Hans de Goede [Sat, 13 Sep 2014 10:26:32 +0000 (12:26 +0200)]
uas: Do not use scsi_host_find_tag
Using scsi_host_find_tag with tags returned by the device is unsafe for
multiple reasons:
1) It returns tags->rqs[tag], which may be non NULL even when the cmnd is
not owned by us
2) It returns tags->rqs[tag], without holding any locks protecting it
3) It returns tags->rqs[tag], without doing any boundary checking
Instead keep our own list which maps tags -> inflight cmnds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Sat, 13 Sep 2014 10:26:30 +0000 (12:26 +0200)]
uas: Fix resetting flag handling
- Make sure we always hold the lock when setting / checking resetting
- Check resetting before checking urb->status
- Add missing check for resetting to uas_data_cmplt
- Add missing check for resetting to uas_do_work
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are various bug reports about oopses / hangs with the uas driver,
which all point to the abort-command and logical-unit-reset (task-management)
error handling paths.
Getting these right is very hard, there are quite a few corner cases, and
testing is almost impossible since under normal operation these code paths
are not used at all.
Another problem is that there are also some cases where it simply is not clear
what to do at all. E.g. over usb-2 multiple outstanding commands share the same
endpoint. What if a command gets aborted while its sense urb is half way
through completing (so some data has been transfered but not all). Since the
urb is not yet complete we don't know if the sense urb is actually for this
command, or for one of the other oustanding commands. If it is for one of the
other commands and we cancel it, then we end up in an undefined state. But if
it is actually for the command we're aborting, and the abort succeeds, then it
may never complete...
This exact same problem applies to logical unit resets too, if there are
multiple luns, then commands outstanding on both luns share the sense
endpoint. If there is only a single lun, then doing a logical unit reset is
little better then doing a full usb device reset.
So summarizing because:
1) abort / lun-reset is very tricky to get right
2) Not being able to test the tricky code, which means it will have bugs
3) This being a code path which under normal operation will never happen,
so being slow / sub-optimal here is not really an issue
4) Under error conditions we will still be able to recover through usb
device resets.
5) This may be a bit slower in some cases, but this is actually faster in
cases where the bridge ship has locked up, which seems to be the most
common error case sofar.
This commit removes the abort / lun-reset error handling paths, and also the
taks-mgmt code since those are the only 2 task-mgmt users. Leaving only the
(tested and testable) usb-device-reset error handling path in place.
Note I realize that this is somewhat of a big hammer, but currently people
are seeing very hard to debug oopses with uas. First let focus on making uas
work reliable, then we can later look into adding more fine grained error
handling.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Tue, 16 Sep 2014 16:36:52 +0000 (18:36 +0200)]
uas: Add no-report-opcodes quirk
Besides the ASM1051 (*) needing sdev->no_report_opcodes = 1, it turns out that
the JMicron JMS567 also needs it to work properly with uas (usb-storage always
sets it). Since some of the scsi devs were not to keen on the idea to
outrightly set sdev->no_report_opcodes = 1 for all uas devices, so add a quirk
for this, and set it for the JMS567.
*) Which has become a non-issue since we've completely blacklisted uas on
the ASM1051 for other reasons
Cc: stable@vger.kernel.org Reported-and-tested-by: Claudio Bizzarri <claudio.bizzarri@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While at it also add missing documentation for the u value for usb-storage
quirks.
Cc: stable@vger.kernel.org # 3.16, 3.17 Signed-off-by: Hans de Goede <hdegoede@redhat.com>
--
Changes in v2: Add documentation for new t and u usb-storage.quirks flags
Changes in v3: Fix typo in documentation
Changes in v4: Also apply the quirk to (0bc2:3312)
Changes in v5: Rebased on 3.17-rc5, drop u documentation, already upstream Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sanjeev Sharma [Tue, 12 Aug 2014 06:40:21 +0000 (12:10 +0530)]
uas: replace WARN_ON_ONCE() with lockdep_assert_held()
on some architecture spin_is_locked() always return false in
uniprocessor configuration and therefore it would be advise
to replace with lockdep_assert_held().
Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Griffin [Mon, 8 Sep 2014 12:04:48 +0000 (13:04 +0100)]
MAINTAINERS: Add ehci-st.c and ohci-st.c to ARCH/STI architecture
This patch adds the ehci-st.c and ohci-st.c files for the usb 2.0
& usb1.1 host controller drivers found on stih41x and stih4xx STMicroelectronics
SoC's into the STI arch section of the maintainers file.
Peter Chen [Mon, 22 Sep 2014 00:14:16 +0000 (08:14 +0800)]
usb: chipidea: otg initialization is only needed when the gadget is supported
We have only needed to enable otg initialization when both of
below conditions are satisfied:
- The controller is otg capable
- The gadget function is enabled
If the controller is otg capable, but is host-only configuration, we do
not need to access register otgsc and do any otg operations (eg, create
otg workqueue).
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stefan Agner [Mon, 22 Sep 2014 00:14:15 +0000 (08:14 +0800)]
chipidea: usbmisc_imx: Add USB support for VF610 SoCs
This adds Vybrid VF610 SoC support. The IP is very similar to i.MX6,
however, the non-core registers are spread in two different register
areas. Hence we support multiple instances of the USB misc driver
and add the driver instance to the imx_usbmisc_data structure.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Tue, 19 Aug 2014 01:51:56 +0000 (09:51 +0800)]
usb: chipidea: add TPL support for targeted hosts
For OTG and Embedded hosts, they may need TPL (Targeted Peripheral List)
for usb certification and other vender specific requirements, the
platform can tell chipidea core driver if it supports tpl through DT
or platform data.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Tue, 19 Aug 2014 01:51:55 +0000 (09:51 +0800)]
usb: common: add API to get if the platform supports TPL
The TPL (Targeted Peripheral List) is used for targeted hosts
(non-PC hosts), and it can be used at USB OTG & EH certification
and some specific products which need white list.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Tue, 19 Aug 2014 01:51:53 +0000 (09:51 +0800)]
usb: core: TPL should apply for both OTG and EH
According to On-The-Go and Embedded Host Supplement to the USB Revision
2.0 Specification, the targeted hosts (non-PC hosts) include both
embedded hosts and otg, and each targeted host product defines the
set of supported peripherals on a TPL (Targeted Peripheral List). So,
TPL should apply for both OTG and embedded host, and the otg support is
not a must for embedded host.
The TPL support feature will only be effect when CONFIG_USB_OTG_WHITELIST
has been chosen and hcd->tpl_support flag is set, it can avoid the enumeration
fails problem for the user who chooses CONFIG_USB_OTG_WHITELIST wrongly.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Mon, 25 Aug 2014 15:51:27 +0000 (17:51 +0200)]
USB: quirks: enable device-qualifier quirk for Elan Touchscreen
Enable device-qualifier quirk for Elan Touchscreen, which often fails to
handle requests for the device_descriptor.
Note that the device sometimes do respond properly with a Request Error
(three times as USB core retries), but usually fails to respond at all.
When this happens any further descriptor requests also fails, for
example:
[ 1528.688934] usb 2-7: new full-speed USB device number 4 using xhci_hcd
[ 1530.945588] usb 2-7: unable to read config index 0 descriptor/start: -71
[ 1530.945592] usb 2-7: can't read configurations, error -71
This has been observed repeating for over a minute before eventual
successful enumeration.
Reported-by: Drew Von Spreecken <drewvs@gmail.com> Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Mon, 25 Aug 2014 15:51:26 +0000 (17:51 +0200)]
USB: core: add device-qualifier quirk
Add new quirk for devices that cannot handle requests for the
device_qualifier descriptor.
A USB-2.0 compliant device must respond to requests for the
device_qualifier descriptor (even if it's with a request error), but at
least one device is known to misbehave after such a request.
That commit causes more problem than fixes. Firstly, kfree()
should be called after usb_ep_dequeue() and secondly, the way
things are, we will try to dequeue a request that has already
completed much more frequently than one which is pending.
Cc: Li Jun <b47624@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Cc: stable <stable@vger.kernel.org> # 3.17 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Fixes for ARM, the most notable being the fix from Nathan Lynch to fix
the state of various registers during execve, to ensure that data
can't be leaked between two executables.
Fixes from Victor Kamensky for get_user() on big endian platforms,
since the addition of 8-byte get_user() support broke these fairly
badly.
A fix from Sudeep Holla for affinity setting when hotplugging CPU 0.
A fix from Stephen Boyd for a perf-induced sleep attempt while atomic.
Lastly, a correctness fix for emulation of the SWP instruction on
ARMv7+, and a fix for wrong carry handling when updating the
translation table base address on LPAE platforms"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8149/1: perf: Don't sleep while atomic when enabling per-cpu interrupts
ARM: 8148/1: flush TLS and thumbee register state during exec
ARM: 8151/1: add missing exports for asm functions required by get_user macro
ARM: 8137/1: fix get_user BE behavior for target variable with size of 8 bytes
ARM: 8135/1: Fix in-correct barrier usage in SWP{B} emulation
ARM: 8133/1: use irq_set_affinity with force=false when migrating irqs
ARM: 8132/1: LPAE: drop wrong carry flag correction after adding TTBR1_OFFSET
Merge tag 'media-v3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"some media bug fixes:
- a Kconfig dependency issue
- some fixes for af9033/it913x demod to be more reliable and address
a performance regression
- cx18: fix an oops on devices with tda8290 tuner
- two new USB IDs for af9035
- a couple fixes on smapp driver"
* tag 'media-v3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] af9035: new IDs: add support for PCTV 78e and PCTV 79e
[media] af9033: feed clock to RF tuner
[media] it913x: init tuner on attach
[media] af9033: update IT9135 tuner inittabs
[media] Kconfig: do not select SPI bus on sub-driver auto-select
[media] cx18: fix kernel oops with tda8290 tuner
[media] smiapp: Set sub-device owner
[media] smiapp: Fix power count handling
Merge tag 'staging-3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO fixes from Greg KH:
"Here are some IIO and Staging driver fixes for 3.17-rc6. They are all
pretty simple, and resolve reported issues"
* tag 'staging-3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vt6655: buffer overflow in ioctl
iio:magnetometer: bugfix magnetometers gain values
iio: adc: at91: don't use the last converted data register
iio: adc: xilinx-xadc: assign auxiliary channels address correctly
iio: meter: ade7758: Fix indio_dev->trig assignment
iio: inv_mpu6050: Fix indio_dev->trig assignment
iio: gyro: itg3200: Fix indio_dev->trig assignment
iio: st_sensors: Fix indio_dev->trig assignment
iio: hid_sensor_hub: Fix indio_dev->trig assignment
iio: adc: ad_sigma_delta: Fix indio_dev->trig assignment
iio: accel: bma180: Fix indio_dev->trig assignment
iio:trigger: modify return value for iio_trigger_get
iio:inkern: fix overwritten -EPROBE_DEFER in of_iio_channel_get_by_name
Merge tag 'usb-3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes / quirks from Greg KH:
"Here are some USB and PHY fixes and quirks for 3.17-rc6. Nothing
major, just a few things that have been reported"
* tag 'usb-3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters
USB: storage: Add quirk for Ariston Technologies iConnect USB to SCSI adapter
USB: storage: Add quirk for Adaptec USBConnect 2000 USB-to-SCSI Adapter
USB: EHCI: unlink QHs even after the controller has stopped
phy: spear1340-miphy: fix driver dependencies
phy: spear1310-miphy: fix driver dependencies
phy: miphy365x: Fix off-by-one error
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the target pending fixes for v3.17-rc6.
Included are Sagi's long overdue fixes related to iser-target
shutdown, along with a couple of fixes from Sebastian related to ALUA
Referrals changes that when in during the v3.14 time-frame.
Also included are a few iscsi-target fixes, most recently of which
where found during Joern's Coverity scanning of target code"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: avoid NULL pointer in iscsi_copy_param_list failure
iscsi-target: Fix memory corruption in iscsit_logout_post_handler_diffcid
target: Fix inverted logic in SE_DEV_ALUA_SUPPORT_STATE_STORE
target: Fix user data segment multiplier in spc_emulate_evpd_b3()
iscsi-target: Ignore ICF_GOT_LAST_DATAOUT during Data-Out ITT lookup
Target/iser: Fix initiator_depth and responder_resources
Target/iser: Avoid calling rdma_disconnect twice
Target/iser: Don't put isert_conn inside disconnected handler
Target/iser: Get isert_conn reference once got to connected_handler
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A bunch of radeon fixes for oops on module unload, and problems with
resetting the dma engine, one nouveau fix for black boxes in rendering
on my mbp retina, one sti fix, and a couple of intel fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: ltc/gf100-: fix cbc issues on certain boards
drm/bochs: add missing drm_connector_register call
drm/cirrus: add missing drm_connector_register call
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
drm/nouveau/runpm: fix module unload
drm/radeon/px: fix module unload
vgaswitcheroo: add vga_switcheroo_fini_domain_pm_ops
drm/radeon: don't reset dma on r6xx-evergreen init
drm/radeon: don't reset sdma on CIK init
drm/radeon: don't reset dma on NI/SI init
drm/radeon/dpm: fix resume on mullins
drm/radeon: Disable HDP flush before every CS again for < r600
drm/radeon: delete unused PTE_* defines
drm/i915: Add limited color range readout for HDMI/DP ports on g4x/vlv/chv
drm: sti: do not iterate over the info frame array
drm/i915: Fix SRC_COPY width on 830/845g
Ben Skeggs [Sat, 20 Sep 2014 07:39:00 +0000 (17:39 +1000)]
drm/nouveau: ltc/gf100-: fix cbc issues on certain boards
A mismatch between FB and LTC's idea of how big a large page is causes
issues such as black "holes" in rendering to occur on some boards
(those where LTC is configured for 64KiB large pages) when compression
is used.
Confirmed to fix at least the GK107 MBP.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Sat, 20 Sep 2014 07:23:37 +0000 (17:23 +1000)]
Merge branch 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
single fix for regression on rs4xx/rs690/rs740
* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
Paul Zimmerman [Tue, 16 Sep 2014 20:47:27 +0000 (13:47 -0700)]
usb: dwc2: handle DMA buffer unmapping sanely
The driver's handling of DMA buffers for non-aligned transfers
was kind of nuts. For IN transfers, it left the URB DMA buffer
mapped until the transfer completed, then synced it, copied the
data from the bounce buffer, then synced it again.
Instead of that, just call usb_hcd_unmap_urb_for_dma() to unmap
the buffer before starting the transfer. Then no syncing is
required when doing the copy. This should also allow handling of
other types of mappings besides just dma_map_single() ones.
Also reduce the size of the bounce buffer allocation for Isoc
endpoints to 3K, since that's the largest possible transfer size.
Tested on Raspberry Pi and Altera SOCFPGA.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Zimmerman [Tue, 16 Sep 2014 20:47:26 +0000 (13:47 -0700)]
usb: dwc2: clip max_transfer_size to 65535
Clip max_transfer_size to 65535 for host. dwc2_hc_setup_align_buf()
allocates coherent buffers with this size, and if it's too large we
can exhaust the coherent DMA pool.
Tested on Raspberry Pi and Altera SOCFPGA.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Robert Baldyga [Tue, 9 Sep 2014 08:44:56 +0000 (10:44 +0200)]
usb: dwc2/gadget: assign TX FIFO dynamically
Because we have not enough memory to have each TX FIFO of size at least
3072 bytes (the maximum single packet size with 3 transactions per
microframe), we create four FIFOs of lenght 1024, and four of length
3072 bytes, and assing them to endpoints dynamically according to
maxpacket size value of given endpoint.
Up to now there were initialized 16 TX FIFOs, but we use only 8 IN
endpoints, so we can split available memory for 8 FIFOs to have more
memory for each one.
It needed to do some small modifications in few places in code, because
there was assumption that TX FIFO numbers assigned to endpoints are the
same as the endpoint numbers, which is not true since we have dynamic
FIFO assigning.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'iio-fixes-3.17a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 3.17 cycle.
* Fix an overwritten error return that can prevent deferred probing when
using of_iio_channel_get_by_name
* A series that deals with an incorrect reference count when the default
trigger is set within the main probe routine for a driver. Can result
in a double free if the trigger is changed.
* Fix a buglet with xilinx-xadc concerning setup of the address for an
aux channel.
* At91 adc driver could sometimes get a touchscreen reading rather than
the intended adc channel. This is fixed by using the channel data register
instead.
* Fix some ST magnetometer gain values that differ in production parts from
the prerelease ones used for driver development.
Merge tag 'usb-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v3.18 merge window
Quite big pull request this time. Audio and UVC gadgets
can now be used with our configfs-based binding. We have
three PHY drivers being removed because a new one has been
added using new PHY framework.
Gadget framework got a new ->reset callback preparing for
some other changes to come on next merge window.
A few new drivers came in as well; among those we have a
new UDC driver from Xilinx and two new glue layers for
DWC3 (ST and Qualcomm).
DWC3 also learned about tracepoints which will help debugging
quite a bit.
Other than that, a big series of non-critical fixes and
cleanups.
All patches have been on linux-next for quite a bit of time
and I boot tested these changes on platforms I have access
to and work with mainline.
Mark [Wed, 17 Sep 2014 18:15:43 +0000 (19:15 +0100)]
USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters
This patch adds quirks for Entrega Technologies (later Xircom PortGear) USB-
SCSI converters. They use Shuttle Technology EUSB-01/EUSB-S1 chips. The
US_FL_SCM_MULT_TARG quirk is needed to allow multiple devices on the SCSI
chain to be accessed. Without it only the (single) device with SCSI ID 0
can be used.
The standalone converter sold by Entrega had model number U1-SC25. Xircom
acquired Entrega and re-branded the product line PortGear. The PortGear USB
to SCSI Converter (model PGSCSI) is internally identical to the Entrega
product, but later models may use a different USB ID. The Entrega-branded
units have USB ID 1645:0007, as does my Xircom PGSCSI, but the Windows and
Macintosh drivers also support 085A:0028.
Entrega also sold the "Mac USB Dock", which provides two USB ports, a Mac
(8-pin mini-DIN) serial port and a SCSI port. It appears to the computer as
a four-port hub, USB-serial, and USB-SCSI converters. The USB-SCSI part may
have initially used the same ID as the standalone U1-SC25 (1645:0007), but
later production used 085A:0026.
My Xircom PortGear PGSCSI has bcdDevice=0x0100. Units with bcdDevice=0x0133
probably also exist.
This patch adds quirks for 1645:0007, 085A:0026 and 085A:0028. The Windows
driver INF file also mentions 085A:0032 "PortStation SCSI Module", but I
couldn't find any mention of that actually existing in the wild; perhaps it
was cancelled before release?
Mark [Tue, 16 Sep 2014 15:51:41 +0000 (16:51 +0100)]
USB: storage: Add quirk for Ariston Technologies iConnect USB to SCSI adapter
Hi,
The Ariston Technologies iConnect 025 and iConnect 050 (also known as e.g.
iSCSI-50) are SCSI-USB converters which use Shuttle Technology/SCM
Microsystems chips. Only the connectors differ; both have the same USB ID.
The US_FL_SCM_MULT_TARG quirk is required to use SCSI devices with ID other
than 0.
I don't have one of these, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the products use.
Mark [Tue, 16 Sep 2014 15:22:50 +0000 (16:22 +0100)]
USB: storage: Add quirk for Adaptec USBConnect 2000 USB-to-SCSI Adapter
The Adaptec USBConnect 2000 is another SCSI-USB converter which uses
Shuttle Technology/SCM Microsystems chips. The US_FL_SCM_MULT_TARG quirk is
required to use SCSI devices with ID other than 0.
I don't have a USBConnect 2000, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the product uses.
Alan Stern [Wed, 17 Sep 2014 15:23:54 +0000 (11:23 -0400)]
USB: EHCI: unlink QHs even after the controller has stopped
Old code in ehci-hcd tries to expedite disabling endpoints after the
controller has stopped, by destroying the endpoint's associated QH
without first unlinking the QH. This was necessary back when the
driver wasn't so careful about keeping track of the controller's
state.
But now we are careful about it, and the driver knows that when the
controller isn't running, no unlinking delay is needed. Furthermore,
skipping the unlink step will trigger a BUG() in qh_destroy() when the
preceding QH is released, because the link pointer will be non-NULL.
Removing the lines that skip the unlinking step and go directly to
QH_STATE_IDLE fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Joe Lawrence <joe.lawrence@stratus.com> Tested-by: Joe Lawrence <joe.lawrence@stratus.com> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"I've got a revert to fix a regression with btrfs device registration,
and Filipe has part two of his fsync fix from last week"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Revert "Btrfs: device_list_add() should not update list when mounted"
Btrfs: set inode's logged_trans/last_log_commit after ranged fsync
Merge tag 'nfs-for-3.17-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client fixes from Trond Myklebust:
"Highligts:
- fix an Oops in nfs4_open_and_get_state
- fix an Oops in the nfs4_state_manager
- fix another bug in the close/open_downgrade code"
* tag 'nfs-for-3.17-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Fix another bug in the close/open_downgrade code
NFSv4: nfs4_state_manager() vs. nfs_server_remove_lists()
NFS: remove BUG possibility in nfs4_open_and_get_state
Merge tag 'pci-v3.17-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These fix:
- Boot video device detection on dual-GPU Apple systems
- Hotplug fiascos on VGA switcheroo with radeon & nouveau drivers
- Boot hang on Freescale i.MX6 systems
- Excessive "no hotplug settings from platform" warnings
In particular:
Enumeration
- Don't default exclusively to first video device (Bruno Prémont)
PCI device hotplug
- Remove "no hotplug settings from platform" warning (Bjorn Helgaas)
- Add pci_ignore_hotplug() for VGA switcheroo (Bjorn Helgaas)
Freescale i.MX6
- Put LTSSM in "Detect" state before disabling (Lucas Stach)"
* tag 'pci-v3.17-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
vgaarb: Drop obsolete #ifndef
vgaarb: Don't default exclusively to first video device with mem+io
ACPIPHP / radeon / nouveau: Remove acpi_bus_no_hotplug()
PCI: Remove "no hotplug settings from platform" warning
PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device
PCI: imx6: Put LTSSM in "Detect" state before disabling it
MAINTAINERS: Add Lucas Stach as co-maintainer for i.MX6 PCI driver
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of three fixes.
One represents a nasty shared tag map regression (another inverted
condition) caused by recent SCSI MQ patches, one is a longstanding
potential buffer overrun in the iscsi data buffer and the final one is
a use after free for the rare bidirectional commands"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] fix for bidi use after free
[SCSI] fix regression that accidentally disabled block-based tcq
[SCSI] libiscsi: fix potential buffer overrun in __iscsi_conn_send_pdu
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Two kernel side fixes: a kprobes fix and a perf_remove_from_context()
fix (which does not yet fix the migration bug which is WIP)"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix a race condition in perf_remove_from_context()
kprobes/x86: Free 'optinsn' cache when range check fails
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
EFI fixes, a build fix, a page table dumping (debug) fix and a clang
build fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/arm64: Fix fdt-related memory reservation
x86/mm: Apply the section attribute to the variable, not its type
x86/efi: Fixup GOT in all boot code paths
x86/efi: Only load initrd above 4g on second try
x86-64, ptdump: Mark espfix area only if existent
x86, irq: Fix build error caused by 9eabc99a635a77cbf09
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"A fair number of build fixes for various configurations.
Fixes to BPF, and the BCM47xx platform code, a preemption fix for the
Loongson core, a syscall auditing fix, wire up the new getrandom and
memfd_create. Several patches for EVA"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (30 commits)
MIPS: SmartMIPS: Disable assembler warnings
MIPS: Move CPU topology macros to topology.h
MIPS: Wire up new syscalls getrandom and memfd_create.
MIPS: Fix a warning for virt_to_page
arch/mips/net/bpf_jit.c: fix failure check
MIPS: COP2: CPP macro safety fixes.
MIPS: Kconfig: Select SMP symbols for CMP
MIPS: ZBOOT: add missing <linux/string.h> include
MIPS: IP28: Fix/clean spaces.h
MIPS: IP28: Select correct L1_CACHE_SHIFT
MIPS: BCM63xx: delete double assignment
MIPS: Spelling s/confugrations/configurations/
MIPS: OCTEON: make get_system_type() thread-safe
MIPS: CPS: Initialize EVA before bringing up VPEs from secondary cores
MIPS: Malta: EVA: Rename 'eva_entry' to 'platform_eva_init'
MIPS: EVA: Add new EVA header
MIPS: scall64-o32: Fix indirect syscall detection
MIPS: syscall: Fix AUDIT value for O32 processes on MIPS64
MIPS: Loongson: Fix COP2 usage for preemptible kernel
MIPS: NL: Fix nlm_xlp_defconfig build error
...
When ending a bi-directionional SCSI request, blk_finish_request()
cleans up and frees the request, but scsi_release_bidi_buffers() tries
to indirect through the request to find it's data buffers. This causes
a panic due to a null pointer dereference.
Move the call to scsi_release_bidi_buffers() before the call to
blk_finish_request().
Signed-off-by: Daniel Gryniewicz <dang@linuxbox.com> Reviewed-by: Webb Scales <webbnh@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] fix regression that accidentally disabled block-based tcq
The scsi blk-mq support accidentally flipped a conditional, which lead to
never enabling block based tcq when using the legacy request path.
Fixes: d285203cf647d7c9 scsi: add support for a blk-mq based I/O path. Reported-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mike Christie [Wed, 3 Sep 2014 05:00:39 +0000 (00:00 -0500)]
[SCSI] libiscsi: fix potential buffer overrun in __iscsi_conn_send_pdu
This patches fixes a potential buffer overrun in __iscsi_conn_send_pdu.
This function is used by iscsi drivers and userspace to send iscsi PDUs/
commands. For login commands, we have a set buffer size. For all other
commands we do not support data buffers.
This was reported by Dan Carpenter here:
http://www.spinics.net/lists/linux-scsi/msg66838.html
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Michel Dänzer [Fri, 19 Sep 2014 01:22:46 +0000 (10:22 +0900)]
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83996 Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dave Airlie [Fri, 19 Sep 2014 00:34:34 +0000 (10:34 +1000)]
Merge tag 'drm-intel-fixes-2014-09-18' of git://anongit.freedesktop.org/drm-intel into drm-fixes
couple of display fixes.
* tag 'drm-intel-fixes-2014-09-18' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Add limited color range readout for HDMI/DP ports on g4x/vlv/chv
drm/i915: Fix SRC_COPY width on 830/845g
Dave Airlie [Fri, 19 Sep 2014 00:34:06 +0000 (10:34 +1000)]
Merge branch 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
- fix a resume hang on mullins
- fix an oops on module unload with vgaswitcheroo (radeon and nouveau)
- fix possible hangs DMA engine hangs due to hw bugs
* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
drm/nouveau/runpm: fix module unload
drm/radeon/px: fix module unload
vgaswitcheroo: add vga_switcheroo_fini_domain_pm_ops
drm/radeon: don't reset dma on r6xx-evergreen init
drm/radeon: don't reset sdma on CIK init
drm/radeon: don't reset dma on NI/SI init
drm/radeon/dpm: fix resume on mullins
drm/radeon: Disable HDP flush before every CS again for < r600
drm/radeon: delete unused PTE_* defines
Reviewed-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Cc: Ben Skeggs <bskeggs@redhat.com>
Michel Dänzer [Wed, 17 Sep 2014 07:25:55 +0000 (16:25 +0900)]
drm/radeon: Disable HDP flush before every CS again for < r600
It was causing display corruption with R300 generation GPUs at least.
Reported-and-Tested-by: Mikael Pettersson <mikpelinux@gmail.com> Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
./arch/arm64/include/asm/pgtable.h:27:0: note: this is the location of the previous definition
#define PTE_VALID (_AT(pteval_t, 1) << 0)
^
In file included from drivers/gpu/drm/radeon/r600_cs.c:31:0:
drivers/gpu/drm/radeon/r600d.h:48:0: warning: "PTE_VALID" redefined [enabled by default]
#define PTE_VALID (1 << 0)
^
In file included from ./arch/arm64/include/asm/io.h:29:0,
from include/linux/clocksource.h:19,
from include/clocksource/arm_arch_timer.h:19,
from ./arch/arm64/include/asm/arch_timer.h:27,
from ./arch/arm64/include/asm/timex.h:19,
from include/linux/timex.h:65,
<snip>
from include/drm/drmP.h:51,
from drivers/gpu/drm/radeon/r600_cs.c:29:
./arch/arm64/include/asm/pgtable.h:27:0: note: this is the location of the previous definition
#define PTE_VALID (_AT(pteval_t, 1) << 0)
^
Signed-off-by: Kyle McMartin <kyle@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs/smb3 fixes from Steve French:
"Fixes for problems found during testing and debugging at the SMB3
storage test event (plugfest) this week"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
Fix mfsymlinks file size check
Update version number displayed by modinfo for cifs.ko
cifs: remove dead code
Revert "cifs: No need to send SIGKILL to demux_thread during umount"
[SMB3] Fix oops when creating symlinks on smb3
[CIFS] Fix setting time before epoch (negative time values)
Merge tag 'sound-3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All small fixes in random various drivers, mostly for ASoC at this
time, which look reasonable for a high rc number"
* tag 'sound-3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: rockchip-i2s: dt: swap tx and rx channed request number in example
ASoC: rockchip-i2s: fix registers' property of rockchip i2s controller
ASoC: rockchip-i2s: fix master mode set bit error
ASoC: cs4265: Fix register address to set the proper data type.
ALSA: hda - Fix invalid pin powermap without jack detection
ASoC: soc-pcm: fix dpcm_path_get error handling
ASoC: samsung-i2s: Check secondary DAI exists before referencing
ASoC: Update email id of the author
ASoC: dwc: Update email id of the author
ASoC: davinci-mcasp: Correct rx format unit configuration
ASoC: tlv320aic31xx: Fix 24bit samples with I2S format and 12MHz mclk
Krzysztof Hałasa [Thu, 18 Sep 2014 13:12:02 +0000 (15:12 +0200)]
Fix unbalanced mutex in dma_pool_create().
dma_pool_create() needs to unlock the mutex in error case. The bug was
introduced in the 3.16 by commit cc6b664aa26d ("mm/dmapool.c: remove
redundant NULL check for dev in dma_pool_create()")/
Merge tag 'regulator-v3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"Fix some leaked OF node references in regulator drivers that have been
left over following a fix on a fix to the reference counting"
* tag 'regulator-v3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: remove unnecessary of_node_get() to parent
Merge tag 'spi-v3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes for v3.17:
- Fix davinci so that GPIO chip selects work with deferred probe of
GPIOs (which could happen in production depending on kernel config)
plus one incremental stylistic fix to that.
- Several fixes for the newly introduced rockchip driver that came up
in wider testing of the device.
- A couple of small things in the sirf driver, one bug that would
stop DMA transfers working and another update to follow the
documented procedure in the datasheet.
- Fix some memory leaks with devm_kzalloc() being used outside of the
device bind path"
* tag 'spi-v3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: davinci: remove empty function davinci_spi_cleanup
spi: davinci: request cs_gpio's from probe
spi/pl022: Fix error message
spi/rockchip: Mark DMA as optional
spi/rockchip: Don't warn if SPI is busy but disabled
spi/rockchip: Fix the wait_for_idle() timeout
spi: sirf: add fifo reset/start for cmd transfer
spi: sirf: enable RX_IO_DMA_INT interrupt
spi: dw: Don't use devm_kzalloc in master->setup callback
spi: fsl: Don't use devm_kzalloc in master->setup callback
NFSv4: Fix another bug in the close/open_downgrade code
James Drew reports another bug whereby the NFS client is now sending
an OPEN_DOWNGRADE in a situation where it should really have sent a
CLOSE: the client is opening the file for O_RDWR, but then trying to
do a downgrade to O_RDONLY, which is not allowed by the NFSv4 spec.
Reported-by: James Drews <drews@engr.wisc.edu> Link: http://lkml.kernel.org/r/541AD7E5.8020409@engr.wisc.edu Fixes: aee7af356e15 (NFSv4: Fix problems with close in the presence...) Cc: stable@vger.kernel.org # 2.6.33+ Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Steve Dickson [Thu, 18 Sep 2014 13:13:17 +0000 (09:13 -0400)]
NFSv4: nfs4_state_manager() vs. nfs_server_remove_lists()
There is a race between nfs4_state_manager() and
nfs_server_remove_lists() that happens during a nfsv3 mount.
The v3 mount notices there is already a supper block so
nfs_server_remove_lists() called which uses the nfs_client_lock
spin lock to synchronize access to the client list.
At the same time nfs4_state_manager() is running through
the client list looking for work to do, using the same
lock. When nfs4_state_manager() wins the race to the
list, a v3 client pointer is found and not ignored
properly which causes the panic.
Moving some protocol checks before the state checking
avoids the panic.
CC: Stable Tree <stable@vger.kernel.org> Signed-off-by: Steve Dickson <steved@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
This commit is triggering failures to mount by subvolume id in some
configurations. The main problem is how many different ways this
scanning function is used, both for scanning while mounted and
unmounted. A proper cleanup is too big for late rcs.
For now, just revert the commit and we'll put a better fix into a later
merge window.
The original commit f2267089ea17fa97b796b1b4247e3f8957655df3
(usb: gadget: composite: dequeue cdev->req before free it in
composite_dev_cleanup) ended up being reverted because it caused
more issues then fixed. We will also revert this counter part
commit so we start clean to properly add that idea back.
Cc: Li Jun <b47624@freescale.com> Signed-of-by: Felipe Balbi <balbi@ti.com>
Ville Syrjälä [Fri, 12 Sep 2014 12:46:29 +0000 (15:46 +0300)]
drm/i915: Add limited color range readout for HDMI/DP ports on g4x/vlv/chv
The limited color range knob is in the port registers on
g4x and vlv/chv for HDMI, and on g4x for DP. Add the relevant code
to read out the hardware state into pipe config. On vlv/chv the
DP port limited color range knob is in PIPECONF for which we
already have readout code.
Cc: Chris Clayton <chris2553@googlemail.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Chris Clayton <chris2553@googlemail.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Joern Engel [Tue, 2 Sep 2014 21:49:54 +0000 (17:49 -0400)]
iscsi-target: avoid NULL pointer in iscsi_copy_param_list failure
In iscsi_copy_param_list() a failed iscsi_param_list memory allocation
currently invokes iscsi_release_param_list() to cleanup, and will promptly
trigger a NULL pointer dereference.
Instead, go ahead and return for the first iscsi_copy_param_list()
failure case.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org> Cc: <stable@vger.kernel.org> # v3.1+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
iscsi-target: Fix memory corruption in iscsit_logout_post_handler_diffcid
This patch fixes a bug in iscsit_logout_post_handler_diffcid() where
a pointer used as storage for list_for_each_entry() was incorrectly
being used to determine if no matching entry had been found.
This patch changes iscsit_logout_post_handler_diffcid() to key off
bool conn_found to determine if the function needs to exit early.
Reported-by: Joern Engel <joern@logfs.org> Cc: <stable@vger.kernel.org> # v3.1+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target: Fix inverted logic in SE_DEV_ALUA_SUPPORT_STATE_STORE
Fix inverted logic in SE_DEV_ALUA_SUPPORT_STATE_STORE for setting
the supported ALUA access states via configfs, originally introduced
in commit b0a382c5.
A value of 1 should enable the support, not disable it.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de> Cc: <stable@vger.kernel.org> # v3.14+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Here we move the rootdelay code to be right beside the rootwait code, so
that their behaviour is consistent.
...which is fine, but in hindsight, perhaps moving the rootwait to be
beside the rootdelay would have been better. We also indicated:
It should be noted that in doing so, the actions based on the
saved_root_name[0] and initrd_load() were previously put on hold by
rootdelay=N and now currently will not be delayed. However, I think
consistent behaviour is more important than matching historical behaviour
of delaying the above two operations.
But Pavel reported an instance where an ARM target with root on MMC
was failing to mount root, and Russell diagnosed it to the fact that
the call to set ROOT_DEV within the saved_root_name[0] processing
block mentioned above was no longer being delayed.
Rather than moving both wait clauses to the original position of
rootdelay and risking unearthing other possible corner case breakage
at this point in time, we simply revert now and we can revisit
trying the alternate/earlier location in another development cycle.
Cc: Pavel Machek <pavel@denx.de> Cc: Russell King <linux@arm.linux.org.uk> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kernel code overrides the default ISA as passed by the compiler
in quite a few places. This has unfortunate side effects when smartmips
is enabled leading to hundreds of warnings during build such as:
{standard input}: Assembler messages:
{standard input}:411: Warning: the `smartmips' extension requires MIPS32
revision 1 or greater
{standard input}: Assembler messages:
{standard input}:43: Warning: the 64-bit MIPS architecture does not support the
`smartmips' extension
[...]
Until the kernel code is fixed properly (if possible), disable all the
assembler warning messages to make the build logs readable again.
This has no runtime side effects but it makes it easier to spot
more critical warnings and problems during build.
Filipe Manana [Thu, 11 Sep 2014 20:22:14 +0000 (21:22 +0100)]
Btrfs: set inode's logged_trans/last_log_commit after ranged fsync
When a ranged fsync finishes if there are still extent maps in the modified
list, still set the inode's logged_trans and last_log_commit. This is important
in case an inode is fsync'ed and unlinked in the same transaction, to ensure its
inode ref gets deleted from the log and the respective dentries in its parent
are deleted too from the log (if the parent directory was fsync'ed in the same
transaction).
Instead make btrfs_inode_in_log() return false if the list of modified extent
maps isn't empty.
This is an incremental on top of the v4 version of the patch:
"Btrfs: fix fsync data loss after a ranged fsync"
which was added to its v5, but didn't make it on time.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com>
Bruno Prémont [Sun, 24 Aug 2014 21:13:15 +0000 (23:13 +0200)]
vgaarb: Drop obsolete #ifndef
Commit 20cde694027e ("x86, ia64: Move EFI_FB vga_default_device()
initialization to pci_vga_fixup()") moved boot video device detection from
efifb to x86 and ia64 pci/fixup.c.
Remove the left-over #ifndef check that will always match since the
corresponding arch-specific define is gone with above patch.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: Matthew Garrett <matthew.garrett@nebula.com>
projects / linux-beck.git / log