Santiago Leon [Tue, 4 Sep 2012 14:41:37 +0000 (14:41 +0000)]
ibmveth: Fix alignment of rx queue bug
This patch fixes a bug found by Nish Aravamudan
(https://lkml.org/lkml/2012/5/15/220) where the driver is not following
the spec (it is not aligning the rx buffer on a 16-byte boundary) and the
hypervisor aborts the registration, making the device unusable.
The fix follows BenH's recommendation (https://lkml.org/lkml/2012/7/20/461)
to replace the kmalloc+map for a single call to dma_alloc_coherent()
because that function always aligns to a 16-byte boundary.
The stable trees will run into this bug whenever the rx buffer kmalloc call
returns something not aligned on a 16-byte boundary.
Cc: <stable@vger.kernel.org> Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: fix possible socket refcount problem for ipv6
commit 144d56e91044181ec0ef67aeca91e9a8b5718348
("tcp: fix possible socket refcount problem") is missing
the IPv6 part. As tcp_release_cb is shared by both protocols
we should hold sock reference for the TCP_MTU_REDUCED_DEFERRED
bit.
Signed-off-by: Julian Anastasov <ja@ssi.bg> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 5 Sep 2012 19:11:18 +0000 (15:11 -0400)]
Merge branch 'fixes-for-3.6' of git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
this patch is for the v3.6 release cycle. Benoît Locher fixed a repeated frame
bug in the mcp251x driver. He implemented the workaround suggested by the
errata sheet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
powerpc: Don't use __put_user() in patch_instruction
patch_instruction() can be called very early on ppc32, when the kernel
isn't yet running at it's linked address. That can cause the !
is_kernel_addr() test in __put_user() to trip and call might_sleep()
which is very bad at that point during boot.
Use a lower level function instead for now, at least until we get to
rework ppc32 boot process to do the code patching later, like ppc64
does.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras [Tue, 4 Sep 2012 18:33:08 +0000 (18:33 +0000)]
powerpc: Make sure IPI handlers see data written by IPI senders
We have been observing hangs, both of KVM guest vcpu tasks and more
generally, where a process that is woken doesn't properly wake up and
continue to run, but instead sticks in TASK_WAKING state. This
happens because the update of rq->wake_list in ttwu_queue_remote()
is not ordered with the update of ipi_message in
smp_muxed_ipi_message_pass(), and the reading of rq->wake_list in
scheduler_ipi() is not ordered with the reading of ipi_message in
smp_ipi_demux(). Thus it is possible for the IPI receiver not to see
the updated rq->wake_list and therefore conclude that there is nothing
for it to do.
In order to make sure that anything done before smp_send_reschedule()
is ordered before anything done in the resulting call to scheduler_ipi(),
this adds barriers in smp_muxed_message_pass() and smp_ipi_demux().
The barrier in smp_muxed_message_pass() is a full barrier to ensure that
there is a full ordering between the smp_send_reschedule() caller and
scheduler_ipi(). In smp_ipi_demux(), we use xchg() rather than
xchg_local() because xchg() includes release and acquire barriers.
Using xchg() rather than xchg_local() makes sense given that
ipi_message is not just accessed locally.
This moves the barrier between setting the message and calling the
cause_ipi() function into the individual cause_ipi implementations.
Most of them -- those that used outb, out_8 or similar -- already had
a full barrier because out_8 etc. include a sync before the MMIO
store. This adds an explicit barrier in the two remaining cases.
These changes made no measurable difference to the speed of IPIs as
measured using a simple ping-pong latency test across two CPUs on
different cores of a POWER7 machine.
The analysis of the reason why processes were not waking up properly
is due to Milton Miller.
Cc: stable@vger.kernel.org # v3.0+ Reported-by: Milton Miller <miltonm@bga.com> Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Mon, 3 Sep 2012 16:51:10 +0000 (16:51 +0000)]
powerpc: Restore correct DSCR in context switch
During a context switch we always restore the per thread DSCR value.
If we aren't doing explicit DSCR management
(ie thread.dscr_inherit == 0) and the default DSCR changed while
the process has been sleeping we end up with the wrong value.
Check thread.dscr_inherit and select the default DSCR or per thread
DSCR as required.
This was found with the following test case, when running with
more threads than CPUs (ie forcing context switching):
Anton Blanchard [Mon, 3 Sep 2012 16:49:47 +0000 (16:49 +0000)]
powerpc: Fix DSCR inheritance in copy_thread()
If the default DSCR is non zero we set thread.dscr_inherit in
copy_thread() meaning the new thread and all its children will ignore
future updates to the default DSCR. This is not intended and is
a change in behaviour that a number of our users have hit.
We just need to inherit thread.dscr and thread.dscr_inherit from
the parent which ends up being much simpler.
Anton Blanchard [Mon, 3 Sep 2012 16:48:46 +0000 (16:48 +0000)]
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
When we update the DSCR either via emulation of mtspr(DSCR) or via
a change to dscr_default in sysfs we don't update thread.dscr.
We will eventually update it at context switch time but there is
a period where thread.dscr is incorrect.
If we fork at this point we will copy the old value of thread.dscr
into the child. To avoid this, always keep thread.dscr in sync with
reality.
Anton Blanchard [Mon, 3 Sep 2012 16:47:56 +0000 (16:47 +0000)]
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
Writing to dscr_default in sysfs doesn't actually change the DSCR -
we rely on a context switch on each CPU to do the work. There is no
guarantee we will get a context switch in a reasonable amount of time
so fire off an IPI to force an immediate change.
This issue was found with the following test case:
Paul Mackerras [Thu, 26 Jul 2012 18:51:09 +0000 (18:51 +0000)]
powerpc/powernv: Always go into nap mode when CPU is offline
The CPU hotplug code for the powernv platform currently only puts
offline CPUs into nap mode if the powersave_nap variable is set.
However, HV-style KVM on this platform requires secondary CPU threads
to be offline and in nap mode. Since we know nap mode works just
fine on all POWER7 machines, and the only machines that support the
powernv platform are POWER7 machines, this changes the code to
always put offline CPUs into nap mode, regardless of powersave_nap.
Powersave_nap still controls whether or not CPUs go into nap mode
when idle, as before.
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras [Thu, 26 Jul 2012 13:56:11 +0000 (13:56 +0000)]
powerpc: Give hypervisor decrementer interrupts their own handler
At the moment the handler for hypervisor decrementer interrupts is
the same as for decrementer interrupts, i.e. timer_interrupt().
This is bogus; if we ever do get a hypervisor decrementer interrupt
it won't have anything to do with the next timer event. In fact
the only time we get hypervisor decrementer interrupts is when one
is left pending on exit from a KVM guest.
When we get a hypervisor decrementer interrupt we don't need to do
anything special to clear it, since they are edge-triggered on the
transition of HDEC from 0 to -1. Thus this adds an empty handler
function for them. We don't need to have them masked when interrupts
are soft-disabled, so we use STD_EXCEPTION_HV instead of
MASKABLE_EXCEPTION_HV.
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In znet_probe(), strncmp() may access beyond 0x100000 and
trigger the below oops in kvm. Fix it by limiting the loop
under 0x100000-8. I suspect the limit could be further decreased
to 0x100000-sizeof(struct netidblk), however no datasheet at hand..
xfrm: Workaround incompatibility of ESN and async crypto
ESN for esp is defined in RFC 4303. This RFC assumes that the
sequence number counters are always up to date. However,
this is not true if an async crypto algorithm is employed.
If the sequence number counters are not up to date on sequence
number check, we may incorrectly update the upper 32 bit of
the sequence number. This leads to a DOS.
We workaround this by comparing the upper sequence number,
(used for authentication) with the upper sequence number
computed after the async processing. We drop the packet
if these numbers are different.
To do this, we introduce a recheck function that does this
check in the ESN case.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan encapsulation fields in the maximum flow defintion were
never updated when the representation changed before upstreaming.
In theory this could cause a kernel panic when a maximum length
flow is used. In practice this has never happened (to my knowledge)
because skb allocations are padded out to a cache line so you would
need the right combination of flow and packet being sent to userspace.
Eric Dumazet [Sat, 1 Sep 2012 03:19:57 +0000 (03:19 +0000)]
fq_codel: dont reinit flow state
When fq_codel builds a new flow, it should not reset codel state.
Codel algo needs to get previous values (lastcount, drop_next) to get
proper behavior.
Signed-off-by: Dave Taht <dave.taht@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Dave Taht <dave.taht@bufferbloat.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Benoît Locher [Mon, 27 Aug 2012 13:02:45 +0000 (15:02 +0200)]
can: mcp251x: avoid repeated frame bug
The MCP2515 has a silicon bug causing repeated frame transmission, see section
5 of MCP2515 Rev. B Silicon Errata Revision G (March 2007).
Basically, setting TXBnCTRL.TXREQ in either SPI mode (00 or 11) will eventually
cause the bug. The workaround proposed by Microchip is to use mode 00 and send
a RTS command on the SPI bus to initiate the transmission.
Cc: <stable@vger.kernel.org> Signed-off-by: Benoît Locher <Benoit.Locher@skf.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Suspending an open usbnet device results in constant
rescheduling of usbnet_bh.
commit 65841fd5 "usbnet: handle remote wakeup asap"
refactored the usbnet_bh code to allow sharing the
urb allocate and submit code with usbnet_resume. In
this process, a test for, and immediate return on,
ENOLINK from rx_submit was unintentionally dropped.
The rx queue will not grow if rx_submit fails,
making usbnet_bh reschedule itself. This results
in a softirq storm if the error is persistent.
rx_submit translates the usb_submit_urb error
EHOSTUNREACH into ENOLINK, so this is an expected
and persistent error for a suspended device. The
old code tested for this condition and avoided
rescheduling. Putting this test back.
Cc: <stable@vger.kernel.org> # v3.5 Cc: Ming Lei <ming.lei@canonical.com> Cc: Oliver Neukum <oneukum@suse.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf [Mon, 3 Sep 2012 04:27:42 +0000 (04:27 +0000)]
sctp: Don't charge for data in sndbuf again when transmitting packet
SCTP charges wmem_alloc via sctp_set_owner_w() in sctp_sendmsg() and via
skb_set_owner_w() in sctp_packet_transmit(). If a sender runs out of
sndbuf it will sleep in sctp_wait_for_sndbuf() and expects to be waken up
by __sctp_write_space().
Buffer space charged via sctp_set_owner_w() is released in sctp_wfree()
which calls __sctp_write_space() directly.
Buffer space charged via skb_set_owner_w() is released via sock_wfree()
which calls sk->sk_write_space() _if_ SOCK_USE_WRITE_QUEUE is not set.
sctp_endpoint_init() sets SOCK_USE_WRITE_QUEUE on all sockets.
Therefore if sctp_packet_transmit() manages to queue up more than sndbuf
bytes, sctp_wait_for_sndbuf() will never be woken up again unless it is
interrupted by a signal.
This could be fixed by clearing the SOCK_USE_WRITE_QUEUE flag but ...
Charging for the data twice does not make sense in the first place, it
leads to overcharging sndbuf by a factor 2. Therefore this patch only
charges a single byte in wmem_alloc when transmitting an SCTP packet to
ensure that the socket stays alive until the packet has been released.
This means that control chunks are no longer accounted for in wmem_alloc
which I believe is not a problem as skb->truesize will typically lead
to overcharging anyway and thus compensates for any control overhead.
Signed-off-by: Thomas Graf <tgraf@suug.ch> CC: Vlad Yasevich <vyasevic@redhat.com> CC: Neil Horman <nhorman@tuxdriver.com> CC: David Miller <davem@davemloft.net> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1) NLA_PUT* --> nla_put_* conversion got one case wrong in
nfnetlink_log, fix from Patrick McHardy.
2) Missed error return check in ipw2100 driver, from Julia Lawall.
3) PMTU updates in ipv4 were setting the expiry time incorrectly, fix
from Eric Dumazet.
4) SFC driver erroneously reversed src and dst when reporting filters
via ethtool.
5) Memory leak in CAN protocol and wrong setting of IRQF_SHARED in
sja1000 can platform driver, from Alexey Khoroshilov and Sven
Schmitt.
6) Fix multicast traffic scaling regression in ipv4_dst_destroy, only
take the lock when we really need to. From Eric Dumazet.
7) Fix non-root process spoofing in netlink, from Pablo Neira Ayuso.
8) CWND reduction in TCP is done incorrectly during non-SACK recovery,
fix from Yuchung Cheng.
9) Revert netpoll change, and fix what was actually a driver specific
problem. From Amerigo Wang. This should cure bootup hangs with
netconsole some people reported.
10) Fix xen-netfront invoking __skb_fill_page_desc() with a NULL page
pointer. From Ian Campbell.
11) SIP NAT fix for expectiontation creation, from Pablo Neira Ayuso.
12) __ip_rt_update_pmtu() needs RCU locking, from Eric Dumazet.
13) Fix usbnet deadlock on resume, can't use GFP_KERNEL in this
situation. From Oliver Neukum.
14) The davinci ethernet driver triggers an OOPS on removal because it
frees an MDIO object before unregistering it. Fix from Bin Liu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
net: qmi_wwan: add several new Gobi devices
fddi: 64 bit bug in smt_add_para()
net: ethernet: fix kernel OOPS when remove davinci_mdio module
net/xfrm/xfrm_state.c: fix error return code
net: ipv6: fix error return code
net: qmi_wwan: new device: Foxconn/Novatel E396
usbnet: fix deadlock in resume
cs89x0 : packet reception not working
netfilter: nf_conntrack: fix racy timer handling with reliable events
bnx2x: Correct the ndo_poll_controller call
bnx2x: Move netif_napi_add to the open call
ipv4: must use rcu protection while calling fib_lookup
bnx2x: fix 57840_MF pci id
net: ipv4: ipmr_expire_timer causes crash when removing net namespace
e1000e: DoS while TSO enabled caused by link partner with small MSS
l2tp: avoid to use synchronize_rcu in tunnel free function
gianfar: fix default tx vlan offload feature flag
netfilter: nf_nat_sip: fix incorrect handling of EBUSY for RTCP expectation
xen-netfront: use __pskb_pull_tail to ensure linear area is big enough on RX
netfilter: nfnetlink_log: fix error return code in init path
...
Gobi devices are composite, needing both the qcserial and
qmi_wwan drivers to support all functions. Re-syncing the
list of supported devices with qcserial.
Cc: Aleksander Morgado <aleksander@lanedo.com> Cc: Thomas Tuttle <ttuttle@chromium.org> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@tempietto.lan>
Dan Carpenter [Sat, 1 Sep 2012 09:57:40 +0000 (09:57 +0000)]
fddi: 64 bit bug in smt_add_para()
The intent was to set 4 bytes of data so that's why the sp_len is set
to 4 on the next line. The cast to u_long pointer clears 8 bytes
on 64 bit arches.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@tempietto.lan>
John Stultz [Fri, 31 Aug 2012 17:30:06 +0000 (13:30 -0400)]
time: Move ktime_t overflow checking into timespec_valid_strict
Andreas Bombe reported that the added ktime_t overflow checking added to
timespec_valid in commit 4e8b14526ca7 ("time: Improve sanity checking of
timekeeping inputs") was causing problems with X.org because it caused
timeouts larger then KTIME_T to be invalid.
Previously, these large timeouts would be clamped to KTIME_MAX and would
never expire, which is valid.
This patch splits the ktime_t overflow checking into a new
timespec_valid_strict function, and converts the timekeeping codes
internal checking to use this more strict function.
Reported-and-tested-by: Andreas Bombe <aeb@debian.org> Cc: Zhouping Liu <zliu@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
Pull PARISC fixes from James Bottomley:
"This is a set of two bug fixes. One is the ATOMIC problem which is
now causing a compile failure in certain situations. The other is
mishandling of PER_LINUX32 which may also cause user visible effects.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] fix personality flag check in copy_thread()
[PARISC] Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A couple of s390 bug fixes for 3.5-rc4"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/32: Don't clobber personality flags on exec
s390/smp: add missing smp_store_status() for !SMP
s390/dasd: fix ioctl return value
s390: Always use "long" for ssize_t to match size_t
Cc: Dan Williams <dcbw@redhat.com> Cc: Bjørn Mork <bjorn@mork.no> Cc: Ben Chan <benchan@google.com> Signed-off-by: Aleksander Morgado <aleksander@lanedo.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Neukum [Sun, 26 Aug 2012 20:41:38 +0000 (20:41 +0000)]
usbnet: fix deadlock in resume
A usbnet device can share a multifunction device
with a storage device. If the storage device is autoresumed
the usbnet devices also needs to be autoresumed. Allocating
memory with GFP_KERNEL can deadlock in this case.
Commit 68e67f40b ("ALSA: snd-usb: move calls to usb_set_interface")
saved us some unnecessary calls to snd_usb_set_interface() but ignored
the fact that there is at least one device out there which operates on
two endpoint in different interfaces simultaniously.
Take care for this by catching the case where data and sync endpoints
are located on different interfaces and calling snd_usb_set_interface()
between the start of the two endpoints.
Signed-off-by: Daniel Mack <zonque@gmail.com> Reported-by: Robert M. Albrecht <linux@romal.de> Cc: stable@kernel.org [v3.5+] Signed-off-by: Takashi Iwai <tiwai@suse.de>
Daniel Mack [Thu, 30 Aug 2012 16:52:30 +0000 (18:52 +0200)]
ALSA: snd-usb: fix calls to next_packet_size
In order to support devices with implicit feedback streaming models,
packet sizes are now stored with each individual urb, and the PCM
handling code which fills the buffers purely relies on the size fields
now.
However, calling snd_usb_audio_next_packet_size() for all possible
packets in an URB at once, prior to letting the PCM code do its job
does in fact not lead to the same behaviour than what the old code did:
The PCM code will break its loop once a period boundary is reached,
consequently using up less packets that it really could.
As snd_usb_audio_next_packet_size() implements a feedback mechanism to
the endpoints phase accumulator, the number of calls to that function
matters, and when called too often, the data rate runs out of bounds.
Fix this by making the next_packet function public, and call it from the
PCM code as before if the packet data sizes are not defined.
Daniel Mack [Thu, 30 Aug 2012 16:52:29 +0000 (18:52 +0200)]
ALSA: snd-usb: restore delay information
Parts of commit 294c4fb8 ("ALSA: usb: refine delay information with USB
frame counter") were unfortunately lost during the refactoring of the
snd-usb driver in 3.5.
This patch adds them back, restoring the correct delay information
behaviour.
netfilter: nf_conntrack: fix racy timer handling with reliable events
Existing code assumes that del_timer returns true for alive conntrack
entries. However, this is not true if reliable events are enabled.
In that case, del_timer may return true for entries that were
just inserted in the dying list. Note that packets / ctnetlink may
hold references to conntrack entries that were just inserted to such
list.
This patch fixes the issue by adding an independent timer for
event delivery. This increases the size of the ecache extension.
Still we can revisit this later and use variable size extensions
to allocate this area on demand.
Tested-by: Oliver Smith <olipro@8.c.9.b.0.7.4.0.1.0.0.2.ip6.arpa> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Merav Sicron [Mon, 27 Aug 2012 03:26:19 +0000 (03:26 +0000)]
bnx2x: Move netif_napi_add to the open call
Move netif_napi_add for all queues from the probe call to the open call, to
avoid the case that napi objects are added for queues that may eventually not
be initialized and activated. With the former behavior, the driver could crash
when netpoll was calling ndo_poll_controller.
Signed-off-by: Merav Sicron <meravs@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 26 Aug 2012 00:35:45 +0000 (00:35 +0000)]
bnx2x: fix 57840_MF pci id
Commit c3def943c7117d42caaed3478731ea7c3c87190e have added support for
new pci ids of the 57840 board, while failing to change the obsolete value
in 'pci_ids.h'.
This patch does so, allowing the probe of such devices.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ipv4: ipmr_expire_timer causes crash when removing net namespace
When tearing down a net namespace, ipv4 mr_table structures are freed
without first deactivating their timers. This can result in a crash in
run_timer_softirq.
This patch mimics the corresponding behaviour in ipv6.
Locking and synchronization seem to be adequate.
We are about to kfree mrt, so existing code should already make sure that
no other references to mrt are pending or can be created by incoming traffic.
The functions invoked here do not cause new references to mrt or other
race conditions to be created.
Invoking del_timer_sync guarantees that ipmr_expire_timer is inactive.
Both ipmr_expire_process (whose completion we may have to wait in
del_timer_sync) and mroute_clean_tables internally use mfc_unres_lock
or other synchronizations when needed, and they both only modify mrt.
Tested in Linux 3.4.8.
Signed-off-by: Francesco Ruggeri <fruggeri@aristanetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Fri, 24 Aug 2012 20:38:11 +0000 (20:38 +0000)]
e1000e: DoS while TSO enabled caused by link partner with small MSS
With a low enough MSS on the link partner and TSO enabled locally, the
networking stack can periodically send a very large (e.g. 64KB) TCP
message for which the driver will attempt to use more Tx descriptors than
are available by default in the Tx ring. This is due to a workaround in
the code that imposes a limit of only 4 MSS-sized segments per descriptor
which appears to be a carry-over from the older e1000 driver and may be
applicable only to some older PCI or PCIx parts which are not supported in
e1000e. When the driver gets a message that is too large to fit across the
configured number of Tx descriptors, it stops the upper stack from queueing
any more and gets stuck in this state. After a timeout, the upper stack
assumes the adapter is hung and calls the driver to reset it.
Remove the unnecessary limitation of using up to only 4 MSS-sized segments
per Tx descriptor, and put in a hard failure test to catch when attempting
to check for message sizes larger than would fit in the whole Tx ring.
Refactor the remaining logic that limits the size of data per Tx descriptor
from a seemingly arbitrary 8KB to a limit based on the dynamic size of the
Tx packet buffer as described in the hardware specification.
Also, fix the logic in the check for space in the Tx ring for the next
largest possible packet after the current one has been successfully queued
for transmit, and use the appropriate defines for default ring sizes in
e1000_probe instead of magic values.
This issue goes back to the introduction of e1000e in 2.6.24 when it was
split off from e1000.
Reported-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Cc: Stable <stable@vger.kernel.org> [2.6.24+] Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Thu, 23 Aug 2012 21:46:25 +0000 (21:46 +0000)]
gianfar: fix default tx vlan offload feature flag
Commit -
"b852b72 gianfar: fix bug caused by 87c288c6e9aa31720b72e2bc2d665e24e1653c3e"
disables by default (on mac init) the hw vlan tag insertion.
The "features" flags were not updated to reflect this, and
"ethtool -K" shows tx-vlan-offload to be "on" by default.
Cc: Sebastian Poehn <sebastian.poehn@belden.com> Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ian Campbell [Wed, 22 Aug 2012 00:26:47 +0000 (00:26 +0000)]
xen-netfront: use __pskb_pull_tail to ensure linear area is big enough on RX
I'm slightly concerned by the "only in exceptional circumstances"
comment on __pskb_pull_tail but the structure of an skb just created
by netfront shouldn't hit any of the especially slow cases.
This approach still does slightly more work than the old way, since if
we pull up the entire first frag we now have to shuffle everything
down where before we just received into the right place in the first
place.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Mel Gorman <mgorman@suse.de> Cc: xen-devel@lists.xensource.com Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 30 Aug 2012 16:11:33 +0000 (09:11 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A bunch of scattered fixes ati/intel/nouveau, couple of core ones,
nothing too shocking or different."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S
gma500: Consider CRTC initially active.
drm/radeon: fix dig encoder selection on DCE61
drm/radeon: fix double free in radeon_gpu_reset
drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
drm/radeon: rework panel mode setup
drm/radeon/atom: powergating fixes for DCE6
drm/radeon/atom: rework DIG modesetting on DCE3+
drm/radeon: don't disable plls that are in use by other crtcs
drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
drm/radeon: initialize tracked CS state
drm/radeon: fix reading CB_COLORn_MASK from the CS
drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
drm/i915: Use the correct size of the GTT for placing the per-process entries
drm: Check for invalid cursor flags
drm: Initialize object type when using DRM_MODE() macro
drm/i915: fix color order for BGR formats on IVB
drm/i915: fix wrong order of parameters in port checking functions
Heiko Carstens [Tue, 28 Aug 2012 08:02:08 +0000 (10:02 +0200)]
s390/32: Don't clobber personality flags on exec
In native 32 bit mode the personality flags were not correctly inherited.
This is the s390 version of 59e4c3a2 "powerpc/32: Don't clobber personality
flags on exec".
Reported-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Mark Asselstine [Wed, 8 Aug 2012 17:14:36 +0000 (13:14 -0400)]
firmware: fix directory creation rule matching with make 3.82
Attempting to run 'firmware_install' with CONFIG_USB_SERIAL_TI=y when
using make 3.82 results in an error
make[2]: *** No rule to make target `/lib/firmware/./', needed by
`/lib/firmware/ti_3410.fw'. Stop.
It turns out make 3.82 is picky when matching directory names with
trailing slashes as a result, where make 3.81 would handle this
correctly make 3.82 does not find the rule needed to create the
directory.
The './' seen in the error is added by $(dir) for firmware which
resides in the base firmware src directory, such as
ti_3410.fw.ihex. By performing $(dir) after we prepend the
$(INSTALL_FW_PATH) we can ensure we don't end up with a './' in the
middle of the path and the directory will be properly created.
This change works with make 3.81 and should work with previous
versions as well.
Signed-off-by: Mark Asselstine <mark.asselstine@windriver.com> Signed-off-by: Michal Marek <mmarek@suse.cz>
Daniel Mack [Wed, 29 Aug 2012 11:17:05 +0000 (13:17 +0200)]
ALSA: snd-usb: Fix URB cancellation at stream start
Commit e9ba389c5 ("ALSA: usb-audio: Fix scheduling-while-atomic bug in
PCM capture stream") fixed a scheduling-while-atomic bug that happened
when snd_usb_endpoint_start was called from the trigger callback, which
is an atmic context. However, the patch breaks the idea of the endpoints
reference counting, which is the reason why the driver has been
refactored lately.
Revert that commit and let snd_usb_endpoint_start() take care of the URB
cancellation again. As this function is called from both atomic and
non-atomic context, add a flag to denote whether the function may sleep.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Cc: <dri-devel@lists.freedesktop.org> Cc: Adam Jackson <ajax@redhat.com> Cc: Ian Pilcher <arequipeno@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 30 Aug 2012 00:35:34 +0000 (10:35 +1000)]
Merge branch 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Alex writes:
Highlights:
- fix a gart regression on older IGP chips
- more MSAA fixes
- fix a double free in gpu reset code
- modesetting fixes
- trinity dig encoder fix.
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix dig encoder selection on DCE61
drm/radeon: fix double free in radeon_gpu_reset
drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
drm/radeon: rework panel mode setup
drm/radeon/atom: powergating fixes for DCE6
drm/radeon/atom: rework DIG modesetting on DCE3+
drm/radeon: don't disable plls that are in use by other crtcs
drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
drm/radeon: initialize tracked CS state
drm/radeon: fix reading CB_COLORn_MASK from the CS
Forest Bond [Mon, 13 Aug 2012 16:31:24 +0000 (16:31 +0000)]
gma500: Consider CRTC initially active.
[this one ideally should make 3.6 - it fixes the very annoying mode setting bug]
This causes the pipe to be forced off prior to initial mode set, which
roughly mirrors the behavior of the i915 driver. It fixes initial mode
setting on my Intel DN2800MT (Cedarview) board. Without it, mode
setting triggers an out-of-range error from the monitor for most modes,
but only on initial configuration (i.e. they can be configured
successfully from userspace after that).
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch reverts the offending commit and fixes be_poll() by
avoid disabling BH there, this is okay because be_poll()
can be called either by poll_napi() which already disables
IRQ, or by net_rx_action() which already disables BH.
Reported-by: Andrew Morton <akpm@linux-foundation.org> Reported-by: Sylvain Munaut <s.munaut@whatever-company.com> Cc: Sylvain Munaut <s.munaut@whatever-company.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: David Miller <davem@davemloft.net> Cc: Sathya Perla <sathya.perla@emulex.com> Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com> Cc: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: Cong Wang <amwang@redhat.com> Tested-by: Sylvain Munaut <s.munaut@whatever-company.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 29 Aug 2012 18:36:22 +0000 (11:36 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"I've split out the big send/receive update from my last pull request
and now have just the fixes in my for-linus branch. The send/recv
branch will wander over to linux-next shortly though.
The largest patches in this pull are Josef's patches to fix DIO
locking problems and his patch to fix a crash during balance. They
are both well tested.
The rest are smaller fixes that we've had queued. The last rc came
out while I was hacking new and exciting ways to recover from a
misplaced rm -rf on my dev box, so these missed rc3."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (25 commits)
Btrfs: fix that repair code is spuriously executed for transid failures
Btrfs: fix ordered extent leak when failing to start a transaction
Btrfs: fix a dio write regression
Btrfs: fix deadlock with freeze and sync V2
Btrfs: revert checksum error statistic which can cause a BUG()
Btrfs: remove superblock writing after fatal error
Btrfs: allow delayed refs to be merged
Btrfs: fix enospc problems when deleting a subvol
Btrfs: fix wrong mtime and ctime when creating snapshots
Btrfs: fix race in run_clustered_refs
Btrfs: don't run __tree_mod_log_free_eb on leaves
Btrfs: increase the size of the free space cache
Btrfs: barrier before waitqueue_active
Btrfs: fix deadlock in wait_for_more_refs
btrfs: fix second lock in btrfs_delete_delayed_items()
Btrfs: don't allocate a seperate csums array for direct reads
Btrfs: do not strdup non existent strings
Btrfs: do not use missing devices when showing devname
Btrfs: fix that error value is changed by mistake
Btrfs: lock extents as we map them in DIO
...
David Rientjes [Wed, 29 Aug 2012 02:57:21 +0000 (19:57 -0700)]
mm, slab: lock the correct nodelist after reenabling irqs
cache_grow() can reenable irqs so the cpu (and node) can change, so ensure
that we take list_lock on the correct nodelist.
This fixes an issue with commit 072bb0aa5e06 ("mm: sl[au]b: add
knowledge of PFMEMALLOC reserve pages") where list_lock for the wrong
node was taken after growing the cache.
Reported-and-tested-by: Haggai Eran <haggaie@mellanox.com> Signed-off-by: David Rientjes <rientjes@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christian König [Wed, 29 Aug 2012 11:24:15 +0000 (13:24 +0200)]
drm/radeon: fix double free in radeon_gpu_reset
radeon_ring_restore is freeing the memory for the saved
ring data. We need to remember that, otherwise we try to
restore the ring data again on the next try. Additional
to that it shouldn't try the reset infinitely if we have
saved ring data.
Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Jerome Glisse [Tue, 28 Aug 2012 20:50:22 +0000 (16:50 -0400)]
drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
It seems some of those IGP dislike non dma32 page despite what
documentation says. Fix regression since we allowed non dma32
pages. It seems it only affect some revision of those IGP chips
as we don't know which one just force dma32 for all of them.
Alex Deucher [Mon, 27 Aug 2012 21:48:18 +0000 (17:48 -0400)]
drm/radeon: rework panel mode setup
Adjust the panel mode setup to match the behavior
of the vbios. Rather than checking for specific
bridge chip ids, just check the eDP configuration register.
This saves extra aux transactions and works across
DP bridge chips without requiring additional per chip
id checking.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Fri, 24 Aug 2012 22:21:21 +0000 (18:21 -0400)]
drm/radeon/atom: powergating fixes for DCE6
Power gating is per crtc pair, but the powergating registers
should be called individually. The hw handles power up/down
properly. The pair is powered up if either crtc in the pair
is powered up and the pair is not powered down until both
crtcs in the pair are powered down. This simplifies
programming and should save additional power as the previous
code never actually power gated the crtc pair.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Alex Deucher [Wed, 22 Aug 2012 13:54:56 +0000 (09:54 -0400)]
drm/radeon/atom: rework DIG modesetting on DCE3+
The ordering is important and the current drm code
wasn't cutting it for modern DIG encoders. We need
to have information about crtc before setting up
the encoders so I've shifted the ordering a bit.
Probably we'll need a full rework akin to danvet's
recent intel patchs. This patch fixes numerous
issues with DP bridge chips and makes link training
much more reliable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Marek Olšák [Fri, 24 Aug 2012 12:27:36 +0000 (14:27 +0200)]
drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
Checking of the second colorbuffer was skipped on r700, because
CB_TARGET_MASK was 0xf. With r600, CB_TARGET_MASK is changed to 0xff,
so we must set the number of samples of the second colorbuffer to 1 in order
to pass the CS checker.
The DRM version is bumped, because RESOLVE_BOX is always rejected without this
fix on r600.
Signed-off-by: Marek Olšák <maraeo@gmail.com> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dave Airlie [Wed, 29 Aug 2012 10:09:23 +0000 (20:09 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel writes:
"Just a few smaller things:
- Fix up a pipe vs. plane confusion from a refactoring, fixes a regression
from 3.1 (Anhua Xu).
- Fix ivb sprite pixel formats (Vijay).
- Fixup ppgtt pde placement for machines where the Bios artifically limits
the availbale gtt space in the name of ... product differentiation
(Chris). This fixes an oops.
- Yet another no_lvds quirk entry."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
drm/i915: Use the correct size of the GTT for placing the per-process entries
drm/i915: fix color order for BGR formats on IVB
drm/i915: fix wrong order of parameters in port checking functions
Ben Skeggs [Mon, 27 Aug 2012 06:22:49 +0000 (16:22 +1000)]
drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
On some Fermi chipsets (NVCE particularly) PCOPY1 doesn't exist. And if
what I've seen on Kepler is true of Fermi too, chipsets of the same type
can have different PCOPY units available.
This should fix a v3.5 regression reported by a number of people effecting
suspend/resume on NVC8/NVCE chipsets.
Cc: stable@vger.kernel.org [3.5] Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Stefan Behrens [Fri, 10 Aug 2012 14:58:21 +0000 (08:58 -0600)]
Btrfs: fix that repair code is spuriously executed for transid failures
If verify_parent_transid() fails for all mirrors, the current code
calls repair_io_failure() anyway which means:
- that the disk block is rewritten without repairing anything and
- that a kernel log message is printed which misleadingly claims
that a read error was corrected.
This is an example:
parent transid verify failed on 615015833600 wanted 110423 found 110424
parent transid verify failed on 615015833600 wanted 110423 found 110424
btrfs read error corrected: ino 1 off 615015833600 (dev /dev/...)
It is wrong to ignore the results from verify_parent_transid() and to
call repair_eb_io_failure() when the verification of the transids failed.
This commit fixes the issue.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de> Signed-off-by: Chris Mason <chris.mason@oracle.com>
In dio write, we should unlock the section which we didn't do IO on in case that
we fall back to buffered write. But we need to not only unlock the section
but also cleanup reserved space for the section.
This bug was found while running xfstests 133, with this 133 no longer complains.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef Bacik [Fri, 24 Aug 2012 18:53:03 +0000 (12:53 -0600)]
Btrfs: fix deadlock with freeze and sync V2
We can deadlock with freeze right now because we unconditionally start a
transaction in our ->sync_fs() call. To fix this just check and see if we
have a running transaction to commit. This saves us from the deadlock
because at this point we'll have the umount sem for the sb so we're safe
from freezes coming in after we've done our check. With this patch the
freeze xfstests no longer deadlocks. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Stefan Behrens [Mon, 27 Aug 2012 14:30:03 +0000 (08:30 -0600)]
Btrfs: revert checksum error statistic which can cause a BUG()
Commit 442a4f6308e694e0fa6025708bd5e4e424bbf51c added btrfs device
statistic counters for detected IO and checksum errors to Linux 3.5.
The statistic part that counts checksum errors in
end_bio_extent_readpage() can cause a BUG() in a subfunction:
"kernel BUG at fs/btrfs/volumes.c:3762!"
That part is reverted with the current patch.
However, the counting of checksum errors in the scrub context remains
active, and the counting of detected IO errors (read, write or flush
errors) in all contexts remains active.
Cc: stable <stable@vger.kernel.org> # 3.5 Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Stefan Behrens [Wed, 1 Aug 2012 11:45:52 +0000 (05:45 -0600)]
Btrfs: remove superblock writing after fatal error
With commit acce952b0, btrfs was changed to flag the filesystem with
BTRFS_SUPER_FLAG_ERROR and switch to read-only mode after a fatal
error happened like a write I/O errors of all mirrors.
In such situations, on unmount, the superblock is written in
btrfs_error_commit_super(). This is done with the intention to be able
to evaluate the error flag on the next mount. A warning is printed
in this case during the next mount and the log tree is ignored.
The issue is that it is possible that the superblock points to a root
that was not written (due to write I/O errors).
The result is that the filesystem cannot be mounted. btrfsck also does
not start and all the other btrfs-progs tools fail to start as well.
However, mount -o recovery is working well and does the right things
to recover the filesystem (i.e., don't use the log root, clear the
free space cache and use the next mountable root that is stored in the
root backup array).
This patch removes the writing of the superblock when
BTRFS_SUPER_FLAG_ERROR is set, and removes the handling of the error
flag in the mount function.
These lines can be used to reproduce the issue (using /dev/sdm):
SCRATCH_DEV=/dev/sdm
SCRATCH_MNT=/mnt
echo 0 25165824 linear $SCRATCH_DEV 0 | dmsetup create foo
ls -alLF /dev/mapper/foo
mkfs.btrfs /dev/mapper/foo
mount /dev/mapper/foo $SCRATCH_MNT
echo bar > $SCRATCH_MNT/foo
sync
echo 0 25165824 error | dmsetup reload foo
dmsetup resume foo
ls -alF $SCRATCH_MNT
touch $SCRATCH_MNT/1
ls -alF $SCRATCH_MNT
sleep 35
echo 0 25165824 linear $SCRATCH_DEV 0 | dmsetup reload foo
dmsetup resume foo
sleep 1
umount $SCRATCH_MNT
btrfsck /dev/mapper/foo
dmsetup remove foo
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de> Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Josef Bacik [Tue, 7 Aug 2012 20:00:32 +0000 (16:00 -0400)]
Btrfs: allow delayed refs to be merged
Daniel Blueman reported a bug with fio+balance on a ramdisk setup.
Basically what happens is the balance relocates a tree block which will drop
the implicit refs for all of its children and adds a full backref. Once the
block is relocated we have to add the implicit refs back, so when we cow the
block again we add the implicit refs for its children back. The problem
comes when the original drop ref doesn't get run before we add the implicit
refs back. The delayed ref stuff will specifically prefer ADD operations
over DROP to keep us from freeing up an extent that will have references to
it, so we try to add the implicit ref before it is actually removed and we
panic. This worked fine before because the add would have just canceled the
drop out and we would have been fine. But the backref walking work needs to
be able to freeze the delayed ref stuff in time so we have this ever
increasing sequence number that gets attached to all new delayed ref updates
which makes us not merge refs and we run into this issue.
So to fix this we need to merge delayed refs. So everytime we run a
clustered ref we need to try and merge all of its delayed refs. The backref
walking stuff locks the delayed ref head before processing, so if we have it
locked we are safe to merge any refs inside of the sequence number. If
there is no sequence number we can merge all refs. Doing this not only
fixes our bug but keeps the delayed ref code from adding and removing
useless refs and batching together multiple refs into one search instead of
one search per delayed ref, which will really help our commit times. I ran
this with Daniels test and 276 and I haven't seen any problems. Thanks,
Reported-by: Daniel J Blueman <daniel@quora.org> Signed-off-by: Josef Bacik <jbacik@fusionio.com>
projects / karo-tx-linux.git / log