ARM: dts: imx: remove old DMA binding data from gpmi node
After mxs-dma driver adopts generic DMA device tree binding, gpmi
channel interrupt number is defined in DMA controller node, and
channel ID is listed in "dmas" property. So the DMA channel interrupt
number in gpmi node "interrupts" property and fsl,gpmi-dma-channel which
are used by old customized DMA binding can be removed now.
Alexander Shiyan [Sat, 13 Jul 2013 04:34:44 +0000 (08:34 +0400)]
ARM: dts: imx27: Add core voltages
This patch adds core voltages for i.MX27 CPUs. Only 266 and 400 MHz modes
is documented in the datasheet, so we add a 266 MHz frequency for conform this.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
ARM: dts: imx: share pad macro names between imx6q and imx6dl
The imx6q and imx6dl are two pin-to-pin compatible SoCs. The same board
design can work with either chip plugged into the socket, e.g. sabresd
and sabreauto boards.
We currently define pin groups in imx6q.dtsi and imx6dl.dtsi
respectively because the pad macro names are different between two
chips. This brings a maintenance burden on having the same label point
to the same pin group defined in two places.
The patch replaces prefix MX6Q_ and MX6DL_ with MX6QDL_ for both SoCs
pad macro names. Then the pin groups becomes completely common between
imx6q and imx6dl and can just be moved into imx6qdl.dtsi, so that the
long term maintenance of imx6q/dt pin settings becomes easier.
Unfortunately, the change brings some dramatic diff stat, but it's all
about DTS file, and the ultimate net diff stat is good.
Markus Pargmann [Fri, 28 Jun 2013 14:50:36 +0000 (16:50 +0200)]
ARM: dts: imx27 cpufreq-cpu0 frequencies
Set operating-points for imx27. There is no regulator support, so the
voltages are 0. The frequencies should be the same for all imx27 boards,
so it is defined here and can be overwritten if necessary.
Sascha Hauer [Tue, 25 Jun 2013 13:51:59 +0000 (15:51 +0200)]
ARM: dts: i.MX51 babbage: Add spi-cs-high property to pmic
The mc13892 driver knows that it needs spi-cs-high, so the mc13892
will work. The dataflash also connected to this bus though can only
be probed when the mc13892 is inactive. Due to driver potential
differences in the probe order we can only make sure the mc13892
is inactive when we put the information into the devicetree.
Sascha Hauer [Tue, 25 Jun 2013 13:51:45 +0000 (15:51 +0200)]
ARM: dts: i.MX6: sync imx6q and imx6dl pinmux entries
The i.MX6Q and i.MX6DL are pin compatible, so the pinmux entries
should be in sync. This patch systematically adds the pinmux entries
missing from the imx6q to the imx6dl file.
Some name inconsistencies and whitespace damage is fixed along the
way.
Shawn Guo [Thu, 22 Aug 2013 15:26:50 +0000 (23:26 +0800)]
Merge tag 'imx-soc-3.12' into imx/dt
It contains a bunch of imx soc updates for 3.12.
- Add more ethernet phy fixups for imx6 boards
- Add some missing imx6q clocks into clock driver
- Add new clock types fixup mux and div to work around some ugly
hardware defect
- Consolidate L2 cache initialization function, so that it can be used
on more i.MX SoCs
- Replace magic numbers in mach-imx6q.c with well defined macros
- Small fixes for imx6q and pllv3 clock drivers
- Some random updates on imx defconfig files
Dinh Nguyen [Tue, 13 Aug 2013 14:59:00 +0000 (09:59 -0500)]
phy: micrel: Add definitions for common Micrel PHY registers
Add defines for common Micrel PHY setups so that other platforms
can use them. Update imx61 and sama5 hardware to use the micrel_phy.h
PHY defines.
Also add support for the KSZ9021RLRN PHY.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: David S. Miller <davem@davemloft.net> CC: Andrew Victor <linux@maxim.org.za> CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Cc: netdev@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Commit 02502da45 (ASoC: imx-mc13783: Depend on ARCH_ARM) caused the selection of
CONFIG_SND_SOC_IMX_MC13783 to be impossible due to a wrong dependency, which
caused CONFIG_SND_SOC_IMX_MC13783 to be removed after the defconfigs cleanups.
The original selection problem has been fixed by 9f19de649f (ASoC: imx-mc13783:
Make SND_SOC_IMX_MC13783 visible again), so it is possible to select
CONFIG_SND_SOC_IMX_MC13783 again as originally done.
Current imx53_pm_init() implementation is incomplete as it lacks calling
suspend_set_ops().
Use a single imx5_pm_init() function to handle both mx51 and mx53.
This allows mx53 to enter in low-power mode.
Tested on a mx53qsb:
root@freescale /$ echo mem > /sys/power/state
PM: Syncing filesystems ... done.
mmc0: card e624 removed
Freezing user space processes ... (elapsed 0.001 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
... (Press Power button)
PM: suspend of devices complete after 17.067 msecs
PM: suspend devices took 0.020 seconds
PM: late suspend of devices complete after 0.954 msecs
PM: noirq suspend of devices complete after 1.288 msecs
Disabling non-boot CPUs ...
PM: noirq resume of devices complete after 0.680 msecs
PM: early resume of devices complete after 0.914 msecs
PM: resume of devices complete after 44.955 msecs
PM: resume devices took 0.050 seconds
Restarting tasks ... done.
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new SDHC card at address e624
mmcblk0: mmc0:e624 SU04G 3.69 GiB
mmcblk0: p1 p2 p3
libphy: 63fec000.etherne:00 - Link is Down
libphy: 63fec000.etherne:00 - Link is Up - 100/Full
root@freescale /$
The clock output on imx6q CCM_CLKO1 pad is not always cko1 clock, and
there is a multiplexer to select between cko1 and cko2. Add this
missing selection as the clock cko.
Peter Chen [Tue, 16 Jul 2013 02:23:20 +0000 (10:23 +0800)]
ARM: imx: clk-pllv3: improve the timeout waiting method
There are two improvements for this commit:
- Add comparing pll lock condition after while loop. It can
fix potential fake timeout problem caused by the code is just
scheduled out before compare the timeout, and the time of
scheduling out are more than one jiffies.
- Move timeout assignment more close to compare the timeout.
It can reduce the possibility the code is scheduled out, and
the timeout can be more precise.
Liu Ying [Thu, 4 Jul 2013 09:57:17 +0000 (17:57 +0800)]
ARM: imx6: change some clocks to fixup clocks
All the clocks controlled by the register 'CCM Serial Clock
Multiplexer Register 1' should be fixup clocks. This patch
changes those clocks from basic multiplexer or divider clocks
to fixup clocks.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Liu Ying [Thu, 4 Jul 2013 09:35:46 +0000 (17:35 +0800)]
ARM: imx: add common clock support for fixup mux
One register may have several fields to control some clocks. It
is possible that the read/write values of some fields may map to
different real functional values, so writing to the other fields
in the same register may break a working clock tree. A real case
is the aclk_podf field in the register 'CCM Serial Clock Multiplexer
Register 1' of i.MX6Q/SDL SoC. This patch introduces a fixup hook
for multiplexer clock which is called before writing a value to
clock registers to support this kind of multiplexer clocks.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Liu Ying [Thu, 4 Jul 2013 09:22:26 +0000 (17:22 +0800)]
ARM: imx: add common clock support for fixup div
One register may have several fields to control some clocks. It
is possible that the read/write values of some fields may map to
different real functional values, so writing to the other fields
in the same register may break a working clock tree. A real case
is the aclk_podf field in the register 'CCM Serial Clock Multiplexer
Register 1' of i.MX6Q/SDL SoC. This patch introduces a fixup hook
for divider clock which is called before writing a value to clock
registers to support this kind of divider clocks.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Vincent Stehlé [Wed, 10 Jul 2013 09:45:46 +0000 (11:45 +0200)]
ARM: imx: fix imx_init_l2cache storage class
This fixes the following compilation error:
arch/arm/mach-imx/system.c:101:123: error: static declaration of ‘imx_init_l2cache’ follows non-static declaration
In file included from arch/arm/mach-imx/system.c:32:0:
arch/arm/mach-imx/common.h:165:13: note: previous declaration of ‘imx_init_l2cache’ was here
arch/arm/mach-imx/system.c:101:123: warning: ‘imx_init_l2cache’ defined but not used [-Wunused-function]
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Russell King <linux@arm.linux.org.uk> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
ARM: imx: let L2 initialization be a common function
Move imx6q L2 initialization function imx6q_init_l2cache() into
system.c, and rename it imx_init_l2cache(), so that other platforms
other than imx6q can also use the function.
projects / linux-beck.git / log