Tero Kristo [Fri, 23 Oct 2009 16:03:47 +0000 (19:03 +0300)]
OMAP2/3: DMTIMER: Clear pending interrupts when stopping a timer
OMAP GP timers keep running for a few cycles after they are stopped,
which can cause the timer to expire and generate an interrupt. The
pending interrupt will prevent e.g. OMAP from entering suspend, thus
we ack it manually. Only applicable on OMAP2/3/4.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, DSS does not wakeup when there is a DMA request. DSS wake
up event must be enabled so that the DMA request to refill the FIFO
will wake up the CORE domain.
Signed-off-by: Subramani Venkatesh <subramani.venkatesh@windriver.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Thu, 24 Sep 2009 23:35:48 +0000 (16:35 -0700)]
OMAP: timekeeping: time should not stop during suspend
During suspend, the kernel timekeeping subsystem is shut down. Before
suspend and upon resume, it uses a weak function
read_persistent_clock() to determine the amount of time that elapsed
during suspend.
This function was not implemented on OMAP, so from the timekeeping
subsystem perspective (and thus userspace as well) it appeared that no
time elapsed during suspend.
This patch uses the 32k sync timer as a the persistent clock.
NOTE: This does *NOT* fully handle wrapping of the 32k sync timer, so
more than one wrapping of the 32k sync timer during suspend may
cause problems. Also note there are not interrupts when the 32k
sync timer wraps, so something else has to be done.
Reported-by: Jon Hunter <jon-hunter@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Tero Kristo [Tue, 17 Nov 2009 16:34:53 +0000 (18:34 +0200)]
OMAP3: PM: Force write last pad config register into save area
Due to OMAP3 erratas 1.157, 1.185 the save of the last pad register
(ETK_D14 and ETK_D15) can fail sometimes when there is simultaneous
OCP access to the SCM register area. Fixed by writing the last
register to the save area.
Also, optimized the delay loop for the HW save to include an udelay(1),
which limits the number of unnecessary HW accesses to SCM register area
during the save.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com> Acked-by: Nishanth Menon <nm@ti.com> Reviewed-by: Anand Gadiyar <gadiyar@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Manjunatha GK [Mon, 16 Nov 2009 14:46:52 +0000 (20:16 +0530)]
OMAP3: PM debug: fix build error when !CONFIG_DEBUG_FS
The PM debug code fails to build on when CONFIG_DEBUG_FS is not
enabled.
Build error log:
arch/arm/mach-omap2/built-in.o: In function `omap_sram_idle':
arch/arm/mach-omap2/pm34xx.c:449: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/pm34xx.c:460: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/built-in.o: In function `configure_vc':
arch/arm/mach-omap2/pm34xx.c:1237: undefined reference to `pm_dbg_regset_init'
arch/arm/mach-omap2/pm34xx.c:1238: undefined reference to `pm_dbg_regset_init'
make: *** [.tmp_vmlinux1] Error 1
This patch fixes the above errors.
Kernel booting is tested on omap zoom2 and zoom3 boards.
Signed-off-by: Manjunatha GK <manjugk@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP3: PM: Removing redundant and potentially dangerous PRCM configration
As part of Core domain context restoration while coming out of off mode
there are some registers being restored which are not required to be restored.
ROM code will have restored them already. Overwriting some of them can have
potential side effect. Eg: CM_CLKEN_PLL register should not be written while dpll is locked.
Tested on OMAP 3430 SDP for suspend/resume and off mode with sleep_while_idle enabled.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Tero Kristo [Fri, 23 Oct 2009 16:03:50 +0000 (19:03 +0300)]
OMAP3: PM: Disable interrupt controller AUTOIDLE before WFI
OMAP interrupt controller goes to unknown state when there is right
combination of l3,l4 sleep/wake-up transitions, l4 autoidle in
interrupt controller and some interrupt. When this happens, interrupts
are not delivered to ARM anymore and ARM will remain in WFI (wait for
interrupt) until interrupt controller is forced to wake-up
(i.e. lauterbach).
Signed-off-by: Tero Kristo <tero.kristo@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Paul Walmsley [Wed, 20 Jan 2010 00:30:55 +0000 (17:30 -0700)]
OMAP1 clock: fix for "BUG: spinlock lockup on CPU#0"
Commit 52650505fbf3a6ab851c801f54e73e76c55ab8da caused clock initialization
to fail on OMAP1 with "BUG: spinlock lockup on CPU#0" -- this is because
omap1_select_table_rate() and omap1_round_to_table_rate() call clk_get_rate()
with the clockfw spinlock held. Fix by accessing the rate directly from
the internal clock framework functions.
Thanks to Tony Lindgren <tony@atomide.com> for reporting and testing the fix.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Tony Lindgren <tony@atomide.com>
Rajendra Nayak [Wed, 20 Jan 2010 00:30:55 +0000 (17:30 -0700)]
OMAP4: clocks: Fix the clksel_rate struct DPLL divs
For all DPLL's the valid dividers are same as the values
to be programmed in the register. 0 is an invalid value.
The changes are generated by updating the script which autogenerates
the file modifed in the patch.
Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Wed, 20 Jan 2010 00:30:54 +0000 (17:30 -0700)]
OMAP4: PRCM: Fix the base address for CHIRONSS reg defines
The CHIRONSS has its own local PRCM module and the register defines
need to use the CHIRONSS base and not the PRM base.
The changes are generated by updating the script which autogenerates
the file modifed in the patch.
Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tony Lindgren [Tue, 19 Jan 2010 23:15:24 +0000 (15:15 -0800)]
omap: Fix functions for dynamic remuxing of pins
Make the omap_mux_read and write available for board code,
and rename omap_mux_set_board_signals into omap_mux_write_array.
Also add the related prototypes and comments into mux.h.
In some cases we want to change the signals dynamically,
mostly for power management.
Note that we cannot use the signal names as they are set
__init to save memory.
Tony Lindgren [Wed, 20 Jan 2010 02:17:07 +0000 (18:17 -0800)]
omap: Fix cmdline muxing
Looks like cmdline muxing got broken at some point when we
decided to limit muxing to __init code. Currently omap_mux_entry
list is not yet initialized when we try to initialize cmdline
muxing.
Fix this by calling omap_mux_init_list() before calling
omap_mux_set_cmdline_signals().
Reported-by: Philip Balister <philip@balister.org> Tested-by: Philip Balister <philip@balister.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Russell King [Wed, 20 Jan 2010 00:30:52 +0000 (17:30 -0700)]
OMAP3: clock: Remove unnecessarily .init initializers from OMAP3 clocks
The first thing that omap2_init_clksel_parent() does is check for
a non-zero .clksel field in the struct clk. Therefore, it is
pointless calling this function on clocks where the clksel field
is unset.
Remove init calls to omap2_init_clksel_parent() on clocks without
a clksel field.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Thara Gopinath [Wed, 20 Jan 2010 00:30:51 +0000 (17:30 -0700)]
OMAP3: hwmod: Adding flag to prevent caching of sysconfig register.
In the current implementation the sysconfig value is read into
_sysc_cache once and an actual update to the sysconfig register
happens only if the new value paased is differnt from the one in _sysc_cache.
_sysc_cache is updated only if _HWMOD_SYSCONFIG_LOADED is not set.
This can lead to the follwing issue if off mode is enabled in modules
which employs "always-retore" mechanism of context save and restore.
a. The module sets the sysconfig register through omap_device_enable.
Here _sysc_cache is updated with the value written to the sysconfig
register and left.
b. The power domain containig the module enters off mode and the
module context is lost.
c. The module in use becomes active and calls omap_device_enable to
enable itself. Here a read of sysconfig register does not happen
as _HWMOD_SYSCONFIG_LOADED flag is set. The value to be written
to the sysconfig register will be same as the one written in step a.
Since _sysc_cache reflects the previous written value an update
of the sysconfig register does not happen.
This means in modules which employs "always-restore" mechanism
after off , the sysconfig regsiters will never get updated.
This patch introduces a flag SYSC_NO_CACHE which if set ensures that the
sysconfig register is always read into _sysc_cache before an update is
attempted.
This flags need to be set only by modules which does not do a context save
but re-initializes the registers every time the module is accessed. This
includes modules like i2c, smartreflex etc.
Signed-off-by: Thara Gopinath <thara@ti.com>
[paul@pwsan.com: tweaked to apply on a different head, added flag comment] Signed-off-by: Paul Walmsley <paul@pwsan.com>
Dave Chinner [Tue, 12 Jan 2010 06:39:16 +0000 (17:39 +1100)]
lib: Introduce generic list_sort function
There are two copies of list_sort() in the tree already, one in the DRM
code, another in ubifs. Now XFS needs this as well. Create a generic
list_sort() function from the ubifs version and convert existing users
to it so we don't end up with yet another copy in the tree.
Signed-off-by: Dave Chinner <david@fromorbit.com> Acked-by: Dave Airlie <airlied@redhat.com> Acked-by: Artem Bityutskiy <dedekind@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 13 Jan 2010 04:56:20 +0000 (20:56 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: retry link resume if necessary
ata_piix: enable 32bit PIO on SATA piix
sata_promise: don't classify overruns as HSM errors
Linus Torvalds [Wed, 13 Jan 2010 04:56:01 +0000 (20:56 -0800)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: Ensure ARMv6/7 mm files are built using appropriate assembler options
ARM: Fix wrong dmb
ARM: 5874/1: serial21285: fix disable_irq-from-interrupt-handler deadlock
ARM: 5873/1: ARM: Fix the reset logic for ARM RealView boards
ARM: 5872/1: ARM: include needed linux/cpu.h in asm/cpu.h
ARM: 5871/1: arch/arm: Fix build failure for lpd7a404_defconfig caused by missing includes
ARM: 5870/1: arch/arm: Fix build failure for defconfigs without CONFIG_ISA_DMA_API set
ARM: 5868/1: ARM: fix "BUG: using smp_processor_id() in preemptible code"
ARM: 5867/1: Update U300 defconfig
ARM: 5866/1: arm ptrace: use unsigned types for kernel pt_regs
[ARM] pxa: fix strange characters in zaurus gpio .desc
ARM: add missing recvmmsg syscall number
[ARM] pxa: fix compiler warnings of unused variable 'id' in cpu_is_pxa9*()
[ARM] pxa: update pwm_backlight->notify() to include missed 'struct device *'
[ARM] pxa: enable L2 if present in XSC3
[ARM] pxa: do not enable L2 after MMU is enabled
Linus Torvalds [Wed, 13 Jan 2010 04:54:52 +0000 (20:54 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix ALC861-VD capture source mixer
ALSA: ac97: add AC97 STMicroelectronics' codecs
ALSA: ac97: Add Dell Dimension 2400 to Headphone/Line Jack Sense blacklist
ASoC: Fix WM8350 DSP mode B configuration
sbawe: fix memory detection part 2
sound: oss: off by one bug
ALSA: usb-audio - Avoid Oops after disconnect
ALSA: test off by one in setsamplerate()
ALSA: atiixp: Specify codec for Foxconn RC4107MA-RS2
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
sky2: Fix oops in sky2_xmit_frame() after TX timeout
Documentation/3c509: document ethtool support
af_packet: Don't use skb after dev_queue_xmit()
vxge: use pci_dma_mapping_error to test return value
netfilter: ebtables: enforce CAP_NET_ADMIN
e1000e: fix and commonize code for setting the receive address registers
e1000e: e1000e_enable_tx_pkt_filtering() returns wrong value
e1000e: perform 10/100 adaptive IFS only on parts that support it
e1000e: don't accumulate PHY statistics on PHY read failure
e1000e: call pci_save_state() after pci_restore_state()
netxen: update version to 4.0.72
netxen: fix set mac addr
netxen: fix smatch warning
netxen: fix tx ring memory leak
tcp: update the netstamp_needed counter when cloning sockets
TI DaVinci EMAC: Handle emac module clock correctly.
dmfe/tulip: Let dmfe handle DM910x except for SPARC on-board chips
ixgbe: Fix compiler warning about variable being used uninitialized
netfilter: nf_ct_ftp: fix out of bounds read in update_nl_seq()
mv643xx_eth: don't include cache padding in rx desc buffer size
...
Fix trivial conflict in drivers/scsi/cxgb3i/cxgb3i_offload.c
Greg Ungerer [Wed, 13 Jan 2010 00:42:05 +0000 (10:42 +1000)]
m68knommu: fix definitions of __pa() and __va()
Fix compilation breakage of all m68knommu targets:
CC arch/m68knommu/kernel/asm-offsets.s
In file included from include/linux/sched.h:77,
from arch/m68knommu/kernel/asm-offsets.c:12:
include/linux/percpu.h: In function 'per_cpu_ptr_to_phys':
include/linux/percpu.h:161: error: implicit declaration of function 'virt_to_phy
This is broken in linux-2.6.33-rc3.
Change the definitions of __pa() and __va() to not use virt_to_phys()
and phys_to_virt(). Trivial 1:1 conversion required for the non-MMU case.
A side effect if this is that the m68knommu can now use asm/virtconvert.h
for the definition of virt_to_phys() and phys_to_virt().
Also cleaned up the definition of page_to_phys() when moving into
virtconvert.h.
Tejun Heo [Mon, 11 Jan 2010 02:14:44 +0000 (11:14 +0900)]
libata: retry link resume if necessary
Interestingly, when SIDPR is used in ata_piix, writes to DET in
SControl sometimes get ignored leading to detection failure. Update
sata_link_resume() such that it reads back SControl after clearing DET
and retry if it's not clear.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: fengxiangjun <fengxiangjun@neusoft.com> Reported-by: Jim Faulkner <jfaulkne@ccs.neu.edu> Cc: stable@kernel.org Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Mon, 11 Jan 2010 08:03:11 +0000 (17:03 +0900)]
ata_piix: enable 32bit PIO on SATA piix
Commit 871af1210f13966ab911ed2166e4ab2ce775b99d enabled 32bit PIO for
PATA piix but didn't for SATA. There's no reason not to use 32bit PIO
on SATA piix. Enable it.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_promise: don't classify overruns as HSM errors
When sata_promise encounters an overrun or underrun error it
translates that to a libata AC_ERR_HSM, causing a hard reset.
Since over/under-runs were thought to be rare and transient,
this action seemed reasonable.
Unfortunately it turns out that the controller throws overrun
errors when e.g. hal polls a CD or DVD writer containing blank
media, causing long sequences of hard resets and retries before
EH finally gives up.
This patch updates sata_promise to classify over/under-runs as
AC_ERR_OTHER instead. This allows libata EH and upper layers to
retry or fail the operation as they see fit without the disruption
caused by repeated hard resets.
This fixes a problem using a DVD-RAM drive with sata_promise,
reported by Thomas Schorpp. I also tested it on a DVD-RW drive.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Tested-by: thomas schorpp <thomas.schorpp@googlemail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Russell King [Tue, 12 Jan 2010 18:59:16 +0000 (18:59 +0000)]
ARM: Fix wrong dmb
The __kuser_cmpxchg code uses an ARMv6 dmb instruction, rather than
one based upon the architecture being built for. Switch to using
the macro provided for this purpose, which also eliminates the
need for an ifdef.
Acked-by: Nicolas Pitre <nico@fluxnic.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Anton Blanchard [Wed, 6 Jan 2010 04:55:13 +0000 (15:55 +1100)]
MIPS: cpumask_of_node() should handle -1 as a node
pcibus_to_node can return -1 if we cannot determine which node a pci bus
is on. If passed -1, cpumask_of_node will negatively index the lookup array
and pull in random data:
David VomLehn [Tue, 22 Dec 2009 01:43:42 +0000 (17:43 -0800)]
MIPS: PowerTV: Remove extra r4k_clockevent_init() call
A call to r4k_clocksource_init() was added to plat_time_init(), but
when init_mips_clock_source() calls the same function, boot fails in
clockevents_register_device(). This patch removes the extraneous call.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Patchwork: http://patchwork.linux-mips.org/patch/803/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Wed, 23 Dec 2009 21:18:54 +0000 (13:18 -0800)]
MIPS: Octeon: Add sched_clock() to csrc-octeon.c
With the advent of function graph tracing on MIPS, Octeon needs a high
precision sched_clock() implementation. Without it, most timing
numbers are reported as 0.000.
This new sched_clock just uses the 64-bit cycle counter appropriately
scaled.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/805/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Mon, 21 Dec 2009 15:48:57 +0000 (00:48 +0900)]
MIPS: TXx9: Cleanup builtin-cmdline processing
Since commit 898d357b5262f9e26bc2418e01f8676e80d9867e (lmo) / 6acc7d485c24c00e111c61b2e6dff9180faebcae (kernel.org) ("Fix and enhance
built-in kernel command line") arcs_cmdline[] does not contain built-in
command line. The commit introduce CONFIG_CMDLINE_BOOL and
CONFIG_CMDLINE_OVERRIDE to control built-in command line, and now we can
use them instead of platform-specific built-in command line processing.
Yoichi Yuasa [Fri, 18 Dec 2009 12:33:46 +0000 (21:33 +0900)]
MIPS: PowerTV: Remove mips_machine_halt()
mips_machine_halt() is same as mips_machine_restart(). Also delete the
registration of _machine_halt and pm_power_off because mips_machine_halt()
is the restart function.
Wu Zhangjin [Thu, 10 Dec 2009 14:55:13 +0000 (22:55 +0800)]
MIPS: Cleanup and Fixup of compressed kernel support
o Remove the .initrd section. The initrd section was already handled
when vmlinux was linked.
o Discard .MIPS.options, .options, .pdr, .reginfo, .comment and .note
sections. If .MIPS.options is not removed, kernels compiled with gcc
3.4.6 will not boot.
o Clean up the file format.
o Remove several other unneeded sections.
Tested with GCC 3.4.6 and 4.4.1 with and without initrd.
Takashi Iwai [Tue, 12 Jan 2010 13:00:11 +0000 (14:00 +0100)]
ALSA: hda - Fix ALC861-VD capture source mixer
The capture source or input source mixer element wasn't created properly
for ALC861-VD codec due to the wrong NID passed to
alc_auto_create_input_ctls().
Jarek Poplawski [Mon, 4 Jan 2010 08:48:41 +0000 (08:48 +0000)]
sky2: Fix oops in sky2_xmit_frame() after TX timeout
During TX timeout procedure dev could be awoken too early, e.g. by
sky2_complete_tx() called from sky2_down(). Then sky2_xmit_frame()
can run while buffers are freed causing an oops. This patch fixes it
by adding netif_device_present() test in sky2_tx_complete().
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=14925
With debugging by: Mike McCormack <mikem@ring3k.org>
Reported-by: Berck E. Nash <flyboy@gmail.com> Tested-by: Berck E. Nash <flyboy@gmail.com> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
According to Suresh, this might be an IBM platform issue, as on other
Intel platforms with <= 8 logical cpu's, logical flat mode works fine
irespective of physical apic id values (inline with the xapic
architecture).
Revert this for now because of the IBM platform breakage.
Another version will be re-submitted after the complete analysis.
Ben Hutchings [Mon, 11 Jan 2010 23:53:45 +0000 (15:53 -0800)]
Documentation/3c509: document ethtool support
3c509 was changed to support ethtool in 2002, making the 'xcvr' module
parameter obsolete in most cases. More recently 3c509 was converted
to the modern driver model and this parameter was removed. Fix the
documentation to refer to ethtool rather than the module parameter.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Sun, 10 Jan 2010 22:04:19 +0000 (22:04 +0000)]
af_packet: Don't use skb after dev_queue_xmit()
tpacket_snd() can change and kfree an skb after dev_queue_xmit(),
which is illegal.
With debugging by: Stephen Hemminger <shemminger@vyatta.com>
Reported-by: Michael Breuer <mbreuer@majjas.com>
With help from: David S. Miller <davem@davemloft.net> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Tested-by: Michael Breuer<mbreuer@majjas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 11 Jan 2010 17:48:48 +0000 (09:48 -0800)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: Ensure we force all busy extents in range to disk
xfs: Don't flush stale inodes
xfs: fix timestamp handling in xfs_setattr
xfs: use DECLARE_EVENT_CLASS
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
GFS2: Use MAX_LFS_FILESIZE for meta inode size
GFS2: Fix gfs2_xattr_acl_chmod()
GFS2: Fix locking bug in rename
GFS2: Ensure uptodate inode size when using O_APPEND
Linus Torvalds [Mon, 11 Jan 2010 17:47:52 +0000 (09:47 -0800)]
Merge branch 'agp-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6
* 'agp-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp/hp: fail gracefully if we don't find an IOC
agp/hp: fixup hp agp after ACPI changes
agp: correct missing cleanup on error in agp_add_bridge
Linus Torvalds [Mon, 11 Jan 2010 17:46:20 +0000 (09:46 -0800)]
Merge branch 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (45 commits)
drm/nv04: Fix set_operation software method.
drm/nouveau: initialise DMA tracking parameters earlier
drm/nouveau: use dma.max rather than pushbuf size for checking GET validity
drm/nv04: differentiate between nv04/nv05
drm/nouveau: Fix null deref in nouveau_fence_emit due to deleted fence
drm/nv50: prevent a possible ctxprog hang
drm/nouveau: have ttm's fault handler called directly
drm/nv50: restore correct cache1 get/put address on fifoctx load
drm/nouveau: create function for "dealing" with gpu lockup
drm/nouveau: remove unused nouveau_channel_idle() function
drm/nouveau: fix handling of fbcon colours in 8bpp
drm/nv04: Context switching fixes.
drm/nouveau: Use the software object for fencing.
drm/nouveau: Allocate a per-channel instance of NV_SW.
drm/nv50: make the blocksize depend on vram size
drm/nouveau: better alignment of bo sizes and use roundup instead of ALIGN
drm/nouveau: Don't skip card take down on nv0x.
drm/nouveau: Implement nv42-nv43 TV load detection.
drm/nouveau: Clean up the nv17-nv4x load detection code a bit.
drm/nv50: fix fillrect color
...
Avi Kivity [Sun, 10 Jan 2010 14:28:09 +0000 (16:28 +0200)]
core, x86: make LIST_POISON less deadly
The list macros use LIST_POISON1 and LIST_POISON2 as undereferencable
pointers in order to trap erronous use of freed list_heads. Unfortunately
userspace can arrange for those pointers to actually be dereferencable,
potentially turning an oops to an expolit.
To avoid this allow architectures (currently x86_64 only) to override
the default values for these pointers with truly-undereferencable values.
This is easy on x86_64 as the virtual address space is large and contains
areas that cannot be mapped.
Other 64-bit architectures will likely find similar unmapped ranges.
[ingo: switch to 0xdead000000000000 as the unmapped area]
[ingo: add comments, cleanup]
[jaswinder: eliminate sparse warnings]
David Howells [Fri, 8 Jan 2010 22:43:21 +0000 (14:43 -0800)]
mn10300: make the ASB2305's PCnet32 NIC work by using the PCI bridge's SRAM
Access to the ASB2305's PCnet32 NIC doesn't work correctly because when
the NIC attempts to update the ring buffer flags by DMA, the change to RAM
crops up about 17uS after the interrupt line is asserted. This is almost
certainly due to a bug in the PCI bridge FPGA on that board.
We can get around this by making dma_alloc_coherent() put the ring buffer
in the SRAM attached to the PCI bridge rather than in the SDRAM.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Fri, 8 Jan 2010 22:43:20 +0000 (14:43 -0800)]
mn10300: insert PCI root bus resources for the ASB2305 devel motherboard
Insert PCI root bus resources for the MN10300-based ASB2305 development
kit motherboard. This is required because the CPU's window onto the PCI
bus address space is considerably smaller than the CPU's full address
space and non-PCI devices lie outside of the PCI window that we might want
to access.
Without this patch, the PCI root bus uses the platform-level bus
resources, and these are then confined to the PCI window, thus making
platform_device_add() reject devices outside of this window.
We also add a reservation for the PCI SRAM region.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bjorn Helgaas [Fri, 8 Jan 2010 22:43:19 +0000 (14:43 -0800)]
mn10300: use generic pci_enable_resources()
Use the generic pci_enable_resources() instead of the arch-specific code.
Unlike this arch-specific code, the generic version:
- checks PCI_NUM_RESOURCES (11), not 6, resources
- skips resources that have neither IORESOURCE_IO nor IORESOURCE_MEM set
- skips ROM resources unless IORESOURCE_ROM_ENABLE is set
- checks for resource collisions with "!r->parent"
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Salter [Fri, 8 Jan 2010 22:43:16 +0000 (14:43 -0800)]
mn10300: add cc clobbers to asm statements
gcc 4.2.1 for MN10300 is more agressive than the older gcc in
reordering/moving other insns between an insn that sets flags and an insn
that uses those flags. This leads to trouble with asm statements which
are missing an explicit "cc" clobber. This patch adds the explicit "cc"
clobber to asm statements which do indeed clobber the condition flags.
Signed-off-by: Mark Salter <msalter@redhat.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Salter [Fri, 8 Jan 2010 22:43:14 +0000 (14:43 -0800)]
mn10300: signal stack fix
This fixes a signal stack handling problem in the MN10300 arch. When new
threads are cloned with CLONE_VM, they don't inherit the alternate signal
stack. They do share the signal flags, though. When deciding whether to
use an alternate stack, the arch code needs to check to make sure the task
struct contains a valid alternate stack. This patch fixes the MN10300
arch by using the sas_ss_flags() test provided by sched.h rather than the
on_sig_stack() test which is insufficient by itself.
Signed-off-by: Mark Salter <msalter@redhat.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OGAWA Hirofumi [Fri, 8 Jan 2010 22:43:11 +0000 (14:43 -0800)]
rtc_cmos: convert shutdown to new pnp_driver->shutdown
commit abd6633c67925f90775bb74755f9c547e30f1f20 ("pnp: add a shutdown
method to pnp drivers") adds shutdown method to bus driver blindly. With
it, driver->shutdown is no longer valid.
Minchan Kim [Fri, 8 Jan 2010 22:43:10 +0000 (14:43 -0800)]
smaps: fix wrong rss count
A long time ago we regarded zero page as file_rss and vm_normal_page
doesn't return NULL.
But now, we reinstated ZERO_PAGE and vm_normal_page's implementation can
return NULL in case of zero page. Also we don't count it with file_rss
any more.
Then, RSS and PSS can't be matched. For consistency, Let's ignore zero
page in smaps_pte_range.
Signed-off-by: Minchan Kim <minchan.kim@gmail.com> Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Acked-by: Hugh Dickins <hugh.dickins@tiscali.co.uk> Acked-by: Matt Mackall <mpm@selenic.com> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gpio: adp5588-gpio: new driver for ADP5588 GPIO expanders
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/cpuidle/governors/menu.c: fix undefined reference to `__udivdi3'
menu: use proper 64 bit math
The new menu governor is incorrectly doing a 64 bit divide. Compile
tested only
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Len Brown <len.brown@intel.com> Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>