Connecting two boards directly more than 2 hours, Ar8031 phy link
status generates glitch, which cause ethernet link down/up issue, but
ethernet still be active. There have three cases to validate the issue:
Item#1: If add performance stress test while runing IEEE1588, the link
down/up issue cannot be found.
Item#2: If insert switch between two net nodes and run IEEE1588 test,
the issue also cannot be found.
Item#3: If disable AR8031 SmartEEE feature, after two days overnight test,
no such issue found.
The issue is caused by phy Ar8031 SmartEEE feature, Item#1 and Item#2 can
prevent phy enter lpm mode, which match the Item#3 test result, so disable
SmartEEE feature to avoid the link issue generation.
Current driver only do phy reset in probe function, which is
not right. Since some phy clock is disabled after module probe,
the phy enter abnormal status, which needs do reset to recovery
the phy. And do ifconfig ethx up/down test, the phy also enter
abnormal status.
The log as:
libphy: 2188000.ethernet:04 - Link is Up - 10/Full
libphy: 2188000.ethernet:04 - Link is Up - 100/Full
libphy: 2188000.ethernet:04 - Link is Down
libphy: 2188000.ethernet:04 - Link is Up - 10/Half
libphy: 2188000.ethernet:04 - Link is Up - 10/Full
libphy: 2188000.ethernet:04 - Link is Up - 100/Full
...
So, do phy reset if ethx up/down or do clock enable/disable
operation.
Shengjiu Wang [Fri, 9 Aug 2013 06:45:51 +0000 (14:45 +0800)]
ENGR00274585-9 ASoC: change error message to debug message
This error message is not actual error, which is a warning. When using
FE/BE, if there is widget which is used by playback and capture route, then
this message will be printed.
Signed-off-by: Shengjiu Wang <b02247@freescale.com>
Robby Cai [Thu, 8 Aug 2013 03:23:54 +0000 (11:23 +0800)]
ENGR00274412-1 dma: pxp: Port ePxP driver to 3.10
It's ported from v3.5.7, which contains ePxP DMAENGINE driver and
a client driver named pxp_device. This patch also includes the changes:
- use uapi header file
- remove VM_RESERVED since it's deprecated, and drop redundant VM_IO flag
since it's automatically set in remap_pfn_range()
- use <linux/platform_data/dma-imx.h> instead of <mach/dma.h>
- use devm_kzalloc() instead in pxp_probe()
- use macro __KERNEL__ in pxp_dma uapi header to avoid definition conflict
Sandor Yu [Tue, 13 Aug 2013 08:55:20 +0000 (16:55 +0800)]
ENGR00274059-02 ARM: Add new dts for imx6q/imx6dl SabreSD hdcp
hdcp ddc pins conflict with i2c2,
add new dts file for imx6q and imx6dl SabreSD board,
enable hdcp and disable i2c2 in these dts files.
Remove hdmi pins property from mx6qdl-sabresd.dtsi.
Anson Huang [Thu, 8 Aug 2013 21:05:38 +0000 (17:05 -0400)]
ENGR00274473-1 regulator: add more notifier events
Some hardware modules need strict flows according
to regulator's enable/disable, such as for i.MX6
SOC's PU regulator, there is another power gate
in GPC module, it needs to disable PU modules' clock
before PU regulator is disabled and need to enable
clock right after PU regulator is enabled, then it
can do GPC's power gate operation.
So we need to add REGULATOR_EVENT_PRE_DISABLE and
REGULATOR_EVENT_ENABLE for regulator's notifier events.
Hongzhang Yang [Mon, 12 Aug 2013 07:38:07 +0000 (15:38 +0800)]
ENGR00274761-3 Upgrade VPU driver for Linux 3.10 kernel
Modify mxc_vpu.c to adapt to kernel 3.10 change
- Remove all references to header files in mach folder
- Include linux/clk.h instead of mach/clock.h
- Call device_reset instead of imx_src_reset_vpu
- Dummy PU and PM api callings before they are ready
- Dummy cpu_is_mx5? api callings
- Remove VM_RESERVED flags
- Call gen_pool instead of iram_alloc
Modify mxc_vpu.h
- Change CONFIG_ARCH_MX6 to CONFIG_SOC_IMX6Q
Modify Kconfig:
- Change ARCH_MX? to SOC_IMX?, remove ARCH_MX3/ARCH_MX37
because for MX3 series only SOC_IMX31 and SOC_IMX35 are
defined in Linux 3.10, and these chips don't have VPU.
Need to add SOC_IMX37 to VPU Kconfig if MX37 could be
supported later.
Add VPU to config and build path
- mxc/Kconfig
- mxc/Makefile
Signed-off-by: Hongzhang Yang <Hongzhang.Yang@freescale.com>
Hongzhang Yang [Mon, 12 Aug 2013 07:23:41 +0000 (15:23 +0800)]
ENGR00274761-2 Upgrade VPU driver for Linux 3.10 kernel
Add VPU node in dtsi
- Add VPU node (common part) in imx6qdl.dtsi. It was defined
in imx6.dtsi in Linux 3.5.7.
- Add "iram" property for gen_pool api callings
- Add "resets" property for device_reset api calling
- Add VPU node (soc specific part) in imx6q.dtsi and imx6dl.dtsi
Signed-off-by: Hongzhang Yang <Hongzhang.Yang@freescale.com>
Hongzhang Yang [Mon, 12 Aug 2013 07:14:23 +0000 (15:14 +0800)]
ENGR00274761-1 Upgrade VPU driver for Linux 3.10 kernel
Pick files from origin/imx_3.5.7 commit 135bf02a0727ea5ce96
- mxc_vpu.h is picked from arch/arm/plat-mxc/include/mach/
and put to include/linux/
- drivers/mxc/vpu/Kconfig
- drivers/mxc/vpu/Makefile
- drivers/mxc/vpu/mxc_vpu.c
Signed-off-by: Hongzhang Yang <Hongzhang.Yang@freescale.com>
Sandor Yu [Mon, 12 Aug 2013 10:51:52 +0000 (18:51 +0800)]
ENGR00274821 ARM: Add i.MX6 FB properties to dts for SabreAuto board
- Add Framebuffer and ldb properties to dts for i.MX6Q and
i.MX6DL SabreAuto board.
- Add PWM3 and backlight properties to dts for i.MX6Q and
i.Mx6DL SabreAuto board.
- fix i2c2 indent in dts.
Luwei [Thu, 8 Aug 2013 08:35:24 +0000 (16:35 +0800)]
ENGR00274247: touch: add egalax touch driver support on i.MX6Q/DL AUTO/SD
Copy the egalax touch screen driver from linux3.5.7.Make some
modification.Remove the __devinit __devexit __devexit_p out
of the file, because 3.10 does not support.
This patch removes the unnecessary gpio_set_value() and
gpio_free() function calls after request the gpios with
gpio_requestion_one() successfully. Also, this patch adds
a warning message if the request fails.
Hannstar LVDS panel CABC function turns backlight density
automatically according to display content. This may introduce
annoying unstable backlight when display content changes.
So, this patch disables the CABC function if a platform's of
device tree provides controlling gpios in lvds_cabc_ctrl node.
This patch adds lvds_cabc_ctrl node in imx6qdl-sabresd.dtsi file.
This node contains two gpio entries for the Hannstar LVDS panel
CABC control function on LVDS0 and LVDS1 interfaces.
This patch adds pinmux entries for LVDS0 and LVDS1 to control the
Hannstar LVDS panel CABC function. Pin NANDF_CS2 and pin NANDF_CS3
are configured to be gpio so that they can control the CABC function.
Anson Huang [Thu, 8 Aug 2013 17:57:23 +0000 (13:57 -0400)]
ENGR00274056-3 thermal: imx: binding device cooling to thermal
1. imx thermal depends on device cooling config, as only cpu
cooling is not enough for cooling down SOC;
2. binding device cooling to imx thermal driver.
3. add temperature buffer for passive trip, which means when
temperature cross passive trip, cooling devices will be triggered,
but only when temperature drop to more than the number we defined(10 C)
lower than passive trip, cooling devices will be canceled. this
is to avoid triggering/canceling cooling device back and forth when
temperature is around passive trip.
Anson Huang [Thu, 8 Aug 2013 17:20:40 +0000 (13:20 -0400)]
ENGR00274056-1 thermal: add device cooling for thermal driver
cpu cooling is not enough when temperature is
too hot, as some devices may contribute a lot of heat
to SOC, such as GPU, so we need to add device cooling
as well, when system is too hot, devices can also take
their actions to lower SOC temperature.
when temperature cross the passive trip, device cooling
driver will send out notification, those devices who
register this devfreq_cooling notification will take
actions to lower SOC temperature.
Robin Gong [Mon, 5 Aug 2013 09:40:02 +0000 (17:40 +0800)]
ENGR00273425 ARM: imx: enable suspend code for imx6q/dl
Enable DSM code for imx6, the code porting form kernel 3.5.7.So with the patch,
we can suspend imx6q, imx6dl from iram to decrease power number of DDR IO:
save ~15mA@1.5V on imx6qsabresd, but need more ~30us in suspend and resume back.
Liu Ying [Mon, 5 Aug 2013 07:47:22 +0000 (15:47 +0800)]
ENGR00273974-1 media: port mxc vout driver from 3.5.7 to 3.10
This is porting mxc vout driver from imx_3.5.7 kernel to
imx_3.10 kernel.
* Put the driver in drivers/media/platform/ directory instead
of drivers/media/video/ directory, since the later one is
renamed to the former one in 3.10 kernel.
* Change the ipu-v3.h header file from <mach/ipu-v3.h> to
<linux/ipu-v3.h>.
* Change the mxc_vidioc_s_crop() function's implementation since
the definition of the vidioc_s_crop() function is modified to
make the last argument be constant.
* Set vfl_dir to be VFL_DIR_TX since the ioctrl validity checks
are improved in 3.10 kernel.
* Remove 'defaut y' setting for VIDEO_MXC_OUTPUT and
VIDEO_MXC_IPU_OUTPUT Kconfigs. They may be configured by kernel
default configure or by user.
* Make VIDEO_MXC_OUTPUT Kconfig depend on FB_MXC Kconfig since
we need framebuffers to be rendered.
* Make VIDEO_MXC_IPU_OUTPUT Kconfig be tristate.
* Split <linux/mxc_v4l2.h> header file up into include/linux/
and include/uapi/linux/ directories so that the userspace may
include the mxc_v4l2.h header file.
Liu Ying [Mon, 5 Aug 2013 07:33:49 +0000 (15:33 +0800)]
ENGR00273852 ipu: header file split up
This patch splits ipu header file up to
include/linux/ directory and include/uapi/linux/
directory so that the userspace may include
the ipu header file. This patch also fixes some
annotations and macros about the header file's
naming.
Liu Ying [Thu, 1 Aug 2013 08:32:11 +0000 (16:32 +0800)]
ENGR00273500 IPUv3 dev: use wait_event_interruptible for ipu task
The ipu task thread checks outstanding tasks to be done on waiting
event uninterruptibly on the function find_task()'s return value.
However, sleeping on waiting event uninterruptibly contributes to
system load average value. This patch changes wait_event() to
wait_event_interruptible() to avoid the load average value inflation.
Fabio Estevam [Sun, 9 Jun 2013 18:17:18 +0000 (15:17 -0300)]
serial: imx: Fix serial clock unbalance
Since commit 0c375501 (serial: imx: enable the clocks for console), the
imx_startup() function calls clk_prepare_enable conditionally, so we
need to call clk_disable_unprepare inside imx_shutdown() under the same
condition to avoid unbalanced clock calls.
ENGR00240988: ARM: imx6q: add dma_zone_size for GPU limit
GPU has a limit on physical address that it accesses, which must be
below 2GiB. Since i.MX6Q/DL maps system memory at 0x10000000 (offset
256MiB), we set dma_zone_size as (SZ_2G - SZ_256M) to ensure that.
ENGR00240988: gpu: fix deprecated idr calls on 3.10 kernel
The idr calls idr_pre_get() and idr_get_new_above() are deprecated on
3.10 kernel and cause the following build issues. Replace the calls
with the new idr_alloc() to fix the issue.
CC drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_os.o
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_os.c: In function ‘_AllocateIntegerId’:
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_os.c:776:5: error: ‘idr_pre_get’ is deprecated (declared at include/linux/idr.h:151) [-Werror=deprecated-declarations]
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_os.c:784:5: error: ‘idr_get_new_above’ is deprecated (declared at include/linux/idr.h:166) [-Werror=deprecated-declarations]
ENGR00240988: gpu: allocate contiguous memory from CMA for 3.10 kernel
The Contiguous Memory Allocator (CMA) is mature in 3.10 kernel. Let's
change gpu driver to allocate contiguous memory from CMA pool. Doing so
will save not only the memblock reserve calls in machine code but also
the request_mem_region() and ioremap() in gpu driver. And all the
system memory will be seen by kernel no matter whether gpu driver is
running or not.
It also changes the default contiguousSize to 128 MiB for Freescale
adjustment.
ENGR00240988: gpu: __devinit and __devexit are unavailable on 3.10 kernel
__devinit, __devexit and __devexit_p are unavailable on 3.10 kernel.
Remove them for 3.10 to fix the compile issues below.
CC drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_driver.o
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_driver.c:1033:22: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘gpu_probe’
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_driver.c:1116:22: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘gpu_remove’
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_driver.c:1292:19: error: ‘gpu_probe’ undeclared here (not in a function)
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_driver.c:1293:5: error: implicit declaration of function ‘__devexit_p’ [-Werror=implicit-function-declaration]
ENGR00240988: gpu: comment out busfreq calls for 3.10 kernel
The busfreq driver is not ready yet on 3.10 kernel. Let's comment out
the busfreq header inclusion and function calls for now, and revisit it
later when busfreq driver is ready.
ENGR00240988: gpu: mach/hardware.h is not available in kernel 3.10
In kernel 3.10, drivers can not include any <mach/*> headers. Do not
include <mach/hardware.h> for 3.10 kernel to fix the follow build
errors.
CC drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_device.o
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_device.c:28:27: fatal error: mach/hardware.h: No such file or directory
CC drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_os.o
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_os.c:33:27: fatal error: mach/hardware.h: No such file or directory
ENGR00273073-2 cpufreq: add interactive governor for cpufreq
cpufreq: interactive: New 'interactive' governor
This governor is designed for latency-sensitive workloads, such as
interactive user interfaces. The interactive governor aims to be
significantly more responsive to ramp CPU quickly up when CPU-intensive
activity begins.
Existing governors sample CPU load at a particular rate, typically
every X ms. This can lead to under-powering UI threads for the period of
time during which the user begins interacting with a previously-idle system
until the next sample period happens.
The 'interactive' governor uses a different approach. Instead of sampling
the CPU at a specified rate, the governor will check whether to scale the
CPU frequency up soon after coming out of idle. When the CPU comes out of
idle, a timer is configured to fire within 1-2 ticks. If the CPU is very
busy from exiting idle to when the timer fires then we assume the CPU is
underpowered and ramp to MAX speed.
If the CPU was not sufficiently busy to immediately ramp to MAX speed, then
the governor evaluates the CPU load since the last speed adjustment,
choosing the highest value between that longer-term load or the short-term
load since idle exit to determine the CPU speed to ramp to.
A realtime thread is used for scaling up, giving the remaining tasks the
CPU performance benefit, unlike existing governors which are more likely to
schedule rampup work to occur after your performance starved tasks have
completed.
The tuneables for this governor are:
/sys/devices/system/cpu/cpufreq/interactive/min_sample_time:
The minimum amount of time to spend at the current frequency before
ramping down. This is to ensure that the governor has seen enough
historic CPU load data to determine the appropriate workload.
/sys/devices/system/cpu/cpufreq/interactive/go_maxspeed_load
The CPU load at which to ramp to max speed.
Signed-off-by: Mike Chan <mike at android.com> Signed-off-by: Todd Poynor <toddpoynor at google.com> Signed-off-by: Allen Martin <amartin at nvidia.com> (submitted improvements) Signed-off-by: Axel Haslam <axelhaslam at ti.com> (submitted improvements) Signed-off-by: Anton Vorontsov <anton.vorontsov at linaro.org> Signed-off-by: Anson Huang <b20788@freescale.com>
ENGR00240987: ipu: port ipuv3 driver from 3.5.7 kernel
This is a fast-forward porting of ipuv3 driver from 3.5.7 kernel to
kernel 3.10. The change set is kept as minimum as possible with only
making necessary code changes to adapt 3.10 kernel internal API and
framework updates. Everything else should be same as 3.5.7 one. The
change set consists of the following.
* Remove unused Kconfig options MXC_IPU_V3D, MXC_IPU_V3EX and
MXC_IPU_V3H
* Comment out busfreq calls
* Move ipu-v3.h into include/linux/, and remove all <mach/*> includes
* Drop __devinit and __devexit
* Remove assignment of pltfm_data->pg = imx6q_ipu_pg;
* Use generic device_reset() API rather than ipu_pltfm_data->init()
hook to reset IPU
* Includes <linux/sched/rt.h> ipu_device.c to fix undeclared
MAX_USER_RT_PRIO error
* Change compatible string to "fsl,imx6q-ipu" to align with community
kernel
* Define irq_sync before irq_err in DTS to align with community kernel
* Drop "ipu1_" and "ipu2_" from clock names to save the handling of the
second parameter of devm_clk_get()
* Remove the buggy csi_clk setup in ipu_clk_setup_enable() and validate
the clock before operate on it in ipu_csi_enable_mclk()
* Replace iram API (linux/iram_alloc.h) with generic memory pool API
(linux/genalloc.h) in VDOA driver
ARM: dts: imx: ocram size is different between imx6q and imx6dl
The ocram on imx6q is 256 KiB while on imx6dl it's 128 KiB. Let's
have separate node for imx6q and imx6dl. It also changes imx6q size
0x3f000 to 0x40000 to match the hardware.
ENGR00269945: pinctrl: support pinctrl setting assertion via gpios
It's pretty common that on some reference design or validation boards,
one pin could be used by two devices on board, and the pin route is
controlled by a GPIO. So to assert the pin for given device, not only
the pinmux controller in SoC needs to be set up properly but also the
GPIO needs to be pulled up/down.
The patch adds support of a device tree property "pinctrl-assert-gpios"
under client device node. It plays pretty much like a board level pin
multiplexer, and steers the pin route by controlling the GPIOs. When
client device has the property represent in its node, pinctrl device
tree mapping function will firstly pull up/down the GPIOs to assert the
pins for the device at board level.
Linus Torvalds [Sun, 3 Aug 2014 16:58:20 +0000 (09:58 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two fixes in the timer area:
- a long-standing lock inversion due to a printk
- suspend-related hrtimer corruption in sched_clock"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timer: Fix lock inversion between hrtimer_bases.lock and scheduler locks
sched_clock: Avoid corrupting hrtimer tree during suspend
Linus Torvalds [Sat, 2 Aug 2014 17:57:39 +0000 (10:57 -0700)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"A few fixes for ARM. Some of these are correctness issues:
- TLBs must be flushed after the old mappings are removed by the DMA
mapping code, but before the new mappings are established.
- An off-by-one entry error in the Keystone LPAE setup code.
Fixes include:
- ensuring that the identity mapping for LPAE does not remove the
kernel image from the identity map.
- preventing userspace from trapping into kgdb.
- fixing a preemption issue in the Intel iwmmxt code.
- fixing a build error with nommu.
Other changes include:
- Adding a note about which areas of memory are expected to be
accessible while the identity mapping tables are in place"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8124/1: don't enter kgdb when userspace executes a kgdb break instruction
ARM: idmap: add identity mapping usage note
ARM: 8115/1: LPAE: reduce damage caused by idmap to virtual memory layout
ARM: fix alignment of keystone page table fixup
ARM: 8112/1: only select ARM_PATCH_PHYS_VIRT if MMU is enabled
ARM: 8100/1: Fix preemption disable in iwmmxt_task_enable()
ARM: DMA: ensure that old section mappings are flushed from the TLB
Omar Sandoval [Fri, 1 Aug 2014 17:14:06 +0000 (18:14 +0100)]
ARM: 8124/1: don't enter kgdb when userspace executes a kgdb break instruction
The kgdb breakpoint hooks (kgdb_brk_fn and kgdb_compiled_brk_fn)
should only be entered when a kgdb break instruction is executed
from the kernel. Otherwise, if kgdb is enabled, a userspace program
can cause the kernel to drop into the debugger by executing either
KGDB_BREAKINST or KGDB_COMPILED_BREAK.
Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Omar Sandoval <osandov@osandov.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 29 Jul 2014 11:18:34 +0000 (12:18 +0100)]
ARM: idmap: add identity mapping usage note
Add a note about the usage of the identity mapping; we do not support
accesses outside of the identity map region and kernel image while a
CPU is using the identity map. This is because the identity mapping
may overwrite vmalloc space, IO mappings, the vectors pages, etc.
Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Sat, 2 Aug 2014 00:37:01 +0000 (17:37 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Peter Anvin:
"A single fix to not invoke the espfix code on Xen PV, as it turns out
to oops the guest when invoked after all. This patch leaves some
amount of dead code, in particular unnecessary initialization of the
espfix stacks when they won't be used, but in the interest of keeping
the patch minimal that cleanup can wait for the next cycle"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86_64/entry/xen: Do not invoke espfix64 on Xen
Linus Torvalds [Sat, 2 Aug 2014 00:16:05 +0000 (17:16 -0700)]
Merge tag 'staging-3.16-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver bugfixes from Greg KH:
"Here are some tiny staging driver bugfixes that I've had in my tree
for the past week that resolve some reported issues. Nothing major at
all, but it would be good to get them merged for 3.16-rc8 or -final"
* tag 'staging-3.16-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vt6655: Fix disassociated messages every 10 seconds
staging: vt6655: Fix Warning on boot handle_irq_event_percpu.
staging: rtl8723au: rtw_resume(): release semaphore before exit on error
iio:bma180: Missing check for frequency fractional part
iio:bma180: Fix scale factors to report correct acceleration units
iio: buffer: Fix demux table creation
Linus Torvalds [Fri, 1 Aug 2014 19:49:02 +0000 (12:49 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM straggler SoC fix from Olof Johansson:
"A DT bugfix for Nomadik that had an ambigouos double-inversion of a
gpio line, and one MAINTAINER URL update that might as well go in now.
We could hold off until the merge window, but then we'll just have to
mark the DT fix for stable and it just seems like in total causing
more work"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Update Tegra Git URL
ARM: nomadik: fix up double inversion in DT
Anssi Hannula [Fri, 1 Aug 2014 15:55:47 +0000 (11:55 -0400)]
dm cache: fix race affecting dirty block count
nr_dirty is updated without locking, causing it to drift so that it is
non-zero (either a small positive integer, or a very large one when an
underflow occurs) even when there are no actual dirty blocks. This was
due to a race between the workqueue and map function accessing nr_dirty
in parallel without proper protection.
People were seeing under runs due to a race on increment/decrement of
nr_dirty, see: https://lkml.org/lkml/2014/6/3/648
Fix this by using an atomic_t for nr_dirty.
Reported-by: roma1390@gmail.com Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi> Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org
1d3d4437eae1 ("vmscan: per-node deferred work") added a flags field to
struct shrinker assuming that all shrinkers were zero filled. The dm
bufio shrinker is not zero filled, which leaves arbitrary kmalloc() data
in flags. So far the only defined flags bit is SHRINKER_NUMA_AWARE.
But there are proposed patches which add other bits to shrinker.flags
(e.g. memcg awareness).
Rather than simply initializing the shrinker, this patch uses kzalloc()
when allocating the dm_bufio_client to ensure that the embedded shrinker
and any other similar structures are zeroed.
This fixes theoretical over aggressive shrinking of dm bufio objects.
If the uninitialized dm_bufio_client.shrinker.flags contains
SHRINKER_NUMA_AWARE then shrink_slab() would call the dm shrinker for
each numa node rather than just once. This has been broken since 3.12.
Jan Kara [Fri, 1 Aug 2014 10:20:02 +0000 (12:20 +0200)]
timer: Fix lock inversion between hrtimer_bases.lock and scheduler locks
clockevents_increase_min_delta() calls printk() from under
hrtimer_bases.lock. That causes lock inversion on scheduler locks because
printk() can call into the scheduler. Lockdep puts it as:
======================================================
[ INFO: possible circular locking dependency detected ] 3.15.0-rc8-06195-g939f04b #2 Not tainted
-------------------------------------------------------
trinity-main/74 is trying to acquire lock:
(&port_lock_key){-.....}, at: [<811c60be>] serial8250_console_write+0x8c/0x10c
but task is already holding lock:
(hrtimer_bases.lock){-.-...}, at: [<8103caeb>] hrtimer_try_to_cancel+0x13/0x66
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Fix the problem by using printk_deferred() which does not call into the
scheduler.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Jan Kara <jack@suse.cz> Cc: stable@vger.kernel.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Eric Biggers [Wed, 25 Jun 2014 04:45:08 +0000 (23:45 -0500)]
vfs: fix check for fallocate on active swapfile
Fix the broken check for calling sys_fallocate() on an active swapfile,
introduced by commit 0790b31b69374ddadefe ("fs: disallow all fallocate
operation on active swapfile").
Signed-off-by: Eric Biggers <ebiggers3@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The direct-io.c rewrite to use the iov_iter infrastructure stopped updating
the size field in struct dio_submit, and thus rendered the check for
allowing asynchronous completions to always return false. Fix this by
comparing it to the count of bytes in the iov_iter instead.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Tim Chen <tim.c.chen@linux.intel.com> Tested-by: Tim Chen <tim.c.chen@linux.intel.com>
Merge tag 'pm+acpi-3.16-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"One commit that fixes a problem causing PNP devices to be associated
with wrong ACPI device objects sometimes during device enumeration due
to an incorrect check in a matching function.
That problem was uncovered by the ACPI device enumeration rework in
3.14"
* tag 'pm+acpi-3.16-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PNP: Fix acpi_pnp_match()
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux
Pull clock driver fix from Mike Turquette:
"A single patch to re-enable audio which is broken on all DRA7
SoC-based platforms. Missed this one from the last set of fixes"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: ti: clk-7xx: Correct ABE DPLL configuration
Pull crypto fix from Herbert Xu:
"This adds missing SELinux labeling to AF_ALG sockets which apparently
causes SELinux (or at least the SELinux people) to misbehave :)"
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI barrier fix from James Bottomley:
"This is a potential data corruption fix: If we get an error sending
down a barrier, we simply ignore it meaning the barrier semantics get
violated without anyone being any the wiser. If the system crashes at
this point, the filesystem potentially becomes corrupt. Fix is to
report errors on failed barriers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: handle flush errors properly
Peter Ujfalusi [Wed, 2 Apr 2014 13:48:45 +0000 (16:48 +0300)]
clk: ti: clk-7xx: Correct ABE DPLL configuration
ABE DPLL frequency need to be lowered from 361267200
to 180633600 to facilitate the ATL requironments.
The dpll_abe_m2x2_ck clock need to be set to double
of ABE DPLL rate in order to have correct clocks
for audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Mike Turquette <mturquette@linaro.org>
Milan Broz [Tue, 29 Jul 2014 18:41:09 +0000 (18:41 +0000)]
crypto: af_alg - properly label AF_ALG socket
Th AF_ALG socket was missing a security label (e.g. SELinux)
which means that socket was in "unlabeled" state.
This was recently demonstrated in the cryptsetup package
(cryptsetup v1.6.5 and later.)
See https://bugzilla.redhat.com/show_bug.cgi?id=1115120
This patch clones the sock's label from the parent sock
and resolves the issue (similar to AF_BLUETOOTH protocol family).
Cc: stable@vger.kernel.org Signed-off-by: Milan Broz <gmazyland@gmail.com> Acked-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
David Rientjes [Thu, 31 Jul 2014 02:05:55 +0000 (19:05 -0700)]
kexec: fix build error when hugetlbfs is disabled
free_huge_page() is undefined without CONFIG_HUGETLBFS and there's no
need to filter PageHuge() page is such a configuration either, so avoid
exporting the symbol to fix a build error:
In file included from kernel/kexec.c:14:0:
kernel/kexec.c: In function 'crash_save_vmcoreinfo_init':
kernel/kexec.c:1623:20: error: 'free_huge_page' undeclared (first use in this function)
VMCOREINFO_SYMBOL(free_huge_page);
^
Introduced by commit 8f1d26d0e59b ("kexec: export free_huge_page to
VMCOREINFO")
Reported-by: kbuild test robot <fengguang.wu@intel.com> Acked-by: Olof Johansson <olof@lixom.net> Cc: Atsushi Kumagai <kumagai-atsushi@mxc.nes.nec.co.jp> Cc: Baoquan He <bhe@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Rientjes <rientjes@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
Josh has moved
kexec: export free_huge_page to VMCOREINFO
mm: fix filemap.c pagecache_get_page() kernel-doc warnings
mm: debugfs: move rounddown_pow_of_two() out from do_fault path
memcg: oom_notify use-after-free fix
hwpoison: call action_result() in failure path of hwpoison_user_mappings()
hwpoison: fix hugetlbfs/thp precheck in hwpoison_user_mappings()
rapidio/tsi721_dma: fix failure to obtain transaction descriptor
mm, thp: do not allow thp faults to avoid cpuset restrictions
mm/page-writeback.c: fix divide by zero in bdi_dirty_limits()
PG_head_mask was added into VMCOREINFO to filter huge pages in b3acc56bfe1
("kexec: save PG_head_mask in VMCOREINFO"), but makedumpfile still need
another symbol to filter *hugetlbfs* pages.
If a user hope to filter user pages, makedumpfile tries to exclude them by
checking the condition whether the page is anonymous, but hugetlbfs pages
aren't anonymous while they also be user pages.
We know it's possible to detect them in the same way as PageHuge(),
so we need the start address of free_huge_page():
int PageHuge(struct page *page)
{
if (!PageCompound(page))
return 0;
Fix kernel-doc warnings in mm/filemap.c: pagecache_get_page():
Warning(..//mm/filemap.c:1054): No description found for parameter 'cache_gfp_mask'
Warning(..//mm/filemap.c:1054): No description found for parameter 'radix_gfp_mask'
Warning(..//mm/filemap.c:1054): Excess function parameter 'gfp_mask' description in 'pagecache_get_page'
Fixes: 2457aec63745 ("mm: non-atomically mark page accessed during page cache allocation where possible")
[mgorman@suse.de: change everything]
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Mel Gorman <mgorman@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: debugfs: move rounddown_pow_of_two() out from do_fault path
do_fault_around() expects fault_around_bytes rounded down to nearest page
order. Instead of calling rounddown_pow_of_two every time in
fault_around_pages()/fault_around_mask() we could do round down when user
changes fault_around_bytes via debugfs interface.
This also fixes bug when user set fault_around_bytes to 0. Result of
rounddown_pow_of_two(0) is not defined, therefore fault_around_bytes == 0
doesn't work without this patch.
Let's set fault_around_bytes to PAGE_SIZE if user sets to something less
than PAGE_SIZE
[akpm@linux-foundation.org: tweak code layout] Fixes: a9b0f861("mm: nominate faultaround area in bytes rather than page order") Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Reported-by: Sasha Levin <sasha.levin@oracle.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: <stable@vger.kernel.org> [3.15.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit fb2a6fc56be6 ("mm: memcg: rework and document OOM waiting and
wakeup") has moved mem_cgroup_oom_notify outside of memcg_oom_lock
assuming it is protected by the hierarchical OOM-lock.
Although this is true for the notification part the protection doesn't
cover unregistration of event which can happen in parallel now so
mem_cgroup_oom_notify can see already unlinked and/or freed
mem_cgroup_eventfd_list.
Fix this by using memcg_oom_lock also in mem_cgroup_oom_notify.
hwpoison: call action_result() in failure path of hwpoison_user_mappings()
hwpoison_user_mappings() could fail for various reasons, so printk()s to
print out the reasons should be done in each failure check inside
hwpoison_user_mappings().
And currently we don't call action_result() when hwpoison_user_mappings()
fails, which is not consistent with other exit points of memory error
handler. So this patch fixes these messaging problems.