The SNDRV_HDSPM_IOCTL_GET_CONFIG_INFO ioctl in hdspm.c allow unprivileged
users to read uninitialized kernel stack memory, because several fields
of the hdspm_config struct declared on the stack are not altered
or zeroed before being copied back to the user. This patch takes care
of it.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adrian Knoth [Wed, 23 Feb 2011 10:43:13 +0000 (11:43 +0100)]
ALSA: hdspm - fix sync check on AES32
Fredrik Lingvall <fredrik.lingvall@gmail.com> has discovered wrong
frequency and sync detection on AES32. According to him, the provided
patch fixes these issues.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adrian Knoth [Wed, 23 Feb 2011 10:43:12 +0000 (11:43 +0100)]
ALSA: hdspm - Remove input selector on MADIface
In contrast to the RME MADI card, coax/optical selection on the MADIface
is done via a physical switch located at the breakout box. Obviously,
the driver cannot switch ports in software.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adrian Knoth [Wed, 23 Feb 2011 10:43:10 +0000 (11:43 +0100)]
ALSA: hdspm - Restrict channel count on RME AES/AES32
Without calling an appropriate rule, AES/AES32 cards would announce a
theoretical channel count of 64 (HDSPM_MAX_CHANNELS), leading to the
already known bug:
We already have all the right values in place, we simply have to inform
the upper layers about this restriction.
Note that snd_hdspm_hw_rule_rate_out_channels and
snd_hdspm_hw_rule_rate_in_channels must not be called on AES32, because
the channel count is always 16, no matter of the samplerate in use.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adrian Knoth [Wed, 23 Feb 2011 10:43:09 +0000 (11:43 +0100)]
ALSA: hdspm - Fix buffer handling on RME MADI/MADIface/AES(32)
Only RayDAT and AIO provide sane buffer pointers that can be used with
HDSPM_BufferPositionMask, on all other cards, this would result in a
wrong HW pointer leading to xruns and these messages:
On RME AES and AES(32), none of the required information
(max_channels_in, max_channels_out, channel mappings, port names) was
set, leading to the BUG below.
This patch adds the missing bits, thus fixing the bug.
Takashi Iwai [Tue, 22 Feb 2011 09:21:18 +0000 (10:21 +0100)]
ALSA: usb-audio: fix oops due to cleanup race when disconnecting
When a USB audio device is disconnected, snd_usb_audio_disconnect()
kills all audio URBs. At the same time, the application, after being
notified of the disconnection, might close the device, in which case
ALSA calls the .hw_free callback, which should free the URBs too.
Commit de1b8b93a0ba "[ALSA] Fix hang-up at disconnection of usb-audio"
prevented snd_usb_hw_free() from freeing the URBs to avoid a hang that
resulted from this race, but this introduced another race because the
URB callbacks could now be executed after snd_usb_hw_free() has
returned, and try to access already freed data.
Fix the first race by introducing a mutex to serialize the disconnect
callback and all PCM callbacks that manage URBs (hw_free and hw_params).
Reported-and-tested-by: Pierre-Louis Bossart <pierre-louis.bossart@intel.com> Cc: <stable@kernel.org>
[CL: also serialize hw_params callback] Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA: HDA: Conexant auto: Handle multiple connections to ADC node
Conexant 20641 has several inputs to its ADC node, with one selector
and individual amps for all inputs. This patch adds support in the
Conexant auto parser to handle that case.
It also means that the pin node's volume is being renamed to "Boost"
to avoid name clash with the new volume controls on the ADC node.
BugLink: http://bugs.launchpad.net/bugs/719524 Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Andreas Mohr [Fri, 18 Feb 2011 23:49:48 +0000 (00:49 +0100)]
ALSA: azt3328: hook up new emulated AC97 on AC97 patch side
Make newly created AC97 emulation of azt3328 known to the AC97 layer
side.
- relocate common functions to the top (due to definition after use)
- rename control names
- adjust 3D settings to the card's custom layout of this register
Signed-off-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Andreas Mohr [Fri, 18 Feb 2011 23:49:32 +0000 (00:49 +0100)]
ALSA: azt3328: add custom AC97 semi-emulation use standard ALSA AC97 layer
Make use of the very flexible ALSA ac97 layer (hooks for custom I/O!)
on this weird AC97 copycat hardware,
via semi-extended I/O translation/emulation.
Some 5kB binary/loaded size saved (well... additional huge AC97 module
penalty not factored in, of course ;-P).
Given that the driver previously had 20kB that's not bad,
but the much more important thing is to have AC97 layer stress-tested
with a thoroughly weird AC97 copycat (or, simply put, if it were not for
this AC97 test aspect, this effort would merely have been a nut job ;).
Signed-off-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mark Brown [Fri, 18 Feb 2011 00:35:55 +0000 (16:35 -0800)]
ASoC: Allow GPIO jack detection to be configured as a wake source
Some systems wish to use jacks as wake sources. Provide a wake flag in the
GPIO configuration which causes the driver to enable the IRQ as a wake
source.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Vinod Koul [Tue, 15 Feb 2011 12:58:54 +0000 (18:28 +0530)]
ASoC: sst_platform: fix the pulseaudio error
Pulseaudio doesnt work with current driver and it was root caused to absense of
hw_params function and malloc_pages in it.
This patch adds this and allows pa to work fine with these drivers
Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Harsha Priya <priya.harsha@intel.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Daniel Mack [Fri, 11 Feb 2011 11:08:06 +0000 (11:08 +0000)]
ALSA: usb-audio: add support for Native Instruments MK2 devices
The MK2 generation of Native Instruments' sound cards are in fact
compliant to the USB audio standard of version 2 and other approved USB
standards. However, they come up as vendor-specific device when first
connected but can be told to come up with a new set of descriptors
upon their next enumeration. The interfaces announced by the new
descriptors will be handled by the kernel's class drivers. This is done
by issuing a vendor specific device request and sending the device to
reset.
There are also some vendor-specific USB requests for some mixer elements
that can't be exported in a standard compliant way. The driver now
supports them with quirks handling mechanisms.
Signed-off-by: Daniel Mack <daniel@caiaq.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clemens Ladisch [Mon, 14 Feb 2011 10:00:47 +0000 (11:00 +0100)]
ALSA: core: sparse cleanups
Change the core code where sparse complains. In most cases, this means
just adding annotations to confirm that we indeed want to do the dirty
things we're doing.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mark Brown [Fri, 11 Feb 2011 14:39:13 +0000 (14:39 +0000)]
ASoC: Warn if WM8903 platform data is used to enable microphone IRQ
The WM8903 interrupts are clear on read so if the WM8903 detection is
enabled from platform data when the IRQ is in use (rather than using a
direct signal from a GPIO) status may be lost during startup. Help users
spot this misconfiguration by adding a WARN_ON().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Stephen Warren [Thu, 10 Feb 2011 22:37:18 +0000 (15:37 -0700)]
ASoC: Tegra: Harmony: Explicitly set mic enables
Harmony has both an external mic (a regular mic jack) and an internal mic
(a 0.1" two-pin header on the board).
The external mic is connected to the WM8903's IN1L pin, and is supported
by the current driver.
The internal mic is connected to the WM8903's IN1R pin, and is not supported
by the current driver.
It appears that no Harmony systems were shipped with any internal mic
connected; users were expected to provide their own. This makes the
internal mic connection less interesting.
The WM8903's Mic Bias signal is used for both of these mics. For each mic,
a GPIO drives a transistor which gates whether the mic bias signal is
actively connected to that mic, or isolated from it.
The dual use of the mic bias for both mics makes a general-purpose complete
implementation of mic detection using the mic bias complex. So, for
simplicity, the internal mic is currently ignored by the driver.
This patch configures the relevant GPIOs to enable the mic bias connection
to the external mic, and disable the mic bias connection to the internal
mic. Note that in practice, this is the default state if these GPIOs aren't
configured.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Fri, 11 Feb 2011 11:42:19 +0000 (11:42 +0000)]
ASoC: Ensure supplies are maintained for force enabled widgets
If a widget has been force enabled then not only do we need to keep the
widget itself enabled, we also need to keep any supplies the widget
requires enabled. The user could force all the individual widgets on but
this requires too much knowledge of device internals.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Tested-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
ASoC: WM8994: Improve robustness in some use cases
Ensure that on disabling certain registers such as AIF1DAC1L,
AIF1DAC1R etc. the AIF1CLK and AIF2CLK remain enabled. Similarly
when enabling those registers, AIF1CLK and AIF2CLK will remain
disabled.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
Stephen Warren [Thu, 10 Feb 2011 22:37:14 +0000 (15:37 -0700)]
ASoC: WM8903: Fix mic detection enable logic
The mic detection HW should be enabled when either mic or short detection
is required, not when only both are required.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
Stephen Warren [Thu, 10 Feb 2011 22:37:13 +0000 (15:37 -0700)]
ASoC: WM8903: Fix mic detection register definitions
* There is no hysteresis enable field in the current datasheet.
* Mic detection threshold field is only 2 bits wide.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jarkko Nikula [Thu, 10 Feb 2011 15:22:23 +0000 (17:22 +0200)]
ASoC: Allow use sleeping gpio in soc-jack
It is safe to use sleeping gpio in snd_soc_jack_gpio_detect as it is not
called from interrupt context. This avoids WARN_ON from __gpio_get_value
if sleeping gpio is registered for jack.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Vinod Koul [Thu, 10 Feb 2011 07:28:01 +0000 (12:58 +0530)]
ASoC: mid-x86: Use the soc-jack apis for jack type detection
This patch modifies the mfld_machine to use the new jack apis for adding the
voltage zones for jack type detection. It also modifed TI sn95031 codec driver
to use these new apis
Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Harsha Priya <priya.harsha@intel.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Thu, 10 Feb 2011 14:20:49 +0000 (14:20 +0000)]
ASoC: Use explicit sequence for WM8903 bias off
This makes no real difference compared to the write sequencer sequence
that was previously used but can run without a clock being provided.
Also remove the write sequencer support code as this was the last use
of it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Thu, 10 Feb 2011 14:01:38 +0000 (14:01 +0000)]
ASoC: Don't use write sequencer to power up WM8903
The write sequencer sequencer sequence takes longer than is desirable
as it brings up a full playback path which is not required at this
point. Open coding the sequence cuts the startup time by two thirds.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Content of the CX20442's snd_soc_codec_driver.reg_cache_default pointed
area, introduced with my recent NULL pointer dereferece fix (commit f019ee5feb344ff0b22b58df4568676295aae14f), occured wrong after further
testing, more thorough than just booting successfully. There are two
problems with it:
1) It should read
(1 << CX20442_TELOUT) | (1 << CX20442_MIC),
not
CX20442_TELOUT | CX20442_MIC.
2) While correctly matching actual codec hardware state on boot when
fixed per 1), a few more code modifications would still be required
to reflect that state not only into register cache, but also force
them into DAPM pins state, otherwise an inconsitency occures which
may prevent further codec state changes from being applied correctly.
As a result, the phone stops ringing after reboot, until someone
picks up the handset for the first time.
Revert that reg_cache_default content to a working, previous de facto
default value of 0, in hope this change can still be accepted as an rc
cycle fix.
Created and tested against linux-2.6.38-rc4
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit bb758e9637e5ddc removed snd_hrtimer_callback() from the hardware
interrupt handler, thus moving it into a tasklet, but did not tell the
ALSA timer framework about this, so the timer handling would now be done
in the ALSA timer tasklet scheduled from another tasklet.
To fix this, add the flag to tell the ALSA timer framework that the
timer handler is already being invoked in a tasklet.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clemens Ladisch [Thu, 10 Feb 2011 15:15:44 +0000 (16:15 +0100)]
ALSA: hrtimer: handle delayed timer interrupts
If a timer interrupt was delayed too much, hrtimer_forward_now() will
forward the timer expiry more than once. When this happens, the
additional number of elapsed ALSA timer ticks must be passed to
snd_timer_interrupt() to prevent the ALSA timer from falling behind.
This mostly fixes MIDI slowdown problems on highly-loaded systems with
badly behaved interrupt handlers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-and-tested-by: Arthur Marsh <arthur.marsh@internode.on.net> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA: asihpi - Remove int flag polling code preparing for stream interrupts.
Interrupt flag used for message handshake will be required for
stream interrupts, so conditionally compiled code without
HPI6205_NO_HSR_POLL defined can never be used; removing it.
ALSA: asihpi - Rewrite PCM timer function. Update control names.
Reported samples_played from card may be inaccurate, so don't use it.
Update control names to be closer to alsa standard practice.
Also fixed some accidentally lowercased strings.
[Removed adriver.h inclusion for external module builds by tiwai]
Remove many unused functions.
Update some message and cache structs.
Use pci info directly from pci_dev.
Allow control cache elements with variable size, and handle
large message/response from dsp.
hpi6000 and hpi6205: fix error path when adapter bootload fails.
hpimsgx.c get rid of code duplicated in hpicmn.c
projects / karo-tx-linux.git / log