The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Laurent Navet [Mon, 13 May 2013 15:27:51 +0000 (17:27 +0200)]
drivers: net: can: grcan: use devm_ioremap_resource()
Replace a call to deprecated devm_request_and_ioremap by devm_ioremap_resource.
dev_err() message is no more needed since it's already displayed in
devm_ioremap_resource().
Signed-off-by: Laurent Navet <laurent.navet@gmail.com> Acked-by: Andreas Larsson <andreas@gaisler.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pull networking fixes from David Miller:
"Several small bug fixes all over:
1) be2net driver uses wrong payload length when submitting MAC list
get requests to the chip. From Sathya Perla.
2) Fix mwifiex memory leak on driver unload, from Amitkumar Karwar.
3) Prevent random memory access in batman-adv, from Marek Lindner.
4) batman-adv doesn't check for pskb_trim_rcsum() errors, also from
Marek Lindner.
5) Fix fec crashes on rapid link up/down, from Frank Li.
6) Fix inner protocol grovelling in GSO, from Pravin B Shelar.
7) Link event validation fix in qlcnic from Rajesh Borundia.
8) Not all FEC chips can support checksum offload, fix from Shawn
Guo.
9) EXPORT_SYMBOL + inline doesn't make any sense, from Denis Efremov.
10) Fix race in passthru mode during device removal in macvlan, from
Jiri Pirko.
11) Fix RCU hash table lookup socket state race in ipv6, leading to
NULL pointer derefs, from Eric Dumazet.
12) Add several missing HAS_DMA kconfig dependencies, from Geert
Uyttterhoeven.
13) Fix bogus PCI resource management in 3c59x driver, from Sergei
Shtylyov.
14) Fix info leak in ipv6 GRE tunnel driver, from Amerigo Wang.
15) Fix device leak in ipv6 IPSEC policy layer, from Cong Wang.
16) DMA mapping leak fix in qlge from Thadeu Lima de Souza Cascardo.
17) Missing iounmap on probe failure in bna driver, from Wei Yongjun."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
bna: add missing iounmap() on error in bnad_init()
qlge: fix dma map leak when the last chunk is not allocated
xfrm6: release dev before returning error
ipv6,gre: do not leak info to user-space
virtio_net: use default napi weight by default
emac: Fix EMAC soft reset on 460EX/GT
3c59x: fix PCI resource management
caif: CAIF_VIRTIO should depend on HAS_DMA
net/ethernet: MACB should depend on HAS_DMA
net/ethernet: ARM_AT91_ETHER should depend on HAS_DMA
net/wireless: ATH9K should depend on HAS_DMA
net/ethernet: STMMAC_ETH should depend on HAS_DMA
net/ethernet: NET_CALXEDA_XGMAC should depend on HAS_DMA
ipv6: do not clear pinet6 field
macvlan: fix passthru mode race between dev removal and rx path
ipv4: ip_output: remove inline marking of EXPORT_SYMBOL functions
net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode
net/mlx4_core: Add missing report on VST and spoof-checking dev caps
net: fec: enable hardware checksum only on imx6q-fec
qlcnic: Fix validation of link event command.
...
Wei Yongjun [Mon, 13 May 2013 04:26:06 +0000 (04:26 +0000)]
bna: add missing iounmap() on error in bnad_init()
Add the missing iounmap() before return from bnad_init()
in the error handling case.
Introduced by commit 01b54b1451853593739816a392485c4e2bee7dda
(bna: tx rx cleanup fix).
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
qlge: fix dma map leak when the last chunk is not allocated
qlge allocates chunks from a page that it maps and unmaps that page when
the last chunk is released. When the driver is unloaded or the card is
removed, all chunks are released and the page is unmapped for the last
chunk.
However, when the last chunk of a page is not allocated and the device
is removed, that page is not unmapped. In fact, its last reference is
not put and there's also a page leak. This bug prevents a device from
being properly hotplugged.
When the DMA API debug option is enabled, the following messages show
the pending DMA allocation after we remove the driver.
This patch fixes the bug by unmapping and putting the page from the ring
if its last chunk has not been allocated.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Acked-by: Jitendra Kalsaria <Jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 13 May 2013 15:12:18 +0000 (08:12 -0700)]
Merge tag 'spi-v3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A few driver specific fixes plus improved error handling in the
generic DT GPIO chipselect handling - not exciting but useful."
* tag 'spi-v3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi/spi-atmel: BUG: fix doesn' support 16 bits transfers using PIO
spi/davinci: fix module build error
spi: Return error from of_spi_register_master on bad "cs-gpios" property
spi: Initialize cs_gpio and cs_gpios with -ENOENT
spi/atmel: fix speed_hz check in atmel_spi_transfer()
Linus Torvalds [Mon, 13 May 2013 14:59:59 +0000 (07:59 -0700)]
Merge branch 'drm-next' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Just a few straggling fixes I hoovered up, and an intel fixes pull
from Daniel which fixes some regressions, and some mgag200 fixes from
Matrox."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux:
drm/mgag200: Fix framebuffer base address programming
drm/mgag200: Convert counter delays to jiffies
drm/mgag200: Fix writes into MGA1064_PIX_CLK_CTL register
drm/mgag200: Don't change unrelated registers during modeset
drm: Only print a debug message when the polled connector has changed
drm: Make the HPD status updates debug logs more readable
drm: Use names of ioctls in debug traces
drm: Remove pointless '-' characters from drm_fb_helper documentation
drm: Add kernel-doc for drm_fb_helper_funcs->initial_config
drm: refactor call to request_module
drm: Don't prune modes loudly when a connector is disconnected
drm: Add missing break in the command line mode parsing code
drm/i915: clear the stolen fb before resuming
Revert "drm/i915: Calculate correct stolen size for GEN7+"
drm/i915: hsw: fix link training for eDP on port-A
Revert "drm/i915: revert eDP bpp clamping code changes"
drm: don't check modeset locks in panic handler
drm/i915: Fix pipe enabled mask for pipe C in WM calculations
drm/mm: fix dump table BUG
drm/i915: Always normalize return timeout for wait_timeout_ioctl
Linus Torvalds [Mon, 13 May 2013 14:59:08 +0000 (07:59 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio/lguest fixes from Rusty Russell:
"Missing license tag and some fallout from the lguest pagetable rework"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
lguest: clear cached last cpu when guest_set_pgd() called.
Add missing module license tag to vring helpers.
drm/mgag200: Fix framebuffer base address programming
Higher bits of the base address of framebuffers weren't being
programmed properly. This caused framebuffers that didn't happen to be
allocated at a low enough address to not be displayed properly.
Signed-off-by: Christopher Harvey <charvey@matrox.com> Signed-off-by: Mathieu Larouche <mathieu.larouche@matrox.com> Acked-by: Julia Lemire <jlemire@matrox.com> Tested-by: Julia Lemire <jlemire@matrox.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Christopher Harvey <charvey@matrox.com> Acked-by: Julia Lemire <jlemire@matrox.com> Tested-by: Julia Lemire <jlemire@matrox.com> Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
drm/mgag200: Fix writes into MGA1064_PIX_CLK_CTL register
The original line,
WREG_DAC(MGA1064_PIX_CLK_CTL_CLK_DIS, tmp);
wrote tmp into MGA1064_PIX_CLK_CTL_CLK_DIS, where
MGA1064_PIX_CLK_CTL_CLK_DIS is an offset into
MGA1064_PIX_CLK_CTL. Change the line to write properly into
MGA1064_PIX_CLK_CTL. There were other chunks of code nearby that use
the same pattern (but work correctly), so this patch updates them all
to use this new (slightly more efficient) write pattern. The WREG_DAC
macro was causing the DAC_INDEX register to be set to the same value
twice. WREG8(DAC_DATA, foo) takes advantage of the fact that DAC_INDEX
is already at the value we want.
Signed-off-by: Christopher Harvey <charvey@matrox.com> Acked-by: Julia Lemire <jlemire@matrox.com> Tested-by: Julia Lemire <jlemire@matrox.com> Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
drm/mgag200: Don't change unrelated registers during modeset
Registers in indices below 0x18 are totally unrelated to modesetting,
so don't write 0's, or anything else into them on modeset. Most of
these registers are hardware cursor related, so this existing code
interferes with hardware cursor development.
Signed-off-by: Christopher Harvey <charvey@matrox.com> Tested-by: Julia Lemire <jlemire@matrox.com> Acked-by: Julia Lemire <jlemire@matrox.com> Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Lespiau, Damien [Fri, 10 May 2013 12:36:44 +0000 (12:36 +0000)]
drm: Only print a debug message when the polled connector has changed
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Cong Wang [Thu, 9 May 2013 22:40:00 +0000 (22:40 +0000)]
xfrm6: release dev before returning error
We forget to call dev_put() on error path in xfrm6_fill_dst(),
its caller doesn't handle this.
Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amerigo Wang [Thu, 9 May 2013 19:50:51 +0000 (19:50 +0000)]
virtio_net: use default napi weight by default
Since commit 82dc3c63c692b1e1d5937 ("net: introduce NAPI_POLL_WEIGHT")
we warn drivers when they use napi weight higher than NAPI_POLL_WEIGHT,
but virtio_net still uses 128 by default. This patch makes its default
value to NAPI_POLL_WEIGHT.
Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petri Gynther [Thu, 9 May 2013 16:50:00 +0000 (16:50 +0000)]
emac: Fix EMAC soft reset on 460EX/GT
Fix EMAC soft reset on 460EX/GT to select the right PHY clock source
before and after the soft reset.
EMAC with PHY should use the clock from PHY during soft reset.
EMAC without PHY should use the internal clock during soft reset.
PPC460EX/GT Embedded Processor Advanced User's Manual
section 28.10.1 Mode Register 0 (EMACx_MR0) states:
Note: The PHY must provide a TX Clk in order to perform a soft reset
of the EMAC. If none is present, select the internal clock
(SDR0_ETH_CFG[EMACx_PHY_CLK] = 1).
After a soft reset, select the external clock.
Without the fix, 460EX/GT-based boards with RGMII PHYs attached to
EMACs experience EMAC interrupt storm and system watchdog reset when
issuing "ifconfig eth0 down" + "ifconfig eth0 up" a few times.
The system enters endless loop of serving emac_irq() with EMACx_ISR
register stuck at value 0x10000000 (Rx parity error).
With the fix, the above issue is no longer observed.
Signed-off-by: Petri Gynther <pgynther@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Thu, 9 May 2013 11:14:07 +0000 (11:14 +0000)]
3c59x: fix PCI resource management
The driver wrongly claimed I/O ports at an address returned by pci_iomap() --
even if it was passed an MMIO address. Fix this by claiming/releasing all PCI
resources in the PCI driver's probe()/remove() methods instead and get rid of
'must_free_region' flag weirdness (why would Cardbus claim anything for us?).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 12 May 2013 00:04:59 +0000 (17:04 -0700)]
Merge tag 'trace-fixes-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing/kprobes update from Steven Rostedt:
"The majority of these changes are from Masami Hiramatsu bringing
kprobes up to par with the latest changes to ftrace (multi buffering
and the new function probes).
He also discovered and fixed some bugs in doing so. When pulling in
his patches, I also found a few minor bugs as well and fixed them.
This also includes a compile fix for some archs that select the ring
buffer but not tracing.
I based this off of the last patch you took from me that fixed the
merge conflict error, as that was the commit that had all the changes
I needed for this set of changes."
* tag 'trace-fixes-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/kprobes: Support soft-mode disabling
tracing/kprobes: Support ftrace_event_file base multibuffer
tracing/kprobes: Pass trace_probe directly from dispatcher
tracing/kprobes: Increment probe hit-count even if it is used by perf
tracing/kprobes: Use bool for retprobe checker
ftrace: Fix function probe when more than one probe is added
ftrace: Fix the output of enabled_functions debug file
ftrace: Fix locking in register_ftrace_function_probe()
tracing: Add helper function trace_create_new_event() to remove duplicate code
tracing: Modify soft-mode only if there's no other referrer
tracing: Indicate enabled soft-mode in enable file
tracing/kprobes: Fix to increment return event probe hit-count
ftrace: Cleanup regex_lock and ftrace_lock around hash updating
ftrace, kprobes: Fix a deadlock on ftrace_regex_lock
ftrace: Have ftrace_regex_write() return either read or error
tracing: Return error if register_ftrace_function_probe() fails for event_enable_func()
tracing: Don't succeed if event_enable_func did not register anything
ring-buffer: Select IRQ_WORK
drivers/built-in.o: In function `cfv_destroy_genpool':
drivers/net/caif/caif_virtio.c:364: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `cfv_create_genpool':
drivers/net/caif/caif_virtio.c:397: undefined reference to `dma_alloc_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/built-in.o: In function `macb_free_consistent':
drivers/net/ethernet/cadence/macb.c:878: undefined reference to `dma_free_coherent'
drivers/net/ethernet/cadence/macb.c:883: undefined reference to `dma_free_coherent'
drivers/net/ethernet/cadence/macb.c:888: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `macb_alloc_consistent':
drivers/net/ethernet/cadence/macb.c:905: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `macb_tx_interrupt':
drivers/net/ethernet/cadence/macb.c:515: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `macb_tx_error_task':
drivers/net/ethernet/cadence/macb.c:457: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `macb_start_xmit':
drivers/net/ethernet/cadence/macb.c:838: undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/ethernet: ARM_AT91_ETHER should depend on HAS_DMA
If NO_DMA=y:
drivers/built-in.o: In function `at91ether_start':
drivers/net/ethernet/cadence/at91_ether.c:49: undefined reference to `dma_alloc_coherent'
drivers/net/ethernet/cadence/at91_ether.c:60: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `at91ether_interrupt':
drivers/net/ethernet/cadence/at91_ether.c:250: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `at91ether_start_xmit':
drivers/net/ethernet/cadence/at91_ether.c:169: undefined reference to `dma_map_single'
drivers/built-in.o: In function `at91ether_close':
drivers/net/ethernet/cadence/at91_ether.c:145: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/built-in.o: In function `ath9k_beacon_generate':
drivers/net/wireless/ath/ath9k/beacon.c:146: undefined reference to `dma_unmap_single'
drivers/net/wireless/ath/ath9k/beacon.c:174: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/beacon.c:176: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath9k_beacon_remove_slot':
drivers/net/wireless/ath/ath9k/beacon.c:252: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_descdma_setup':
drivers/net/wireless/ath/ath9k/init.c:382: undefined reference to `dmam_alloc_coherent'
drivers/built-in.o: In function `ath_edma_get_buffers':
drivers/net/wireless/ath/ath9k/recv.c:616: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_get_next_rx_buf':
drivers/net/wireless/ath/ath9k/recv.c:740: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_rx_edma_cleanup':
drivers/net/wireless/ath/ath9k/recv.c:176: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_cleanup':
drivers/net/wireless/ath/ath9k/recv.c:340: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_edma_buf_link':
drivers/net/wireless/ath/ath9k/recv.c:122: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_rx_tasklet':
drivers/net/wireless/ath/ath9k/recv.c:1275: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:1277: undefined reference to `dma_mapping_error'
drivers/net/wireless/ath/ath9k/recv.c:1283: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_edma_init':
drivers/net/wireless/ath/ath9k/recv.c:226: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:229: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath_rx_init':
drivers/net/wireless/ath/ath9k/recv.c:303: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:306: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath_tx_complete_buf':
drivers/net/wireless/ath/ath9k/xmit.c:2088: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_txstatus_setup':
drivers/net/wireless/ath/ath9k/xmit.c:2344: undefined reference to `dmam_alloc_coherent'
drivers/built-in.o: In function `ath_tx_set_retry':
drivers/net/wireless/ath/ath9k/xmit.c:307: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_tx_setup_buffer':
drivers/net/wireless/ath/ath9k/xmit.c:1887: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/xmit.c:1889: undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/built-in.o: In function `dma_free_tx_skbufs':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1141: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `dma_free_rx_skbufs':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1120: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `free_dma_desc_resources':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1159: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `stmmac_init_rx_buffers':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:980: undefined reference to `dma_map_single'
drivers/built-in.o: In function `init_dma_desc_rings':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1015: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `stmmac_tx_clean':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1250: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `stmmac_rx':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2044: undefined reference to `dma_unmap_single'
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2082: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `stmmac_rx_refill':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1967: undefined reference to `dma_map_single'
drivers/built-in.o: In function `stmmac_xmit':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1845: undefined reference to `dma_map_single'
drivers/built-in.o: In function `skb_frag_dma_map':
include/linux/skbuff.h:2184: undefined reference to `dma_map_page'
drivers/built-in.o: In function `stmmac_jumbo_frm':
drivers/net/ethernet/stmicro/stmmac/ring_mode.c:40: undefined reference to `dma_map_single'
drivers/built-in.o: In function `stmmac_jumbo_frm':
drivers/net/ethernet/stmicro/stmmac/chain_mode.c:48: undefined reference to `dma_map_single'
drivers/net/ethernet/stmicro/stmmac/chain_mode.c:55: undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
net/ethernet: NET_CALXEDA_XGMAC should depend on HAS_DMA
If NO_DMA=y:
drivers/built-in.o: In function `xgmac_xmit':
drivers/net/ethernet/calxeda/xgmac.c:1102: undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Rob Herring <rob.herring@calxeda.com> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
I'm using following script to trigger this:
<script>
while [ 1 ]
do
ip link add link e1 name macvtap0 type macvtap mode passthru
ip link set e1 up
ip link set macvtap0 up
IFINDEX=`ip link |grep macvtap0 | cut -f 1 -d ':'`
cat /dev/tap$IFINDEX >/dev/null &
ip link del dev macvtap0
done
</script>
I run this script while "ping -f" is running on another machine to send
packets to e1 rx.
Reason of the panic is that list_first_entry() is blindly called in
macvlan_handle_frame() even if the list was empty. vlan is set to
incorrect pointer which leads to the crash.
I'm fixing this by protecting port->vlans list by rcu and by preventing
from getting incorrect pointer in case the list is empty.
Introduced by: commit eb06acdc85585f2 "macvlan: Introduce 'passthru' mode to takeover the underlying device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 11 May 2013 23:23:44 +0000 (16:23 -0700)]
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- fix parsing of user typed protocol string to avoid random memory access in
some cases
- check pskb_trim_rcsum() return value
- prevent DAT from sending ARP replies when not needed
- reorder the main clean up routine to prevent race conditions
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 11 May 2013 23:19:30 +0000 (16:19 -0700)]
Merge tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
- More fixes in the vCPU PVHVM hotplug path.
- Add more documentation.
- Fix various ARM related issues in the Xen generic drivers.
- Updates in the xen-pciback driver per Bjorn's updates.
- Mask the x2APIC feature for PV guests.
* tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: Used cached MSI-X capability offset
xen/pci: Use PCI_MSIX_TABLE_BIR, not PCI_MSIX_FLAGS_BIRMASK
xen: clear IRQ_NOAUTOEN and IRQ_NOREQUEST
xen: mask x2APIC feature in PV
xen: SWIOTLB is only used on x86
xen/spinlock: Fix check from greater than to be also be greater or equal to.
xen/smp/pvhvm: Don't point per_cpu(xen_vpcu, 33 and larger) to shared_info
xen/vcpu: Document the xen_vcpu_info and xen_vcpu
xen/vcpu/pvhvm: Fix vcpu hotplugging hanging.
Rony Efraim [Wed, 8 May 2013 22:22:35 +0000 (22:22 +0000)]
net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode
Make sure that the following steps are taken:
- drop packets sent by the VF with vlan tag
- block packets with vlan tag which are steered to the VF
- drop/block tagged packets when the policy is priority-tagged
- make sure VLAN stripping for received packets is set
- make sure force UP bit for the VF QP is set
Use enum values for all the above instead of numerical bit offsets.
Signed-off-by: Rony Efraim <ronye@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Wed, 8 May 2013 22:22:34 +0000 (22:22 +0000)]
net/mlx4_core: Add missing report on VST and spoof-checking dev caps
Commits e6b6a23 "net/mlx4: Add VF MAC spoof checking support" and 3f7fb021 "net/mlx4: Add set VF default vlan ID and priority support"
missed reporting in the device capabilities dump when these features
are actually supported. Also two too noisy debug messages which produce
message on every QP opened by a VF, were left in the code, fix that.
Signed-off-by: Rony Efraim <ronye@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shawn Guo [Wed, 8 May 2013 21:08:22 +0000 (21:08 +0000)]
net: fec: enable hardware checksum only on imx6q-fec
Commit 4c09eed (net: fec: Enable imx6 enet checksum acceleration.)
enables hardware checksum acceleration unconditionally for all fec
variants. This is inappropriate, because some variants like imx5 have
no such support on hardware. Consequently, fec is broken on these
platforms. Fix it by enabling hardware checksum only on imx6q-fec type
of controllers.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Jim Baxter <jim_baxter@mentor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 11 May 2013 23:01:23 +0000 (16:01 -0700)]
Merge branch 'qlcnic'
Shahed Shaikh says:
====================
This patch series has following bug fixes:
* Fix a bug in unicast MAC address setting in adapter.
Driver was not deleting older unicast MAC while adding new one.
* Fix an ethtool stats string array by adding missing string entry
and fix a typo.
* Fix module paramter description. Bracket ')' was missing.
* Fix port status provided though 'ethtool <device>' for 83xx adapter.
* Fix reset recovery path in case of transmit timeout.
* Fix reset recovery during diagnostic tests by preserving
current device status information.
* Fix mailbox response handling. Driver was not maintaining poll time properly.
* Fix validation of link event command.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rajesh Borundia [Thu, 9 May 2013 09:25:15 +0000 (09:25 +0000)]
qlcnic: Fix mailbox response handling.
o Fix mailbox response poll time to maximum 5 seconds which
includes mailbox response time as well as time required for
processing AEN if any.
o Driver need to read firmware control mailbox register instead
of host control mailbox register.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Thu, 9 May 2013 09:25:14 +0000 (09:25 +0000)]
qlcnic: Fix bug in diagnostics test reset recovery path
o In order to perform reset recovery during diagnostics tests,
current device status information need to be preserved.
This patch makes the required changes in diagnostics routines
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sony Chacko [Thu, 9 May 2013 09:25:13 +0000 (09:25 +0000)]
qlcnic: Fix reset recovery after transmit timeout
o When transmit timeout happens, recovery attempt should start with
adapter soft reset. If soft reset fails to resume traffic, firmware
dump will be collected and driver will perform a hard reset of the
adapter. Reset recovery on 83xx was failing after a hard reset.
This patch fixes that issue.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic: Fix ethtool supported port status for 83xx
o Fix display for interface while using 'ethtool <device>' for 83xx adapter
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Thu, 9 May 2013 09:25:09 +0000 (09:25 +0000)]
qlcnic: Fix setting MAC address
o Delete previous unicast MAC which is already programmed
in adapter before setting new unicast MAC
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 11 May 2013 22:24:22 +0000 (15:24 -0700)]
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull second SCSI update from James "Jaj B" Bottomley:
"This is the final round of SCSI patches for the merge window. It
consists mostly of driver updates (bnx2fc, ibmfc, fnic, lpfc,
be2iscsi, pm80xx, qla4x and ipr).
There's also the power management updates that complete the patches in
Jens' tree, an iscsi refcounting problem fix from the last pull, some
dif handling in scsi_debug fixes, a few nice code cleanups and an
error handling busy bug fix."
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (92 commits)
[SCSI] qla2xxx: Update firmware link in Kconfig file.
[SCSI] iscsi class, qla4xxx: fix sess/conn refcounting when find fns are used
[SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type
[SCSI] pm80xx: thermal, sas controller config and error handling update
[SCSI] pm80xx: NCQ error handling changes
[SCSI] pm80xx: WWN Modification for PM8081/88/89 controllers
[SCSI] pm80xx: Changed module name and debug messages update
[SCSI] pm80xx: Firmware flash memory free fix, with addition of new memory region for it
[SCSI] pm80xx: SPC new firmware changes for device id 0x8081 alone
[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files
[SCSI] pm80xx: MSI-X implementation for using 64 interrupts
[SCSI] pm80xx: Updated common functions common for SPC and SPCv/ve
[SCSI] pm80xx: Multiple inbound/outbound queue configuration
[SCSI] pm80xx: Added SPCv/ve specific ids, variables and modify for SPC
[SCSI] lpfc: fix up Kconfig dependencies
[SCSI] Handle MLQUEUE busy response in scsi_send_eh_cmnd
[SCSI] sd: change to auto suspend mode
[SCSI] sd: use REQ_PM in sd's runtime suspend operation
[SCSI] qla4xxx: Fix iocb_cnt calculation in qla4xxx_send_mbox_iocb()
[SCSI] ufs: Correct the expected data transfersize
...
Linus Torvalds [Sat, 11 May 2013 21:29:11 +0000 (14:29 -0700)]
Merge git://git.infradead.org/users/eparis/audit
Pull audit changes from Eric Paris:
"Al used to send pull requests every couple of years but he told me to
just start pushing them to you directly.
Our touching outside of core audit code is pretty straight forward. A
couple of interface changes which hit net/. A simple argument bug
calling audit functions in namei.c and the removal of some assembly
branch prediction code on ppc"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: fix message spacing printing auid
Revert "audit: move kaudit thread start from auditd registration to kaudit init"
audit: vfs: fix audit_inode call in O_CREAT case of do_last
audit: Make testing for a valid loginuid explicit.
audit: fix event coverage of AUDIT_ANOM_LINK
audit: use spin_lock in audit_receive_msg to process tty logging
audit: do not needlessly take a lock in tty_audit_exit
audit: do not needlessly take a spinlock in copy_signal
audit: add an option to control logging of passwords with pam_tty_audit
audit: use spin_lock_irqsave/restore in audit tty code
helper for some session id stuff
audit: use a consistent audit helper to log lsm information
audit: push loginuid and sessionid processing down
audit: stop pushing loginid, uid, sessionid as arguments
audit: remove the old depricated kernel interface
audit: make validity checking generic
audit: allow checking the type of audit message in the user filter
audit: fix build break when AUDIT_DEBUG == 2
audit: remove duplicate export of audit_enabled
Audit: do not print error when LSMs disabled
...
David S. Miller [Fri, 10 May 2013 16:44:05 +0000 (09:44 -0700)]
Merge branch 'wireless'
John W. Linville says:
====================
Here is a batch of fixes intended for the 3.10 stream.
Amitkumar Karwar provides an mwifiex fix to plug a memory leak when
the driver is unloaded.
Bing Zhao brings an mwifiex fix for some flag handling that leads to
log spam and an unusable interface.
Daniel Drake offers an mwifiex fix for multicast filter setup, to
correctly implement wakeup behaviour for multicast WOL.
Felix Fietkau fixes an ath9k problem that produces logspam and keycache
errors due to a bad return code.
Stanislaw Gruszka produces an fix for a WARNING from ath5k, and an
iwl4965 workaround to stop advertising a feature that doesn't work with
the current mac80211 implementation.
Sujith Manoharan gives us an ath9k fix to reprogram the HW beacon timers
after a TSF update, and an initvals fix for the AR9565 device.
Thommy Jakobsson fixes an rx descriptor underrun on b43.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 10 May 2013 16:27:40 +0000 (09:27 -0700)]
Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86
Pull x86 platform drivers from Matthew Garrett:
"Small set of updates, mainly trivial bugfixes and some small updates
to deal with newer hardware.
There's also a new driver that allows qemu guests to notify the
hypervisor that they've just paniced, which seems useful."
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
Add support for fan button on Ideapad Z580
pvpanic: pvpanic device driver
asus-nb-wmi: set wapf=4 for ASUSTeK COMPUTER INC. X75A
drivers: platform: x86: Use PTR_RET function
sony-laptop: SVS151290S kbd backlight and gfx switch support
hp-wmi: add more definitions for new event_id's
dell-laptop: Fix krealloc() misuse in parse_da_table()
hp_accel: Ignore the error from lis3lv02d_poweron() at resume
dell: add new dell WMI format for the AIO machines
Linus Torvalds [Fri, 10 May 2013 16:21:05 +0000 (09:21 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal
Pull stray syscall bits from Al Viro:
"Several syscall-related commits that were missing from the original"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
switch compat_sys_sysctl to COMPAT_SYSCALL_DEFINE
unicore32: just use mmap_pgoff()...
unify compat fanotify_mark(2), switch to COMPAT_SYSCALL_DEFINE
x86, vm86: fix VM86 syscalls: use SYSCALL_DEFINEx(...)
Linus Torvalds [Fri, 10 May 2013 16:20:01 +0000 (09:20 -0700)]
Merge tag 'ecryptfs-3.10-rc1-ablkcipher' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull eCryptfs update from Tyler Hicks:
"Improve performance when AES-NI (and most likely other crypto
accelerators) is available by moving to the ablkcipher crypto API.
The improvement is more apparent on faster storage devices.
There's no noticeable change when hardware crypto is not available"
* tag 'ecryptfs-3.10-rc1-ablkcipher' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: Use the ablkcipher crypto API
Linus Torvalds [Fri, 10 May 2013 16:09:47 +0000 (09:09 -0700)]
Merge tag 'for-linus-20130509' of git://git.infradead.org/~dwmw2/random-2.6
Pull misc fixes from David Woodhouse:
"This is some miscellaneous cleanups that don't really belong anywhere
else (or were ignored), that have been sitting in linux-next for some
time. Two of them are fixes resulting from my audit of krealloc()
usage that don't seem to have elicited any response when I posted
them, and the other three are patches from Artem removing dead code."
* tag 'for-linus-20130509' of git://git.infradead.org/~dwmw2/random-2.6:
pcmcia: remove RPX board stuff
m68k: remove rpxlite stuff
pcmcia: remove Motorola MBX860 support
params: Fix potential memory leak in add_sysfs_param()
dell-laptop: Fix krealloc() misuse in parse_da_table()
Linus Torvalds [Fri, 10 May 2013 16:08:21 +0000 (09:08 -0700)]
Merge tag 'kvm-3.10-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Gleb Natapov:
"Most of the fixes are in the emulator since now we emulate more than
we did before for correctness sake we see more bugs there, but there
is also an OOPS fixed and corruption of xcr0 register."
* tag 'kvm-3.10-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: emulator: emulate SALC
KVM: emulator: emulate XLAT
KVM: emulator: emulate AAM
KVM: VMX: fix halt emulation while emulating invalid guest sate
KVM: Fix kvm_irqfd_init initialization
KVM: x86: fix maintenance of guest/host xcr0 state
Linus Torvalds [Fri, 10 May 2013 16:02:50 +0000 (09:02 -0700)]
Merge tag 'dm-3.10-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper updates from Alasdair Kergon:
"Allow devices that hold metadata for the device-mapper thin
provisioning target to be extended easily; allow WRITE SAME on
multipath devices; an assortment of little fixes and clean-ups."
* tag 'dm-3.10-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: (21 commits)
dm cache: set config value
dm cache: move config fns
dm thin: generate event when metadata threshold passed
dm persistent metadata: add space map threshold callback
dm persistent data: add threshold callback to space map
dm thin: detect metadata device resizing
dm persistent data: support space map resizing
dm thin: open dev read only when possible
dm thin: refactor data dev resize
dm cache: replace memcpy with struct assignment
dm cache: fix typos in comments
dm cache policy: fix description of lookup fn
dm: document iterate_devices
dm persistent data: fix error message typos
dm cache: tune migration throttling
dm mpath: enable WRITE SAME support
dm table: fix write same support
dm bufio: avoid a possible __vmalloc deadlock
dm snapshot: fix error return code in snapshot_ctr
dm cache: fix error return code in cache_create
...
Linus Torvalds [Fri, 10 May 2013 16:00:39 +0000 (09:00 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fix usage of sleeping lock in atomic context from Jiri Kosina
- build fix for hid-steelseries under certain .config setups by Simon Wood
- simple mismerge fix from Fernando Luis Vázquez Cao
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: debug: fix RCU preemption issue
HID: hid-steelseries fix led class build issue
HID: reintroduce fix-up for certain Sony RF receivers
Linus Torvalds [Fri, 10 May 2013 14:51:56 +0000 (07:51 -0700)]
Merge tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains small fixes since the previous pull request:
- A few regression fixes and small updates of HD-audio
- Yet another fix for Haswell HDMI audio
- A copule of trivial fixes in ASoC McASP, DPAM and WM8994"
* tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
Revert "ALSA: hda - Don't set up active streams twice"
ALSA: Add comment for control TLV API
ALSA: hda - Apply pin-enablement workaround to all Haswell HDMI codecs
ALSA: HDA: Fix Oops caused by dereference NULL pointer
ALSA: mips/sgio2audio: Remove redundant platform_set_drvdata()
ALSA: mips/hal2: Remove redundant platform_set_drvdata()
ALSA: hda - Fix 3.9 regression of EAPD init on Conexant codecs
sound: Fix make allmodconfig on MIPS
ALSA: hda - Fix system panic when DMA > 40 bits for Nvidia audio controllers
ALSA: atmel: Remove redundant platform_set_drvdata()
ASoC: McASP: Fix receive clock polarity in DAIFMT_NB_NF mode.
ASoC: wm8994: missing break in wm8994_aif3_hw_params()
ASoC: McASP: Add pins output direction for rx clocks when configured in CBS_CFS format
ASoC: dapm: use clk_prepare_enable and clk_disable_unprepare
Linus Torvalds [Fri, 10 May 2013 14:48:05 +0000 (07:48 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
- More work on DT support for various platforms
- Various fixes that were to late to make it straight into 3.9
- Improved platform support, in particular the Netlogic XLR and
BCM63xx, and the SEAD3 and Malta eval boards.
- Support for several Ralink SOC families.
- Complete support for the microMIPS ASE which basically reencodes the
existing MIPS32/MIPS64 ISA to use non-constant size instructions.
- Some fallout from LTO work which remove old cruft and will generally
make the MIPS kernel easier to maintain and resistant to compiler
optimization, even in absence of LTO.
- KVM support. While MIPS has announced hardware virtualization
extensions this KVM extension uses trap and emulate mode for
virtualization of MIPS32. More KVM work to add support for VZ
hardware virtualizaiton extensions and MIPS64 will probably already
be merged for 3.11.
Most of this has been sitting in -next for a long time. All defconfigs
have been build or run time tested except three for which fixes are being
sent by other maintainers.
Semantic conflict with kvm updates done as per Ralf
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (118 commits)
MIPS: Add new GIC clockevent driver.
MIPS: Formatting clean-ups for clocksources.
MIPS: Refactor GIC clocksource code.
MIPS: Move 'gic_frequency' to common location.
MIPS: Move 'gic_present' to common location.
MIPS: MIPS16e: Add unaligned access support.
MIPS: MIPS16e: Support handling of delay slots.
MIPS: MIPS16e: Add instruction formats.
MIPS: microMIPS: Optimise 'strnlen' core library function.
MIPS: microMIPS: Optimise 'strlen' core library function.
MIPS: microMIPS: Optimise 'strncpy' core library function.
MIPS: microMIPS: Optimise 'memset' core library function.
MIPS: microMIPS: Add configuration option for microMIPS kernel.
MIPS: microMIPS: Disable LL/SC and fix linker bug.
MIPS: microMIPS: Add vdso support.
MIPS: microMIPS: Add unaligned access support.
MIPS: microMIPS: Support handling of delay slots.
MIPS: microMIPS: Add support for exception handling.
MIPS: microMIPS: Floating point support.
MIPS: microMIPS: Fix macro naming in micro-assembler.
...
Mike Christie [Mon, 6 May 2013 17:06:56 +0000 (12:06 -0500)]
[SCSI] iscsi class, qla4xxx: fix sess/conn refcounting when find fns are used
This fixes a bug where the iscsi class/driver did not do a put_device
when a sess/conn device was found. This also simplifies the interface
by not having to pass in some arguments that were duplicated and did
not need to be exported.
Reported-by: Zhao Hongjiang <zhaohongjiang@huawei.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Bottomley [Tue, 7 May 2013 21:44:06 +0000 (14:44 -0700)]
[SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type
These enums have been separate since the dawn of SAS, mainly because the
latter is a procotol only enum and the former includes additional state
for libsas. The dichotomy causes endless confusion about which one you
should use where and leads to pointless warnings like this:
drivers/scsi/mvsas/mv_sas.c: In function 'mvs_update_phyinfo':
drivers/scsi/mvsas/mv_sas.c:1162:34: warning: comparison between 'enum sas_device_type' and 'enum sas_dev_type' [-Wenum-compare]
Fix by eliminating one of them. The one kept is effectively the sas.h
one, but call it sas_device_type and make sure the enums are all
properly namespaced with the SAS_ prefix.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Tue, 19 Mar 2013 12:38:40 +0000 (18:08 +0530)]
[SCSI] pm80xx: thermal, sas controller config and error handling update
Modified thermal configuration to happen after interrupt registration
Added SAS controller configuration during initialization
Added error handling logic to handle I_T_Nexus errors and variants
[jejb: fix up tabs and spaces issues] Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Tue, 19 Mar 2013 12:38:08 +0000 (18:08 +0530)]
[SCSI] pm80xx: NCQ error handling changes
Handled NCQ errors in the low level driver as the FW
is not providing the faulty tag for NCQ errors for libsas
to recover.
[jejb: fix checkpatch issues] Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Tue, 19 Mar 2013 12:37:35 +0000 (18:07 +0530)]
[SCSI] pm80xx: WWN Modification for PM8081/88/89 controllers
Individual WWN read operations based on controller.
PM8081 - Read WWN from Flash VPD.
PM8088/89 - Read WWN from EEPROM.
PM8001 - Read WWN from NVM.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Tue, 19 Mar 2013 12:37:09 +0000 (18:07 +0530)]
[SCSI] pm80xx: Changed module name and debug messages update
Changed name in driver to pm80xx. Updated debug messages.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Tue, 19 Mar 2013 12:36:40 +0000 (18:06 +0530)]
[SCSI] pm80xx: Firmware flash memory free fix, with addition of new memory region for it
Performing pci_free_consistent in tasklet had result in a core dump. So
allocated a new memory region for it. Fix for passing proper address
and operation in firmware flash update.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Tue, 19 Mar 2013 12:35:55 +0000 (18:05 +0530)]
[SCSI] pm80xx: SPC new firmware changes for device id 0x8081 alone
Additional bar shift for new SPC firmware, applicable to device
id 0x8081 only.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Wed, 17 Apr 2013 11:07:02 +0000 (16:37 +0530)]
[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files
Implementation of SPCv/ve specific hardware functionality and
macros. Changing common functionalities wrt SPCv/ve operations.
Conditional checks for SPC specific operations.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Tue, 19 Mar 2013 12:26:17 +0000 (17:56 +0530)]
[SCSI] pm80xx: MSI-X implementation for using 64 interrupts
Implementation of interrupt handlers and tasklets to support
upto 64 interrupt for the device.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Wed, 27 Feb 2013 14:57:43 +0000 (20:27 +0530)]
[SCSI] pm80xx: Updated common functions common for SPC and SPCv/ve
Update of function prototype for common function to SPC and SPCv/ve.
Multiple queues implementation for IO.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Memory allocation and configuration of multiple inbound and
outbound queues.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Wed, 17 Apr 2013 10:56:36 +0000 (16:26 +0530)]
[SCSI] pm80xx: Added SPCv/ve specific ids, variables and modify for SPC
Updated pci id table with device, vendor, subdevice and subvendor ids
for 8081, 8088, 8089 SAS/SATA controllers. Added SPCv/ve related macros.
Updated macros, hba info structure and other structures for SPCv/ve.
Update of structure and variable names for SPC hardware functionalities.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hannes Reinecke [Thu, 25 Apr 2013 06:10:00 +0000 (08:10 +0200)]
[SCSI] Handle MLQUEUE busy response in scsi_send_eh_cmnd
scsi_send_eh_cmnd() is calling queuecommand() directly, so
it needs to check the return value here.
The only valid return codes for queuecommand() are 'busy'
states, so we need to wait for a bit to allow the LLDD
to recover.
Based on an earlier patch from Wen Xiong.
[jejb: fix confusion between msec and jiffies values and other issues]
[bvanassche: correct stall_for interval] Cc: Wen Xiong <wenxiong@linux.vnet.ibm.com> Cc: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Linus Torvalds [Fri, 10 May 2013 14:22:35 +0000 (07:22 -0700)]
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu updates from Greg Ungerer:
"The bulk of the changes are generalizing the ColdFire v3 core support
and adding in 537x CPU support. Also a couple of other bug fixes, one
to fix a reintroduction of a past bug in the romfs filesystem nommu
support."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: enable Timer on coldfire 532x
m68knommu: fix ColdFire 5373/5329 QSPI base address
m68knommu: add support for configuring a Freescale M5373EVB board
m68knommu: add support for the ColdFire 537x family of CPUs
m68knommu: make ColdFire M532x platform support more v3 generic
m68knommu: create and use a common M53xx ColdFire class of CPUs
m68k: remove unused asm/dbg.h
m68k: Set ColdFire ACR1 cache mode depending on kernel configuration
romfs: fix nommu map length to keep inside filesystem
m68k: clean up unused "config ROMVECSIZE"
Linus Torvalds [Fri, 10 May 2013 14:21:16 +0000 (07:21 -0700)]
Merge tag 'for-linus' of git://github.com/realmz/blackfin-linux
Pull blackfin updates from Steven Miao.
* tag 'for-linus' of git://github.com/realmz/blackfin-linux:
bfin cache: dcplb map: add 16M dcplb map for BF60x
blackfin: smp: fix smp build after drop asm/system.h
blackfin: fix bootup core clock and system clock display
Platform Nand: Set the GPIO for NAND read as input
blackfin: rename vmImage to uImage after we move to buildroot
blackfin: twi: Remove bogus #endif
bf609: rsi: Add bf609 rsi MMR macro and board platform data.
blackfin: dmc: Improve DDR2 write through in DMC effict controller.
Linus Torvalds [Fri, 10 May 2013 14:19:52 +0000 (07:19 -0700)]
Merge branch 'next' of git://git.monstr.eu/linux-2.6-microblaze
Pull microblaze updates from Michal Simek.
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Enable IRQ in arch_cpu_idle
microblaze: Fix uaccess_ok macro
microblaze: Add support for new cpu versions and target architecture
microblaze: Do not select OPT_LIB_ASM by default
microblaze: Fix initrd support
microblaze: Do not use r6 in head.S
microblaze: pci: Remove duplicated header
microblaze: Set the default irq_domain
microblaze: pci: Remove duplicated include from pci-common.c
Joe Thornber [Fri, 10 May 2013 13:37:20 +0000 (14:37 +0100)]
dm persistent data: add threshold callback to space map
Add a threshold callback function to the persistent data space map
interface for a subsequent patch to use.
dm-thin and dm-cache are interested in knowing when they're getting
low on metadata or data blocks. This patch introduces a new method
for registering a callback against a threshold.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Joe Thornber [Fri, 10 May 2013 13:37:19 +0000 (14:37 +0100)]
dm persistent data: support space map resizing
Support extending a dm persistent data metadata space map.
The extend itself is implemented by switching back to the boostrap
allocator and pointing to the new space. The extra bitmap indexes are
then allocated from the new space, and finally we switch back to the
proper space map ops and tweak the reference counts.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Joe Thornber [Fri, 10 May 2013 13:37:19 +0000 (14:37 +0100)]
dm thin: open dev read only when possible
If a thin pool is created in read-only-metadata mode then only open the
metadata device read-only.
Previously it was always opened with FMODE_READ | FMODE_WRITE.
(Note that dm_get_device() still allows read-only dm devices to be used
read-write at the moment: If I create a read-only linear device for the
metadata, via dmsetup load --readonly, then I can still create a rw pool
out of it.)
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
projects / linux-beck.git / log