Bruce Allan [Tue, 29 Nov 2011 08:09:19 +0000 (08:09 +0000)]
e1000e: hitting BUG_ON() from napi_enable
Based on a patch from Mike McElroy created against the out-of-tree e1000e
driver:
Hitting the BUG_ON in napi_enable(). Code inspection shows that this can
only be triggered by calling napi_enable() twice without an intervening
napi_disable().
I saw the following sequence of events in the stack trace:
1) We simulated a cable pull using an Extreme switch.
2) e1000_tx_timeout() was entered.
3) e1000_reset_task() was called. Saw the message from e_err() in the
console log.
4) e1000_reinit_locked was called. This function calls e1000_down() and
e1000_up(). These functions call napi_disable() and napi_enable()
respectively.
5) Then on another thread, a monitor task saw carrier was down and executed
'ip set link down' and 'ip set link up' commands.
6) Saw the '_E1000_RESETTING'warning fron the e1000_close function.
7) Either the e1000_open() executed between the e1000_down() and e1000_up()
calls in step 4 or the e1000_open() call executed after the e1000_up()
call. In either case, napi_enable() is called twice which triggers the
BUG_ON.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Cc: Mike McElroy <mike.mcelroy@stratus.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher [Fri, 18 Nov 2011 14:25:00 +0000 (14:25 +0000)]
e1000e: Avoid wrong check on TX hang
Based on the original patch submitted my Michael Wang
<wangyun@linux.vnet.ibm.com>.
Descriptors may not be write-back while checking TX hang with flag
FLAG2_DMA_BURST on.
So when we detect hang, we just flush the descriptor and detect
again for once.
-v2 change 1 to true and 0 to false and remove extra ()
CC: Michael Wang <wangyun@linux.vnet.ibm.com> CC: Flavio Leitner <fbl@redhat.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Igor Maravic [Thu, 1 Dec 2011 23:48:20 +0000 (23:48 +0000)]
forcedeath: Fix bql support for forcedeath
Moved netdev_completed_queue() out of while loop in function nv_tx_done_optimized().
Because this function was in while loop,
BUG_ON(count > dql->num_queued - dql->num_completed)
was hit in dql_completed().
Signed-off-by: Igor Maravic <igorm@etf.rs> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
netfilter: Remove ADVANCED dependency from NF_CONNTRACK_NETBIOS_NS
ipv4: flush route cache after change accept_local
sch_red: fix red_change
Revert "udp: remove redundant variable"
bridge: master device stuck in no-carrier state forever when in user-stp mode
ipv4: Perform peer validation on cached route lookup.
net/core: fix rollback handler in register_netdevice_notifier
sch_red: fix red_calc_qavg_from_idle_time
bonding: only use primary address for ARP
ipv4: fix lockdep splat in rt_cache_seq_show
sch_teql: fix lockdep splat
net: fec: Select the FEC driver by default for i.MX SoCs
isdn: avoid copying too long drvid
isdn: make sure strings are null terminated
netlabel: Fix build problems when IPv6 is not enabled
sctp: better integer overflow check in sctp_auth_create_key()
sctp: integer overflow in sctp_auth_create_key()
ipv6: Set mcast_hops to IPV6_DEFAULT_MCASTHOPS when -1 was given.
net: Fix corruption in /proc/*/net/dev_mcast
mac80211: fix race between the AGG SM and the Tx data path
...
Peter Pan(潘卫平) [Thu, 1 Dec 2011 15:47:06 +0000 (15:47 +0000)]
ipv4: flush route cache after change accept_local
After reset ipv4_devconf->data[IPV4_DEVCONF_ACCEPT_LOCAL] to 0,
we should flush route cache, or it will continue receive packets with local
source address, which should be dropped.
Signed-off-by: Weiping Pan <panweiping3@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 1 Dec 2011 11:06:34 +0000 (11:06 +0000)]
sch_red: fix red_change
Le mercredi 30 novembre 2011 à 14:36 -0800, Stephen Hemminger a écrit :
> (Almost) nobody uses RED because they can't figure it out.
> According to Wikipedia, VJ says that:
> "there are not one, but two bugs in classic RED."
RED is useful for high throughput routers, I doubt many linux machines
act as such devices.
I was considering adding Adaptative RED (Sally Floyd, Ramakrishna
Gummadi, Scott Shender), August 2001
In this version, maxp is dynamic (from 1% to 50%), and user only have to
setup min_th (target average queue size)
(max_th and wq (burst in linux RED) are automatically setup)
By the way it seems we have a small bug in red_change()
if (skb_queue_empty(&sch->q))
red_end_of_idle_period(&q->parms);
First, if queue is empty, we should call
red_start_of_idle_period(&q->parms);
Second, since we dont use anymore sch->q, but q->qdisc, the test is
meaningless.
Oh well...
[PATCH] sch_red: fix red_change()
Now RED is classful, we must check q->qdisc->q.qlen, and if queue is empty,
we start an idle period, not end it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 1 Dec 2011 22:55:34 +0000 (14:55 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: (31 commits)
ocfs2: avoid unaligned access to dqc_bitmap
ocfs2: Use filemap_write_and_wait() instead of write_inode_now()
ocfs2: honor O_(D)SYNC flag in fallocate
ocfs2: Add a missing journal credit in ocfs2_link_credits() -v2
ocfs2: send correct UUID to cleancache initialization
ocfs2: Commit transactions in error cases -v2
ocfs2: make direntry invalid when deleting it
fs/ocfs2/dlm/dlmlock.c: free kmem_cache_zalloc'd data using kmem_cache_free
ocfs2: Avoid livelock in ocfs2_readpage()
ocfs2: serialize unaligned aio
ocfs2: Implement llseek()
ocfs2: Fix ocfs2_page_mkwrite()
ocfs2: Add comment about orphan scanning
ocfs2: Clean up messages in the fs
ocfs2/cluster: Cluster up now includes network connections too
ocfs2/cluster: Add new function o2net_fill_node_map()
ocfs2/cluster: Fix output in file elapsed_time_in_ms
ocfs2/dlm: dlmlock_remote() needs to account for remastery
ocfs2/dlm: Take inflight reference count for remotely mastered resources too
ocfs2/dlm: Cleanup dlm_wait_for_node_death() and dlm_wait_for_node_recovery()
...
Akinobu Mita [Tue, 15 Nov 2011 22:56:34 +0000 (14:56 -0800)]
ocfs2: avoid unaligned access to dqc_bitmap
The dqc_bitmap field of struct ocfs2_local_disk_chunk is 32-bit aligned,
but not 64-bit aligned. The dqc_bitmap is accessed by ocfs2_set_bit(),
ocfs2_clear_bit(), ocfs2_test_bit(), or ocfs2_find_next_zero_bit(). These
are wrapper macros for ext2_*_bit() which need to take an unsigned long
aligned address (though some architectures are able to handle unaligned
address correctly)
So some 64bit architectures may not be able to access the dqc_bitmap
correctly.
This avoids such unaligned access by using another wrapper functions for
ext2_*_bit(). The code is taken from fs/ext4/mballoc.c which also need to
handle unaligned bitmap access.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Acked-by: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Joel Becker <jlbec@evilplan.org>
Linus Torvalds [Thu, 1 Dec 2011 19:53:54 +0000 (11:53 -0800)]
Merge branch 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7182/1: ARM cpu topology: fix warning
ARM: 7181/1: Restrict kprobes probing SWP instructions to ARMv5 and below
ARM: 7180/1: Change kprobes testcase with unpredictable STRD instruction
ARM: 7177/1: GIC: avoid skipping non-existent PPIs in irq_start calculation
ARM: 7176/1: cpu_pm: register GIC PM notifier only once
ARM: 7175/1: add subname parameter to mfp_set_groupg callers
ARM: 7174/1: Fix build error in kprobes test code on Thumb2 kernels
ARM: 7172/1: dma: Drop GFP_COMP for DMA memory allocations
ARM: 7171/1: unwind: add unwind directives to bitops assembly macros
ARM: 7170/2: fix compilation breakage in entry-armv.S
ARM: 7168/1: use cache type functions for arch_get_unmapped_area
ARM: perf: check that we have a platform device when reserving PMU
ARM: 7166/1: Use PMD_SHIFT instead of PGDIR_SHIFT in dma-consistent.c
ARM: 7165/2: PL330: Fix typo in _prepare_ccr()
ARM: 7163/2: PL330: Only register usable channels
ARM: 7162/1: errata: tidy up Kconfig options for PL310 errata workarounds
ARM: 7161/1: errata: no automatic store buffer drain
ARM: perf: initialise used_mask for fake PMU during validation
ARM: PMU: remove pmu_init declaration
ARM: PMU: re-export release_pmu symbol to modules
net/dccp/probe.c: In function ‘dccpprobe_init’:
net/dccp/probe.c:166:2: warning: the omitted middle operand in ?: will always be ‘true’, suggest explicit middle operand [-Wparentheses]
try_then_request_module() is built for situations where the
"existence" test is some lookup function that returns a non-NULL
object on success, and with a reference count of some kind held.
Here we're looking for a success return of zero from the jprobe
registry.
Instead of fighting the way try_then_request_module() works, simply
open code what we want to happen in a local helper function.
Signed-off-by: David S. Miller <davem@davemloft.net>
If we take the "try_again" goto, due to a checksum error,
the 'len' has already been truncated. So we won't compute
the same values as the original code did.
Reported-by: paul bilke <fsmail@conspiracy.net> Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: master device stuck in no-carrier state forever when in user-stp mode
When in user-stp mode, bridge master do not follow state of its slaves, so
after the following sequence of events it can stuck forever in no-carrier
state:
1) turn stp off
2) put all slaves down - master device will follow their state and also go in
no-carrier state
3) turn stp on with bridge-stp script returning 0 (go to the user-stp mode)
Now bridge master won't follow slaves' state and will never reach running
state.
This patch solves the problem by making user-stp and kernel-stp behavior
similar regarding master following slaves' states.
Signed-off-by: Vitalii Demianets <vitas@nppfactor.kiev.ua> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 30 Nov 2011 19:00:53 +0000 (19:00 +0000)]
ipv4: use a 64bit load/store in output path
gcc compiler is smart enough to use a single load/store if we
memcpy(dptr, sptr, 8) on x86_64, regardless of
CONFIG_CC_OPTIMIZE_FOR_SIZE
In IP header, daddr immediately follows saddr, this wont change in the
future. We only need to make sure our flowi4 (saddr,daddr) fields wont
break the rule.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
powerpc: tqm8548/tqm8xx: add and update CAN device nodes
This patch enables or updates support for the CC770 and AN82527
CAN controller on the TQM8548 and TQM8xx boards.
CC: devicetree-discuss@lists.ozlabs.org CC: linuxppc-dev@ozlabs.org CC: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
can: cc770: add platform bus driver for the CC770 and AN82527
This driver works with both, static platform data and device tree
bindings. It has been tested on a TQM855L board with two AN82527
CAN controllers on the local bus.
CC: Devicetree-discuss@lists.ozlabs.org CC: linuxppc-dev@ozlabs.org CC: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
can: cc770: add legacy ISA bus driver for the CC770 and AN82527
This patch adds support for legacy Bosch CC770 and Intel AN82527 CAN
controllers on the ISA or PC-104 bus. The I/O port or memory address
and the IRQ number must be specified via module parameters:
insmod cc770_isa.ko port=0x310,0x380 irq=7,11
for ISA devices using I/O ports or:
insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11
for memory mapped ISA devices.
Indirect access via address and data port is supported as well:
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
can: cc770: add driver core for the Bosch CC770 and Intel AN82527
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick Kelle [Thu, 1 Dec 2011 17:54:46 +0000 (12:54 -0500)]
icplus: mdio_write(), remove unnecessary for loop
At this point the variable j is always set to 7 and the code within
the loop has to run only once anyway.
As suggested by David Miller:
"You can simply this even further since p[7] is what is used here,
and this means len is one, the inner loop therefore executes only
once, and the p[7].field value is not used (it's zero in the table)
and the write to it is completely thrown away."
Signed-off-by: Patrick Kelle <patrick.kelle81@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Axel Lin [Wed, 30 Nov 2011 22:07:18 +0000 (22:07 +0000)]
dsa: Include linux/if_ether.h to fix build error
Include linux/if_ether.h to fix below build errors:
CC arch/arm/mach-kirkwood/common.o
In file included from arch/arm/mach-kirkwood/common.c:19:
include/net/dsa.h: In function 'dsa_uses_dsa_tags':
include/net/dsa.h:192: error: 'ETH_P_DSA' undeclared (first use in this function)
include/net/dsa.h:192: error: (Each undeclared identifier is reported only once
include/net/dsa.h:192: error: for each function it appears in.)
include/net/dsa.h: In function 'dsa_uses_trailer_tags':
include/net/dsa.h:197: error: 'ETH_P_TRAILER' undeclared (first use in this function)
make[1]: *** [arch/arm/mach-kirkwood/common.o] Error 1
make: *** [arch/arm/mach-kirkwood] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Hagen Paul Pfeifer <hagen@jauu.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 1 Dec 2011 16:28:53 +0000 (08:28 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix meta data raid-repair merge problem
Btrfs: skip allocation attempt from empty cluster
Btrfs: skip block groups without enough space for a cluster
Btrfs: start search for new cluster at the beginning
Btrfs: reset cluster's max_size when creating bitmap
Btrfs: initialize new bitmaps' list
Btrfs: fix oops when calling statfs on readonly device
Btrfs: Don't error on resizing FS to same size
Btrfs: fix deadlock on metadata reservation when evicting a inode
Fix URL of btrfs-progs git repository in docs
btrfs scrub: handle -ENOMEM from init_ipath()
Jan Schmidt [Thu, 1 Dec 2011 14:30:36 +0000 (09:30 -0500)]
Btrfs: fix meta data raid-repair merge problem
Commit 4a54c8c16 introduced raid-repair, killing the individual
readpage_io_failed_hook entries from inode.c and disk-io.c. Commit 4bb31e92 introduced new readahead code, adding a readpage_io_failed_hook to
disk-io.c.
The raid-repair commit had logic to disable raid-repair, if
readpage_io_failed_hook is set. Thus, the readahead commit effectively
disabled raid-repair for meta data.
This commit changes the logic to always attempt raid-repair when needed and
call the readpage_io_failed_hook in case raid-repair fails. This is much
more straight forward and should have been like that from the beginning.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net> Reported-by: Stefan Behrens <sbehrens@giantdisaster.de> Signed-off-by: Chris Mason <chris.mason@oracle.com>
RongQing.Li [Thu, 1 Dec 2011 04:43:07 +0000 (23:43 -0500)]
net/core: fix rollback handler in register_netdevice_notifier
Within nested statements, the break statement terminates only the
do, for, switch, or while statement that immediately encloses it,
So replace the break with goto.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 30 Nov 2011 12:10:53 +0000 (12:10 +0000)]
sch_red: fix red_calc_qavg_from_idle_time
Since commit a4a710c4a7490587 (pkt_sched: Change PSCHED_SHIFT from 10 to
6) it seems RED/GRED are broken.
red_calc_qavg_from_idle_time() computes a delay in us units, but this
delay is now 16 times bigger than real delay, so the final qavg result
smaller than expected.
Use standard kernel time services since there is no need to obfuscate
them.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netem is not in the ability to emulate channel bandwidth. Only static
delay (and optional random jitter) can be configured.
To emulate the channel rate the token bucket filter (sch_tbf) can be used. But
TBF has some major emulation flaws. The buffer (token bucket depth/rate) cannot
be 0. Also the idea behind TBF is that the credit (token in buckets) fills if
no packet is transmitted. So that there is always a "positive" credit for new
packets. In real life this behavior contradicts the law of nature where
nothing can travel faster as speed of light. E.g.: on an emulated 1000 byte/s
link a small IPv4/TCP SYN packet with ~50 byte require ~0.05 seconds - not 0
seconds.
Netem is an excellent place to implement a rate limiting feature: static
delay is already implemented, tfifo already has time information and the
user can skip TBF configuration completely.
This patch implement rate feature which can be configured via tc. e.g:
tc qdisc add dev eth0 root netem rate 10kbit
To emulate a link of 5000byte/s and add an additional static delay of 10ms:
Note: similar to TBF the rate extension is bounded to the kernel timing
system. Depending on the architecture timer granularity, higher rates (e.g.
10mbit/s and higher) tend to transmission bursts. Also note: further queues
living in network adaptors; see ethtool(8).
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@drr.davemloft.net>
Only use the primary address of the bond device
for master_ip. This will prevent changing the ARP source
address in Active-Backup mode whenever a secondry address
is added to the bond device.
Signed-off-by: Henrik Saavedra Persson <henrik.e.persson@ericsson.com> Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@drr.davemloft.net>
Linus Torvalds [Thu, 1 Dec 2011 00:24:24 +0000 (16:24 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: twl: fix twl4030 support for smps regulators
regulator: fix use after free bug
regulator: aat2870: Fix the logic of checking if no id is matched in aat2870_get_regulator
ARM: 7181/1: Restrict kprobes probing SWP instructions to ARMv5 and below
The SWP instruction is deprecated on ARMv6 and with ARMv7 it will be
UNDEFINED when CONFIG_SWP_EMULATE is selected. In this case, probing a
SWP instruction will cause an oops when the kprobes emulation code
executes an undefined instruction.
As the SWP instruction should be rare or non-existent in kernels for
ARMv6 and later, we can simply avoid these problems by not allowing
probing of these.
Reported-by: Leif Lindholm <leif.lindholm@arm.com> Tested-by: Leif Lindholm <leif.lindholm@arm.com> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Jon Medhurst <tixy@yxit.co.uk> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM: 7180/1: Change kprobes testcase with unpredictable STRD instruction
There is a kprobes testcase for the instruction "strd r2, [r3], r4".
This has unpredictable behaviour as it uses r3 for register writeback
addressing and also stores it to memory.
On a cortex A9, this testcase would fail because the instruction writes
the updated value of r3 to memory, whereas the kprobes emulation code
writes the original value.
Fix this by changing testcase to used r5 instead of r3.
Reported-by: Leif Lindholm <leif.lindholm@arm.com> Tested-by: Leif Lindholm <leif.lindholm@arm.com> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Jon Medhurst <tixy@yxit.co.uk> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
David Miller [Mon, 25 Jul 2011 00:01:22 +0000 (00:01 +0000)]
neigh: Get rid of neigh_table->kmem_cachep
We are going to alloc for device specific private areas for
neighbour entries, and in order to do that we have to move
away from the fixed allocation size enforced by using
neigh_table->kmem_cachep
As a nice side effect we can now use kfree_rcu().
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 29 Nov 2011 20:05:55 +0000 (20:05 +0000)]
ipv4: fix lockdep splat in rt_cache_seq_show
After commit f2c31e32b378 (fix NULL dereferences in check_peer_redir()),
dst_get_neighbour() should be guarded by rcu_read_lock() /
rcu_read_unlock() section.
Reported-by: Miles Lane <miles.lane@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 30 Nov 2011 01:02:41 +0000 (01:02 +0000)]
tcp: inherit listener congestion control for passive cnx
Rick Jones reported that TCP_CONGESTION sockopt performed on a listener
was ignored for its children sockets : right after accept() the
congestion control for new socket is the system default one.
This seems an oversight of the initial design (quoted from Stephen)
Based on prior investigation and patch from Rick.
Reported-by: Rick Jones <rick.jones2@hp.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Stephen Hemminger <shemminger@vyatta.com> CC: Yuchung Cheng <ycheng@google.com> Tested-by: Rick Jones <rick.jones2@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre Oliva [Wed, 30 Nov 2011 18:43:00 +0000 (13:43 -0500)]
Btrfs: skip block groups without enough space for a cluster
We test whether a block group has enough free space to hold the
requested block, but when we're doing clustered allocation, we can
save some cycles by testing whether it has enough room for the cluster
upfront, otherwise we end up attempting to set up a cluster and
failing. Only in the NO_EMPTY_SIZE loop do we attempt an unclustered
allocation, and by then we'll have zeroed the cluster size, so this
patch won't stop us from using the block group as a last resort.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Alexandre Oliva [Wed, 30 Nov 2011 18:43:00 +0000 (13:43 -0500)]
Btrfs: start search for new cluster at the beginning
Instead of starting at zero (offset is always zero), request a cluster
starting at search_start, that denotes the beginning of the current
block group.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Alexandre Oliva [Wed, 30 Nov 2011 18:43:00 +0000 (13:43 -0500)]
Btrfs: reset cluster's max_size when creating bitmap
The field that indicates the size of the largest contiguous chunk of
free space in the cluster is not initialized when setting up bitmaps,
it's only increased when we find a larger contiguous chunk. We end up
retaining a larger value than appropriate for highly-fragmented
clusters, which may cause pointless searches for large contiguous
groups, and even cause clusters that do not meet the density
requirements to be set up.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Alexandre Oliva [Mon, 28 Nov 2011 14:04:43 +0000 (12:04 -0200)]
Btrfs: initialize new bitmaps' list
We're failing to create clusters with bitmaps because
setup_cluster_no_bitmap checks that the list is empty before inserting
the bitmap entry in the list for setup_cluster_bitmap, but the list
field is only initialized when it is restored from the on-disk free
space cache, or when it is written out to disk.
Besides a potential race condition due to the multiple use of the list
field, filesystem performance severely degrades over time: as we use
up all non-bitmap free extents, the try-to-set-up-cluster dance is
done at every metadata block allocation. For every block group, we
fail to set up a cluster, and after failing on them all up to twice,
we fall back to the much slower unclustered allocation.
To make matters worse, before the unclustered allocation, we try to
create new block groups until we reach the 1% threshold, which
introduces additional bitmaps and thus block groups that we'll iterate
over at each metadata block request.
Mike Fleetwood [Fri, 18 Nov 2011 18:55:01 +0000 (18:55 +0000)]
Btrfs: Don't error on resizing FS to same size
It seems overly harsh to fail a resize of a btrfs file system to the
same size when a shrink or grow would succeed. User app GParted trips
over this error. Allow it by bypassing the shrink or grow operation.
Signed-off-by: Mike Fleetwood <mike.fleetwood@googlemail.com>
Miao Xie [Fri, 18 Nov 2011 09:43:00 +0000 (17:43 +0800)]
Btrfs: fix deadlock on metadata reservation when evicting a inode
When I ran the xfstests, I found the test tasks was blocked on meta-data
reservation.
By debugging, I found the reason of this bug:
start transaction
|
v
reserve meta-data space
|
v
flush delay allocation -> iput inode -> evict inode
^ |
| v
wait for delay allocation flush <- reserve meta-data space
And besides that, the flush on evicting inode will block the thread, which
is reclaiming the memory, and make oom happen easily.
Fix this bug by skipping the flush step when evicting inode.
Dmitry Kravkov [Mon, 28 Nov 2011 12:31:49 +0000 (12:31 +0000)]
bnx2x: handle iSCSI SD mode
in iSCSI SD mode to bnx2x device assigned single mac address
which is supposted to be iscsi mac. If this mode is recognized
bnx2x will disable LRO, decrease number of queues to 1 and rx ring
size to the minumum allowed by FW, this in order minimize memory use.
It will tranfer mac for iscsi usage and zero primary mac of the netdev.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for legacy Bosch CC770 and Intel AN82527 CAN
controllers on the ISA or PC-104 bus. The I/O port or memory address
and the IRQ number must be specified via module parameters:
insmod cc770_isa.ko port=0x310,0x380 irq=7,11
for ISA devices using I/O ports or:
insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11
for memory mapped ISA devices.
Indirect access via address and data port is supported as well:
Robert Marklund [Thu, 24 Nov 2011 01:03:07 +0000 (01:03 +0000)]
net/smsc911x: Add regulator support
Add some basic regulator support for the power pins, as needed
by the ST-Ericsson Snowball platform that powers up the SMSC911
chip using an external regulator.
Platforms that use regulators and the smsc911x and have no defined
regulator for the smsc911x and claim complete regulator
constraints with no dummy regulators will need to provide it, for
example using a fixed voltage regulator. It appears that this may
affect (apart from Ux500 Snowball) possibly these archs/machines
that from some grep:s appear to define both CONFIG_SMSC911X and
CONFIG_REGULATOR:
- ARM Freescale mx3 and OMAP 2 plus, Raumfeld machines
- Blackfin
- Super-H
Cc: Paul Mundt <lethal@linux-sh.org> Cc: linux-sh@vger.kernel.org Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Tony Lindgren <tony@atomide.com> Cc: linux-omap@vger.kernel.org Cc: Mike Frysinger <vapier@gentoo.org> Cc: uclinux-dist-devel@blackfin.uclinux.org Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Robert Marklund <robert.marklund@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
can: sja1000_isa: convert to platform driver to support x86_64 systems
This driver is currently not supported on x86_64 systems because the
"isa_driver" interface is used (CONFIG_ISA=y). To overcome this
limitation, the driver is converted to a platform driver, similar to
the serial 8250 driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the compiler warnings: "comparison is always
false due to limited range of data type" by using "0xff" instead
of "-1" for unsigned values.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 29 Nov 2011 22:43:22 +0000 (14:43 -0800)]
Merge branch 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Update comments describing device power management callbacks
PM / Sleep: Update documentation related to system wakeup
PM / Runtime: Make documentation follow the new behavior of irq_safe
PM / Sleep: Correct inaccurate information in devices.txt
PM / Domains: Document how PM domains are used by the PM core
PM / Hibernate: Do not leak memory in error/test code paths
Paul Moore [Tue, 29 Nov 2011 10:10:54 +0000 (10:10 +0000)]
netlabel: Fix build problems when IPv6 is not enabled
A recent fix to the the NetLabel code caused build problem with
configurations that did not have IPv6 enabled; see below:
netlabel_kapi.c: In function 'netlbl_cfg_unlbl_map_add':
netlabel_kapi.c:165:4:
error: implicit declaration of function 'netlbl_af6list_add'
This patch fixes this problem by making the IPv6 specific code conditional
on the IPv6 configuration flags as we done in the rest of NetLabel and the
network stack as a whole. We have to move some variable declarations
around as a result so things may not be quite as pretty, but at least it
builds cleanly now.
Some additional IPv6 conditionals were added to the NetLabel code as well
for the sake of consistency.
Reported-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Paul Moore <pmoore@redhat.com> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 29 Nov 2011 21:31:23 +0000 (22:31 +0100)]
IB: Fix RCU lockdep splats
Commit f2c31e32b37 ("net: fix NULL dereferences in check_peer_redir()")
forgot to take care of infiniband uses of dst neighbours.
Many thanks to Marc Aurele who provided a nice bug report and feedback.
Reported-by: Marc Aurele La France <tsi@ualberta.ca> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: David Miller <davem@davemloft.net> Cc: <stable@kernel.org> Signed-off-by: Roland Dreier <roland@purestorage.com>
The while loop at the bottom of ipoib_mcast_join_finish() will attempt
to send queued multicast packets in mcast->pkt_queue and eventually
end up in ipoib_mcast_send():
if (!mcast->ah) {
if (skb_queue_len(&mcast->pkt_queue) < IPOIB_MAX_MCAST_QUEUE)
skb_queue_tail(&mcast->pkt_queue, skb);
else {
++dev->stats.tx_dropped;
dev_kfree_skb_any(skb);
}
My read is that the code will requeue the packet and return to the
ipoib_mcast_join_finish() while loop and the stage is set for the
"hung" task diagnostic as the while loop never sees a non-NULL ah, and
will do nothing to resolve.
There are GFP_ATOMIC allocates in the provider routines, so this is
possible and should be dealt with.
The test that induced the failure is associated with a host SM on the
same server during a shutdown.
This patch causes ipoib_mcast_join_finish() to exit with an error
which will flush the queued mcast packets. Nothing is done to unwind
the QP attached state so that subsequent sends from above will retry
the join.
Reviewed-by: Ram Vepa <ram.vepa@qlogic.com> Reviewed-by: Gary Leshner <gary.leshner@qlogic.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Xi Wang [Tue, 29 Nov 2011 09:26:30 +0000 (09:26 +0000)]
sctp: better integer overflow check in sctp_auth_create_key()
The check from commit 30c2235c is incomplete and cannot prevent
cases like key_len = 0x80000000 (INT_MAX + 1). In that case, the
left-hand side of the check (INT_MAX - key_len), which is unsigned,
becomes 0xffffffff (UINT_MAX) and bypasses the check.
However this shouldn't be a security issue. The function is called
from the following two code paths:
1) setsockopt()
2) sctp_auth_asoc_set_secret()
In case (1), sca_keylength is never going to exceed 65535 since it's
bounded by a u16 from the user API. As such, the key length will
never overflow.
In case (2), sca_keylength is computed based on the user key (1 short)
and 2 * key_vector (3 shorts) for a total of 7 * USHRT_MAX, which still
will not overflow.
In other words, this overflow check is not really necessary. Just
make it more correct.
Signed-off-by: Xi Wang <xi.wang@gmail.com> Cc: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 29 Nov 2011 19:13:22 +0000 (11:13 -0800)]
Merge branch 'slab/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux
* 'slab/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
slub: avoid potential NULL dereference or corruption
slub: use irqsafe_cpu_cmpxchg for put_cpu_partial
slub: move discard_slab out of node lock
slub: use correct parameter to add a page to partial list tail
Eric Dumazet [Mon, 28 Nov 2011 22:41:47 +0000 (22:41 +0000)]
tcp: avoid frag allocation for small frames
tcp_sendmsg() uses select_size() helper to choose skb head size when a
new skb must be allocated.
If GSO is enabled for the socket, current strategy is to force all
payload data to be outside of headroom, in PAGE fragments.
This strategy is not welcome for small packets, wasting memory.
Experiments show that best results are obtained when using 2048 bytes
for skb head (This includes the skb overhead and various headers)
This patch provides better len/truesize ratios for packets sent to
loopback device, and reduce memory needs for in-flight loopback packets,
particularly on arches with big pages.
If a sender sends many 1-byte packets to an unresponsive application,
receiver rmem_alloc will grow faster and will stop queuing these packets
sooner, or will collapse its receive queue to free excess memory.
netperf -t TCP_RR results are improved by ~4 %, and many workloads are
improved as well (tbench, mysql...)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 28 Nov 2011 20:30:35 +0000 (20:30 +0000)]
flow_dissector: use a 64bit load/store
Le lundi 28 novembre 2011 à 19:06 -0500, David Miller a écrit :
> From: Dimitris Michailidis <dm@chelsio.com>
> Date: Mon, 28 Nov 2011 08:25:39 -0800
>
> >> +bool skb_flow_dissect(const struct sk_buff *skb, struct flow_keys
> >> *flow)
> >> +{
> >> + int poff, nhoff = skb_network_offset(skb);
> >> + u8 ip_proto;
> >> + u16 proto = skb->protocol;
> >
> > __be16 instead of u16 for proto?
>
> I'll take care of this when I apply these patches.
( CC trimmed )
Thanks David !
Here is a small patch to use one 64bit load/store on x86_64 instead of
two 32bit load/stores.
[PATCH net-next] flow_dissector: use a 64bit load/store
gcc compiler is smart enough to use a single load/store if we
memcpy(dptr, sptr, 8) on x86_64, regardless of
CONFIG_CC_OPTIMIZE_FOR_SIZE
In IP header, daddr immediately follows saddr, this wont change in the
future. We only need to make sure our flow_keys (src,dst) fields wont
break the rule.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mv-sheeva.git / log