Tom Rini [Wed, 5 Feb 2014 15:24:22 +0000 (10:24 -0500)]
cmd_mmc.c: Add bootbus mmc sub-command
Add a bootbus sub-command to the mmc command to allow for setting
the boot_bus_width, reset_boot_bus_width and boot_mode fields of
BOOT_BUS_WIDTH (EXT_CSD[177]).
Tom Rini [Wed, 5 Feb 2014 15:24:21 +0000 (10:24 -0500)]
cmd_mmc.c: Add 'partconf' command to mmc
Add a partconf sub-command to the mmc command to allow for setting
the boot_ack, boot_partition and partition_access fields of
PARTITION_CONFIG (formerly BOOT_CONFIG, EXT_CSD[179]). Part of this
requires changing the check for 'part' from an strncmp to a strcmp, like
the rest of the sub-commands.
Cc: Andy Fleming <afleming@gmail.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Tom Rini [Wed, 5 Feb 2014 15:24:18 +0000 (10:24 -0500)]
SPL: Add CONFIG_SUPPORT_EMMC_BOOT support to CONFIG_SPL_FRAMEWORK
We use the switch CONFIG_SUPPORT_EMMC_BOOT today to enable some
additional features of the eMMC boot partitions. Add support for being
told that we have booted from one of these partitions to the spl
framework and implement this on TI OMAP/related.
As per the below commit
"mmc: sdhci: add the quirk for broken r1b response"
(sha1: 3a6383207be3f71b39004e64464a6e99290b16fa)
need to add quirk SDHCI_QUIRK_BROKEN_R1B, when the
response type is R1b.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch corrects the divider value written to CLKDIV register.
Since SDCLKIN is divided inside controller by the DIVRATIO value set
in the CLKSEL register, we need to use the same output clock value to
calculate the CLKDIV value.
as per user manual: cclk_in = SDCLKIN / (DIVRATIO + 1)
Input parameter to mmc_clk is changed to dwmci_host, since
we need the same to read DWMCI_CLKSEL register.
This improves the read timing values for channel 0 on SMDK5250
from 0.288sec to 0.144sec
Stephen Warren [Thu, 30 Jan 2014 23:11:12 +0000 (16:11 -0700)]
mmc: set rca to 1 for MMC cards
U-Boot currently sets MMC cards' RCA register to 0. This value is
reserved according to the specification. Use a value of 1 instead, just
like the Linux kernel.
fpga: zynq: Correct fpga load when buf is not aligned
When ARCH_DMA_MINALIGN is greater than header size of the bit file, and buf is
not aligned, new_buf address became greater then buf_start address and the
load_word loop corrupts bit file data.
A work around is to decrease new_buf of ARCH_DMA_MINALIGN, it might corrupt data
before buf but permits to load correctly.
Signed-off-by: Stany MARCEL <smarcel@novasys-ingenierie.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Marek Vasut [Thu, 6 Feb 2014 01:43:45 +0000 (02:43 +0100)]
usb: mv_udc: Rename to ci_udc
The mv_udc is not marvell-specific anymore. The mv_udc is used to drive
generic ChipIdea CI13xxx series OTG cores, so rename the driver to ci_udc
instead.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Stefano Babic <sbabic@denx.de>
Lukasz Majewski [Wed, 5 Feb 2014 09:10:44 +0000 (10:10 +0100)]
usb:udc:samsung: Zero copy approach for data passed to Samsung's UDC driver
The Samsung's UDC driver is not anymore copying data from USB requests to
aligned internal buffers. Now it works directly in data allocated in the
upper layers like UMS, DFU, THOR.
This change is possible since those gadgets now must take care to allocate
buffers aligned to cache line (CONFIG_SYS_CACHELINE_SIZE).
This can be achieved by using DEFINE_CACHE_ALIGN_BUFFER() or
ALLOC_CACHE_ALIGN_BUFFER() macros. Those take care to allocate buffer
aligned to cache line in both starting address and its size.
Sometimes it is enough to just use memalign() with size being a
multiplication of cache line size.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurement:
Transmission speed: 27.04 MiB/s
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
Lukasz Majewski [Wed, 5 Feb 2014 09:10:43 +0000 (10:10 +0100)]
usb:udc:samsung: Allow burst transfers for non EP0 endpints
This patch removed obscure restriction on the HW setting of DMA transfers.
Before this change each transaction sent up to 512 bytes (with packet count
equal to 1) for non EP0 transfer.
Now it is possible to setup DMA transaction up to DMA_BUFFER_SIZE.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurement:
Transmission speed: 20.74 MiB/s
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
Lukasz Majewski [Wed, 5 Feb 2014 09:10:42 +0000 (10:10 +0100)]
usb:udc:samsung: Remove redundant cache operation from Samsung UDC driver
A set of cache operations (both invalidation and flush) were redundant
in the S3C HS OTG Samsung driver:
1. s3c_udc_ep0_zlp - to transmit EP0's ZLP packets one don't need to flush
the cache (since it is the zero length transmission)
2. s3c_udc_pre_setup and s3c_ep0_complete_out - cache invalidation is not
needed when the buffer for OUT EP0 transmission is setup, since no data
has yet arrived.
Cache cleanups presented above don't contribute much to transmission speed
up, hence shall be regarded as cosmetic changes.
3. setdma_rx - here the s3c UDC driver's internal buffers were invalidated.
This call is not needed anymore since we reuse the buffers passed from
gadgets. This is a key contribution to transmission speed improvement.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurements:
Base values (without improvement):
Transmission speed: 9.51 MiB/s
After the change:
Transmission speed: 10.15 MiB/s
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
Dennis Gilmore [Tue, 4 Feb 2014 11:25:47 +0000 (05:25 -0600)]
config: add config_distro_defaults.h
describe a set of default features that distros can rely on being available.
having this common definition means that distros can easily support systems
implementing them.
Stephen Warren [Tue, 28 Jan 2014 21:50:10 +0000 (14:50 -0700)]
pxe: implement fdtdir extlinux.conf tag
People who write (or scripts that auto-generate) extlinux.conf don't
want to know about HW-specific information such as FDT filenames. Create
a new extlinux.conf tag "fdtdir" that specifies only the directory where
FDT files are located, and defer all knowledge of the filename to U-Boot.
The algorithm implemented is:
==========
if $fdt_addr_r is set:
if "fdt" tag was specified in extlinux.conf:
load the FDT from the filename in the tag
else if "fdtdir" tag was specified in extlinux.conf:
if "fdtfile" is set in the environment:
load the FDT from filename in "$fdtfile"
else:
load the FDT from some automatically generated filename
if no FDT file was loaded, and $fdtaddr is set:
# This indicates an FDT packaged with firmware
use the FDT at $fdtaddr
==========
A small part of an example /boot/extlinux.conf might be:
==========
LABEL primary
LINUX zImage
FDTDIR ./
LABEL failsafe
LINUX bkp/zImage
FDTDIR bkp/
==========
... with /boot/tegra20-seaboard.dtb or /boot/bkp/tegra20-seaboard.dtb
being loaded by the sysboot/pxe code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
kmp204x: initial support for PCIe FPGA configuration
The PEXHC PCIe configuration mechanism ensures that the FPGA get
configured at power-up. Since all the PCIe devices should be configured
when the kernel start, u-boot has to take care that the FPGA gets
configured also in other reset scenarios, mostly because of possible
configuration change.
The used mechanism is taken from the km_kirkwood design and adapted to
the kmp204x case (slightly different HW and PCIe configuration).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
This define can be used if the ubi boot partition (defined for all
Keymile boards with KM_UBI_PARTITION_NAME_BOOT #define to ubi0) needs
some additionnal boot options.
This is the case for the kmp204x boards since u-boot does not support
NAND Flash subpage accesses on this platform, an additionnal argument
that defines the VID offstet must be given to the kernel.
The UBI cmd line option now looks like this "ubi.mtd=ubi0,2048" on this
platform.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
The kmcoge4 board is the product board derived from the kmlion1
prototype. The main difference between the 2 boards is that the kmcoge4
does not configure the Local Bus controller for LCS2.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: Minor change to boards.cfg to keep targets in order] Signed-off-by: York Sun <yorksun@freescale.com>
According to the errata, some bits of an undocumented register in the
DCSR must be set for every core in order to avoid a possible data or
instruction corruption.
This is required for the 2.0 revision of the P2041 that should be used
as soon as available in our design.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
Rainer Boschung [Mon, 3 Feb 2014 07:45:40 +0000 (08:45 +0100)]
kmp204x: I2C deblocking support
This patch adds support for using some GPIOs that are connected to the
I2C bus to force the bus lines state and perform some bus deblocking
sequences.
The KM common deblocking algorithm from board/keymile/common/common.c is
used. The GPIO lines used for deblocking the I2C bus are some external
GPIOs provided by the QRIO CPLD:
- SCL = GPIOA_20
- SDA = GPIOA_21
The QRIO GPIOs act in an open-drain-like manner, for 0 the line is
driven low and for 1 the GPIO is set as input and the line gets
pulled-up.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
The QRIO GPIO functions can be of general interest. They are thus added
to a qrio.c and their prototype are available from kmp204x.h. The QRIO
prst function are also included in this file, as well as the functions
required for the I2C deblocking support (open-drain).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: Remove extra blank line in board/keymile/kmp204x/qrio.c] Signed-off-by: York Sun <yorksun@freescale.com>
Rainer Boschung [Mon, 27 Jan 2014 10:49:04 +0000 (11:49 +0100)]
kmp204x: support for QRIO1 bootcounter
Make use of the QRIO1 32bit register at 0x20 as bootcounter register
Check for BOOTCOUNT_MAGIC pattern when before bootcounter value is read
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: Minor change to commit message] Signed-off-by: York Sun <yorksun@freescale.com>
Priyanka Jain [Thu, 30 Jan 2014 06:00:04 +0000 (11:30 +0530)]
powerpc/t104xrdb: Add basic ethernet support
This covers only non-L2 switch ethernet interfaces i.e.
RGMII and SGMII interface for both T1040RDB and T1042RDB_PI
T1040RDB is configured as serdes protocol 0x66 which can
support following interfaces
2 RGMIIS on DTSEC4, DTSEC5
1 SGMII on DTSEC3
T1042RDB_PI is configured as serdes protocol 0x06 which can
support following interfaces
2 RGMIIS on DTSEC4, DTSEC5
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: Minor change in commit message] Signed-off-by: York Sun <yorksun@freescale.com>
Priyanka Jain [Mon, 27 Jan 2014 08:37:11 +0000 (14:07 +0530)]
powerpc/t104xrdb: Update T1040RDB.h in config folder
Add usb2 node entry in "hwconfig string"
Remove controller interleaving from hwconfig string as T1040
has only one DDR conroller
SPI related macros which were earlier under #ifdef CONFIG_SPIFLASH
are move outside so that they are defined for all cases as these
macros are also used by other u-boot code
Add CONFIG_SYS_CSPR2_EXT to make CPLD accessible
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: Minor change to commit message] Signed-off-by: York Sun <yorksun@freescale.com>
Enable entherent for T1040QDS. It enables FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5
Define MDIO related configs
Added eth.c file
Update t1040.c to support RGMII and SGMII
Update t1040qds.c to support ethernet
Define the PHY address
Ezequiel Garcia [Tue, 28 Jan 2014 10:19:06 +0000 (07:19 -0300)]
board: nios2: Check if flash is configured before calling early_flash_cmd_reset()
If CONFIG_CFI_FLASH_MTD is not defined, then we shouldn't perform the
flash early reset.
This commit fixes the following build error:
nios2-generic.c: In function `__early_flash_cmd_reset':
nios2-generic.c:23: error: `AMD_CMD_RESET' undeclared (first use in this function)
nios2-generic.c:23: error: (Each undeclared identifier is reported only once
nios2-generic.c:23: error: for each function it appears in.)
nios2-generic.c:24: error: `FLASH_CMD_RESET' undeclared (first use in this function)
Alexey Brodkin [Mon, 20 Jan 2014 10:30:39 +0000 (14:30 +0400)]
board_r - fixup functions table after relocation
This is only required for "PIC" relocation and doesn't apply to modern
"PIE" relocation which does data relocation as well as code.
"init_sequence_r" is just an array that consists of compile-time
adresses of init functions. Since this is basically an array of integers
(pointers to "void" to be more precise) it won't be modified during
relocation - it will be just copied to new location as it is.
As a consequence on execution after relocation "initcall_run_list" will
be jumping to pre-relocation addresses. As long as we don't overwrite
pre-relocation memory area init calls are executed correctly. But still
it is dangerous because after relocation we don't expect initially used
memory to stay untouched.
Cc: Tom Rini <trini@ti.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Doug Anderson <dianders@chromium.org> Cc: Thomas Langer <thomas.langer@lantiq.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Dan Murphy [Thu, 16 Jan 2014 17:23:30 +0000 (11:23 -0600)]
spl: common: Support for USB MSD FAT image loading
Add SPL support to be able to detect a USB Mass Storage device
connected to a USB host. Once a USB Mass storage device is detected
the SPL will load the u-boot.img from a FAT partition to target address.
Masahiro Yamada [Wed, 15 Jan 2014 02:00:45 +0000 (11:00 +0900)]
ARM: merge commonly-defined PLATFORM_RELFLAGS
Before this commit, all arch/arm/cpu/${CPU}/config.mk except ARMv8
had the same option:
$(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,))
This commit moves it into arch/arm/config.mk.
If the compiler does not support the option,
it is ignored by $(call cc-option,...).
So this commit gives no harm to ARMv8.
We do not have to define CONFIG_4xx in board config headers
because it is defined in arch/powerpc/cpu/ppc4xx/config.mk.
include/configs/JSE.h defines "CONFIG_4x", not "CONFIG_4xx".
I believe it is a typo because "CONFIG_4x" is not used at all
in other files.
So, I also deleted "CONFIG_4x" in include/configs/JSE.h.
Masahiro Yamada [Tue, 14 Jan 2014 01:55:02 +0000 (10:55 +0900)]
board: tec-ng: Do not make directories in a board Makefile
Commit e5c5301f refactored the build system not to make
directories in board makefiles.
But commit 8f380381 create directories again in
board/avionic-design/tec-ng/Makefile.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Alban Bedel <alban.bedel@avionic-design.de>
Darwin Rambo [Thu, 19 Dec 2013 23:14:19 +0000 (15:14 -0800)]
lib: fix return codes when CONFIG_SYS_VSNPRINTF is enabled
When CONFIG_SYS_VSNPRINTF is enabled, it protects print operations
such as sprintf, snprintf, vsnprintf, etc., from buffer overflows.
But vsnprintf_internal includes the terminating NULL character in
the calculation of number of characters written. This affects sprintf
and snprintf return values. Fix this issue by setting pointer 'str'
back to the location of the '\0'.
Signed-off-by: Darwin Rambo <drambo@broadcom.com> Reviewed-by: Steve Rae <srae@broadcom.com>
Darwin Rambo [Thu, 19 Dec 2013 23:06:12 +0000 (15:06 -0800)]
lib: time: add weak timer_init() function
If timer_init() is made a weak stub function, then it allows us to
remove several empty timer_init functions for those boards that
already have a timer initialized when u-boot starts. Architectures
that use the timer framework may also remove the need for timer.c.
Signed-off-by: Darwin Rambo <drambo@broadcom.com> Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Haijun.Zhang [Fri, 10 Jan 2014 05:52:19 +0000 (13:52 +0800)]
eSDHC: Calculate envaddr accroding to the address format
On BSC9131, BSC9132, P1010 : For High Capacity SD Cards (> 2 GBytes), the
32-bit source address specifies the memory address in block address
format. Block length is fixed to 512 bytes as per the SD High Capacity
specification. So we need to convert the block address format
to byte address format to calculate the envaddr.
If there is no enough space for environment variables or envaddr
is larger than 4GiB, we relocate the envaddr to 0x400. The address
relocated is in the front of the first partition that is assigned
for sdboot only.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Reviewed-by: York Sun <yorksun@freescale.com>
Haijun.Zhang [Fri, 10 Jan 2014 05:52:17 +0000 (13:52 +0800)]
esdhc: Workaround for card can't be detected on T4240QDS
Card detection pin is ineffective on T4240QDS Rev1.0.
There are two cards can be connected to board.
1. eMMC card is built-in board, can not be removed. so
For eMMC card it is always there.
2. Card detecting pin is functional for SDHC card in Rev2.0.
This workaround force sdhc driver scan and initialize the card
regardless of whether the card is inserted or not in case Rev1.0.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Reviewed-by: York Sun <yorksun@freescale.com>
This patch reverts patch 'add ft_fixup_xgec to support 3rd and 4th 10GEC'.
When dual-role MAC acts as 10G,it still uses fsl,fman-port-1g-rx/tx as before.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Shengzhou Liu [Mon, 13 Jan 2014 05:01:06 +0000 (13:01 +0800)]
t2080qds/ddr: update ddr parameters
- Optimize UDIMM parameters for whole range from 1500MT/s to 2140MT/s.
- Remove unused patameters: 'cpo', 'wrdata delay', '2T', which are
unrelated to DDR3/3L.
Tested with UDIMM 9JSF25672AZ-2G1K1 and verified speed 1200/1866/2133MT/s.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Po Liu [Fri, 10 Jan 2014 02:10:59 +0000 (10:10 +0800)]
powerpc/c29xpcie: 8k page size NAND boot support base on TPL/SPL
Using the TPL/SPL method to booting from 8k page NAND flash.
- Add 256kB size SRAM tlb for second step booting;
- Add spl.c for TPL image boot;
- Add spl_minimal.c for minimal SPL image;
- Add C29XPCIE_NAND configure;
- Modify C29XPCIE.h for nand config and enviroment;
Signed-off-by: Po Liu <Po.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Po Liu [Fri, 10 Jan 2014 02:10:58 +0000 (10:10 +0800)]
powerpc:mpc85xx: Add ifc nand boot support for TPL/SPL
Using the TPL method for nand boot by sram was already
supported. Here add some code for mpc85xx ifc nand boot.
- For ifc, elbc, esdhc, espi, all need the SPL without
section .resetvec.
- Use a clear function name for nand spl boot.
- Add CONFIG_SPL_DRIVERS_MISC_SUPPORT to compile the fsl_ifc.c
in spl/Makefile;
Signed-off-by: Po Liu <Po.Liu@freescale.com> Acked-by: Scott Wood <scottwood@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
York Sun [Wed, 8 Jan 2014 21:00:42 +0000 (13:00 -0800)]
powerpc/mpc85xx: Revise workaround for DDR-A003
Existing workaround only handles one RDIMM on reference design. In case
of two RDIMMs being used, the workaround requires two separate writes to
DDR_SDRAM_MD_CNTL register.
This patch also restores two debug registers changed by the workaround.
Signed-off-by: York Sun <yorksun@freescale.com> CC: Ben Collins <ben.c@servergy.com> CC: James Yang <James.Yang@freescale.com>
projects / karo-tx-uboot.git / log