Linus Torvalds [Fri, 28 Aug 2015 00:46:06 +0000 (17:46 -0700)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull nvdimm fixlet from Dan Williams:
"This is a libnvdimm ABI fixup.
I pushed back on this change quite hard given the late date, that it
appears to be purely cosmetic, sysfs is not necessarily meant to be a
user friendly UI, and the kernel interprets the reversed polarity of
the ACPI_NFIT_MEM_ARMED flag correctly. When this flag is set, the
energy source of an NVDIMM is not armed and any new writes to the DIMM
may not be preserved.
However, Bob Moore warned me that it is important to get these things
named correctly wherever they appear otherwise we run the risk of a
less than cautious firmware engineer implementing the polarity the
wrong way. Once a mistake like that escapes into production platforms
the flag becomes useless and we need to move to a new bit position.
Bob has agreed to take a change through ACPICA to rename
ACPI_NFIT_MEM_ARMED to ACPI_NFIT_MEM_NOT_ARMED, and the patch below
from Toshi brings the sysfs representation of these flags in line with
their respective polarities.
Please pull for 4.2 as this is the first kernel to expose the ACPI
NFIT sysfs representation, and this is likely a kernel that firmware
developers will be using for checking out their NVDIMM enabling"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: Clarify memory device state flags strings
Toshi Kani [Wed, 26 Aug 2015 16:20:23 +0000 (10:20 -0600)]
nfit: Clarify memory device state flags strings
ACPI 6.0 NFIT Memory Device State Flags in Table 5-129 defines
NVDIMM status as follows. These bits indicate multiple info,
such as failures, pending event, and capability.
Bit [0] set to 1 to indicate that the previous SAVE to the
Memory Device failed.
Bit [1] set to 1 to indicate that the last RESTORE from the
Memory Device failed.
Bit [2] set to 1 to indicate that platform flush of data to
Memory Device failed. As a result, the restored data content
may be inconsistent even if SAVE and RESTORE do not indicate
failure.
Bit [3] set to 1 to indicate that the Memory Device is observed
to be not armed prior to OSPM hand off. A Memory Device is
considered armed if it is able to accept persistent writes.
Bit [4] set to 1 to indicate that the Memory Device observed
SMART and health events prior to OSPM handoff.
/sys/bus/nd/devices/nmemX/nfit/flags shows this flags info.
The output strings associated with the bits are "save", "restore",
"smart", etc., which can be confusing as they may be interpreted
as positive status, i.e. save succeeded.
Change also the dev_info() message in acpi_nfit_register_dimms()
to be consistent with the sysfs flags strings.
Reported-by: Robert Elliott <elliott@hp.com> Signed-off-by: Toshi Kani <toshi.kani@hp.com>
[ross: rename 'not_arm' to 'not_armed'] Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
[djbw: defer adding bit5, HEALTH_ENABLED, for now] Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Linus Torvalds [Thu, 27 Aug 2015 18:12:41 +0000 (11:12 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull amr64 kvm fix from Will Deacon:
"We've uncovered a nasty bug in the arm64 KVM code which allows a badly
behaved 32-bit guest to bring down the host. The fix is simple (it's
what I believe we call a "brown paper bag" bug) and I don't think it
makes sense to sit on this, particularly as Russell ended up
triggering this rather than just somebody noticing a potential problem
by inspection.
Usually arm64 KVM changes would go via Paolo's tree, but he's on
holiday at the moment and the deal is that anything urgent gets
shuffled via the arch trees, so here it is.
Summary:
Fix arm64 KVM issue when injecting an abort into a 32-bit guest, which
would lead to an illegal exception return at EL2 and a subsequent host
crash"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: KVM: Fix host crash when injecting a fault into a 32bit guest
Marc Zyngier [Thu, 27 Aug 2015 15:10:01 +0000 (16:10 +0100)]
arm64: KVM: Fix host crash when injecting a fault into a 32bit guest
When injecting a fault into a misbehaving 32bit guest, it seems
rather idiotic to also inject a 64bit fault that is only going
to corrupt the guest state. This leads to a situation where we
perform an illegal exception return at EL2 causing the host
to crash instead of killing the guest.
Just fix the stupid bug that has been there from day 1.
Cc: <stable@vger.kernel.org> Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Linus Torvalds [Wed, 26 Aug 2015 18:08:47 +0000 (11:08 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Two fixes in this pull request:
- The writeback regression fix from Tejun, which has been weeks in
the making. This fixes a case where we would sometimes not issue
writeback when we should have.
- An older fix for a memory corruption issue in mtip32xx. It was
deferred since we wanted a better fix for this (driver should not
have to handle that case), but given the timing, it's better to put
the simple fix in for 4.2 release"
* 'for-linus' of git://git.kernel.dk/linux-block:
mtip32x: fix regression introduced by blk-mq per-hctx flush
writeback: sync_inodes_sb() must write out I_DIRTY_TIME inodes and always call wait_sb_inodes()
Linus Torvalds [Wed, 26 Aug 2015 00:26:00 +0000 (17:26 -0700)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull nvdimm fix from Dan Williams:
"A single fix for status register read size in the nd_blk driver.
The effect of getting the width of this register read wrong is that
all I/O fails when the read returns non-zero. Given the availability
of ACPI 6 NFIT enabled platforms, this could reasonably wait to come
in during the 4.3 merge window with a tag for 4.2-stable. Otherwise,
this makes the 4.2 kernel fully functional with devices that conform
to the mmio-block-apertures defined in the ACPI 6 NFIT (NVDIMM
Firmware Interface Table)"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit, nd_blk: BLK status register is only 32 bits
Jan Beulich [Mon, 24 Aug 2015 12:22:25 +0000 (06:22 -0600)]
LSM: restore certain default error codes
While in most cases commit b1d9e6b064 ("LSM: Switch to lists of hooks")
retained previous error returns, in three cases it altered them without
any explanation in the commit message. Restore all of them - in the
security_old_inode_init_security() case this led to reiserfs using
uninitialized data, sooner or later crashing the system (the only other
user of this function - ocfs2 - was unaffected afaict, since it passes
pre-initialized structures).
Signed-off-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Reported-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com> Tested-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com> Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jeff Moyer [Wed, 29 Jul 2015 14:22:50 +0000 (10:22 -0400)]
mtip32x: fix regression introduced by blk-mq per-hctx flush
Hi,
After commit f70ced091707 (blk-mq: support per-distpatch_queue flush
machinery), the mtip32xx driver may oops upon module load due to walking
off the end of an array in mtip_init_cmd. On initialization of the
flush_rq, init_request is called with request_index >= the maximum queue
depth the driver supports. For mtip32xx, this value is used to index
into an array. What this means is that the driver will walk off the end
of the array, and either oops or cause random memory corruption.
The problem is easily reproduced by doing modprobe/rmmod of the mtip32xx
driver in a loop. I can typically reproduce the problem in about 30
seconds.
Now, in the case of mtip32xx, it actually doesn't support flush/fua, so
I think we can simply return without doing anything. In addition, no
other mq-enabled driver does anything with the request_index passed into
init_request(), so no other driver is affected. However, I'm not really
sure what is expected of drivers. Ming, what did you envision drivers
would do when initializing the flush requests?
Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Tejun Heo [Tue, 25 Aug 2015 18:11:52 +0000 (14:11 -0400)]
writeback: sync_inodes_sb() must write out I_DIRTY_TIME inodes and always call wait_sb_inodes()
e79729123f63 ("writeback: don't issue wb_writeback_work if clean")
updated writeback path to avoid kicking writeback work items if there
are no inodes to be written out; unfortunately, the avoidance logic
was too aggressive and broke sync_inodes_sb().
* sync_inodes_sb() must write out I_DIRTY_TIME inodes but I_DIRTY_TIME
inodes dont't contribute to bdi/wb_has_dirty_io() tests and were
being skipped over.
* inodes are taken off wb->b_dirty/io/more_io lists after writeback
starts on them. sync_inodes_sb() skipping wait_sb_inodes() when
bdi_has_dirty_io() breaks it by making it return while writebacks
are in-flight.
This patch fixes the breakages by
* Removing bdi_has_dirty_io() shortcut from bdi_split_work_to_wbs().
The callers are already testing the condition.
* Removing bdi_has_dirty_io() shortcut from sync_inodes_sb() so that
it always calls into bdi_split_work_to_wbs() and wait_sb_inodes().
* Making bdi_split_work_to_wbs() consider the b_dirty_time list for
WB_SYNC_ALL writebacks.
Kudos to Eryu, Dave and Jan for tracking down the issue.
Signed-off-by: Tejun Heo <tj@kernel.org> Fixes: e79729123f63 ("writeback: don't issue wb_writeback_work if clean") Link: http://lkml.kernel.org/g/20150812101204.GE17933@dhcp-13-216.nay.redhat.com Reported-and-bisected-by: Eryu Guan <eguan@redhat.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Jan Kara <jack@suse.com> Cc: Ted Ts'o <tytso@google.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Linus Torvalds [Tue, 25 Aug 2015 16:01:05 +0000 (09:01 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Thomas Gleixner:
"A single fix for a APIC regression introduced in 4.0 which went
undetected until now.
I screwed up the x2apic cleanup in a subtle way. The screwup is only
visible on systems which have x2apic preenabled in the BIOS and need
to disable it during boot"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Fix fallout from x2apic cleanup
J. Bruce Fields [Mon, 24 Aug 2015 20:44:40 +0000 (16:44 -0400)]
nfsd: Add Jeff Layton as co-maintainer
Jeff has been doing a lot of development (including much of the
state-locking rewrite just as one example) plus lots of review and other
miscellaneous nfsd work, so let's acknowledge the status quo.
I'll continue to be the one to send regular pull requests but Jeff will
should be available to cover there occasionally too.
Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 24 Aug 2015 03:46:22 +0000 (20:46 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A couple of major (hang and deadlock) fixes with fortunately fairly
rare triggering conditions. The PM oops is only really triggered by
people using enclosure services (rare) and the fnic driver is mostly
used in enterprise environments"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
SCSI: Fix NULL pointer dereference in runtime PM
fnic: Use the local variable instead of I/O flag to acquire io_req_lock in fnic_queuecommand() to avoid deadloack
Linus Torvalds [Sun, 23 Aug 2015 14:23:09 +0000 (07:23 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS bug fixes from Ralf Baechle:
"Two more fixes for 4.2.
One fixes a build issue with the LLVM assembler - LLVM assembler macro
names are case sensitive, GNU as macro names are insensitive; the
other corrects a license string (GPL v2, not GPLv2) such that the
module loader will recognice the license correctly"
Vincent Bernat [Sat, 15 Aug 2015 13:49:13 +0000 (15:49 +0200)]
9p: ensure err is initialized to 0 in p9_client_read/write
Some use of those functions were providing unitialized values to those
functions. Notably, when reading 0 bytes from an empty file on a 9P
filesystem, the return code of read() was not 0.
Linus Torvalds [Sat, 22 Aug 2015 22:48:04 +0000 (15:48 -0700)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Another couple of small ARM fixes.
A patch from Masahiro Yamada who noticed that "make -jN all zImage"
would end up generating bad images where N > 1, and a patch from
Nicolas to fix the Marvell CPU user access optimisation code when page
faults are disabled"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8418/1: add boot image dependencies to not generate invalid images
ARM: 8414/1: __copy_to_user_memcpy: fix mmap semaphore usage
Linus Torvalds [Sat, 22 Aug 2015 15:15:36 +0000 (08:15 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Various low level fixes: fix more fallout from the FPU rework and the
asm entry code rework, plus an MSI rework fix, and an idle-tracing fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu/math-emu: Fix crash in fork()
x86/fpu/math-emu: Fix math-emu boot crash
x86/idle: Restore trace_cpu_idle to mwait_idle() calls
x86/irq: Build correct vector mapping for multiple MSI interrupts
Revert "sched/x86_64: Don't save flags on context switch"
Linus Torvalds [Sat, 22 Aug 2015 15:06:28 +0000 (08:06 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Tooling fixes: a 'perf record' deadlock fix plus debuggability fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf top: Show backtrace when handling a SIGSEGV on --stdio mode
perf tools: Fix buildid processing
perf tools: Make fork event processing more resilient
perf tools: Avoid deadlock when map_groups are broken
Thomas Gleixner [Sat, 22 Aug 2015 14:41:17 +0000 (16:41 +0200)]
x86/apic: Fix fallout from x2apic cleanup
In the recent x2apic cleanup I got two things really wrong:
1) The safety check in __disable_x2apic which allows the function to
be called unconditionally is backwards. The check is there to
prevent access to the apic MSR in case that the machine has no
apic. Though right now it returns if the machine has an apic and
therefor the disabling of x2apic is never invoked.
2) x2apic_disable() sets x2apic_mode to 0 after registering the local
apic. That's wrong, because register_lapic_address() checks x2apic
mode and therefor takes the wrong code path.
This results in boot failures on machines with x2apic preenabled by
BIOS and can also lead to an fatal MSR access on machines without
apic.
The solutions are simple:
1) Correct the sanity check for apic availability
2) Clear x2apic_mode _before_ calling register_lapic_address()
Fixes: 659006bf3ae3 'x86/x2apic: Split enable and setup function' Reported-and-tested-by: Javier Monteagudo <javiermon@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://bugzilla.redhat.com/show_bug.cgi?id=1224764 Cc: stable@vger.kernel.org # 4.0+ Cc: Laura Abbott <labbott@redhat.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Joerg Roedel <joro@8bytes.org> Cc: Tony Luck <tony.luck@intel.com> Cc: Borislav Petkov <bp@alien8.de>
Linus Torvalds [Sat, 22 Aug 2015 14:45:36 +0000 (07:45 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A series of small fixlets for a regression visible on OMAP devices
caused by the conversion of the OMAP interrupt chips to hierarchical
interrupt domains. Mostly one liners on the driver side plus a small
helper function in the core to avoid open coded mess in the drivers"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/crossbar: Restore set_wake functionality
irqchip/crossbar: Restore the mask on suspend behaviour
ARM: OMAP: wakeupgen: Restore the irq_set_type() mechanism
irqchip/crossbar: Restore the irq_set_type() mechanism
genirq: Introduce irq_chip_set_type_parent() helper
genirq: Don't return ENOSYS in irq_chip_retrigger_hierarchy
Linus Torvalds [Sat, 22 Aug 2015 14:37:41 +0000 (07:37 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two minimalistic fixes for 4.2 regressions:
- Eric fixed a thinko in the timer_list base switching code caused by
the overhaul of the timer wheel. It can cause a cpu to see the
wrong base for a timer while we move the timer around.
- Guenter fixed a regression for IMX if booted w/o device tree, where
the timer interrupt is not initialized and therefor the machine
fails to boot"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/imx: Fix boot with non-DT systems
timer: Write timer->flags atomically
b1276c48e91b ("x86/fpu: Initialize fpregs in fpu__init_cpu_generic()")
I failed to consider math-emu's limitation that it cannot execute the
FNINIT instruction in kernel mode.
The long term fix might be to allow math-emu to execute (certain) kernel
mode FPU instructions, but for now apply the safe (albeit somewhat ugly)
fix: initialize the emulation state explicitly without trapping out to
the FPU emulator.
Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
While the idea behind get_maintainer seems highly useful it's
unfortunately way to trigger happy to grab people that once had a few
commits to files. For someone like me who does a lot of tree-wide API
work that leads to an incredible amount of Cc spam.
Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: Joe Perches <joe@perches.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 21 Aug 2015 21:11:51 +0000 (14:11 -0700)]
mm: make page pfmemalloc check more robust
Commit c48a11c7ad26 ("netvm: propagate page->pfmemalloc to skb") added
checks for page->pfmemalloc to __skb_fill_page_desc():
if (page->pfmemalloc && !page->mapping)
skb->pfmemalloc = true;
It assumes page->mapping == NULL implies that page->pfmemalloc can be
trusted. However, __delete_from_page_cache() can set set page->mapping
to NULL and leave page->index value alone. Due to being in union, a
non-zero page->index will be interpreted as true page->pfmemalloc.
So the assumption is invalid if the networking code can see such a page.
And it seems it can. We have encountered this with a NFS over loopback
setup when such a page is attached to a new skbuf. There is no copying
going on in this case so the page confuses __skb_fill_page_desc which
interprets the index as pfmemalloc flag and the network stack drops
packets that have been allocated using the reserves unless they are to
be queued on sockets handling the swapping which is the case here and
that leads to hangs when the nfs client waits for a response from the
server which has been dropped and thus never arrive.
The struct page is already heavily packed so rather than finding another
hole to put it in, let's do a trick instead. We can reuse the index
again but define it to an impossible value (-1UL). This is the page
index so it should never see the value that large. Replace all direct
users of page->pfmemalloc by page_is_pfmemalloc which will hide this
nastiness from unspoiled eyes.
The information will get lost if somebody wants to use page->index
obviously but that was the case before and the original code expected
that the information should be persisted somewhere else if that is
really needed (e.g. what SLAB and SLUB do).
[akpm@linux-foundation.org: fix blooper in slub] Fixes: c48a11c7ad26 ("netvm: propagate page->pfmemalloc to skb") Signed-off-by: Michal Hocko <mhocko@suse.com> Debugged-by: Vlastimil Babka <vbabka@suse.com> Debugged-by: Jiri Bohac <jbohac@suse.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: David Miller <davem@davemloft.net> Acked-by: Mel Gorman <mgorman@suse.de> Cc: <stable@vger.kernel.org> [3.6+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 21 Aug 2015 18:18:10 +0000 (11:18 -0700)]
Merge tag 'pci-v4.2-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for ASPM-related NULL pointer dereference crashes on
Sparc and PowerPC and 64-bit PCI address-related HPMC crashes on
PA-RISC. These are both caused by things we merged in the v4.2 merge
window. Details:
Resource management
- Don't use 64-bit bus addresses on PA-RISC
Miscellaneous
- Tolerate hierarchies with no Root Port"
* tag 'pci-v4.2-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Don't use 64-bit bus addresses on PA-RISC
PCI: Tolerate hierarchies with no Root Port
Linus Torvalds [Fri, 21 Aug 2015 17:46:56 +0000 (10:46 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A bunch of i915 fixes, one revert a VBT fix that was a bit premature,
and some braswell feature removal that the hw actually didn't support.
One radeon race fix at boot, and one hlcdc build fix, one fix from
Russell that fixes build as well with new audio features.
This is hopefully all I have until -next"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: fix hotplug race at startup
drm/edid: add function to help find SADs
drm/i915: Avoid TP3 on CHV
drm/i915: remove HBR2 from chv supported list
Revert "drm/i915: Add eDP intermediate frequencies for CHV"
Revert "drm/i915: Allow parsing of variable size child device entries from VBT"
drm/atmel-hlcdc: Compile suspend/resume for PM_SLEEP only
drm/i915: Flag the execlists context object as dirty after every use
Dave Airlie [Fri, 21 Aug 2015 00:44:03 +0000 (10:44 +1000)]
Merge tag 'drm-intel-fixes-2015-08-20' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Revert of a VBT parsing commit that should've been queued for drm-next,
not v4.2. The revert unbreaks Braswell among other things.
Also on Braswell removal of DP HBR2/TP3 and intermediate eDP frequency
support. The code was optimistically added based on incorrect
documentation; the platform does not support them. These are cc: stable.
Finally a gpu state fix from Chris, also cc: stable.
* tag 'drm-intel-fixes-2015-08-20' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Avoid TP3 on CHV
drm/i915: remove HBR2 from chv supported list
Revert "drm/i915: Add eDP intermediate frequencies for CHV"
Revert "drm/i915: Allow parsing of variable size child device entries from VBT"
drm/i915: Flag the execlists context object as dirty after every use
Linus Torvalds [Fri, 21 Aug 2015 00:06:11 +0000 (17:06 -0700)]
Merge tag 'pm+acpi-4.2-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix a recent regression in the ACPI backlight code and a memory
leak in the Exynos cpufreq driver.
Specifics:
- Fix a recently introduced issue in the ACPI backlight code which
causes lockdep to complain about a circular lock dependency during
initialization (Hans de Goede).
- Fix a possible memory during initialization in the Exynos cpufreq
driver (Shailendra Verma)"
* tag 'pm+acpi-4.2-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: exynos: Fix for memory leak in case SoC name does not match
ACPI / video: Fix circular lock dependency issue in the video-detect code
Bjorn Helgaas [Thu, 20 Aug 2015 05:08:15 +0000 (00:08 -0500)]
PCI: Don't use 64-bit bus addresses on PA-RISC
Meelis and Helge reported that 3a9ad0b4fdcd ("PCI: Add pci_bus_addr_t")
caused HPMCs on A500 and hangs on rp5470.
PA-RISC does not set ARCH_DMA_ADDR_T_64BIT, even for 64-bit kernels, so
prior to 3a9ad0b4fdcd, we always used 32-bit PCI addresses. After 3a9ad0b4fdcd, we do use 64-bit PCI addresses in 64-bit kernels, and
apparently there's some PA-RISC problem related to them.
Jisheng Zhang [Thu, 20 Aug 2015 04:54:39 +0000 (12:54 +0800)]
x86/idle: Restore trace_cpu_idle to mwait_idle() calls
Commit b253149b843f ("sched/idle/x86: Restore mwait_idle() to fix boot
hangs, to improve power savings and to improve performance") restores
mwait_idle(), but the trace_cpu_idle related calls are missing. This
causes powertop on my old desktop powered by Intel Core2 E6550 to
report zero wakeups and zero events.
Linus Torvalds [Thu, 20 Aug 2015 19:08:38 +0000 (12:08 -0700)]
Merge tag 'sound-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a small collecton of sound fix patches.
The most significant one is the disablement of newly introduced
topology API. Its ABI couldn't be stabilized enough, so we decided to
delay for 4.3 in the end. Other than that, all oneliner fixes: a
USB-audio runtime PM fix and a couple of HD-audio quirks"
* tag 'sound-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add dock support for Thinkpad W541 (17aa:2211)
ALSA: usb-audio: Fix runtime PM unbalance
ASoC: topology: Disable use from userspace
ASoC: topology: Add Kconfig option for topology
ALSA: hda - Fix the white noise on Dell laptop
Pull SCSI target fixes from Nicholas Bellinger:
"This contains a v4.2-rc specific RCU module unload regression bug-fix,
a long-standing iscsi-target bug-fix for duplicate target_xfer_tags
during NOP processing from Alexei, and two more small REPORT_LUNs
emulation related patches to make Solaris FC host LUN scanning happy
from Roland.
There is also one patch not included that allows target-core to limit
the number of fabric driver SGLs per I/O request using residuals, that
is currently required as a work-around for FC hosts which don't honor
EVPD block-limits settings. At this point, it will most likely become
for-next material"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix handling of small allocation lengths in REPORT LUNS
target: REPORT LUNS should return LUN 0 even for dynamic ACLs
target/iscsi: Fix double free of a TUR followed by a solicited NOPOUT
target: Perform RCU callback barrier before backend/fabric unload
Linus Torvalds [Thu, 20 Aug 2015 18:32:33 +0000 (11:32 -0700)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal fixes from Eduardo Valentin:
"Last minute fixes on the thermal-soc tree. There is a fix of a long
lasting bug in cpu cooling device, thanks for RMK for being pushing
this"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal/cpu_cooling: update policy limits if clipped_freq < policy->max
thermal/cpu_cooling: rename max_freq as clipped_freq in notifier
thermal/cpu_cooling: rename cpufreq_val as clipped_freq
thermal/cpu_cooling: convert 'switch' block to 'if' block in notifier
thermal/cpu_cooling: quit early after updating policy
thermal/cpu_cooling: No need to initialize max_freq to 0
thermal: cpu_cooling: fix lockdep problems in cpu_cooling
thermal: power_allocator: do not use devm* interfaces
Guenter Roeck [Thu, 20 Aug 2015 10:27:21 +0000 (03:27 -0700)]
clocksource/imx: Fix boot with non-DT systems
Commit 6dd747825b20 ("ARM: imx: move timer resources into a structure")
moved initialization parameters into a data structure, but neglected to set
the irq field in that data structure for non-DT boots. This causes the system
to hang if a non-DT boot is attempted.
Fixes: 6dd747825b20 ("ARM: imx: move timer resources into a structure") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Cc: Shawn Guo <shawn.guo@linaro.org> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Link: http://lkml.kernel.org/r/1440066441-13930-1-git-send-email-linux@roeck-us.net Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
David Vrabel [Thu, 20 Aug 2015 10:33:41 +0000 (11:33 +0100)]
x86/xen: make CONFIG_XEN depend on CONFIG_X86_LOCAL_APIC
Since commit feb44f1f7a4ac299d1ab1c3606860e70b9b89d69 (x86/xen:
Provide a "Xen PV" APIC driver to support >255 VCPUs) Xen guests need
a full APIC driver and thus should depend on X86_LOCAL_APIC.
This fixes an i386 build failure with !SMP && !CONFIG_X86_UP_APIC by
disabling Xen support in this configuration.
Users needing Xen support in a non-SMP i386 kernel will need to enable
CONFIG_X86_UP_APIC.
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Cc: <stable@vger.kernel.org>
Ingo Molnar [Thu, 20 Aug 2015 09:47:14 +0000 (11:47 +0200)]
Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Fix buildid processing done at the end of a 'perf record' session, a
problem that happened in workloads involving lots of small short-lived
processes. That code was not asking the perf_session layer to order
the events.
Make the code more robust to handle some of the problems with such
out-of-order events and fix 'perf record' to ask for ordered events
on systems where we have perf_event_attr.sample_id_all. (Adrian Hunter)
- Show backtrace when handling a SIGSEGV in 'perf top --stdio' (Arnaldo Carvalho de Melo)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
The TI crossbar irqchip doesn't provides any facility to configure the
wakeup sources, but the conversion to hierarchical irqdomains set the
irq_set_wake callback to irq_chip_set_wake_parent. The parent chip
(OMAP wakeupgen) has no irq_set_wake function either so the call will
fail with -ENOSYS. As a result the irq_set_wake() call in the resume
path will trigger an 'Unbalanced wake disable' warning.
Before the conversion the GIC irqchip was the top level irqchip and
correctly flagged with IRQCHIP_SKIP_SET_WAKE.
Restore the correct behaviour by removing the irq_set_type callback
from the crossbar irqchip and set the IRQCHIP_SKIP_SET_WAKE flag which
lets the irq_set_irq_wake() call from the driver succeed.
irqchip/crossbar: Restore the mask on suspend behaviour
The ARM GIC requires that all interrupts which are not used as a
wakeup source have to be masked during suspend.
The conversion of the crossbar irqchip to hierarchical irq domains
failed to mark the crossbar irqchip with the IRQCHIP_MASK_ON_SUSPEND
flag and therefor broke the suspend requirement of the GIC.
Before the conversion the flags were visible because the GIC was the
top level irqchip. After the conversion the crossbar irqchip is the
top level irq chip whose flags are evaluated in suspend_device_irq().
As the flag is not set the masking of the non-wakeup irqs is not
invoked which breaks suspend.
Add the IRQCHIP_MASK_ON_SUSPEND flag to the crossbar irqchip, so the
GIC interrupts get masked properly.
ARM: OMAP: wakeupgen: Restore the irq_set_type() mechanism
The conversion of the wakeupgen irqchip to hierarchical irq domains
failed to provide a mechanism to properly set the trigger type of an
interrupt.
The wakeupgen irq chip itself has no mechanism and therefor no
irq_set_type() callback. The code before the conversion relayed the
trigger configuration directly to the underlying GIC.
Restore the correct behaviour by setting the wakeupgen irq_set_type
callback to irq_chip_set_type_parent(). This propagates the
set_trigger() call to the underlying GIC irqchip.
irqchip/crossbar: Restore the irq_set_type() mechanism
The conversion of the crossbar irqchip to hierarchical irq domains
failed to provide a mechanism to properly set the trigger type of an
interrupt.
The crossbar irq chip itself has no mechanism and therefor no
irq_set_type() callback. The code before the conversion relayed the
trigger configuration directly to the underlying GIC.
Restore the correct behaviour by setting the crossbar irq_set_type
callback to irq_chip_set_type_parent(). This propagates the
set_trigger() call to the underlying GIC irqchip.
This helper is required for irq chips which do not implement a
irq_set_type callback and need to call down the irq domain hierarchy
for the actual trigger type change.
This helper is required to fix further wreckage caused by the
conversion of TI OMAP to hierarchical irq domains and therefor tagged
for stable.
genirq: Don't return ENOSYS in irq_chip_retrigger_hierarchy
irq_chip_retrigger_hierarchy() returns -ENOSYS if it was not able to
find at least one .irq_retrigger() callback implemented in the IRQ
domain hierarchy.
That's wrong, because check_irq_resend() expects a 0 return value from
the callback in case that the hardware assisted resend was not
possible. If the return value is non zero the core code assumes
hardware resend success and the software resend is not invoked.
This results in lost interrupts on platforms where none of the parent
irq chips in the hierarchy implements the retrigger callback.
This is observable on TI OMAP, where the hierarchy is:
ARM GIC <- OMAP wakeupgen <- TI Crossbar
Return 0 instead so the software resend mechanism gets invoked.
Yijing Wang [Mon, 17 Aug 2015 10:47:58 +0000 (18:47 +0800)]
PCI: Tolerate hierarchies with no Root Port
We should not assume any particular hardware topology. Commit d0751b98dfa3
("PCI: Add dev->has_secondary_link to track downstream PCIe links") relied
on the assumption that every PCIe hierarchy is rooted at a Root Port. But
we can't rely on any assumption about what hardware we will find; we just
have to deal with the world as it is.
On some platforms, PCIe devices (endpoints, switch upstream ports, etc.)
appear directly on the root bus, and there is no Root Port in the PCI bus
hierarchy. For example, Meelis observed these top-level devices on a
Sparc V245:
0000:02:00.0 PCI bridge to [bus 03-0d] Switch Upstream Port
0001:02:00.0 PCI bridge to [bus 03] PCIe to PCI/PCI-X Bridge
These devices *look* like they have links going upstream, but there really
are no upstream devices.
In set_pcie_port_type(), we used the parent device to figure out which side
of a switch port has a link, so if the parent device did not exist, we
dereferenced a NULL parent pointer.
Check whether the parent device exists before dereferencing it.
Meelis observed this oops on Sparc V245 and T2000. Ben Herrenschmidt says
this is also possible on IBM PowerVM guests on PowerPC.
[bhelgaas: changelog, comment] Link: http://lkml.kernel.org/r/alpine.LRH.2.20.1508122118210.18637@math.ut.ee Reported-by: Meelis Roos <mroos@linux.ee> Tested-by: Meelis Roos <mroos@linux.ee> Signed-off-by: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: David S. Miller <davem@davemloft.net>
Adrian Hunter [Wed, 19 Aug 2015 14:29:21 +0000 (17:29 +0300)]
perf tools: Fix buildid processing
After recording, 'perf record' post-processes the data to determine
which buildids are needed.
That processing must process the data in time order, if possible,
because otherwise dependent events, like forks and mmaps, will not make
sense.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Tested-by: Jiri Olsa <jolsa@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: http://lkml.kernel.org/r/1439994561-27436-4-git-send-email-adrian.hunter@intel.com
[ Moved the sample_id_add to after trying to open the events, use pr_warning ] Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adrian Hunter [Wed, 19 Aug 2015 14:29:20 +0000 (17:29 +0300)]
perf tools: Make fork event processing more resilient
When processing a fork event, the tools lookup the parent thread by its
tid. In a couple of cases, it is possible for that thread to have the
wrong pid.
That can happen if the data is being processed out of order, or if the
(fork) event that would have removed the erroneous thread was lost.
Assume the latter case, print a dump message, remove the erroneous
thread, create a new one with the correct pid, and keep going.
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Tested-by: Jiri Olsa <jolsa@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: http://lkml.kernel.org/r/1439994561-27436-3-git-send-email-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Takashi Iwai [Wed, 19 Aug 2015 16:31:54 +0000 (18:31 +0200)]
Merge tag 'asoc-v4.2-disable-topology' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Disable topology support for v4.2
The topology code merged in the v4.2 merge window introduced a new ABI
which was believed to be suitable for use but subsequently additional
work by the developers of this feature have revealed some problems that
need to be addressed. In order to allow this to be done without having
to support the initial ABI add Kconfig to disable the build and also add
some #error statements to the UAPI header so users can't use them.
Takashi Iwai [Wed, 19 Aug 2015 05:20:14 +0000 (07:20 +0200)]
ALSA: usb-audio: Fix runtime PM unbalance
The fix for deadlock in PM in commit [1ee23fe07ee8: ALSA: usb-audio:
Fix deadlocks at resuming] introduced a new check of in_pm flag.
However, the brainless patch author evaluated it in a wrong way
(logical AND instead of logical OR), thus usb_autopm_get_interface()
is wrongly called at probing, leading to unbalance of runtime PM
refcount.
This patch fixes it by correcting the logic.
Reported-by: Hans Yang <hansy@nvidia.com> Fixes: 1ee23fe07ee8 ('ALSA: usb-audio: Fix deadlocks at resuming') Cc: <stable@vger.kernel.org> [v3.15+] Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu> Acked-by: Antti Seppälä <a.seppala@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu> Acked-by: Antti Seppälä <a.seppala@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu> Acked-by: Antti Seppälä <a.seppala@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu> Acked-by: Antti Seppälä <a.seppala@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu> Acked-by: Antti Seppälä <a.seppala@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu> Acked-by: Antti Seppälä <a.seppala@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu> Acked-by: Antti Seppälä <a.seppala@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drm/i915: Allow parsing of variable size child device entries from VBT
That commit is not valid for v4.2, however it will be valid for v4.3. It
was simply queued too early.
The referenced regressing commit is just fine until the size of struct
common_child_dev_config changes, and that won't happen until
v4.3. Indeed, the expected size checks here rely on the increased size
of the struct, breaking new platforms.
Fixes: 047fe6e6db91 ("drm/i915: Allow parsing of variable size child device entries from VBT") Cc: Daniel Vetter <daniel@ffwll.ch> Cc: David Weinehall <david.weinehall@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Roland Dreier [Fri, 14 Aug 2015 04:59:19 +0000 (21:59 -0700)]
target: Fix handling of small allocation lengths in REPORT LUNS
REPORT LUNS should not fail just because the allocation length is less
than 16. The relevant section of SPC-4 is:
4.2.5.6 Allocation length
The ALLOCATION LENGTH field specifies the maximum number of bytes or
blocks that an application client has allocated in the Data-In
Buffer. The ALLOCATION LENGTH field specifies bytes unless a
different requirement is stated in the command definition.
An allocation length of zero specifies that no data shall be
transferred. This condition shall not be considered an error.
So we should just truncate our response rather than return an error.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Spencer Baugh <sbaugh@catern.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Sven Eckelmann [Tue, 18 Aug 2015 11:37:01 +0000 (13:37 +0200)]
batman-adv: Fix memory leak on tt add with invalid vlan
The object tt_local is allocated with kmalloc and not initialized when the
function batadv_tt_local_add checks for the vlan. But this function can
only cleanup the object when the (not yet initialized) reference counter of
the object is 1. This is unlikely and thus the object would leak when the
vlan could not be found.
Instead the uninitialized object tt_local has to be freed manually and the
pointer has to set to NULL to avoid calling the function which would try to
decrement the reference counter of the not existing object.
CID: 1316518 Fixes: 354136bcc3c4 ("batman-adv: fix kernel crash due to missing NULL checks") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 18 Aug 2015 19:17:36 +0000 (12:17 -0700)]
Merge tag 'dmaengine-fix-4.2-rc8' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fix from Vinod Koul:
"We recently found issue with dma_request_slave_channel() API causing
privatecnt value to go bad. This is fixed by balancing the privatecnt"
* tag 'dmaengine-fix-4.2-rc8' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: fix balance of privatecnt inc/dec operations
Mark Brown [Tue, 18 Aug 2015 05:59:25 +0000 (22:59 -0700)]
ASoC: topology: Disable use from userspace
Since the topology API is still in sufficient flux for changes to be
identified disable the use of the userspace ABI by adding #error
statements to the code, ensuring that nobody relies on the headers as
currently defined. It is expected that this change will be reverted for
v4.3.
Jiang Liu [Tue, 18 Aug 2015 15:20:20 +0000 (23:20 +0800)]
x86/irq: Build correct vector mapping for multiple MSI interrupts
Alex Deucher, Mark Rustad and Alexander Holler reported a regression
with the latest v4.2-rc4 kernel, which breaks some SATA controllers.
With multi-MSI capable SATA controllers, only the first port works,
all other ports time out when executing SATA commands.
This happens because the first argument to assign_irq_vector_policy()
is always the base linux irq number of the multi MSI interrupt block,
so all subsequent vector assignments operate on the base linux irq
number, so all MSI irqs are handled as the first irq number. Therefor
the other MSI irqs of a device are never set up correctly and never
fire.
Add the loop iterator to the base irq number so all vectors are
assigned correctly.
Fixes: b5dc8e6c21e7 "x86/irq: Use hierarchical irqdomain to manage CPU interrupt vectors" Reported-and-tested-by: Alex Deucher <alexdeucher@gmail.com> Reported-and-tested-by: Mark Rustad <mrustad@gmail.com> Reported-and-tested-by: Alexander Holler <holler@ahsoftware.de> Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Cc: Tony Luck <tony.luck@intel.com> Link: http://lkml.kernel.org/r/1439911228-9880-1-git-send-email-jiang.liu@linux.intel.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Alan Stern [Mon, 17 Aug 2015 15:02:42 +0000 (11:02 -0400)]
SCSI: Fix NULL pointer dereference in runtime PM
The routines in scsi_rpm.c assume that if a runtime-PM callback is
invoked for a SCSI device, it can only mean that the device's driver
has asked the block layer to handle the runtime power management (by
calling blk_pm_runtime_init(), which among other things sets q->dev).
However, this assumption turns out to be wrong for things like the ses
driver. Normally ses devices are not allowed to do runtime PM, but
userspace can override this setting. If this happens, the kernel gets
a NULL pointer dereference when blk_post_runtime_resume() tries to use
the uninitialized q->dev pointer.
This patch fixes the problem by calling the block layer's runtime-PM
routines only if the device's driver really does have a runtime-PM
callback routine. Since ses doesn't define any such callbacks, the
crash won't occur.
This fixes Bugzilla #101371.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Stanisław Pitucha <viraptor@gmail.com> Reported-by: Ilan Cohen <ilanco@gmail.com> Tested-by: Ilan Cohen <ilanco@gmail.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <JBottomley@Odin.com>
Hiral Shah [Tue, 14 Jul 2015 14:08:57 +0000 (07:08 -0700)]
fnic: Use the local variable instead of I/O flag to acquire io_req_lock in fnic_queuecommand() to avoid deadloack
We added changes in fnic driver patch 1.6.0.16 to acquire
io_req_lock in fnic_queuecommand() before issuing I/O so that io completion
is serialized. But when releasing the lock we check for the I/O flag and
this could be modified if IO abort occurs before I/O completion. In this case
we wont release the lock and causes deadlock in some scenerios. Using the
local variable to check the IO lock status will resolve the problem.
Fixes: 41df7b02db82cf6c14f094757bac3830d10a827f Signed-off-by: Hiral Shah <hishah@cisco.com> Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com> Signed-off-by: Anil Chintalapati <achintal@cisco.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <JBottomley@Odin.com>
Linus Torvalds [Tue, 18 Aug 2015 14:55:05 +0000 (07:55 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"These came in late last week, I wanted to look over the mst one before
forwarding, but it seems good.
Just three i915 and one MST fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Commit planes on each crtc separately.
drm/i915: calculate primary visibility changes instead of calling from set_config
drm/i915: Only dither on 6bpc panels
drm/dp/mst: Remove port after removing connector.
Eric Dumazet [Mon, 17 Aug 2015 17:18:48 +0000 (10:18 -0700)]
timer: Write timer->flags atomically
lock_timer_base() cannot prevent the following :
CPU1 ( in __mod_timer()
timer->flags |= TIMER_MIGRATING;
spin_unlock(&base->lock);
base = new_base;
spin_lock(&base->lock);
// The next line clears TIMER_MIGRATING
timer->flags &= ~TIMER_BASEMASK;
CPU2 (in lock_timer_base())
see timer base is cpu0 base
spin_lock_irqsave(&base->lock, *flags);
if (timer->flags == tf)
return base; // oops, wrong base
timer->flags |= base->cpu // too late
We must write timer->flags in one go, otherwise we can fool other cpus.
Fixes: bc7a34b8b9eb ("timer: Reduce timer migration overhead if disabled") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jon Christopherson <jon@jons.org> Cc: David Miller <davem@davemloft.net> Cc: xen-devel@lists.xen.org Cc: david.vrabel@citrix.com Cc: Sander Eikelenboom <linux@eikelenboom.it> Link: http://lkml.kernel.org/r/1439831928.32680.11.camel@edumazet-glaptop2.roam.corp.google.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Thomas Gleixner <tglx@linutronix.de>
Masahiro Yamada [Mon, 17 Aug 2015 03:03:33 +0000 (04:03 +0100)]
ARM: 8418/1: add boot image dependencies to not generate invalid images
U-Boot is often used to boot the kernel on ARM boards, but uImage
is not built by "make all", so we are often inclined to do
"make all uImage" to generate DTBs, modules and uImage in a single
command, but we should notice a pitfall behind it. In fact,
"make all uImage" could generate an invalid uImage if it is run with
the parallel option (-j).
You can reproduce this problem with the following procedure:
[1] First, build "all" and "uImage" separately.
You will get a valid uImage
$ git clean -f -x -d
$ export CROSS_COMPILE=<your-tools-prefix>
$ make -s -j8 ARCH=arm multi_v7_defconfig
$ make -s -j8 ARCH=arm all
$ make -j8 ARCH=arm UIMAGE_LOADADDR=0x80208000 uImage
CHK include/config/kernel.release
CHK include/generated/uapi/linux/version.h
CHK include/generated/utsrelease.h
make[1]: `include/generated/mach-types.h' is up to date.
CHK include/generated/timeconst.h
CHK include/generated/bounds.h
CHK include/generated/asm-offsets.h
CALL scripts/checksyscalls.sh
CHK include/generated/compile.h
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
UIMAGE arch/arm/boot/uImage
Image Name: Linux-4.2.0-rc5-00156-gdd2384a-d
Created: Sat Aug 8 23:21:35 2015
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6138648 Bytes = 5994.77 kB = 5.85 MB
Load Address: 80208000
Entry Point: 80208000
Image arch/arm/boot/uImage is ready
$ ls -l arch/arm/boot/*Image
-rwxrwxr-x 1 masahiro masahiro 13766656 Aug 8 23:20 arch/arm/boot/Image
-rw-rw-r-- 1 masahiro masahiro 6138712 Aug 8 23:21 arch/arm/boot/uImage
-rwxrwxr-x 1 masahiro masahiro 6138648 Aug 8 23:20 arch/arm/boot/zImage
[2] Update some source file(s)
$ touch init/main.c
[3] Then, re-build "all" and "uImage" simultaneously.
You will get an invalid uImage at random.
$ make -j8 ARCH=arm UIMAGE_LOADADDR=0x80208000 all uImage
CHK include/config/kernel.release
CHK include/generated/uapi/linux/version.h
CHK include/generated/utsrelease.h
make[1]: `include/generated/mach-types.h' is up to date.
CHK include/generated/timeconst.h
CHK include/generated/bounds.h
CHK include/generated/asm-offsets.h
CALL scripts/checksyscalls.sh
CC init/main.o
CHK include/generated/compile.h
LD init/built-in.o
LINK vmlinux
LD vmlinux.o
MODPOST vmlinux.o
GEN .version
CHK include/generated/compile.h
UPD include/generated/compile.h
CC init/version.o
LD init/built-in.o
KSYM .tmp_kallsyms1.o
KSYM .tmp_kallsyms2.o
LD vmlinux
SORTEX vmlinux
SYSMAP System.map
OBJCOPY arch/arm/boot/Image
Building modules, stage 2.
Kernel: arch/arm/boot/Image is ready
GZIP arch/arm/boot/compressed/piggy.gzip
AS arch/arm/boot/compressed/piggy.gzip.o
Kernel: arch/arm/boot/Image is ready
LD arch/arm/boot/compressed/vmlinux
GZIP arch/arm/boot/compressed/piggy.gzip
OBJCOPY arch/arm/boot/zImage
Kernel: arch/arm/boot/zImage is ready
UIMAGE arch/arm/boot/uImage
Image Name: Linux-4.2.0-rc5-00156-gdd2384a-d
Created: Sat Aug 8 23:23:14 2015
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 26472 Bytes = 25.85 kB = 0.03 MB
Load Address: 80208000
Entry Point: 80208000
Image arch/arm/boot/uImage is ready
MODPOST 192 modules
AS arch/arm/boot/compressed/piggy.gzip.o
LD arch/arm/boot/compressed/vmlinux
OBJCOPY arch/arm/boot/zImage
Kernel: arch/arm/boot/zImage is ready
$ ls -l arch/arm/boot/*Image
-rwxrwxr-x 1 masahiro masahiro 13766656 Aug 8 23:23 arch/arm/boot/Image
-rw-rw-r-- 1 masahiro masahiro 26536 Aug 8 23:23 arch/arm/boot/uImage
-rwxrwxr-x 1 masahiro masahiro 6138648 Aug 8 23:23 arch/arm/boot/zImage
Please notice the uImage is extremely small when this issue is
encountered. Besides, "Kernel: arch/arm/boot/zImage is ready" is
displayed twice, before and after the uImage log.
The root cause of this is the race condition between zImage and
uImage. Actually, uImage depends on zImage, but the dependency
between the two is only described in arch/arm/boot/Makefile.
Because arch/arm/boot/Makefile is not included from the top-level
Makefile, it cannot know the dependency between zImage and uImage.
Consequently, when we run make with the parallel option, Kbuild
updates vmlinux first, and then two different threads descends into
the arch/arm/boot/Makefile almost at the same time, one for updating
zImage and the other for uImage. While one thread is re-generating
zImage, the other also tries to update zImage before creating uImage
on top of that. zImage is overwritten by the slower thread and then
uImage is created based on the half-written zImage.
This is the reason why "Kernel: arch/arm/boot/zImage is ready" is
displayed twice, and a broken uImage is created.
The same problem could happen on bootpImage.
This commit adds dependencies among Image, zImage, uImage, and
bootpImage to arch/arm/Makefile, which is included from the
top-level Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mmap semaphore should not be taken when page faults are disabled.
Since pagefault_disable() no longer disables preemption, we now need
to use faulthandler_disabled() in place of in_atomic().
Signed-off-by: Nicolas Pitre <nico@linaro.org> Tested-by: Mark Salter <msalter@redhat.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ralf Baechle [Tue, 18 Aug 2015 09:25:50 +0000 (11:25 +0200)]
MIPS: Fix LLVM build issue.
Matthew Fortune <Matthew.Fortune@imgtec.com> reports:
The genex.S file appears to mix the case of a macro between its definition and
use. A cut down example of this is below. The macro __build_clear_none has
lower case 'build' but ends up being instantiated with upper case BUILD. Can
this be fixed on master. It has been picked up by the LLVM integrated assembler
which is currently case sensitive. We are likely to fix the assembler as well
but the code is currently inconsistent in the kernel.
Mark Brown [Sat, 15 Aug 2015 15:24:20 +0000 (08:24 -0700)]
ASoC: topology: Add Kconfig option for topology
Allow the topology code to be compiled out so that users who don't need
topology don't need to havve the code compiled in, saving them some
memory.
Some more configuration could be added to remove some of the hooks into
the core data structures but that is probably best done with some
refactoring to use functions to do the updates of the data structures
rather than ifdefing in the code as we'd need to do at the minute.
Suggested-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Torvalds [Mon, 17 Aug 2015 23:20:45 +0000 (16:20 -0700)]
Merge branch 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Three minor device-specific fixes and revert of NCQ autosense added
during this -rc1.
It turned out that NCQ autosense as currently implemented interferes
with the usual error handling behavior. It will be revisited in the
near future"
* 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: ahci_brcmstb: Fix misuse of IS_ENABLED
sata_sx4: Check return code from pdc20621_i2c_read()
Revert "libata: Implement NCQ autosense"
Revert "libata: Implement support for sense data reporting"
Revert "libata-eh: Set 'information' field for autosense"
ata: ahci_brcmstb: Fix warnings with CONFIG_PM_SLEEP=n
Linus Torvalds [Mon, 17 Aug 2015 23:15:26 +0000 (16:15 -0700)]
Merge branch 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
"A fix for a subtle bug introduced back during 3.17 cycle which
interferes with setting configurations under specific conditions"
* 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cpuset: use trialcs->mems_allowed as a temp variable
Ivan Vecera [Fri, 14 Aug 2015 20:30:01 +0000 (22:30 +0200)]
be2net: avoid vxlan offloading on multichannel configs
VxLAN offloading is not functional if the NIC is running in multichannel
mode (UMC, FLEX-10, VNIC...). Enabling this additionally kills whole
connectivity through the NIC and the device needs to be down and up to
restore it. The firmware should take care about it and does not allow
the conversion of interface to tunnel type (be_cmd_manage_iface) or should
support VxLAN offloading if multichannel config is enabled.
I have tested this on the latest available firmware (10.6.144.21).
Result:
[root@sm-04 ~]# ip link set enp5s0f0 up[root@sm-04 ~]# ip addr add 172.30.10.50/24 dev enp5s0f0
[root@sm-04 ~]# ping -c 3 172.30.10.254PING 172.30.10.254 (172.30.10.254) 56(84) bytes of data.
64 bytes from 172.30.10.254: icmp_seq=1 ttl=64 time=0.317 ms
64 bytes from 172.30.10.254: icmp_seq=2 ttl=64 time=0.187 ms
64 bytes from 172.30.10.254: icmp_seq=3 ttl=64 time=0.188 ms
--- 172.30.10.254 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2000ms
rtt min/avg/max/mdev = 0.187/0.230/0.317/0.063 ms
[root@sm-04 ~]# ip link add link enp5s0f0 vxlan10 type vxlan id 10 remote 172.30.10.60 dstport 4789
[root@sm-04 ~]# ip link set vxlan10 up
[ 7900.442811] be2net 0000:05:00.0: Enabled VxLAN offloads for UDP port 4789
[ 7900.455722] be2net 0000:05:00.1: Enabled VxLAN offloads for UDP port 4789
[ 7900.468635] be2net 0000:05:00.2: Enabled VxLAN offloads for UDP port 4789
[ 7900.481553] be2net 0000:05:00.3: Enabled VxLAN offloads for UDP port 4789
[root@sm-04 ~]# ping -c 3 172.30.10.254
PING 172.30.10.254 (172.30.10.254) 56(84) bytes of data.
[root@sm-04 ~]# ip link set vxlan10 down
[ 7959.434093] be2net 0000:05:00.0: Disabled VxLAN offloads for UDP port 4789
[ 7959.444792] be2net 0000:05:00.1: Disabled VxLAN offloads for UDP port 4789
[ 7959.455592] be2net 0000:05:00.2: Disabled VxLAN offloads for UDP port 4789
[ 7959.466416] be2net 0000:05:00.3: Disabled VxLAN offloads for UDP port 4789
[root@sm-04 ~]# ip link del vxlan10
[root@sm-04 ~]# ping -c 3 172.30.10.254
PING 172.30.10.254 (172.30.10.254) 56(84) bytes of data.
[root@sm-04 ~]# ip link set enp5s0f0 down
[root@sm-04 ~]# ip link set enp5s0f0 up
[ 8071.019003] be2net 0000:05:00.0 enp5s0f0: Link is Up
[root@sm-04 ~]# ping -c 3 172.30.10.254
PING 172.30.10.254 (172.30.10.254) 56(84) bytes of data.
64 bytes from 172.30.10.254: icmp_seq=1 ttl=64 time=0.318 ms
64 bytes from 172.30.10.254: icmp_seq=2 ttl=64 time=0.196 ms
64 bytes from 172.30.10.254: icmp_seq=3 ttl=64 time=0.194 ms
--- 172.30.10.254 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2000ms
rtt min/avg/max/mdev = 0.194/0.236/0.318/0.057 ms
Cc: Sathya Perla <sathya.perla@avagotech.com> Cc: Ajit Khaparde <ajit.khaparde@avagotech.com> Cc: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com> Cc: Sriharsha Basavapatna <sriharsha.basavapatna@avagotech.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Acked-by: Ajit Khaparde <ajit.khaparde@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Fri, 14 Aug 2015 18:05:54 +0000 (11:05 -0700)]
ipv6: Fix a potential deadlock when creating pcpu rt
rt6_make_pcpu_route() is called under read_lock(&table->tb6_lock).
rt6_make_pcpu_route() calls ip6_rt_pcpu_alloc(rt) which then
calls dst_alloc(). dst_alloc() _may_ call ip6_dst_gc() which takes
the write_lock(&tabl->tb6_lock). A visualized version:
Fixes: d52d3997f843 ("pv6: Create percpu rt6_info") Signed-off-by: Martin KaFai Lau <kafai@fb.com> CC: Hannes Frederic Sowa <hannes@stressinduktion.org> Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com> Signed-off-by: David S. Miller <davem@davemloft.net>