
For drm_gem_object_unreference callers are required to hold
dev->struct_mutex, which these paths don't. Enforcing this requirement
has become a bit more strict with
Rob Clark [Thu, 25 Feb 2016 21:15:05 +0000 (16:15 -0500)]
drm/dp: move hw_mutex up the call stack
1) don't let other threads trying to bang on aux channel interrupt the
defer timeout/logic
2) don't let other threads interrupt the i2c over aux logic
Technically, according to people who actually have the DP spec, this
should not be required. In practice, it makes some troublesome Dell
monitor (and perhaps others) work, so probably a case of "It's compliant
if it works with windows" on the hw vendor's part..
v2: rebased to come before DPCD/AUX logging patch for easier backport
to stable branches.
Reported-by: Dave Wysochanski <dwysocha@redhat.com>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1274157 Cc: stable@vger.kernel.org Signed-off-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 1 Apr 2016 03:14:10 +0000 (13:14 +1000)]
Merge branch 'msm-fixes-4.6-rc1' of git://people.freedesktop.org/~robclark/linux into drm-fixes
two minor msm fixes.
* 'msm-fixes-4.6-rc1' of git://people.freedesktop.org/~robclark/linux:
drm/msm: fix typo in the !COMMON_CLK case
drm/msm: fix bug after preclose removal
Dave Airlie [Fri, 1 Apr 2016 03:13:34 +0000 (13:13 +1000)]
Merge branch 'drm-next-4.6' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Just a few fixes for 4.6 this week:
- Add some SI DPM quirks
- Improve the ACP Kconfig text
- Additional BO pinning checks
* 'drm-next-4.6' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Don't move pinned BOs
drm/radeon: Don't move pinned BOs
drm/radeon: add a dpm quirk for all R7 370 parts
drm/radeon: add another R7 370 quirk
drm/radeon: add a dpm quirk for sapphire Dual-X R7 370 2G D5
drm/amd: Beef up ACP Kconfig menu text
Nicolas Dichtel [Thu, 31 Mar 2016 16:10:31 +0000 (18:10 +0200)]
rtnl: fix msg size calculation in if_nlmsg_size()
Size of the attribute IFLA_PHYS_PORT_NAME was missing.
Fixes: db24a9044ee1 ("net: add support for phys_port_name") CC: David Ahern <dsahern@gmail.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jisheng Zhang [Wed, 30 Mar 2016 11:55:21 +0000 (19:55 +0800)]
net: mvneta: replace MVNETA_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
The mvneta is also used in some Marvell berlin family SoCs which may
have 64bytes cacheline size. Replace the MVNETA_CPU_D_CACHE_LINE_SIZE
usage with L1_CACHE_BYTES.
And since dma_alloc_coherent() is always cacheline size aligned, so
remove the align checks.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the vendor-specific bootloaders set up this part
of the initialization for us, so this was never added.
However, since upstream bootloaders don't initialize the
chip specifically, they leave the fiber MII's PDOWN flag
set, which means that the CPU port doesn't connect.
This patch checks whether this flag has been clear prior
by something else, and if not make us clear it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Patrick Uiterwijk <patrick@puiterwijk.org> Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add versions of the phy_page_read and _write functions to
be used in a context where the SMI mutex is held.
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: Patrick Uiterwijk <patrick@puiterwijk.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladis Dronov [Thu, 31 Mar 2016 16:05:43 +0000 (12:05 -0400)]
ALSA: usb-audio: Fix double-free in error paths after snd_usb_add_audio_stream() call
create_fixed_stream_quirk(), snd_usb_parse_audio_interface() and
create_uaxx_quirk() functions allocate the audioformat object by themselves
and free it upon error before returning. However, once the object is linked
to a stream, it's freed again in snd_usb_audio_pcm_free(), thus it'll be
double-freed, eventually resulting in a memory corruption.
This patch fixes these failures in the error paths by unlinking the audioformat
object before freeing it.
Based on a patch by Takashi Iwai <tiwai@suse.de>
[Note for stable backports:
this patch requires the commit 902eb7fd1e4a ('ALSA: usb-audio: Minor
code cleanup in create_fixed_stream_quirk()')]
This was quite an oversight. After a readdir, the module could not be
unloaded, the number of slots is wrong, and memory near the slot bitmap
is possibly corrupt. Oops.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
David S. Miller [Thu, 31 Mar 2016 15:40:16 +0000 (11:40 -0400)]
Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2016-03-29
This series contains fixes to ixgbe and ixgbevf.
Tushar fixes an issue which was introduced with an earlier commit, where
hardware register RAR0 default MAC address does not get set properly.
Alex fixes two issues, first being the VXLAN port number should be stored
in network order instead of in host order. The second fix corrects the ATR
code to handle IPv6 extension headers. The issue was ATR code was assuming
that it would be able to use tcp_hdr for every TCP frame that came through,
but that is not the case, which resulted in bad filters being setup.
Mark fixes a use of usleep_range() to udelay() in the case where a lock
is being held.
Stefan fixes the offline self tests where ndo_stop() should be used instead
of ndo_close(), which causes IFF_UP to be cleared and interface routes get
removed.
Emil fixes the error case where we need to return an error when a MAC
address change is rejected by the PF. This helps prevent the user from
modifying the MAC address when the operation is not permitted.
Sridhar provides three fixes for ixgbe, all dealing with traffic class
offload handling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log