Jiri Pirko [Thu, 24 Jan 2013 09:41:41 +0000 (09:41 +0000)]
ipv4: introduce address lifetime
There are some usecase when lifetime of ipv4 addresses might be helpful.
For example:
1) initramfs networkmanager uses a DHCP daemon to learn network
configuration parameters
2) initramfs networkmanager addresses, routes and DNS configuration
3) initramfs networkmanager is requested to stop
4) initramfs networkmanager stops all daemons including dhclient
5) there are addresses and routes configured but no daemon running. If
the system doesn't start networkmanager for some reason, addresses and
routes will be used forever, which violates RFC 2131.
This patch is essentially a backport of ivp6 address lifetime mechanism
for ipv4 addresses.
Current "ip" tool supports this without any patch (since it does not
distinguish between ipv4 and ipv6 addresses in this perspective.
Also, this should be back-compatible with all current netlink users.
Reported-by: Pavel Šimerda <psimerda@redhat.com> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 29 Jan 2013 18:37:29 +0000 (13:37 -0500)]
Merge branch 'ipfrags'
Jesper Dangaard Brouer says:
====================
This patchset is V2, with some trivial code fixes, which were noticed
by DaveM. It is still a partly respin of my fragmentation optimization
patches: http://thread.gmane.org/gmane.linux.network/250914
This is not the complete patchset, from the gmane link above. In this
patchset, I primarily focus on adjusting cacheline for better SMP/NUMA
performance.
Once this patchset have been agreed upon, I will continue and respin
the rest of my patches.
This time around, I have created a frag DoS generator, via the tool
trafgen (http://netsniff-ng.org/). To create a stable DoS scenario
(no longer relying on frame dropping due to disabled flow-control).
Two 10G interfaces are under-test, and uses Ethernet flow-control. A
third interface is used for generating the DoS attack (this interface
is also 10G, but it does not need to be, as 500Kpps DoS is enough).
Test types summary (netperf):
Test-20G64K == 2x10G with 65K fragments
Test-20G3F == 2x10G with 3x fragments (3*1472 bytes)
Test-20G64K+DoS == Same as 20G64K with frag DoS
Test-20G3F+DoS == Same as 20G3F with frag DoS
Patch list:
Patch-01 - net: cacheline adjust struct netns_frags for better frag performance
Patch-02 - net: cacheline adjust struct inet_frags for better frag performance
Patch-03 - net: cacheline adjust struct inet_frag_queue
Patch-04 - net: frag helper functions for mem limit tracking
Patch-05 - net: use lib/percpu_counter API for fragmentation mem accounting
Patch-06 - net: frag, move LRU list maintenance outside of rwlock
I cannot explain the under-DoS regression that patch-05/percpu_counter
introduces. But patch-06/LRU-lock corrects the situation again.
Below is a testlab setup description, with links to the trafgen DoS
packet config used.
Testlab
=======
Server setup
------------
The machine acting as a server:
- 2x CPU (E5-2630)
- Thus a NUMA arch/machine
- 4x 10Gbit/s ports
- NICs 2x Intel Dual port 82599 based (driver ixgbe)
Setup:
- Interfaces uses Ethernet flow control
- Flush all iptables
- Remove all iptables related module.
- Kill irqbalance
- Pin each 10G NIC port to a *single* CPU each
Pinning can easily be done by command hacks::
for x in /proc/irq/*/eth8*/../smp_affinity_list ; do echo 1 > $x; done
for x in /proc/irq/*/eth9*/../smp_affinity_list ; do echo 3 > $x; done
for x in /proc/irq/*/eth31*/../smp_affinity_list; do echo 6 > $x; done
for x in /proc/irq/*/eth32*/../smp_affinity_list; do echo 8 > $x; done
Notice NUMA setting: The CPU to NIC tying is carefully choosen
according to the NUMA node setup. Thus, NICs connected to a PCI-e
slot that is connected to a physical CPU socket are tied together.
Choosing only a single CPU per NIC (port) is just to ease provoking
and debugging this performance issue. (In real setups, you can choose
more CPU, just remember the NUMA node in the equation).
Tools
-----
Netperf is used, with option -T to ensure CPU binding.
The netserver processes, are NAPI pinned::
net: frag, move LRU list maintenance outside of rwlock
Updating the fragmentation queues LRU (Least-Recently-Used) list,
required taking the hash writer lock. However, the LRU list isn't
tied to the hash at all, so we can use a separate lock for it.
Original-idea-by: Florian Westphal <fw@strlen.de> Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: use lib/percpu_counter API for fragmentation mem accounting
Replace the per network namespace shared atomic "mem" accounting
variable, in the fragmentation code, with a lib/percpu_counter.
Getting percpu_counter to scale to the fragmentation code usage
requires some tweaks.
At first view, percpu_counter looks superfast, but it does not
scale on multi-CPU/NUMA machines, because the default batch size
is too small, for frag code usage. Thus, I have adjusted the
batch size by using __percpu_counter_add() directly, instead of
percpu_counter_sub() and percpu_counter_add().
The batch size is increased to 130.000, based on the largest 64K
fragment memory usage. This does introduce some imprecise
memory accounting, but its does not need to be strict for this
use-case.
It is also essential, that the percpu_counter, does not
share cacheline with other writers, to make this scale.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This change is primarily a preparation to ease the extension of memory
limit tracking.
The change does reduce the number atomic operation, during freeing of
a frag queue. This does introduce a some performance improvement, as
these atomic operations are at the core of the performance problems
seen on NUMA systems.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fragmentation code cacheline adjusting of struct inet_frag_queue.
Take advantage of the size of struct timer_list, and move all but
spinlock_t lock, below the timer struct. On 64-bit 'lru_list',
'list' and 'refcnt', fits exactly into the next cacheline, and a
new cacheline starts at 'fragments'.
The netns_frags *net pointer is moved to the end of the struct,
because its used in a compare, with "next/close-by" elements of
which this struct is embedded into.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: cacheline adjust struct inet_frags for better frag performance
The globally shared rwlock, of struct inet_frags, shares
cacheline with the 'rnd' number, which is used by the hash
calculations. Fix this, as this obviously is a bad idea, as
unnecessary cache-misses will occur when accessing the 'rnd'
number.
Also small note that, moving function ptr (*match) up in struct,
is to avoid it lands on the next cacheline (on 64-bit).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: cacheline adjust struct netns_frags for better frag performance
This small cacheline adjustment of struct netns_frags improves
performance significantly for the fragmentation code.
Struct members 'lru_list' and 'mem' are both hot elements, and it
hurts performance, due to cacheline bouncing at every call point,
when they share a cacheline. Also notice, how mem is placed
together with 'high_thresh' and 'low_thresh', as they are used in
the compare operations together.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net neigh: Optimize neighbor entry size calculation.
When allocating memory for neighbour cache entry, if
tbl->entry_size is not set, we always calculate
sizeof(struct neighbour) + tbl->key_len, which is common
in the same table.
With this change, set tbl->entry_size during the table
initialization phase, if it was not set, and use it in
neigh_alloc() and neighbour_priv().
This change also allow us to have both of protocol private
data and device priate data at tha same time.
Note that the only user of prototcol private is DECnet
and the only user of device private is ATM CLIP.
Since those are exclusive, we have not been facing issues
here.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: avoid to hang up on sending due to sysctl configuration overflow.
I found if we write a larger than 4GB value to some sysctl
variables, the sending syscall will hang up forever, because these
variables are 32 bits, such large values make them overflow to 0 or
negative.
This patch try to fix overflow or prevent from zero value setup
of below sysctl variables:
net.core.wmem_default
net.core.rmem_default
net.core.rmem_max
net.core.wmem_max
net.ipv4.udp_rmem_min
net.ipv4.udp_wmem_min
net.ipv4.tcp_wmem
net.ipv4.tcp_rmem
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Li Yu <raise.sail@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jamie Gloudon [Wed, 23 Jan 2013 18:05:04 +0000 (18:05 +0000)]
via-rhine: add 64bit statistics.
Switch to use ndo_get_stats64 to get 64bit statistics.
Signed-off-by: Jamie Gloudon <jamie.gloudon@gmail.com> Tested-by: Jamie Gloudon <jamie.gloudon@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David J. Choi [Wed, 23 Jan 2013 14:05:15 +0000 (14:05 +0000)]
drivers/net/phy/micrel_phy: Add support for new PHYs
Summary of changes:
.Newly added phys
-KSZ8081/KSZ8091, which has some phy ids.
-KSZ8061
-KSZ9031, which is Gigabit phy.
-KSZ886X, which has a switch function.
-KSZ8031, which has a same phy ids with KSZ8021.
Signed-off-by: David J. Choi <david.choi@micrel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Sun, 27 Jan 2013 15:55:21 +0000 (15:55 +0000)]
netpoll: use the net namespace of current process instead of init_net
This will allow us to setup netconsole in a different namespace
rather than where init_net is.
Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Tue, 22 Jan 2013 21:29:39 +0000 (21:29 +0000)]
netpoll: add RCU annotation to npinfo field
dev->npinfo is protected by RCU.
This fixes the following sparse warnings:
net/core/netpoll.c:177:48: error: incompatible types in comparison expression (different address spaces)
net/core/netpoll.c:200:35: error: incompatible types in comparison expression (different address spaces)
net/core/netpoll.c:221:35: error: incompatible types in comparison expression (different address spaces)
net/core/netpoll.c:327:18: error: incompatible types in comparison expression (different address spaces)
Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Jan 2013 23:21:38 +0000 (18:21 -0500)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John W. Linville says:
====================
Included is an NFC pull. Samuel says:
"It brings the following goodies:
- LLCP socket timestamping (To be used e.g with the recently released nfctool
application for a more efficient skb timestamping when sniffing).
- A pretty big pn533 rework from Waldemar, preparing the driver to support
more flavours of pn533 based devices.
- HCI changes from Eric in preparation for the microread driver support.
- Some LLCP memory leak fixes, cleanups and slight improvements.
- pn544 and nfcwilink move to the devm_kzalloc API.
- An initial Secure Element (SE) API.
- An nfc.h license change from the original author, allowing non GPL
application code to safely include it."
Also included are a pair of mac80211 pulls. Johannes says:
"We found two bugs in the previous code, so I'm sending you a pull
request again this soon.
This contains two regulatory bug fixes, some of Thomas's hwsim beacon
timer work and a documentation fix from Bob."
"Another pull request for mac80211-next. This time, I have a number of
things, the patches are mostly self-explanatory. There are a few fixes
from Felix and myself, and random cleanups & improvements. The biggest
thing is the partial patchset from Marco preparing for mesh powersave."
Additionally, there are a pair of iwlwifi pulls. Johannes says:
"For iwlwifi-next, I have a few cleanups/improvements as well as a few
not very important fixes and more preparations for new devices."
"Please pull a few updates for iwlwifi. These are just some cleanups and
a debug improvement."
On top of that, there is a slew of driver updates. This includes
brcmfmac, mwifiex, ath9k, carl9170, and mwl8k as well as a handful
of others. The bcma and ssb busses get some attention as well.
Still, I don't see any big headliners here.
Also included is a pull of the wireless tree, in order to resolve
some merge conflicts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Jan 2013 23:18:17 +0000 (18:18 -0500)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
This series contains updates to e1000e, ixgbevf, igb and igbvf.
Majority of the patches are code cleanups of e1000e where code
is removed (Yeah!). The other two e1000e patches are fixes. The
first is to fix the maximum frame size for 82579 devices. The second
fix is to resolve an issue with devices other than 82579 that suffer
from dropped transactions on platforms with deep C-states when
jumbo frames are enabled.
The ixgbevf patch is to ensure that the driver fetches the correct,
refreshed value for link status and speed when the values have changed.
The igb and igbvf patches are a solution to an issue Stefan Assmann
reported, where when the PF is up and igbvf is loaded, the MAC address
is not generated using eth_hw_addr_random().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Mon, 28 Jan 2013 08:33:33 +0000 (08:33 +0000)]
can: rework skb reserved data handling
Added accessor and skb_reserve helpers for struct can_skb_priv.
Removed pointless skb_headroom() check.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> CC: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Mitch A Williams [Fri, 18 Jan 2013 08:57:20 +0000 (08:57 +0000)]
igbvf: be sane about random MAC addresses
Tighten up some of the code surrounding MAC addresses. Since the PF is
now giving all zeros instead of a random address, check for this case
and generate a random address. This ensures that we always know when we
have a random address and udev won't get upset about it.
Additionally, tighten up some of the log messages and clean up the
formatting.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: Stefan Assmann <sassmann@kpanic.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Tested-by: Stefan Assmann <sassmann@redhat.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch A Williams [Fri, 18 Jan 2013 08:57:20 +0000 (08:57 +0000)]
igb: Don't give VFs random MAC addresses
If the user has not assigned a MAC address to a VM, then don't give it a
random one. Instead, just give it zeros and let it figure out what to do
with them.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: Stefan Assmann <sassmann@kpanic.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Tested-by: Stefan Assmann <sassmann@redhat.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Greg Rose [Thu, 24 Jan 2013 04:54:48 +0000 (04:54 +0000)]
ixgbevf: Make sure link status and speed are fetched
A recent change makes it necessary to set get_link_status to ensure that
the driver fetches the correct, refreshed value for link status and speed
when it has changed in the physical function device.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Sat, 12 Jan 2013 07:26:53 +0000 (07:26 +0000)]
e1000e: cleanup: remove comments which are no longer applicable
Code was removed but the applicable comments were not.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Sat, 12 Jan 2013 07:26:22 +0000 (07:26 +0000)]
e1000e: cleanup hw.h
Remove unnecessary #include, forward prototype of struct e1000_adapter and
an empty comment; fix a comment which mentions "static data for the MAC"
which is not applicable to the following struct; and cleanup some
whitespace issues.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Sat, 12 Jan 2013 07:25:52 +0000 (07:25 +0000)]
e1000e: cleanup: remove unused #define
All references to E1000_ERT_2048 have been removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Sat, 12 Jan 2013 07:25:22 +0000 (07:25 +0000)]
e1000e: adjust PM QoS request
It has been found that devices other than 82579 (a.k.a. e1000_pch2lan)
suffer from dropped transactions on platforms with deep C-states when
jumbo frames are enabled. For example, LOMs on ICH9- and ICH10-based
platforms which recently had early-receive de-featured (for stability
reasons) suffer from this. To resolve this for all devices, when jumbo
frames are enabled set the PM QoS DMA latency request based on the size
of the receive packet buffer less one full frame.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Wed, 9 Jan 2013 01:20:46 +0000 (01:20 +0000)]
e1000e: correct maximum frame size on 82579
The largest jumbo frame supported by the 82579 hardware is 9018.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Wed, 23 Jan 2013 06:50:05 +0000 (06:50 +0000)]
e1000e: cleanup: remove e1000e_commit_phy()
Remove the function e1000e_commit_phy() and replace the few calls to it
with the same function pointer that it would call. The function pointer is
almost always set for the devices that access these code paths so there is
no risk of a NULL pointer dereference; for the few instances where the
function pointer might not be set (i.e. can be called for the few devices
which do not have this function pointer set), check for a valid function
pointer.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Sat, 5 Jan 2013 08:06:24 +0000 (08:06 +0000)]
e1000e: cleanup: remove e1000_get_cable_length()
Remove the function e1000_get_cable_length() and replace the two calls
to it with the same function pointer that it would call.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Sat, 5 Jan 2013 08:06:19 +0000 (08:06 +0000)]
e1000e: cleanup: remove e1000_get_phy_cfg_done()
Remove the function e1000_get_phy_cfg_done() and replace the single call
to it with the same function pointer that it would call. The function
pointer is always set so there is no risk of a NULL pointer dereference.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Sat, 5 Jan 2013 08:06:14 +0000 (08:06 +0000)]
e1000e: cleanup: rename e1000_get_cfg_done()
In keeping with the e1000e driver function naming convention, the subject
function is renamed to indicate it is generic, i.e. it is applicable to
more than just a single MAC family (e.g. 80003es2lan, 82571, ich8lan).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function e1000_force_speed_duplex() and replace the single call
to it with the same function pointer that it would call. The function
pointer is always set so there is no risk of a NULL pointer dereference.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Sat, 5 Jan 2013 08:06:03 +0000 (08:06 +0000)]
e1000e: cleanup: remove e1000_set_d0_lplu_state()
Replace the function e1000_set_d0_lplu_state() with the contents of it
coded in place of the single call to the function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eric Dumazet [Fri, 25 Jan 2013 20:34:37 +0000 (20:34 +0000)]
net: fix possible wrong checksum generation
Pravin Shelar mentioned that GSO could potentially generate
wrong TX checksum if skb has fragments that are overwritten
by the user between the checksum computation and transmit.
He suggested to linearize skbs but this extra copy can be
avoided for normal tcp skbs cooked by tcp_sendmsg().
This patch introduces a new SKB_GSO_SHARED_FRAG flag, set
in skb_shinfo(skb)->gso_type if at least one frag can be
modified by the user.
Typical sources of such possible overwrites are {vm}splice(),
sendfile(), and macvtap/tun/virtio_net drivers.
Tested:
$ netperf -H 7.7.8.84
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
7.7.8.84 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 3959.52
$ netperf -H 7.7.8.84 -t TCP_SENDFILE
TCP SENDFILE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.8.84 ()
port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 3216.80
Performance of the SENDFILE is impacted by the extra allocation and
copy, and because we use order-0 pages, while the TCP_STREAM uses
bigger pages.
Reported-by: Pravin Shelar <pshelar@nicira.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Jan 2013 05:19:34 +0000 (00:19 -0500)]
Merge branch 'for-davem' of git://gitorious.org/linux-can/linux-can-next
Marc Kleine-Budde says:
====================
this is a pull-request for net-next/master. There is are 9 patches by
Fabio Baltieri and Kurt Van Dijck which add LED infrastructure and
support for CAN devices. Bernd Krumboeck adds a driver for the USB CAN
adapter from 8 devices. Oliver Hartkopp improves the CAN gateway
functionality. There are 4 patches by me, which clean up the CAN's
Kconfig.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Tue, 22 Jan 2013 21:09:51 +0000 (21:09 +0000)]
net: add RCU annotation to sk_dst_cache field
sock->sk_dst_cache is protected by RCU.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Tue, 22 Jan 2013 21:09:50 +0000 (21:09 +0000)]
decnet: use correct RCU API to deref sk_dst_cache field
sock->sk_dst_cache is protected by RCU, therefore we should
use __sk_dst_get() to deref it once we lock the sock.
This fixes several sparse warnings.
Cc: linux-decnet-user@lists.sourceforge.net Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai [Thu, 24 Jan 2013 01:54:19 +0000 (01:54 +0000)]
net/mlx4_en: Initialize RFS filters lock and list in init_netdev
filters_lock might have been used while it was re-initialized.
Moved filters_lock and filters_list initialization to init_netdev instead of
alloc_resources which is called every time the device is configured.
Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai [Thu, 24 Jan 2013 01:54:18 +0000 (01:54 +0000)]
net/mlx4_en: Fix a race when closing TX queue
There is a possible race where the TX completion handler can clean the
entire TX queue between the decision that the queue is full and actually
closing it. To avoid this situation, check again if the queue is really
full, if not, reopen the transmit and continue with sending the packet.
CC: Eric Dumazet <edumazet@google.com> Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com> Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Thu, 24 Jan 2013 01:54:17 +0000 (01:54 +0000)]
net/mlx4_core: Return proper error code when __mlx4_add_one fails
Returning 0 (success) when in fact we are aborting the load, leads to kernel
panic when unloading the module. Fix that by returning the actual error code.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx4_en: Use the correct netif lock on ndo_set_rx_mode
The device multicast list is protected by netif_addr_lock_bh in the networking core, we should
use this locking practice in mlx4_en too.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Yehezkel [Thu, 24 Jan 2013 01:54:15 +0000 (01:54 +0000)]
net/mlx4_en: Fix traffic loss under promiscuous mode
When port is stopped and flow steering mode is not device managed: promisc QP
rule wasn't removed from MCG table.
Added code to remove it in all flow steering modes.
In addition, promsic rule removal should be in stop port and not in start
port - moved it accordingly.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com> Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx4_en: Issue the dump eth statistics command under lock
Performing the DUMP_ETH_STATS firmware command outside the lock leads to kernel
panic when data structures such as RX/TX rings are freed in parallel, e.g when
one changes the mtu or ring sizes.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 24 Jan 2013 20:40:56 +0000 (20:40 +0000)]
irda: buffer overflow in irnet_ctrl_read()
The comments here say that the /* Max event is 61 char */ but in 2003 we
changed the event format and now the max event size is 75. The longest
event is:
There was a check to return -EOVERFLOW if the user gave us a "count"
value that was less than 64. Raising it to 75 might break backwards
compatability. Instead I removed the check and now it returns a
truncated string if "count" is too low.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Jan 2013 00:06:42 +0000 (19:06 -0500)]
Merge branch 'intel'
Jeff Kirsher says:
====================
This series contains updates to e1000e only. All the updates come
from Bruce Allan and most of the patch fix or enable features on
i217/i218. Most notably is patch 03 "e1000e: add support for IEEE-1588
PTP", which is v2 of the patch based on feedback from Stephen Hemminger.
Also patch 04 "e1000e: enable ECC on I217/I218 to catch packet buffer
memory errors" should be queued up for stable (as well as net) trees, but
the patch does not apply cleanly to either of those trees currently.
So I will work with Bruce to provide a version of the patch which will
apply cleanly to net (and stable) and we can queue it up at that point
for stable 3.5 tree.
The remaining patches are general cleanups of the code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Sat, 5 Jan 2013 05:08:37 +0000 (05:08 +0000)]
e1000e: cleanup: do not assign a variable a value when not necessary
Static analysis with cppcheck has shown a few instances of a variable
being reassigned a value before the old one has been used. None of these
ever require the old value to be used so remove the old values.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Sat, 5 Jan 2013 05:08:31 +0000 (05:08 +0000)]
e1000e: do not ignore variables which get set a value
Static analysis with cppcheck has shown a few instances of a variable which
is assigned a value that is never used. A number of these are the return
status of various driver function calls which should be passed back to the
caller of the current function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Sat, 5 Jan 2013 03:06:54 +0000 (03:06 +0000)]
e1000e: cleanup: remove unnecessary function prototypes
...and cleanup some whitespace in other prototypes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Fri, 4 Jan 2013 10:06:03 +0000 (10:06 +0000)]
e1000e: add comment to spinlock_t definition
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Fri, 4 Jan 2013 09:54:11 +0000 (09:54 +0000)]
e1000e: remove definition of struct which is no longer used
The e1000e driver has been converted to use extended descriptors instead of
the older legacy descriptor type.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Fri, 4 Jan 2013 09:53:19 +0000 (09:53 +0000)]
e1000e: fix PHY init workarounds for i217/i218
Toggling the LANPHYPC Value bit cycles the power on the PHY and sets it
back to power-on defaults. This includes setting it's MAC-PHY messaging
mode to use the PCIe-like interconnect, so the MAC must also be set back
from SMBus mode to PCIe mode otherwise the PHY can be inaccessible.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Fri, 4 Jan 2013 09:51:36 +0000 (09:51 +0000)]
e1000e: correct maximum frame size on i217/i218
The largest jumbo frame supported by the i217 and i218 hardware is 9018.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Tue, 1 Jan 2013 16:00:01 +0000 (16:00 +0000)]
e1000e: update copyright date
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Sat, 29 Dec 2012 09:08:50 +0000 (09:08 +0000)]
e1000e: remove prototype of non-existent function
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Wed, 12 Dec 2012 04:45:51 +0000 (04:45 +0000)]
e1000e: prevent hardware from automatically configuring PHY on I217/I218
As done with the previous generation managed 82579, prevent the PHY from
being put into an unknown state by blocking the hardware from automatically
configuring the PHY as done with the previous generation managed 82579.
Instead, the driver should configure the PHY with contents of the EEPROM
image.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Wed, 23 Jan 2013 09:00:03 +0000 (09:00 +0000)]
e1000e: enable ECC on I217/I218 to catch packet buffer memory errors
In rare instances, memory errors have been detected in the internal packet
buffer memory on I217/I218 when stressed under certain environmental
conditions. Enable Error Correcting Code (ECC) in hardware to catch both
correctable and uncorrectable errors. Correctable errors will be handled
by the hardware. Uncorrectable errors in the packet buffer will cause the
packet to be received with an error indication in the buffer descriptor
causing the packet to be discarded. If the uncorrectable error is in the
descriptor itself, the hardware will stop and interrupt the driver
indicating the error. The driver will then reset the hardware in order to
clear the error and restart.
Both types of errors will be accounted for in statistics counters.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Sat, 19 Jan 2013 01:09:58 +0000 (01:09 +0000)]
e1000e: add support for IEEE-1588 PTP
Add PTP IEEE-1588 support and make accesible via the PHC subsystem.
v2: make e1000e_ptp_clock_info a static const struct per Stephen Hemminger
Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Reviewed-by: Jacob Keller <Jacob.e.keller@intel.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Sat, 8 Dec 2012 00:35:35 +0000 (00:35 +0000)]
e1000e: fix flow-control thresholds for jumbo frames on 82579/I217/I218
The previous static flow-control thresholds were causing unnecessary pause
packets to be transmitted when jumbo frames are configured reducing the
throughput.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Wed, 5 Dec 2012 06:25:36 +0000 (06:25 +0000)]
e1000e: fix ethtool offline register test for I217
The SHRAH[9] register on I217 has a different R/W bit-mask than RAR and
SHRAL/H registers. Set R/W bit-mask appropriately for SHRAH[9] when
testing the R/W ability of the register. Also, fix the error message log
format so that it does not provide misleading information (i.e. the logged
register address could be incorrect).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tom Herbert [Sat, 26 Jan 2013 07:50:54 +0000 (07:50 +0000)]
soreuseport: fix use of uid in tb->fastuid
Fix a reported compilation error where ia variable of type kuid_t
was being set to zero.
Eliminate two instances of setting tb->fastuid to zero. tb->fastuid is
only used if tb->fastreuseport is set, so there should be no problem if
tb->fastuid is not initialized (when tb->fastreuesport is zero).
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf [Fri, 25 Jan 2013 00:00:58 +0000 (00:00 +0000)]
Remove leftover #endif after introducing SO_REUSEPORT
Commit 055dc21a1d (soreuseport: infrastructure) removed the #if 0
around SO_REUSEPORT without removing the corresponding #endif
thus causing the header guard to close early.
Cc: Tom Herbert <therbert@google.com> Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish chopra [Fri, 25 Jan 2013 10:20:37 +0000 (10:20 +0000)]
qlcnic: avoid mixed mode interrupts for some adapter types
o Some adapter types do not support co-existence of Legacy Interrupt with
MSI-x or MSI among multiple functions. For those adapters, prevent attaching
to a function during normal load, if MSI-x or MSI vectors are not available.
o Using module parameters use_msi=0 and use_msi_x=0, driver can be loaded in
legacy mode for all functions in the adapter.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 27 Jan 2013 05:56:10 +0000 (00:56 -0500)]
Merge branch 'master' of git://1984.lsi.us.es/nf-next
Pablo Neira Ayuso says:
====================
This batch contains netfilter updates for you net-next tree, they are:
* The new connlabel extension for x_tables, that allows us to attach
labels to each conntrack flow. The kernel implementation uses a
bitmask and there's a file in user-space that maps the bits with the
corresponding string for each existing label. By now, you can attach
up to 128 overlapping labels. From Florian Westphal.
* A new round of improvements for the netns support for conntrack.
Gao feng has moved many of the initialization code of each module
of the netns init path. He also made several code refactoring, that
code looks cleaner to me now.
* Added documentation for all possible tweaks for nf_conntrack via
sysctl, from Jiri Pirko.
* Cisco 7941/7945 IP phone support for our SIP conntrack helper,
from Kevin Cernekee.
* Missing header file in the snmp helper, from Stephen Hemminger.
* Finally, a couple of fixes to resolve minor issues with these
changes, from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Thu, 17 Jan 2013 17:43:44 +0000 (18:43 +0100)]
can: gw: add a variable limit for CAN frame routings
To prevent a possible misconfiguration (e.g. circular CAN frame routings)
limit the number of routings of a single CAN frame to a small variable value.
The limit can be specified by the module parameter 'max_hops' (1..6).
The default value is 1 (one hop), according to the original can-gw behaviour.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Thu, 17 Jan 2013 17:43:41 +0000 (18:43 +0100)]
can: gw: make routing to the incoming CAN interface configurable
Introduce new configuration flag CGW_FLAGS_CAN_IIF_TX_OK to configure if a
CAN sk_buff that has been routed with can-gw is allowed to be send back to
the originating CAN interface.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Thu, 17 Jan 2013 17:43:39 +0000 (18:43 +0100)]
can: add private data space for CAN sk_buffs
The struct can_skb_priv is used to transport additional information along
with the stored struct can(fd)_frame that can not be contained in existing
struct sk_buff elements.
can_skb_priv is located in the skb headroom, which does not touch the existing
CAN sk_buff usage with skb->data and skb->len, so that even out-of-tree
CAN drivers can be used without changes.
Btw. out-of-tree CAN drivers without can_skb_priv in the sk_buff headroom
would not support features based on can_skb_priv.
The can_skb_priv->ifindex contains the first interface where the CAN frame
appeared on the local host. Unfortunately skb->skb_iif can not be used as this
value is overwritten in every netif_receive_skb() call.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fabio Baltieri [Tue, 18 Dec 2012 17:51:03 +0000 (18:51 +0100)]
can: sja1000: add LED trigger support
Add support for canbus activity led indicators on sja1000 devices by
calling appropriate can_led functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fabio Baltieri [Tue, 18 Dec 2012 17:51:02 +0000 (18:51 +0100)]
can: mcp251x: add LED trigger support
Add support for canbus activity led indicators on mcp251x devices by
calling appropriate can_led functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Cc: Christian Pellegrin <chripell@fsfe.org> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fabio Baltieri [Tue, 18 Dec 2012 17:50:58 +0000 (18:50 +0100)]
can: flexcan: add LED trigger support
Add support for canbus activity led indicators on flexcan devices by
calling appropriate can_led_* functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Kurt Van Dijck [Tue, 18 Dec 2012 17:50:57 +0000 (18:50 +0100)]
can: rename LED trigger name on netdev renames
The LED trigger name for CAN devices is based on the initial
CAN device name, but does never change. The LED trigger name
is not guaranteed to be unique in case of hotplugging CAN devices.
This patch tries to address this problem by modifying the
LED trigger name according to the CAN device name when
the latter changes.
v1 - Kurt Van Dijck
v2 - Fabio Baltieri
- remove rename blocking if trigger is bound
- use led-subsystem function for the actual rename (still WiP)
- call init/exit functions from dev.c
v3 - Kurt Van Dijck
- safe operation for non-candev based devices (vcan, slcan)
based on earlier patch
v4 - Kurt Van Dijck
- trivial patch mistakes fixed
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Kurt Van Dijck [Tue, 18 Dec 2012 17:50:56 +0000 (18:50 +0100)]
can: export a safe netdev_priv wrapper for candev
In net_device notifier calls, it was impossible to determine
if a CAN device is based on candev in a safe way.
This patch adds such test in order to access candev storage
from within those notifiers.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fabio Baltieri [Tue, 18 Dec 2012 17:50:55 +0000 (18:50 +0100)]
can: add tx/rx LED trigger support
This patch implements the functions to add two LED triggers, named
<ifname>-tx and <ifname>-rx, to a canbus device driver.
Triggers are called from specific handlers by each CAN device driver and
can be disabled altogether with a Kconfig option.
The implementation keeps the LED on when the interface is UP and blinks
the LED on network activity at a configurable rate.
This only supports can-dev based drivers, as it uses some support field
in the can_priv structure.
Supported drivers should call devm_can_led_init() and can_led_event() as
needed.
Cleanup is handled automatically by devres, so no *_exit function is
needed.
Supported events are:
- CAN_LED_EVENT_OPEN: turn on tx/rx LEDs
- CAN_LED_EVENT_STOP: turn off tx/rx LEDs
- CAN_LED_EVENT_TX: trigger tx LED blink
- CAN_LED_EVENT_RX: trigger tx LED blink
Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Bernd Krumboeck [Sat, 19 Jan 2013 06:30:45 +0000 (07:30 +0100)]
can: usb_8dev: Add support for USB2CAN interface from 8 devices
Add device driver for USB2CAN interface from "8 devices" (http://www.8devices.com).
changes since v10:
* small cleanups
changes since v9:
* fixed syslog messages
* fixed crc error number
* increased MAX_RX_URBS and MAX_TX_URBS
changes since v8:
* remove all sysfs files
changes since v7:
* add sysfs documentation
* fix minor styling issue
* fixed can state for passive mode
* changed handling for crc errors
changes since v6:
* changed some variable types to big endian equivalent
* small cleanups
changes since v5:
* unlock mutex on error
changes since v4:
* removed FSF address
* renamed struct usb_8dev
* removed unused variable free_slots
* replaced some _to_cpu functions with pointer equivalent
* fix return value for usb_8dev_set_mode
* handle can errors with separate function
* fix overrun error handling
* rewrite error handling for usb_8dev_start_xmit
* fix urb submit in usb_8dev_start
* various small fixes
Acked-by: Wolfgang Grandegger <wg@grandegger.com> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Bernd Krumboeck <krumboeck@universalnet.at> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can: Kconfig: convert 'depends on CAN_DEV' into 'if CAN_DEV...endif' block
This patch adds an 'if CAN_DEV...endif' Block around the CAN driver
symbols in drivers/net/can/Kconfig. So the 'depends on CAN' dependencies
can be removed.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Donald Dutile [Tue, 11 Dec 2012 08:26:48 +0000 (08:26 +0000)]
ixgbe: Limit number of reported VFs to device specific value
ixgbe claims it supports 64 VFs in its SRIOV capability
structure, but the driver only supports 63. Adjust it
so sysfs sriov configuration checking will check with
the proper totalvf value.
Signed-off-by: Donald Dutile <ddutile@redhat.com> Acked-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement callbacks in the driver for the new PCI bus driver
interface that allows the user to enable/disable SR-IOV VFs
in a device via the sysfs interface.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com> CC: Don Dutile <ddutile@redhat.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Greg Rose [Tue, 11 Dec 2012 08:26:38 +0000 (08:26 +0000)]
ixgbe: Modularize SR-IOV enablement code
In preparation for enable/disable of SR-IOV via the PCI sysfs interface
move some core SR-IOV enablement code that would be common to module
parameter usage or callback from the PCI bus driver to a separate
function so that it can be used by either method.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com> CC: Don Dutile <ddutile@redhat.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by: Sibai Li <Sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Greg Rose [Tue, 11 Dec 2012 08:26:33 +0000 (08:26 +0000)]
ixgbe: Make mailbox ops initialization unconditional
There is no actual dependency on initialization of the mailbox ops on
whether SR-IOV is enabled or not and it doesn't hurt to go ahead and
initialize ops unconditionally. Move the initialization into the device
probe so that the mailbox ops are initialized at the time we have the
board info necessary to do it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com> CC: Don Dutile <ddutile@redhat.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by: Sibai Li <Sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Sat, 8 Dec 2012 09:04:25 +0000 (09:04 +0000)]
ixgbe: only compile ixgbe_debugfs.o when enabled
This patch modifies ixgbe_debugfs.c and the Makefile for the ixgbe
driver to only compile the file when the config is enabled. This means
we can remove the #ifdef inside the ixgbe_debugfs.c file.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
projects / linux-beck.git / log