Ville Syrjälä [Wed, 22 Jun 2016 18:56:59 +0000 (21:56 +0300)]
drm/i915: Don't mark eDP encoders as MST capable
If we've determined that the encoder is eDP, we shouldn't try to use MST
on it. Or at least the code doesn't seem to expect that since there are
some type==DP checks in the MST code.
Dave Gordon [Wed, 6 Jul 2016 14:30:11 +0000 (15:30 +0100)]
drm/i915: avoid wait_for_atomic() in non-atomic host2guc_action()
Rather than using wait_for_atomic() when chacking for a response from
the GuC, we can get the effect of a hybrid spin/sleep wait by breaking
it into two stages. First, spin-wait for up to 10us to minimise latency
for "quick" commands; then, if that times out, sleep-wait for up 10ms
(the maximum allowed for a "slow" command).
Being able to do this depends on the recent patch 18f4b84 drm/i915: Use atomic waits for short non-atomic ones
and is similar to the hybrid approach in 1758b90 drm/i915: Use a hybrid scheme for fast register waits
(although we can't use that as-is, because that interface doesn't quite
match what we need here).
Chris Wilson [Wed, 6 Jul 2016 11:39:02 +0000 (12:39 +0100)]
drm/i915: Group the irq breadcrumb variables into the same cacheline
As we inspect both the tasklet (to check for an active bottom-half) and
set the irq-posted flag at the same time (both in the interrupt handler
and then in the bottom-halt), group those two together into the same
cacheline. (Not having total control over placement of the struct means
we can't guarantee the cacheline boundary, we need to align the kmalloc
and then each struct, but the grouping should help.)
v2: Try a couple of different names for the state touched by the user
interrupt handler.
Chris Wilson [Wed, 6 Jul 2016 11:39:01 +0000 (12:39 +0100)]
drm/i915: Wake up the bottom-half if we steal their interrupt
Following on from the scenario Tvrtko envisioned to explain a hard-to-hit
race with multiple first waiters, we could also then race in the
__i915_request_irq_complete() and the bottom-half may miss the vital
irq-seqno barrier and so go to sleep not noticing their seqno is
complete.
Chris Wilson [Wed, 6 Jul 2016 11:39:00 +0000 (12:39 +0100)]
drm/i915: Always double check for a missed interrupt for new bottom halves
After assigning ourselves as the new bottom-half, we must perform a
cursory check to prevent a missed interrupt. Either we miss the interrupt
whilst programming the hardware, or if there was a previous waiter (for
a later seqno) they may be woken instead of us (due to the inherent race
in the unlocked read of b->tasklet in the irq handler) and so we miss the
wake up.
Spotted-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96806 Fixes: 688e6c725816 ("drm/i915: Slaughter the thundering... herd") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1467805142-22219-1-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Tue, 5 Jul 2016 09:40:23 +0000 (10:40 +0100)]
drm/i915: Convert dev_priv->dev backpointers to dev_priv->drm
Since drm_i915_private is now a subclass of drm_device we do not need to
chase the drm_i915_private->dev backpointer and can instead simply
access drm_i915_private->drm directly.
text data bss dec hex filename 1068757 4565 416 1073738 10624a drivers/gpu/drm/i915/i915.ko 1066949 4565 416 1071930 105b3a drivers/gpu/drm/i915/i915.ko
Created by the coccinelle script:
@@
struct drm_i915_private *d;
identifier i;
@@
(
- d->dev->i
+ d->drm.i
|
- d->dev
+ &d->drm
)
and for good measure the dev_priv->dev backpointer was removed entirely.
Chris Wilson [Tue, 5 Jul 2016 09:40:21 +0000 (10:40 +0100)]
drm/i915: Remove use of dev_priv->dev backpointer in __i915_printk()
As we can just directly use drm_dev->drm.dev, we do not need the
drm_dev->dev backpointer anymore and can also loose the warning about
order of __i915_printk() and our initialisation (which is now always
safe).
Chris Wilson [Mon, 4 Jul 2016 07:48:33 +0000 (08:48 +0100)]
drm/i915: Skip capturing an error state if we already have one
As we only ever keep the first error state around, we can avoid some
work that can be quite intrusive if we don't record the error the second
time around. This does move the race whereby the user could discard one
error state as the second is being captured, but that race exists in the
current code and we hope that recapturing error state is only done for
debugging.
Note that as we discard the error state for simulated errors, igt that
exercise error capture continue to function.
Chris Wilson [Tue, 5 Jul 2016 07:54:36 +0000 (08:54 +0100)]
drm/i915: Replace lockless_dereference(bool) with READ_ONCE()
After Joonas complained about using READ_ONCE() on the only use of the
variable in the function, where the intent was to simply document that
the read was intentionally racy and unlocked, I switched the READ_ONCE()
over to lockless_dereference(). However, in linux-next that has a
stronger type-check to only allow pointers and is no longer
interchangeable with READ_ONCE(), see commit 331b6d8c7afc
("locking/barriers: Validate lockless_dereference() is used on a pointer
type")
drm/i915: Explicitly convert some macros to boolean values
Some IS_ and HAS_ macros can return any non-zero value for true.
One potential problem with that is that someone could assign
them to integers and be surprised with the result. Therefore it
is probably safer to do the conversion to 0/1 in the macros
themselves.
Luckily this does not seem to have an effect on code size.
Only one call site was getting bit by this and a patch for
that has been sent as "drm/i915/guc: Protect against HAS_GUC_*
returning true values other than one".
v2: Added some extra braces as suggested by checkpatch.
Chris Wilson [Mon, 4 Jul 2016 10:34:36 +0000 (11:34 +0100)]
drm/i915: Mass convert dev->dev_private to to_i915(dev)
Since we now subclass struct drm_device, we can save pointer dances by
noting the equivalence of struct drm_device and struct drm_i915_private,
i.e. by using to_i915().
text data bss dec hex filename 1073824 4562 416 1078802 107612 drivers/gpu/drm/i915/i915.ko 1068976 4562 416 1073954 106322 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Fri, 17 Jun 2016 13:35:05 +0000 (14:35 +0100)]
drm/i915: Limit i915_ring_test_irq debugfs to actual rings
For simplicity in testing, only report known rings in the mask. This
allows userspace to try and trigger a missed irq on every ring and do a
comparison between i915_ring_test_irq and i915_ring_missed_irq to see if
any rings failed.
v2: Move the debug message to after the rings are selected (so that the
message accurately reflects reality)
Chris Wilson [Sun, 3 Jul 2016 17:29:33 +0000 (18:29 +0100)]
drm/i915: Hold irq uncore.lock when initialising fw_domains
Acquiring the forcewake domain asserts that it is in an atomic section
(as we always expect to be under the uncore.lock). This is true except for
initialising the domains on Ivybridge, and so we generate a warning.
Wrap the manual usage of fw_domains inside the spin_lock.
Chris Wilson [Mon, 4 Jul 2016 07:08:39 +0000 (08:08 +0100)]
drm/i915: Allow userspace to request no-error-capture upon GPU hangs
igt likes to inject GPU hangs into its command streams. However, as we
expect these hangs, we don't actually want them recorded in the dmesg
output or stored in the i915_error_state (usually). To accommodate this
allow userspace to set a flag on the context that any hang emanating
from that context will not be recorded. We still do the error capture
(otherwise how do we find the guilty context and know its intent?) as
part of the reason for random GPU hang injection is to exercise the race
conditions between the error capture and normal execution.
v2: Split out the request->ringbuf error capture changes.
v3: Move the flag defines next to the intel_context->flags definition
Chris Wilson [Mon, 4 Jul 2016 07:08:38 +0000 (08:08 +0100)]
drm/i915: Record the ringbuffer associated with the request
The request tells us where to read the ringbuf from, so use that
information to simplify the error capture. If no request was active at
the time of the hang, the ring is idle and there is no information
inside the ring pertaining to the hang.
Note carefully that this will reduce the amount of information stored in
the error state - any ring without an active request will not be
recorded.
Chris Wilson [Mon, 4 Jul 2016 07:08:37 +0000 (08:08 +0100)]
drm/i915: Remove stop-rings debugfs interface
Now that we have (near) universal GPU recovery code, we can inject a
real hang from userspace and not need any fakery. Not only does this
mean that the testing is far more realistic, but we can simplify the
kernel in the process.
Chris Wilson [Mon, 4 Jul 2016 07:08:36 +0000 (08:08 +0100)]
drm/i915: Flush the RPS bottom-half when the GPU idles
Make sure that the RPS bottom-half is flushed before we set the idle
frequency when we decide the GPU is idle. This should prevent any races
with the bottom-half and setting the idle frequency, and ensures that
the bottom-half is bounded by the GPU's rpm reference taken for when it
is active (i.e. between gen6_rps_busy() and gen6_rps_idle()).
v2: Avoid recursively using the i915->wq - RPS does not touch the
struct_mutex so has no place being on the ordered i915->wq.
v3: Enable/disable interrupts for RPS busy/idle in order to prevent
further HW access from RPS outside of the wakeref.
Chris Wilson [Mon, 4 Jul 2016 07:08:35 +0000 (08:08 +0100)]
drm/i915: Add background commentary to "waitboosting"
Describe the intent of boosting the GPU frequency to maximum before
waiting on the GPU.
RPS waitboosting was introduced with commit b29c19b64528 ("drm/i915:
Boost RPS frequency for CPU stalls") but lacked a concise comment in the
code to explain itself.
Chris Wilson [Mon, 4 Jul 2016 07:08:34 +0000 (08:08 +0100)]
drm/i915: Restore waitboost credit to the synchronous waiter
Ideally, we want to automagically have the GPU respond to the
instantaneous load by reclocking itself. However, reclocking occurs
relatively slowly, and to the client waiting for a result from the GPU,
too late. To compensate and reduce the client latency, we allow the
first wait from a client to boost the GPU clocks to maximum. This
overcomes the lag in autoreclocking, at the expense of forcing the GPU
clocks too high. So to offset the excessive power usage, we currently
allow a client to only boost the clocks once before we detect the GPU
is idle again. This works reasonably for say the first frame in a
benchmark, but for many more synchronous workloads (like OpenCL) we find
the GPU clocks remain too low. By noting a wait which would idle the GPU
(i.e. we just waited upon the last known request), we can give that
client the idle boost credit (for their next wait) without the 100ms
delay required for us to detect the GPU idle state. The intention is to
boost clients that are stalling in the process of feeding the GPU more
work (and who in doing so let the GPU idle), without granting boost
credits to clients that are throttling themselves (such as compositors).
Chris Wilson [Mon, 4 Jul 2016 07:08:33 +0000 (08:08 +0100)]
drm/i915: Remove redundant queue_delayed_work() from throttle ioctl
We know, by design, that whilst the GPU is active (and thus we are
throttling) the retire_worker is queued. Therefore attempting to requeue
it with queue_delayed_work() is a no-op and we can safely remove it.
Chris Wilson [Mon, 4 Jul 2016 07:08:32 +0000 (08:08 +0100)]
drm/i915: Do not keep postponing the idle-work
Rather than persistently postponing the idle-work everytime somebody
calls i915_gem_retire_requests() (potentially ensuring that we never
reach the idle state), queue the work the first time we detect all
requests are complete. Then if in 100ms, more requests have been queued,
we will abort the idle-worker and wait again until all the new requests
have been completed.
Of course, this does depend upon the idle worker cancelling itself
gracefully from the previous patch.
Chris Wilson [Mon, 4 Jul 2016 07:08:31 +0000 (08:08 +0100)]
drm/i915: Only start retire worker when idle
The retire worker is a low frequency task that makes sure we retire
outstanding requests if userspace is being lax. We only need to start it
once as it remains active until the GPU is idle, so do a cheap test
before the more expensive queue_work(). A consequence of this is that we
need correct locking in the worker to make the hot path of request
submission cheap. To keep the symmetry and keep hangcheck strictly bound
by the GPU's wakelock, we move the cancel_sync(hangcheck) to the idle
worker before dropping the wakelock.
v2: Guard against RCU fouling the breadcrumbs bottom-half whilst we kick
the waiter.
v3: Remove the wakeref assertion squelching (now we hold a wakeref for
the hangcheck, any rpm error there is genuine).
v4: To prevent excess work when retiring requests, we split the busy
flag into two, a boolean to denote whether we hold the wakeref and a
bitmask of active engines.
v5: Reorder cancelling hangcheck upon idling to avoid a race where we
might cancel a hangcheck after being preempted by a new task
Chris Wilson [Sat, 2 Jul 2016 14:36:02 +0000 (15:36 +0100)]
drm/i915: Match bitmask size to types in intel_fb_initial_config()
smatch complains of:
drivers/gpu/drm/i915/intel_fbdev.c:403
intel_fb_initial_config() warn: should '1 << i' be a 64 bit type?
drivers/gpu/drm/i915/intel_fbdev.c:422 intel_fb_initial_config() warn:
should '1 << i' be a 64 bit type?
drivers/gpu/drm/i915/intel_fbdev.c:501 intel_fb_initial_config() warn:
should '1 << i' be a 64 bit type?
We are prepared to iterate over a u64 but don't limit the number of
connectors we try to configure to a maximum of 64.
Chris Wilson [Fri, 1 Jul 2016 16:23:29 +0000 (17:23 +0100)]
drm/i915: Remove debug noise on detecting fault-injection of missed interrupts
Since the tests can and do explicitly check debugfs/i915_ring_missed_irqs
for the handling of a "missed interrupt", adding it to the dmesg at INFO
is just noise. When it happens for real, we still class it as an ERROR.
Note that I have chose to remove it entirely because when we detect the
"missed interrupt" is irrelevant and the message contains no more
information than we glean from looking in debugfs.
Chris Wilson [Fri, 1 Jul 2016 16:23:28 +0000 (17:23 +0100)]
drm/i915: Simplify enabling user-interrupts with L3-remapping
Borrow the idea from intel_lrc.c to precompute the mask of interrupts we
wish to always enable to avoid having lots of conditionals inside the
interrupt enabling.
Chris Wilson [Fri, 1 Jul 2016 16:23:27 +0000 (17:23 +0100)]
drm/i915: Move the get/put irq locking into the caller
With only a single callsite for intel_engine_cs->irq_get and ->irq_put,
we can reduce the code size by moving the common preamble into the
caller, and we can also eliminate the reference counting.
For completeness, as we are no longer doing reference counting on irq,
rename the get/put vfunctions to enable/disable respectively and are
able to review the use of posting reads. We only require the
serialisation with hardware when enabling the interrupt (i.e. so we
cannot miss an interrupt by going to sleep before the hardware truly
enables it).
Chris Wilson [Fri, 1 Jul 2016 16:23:26 +0000 (17:23 +0100)]
drm/i915: Embed signaling node into the GEM request
Under the assumption that enabling signaling will be a frequent
operation, lets preallocate our attachments for signaling inside the
(rather large) request struct (and so benefiting from the slab cache).
v2: Convert from void * to more meaningful names and types.
Chris Wilson [Fri, 1 Jul 2016 16:23:25 +0000 (17:23 +0100)]
drm/i915: Convert trace-irq to the breadcrumb waiter
If we convert the tracing over from direct use of ring->irq_get() and
over to the breadcrumb infrastructure, we only have a single user of the
ring->irq_get and so we will be able to simplify the driver routines
(eliminating the redundant validation and irq refcounting).
Process context is preferred over softirq (or even hardirq) for a couple
of reasons:
- we already utilize process context to have fast wakeup of a single
client (i.e. the client waiting for the GPU inspects the seqno for
itself following an interrupt to avoid the overhead of a context
switch before it returns to userspace)
- engine->irq_seqno() is not suitable for use from an softirq/hardirq
context as we may require long waits (100-250us) to ensure the seqno
write is posted before we read it from the CPU
A signaling framework is a requirement for enabling dma-fences.
v2: Move to a signaling framework based upon the waiter.
v3: Track the first-signal to avoid having to walk the rbtree everytime.
v4: Mark the signaler thread as RT priority to reduce latency in the
indirect wakeups.
v5: Make failure to allocate the thread fatal.
v6: Rename kthreads to i915/signal:%u
Chris Wilson [Fri, 1 Jul 2016 16:23:24 +0000 (17:23 +0100)]
drm/i915: Stop setting wraparound seqno on initialisation
We have testcases to ensure that seqno wraparound works fine, so we can
forgo forcing everyone to encounter seqno wraparound during early
uptime. seqno wraparound incurs a full GPU stall so not forcing it
will eliminate one jitter from the early system. Using the testcases, we
have very deterministic testing which given how difficult it would be to
debug an issue (GPU hang) stemming from a wraparound using pure
postmortem analysis I see no value in forcing a wrap during boot.
Advancing the global next_seqno after a GPU reset is equally pointless.
Chris Wilson [Fri, 1 Jul 2016 16:23:23 +0000 (17:23 +0100)]
drm/i915: Only apply one barrier after a breadcrumb interrupt is posted
If we flag the seqno as potentially stale upon receiving an interrupt,
we can use that information to reduce the frequency that we apply the
heavyweight coherent seqno read (i.e. if we wake up a chain of waiters).
v2: Use cmpxchg to replace READ_ONCE/WRITE_ONCE for more explicit
control of the ordering wrt to interrupt generation and interrupt
checking in the bottom-half.
Chris Wilson [Fri, 1 Jul 2016 16:23:22 +0000 (17:23 +0100)]
drm/i915: Check the CPU cached value in HWS of seqno after waking the waiter
If we have multiple waiters, we may find that many complete on the same
wake up. If we first inspect the seqno from the CPU cache, we may reduce
the number of heavyweight coherent seqno reads we require.
Chris Wilson [Fri, 1 Jul 2016 16:23:21 +0000 (17:23 +0100)]
drm/i915: Add a delay between interrupt and inspecting the final seqno (ilk)
On Ironlake, there is no command nor register to ensure that the write
from a MI_STORE command is completed (and coherent on the CPU) before the
command parser continues. This means that the ordering between the seqno
write and the subsequent user interrupt is undefined (like gen6+). So to
ensure that the seqno write is completed after the final user interrupt
we need to delay the read sufficiently to allow the write to complete.
This delay is undefined by the bspec, and empirically requires 75us even
though a register read combined with a clflush is less than 500ns. Hence,
the delay is due to an on-chip buffer rather than the latency of the write
to memory.
Note that the render ring controls this by filling the PIPE_CONTROL fifo
with stalling commands that force the earliest pipe-control with the
seqno to be completed before the command parser continues. Given that we
need a barrier operation for BSD, we may as well forgo the extra
per-batch latency by using a common per-interrupt barrier.
Studying the impact of adding the usleep shows that in both sequences of
and individual synchronous no-op batches is negligible for the media
engine (where the write now is unordered with the interrupt). Converting
the render engine over from the current glutton of pie-controls over to
the per-interrupt delays speeds up both the sequential and individual
synchronous no-ops by 20% and 60%, respectively. This speed up holds
even when looking at the throughput of small copies (4KiB->4MiB), both
serial and synchronous, by about 20%. This is because despite adding a
significant delay to the interrupt, in all likelihood we will see the
seqno write without having to apply the barrier (only in the rare corner
cases where the write is delayed on the last required is the delay
necessary).
Chris Wilson [Fri, 1 Jul 2016 16:23:20 +0000 (17:23 +0100)]
drm/i915: Refactor scratch object allocation for gen2 w/a buffer
The gen2 w/a buffer is stuffed into the same slot as the gen5+ scratch
buffer. If we pass in the size we want to allocate for the scratch
buffer, both callers can use the same routine.
Chris Wilson [Fri, 1 Jul 2016 16:23:18 +0000 (17:23 +0100)]
drm/i915: Stop mapping the scratch page into CPU space
After the elimination of using the scratch page for Ironlake's
breadcrumb, we no longer need to kmap the object. We therefore can move
it into the high unmappable space and do not need to force the object to
be coherent (i.e. snooped on !llc platforms).
Chris Wilson [Fri, 1 Jul 2016 16:23:17 +0000 (17:23 +0100)]
drm/i915: Use HWS for seqno tracking everywhere
By using the same address for storing the HWS on every platform, we can
remove the platform specific vfuncs and reduce the get-seqno routine to
a single read of a cached memory location.
v2: Fix semaphore_passed() to look at the signaling engine (not the
waiter's)
Chris Wilson [Fri, 1 Jul 2016 16:23:16 +0000 (17:23 +0100)]
drm/i915: Spin after waking up for an interrupt
When waiting for an interrupt (waiting for the engine to complete some
work), we know we are the only waiter to be woken on this engine. We also
know when the GPU has nearly completed our request (or at least started
processing it), so after being woken and we detect that the GPU is
active and working on our request, allow us the bottom-half (the first
waiter who wakes up to handle checking the seqno after the interrupt) to
spin for a very short while to reduce client latencies.
The impact is minimal, there was an improvement to the realtime-vs-many
clients case, but exporting the function proves useful later. However,
it is tempting to adjust irq_seqno_barrier to include the spin. The
problem is first ensuring that the "start-of-request" seqno is coherent
as we use that as our basis for judging when it is ok to spin. If we
could, spinning there could dramatically shorten some sleeps, and allow
us to make the barriers more conservative to handle missed seqno writes
on more platforms (all gen7+ are known to have the occasional issue, at
least).
Chris Wilson [Fri, 1 Jul 2016 16:23:15 +0000 (17:23 +0100)]
drm/i915: Slaughter the thundering i915_wait_request herd
One particularly stressful scenario consists of many independent tasks
all competing for GPU time and waiting upon the results (e.g. realtime
transcoding of many, many streams). One bottleneck in particular is that
each client waits on its own results, but every client is woken up after
every batchbuffer - hence the thunder of hooves as then every client must
do its heavyweight dance to read a coherent seqno to see if it is the
lucky one.
Ideally, we only want one client to wake up after the interrupt and
check its request for completion. Since the requests must retire in
order, we can select the first client on the oldest request to be woken.
Once that client has completed his wait, we can then wake up the
next client and so on. However, all clients then incur latency as every
process in the chain may be delayed for scheduling - this may also then
cause some priority inversion. To reduce the latency, when a client
is added or removed from the list, we scan the tree for completed
seqno and wake up all the completed waiters in parallel.
Using igt/benchmarks/gem_latency, we can demonstrate this effect. The
benchmark measures the number of GPU cycles between completion of a
batch and the client waking up from a call to wait-ioctl. With many
concurrent waiters, with each on a different request, we observe that
the wakeup latency before the patch scales nearly linearly with the
number of waiters (before external factors kick in making the scaling much
worse). After applying the patch, we can see that only the single waiter
for the request is being woken up, providing a constant wakeup latency
for every operation. However, the situation is not quite as rosy for
many waiters on the same request, though to the best of my knowledge this
is much less likely in practice. Here, we can observe that the
concurrent waiters incur extra latency from being woken up by the
solitary bottom-half, rather than directly by the interrupt. This
appears to be scheduler induced (having discounted adverse effects from
having a rbtree walk/erase in the wakeup path), each additional
wake_up_process() costs approximately 1us on big core. Another effect of
performing the secondary wakeups from the first bottom-half is the
incurred delay this imposes on high priority threads - rather than
immediately returning to userspace and leaving the interrupt handler to
wake the others.
To offset the delay incurred with additional waiters on a request, we
could use a hybrid scheme that did a quick read in the interrupt handler
and dequeued all the completed waiters (incurring the overhead in the
interrupt handler, not the best plan either as we then incur GPU
submission latency) but we would still have to wake up the bottom-half
every time to do the heavyweight slow read. Or we could only kick the
waiters on the seqno with the same priority as the current task (i.e. in
the realtime waiter scenario, only it is woken up immediately by the
interrupt and simply queues the next waiter before returning to userspace,
minimising its delay at the expense of the chain, and also reducing
contention on its scheduler runqueue). This is effective at avoid long
pauses in the interrupt handler and at avoiding the extra latency in
realtime/high-priority waiters.
v2: Convert from a kworker per engine into a dedicated kthread for the
bottom-half.
v3: Rename request members and tweak comments.
v4: Use a per-engine spinlock in the breadcrumbs bottom-half.
v5: Fix race in locklessly checking waiter status and kicking the task on
adding a new waiter.
v6: Fix deciding when to force the timer to hide missing interrupts.
v7: Move the bottom-half from the kthread to the first client process.
v8: Reword a few comments
v9: Break the busy loop when the interrupt is unmasked or has fired.
v10: Comments, unnecessary churn, better debugging from Tvrtko
v11: Wake all completed waiters on removing the current bottom-half to
reduce the latency of waking up a herd of clients all waiting on the
same request.
v12: Rearrange missed-interrupt fault injection so that it works with
igt/drv_missed_irq_hang
v13: Rename intel_breadcrumb and friends to intel_wait in preparation
for signal handling.
v14: RCU commentary, assert_spin_locked
v15: Hide BUG_ON behind the compiler; report on gem_latency findings.
v16: Sort seqno-groups by priority so that first-waiter has the highest
task priority (and so avoid priority inversion).
v17: Add waiters to post-mortem GPU hang state.
v18: Return early for a completed wait after acquiring the spinlock.
Avoids adding ourselves to the tree if the is already complete, and
skips the awkward question of why we don't do completion wakeups for
waits earlier than or equal to ourselves.
v19: Prepare for init_breadcrumbs to fail. Later patches may want to
allocate during init, so be prepared to propagate back the error code.
Testcase: igt/gem_concurrent_blit
Testcase: igt/benchmarks/gem_latency Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: "Rogozhkin, Dmitry V" <dmitry.v.rogozhkin@intel.com> Cc: "Gong, Zhipeng" <zhipeng.gong@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Dave Gordon <david.s.gordon@intel.com> Cc: "Goel, Akash" <akash.goel@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> #v18 Link: http://patchwork.freedesktop.org/patch/msgid/1467390209-3576-6-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Fri, 1 Jul 2016 16:23:14 +0000 (17:23 +0100)]
drm/i915: Separate GPU hang waitqueue from advance
Currently __i915_wait_request uses a per-engine wait_queue_t for the dual
purpose of waking after the GPU advances or for waking after an error.
In the future, we may add even more wake sources and require greater
separation, but for now we can conceptually simplify wakeups by separating
the two sources. In particular, this allows us to use different wait-queues
(e.g. one on the engine advancement, a global one for errors and one on
each requests) without any hassle.
Chris Wilson [Fri, 1 Jul 2016 16:23:12 +0000 (17:23 +0100)]
drm/i915: Remove the dedicated hangcheck workqueue
The queue only ever contains at most one item and has no special flags.
It is just a very simple wrapper around the system-wq - a complication
with no benefits.
v2: Use the system_long_wq as we may wish to capture the error state
after detecting the hang - which may take a bit of time.
Chris Wilson [Fri, 1 Jul 2016 16:23:11 +0000 (17:23 +0100)]
drm/i915: Delay queuing hangcheck to wait-request
We can forgo queuing the hangcheck from the start of every request to
until we wait upon a request. This reduces the overhead of every
request, but may increase the latency of detecting a hang. However, if
nothing every waits upon a hang, did it ever hang? It also improves the
robustness of the wait-request by ensuring that the hangchecker is
indeed running before we sleep indefinitely (and thereby ensuring that
we never actually sleep forever waiting for a dead GPU).
As pointed out by Tvrtko, it is possible for a GPU hang to go unnoticed
for as long as nobody is waiting for the GPU. Though this rare, during
that time we may be consuming more power than if we had promptly
recovered, and in the most extreme case we may exhaust all memory before
forcing the hangcheck. Something to be wary off in future.
Chris Wilson [Fri, 1 Jul 2016 16:23:10 +0000 (17:23 +0100)]
drm/i915/shrinker: Flush active on objects before counting
As we inspect obj->active to decide how many objects we can shrink (we
only shrink idle objects), it helps to flush the active lists first
in order to have a more accurate count of available objects.
Pooled EU is a bxt only feature and kernel changes are already merged. This
feature is not yet exposed to userspace as the support was not yet
available. Beignet team expressed interest and added patches to use this.
Since we now have a user and patches to use them, expose them from the
kernel side as well.
Cc: Winiarski, Michal <michal.winiarski@intel.com> Cc: Zou, Nanhai <nanhai.zou@intel.com> Cc: Yang, Rong R <rong.r.yang@intel.com> Cc: Tim Gore <tim.gore@intel.com> Cc: Jeff McGee <jeff.mcgee@intel.com> Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com> Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1467369782-25992-1-git-send-email-arun.siluvery@linux.intel.com Acked-by: Jani Nikula <jani.nikula@intel.com>
Imre Deak [Wed, 29 Jun 2016 16:13:55 +0000 (19:13 +0300)]
drm/i915/bxt: Fix sanity check for BIOS RC6 setup
BXT BIOS has two options related to GPU power management: "RC6(Render
Standby)" and "GT PM Support". The assumption so far was that disabling
either of these options would leave RC6 uninitialized. According to my
tests this isn't so: for a proper RC6 setup we only need the "GT PM
Support" option to be enabled while the "RC6" option only controls
whether RC6 is left enabled or not by BIOS. OTOH we were missing a few
checks to ensure a proper RC6 setup. Add these now and don't fail the
sanity check if RC6 is disabled. This fixes a problem where RC6 remains
disabled after reloading the driver, since we explicitly disable RC6
during unloading.
v2:
- Print a debug message about the BIOS enabled RC state. (Sagar)
Chris Wilson [Fri, 1 Jul 2016 08:18:12 +0000 (09:18 +0100)]
drm/i915/ringbuffer: Move all generic engine->dispatch_batchbuffer together
Consolidate the block of default vfuncs for dispatching the batchbuffer.
Just a minor tweak on top of Tvrtko's great job of tidying up the vfunc
initialisation.
Introduce a function which initializes vfuncs mostly common
across engines and move write_tail initialization in it since
only one engine overrides the default.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Chris Wilson [Thu, 30 Jun 2016 14:33:36 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:44 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:45 +0000 (15:33 +0100)]
drm/i915: Perform Sandybridge BSD tail write under the forcewake
Since we have a sequence of register reads and writes, we can reduce the
latency of starting the BSD ring by performing all the mmio operations
under the same forcewake wakeref.
Chris Wilson [Thu, 30 Jun 2016 14:33:43 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:42 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:41 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:40 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:39 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:38 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:37 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:35 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:34 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:33 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:32 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:31 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:30 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:29 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:28 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:27 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:26 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:25 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Chris Wilson [Thu, 30 Jun 2016 14:33:24 +0000 (15:33 +0100)]
drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename 1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko 1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko