Olof Johansson [Wed, 19 Apr 2017 13:48:32 +0000 (06:48 -0700)]
Merge tag 'omap-for-v4.12/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Second set of devicetree changes for omaps for v4.12 merge window
to configure various devices:
- Enable DCAN on am57xx-idk
- Enable CPSW ethernet0 and 1 on am335x-icev2
- Non-critical fix for droid 4 PMIC interrupt triggering
- Stop disabling SRAM and GPMC on droid 4
- Configure CPCAP PMIC related devices on droid 4 for ADC, charger
and USB PHY. The charger and USB PHY drivers are still being
discussed, but the binding for them has been acked by Rob and
Sebastian so they should be safe to merge together with the ADC
driver in Linux next that they depend on
Olof Johansson [Wed, 19 Apr 2017 13:45:59 +0000 (06:45 -0700)]
Merge tag 'imx-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX device tree updates for 4.12:
- New board support: I2SE's i.MX28 Duckbill-2 boards, Gateworks Ventana
i.MX6 GW5903/GW5904, Zodiac Inflight Innovations RDU2 board, Engicam
i.CoreM6 Quad/Dual OpenFrame modules, Boundary Device i.MX6 Quad Plus
SOM.
- Improve compatible string for i.MX50 eSDHC, i.MX7S SRC devices and
i.MX6SX UART device.
- Add interrupts for switch and PHY devices on VF610 ZII Devel C board.
- Add LVDS, LCD backlight, touchscreen and SAI2 support for i.MX6
icore, geam, and isiot boards.
- A series from Lucas Stach to improve i.MX6Q Plus device tree and add
PRE/PRG devices.
- A series from Stefan Agner to update imx7-colibri device tree
regarding to display, PMIC/regulator support.
- Fix PCI bus DTC warnings seen with the latest compiler.
- Set default phy_type and dr_mode for i.MX25 USBOTG port.
- A couple of small improvements on i.MX25 pin function DT header.
- Add audio support for imx6q-cm-fx6 board using Wolfson wm8731 codec
which is muxed to SSI2 device.
- Other random updates, small fixes and trivial cleanups.
* tag 'imx-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (56 commits)
ARM: dts: imx6q-utilite-pro: add hpd gpio
ARM: dts: imx6qp-sabresd: Set reg_arm regulator supply
ARM: dts: imx6qdl-sabresd: Set LDO regulator supply
ARM: dts: imx: add Gateworks Ventana GW5903 support
ARM: dts: i.MX25: add AIPS control registers
ARM: dts: imx7-colibri: add Carrier Board 3.3V/5V regulators
ARM: dts: imx7-colibri: remove 1.8V fixed regulator
ARM: dts: imx7-colibri: allow to disable Ethernet rail
ARM: dts: imx7-colibri: fix PMIC voltages
ARM: dts: imx7-colibri: use OF graph to describe the display
ARM: dts: imx6qp-nitrogen6_som2: add Quad Plus variant of the SOM
ARM: dts: imx6q-icore: Add touchscreen node
ARM: dts: vf610-zii-dev-rev-b: change switch2 label
ARM: dts: imx6ul-[geam|isiot]: Add sai2 node
ARM: dts: imx6ul-isiot-common: Add touchscreen node
ARM: dts: imx6ul-isiot: Add i2c nodes
ARM: dts: imx6ul-isiot: Add imx6ul-isiot-common.dtsi
ARM: dts: imx6ul-isiot: Add backlight support for lcdif
ARM: dts: imx6ul-geam: Add backlight support for lcdif
ARM: dts: imx6: add ZII RDU2 boards
...
Olof Johansson [Wed, 19 Apr 2017 13:45:10 +0000 (06:45 -0700)]
Merge tag 'v4.12-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Support for the usb-sata controller on the rock2 and another new rk3288
board, the phyCORE som and its PCM-947 carrier board from Phytec.
* tag 'v4.12-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add support for PCM-947 carrier board
dt-bindings: Document Phytec phyCORE-RK3288 RDK
ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM
ARM: dts: rockchip: Enable sata support on rock2 square
Olof Johansson [Wed, 19 Apr 2017 13:44:37 +0000 (06:44 -0700)]
Merge tag 'samsung-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DeviceTree ARM update for v4.12:
1. Enhancements to PCIe nodes on Exynos5440.
2. Fix thermal values on some of Exynos5420 boards like Odroid XU3.
3. Add proper clock frequency properties to DSI nodes.
4. Fix watchdog reset on Exynos4412.
5. Fix watchdog infinite interrupt in soft mode on Exynos4210,
Exynos5440, S3C64xx and S5Pv210.
6. Enable watchdog on Exynos4 and S3C SoCs.
* tag 'samsung-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: add HDMI controller phandle to exynos4.dtsi
ARM: dts: s5pv210: Fix infinite interrupt in soft mode
ARM: dts: s3c64xx: Fix infinite interrupt in soft mode
ARM: dts: exynos: Fix infinite interrupt in soft mode on Exynos4210 and Exynos5440
ARM: dts: exynos: Enable watchdog on all Exynos4 boards
ARM: dts: s3c64xx: Enable watchdog on all S3C64xx boards
ARM: dts: exynos: Fix watchdog reset on Exynos4412
ARM: dts: exynos: Add the burst and esc clock frequency properties to DSI node
ARM: dts: exynos: Do not ignore real-world fuse values for thermal zone 0 on Exynos5420
ARM: dts: exynos: Add phy-pcie node for pcie to Exynos5440
Olof Johansson [Wed, 19 Apr 2017 13:43:54 +0000 (06:43 -0700)]
Merge tag 'mvebu-dt-4.12-2' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.12 (part 2)
Use disk-activity trigger for armada-385-linksys
Keep dts alphabetically ordered for clearfog (Armada 388)
* tag 'mvebu-dt-4.12-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-385-linksys: disk-activity trigger for all
ARM: dts: clearfog: keep dts alphabetically ordered
Olof Johansson [Wed, 19 Apr 2017 13:43:08 +0000 (06:43 -0700)]
Merge tag 'renesas-dt2-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM Based SoC DT Updates for v4.12
Corrections:
* Correct clock frequency of X2 DU clock input for r8a7791/koelsch board
* Correct Z clock for r8a7792 SoC
* Correct parent of SSI[0-9] clocks for r8a779[013] SoCs
* Correct ethernet clock parent on r7s72100 SoC
* Correct DU clock for r8a7794/silk board
Cleanups:
* Drop _clk suffix from external CAN clock node name on r8a779[01] SoCs
Enhancements:
* Enable rtc r7s72100/genmai board
* Add Z2 clock for r8a7794 SoC
* Add DU clock for r8a7794 SoC
* Add power-domains to SDHI for r8a7794 and r7s72100 SoCs
* Add reset control properties for r8a774[35] SoCs
* tag 'renesas-dt2-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (22 commits)
ARM: dts: r8a7791: Drop _clk suffix from external CAN clock node name
ARM: dts: r8a7790: Drop _clk suffix from external CAN clock node name
ARM: dts: genmai: Enable rtc and rtc_x1 clock
ARM: dts: rskrza1: add rtc DT support
ARM: dts: rskrza1: set rtc_x1 clock value
ARM: dts: r7s72100: add rtc to device tree
ARM: dts: r7s72100: add RTC_X clock inputs to device tree
ARM: dts: r7s72100: add rtc clock to device tree
ARM: dts: koelsch: Correct clock frequency of X2 DU clock input
ARM: dts: r8a7794: Add Z2 clock
ARM: dts: r8a7792: Correct Z clock
ARM: dts: r8a7793: Correct parent of SSI[0-9] clocks
ARM: dts: r8a7791: Correct parent of SSI[0-9] clocks
ARM: dts: r8a7790: Correct parent of SSI[0-9] clocks
ARM: dts: r7s72100: fix ethernet clock parent
ARM: dts: silk: Correct clock of DU1
ARM: dts: alt: Correct clock of DU1
ARM: dts: r8a7794: Correct clock of DU1
ARM: dts: r8a7794: Add DU1 clock to device tree
ARM: dts: r7s72100: add power-domains to sdhi
...
Olof Johansson [Wed, 19 Apr 2017 13:42:08 +0000 (06:42 -0700)]
Merge tag 'qcom-dts-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt
Qualcomm Device Tree Changes for v4.12
* Add Coresight components for MSM8974
* Fixup MSM8974 ADSP XO clk and add RPMCC node
* Fix typo in APQ8060
* Add SDCs on MSM8660
* Revert MSM8974 USB gadget change due to issues
* tag 'qcom-dts-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
Revert "ARM: dts: qcom: msm8974: Add USB gadget nodes"
ARM: dts: qcom: msm8974: Add RPMCC DT node
ARM: dts: fix typo on APQ8060 Dragonboard
ARM: dts: add SDC2 and SDC4 to the MSM8660 family
ARM: dts: msm8974: Hook up adsp-pil's xo clock
ARM: dts: qcom: Add msm8974 CoreSight components
Olof Johansson [Wed, 19 Apr 2017 13:28:42 +0000 (06:28 -0700)]
Merge tag 'tegra-for-4.12-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
dt-bindings: Updates for v4.12-rc1
This contains an update for the flow controller device tree binding as
well as the addition of the binding for the GP10B GPU found on the new
Tegra186 (Parker) SoC.
* tag 'tegra-for-4.12-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: Add documentation for GP10B GPU
dt-bindings: tegra: Update compatible strings for Tegra flowctrl
Olof Johansson [Wed, 19 Apr 2017 12:39:05 +0000 (05:39 -0700)]
Merge tag 'sunxi-dt-h3-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner H3 DT changes for 4.12
H3 patches for 4.12, which are mostly related to reworking the H3 DTSI to
be usable on the arm64 H5 DTSI, that shares almost everything with the H3
but the CPU cores.
We also have some new device addition (USB, mostly) that would conflict
otherwise.
* tag 'sunxi-dt-h3-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: sun8i: h2+: enable USB OTG for Orange Pi Zero board
ARM: sun8i: h3: enable USB OTG on Orange Pi One
ARM: sunxi: h3/h5: add usb_otg and OHCI/EHCI for usbc0 on H3/H5
arm: sun8i: h3: split Allwinner H3 .dtsi
arm: sun8i: h3: correct the GIC compatible in H3 to gic-400
arm: sun8i: h3: drop pinctrl-a10.h inclusion for H3 DTSI
arm: sun8i: h3: drop skeleton.dtsi inclusion in H3 DTSI
Olof Johansson [Wed, 19 Apr 2017 12:37:06 +0000 (05:37 -0700)]
Merge tag 'sunxi-dt-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.12
As usual a number of changes, among which:
- All the sun5i DTSI has been reworked based on the new documentation and
the IPs that are actually found in all those SoCs. Part of that rework
also brought the GR8 DTSI to include sun5i.dtsi
- Mali devfreq and thermal throttling support on the A33
- AC power supplies for the AXP209 and AXP22X PMIC
- CAN support for the A20
- CPUFreq-based thermal throttling for the A33
- New board: NanoPi NEO Air
* tag 'sunxi-dt-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (38 commits)
ARM: sun8i: sina33: add highest OPP of CPUs
ARM: sun8i: a33: Add devfreq-based GPU cooling
ARM: sun8i: a33: add CPU thermal throttling
ARM: sun8i: a33: add thermal sensor
ARM: dts: sun7i: fix device node ordering
ARM: dts: sun4i: fix device node ordering
ARM: dts: sun7i: Add can0_pins_a pinctrl settings
ARM: dts: sun7i: Add CAN node
ARM: dts: sun4i: Add can0_pins_a pinctrl settings
ARM: dts: sun4i: Add CAN node
ARM: sun7i: cubietruck: enable ACIN und USB power supply subnode
ARM: dts: sun5i: Add interrupt for display backend
dt-bindings: display: sun4i: Add display backend interrupt to device tree binding
ARM: dts: sun7i: Use axp209.dtsi on A20-OLinuXino-Micro
ARM: dts: sun6i: sina31s: Enable SPDIF out
ARM: sun8i: sina33: add cpu-supply
ARM: sun8i: a33: add all operating points
ARM: sun5i: chip: enable ACIN power supply subnode
ARM: dts: sun8i: sina33: enable ACIN power supply subnode
ARM: dtsi: axp22x: add AC power supply subnode
...
Olof Johansson [Wed, 19 Apr 2017 12:31:20 +0000 (05:31 -0700)]
Merge tag 'socfpga_dts_for_v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS updates for v4.12
- Clean-up:
- Add clock/memory nodes
- Add labels for CPU nodes
- Remove unused unit names and reg
- Remove unused skeleton.dtsi
- Add support for PMU
- Add QSPI for sodia board
- Add Reset controller for Arria10
* tag 'socfpga_dts_for_v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: Add Devkit A10-SR Reset Controller
ARM: dts: socfpga: sodia: enable qspi
ARM: dts: socfpga: Add support for PMU
ARM: dts: socfpga: Add labels for CPU nodes
ARM: dts: socfpga: Do not include skeleton.dtsi
ARM: dts: socfpga: Remove unit name for LEDs in EBV SOCrates
ARM: dts: socfpga: Remove unneeded reg from stmpe_touchscreen
ARM: dts: socfpga: Remove unneeded unit names
ARM: dts: socfpga: Add unit name to memory nodes
ARM: dts: socfpga: Add unit name to clock nodes
Olof Johansson [Wed, 19 Apr 2017 12:22:29 +0000 (05:22 -0700)]
Merge tag 'stm32-dt-for-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into next/dt
STM32 DT updates for v4.12, round 1
Highlights:
----------
- ADD RTC support on STM32F746 MCU
- Enable RTC on STM32F746 Eval board
- Enable clocks on STM32F746 MCU
- Enable DMA, pwm1 and pwm3 on STM32F429I Eval
- Add support of STM32H743 MCU and his Eval board
- Enable USB HS and FS on STM32F469 Disco board
* tag 'stm32-dt-for-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
dt-bindings: Document the STM32 USB OTG DWC2 core binding
ARM: dts: stm32: Enable USB HS in FS mode (embedded phy) on stm32f429-disco
ARM: dts: stm32: Enable USB FS on stm32f469-disco
ARM: dts: stm32: Add USB FS support for STM32F429 MCU
ARM: dts: stm32: Add STM32H743 MCU and STM32H743i-EVAL board
ARM: dts: stm32: Enable pwm1 and pwm3 on stm32f429i-eval
ARM: dts: stm32: Enable dma by default on stm32f4 adc
ARM: dts: stm32: enable RTC on stm32746g-eval
ARM: dts: stm32: Add RTC support for STM32F746 MCU
ARM: dts: stm32: set HSE_RTC clock frequency to 1 MHz on stm32f746
dt-bindings: mfd: Add STM32F7 RCC numeric constants into DT include file
ARM: dts: stm32: Enable clocks for STM32F746 MCU
Tim Harvey [Mon, 3 Apr 2017 21:18:21 +0000 (14:18 -0700)]
ARM: dts: imx: add Gateworks Ventana GW5903 support
The Gateworks Ventana GW5903 is a single-board computer based on the NXP
IMX6 SoC with the following features:
* IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
* 4GiB DDR3 DRAM
* 32GB eMMC
* 1x microSD connector
* Gateworks System Controller:
- hardware watchdog
- hardware monitor
- pushbutton controller
- EEPROM storage
- power control
* JTAG programmable
* Inertial Module
* uBlox EMMY-W1 (bluetooth/nfc/802.11ac)
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Martin Kaiser [Mon, 3 Apr 2017 19:47:04 +0000 (21:47 +0200)]
ARM: dts: i.MX25: add AIPS control registers
The i.MX25 contains two AHB to IP bridges (AIPS), each of which has a set of
control registers. Add the memory regions for the control registers to
the Device Tree.
Signed-off-by: Martin Kaiser <martin@kaiser.cx> Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Model the Carrier Board power distribution by adding a fixed 3.3V
and 5V regulator. The 3.3V regulator is connected to the backlight
as well as the display supply. The 5V regulator is used to supply
USB VBUS.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Wed, 29 Mar 2017 23:21:11 +0000 (16:21 -0700)]
ARM: dts: imx7-colibri: allow to disable Ethernet rail
The regulator-always-on property on the Ethernet rail prevents Linux
from disabling the rail when Ethernet is shut down (suspend or simply
link down). With this change the regulator framework will disable the
rail when the Ethernet PHY is not used, saving power especially on
carrier board not using Ethernet.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Wed, 29 Mar 2017 23:21:10 +0000 (16:21 -0700)]
ARM: dts: imx7-colibri: fix PMIC voltages
Fix wrong voltage of PWR_EN_+V3.3 rail. The error had no noticeable
effect since no consumer explicitly requested a specific voltage.
Also use round voltages as it is common in other device trees.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename the switch2@0 label of the switch2 node to switch@0 to respect
the general unit@address DTS rule, and be consistent with the other
switch nodes of the DTS file.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add touchscreen node as i2c1 slave device on Engicam Is.IoT MX6UL
modules, the touchscreen controlled 'st,stmpe-ts' connected via
i2c with st,stmpe811 mfd interface.
Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
lcdif nodes are differ wrt specific LCD connected on Is.IoT MX6UL
module, so create separate file 'imx6ul-isiot-common.dtsi' for common
lcdif node structure and include the same on respective dts.
More common nodes will add in future patches.
Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Uwe Kleine-König [Mon, 20 Mar 2017 08:21:11 +0000 (09:21 +0100)]
ARM: dts: imx25-pinfunc: Move MX25_PAD_TDO__TDO to a more sensible place
The pinfunc definitions are ordered by mux_reg and so automatically by
conf_reg, too. PAD_TDO is the only pad that has a conf_reg but no
mux_reg. Put it to the place where it its in the order of conf_regs
instead of the top.
Andrey Smirnov [Tue, 14 Mar 2017 15:33:57 +0000 (08:33 -0700)]
ARM: dts: imx7s: Do not claim i.MX51 compatibility for SRC
System Reset Controller in i.MX7 doesn't have any commonality with IP
block found in i.MX5 and i.MX6 SoC families. Given that and the new
upstream driver for i.MX7 variant (see
https://lkml.org/lkml/2017/2/21/466) remove "fsl,imx51-src" from
compatibility string.
Cc: yurovsky@gmail.com Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Russell King <linux@armlinux.org.uk> Cc: devicetree@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jagan Teki [Tue, 14 Mar 2017 09:48:12 +0000 (15:18 +0530)]
ARM: dts: imx6q: Add Engicam i.CoreM6 Quad/Dual OpenFrame Cap 12.3 initial support
i.CoreM6 Quad/Dual OpenFrame modules are "system on modules plus
openframe display carriers" which are good solution for develop
user friendly graphic user interface.
General features:
CPU NXP i.MX6Q rev1.2 at 792 MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
LVDS Display TFT 12.3" industrial, 1280x480 resolution
Backlight LED backlight, brightness 350 Cd/m2
Power supply 15 to 30 Vdc
Cc: Domenico Acri <domenico.acri@engicam.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jagan Teki [Tue, 14 Mar 2017 09:48:11 +0000 (15:18 +0530)]
ARM: dts: imx6q: Add Engicam i.CoreM6 Quad/Dual OpenFrame Cap 10.1 initial support
i.CoreM6 Quad/Dual OpenFrame modules are "system on modules plus
openframe display carriers" which are good solution for develop
user friendly graphic user interface.
General features:
CPU NXP i.MX6Q rev1.2 at 792 MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
LVDS Display TFT 10.1" industrial, 1280x800 resolution
Backlight LED backlight, brightness 350 Cd/m2
Power supply 15 to 30 Vdc
Cc: Domenico Acri <domenico.acri@engicam.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrew Lunn [Wed, 8 Mar 2017 02:50:13 +0000 (03:50 +0100)]
ARM: dts: vf610-zii-dev-c: Wire up PHY interrupts
The PHYs embedded in the switch direct there interrupts through the
switch interrupt controllers. Now that devel C has its switch
interrupts connected to the SoC, the PHY interrupts can be used by
phylib. Explicitly include MDIO nodes in the switch device tree nodes,
and link the PHY interrupts back to the switch interrupt
controller. Also, link the ports to the PHYs on the MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrew Lunn [Wed, 8 Mar 2017 02:50:12 +0000 (03:50 +0100)]
ARM: dts: vf610-zii-dev: Wire up devel C switch interrupts
The devel B and devel C board use the same GPIO lines for interrupts
from the two switches. Move the pinmux nodes from devel B into the
shared .dtsi file, and wire up the interrupts on devel C.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Kurz [Thu, 2 Mar 2017 21:03:48 +0000 (22:03 +0100)]
ARM: dts: imx50: imx50-esdhc use imx53-esdhc
According to the reference manuals, both imx50/imx53 SOC seem to share
the same eSDHC controller, especially the section on "Multi-block Read"
mentioned in commit 361b8482026c ("mmc: sdhci-esdhc-imx: fix multiblock
reads on i.MX53") is identical for both SOC.
Hence, let imx50 use imx53-esdhc.
Signed-off-by: Alexander Kurz <akurz@blala.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lucas Stach [Fri, 17 Feb 2017 13:48:36 +0000 (14:48 +0100)]
ARM: dts: imx6qp: reference MMDC node by handle and remove duplication
Referencing the node by handle make the QP DT more resilent against
changes of the base DT. Also remove the duplicated reg property, it's
not needed as it the same as in the base DT, just the compatible is
actually different.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Uwe Kleine-König [Thu, 16 Feb 2017 21:18:58 +0000 (22:18 +0100)]
ARM: imx25: set default phy_type and dr_mode for usbotg port
All currently supported i.MX25-based machines use phy_type = "utmi" and
dr_mode = "otg". So this seems to be a sensible default.
This also doesn't hurt out-of-tree machines because up to now they had
to specify these two properties in the machine.dts which still takes
precedence by just overwriting the defaults added here.
This machine is based on I2SE's Duckbill 2 board and is sold as part
of I2SE's PLC Bundle for IoT. This is a development kit for Homeplug
Green PHY based powerline products based on Qualcomms QCA7000 chip.
Signed-off-by: Michael Heimpold <mhei@heimpold.de> Cc: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This machine is based on I2SE's Duckbill 2 board and features a
EnOcean daugther board based on the popular TCM310 chipset.
This product is intended to be used for e.g. home automation purposes.
Signed-off-by: Michael Heimpold <mhei@heimpold.de> Cc: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This machine is based on I2SE's Duckbill 2 board and features a
RS-485 daugther board. This device is intended to be used for
e.g. home automation purposes.
Signed-off-by: Michael Heimpold <mhei@heimpold.de> Cc: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This machine is an USB pen drive sized development board,
based on NXP's i.MX28 CPU. In contrast to the previous
model "Duckbill", the "Duckbill 2" series has internal
eMMC storage.
Signed-off-by: Michael Heimpold <mhei@heimpold.de> Cc: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Cc: devicetree@vger.kernel.org Cc: Marcel Partap <mpartap@gmx.net> Cc: Michael Scott <michael.scott@linaro.org> Reviewed-by: Sebastian Reichel <sre@kernel.org> Tested-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: devicetree@vger.kernel.org Cc: Marcel Partap <mpartap@gmx.net> Cc: Michael Scott <michael.scott@linaro.org> Reviewed-by: Sebastian Reichel <sre@kernel.org> Tested-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: devicetree@vger.kernel.org Cc: Marcel Partap <mpartap@gmx.net> Cc: Michael Scott <michael.scott@linaro.org> Reviewed-by: Sebastian Reichel <sre@kernel.org> Tested-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
The string was changed when upstreaming the driver. Put the correct
string for generation 4 and 5 systems, as well as fix the reg length for
ast2500 systems.
Acked-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au>
Joel Stanley [Thu, 6 Apr 2017 01:41:43 +0000 (11:11 +0930)]
ARM: dts: aspeed: Make G4 clocks fixed
We do not yet have a clk driver upstream. So that users can boot the
unmodified upstream kernel, add fixed-clock and clock-frequency
properties to all of the clocks.
The values are taken from the Palmetto system. This is the only upstream
dts. It also happens to match all of the systems seen so far.
Acked-by: Cédric Le Goater <clg@kaod.org> Acked-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au>
Joel Stanley [Fri, 31 Mar 2017 02:35:10 +0000 (13:05 +1030)]
ARM: dts: aspeed: Make G5 clocks fixed
We do not yet have a clk driver upstream. So that users can boot the
unmodified upstream kernel, add fixed-clock and clock-frequency
properties to all of the clocks.
The values are taken from the ast2500evb. This is the only upstream dts.
It also happens to match all of the systems I have seen so far.
Acked-by: Cédric Le Goater <clg@kaod.org> Acked-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au>
This change caused issues with people using USB gadget for serial
consoles. In addition, with the other USB changes coming in, it
makes sense to revert this patch and apply the new set as it
becomes ready.
ARM: dts: rockchip: Add support for PCM-947 carrier board
Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.
Following interfaces and devices are available on the PCM-947 carrier board:
- 2x UART
- micro SDMMC
- USB host and USB otg
- USB 3503 HSIC hub
- Ethernet
- 2nd alternative KSZ9031 ethernet phy
- Display connectors: PHYTEC LVDS, DDG LVDS, parallel signals, HDMI
- Parallel Camera CIF
- SGTL5000-32QFN audio codec
- 4x LEDs connected via PCA9533
- 2 user buttons
- Expansion connectors for WiFi and other modules
- RTC RV-4162-C7
- Resistive touch STMPE811
- EEPROM M24C32
ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:
Ralph Sennhauser [Thu, 30 Mar 2017 16:54:04 +0000 (18:54 +0200)]
ARM: dts: armada-385-linksys: disk-activity trigger for all
Commit a4ee7e18d808 ("ARM: dts: armada: Add default trigger for sata
led") adds the default trigger to individual boards, move it to
armada-385-linksys.dtsi which effectively enables the definition for
the WRT1900ACS (Shelby) as well as for future boards.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tony Lindgren [Tue, 4 Apr 2017 16:22:30 +0000 (09:22 -0700)]
ARM: dts: omap4-droid4: Stop disabling SRAM and GPMC
I disabled SRAM and GPMC originally when seeing errors with
omap_barriers_init(). But that is no longer happening probably
because the memory range is now properly configured to 1021 MB
instead of 1024 MB. So let's enable SRAM and GPMC so we get
omap_barriers_init() working and can idle the GPMC.
Cc: Marcel Partap <mpartap@gmx.net> Cc: Michael Scott <michael.scott@linaro.org> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Roger Quadros [Tue, 14 Mar 2017 12:50:21 +0000 (14:50 +0200)]
ARM: dts: am335x-icev2: Add CPSW ethernet0 and ethernet1
Enable the 2 ethernet ports as CPSW ports in dual-mac mode
Signed-off-by: Roger Quadros <rogerq@ti.com>
[nsekhar@ti.com: use AM33XX_IOPAD()] Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
projects / karo-tx-linux.git / log