This is on a system with 8TB available via the AMS pool, and as a quirk
of AMS in firmware, all of that memory shows up in node 0. So, we end
up with an allocation that will fail the goal/limit constraints.
In theory, we could "fall-back" to alloc_bootmem_node() in
sparse_early_usemaps_alloc_node(), but since we actually have HOTREMOVE
defined, we'll BUG_ON() instead. A simple solution appears to be to
unconditionally remove the limit condition in alloc_bootmem_section,
meaning allocations are allowed to cross section boundaries (necessary
for systems of this size).
Johannes Weiner pointed out that if alloc_bootmem_section() no longer
guarantees section-locality, we need check_usemap_section_nr() to print
possible cross-dependencies between node descriptors and the usemaps
allocated through it. That makes the two loops in
sparse_early_usemaps_alloc_node() identical, so re-factor the code a
bit.
[akpm@linux-foundation.org: code simplification] Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com> Cc: Dave Hansen <haveblue@us.ibm.com> Cc: Anton Blanchard <anton@au1.ibm.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Ben Herrenschmidt <benh@kernel.crashing.org> Cc: Robert Jennings <rcj@linux.vnet.ibm.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Mel Gorman <mgorman@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some cases it may happen that pmd_none_or_clear_bad() is called with
the mmap_sem hold in read mode. In those cases the huge page faults can
allocate hugepmds under pmd_none_or_clear_bad() and that can trigger a
false positive from pmd_bad() that will not like to see a pmd
materializing as trans huge.
It's not khugepaged causing the problem, khugepaged holds the mmap_sem
in write mode (and all those sites must hold the mmap_sem in read mode
to prevent pagetables to go away from under them, during code review it
seems vm86 mode on 32bit kernels requires that too unless it's
restricted to 1 thread per process or UP builds). The race is only with
the huge pagefaults that can convert a pmd_none() into a
pmd_trans_huge().
Effectively all these pmd_none_or_clear_bad() sites running with
mmap_sem in read mode are somewhat speculative with the page faults, and
the result is always undefined when they run simultaneously. This is
probably why it wasn't common to run into this. For example if the
madvise(MADV_DONTNEED) runs zap_page_range() shortly before the page
fault, the hugepage will not be zapped, if the page fault runs first it
will be zapped.
Altering pmd_bad() not to error out if it finds hugepmds won't be enough
to fix this, because zap_pmd_range would then proceed to call
zap_pte_range (which would be incorrect if the pmd become a
pmd_trans_huge()).
The simplest way to fix this is to read the pmd in the local stack
(regardless of what we read, no need of actual CPU barriers, only
compiler barrier needed), and be sure it is not changing under the code
that computes its value. Even if the real pmd is changing under the
value we hold on the stack, we don't care. If we actually end up in
zap_pte_range it means the pmd was not none already and it was not huge,
and it can't become huge from under us (khugepaged locking explained
above).
All we need is to enforce that there is no way anymore that in a code
path like below, pmd_trans_huge can be false, but pmd_none_or_clear_bad
can run into a hugepmd. The overhead of a barrier() is just a compiler
tweak and should not be measurable (I only added it for THP builds). I
don't exclude different compiler versions may have prevented the race
too by caching the value of *pmd on the stack (that hasn't been
verified, but it wouldn't be impossible considering
pmd_none_or_clear_bad, pmd_bad, pmd_trans_huge, pmd_none are all inlines
and there's no external function called in between pmd_trans_huge and
pmd_none_or_clear_bad).
if (pmd_trans_huge(*pmd)) {
if (next-addr != HPAGE_PMD_SIZE) {
VM_BUG_ON(!rwsem_is_locked(&tlb->mm->mmap_sem));
split_huge_page_pmd(vma->vm_mm, pmd);
} else if (zap_huge_pmd(tlb, vma, pmd, addr))
continue;
/* fall through */
}
if (pmd_none_or_clear_bad(pmd))
Because this race condition could be exercised without special
privileges this was reported in CVE-2012-1179.
The race was identified and fully explained by Ulrich who debugged it.
I'm quoting his accurate explanation below, for reference.
After the PMD table entry has been cleared, there is an inconsistency
between the actual number of PMD table entries that are mapping the page
and the page's map count (_mapcount field in struct page). When the page
is subsequently reclaimed, __split_huge_page() detects this inconsistency.
The root cause of the problem is a race of two threads in a multithreaded
process. Thread B incurs a page fault on a virtual address that has never
been accessed (PMD entry is zero) while Thread A is executing an madvise()
system call on a virtual address within the same 2 MB (huge page) range.
- Thread A is executing an madvise(..., MADV_DONTNEED) system call
on the virtual address range "A(range)" shown in the picture.
sys_madvise
// Acquire the semaphore in shared mode.
down_read(¤t->mm->mmap_sem)
...
madvise_vma
switch (behavior)
case MADV_DONTNEED:
madvise_dontneed
zap_page_range
unmap_vmas
unmap_page_range
zap_pud_range
zap_pmd_range
//
// Assume that this huge page has never been accessed.
// I.e. content of the PMD entry is zero (not mapped).
//
if (pmd_trans_huge(*pmd)) {
// We don't get here due to the above assumption.
}
//
// Assume that Thread B incurred a page fault and
.---------> // sneaks in here as shown below.
| //
| if (pmd_none_or_clear_bad(pmd))
| {
| if (unlikely(pmd_bad(*pmd)))
| pmd_clear_bad
| {
| pmd_ERROR
| // Log "bad pmd ..." message here.
| pmd_clear
| // Clear the page's PMD entry.
| // Thread B incremented the map count
| // in page_add_new_anon_rmap(), but
| // now the page is no longer mapped
| // by a PMD entry (-> inconsistency).
| }
| }
|
v
- Thread B is handling a page fault on virtual address "B(fault)" shown
in the picture.
...
do_page_fault
__do_page_fault
// Acquire the semaphore in shared mode.
down_read_trylock(&mm->mmap_sem)
...
handle_mm_fault
if (pmd_none(*pmd) && transparent_hugepage_enabled(vma))
// We get here due to the above assumption (PMD entry is zero).
do_huge_pmd_anonymous_page
alloc_hugepage_vma
// Allocate a new transparent huge page here.
...
__do_huge_pmd_anonymous_page
...
spin_lock(&mm->page_table_lock)
...
page_add_new_anon_rmap
// Here we increment the page's map count (starts at -1).
atomic_set(&page->_mapcount, 0)
set_pmd_at
// Here we set the page's PMD entry which will be cleared
// when Thread A calls pmd_clear_bad().
...
spin_unlock(&mm->page_table_lock)
The mmap_sem does not prevent the race because both threads are acquiring
it in shared mode (down_read). Thread B holds the page_table_lock while
the page's map count and PMD table entry are updated. However, Thread A
does not synchronize on that lock.
====== end quote =======
[akpm@linux-foundation.org: checkpatch fixes] Reported-by: Ulrich Obergfell <uobergfe@redhat.com> Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Mel Gorman <mgorman@suse.de> Cc: Hugh Dickins <hughd@google.com> Cc: Dave Jones <davej@redhat.com> Acked-by: Larry Woodman <lwoodman@redhat.com> Acked-by: Rik van Riel <riel@redhat.com> Cc: Mark Salter <msalter@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the recent changes to clear_IO_APIC_pin() which tries to
clear remoteIRR bit explicitly, some of the users started to see
"Unable to reset IRR for apic .." messages.
Close look shows that these are related to bogus IO-APIC entries
which return's all 1's for their io-apic registers. And the
above mentioned error messages are benign. But kernel should
have ignored such io-apic's in the first place.
Check if register 0, 1, 2 of the listed io-apic are all 1's and
ignore such io-apic.
Reported-by: Álvaro Castillo <midgoon@gmail.com> Tested-by: Jon Dufresne <jon@jondufresne.org> Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Cc: yinghai@kernel.org Cc: kernel-team@fedoraproject.org Cc: Josh Boyer <jwboyer@redhat.com> Link: http://lkml.kernel.org/r/1331577393.31585.94.camel@sbsiddha-desk.sc.intel.com
[ Performed minor cleanup of affected code. ] Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An iser target may send iscsi NO-OP PDUs as soon as it marks the iSER
iSCSI session as fully operative. This means that there is window
where there are no posted receive buffers on the initiator side, so
it's possible for the iSER RC connection to break because of RNR NAK /
retry errors. To fix this, rely on the flags bits in the login
request to have FFP (0x3) in the lower nibble as a marker for the
final login request, and post an initial chunk of receive buffers
before sending that login request instead of after getting the login
response.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes it possible to reload driver if insmod has failed due to
missing firmware.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the RTC code does not disable the alarm in the hardware.
This means that after a sequence such as the one below (the files are in the
RTC sysfs), the box will boot up after 2 minutes even though we've
asked for the alarm to be turned off.
Fix this by disabling the alarm when there are no timers to run.
The original version of this patch was reverted. This version
disables the irq directly instead of setting a disabled timer
in the future.
Cc: John Stultz <john.stultz@linaro.org> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
[Merged in the second revision from Rabin] Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 2008, commit 0c5d1eb77a8be ("genirq: record trigger type") modified the
way set_irq_type() handles the 'no trigger' condition. However, this has
an adverse effect on PCMCIA support on Intel StrongARM and probably PXA
platforms.
PCMCIA has several status signals on the socket which can trigger
interrupts; some of these status signals depend on the card's mode
(whether it is configured in memory or IO mode). For example, cards have
a 'Ready/IRQ' signal: in memory mode, this provides an indication to
PCMCIA that the card has finished its power up initialization. In IO
mode, it provides the device interrupt signal. Other status signals
switch between on-board battery status and loud speaker output.
In classical PCMCIA implementations, where you have a specific socket
controller, the controller provides a method to mask interrupts from the
socket, and importantly ignore any state transitions on the pins which
correspond with interrupts once masked. This masking prevents unwanted
events caused by the removal and application of socket power being
forwarded.
However, on platforms where there is no socket controller, the PCMCIA
status and interrupt signals are routed to standard edge-triggered GPIOs.
These GPIOs can be configured to interrupt on rising edge, falling edge,
or never. This is where the problems start.
Edge triggered interrupts are required to record events while disabled via
the usual methods of {free,request,disable,enable}_irq() to prevent
problems with dropped interrupts (eg, the 8390 driver uses disable_irq()
to defer the delivery of interrupts). As a result, these interfaces can
not be used to implement the desired behaviour.
The side effect of this is that if the 'Ready/IRQ' GPIO is disabled via
disable_irq() on suspend, and enabled via enable_irq() after resume, we
will record the state transitions caused by powering events as valid
interrupts, and foward them to the card driver, which may attempt to
access a card which is not powered up.
This leads delays resume while drivers spin in their interrupt handlers,
and complaints from drivers before they realize what's happened.
Moreover, in the case of the 'Ready/IRQ' signal, this is requested and
freed by the card driver itself; the PCMCIA core has no idea whether the
interrupt is requested, and, therefore, whether a call to disable_irq()
would be valid. (We tried this around 2.4.17 / 2.5.1 kernel era, and
ended up throwing it out because of this problem.)
Therefore, it was decided back in around 2002 to disable the edge
triggering instead, resulting in all state transitions on the GPIO being
ignored. That's what we actually need the hardware to do.
The commit above changes this behaviour; it explicitly prevents the 'no
trigger' state being selected.
The reason that request_irq() does not accept the 'no trigger' state is
for compatibility with existing drivers which do not provide their desired
triggering configuration. The set_irq_type() function is 'new' and not
used by non-trigger aware drivers.
Therefore, revert this change, and restore previously working platforms
back to their former state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Cc: linux@arm.linux.org.uk Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The queue handling in the udev daemon assumes that the events are
ordered.
Before this patch uevent_seqnum is incremented under sequence_lock,
than an event is send uner uevent_sock_mutex. I want to say that code
contained a window between incrementing seqnum and sending an event.
This patch locks uevent_sock_mutex before incrementing uevent_seqnum.
v2: delete sequence_lock, uevent_seqnum is protected by uevent_sock_mutex
v3: unlock the mutex before the goto exit
Thanks for Kay for the comments.
Signed-off-by: Andrew Vagin <avagin@openvz.org> Tested-By: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'long secs' is passed as divisor to div_s64, which accepts a 32bit
divisor. On 64bit machines that value is trimmed back from 8 bytes
back to 4, causing a divide by zero when the number is bigger than
(1 << 32) - 1 and all 32 lower bits are 0.
Driver rtl8192ce when used with the RTL8188CE device would start at about
20 Mbps on a 54 Mbps connection, but quickly drop to 1 Mbps. One of the
symptoms is that the AP would need to retransmit each packet 4 of 5 times
before the driver would acknowledge it. Recovery is possible only by
unloading and reloading the driver. This problem was reported at
https://bugzilla.redhat.com/show_bug.cgi?id=770207.
The problem is due to a missing update of the gain setting.
Signed-off-by: Jingjun Wu <jingjun_wu@realsil.com.cn> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When driver rtl8192cu is used with the debug level set to 3 or greater,
the result is "sleeping function called from invalid context" due to
an rcu_read_lock() call in the DM refresh routine in driver rtl8192c.
This lock is not necessary as the USB driver does not use the struct
being protected, thus the lock is set only when a PCI interface is
active.
This bug is reported in https://bugzilla.kernel.org/show_bug.cgi?id=42775.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com> Tested-by: Ronald Wahl <ronald.wahl@raritan.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Ronald Wahl <ronald.wahl@raritan.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle previous allocation failures when freeing device memory
Signed-off-by: Simon Graham <simon.graham@virtualcomputer.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Mikhail Kryshen <mikhail@kryshen.net> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A MCS7820 device supports two serial ports and a MCS7840 device supports
four serial ports. Both devices use the same driver, but the attach function
in driver was unable to correctly handle the port numbers for MCS7820
device. This problem has been fixed in this patch and this fix has been
verified on x86 Linux kernel 3.2.9 with both MCS7820 and MCS7840 devices.
Signed-off-by: Donald Lee <donald@asix.com.tw> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates the cp210x driver to support CP210x multiple
interface devices devices from Silicon Labs. The existing driver
always sends control requests to interface 0, which is hardcoded in
the usb_control_msg function calls. This only allows for single
interface devices to be used, and causes a bug when using ports on an
interface other than 0 in the multiple interface devices.
Here are the changes included in this patch:
- Updated the device list to contain the Silicon Labs factory default
VID/PID for multiple interface CP210x devices
- Created a cp210x_port_private struct created for each port on
startup, this struct holds the interface number
- Added a cp210x_release function to clean up the cp210x_port_private
memory created on startup
- Modified usb_get_config and usb_set_config to get a pointer to the
cp210x_port_private struct, and use the interface number there in the
usb_control_message wIndex param
Signed-off-by: Preston Fick <preston.fick@silabs.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gobi 1000 devices have a different port layout, which wasn't respected
by the current driver, and thus it grabbed the QMI/net port. In the
near future we'll be attaching another driver to the QMI/net port for
these devices (cdc-wdm and qmi_wwan) so make sure the qcserial driver
doesn't claim them. This patch also prevents qcserial from binding to
interfaces 0 and 1 on 1K devices because those interfaces do not
respond.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When build i.mx platform with imx_v6_v7_defconfig, and after adding
USB Gadget support, it has below build error:
CC drivers/usb/host/fsl-mph-dr-of.o
drivers/usb/host/fsl-mph-dr-of.c: In function 'fsl_usb2_device_register':
drivers/usb/host/fsl-mph-dr-of.c:97: error: 'struct pdev_archdata'
has no member named 'dma_mask'
It has discussed at: http://www.spinics.net/lists/linux-usb/msg57302.html
For PowerPC, there is dma_mask at struct pdev_archdata, but there is
no dma_mask at struct pdev_archdata for ARM. The pdev_archdata is
related to specific platform, it should NOT be accessed by
cross platform drivers, like USB.
The code for pdev_archdata should be useless, as for PowerPC,
it has already gotten the value for pdev->dev.dma_mask at function
arch_setup_pdev_archdata of arch/powerpc/kernel/setup-common.c.
The reason of above dump message is calling dma_poll_alloc with can-schedule
mem_flags at atomic context.
To fix this problem, below changes are made:
- fsl_req_to_dtd doesn't need to be protected by spin_lock_irqsave,
as struct usb_request can be access at process context. Move lock
to beginning of hardware visit (fsl_queue_td).
- Change the memory flag which using to allocate dTD descriptor buffer,
the memory flag can be from gadget layer.
It is tested at i.mx51 bbg board with g_mass_storage, g_ether, g_serial.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Acked-by: Li Yang <leoli@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We must not allow the input buffer length to change while we're
shuffling the buffer contents. We also mustn't clear the WDM_READ
flag after more data might have arrived. Therefore move both of these
into the spinlocked region at the bottom of wdm_read().
When reading desc->length without holding the iuspin lock, use
ACCESS_ONCE() to ensure the compiler doesn't re-read it with
inconsistent results.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Tested-by: Bjørn Mork <bjorn@mork.no> Cc: Oliver Neukum <oliver@neukum.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The unicode font map for the virtual console is a 32x32x64 table which
allocates rows dynamically as entries are added. The unicode value
increases sequentially and should count all entries even in empty
rows. The defect is when copying the unicode font map in con_set_unimap(),
the unicode value is not incremented properly. The wrong unicode value
is entered in the new font map.
Signed-off-by: Liz Clark <liz.clark@hp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is supposed to be doing a shift before the comparison instead of
just doing a bitwise AND directly. The current code means the start()
just returns without doing anything.
This patch fixies follwing two memory leak patterns that reported by kmemleak.
sysfs_sd_setsecdata() is called during sys_lsetxattr() operation.
It checks sd->s_iattr is NULL or not. Then if it is NULL, it calls
sysfs_init_inode_attrs() to allocate memory.
That code is this.
iattrs = sd->s_iattr;
if (!iattrs)
iattrs = sysfs_init_inode_attrs(sd);
The iattrs recieves sysfs_init_inode_attrs()'s result, but sd->s_iattr
doesn't know the address. so it needs to set correct address to
sd->s_iattr to free memory in other function.
Some of the newer futex PI opcodes do not check the cmpxchg enabled
variable and call unconditionally into the handling functions. Cover
all PI opcodes in a separate check.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HID devices should specify this in their interface descriptors, not in the
device descriptor. This fixes a "missing hardware id" bug under Windows 7 with
a VIA VL800 (3.0) controller.
A read from GadgetFS endpoint 0 during the data stage of a control
request would always return 0 on success (as returned by
wait_event_interruptible) despite having written data into the user
buffer.
This patch makes it correctly set the return value to the number of
bytes read.
Signed-off-by: Thomas Faber <thfabba@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb INDEX register is getting modified/corrupted during temporary
un-locking in a SMP system. Set this register with proper value
after re-acquiring the lock
Scenario:
---------
CPU1 is handling a data transfer completion interrupt received for
the CLASS1 EP
CPU2 is handling a CLASS2 thread which is queuing data to musb for
transfer
Below is the error sequence:
CPU1 | CPU2
--------------------------------------------------------------------
Data transfer completion inter- |
rupt recieved. |
|
musb INDEX reg set to CLASS1 EP |
|
musb LOCK is acquired. |
|
| CLASS2 thread queues data.
|
| CLASS2 thread tries to acquire musb
| LOCK but lock is already taken by
| CLASS1, so CLASS2 thread is
| spinning.
|
From Interrupt Context musb |
giveback function is called |
|
The giveback function releases | CLASS2 thread now acquires LOCK
LOCK |
|
ClASS1 Request's completion cal-| ClASS2 schedules the data transfer and
lback is called | sets the MUSB INDEX to Class2 EP number
|
Interrupt handler for CLASS1 EP |
tries to acquire LOCK and is |
spinning |
|
Interrupt for Class1 EP acquires| Class2 completes the scheduling etc and
the MUSB LOCK | releases the musb LOCK
|
Interrupt for Class1 EP schedul-|
es the next data transfer |
but musb INDEX register is still|
set to CLASS2 EP |
Since the MUSB INDEX register is set to a different endpoint, we
read and modify the wrong registers. Hence data transfer will not
happen properly. This results in unpredictable behavior
So, the MUSB INDEX register is set to proper value again when
interrupt re-acquires the lock
Add PID 0x6015, corresponding to the new series of FT-X chips
(FT220XD, FT201X, FT220X, FT221X, FT230X, FT231X, FT240X). They all
appear as serial devices, and seem indistinguishable except for the
default product string stored in their EEPROM. The baudrate
generation matches FT232RL devices.
Tested with a FT201X and FT230X at various baudrates (100 - 3000000).
Sample dmesg:
ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
usb 2-1: new full-speed USB device number 6 using ohci_hcd
usb 2-1: New USB device found, idVendor=0403, idProduct=6015
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-1: Product: FT230X USB Half UART
usb 2-1: Manufacturer: FTDI
usb 2-1: SerialNumber: DC001WI6
ftdi_sio 2-1:1.0: FTDI USB Serial Device converter detected
drivers/usb/serial/ftdi_sio.c: ftdi_sio_port_probe
drivers/usb/serial/ftdi_sio.c: ftdi_determine_type: bcdDevice = 0x1000, bNumInterfaces = 1
usb 2-1: Detected FT-X
usb 2-1: Number of endpoints 2
usb 2-1: Endpoint 1 MaxPacketSize 64
usb 2-1: Endpoint 2 MaxPacketSize 64
usb 2-1: Setting MaxPacketSize 64
drivers/usb/serial/ftdi_sio.c: read_latency_timer
drivers/usb/serial/ftdi_sio.c: write_latency_timer: setting latency timer = 1
drivers/usb/serial/ftdi_sio.c: create_sysfs_attrs
drivers/usb/serial/ftdi_sio.c: sysfs attributes for FT-X
usb 2-1: FTDI USB Serial Device converter now attached to ttyUSB0
Signed-off-by: Jim Paris <jim@jtan.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BeagleBone changed to the default FTDI 0403:6010 id in rev A5 to make life
easier for Windows users, so we need a similar workaround as the Calao
board to support it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some misconfigured ftdi_sio devices, if the manufacturer string is
NULL, the kernel will oops when the device is plugged in. This patch
fixes the problem.
Reported-by: Wojciech M Zabolotny <W.Zabolotny@elka.pw.edu.pl> Tested-by: Wojciech M Zabolotny <W.Zabolotny@elka.pw.edu.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device presents a total of 5 interfaces with ff/ff/ff
class/subclass/protocol. The last one of these is verified
to be a QMI/wwan combined interface which should be handled
by the qmi_wwan driver, so we blacklist it here.
commit 0d905fd "USB: option: convert Huawei K3765, K4505, K4605
reservered interface to blacklist" accidentally ANDed two
blacklist tests by leaving out a return. This was not noticed
because the two consecutive bracketless if statements made it
syntactically correct.
The code for "powersurge" SMP would kick in and cause a crash
at boot due to the lack of a NULL test.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com> Reported-by: Adam Conrad <adconrad@ubuntu.com> Tested-by: Adam Conrad <adconrad@ubuntu.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On il3945_down procedure we free tx queue data and nullify il->txq
pointer. After that we drop mutex and then cancel delayed works. There
is possibility, that after drooping mutex and before the cancel, some
delayed work will start and crash while trying to send commands to
the device. For example, here is reported crash in
il3945_bg_reg_txpower_periodic():
https://bugzilla.kernel.org/show_bug.cgi?id=42766#c10
Patch fix problem by adding il->txq check on works that send commands,
hence utilize tx queue.
Reported-by: Clemens Eisserer <linuxhippy@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ip6_mc_find_dev_rcu() is called with rcu_read_lock(), so don't
need to dev_hold().
With dev_hold(), not corresponding dev_put(), will lead to leak.
[ bug introduced in 96b52e61be1 (ipv6: mcast: RCU conversions) ]
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea4fc0d619 (ipv4: Don't use rt->rt_{src,dst} in ip_queue_xmit())
added a serious regression on synflood handling.
Simon Kirby discovered a successful connection was delayed by 20 seconds
before being responsive.
In my tests, I discovered that xmit frames were lost, and needed ~4
retransmits and a socket dst rebuild before being really sent.
In case of syncookie initiated connection, we use a different path to
initialize the socket dst, and inet->cork.fl.u.ip4 is left cleared.
As ip_queue_xmit() now depends on inet flow being setup, fix this by
copying the temp flowi4 we use in cookie_v4_check().
Reported-by: Simon Kirby <sim@netnation.com> Bisected-by: Simon Kirby <sim@netnation.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unfortunately this is not how snprintf works. snprintf returns the
number of characters that would have been written if there was enough
space. In the above case, if the first snprintf returns a value larger
than size, we pass a negative size into the second snprintf and happily
scribble over the stack. If you have 3000 character c++ methods thats a
lot of stack to trample.
This patch fixes repsep_snprintf by clamping the value at size - 1 which
is the maximum snprintf can write before adding the NULL terminator.
I get the sinking feeling that there are a lot of other uses of snprintf
that have this same bug, we should audit them all.
Cc: David Ahern <dsahern@gmail.com> Cc: Eric B Munson <emunson@mgebm.net> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Yanmin Zhang <yanmin_zhang@linux.intel.com> Link: http://lkml.kernel.org/r/20120307114249.44275ca3@kryten Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the report from Slicky Devil, nilfs caused kernel oops at
nilfs_load_super_block function during mount after he shrank the
partition without resizing the filesystem:
When the system is under heavy load, there can be a significant delay
between the getscl() and time_after() calls inside sclhi(). That delay
may cause the time_after() check to trigger after SCL has gone high,
causing sclhi() to return -ETIMEDOUT.
To fix the problem, double check that SCL is still low after the
timeout has been reached, before deciding to return -ETIMEDOUT.
Signed-off-by: Ville Syrjala <syrjala@sci.fi> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NCT6775F and NCT6776F have their own set of registers for FAN_STOP_TIME. The
correct registers were used to read FAN_STOP_TIME, but writes used the wrong
registers. Fix it.
Newer version of binutils are more strict about specifying the
correct options to enable certain classes of instructions.
The sparc32 build is done for v7 in order to support sun4c systems
which lack hardware integer multiply and divide instructions.
So we have to pass -Av8 when building the assembler routines that
use these instructions and get patched into the kernel when we find
out that we have a v8 capable cpu.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When pre-allocating skbs for received packets, we set ip_summed =
CHECKSUM_UNNCESSARY. We used to change it back to CHECKSUM_NONE when
the received packet had an incorrect checksum or unhandled protocol.
Commit bc8acf2c8c3e43fcc192762a9f964b3e9a17748b ('drivers/net: avoid
some skb->ip_summed initializations') mistakenly replaced the latter
assignment with a DEBUG-only assertion that ip_summed ==
CHECKSUM_NONE. This assertion is always false, but it seems no-one
has exercised this code path in a DEBUG build.
Fix this by moving our assignment of CHECKSUM_UNNECESSARY into
efx_rx_packet_gro().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1519) fixes a bug in the block layer's disk-events
polling. The polling is done by a work routine queued on the
system_nrt_wq workqueue. Since that workqueue isn't freezable, the
polling continues even in the middle of a system sleep transition.
Obviously, polling a suspended drive for media changes and such isn't
a good thing to do; in the case of USB mass-storage devices it can
lead to real problems requiring device resets and even re-enumeration.
The patch fixes things by creating a new system-wide, non-reentrant,
freezable workqueue and using it for disk-events polling.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Tejun Heo <tj@kernel.org> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Then we unblock events, when they are suppose to be blocked. This can
trigger events related block/genhd.c warnings, but also can crash in
sd_check_events() or other places.
I'm able to reproduce crashes with the following scripts (with
connected usb dongle as sdb disk).
function stop_me()
{
for i in `jobs -p` ; do kill $i 2> /dev/null ; done
exit
}
trap stop_me SIGHUP SIGINT SIGTERM
for ((i = 0; i < 10; i++)) ; do
while true; do fdisk -l $DEV 2>&1 > /dev/null ; done &
done
while true ; do
echo 1 > $ENABLE
sleep 1
echo 0 > $ENABLE
done
</snip>
I use the script to verify patch fixing oops in sd_revalidate_disk
http://marc.info/?l=linux-scsi&m=132935572512352&w=2
Without Jun'ichi Nomura patch titled "Fix NULL pointer dereference in
sd_revalidate_disk" or this one, script easily crash kernel within
a few seconds. With both patches applied I do not observe crash.
Unfortunately after some time (dozen of minutes), script will hung in:
As drawback, I do not teardown on sysfs file create error, because I do
not know how to nullify disk->ev (since it can be used). However add_disk
error handling practically does not exist too, and things will work
without this sysfs file, except events will not be exported to user
space.
Since 2.6.39 (1196f8b), when a driver returns -ENOMEDIUM for open(),
__blkdev_get() calls rescan_partitions() to remove
in-kernel partition structures and raise KOBJ_CHANGE uevent.
However it ends up calling driver's revalidate_disk without open
and could cause oops.
In the case of SCSI:
process A process B
----------------------------------------------
sys_open
__blkdev_get
sd_open
returns -ENOMEDIUM
scsi_remove_device
<scsi_device torn down>
rescan_partitions
sd_revalidate_disk
<oops>
Oopses are reported here:
http://marc.info/?l=linux-scsi&m=132388619710052
This patch separates the partition invalidation from rescan_partitions()
and use it for -ENOMEDIUM case.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the Sitecom LN-031 USB adapter with a AX88178 chip.
Added USB id to find correct driver for AX88178 1000 Ethernet adapter.
Signed-off-by: Joerg Neikes <j.neikes@midlandgate.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver attempts to use two TX rings but lacks proper support :
1) IRQ handler only takes care of TX completion on first TX ring
2) the stop/start logic uses the legacy functions (for non multiqueue
drivers)
This means all packets witk skb mark set to 1 are sent through high
queue but are never cleaned and queue eventualy fills and block the
device, triggering the infamous "NETDEV WATCHDOG" message.
Lets use a single TX ring to fix the problem, this driver is not a real
multiqueue one yet.
Minimal fix for stable kernels.
Reported-by: Thomas Meyer <thomas@m3y3r.de> Tested-by: Thomas Meyer <thomas@m3y3r.de> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Jay Cliburn <jcliburn@gmail.com> Cc: Chris Snook <chris.snook@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When forwarding was set and a new net device is register,
we need add this device to the all-router mcast group.
Signed-off-by: Li Wei <lw@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes tcp_shift_skb_data() so that it does not shift
SACKed data below snd_una.
This fixes an issue whose symptoms exactly match reports showing
tp->sacked_out going negative since 3.3.0-rc4 (see "WARNING: at
net/ipv4/tcp_input.c:3418" thread on netdev).
Since 2008 (832d11c5cd076abc0aa1eaf7be96c81d1a59ce41)
tcp_shift_skb_data() had been shifting SACKed ranges that were below
snd_una. It checked that the *end* of the skb it was about to shift
from was above snd_una, but did not check that the end of the actual
shifted range was above snd_una; this commit adds that check.
Shifting SACKed ranges below snd_una is problematic because for such
ranges tcp_sacktag_one() short-circuits: it does not declare anything
as SACKed and does not increase sacked_out.
Before the fixes in commits cc9a672ee522d4805495b98680f4a3db5d0a0af9
and daef52bab1fd26e24e8e9578f8fb33ba1d0cb412, shifting SACKed ranges
below snd_una happened to work because tcp_shifted_skb() was always
(incorrectly) passing in to tcp_sacktag_one() an skb whose end_seq
tcp_shift_skb_data() had already guaranteed was beyond snd_una. Hence
tcp_sacktag_one() never short-circuited and always increased
tp->sacked_out in this case.
After those two fixes, my testing has verified that shifting SACKed
ranges below snd_una could cause tp->sacked_out to go negative with
the following sequence of events:
(1) tcp_shift_skb_data() sees an skb whose end_seq is beyond snd_una,
then shifts a prefix of that skb that is below snd_una
(2) tcp_shifted_skb() increments the packet count of the
already-SACKed prev sk_buff
(3) tcp_sacktag_one() sees the end of the new SACKed range is below
snd_una, so it short-circuits and doesn't increase tp->sacked_out
(5) tcp_clean_rtx_queue() sees the SACKed skb has been ACKed,
decrements tp->sacked_out by this "inflated" pcount that was
missing a matching increase in tp->sacked_out, and hence
tp->sacked_out underflows to a u32 like 0xFFFFFFFF, which casted
to s32 is negative.
(6) this leads to the warnings seen in the recent "WARNING: at
net/ipv4/tcp_input.c:3418" thread on the netdev list; e.g.:
tcp_input.c:3418 WARN_ON((int)tp->sacked_out < 0);
More generally, I think this bug can be tickled in some cases where
two or more ACKs from the receiver are lost and then a DSACK arrives
that is immediately above an existing SACKed skb in the write queue.
This fix changes tcp_shift_skb_data() to abort this sequence at step
(1) in the scenario above by noticing that the bytes are below snd_una
and not shifting them.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
otherwise source IPv6 address of ICMPV6_MGM_QUERY packet
might be random junk if IPv6 is disabled on interface or
link-local address is not yet ready (DAD).
Signed-off-by: Ulrich Weber <ulrich.weber@sophos.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In tcp_mark_head_lost() we should not attempt to fragment a SACKed skb
to mark the first portion as lost. This is for two primary reasons:
(1) tcp_shifted_skb() coalesces adjacent regions of SACKed skbs. When
doing this, it preserves the sum of their packet counts in order to
reflect the real-world dynamics on the wire. But given that skbs can
have remainders that do not align to MSS boundaries, this packet count
preservation means that for SACKed skbs there is not necessarily a
direct linear relationship between tcp_skb_pcount(skb) and
skb->len. Thus tcp_mark_head_lost()'s previous attempts to fragment
off and mark as lost a prefix of length (packets - oldcnt)*mss from
SACKed skbs were leading to occasional failures of the WARN_ON(len >
skb->len) in tcp_fragment() (which used to be a BUG_ON(); see the
recent "crash in tcp_fragment" thread on netdev).
(2) there is no real point in fragmenting off part of a SACKed skb and
calling tcp_skb_mark_lost() on it, since tcp_skb_mark_lost() is a NOP
for SACKed skbs.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Acked-by: Yuchung Cheng <ycheng@google.com> Acked-by: Nandita Dukkipati <nanditad@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When tcp_shifted_skb() shifts bytes from the skb that is currently
pointed to by 'highest_sack' then the increment of
TCP_SKB_CB(skb)->seq implicitly advances tcp_highest_sack_seq(). This
implicit advancement, combined with the recent fix to pass the correct
SACKed range into tcp_sacktag_one(), caused tcp_sacktag_one() to think
that the newly SACKed range was before the tcp_highest_sack_seq(),
leading to a call to tcp_update_reordering() with a degree of
reordering matching the size of the newly SACKed range (typically just
1 packet, which is a NOP, but potentially larger).
This commit fixes this by simply calling tcp_sacktag_one() before the
TCP_SKB_CB(skb)->seq advancement that can advance our notion of the
highest SACKed sequence.
Correspondingly, we can simplify the code a little now that
tcp_shifted_skb() should update the lost_cnt_hint in all cases where
skb == tp->lost_skb_hint.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a (mostly cosmetic) bug introduced by the patch
'ppp: Use SKB queue abstraction interfaces in fragment processing'
found here: http://www.spinics.net/lists/netdev/msg153312.html
The above patch rewrote and moved the code responsible for cleaning
up discarded fragments but the new code does not catch every case
where this is necessary. This results in some discarded fragments
remaining in the queue, and triggering a 'bad seq' error on the
subsequent call to ppp_mp_reconstruct. Fragments are discarded
whenever other fragments of the same frame have been lost.
This can generate a lot of unwanted and misleading log messages.
This patch also adds additional detail to the debug logging to
make it clearer which fragments were lost and which other fragments
were discarded as a result of losses. (Run pppd with 'kdebug 1'
option to enable debug logging.)
Signed-off-by: Ben McKeegan <ben@netservers.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Niccolò Belli <darkbasic@linuxsystems.it> Tested-by: Niccolò Belli <darkbasic@linuxsystems.it> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. While function neigh_periodic_work scans the neighbor hash table
pointed by field tbl->nht, it unlocks and locks tbl->lock between
buckets in order to call cond_resched.
2. Assume that function neigh_periodic_work calls cond_resched, that is,
the lock tbl->lock is available, and function neigh_hash_grow runs.
3. Once function neigh_hash_grow finishes, and RCU calls
neigh_hash_free_rcu, the original struct neigh_hash_table that function
neigh_periodic_work was using doesn't exist anymore.
4. Once back at neigh_periodic_work, whenever the old struct
neigh_hash_table is accessed, things can go badly.
Signed-off-by: Michel Machado <michel@digirati.com.br> CC: "David S. Miller" <davem@davemloft.net> CC: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have several reports which says acer-wmi is loaded on ideapads
and register rfkill for wifi which can not be unblocked.
Since ideapad-laptop also register rfkill for wifi and it works
reliably, it will be fine acer-wmi is not going to register rfkill
for wifi once VPC2004 is found.
Also put IBM0068/LEN0068 in the list. Though thinkpad_acpi has no
wifi rfkill capability, there are reports which says acer-wmi also
block wireless on Thinkpad E520/E420.
Signed-off-by: Ike Panhc <ike.pan@canonical.com> Signed-off-by: Matthew Garrett <mjg@redhat.com> Cc: Jonathan Nieder <jrnieder@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There will be better to check the wireless capability flag
(ACER_CAP_WIRELESS) before register wireless rfkill because maybe
the machine doesn't have wifi module or the module removed by user.
Tested on Acer Travelmate 8572
Tested on Acer Aspire 4739Z
Tested-by: AceLan Kao <acelan.kao@canonical.com> Cc: Carlos Corbacho <carlos@strangeworlds.co.uk> Cc: Matthew Garrett <mjg@redhat.com> Cc: Dmitry Torokhov <dtor@mail.ru> Cc: Corentin Chary <corentincj@iksaif.net> Cc: Thomas Renninger <trenn@suse.de> Signed-off-by: Lee, Chun-Yi <jlee@suse.com> Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AMW0 function in acer-wmi works on Lenovo ideapad S205 for control
the wifi hardware state. We also found there have a 0x78 EC register
exposes the state of wifi hardware switch on the machine.
So, add this patch to support Lenovo ideapad S205 wifi hardware switch
in acer-wmi driver.
complete_walk() returns either ECHILD or ESTALE. do_last() turns this into
ECHILD unconditionally. If not in RCU mode, this error will reach userspace
which is complete nonsense.
Is possible that we stop queue and then do not wake up it again,
especially when packets are transmitted fast. That can be easily
reproduced with modified tx queue entry_num to some small value e.g. 16.
If mac80211 already hold local->queue_stop_reason_lock, then we can wait
on that lock in both rt2x00queue_pause_queue() and
rt2x00queue_unpause_queue(). After drooping ->queue_stop_reason_lock
is possible that __ieee80211_wake_queue() will be performed before
__ieee80211_stop_queue(), hence we stop queue and newer wake up it
again.
Another race condition is possible when between rt2x00queue_threshold()
check and rt2x00queue_pause_queue() we will process all pending tx
buffers on different cpu. This might happen if for example interrupt
will be triggered on cpu performing rt2x00mac_tx().
To prevent race conditions serialize pause/unpause by queue->tx_lock.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disabling all runtime PM during system shutdown turns out not to be a
good idea, because some devices may need to be woken up from a
low-power state at that time.
The whole point of disabling runtime PM for system shutdown was to
prevent untimely runtime-suspend method calls. This patch (as1504)
accomplishes the same result by incrementing the usage count for each
device and waiting for ongoing runtime-PM callbacks to finish. This
is what we already do during system suspend and hibernation, which
makes sense since the shutdown method is pretty much a legacy analog
of the pm->poweroff method.
This fixes a recent regression on some OMAP systems introduced by
commit af8db1508f2c9f3b6e633e2d2d906c6557c617f9 (PM / driver core:
disable device's runtime PM during shutdown).
Reported-and-tested-by: NeilBrown <neilb@suse.de> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Kostyantyn Shlyakhovoy <x0155534@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some older Panasonic made camcorders (Panasonic AG-EZ30 and NV-DX110,
Grundig Scenos DLC 2000) reject requests with ack_busy_X if a request is
sent immediately after they sent a response to a prior transaction.
This causes firewire-core to fail probing of the camcorder with "giving
up on config rom for node id ...". Consequently, programs like kino or
dvgrab are unaware of the presence of a camcorder.
Such transaction failures happen also with the ieee1394 driver stack
(of the 2.4...2.6 kernel series until 2.6.36 inclusive) but with a lower
likelihood, such that kino or dvgrab are generally able to use these
camcorders via the older driver stack. The cause for firewire-ohci's or
firewire-core's worse behavior is not yet known. Gap count optimization
in firewire-core is not the cause. Perhaps the slightly higher latency
of transaction completion in the older stack plays a role. (ieee1394:
AR-resp DMA context tasklet -> packet completion ktread -> user process;
firewire-core: tasklet -> user process.)
This change introduces retries and delays after ack_busy_X into
firewire-core's Config ROM reader, such that at least firewire-core's
probing and /dev/fw* creation are successful. This still leaves the
problem that userland processes are facing transaction failures.
gscanbus's built-in retry routines deal with them successfully, but
neither kino's nor dvgrab's do ever succeed.
But at least DV capture with "dvgrab -noavc -card 0" works now. Live
video preview in kino works too, but not actual capture.
One way to prevent Configuration ROM reading failures in application
programs is to modify libraw1394 to synthesize read responses by means
of firewire-core's Configuration ROM cache. This would only leave
CMP and FCP transaction failures as a potential problem source for
applications.
Reported-and-tested-by: Thomas Seilund <tps@netmaster.dk> Reported-and-tested-by: René Fritz <rene@colorcube.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clemens points out that we need to use compat_ptr() in order to safely
cast from u64 to addresses of a 32-bit usermode client.
Before, our conversion went wrong
- in practice if the client cast from pointer to integer such that
sign-extension happened, (libraw1394 and libdc1394 at least were not
doing that, IOW were not affected)
or
- in theory on s390 (which doesn't have FireWire though) and on the
tile architecture, regardless of what the client does.
The bug would usually be observed as the initial get_info ioctl failing
with "Bad address" (EFAULT).
Reported-by: Carl Karsten <carl@personnelware.com> Reported-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now we won't touch ASPM state if ASPM is disabled, except in the case
where we find a device that appears to be too old to reliably support ASPM.
Right now we'll clear it in that case, which is almost certainly the wrong
thing to do. The easiest way around this is just to disable the blacklisting
when ASPM is disabled.
Commit f0fbf0abc093 ("x86: integrate delay functions") converted
delay_tsc() into a random delay generator for 64 bit. The reason is
that it merged the mostly identical versions of delay_32.c and
delay_64.c. Though the subtle difference of the result was:
static void delay_tsc(unsigned long loops)
{
- unsigned bclock, now;
+ unsigned long bclock, now;
Now the function uses rdtscl() which returns the lower 32bit of the
TSC. On 32bit that's not problematic as unsigned long is 32bit. On 64
bit this fails when the lower 32bit are close to wrap around when
bclock is read, because the following check
if ((now - bclock) >= loops)
break;
evaluated to true on 64bit for e.g. bclock = 0xffffffff and now = 0
because the unsigned long (now - bclock) of these values results in
0xffffffff00000001 which is definitely larger than the loops
value. That explains Tvortkos observation:
"Because I am seeing udelay(500) (_occasionally_) being short, and
that by delaying for some duration between 0us (yep) and 491us."
Make those variables explicitely u32 again, so this works for both 32
and 64 bit.
Current code has put_ioctx() called asynchronously from aio_fput_routine();
that's done *after* we have killed the request that used to pin ioctx,
so there's nothing to stop io_destroy() waiting in wait_for_all_aios()
from progressing. As the result, we can end up with async call of
put_ioctx() being the last one and possibly happening during exit_mmap()
or elf_core_dump(), neither of which expects stray munmap() being done
to them...
We do need to prevent _freeing_ ioctx until aio_fput_routine() is done
with that, but that's all we care about - neither io_destroy() nor
exit_aio() will progress past wait_for_all_aios() until aio_fput_routine()
does really_put_req(), so the ioctx teardown won't be done until then
and we don't care about the contents of ioctx past that point.
Since actual freeing of these suckers is RCU-delayed, we don't need to
bump ioctx refcount when request goes into list for async removal.
All we need is rcu_read_lock held just over the ->ctx_lock-protected
area in aio_fput_routine().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Acked-by: Benjamin LaHaise <bcrl@kvack.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Have ioctx_alloc() return an extra reference, so that caller would drop it
on success and not bother with re-grabbing it on failure exit. The current
code is obviously broken - io_destroy() from another thread that managed
to guess the address io_setup() would've returned would free ioctx right
under us; gets especially interesting if aio_context_t * we pass to
io_setup() points to PROT_READ mapping, so put_user() fails and we end
up doing io_destroy() on kioctx another thread has just got freed...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Benjamin LaHaise <bcrl@kvack.org> Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Silence following warnings:
WARNING: drivers/mfd/cs5535-mfd.o(.data+0x20): Section mismatch in
reference from the variable cs5535_mfd_drv to the function
.devinit.text:cs5535_mfd_probe()
The variable cs5535_mfd_drv references
the function __devinit cs5535_mfd_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: drivers/mfd/cs5535-mfd.o(.data+0x28): Section mismatch in
reference from the variable cs5535_mfd_drv to the function
.devexit.text:cs5535_mfd_remove()
The variable cs5535_mfd_drv references
the function __devexit cs5535_mfd_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Rename the variable from *_drv to *_driver so
modpost ignore the OK references to __devinit/__devexit
functions.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Acked-by: Andres Salomon <dilinger@queued.net> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both md and dm have support for flush, but the dm-raid target
forgot to set the flag to indicate that flushes should be
passed on. (Important for data integrity e.g. with writeback cache
enabled.)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Acked-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|kernel BUG at kernel/rtmutex.c:724!
|[<c029599c>] (rt_spin_lock_slowlock+0x108/0x2bc) from [<c01c2330>] (defer_bh+0x1c/0xb4)
|[<c01c2330>] (defer_bh+0x1c/0xb4) from [<c01c3afc>] (rx_complete+0x14c/0x194)
|[<c01c3afc>] (rx_complete+0x14c/0x194) from [<c01cac88>] (usb_hcd_giveback_urb+0xa0/0xf0)
|[<c01cac88>] (usb_hcd_giveback_urb+0xa0/0xf0) from [<c01e1ff4>] (musb_giveback+0x34/0x40)
|[<c01e1ff4>] (musb_giveback+0x34/0x40) from [<c01e2b1c>] (musb_advance_schedule+0xb4/0x1c0)
|[<c01e2b1c>] (musb_advance_schedule+0xb4/0x1c0) from [<c01e2ca8>] (musb_cleanup_urb.isra.9+0x80/0x8c)
|[<c01e2ca8>] (musb_cleanup_urb.isra.9+0x80/0x8c) from [<c01e2ed0>] (musb_urb_dequeue+0xec/0x108)
|[<c01e2ed0>] (musb_urb_dequeue+0xec/0x108) from [<c01cbb90>] (unlink1+0xbc/0xcc)
|[<c01cbb90>] (unlink1+0xbc/0xcc) from [<c01cc2ec>] (usb_hcd_unlink_urb+0x54/0xa8)
|[<c01cc2ec>] (usb_hcd_unlink_urb+0x54/0xa8) from [<c01c2a84>] (unlink_urbs.isra.17+0x2c/0x58)
|[<c01c2a84>] (unlink_urbs.isra.17+0x2c/0x58) from [<c01c2b44>] (usbnet_terminate_urbs+0x94/0x10c)
|[<c01c2b44>] (usbnet_terminate_urbs+0x94/0x10c) from [<c01c2d68>] (usbnet_stop+0x100/0x15c)
|[<c01c2d68>] (usbnet_stop+0x100/0x15c) from [<c020f718>] (__dev_close_many+0x94/0xc8)
defer_bh() takes the lock which is hold during unlink_urbs(). The safe
walk suggest that the skb will be removed from the list and this is done
by defer_bh() so it seems to be okay to drop the lock here.
Reported-by: AnÃbal Almeida Pinto <anibal.pinto@efacec.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Access Point mode, when transmitting a packet, if the destination
station is in powersave mode, we abort transmitting the packet to the
device queue, but we do not reclaim the allocated memory. Given enough
packets, we can go in a state where there is no packet on the device
queue, but we think the device has no memory left, so no packet gets
transmitted, connections breaks and the AP stops working.
This undo the allocation done in the TX path when the station is in
power-save mode.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log