]> git.karo-electronics.de Git - karo-tx-linux.git/log
karo-tx-linux.git
11 years agobatman-adv: switch to a new packet compatibility version
Antonio Quartulli [Sat, 20 Apr 2013 13:59:13 +0000 (15:59 +0200)]
batman-adv: switch to a new packet compatibility version

With this change batman-adv is breaking compatibility with
older versions and it is moving to compat-version 15.

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
11 years agoMAINTAINERS: batman-adv - update emails
Antonio Quartulli [Sat, 21 Sep 2013 11:46:56 +0000 (13:46 +0200)]
MAINTAINERS: batman-adv - update emails

Update my and Marek Lindner's email in the MAINTAINERS file

Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
11 years agobnx2x: Add ndo_get_phys_port_id support
Yuval Mintz [Wed, 9 Oct 2013 14:06:28 +0000 (16:06 +0200)]
bnx2x: Add ndo_get_phys_port_id support

Each network interface (either PF or VF) is identified by its port's MAC id.

Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: fix build errors if ipv6 is disabled
Eric Dumazet [Wed, 9 Oct 2013 10:05:48 +0000 (03:05 -0700)]
net: fix build errors if ipv6 is disabled

CONFIG_IPV6=n is still a valid choice ;)

It appears we can remove dead code.

Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoudp: fix a typo in __udp4_lib_mcast_demux_lookup
Eric Dumazet [Wed, 9 Oct 2013 04:47:29 +0000 (21:47 -0700)]
udp: fix a typo in __udp4_lib_mcast_demux_lookup

At this point sk might contain garbage.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoipv6: make lookups simpler and faster
Eric Dumazet [Thu, 3 Oct 2013 22:42:29 +0000 (15:42 -0700)]
ipv6: make lookups simpler and faster

TCP listener refactoring, part 4 :

To speed up inet lookups, we moved IPv4 addresses from inet to struct
sock_common

Now is time to do the same for IPv6, because it permits us to have fast
lookups for all kind of sockets, including upcoming SYN_RECV.

Getting IPv6 addresses in TCP lookups currently requires two extra cache
lines, plus a dereference (and memory stall).

inet6_sk(sk) does the dereference of inet_sk(__sk)->pinet6

This patch is way bigger than its IPv4 counter part, because for IPv4,
we could add aliases (inet_daddr, inet_rcv_saddr), while on IPv6,
it's not doable easily.

inet6_sk(sk)->daddr becomes sk->sk_v6_daddr
inet6_sk(sk)->rcv_saddr becomes sk->sk_v6_rcv_saddr

And timewait socket also have tw->tw_v6_daddr & tw->tw_v6_rcv_saddr
at the same offset.

We get rid of INET6_TW_MATCH() as INET6_MATCH() is now the generic
macro.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agotcp/dccp: remove twchain
Eric Dumazet [Thu, 3 Oct 2013 07:22:02 +0000 (00:22 -0700)]
tcp/dccp: remove twchain

TCP listener refactoring, part 3 :

Our goal is to hash SYN_RECV sockets into main ehash for fast lookup,
and parallel SYN processing.

Current inet_ehash_bucket contains two chains, one for ESTABLISH (and
friend states) sockets, another for TIME_WAIT sockets only.

As the hash table is sized to get at most one socket per bucket, it
makes little sense to have separate twchain, as it makes the lookup
slightly more complicated, and doubles hash table memory usage.

If we make sure all socket types have the lookup keys at the same
offsets, we can use a generic and faster lookup. It turns out TIME_WAIT
and ESTABLISHED sockets already have common lookup fields for IPv4.

[ INET_TW_MATCH() is no longer needed ]

I'll provide a follow-up to factorize IPv6 lookup as well, to remove
INET6_TW_MATCH()

This way, SYN_RECV pseudo sockets will be supported the same.

A new sock_gen_put() helper is added, doing either a sock_put() or
inet_twsk_put() [ and will support SYN_RECV later ].

Note this helper should only be called in real slow path, when rcu
lookup found a socket that was moved to another identity (freed/reused
immediately), but could eventually be used in other contexts, like
sock_edemux()

Before patch :

dmesg | grep "TCP established"

TCP established hash table entries: 524288 (order: 11, 8388608 bytes)

After patch :

TCP established hash table entries: 524288 (order: 10, 4194304 bytes)

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
David S. Miller [Wed, 9 Oct 2013 03:07:53 +0000 (23:07 -0400)]
Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Conflicts:
include/linux/netdevice.h
net/core/sock.c

Trivial merge issues.

Removal of "extern" for functions declaration in netdevice.h
at the same time "const" was added to an argument.

Two parallel line additions in net/core/sock.c

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'sfc-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfc
David S. Miller [Wed, 9 Oct 2013 01:56:09 +0000 (21:56 -0400)]
Merge branch 'sfc-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfc

Ben Hutchings says:

====================
Some more fixes for EF10 support; hopefully the last lot:

1. Fixes for reading statistics, from Edward Cree and Jon Cooper.
2. Addition of ethtool statistics for packets dropped by the hardware
before they were associated with a specific function, from Edward Cree.
3. Only bind to functions that are in control of their associated port,
as the driver currently assumes this is the case.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agopkt_sched: fq: fix non TCP flows pacing
Eric Dumazet [Tue, 8 Oct 2013 22:16:00 +0000 (15:16 -0700)]
pkt_sched: fq: fix non TCP flows pacing

Steinar reported FQ pacing was not working for UDP flows.

It looks like the initial sk->sk_pacing_rate value of 0 was
a wrong choice. We should init it to ~0U (unlimited)

Then, TCA_FQ_FLOW_DEFAULT_RATE should be removed because it makes
no real sense. The default rate is really unlimited, and we
need to avoid a zero divide.

Reported-by: Steinar H. Gunderson <sesse@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoRevert "veth: Showing peer of veth type dev in ip link (kernel side)"
David S. Miller [Wed, 9 Oct 2013 01:52:03 +0000 (21:52 -0400)]
Revert "veth: Showing peer of veth type dev in ip link (kernel side)"

This reverts commit 612c337306f00dc8d396830212de51c475844791.

As per Stephen Hemminger, the layout of the netlink attribute
is not implemented correctly so revert this for now.

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoqlcnic: add missing destroy_workqueue() on error path in qlcnic_probe()
Wei Yongjun [Tue, 8 Oct 2013 03:32:17 +0000 (11:32 +0800)]
qlcnic: add missing destroy_workqueue() on error path in qlcnic_probe()

Add the missing destroy_workqueue() before return from
qlcnic_probe() in the error handling case.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agomoxa: fix the error handling in moxart_mac_probe()
Wei Yongjun [Tue, 8 Oct 2013 03:19:19 +0000 (11:19 +0800)]
moxa: fix the error handling in moxart_mac_probe()

This patch fix the error handling in moxart_mac_probe():
 - return -ENOMEM in some memory alloc fail cases
 - add missing free_netdev() in the error handling case

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: vlan: fix nlmsg size calculation in vlan_get_size()
Marc Kleine-Budde [Mon, 7 Oct 2013 21:19:58 +0000 (23:19 +0200)]
net: vlan: fix nlmsg size calculation in vlan_get_size()

This patch fixes the calculation of the nlmsg size, by adding the missing
nla_total_size().

Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agopkt_sched: fq: fix typo for initial_quantum
Eric Dumazet [Mon, 7 Oct 2013 19:50:18 +0000 (12:50 -0700)]
pkt_sched: fq: fix typo for initial_quantum

TCA_FQ_INITIAL_QUANTUM should set q->initial_quantum

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoipv6: Fix the upper MTU limit in GRE tunnel
Oussama Ghorbel [Mon, 7 Oct 2013 17:50:05 +0000 (18:50 +0100)]
ipv6: Fix the upper MTU limit in GRE tunnel

Unlike ipv4, the struct member hlen holds the length of the GRE and ipv6
headers. This length is also counted in dev->hard_header_len.
Perhaps, it's more clean to modify the hlen to count only the GRE header
without ipv6 header as the variable name suggest, but the simple way to fix
this without regression risk is simply modify the calculation of the limit
in ip6gre_tunnel_change_mtu function.
Verified in kernel version v3.11.

Signed-off-by: Oussama Ghorbel <ou.ghorbel@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agocgroup: cls: remove unnecessary task_cls_classid
Gao feng [Tue, 8 Oct 2013 03:05:20 +0000 (11:05 +0800)]
cgroup: cls: remove unnecessary task_cls_classid

We can get classid through cgroup_subsys_state,
this is directviewing and effective.

Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agocgroup: netprio: remove unnecessary task_netprioidx
Gao feng [Tue, 8 Oct 2013 03:05:19 +0000 (11:05 +0800)]
cgroup: netprio: remove unnecessary task_netprioidx

Since the tasks have been migrated to the cgroup,
there is no need to call task_netprioidx to get
task's cgroup id.

Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: ipv4 only populate IP_PKTINFO when needed
Shawn Bohrer [Mon, 7 Oct 2013 16:01:40 +0000 (11:01 -0500)]
net: ipv4 only populate IP_PKTINFO when needed

The since the removal of the routing cache computing
fib_compute_spec_dst() does a fib_table lookup for each UDP multicast
packet received.  This has introduced a performance regression for some
UDP workloads.

This change skips populating the packet info for sockets that do not have
IP_PKTINFO set.

Benchmark results from a netperf UDP_RR test:
Before 89789.68 transactions/s
After  90587.62 transactions/s

Benchmark results from a fio 1 byte UDP multicast pingpong test
(Multicast one way unicast response):
Before 12.63us RTT
After  12.48us RTT

Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoudp: ipv4: Add udp early demux
Shawn Bohrer [Mon, 7 Oct 2013 16:01:39 +0000 (11:01 -0500)]
udp: ipv4: Add udp early demux

The removal of the routing cache introduced a performance regression for
some UDP workloads since a dst lookup must be done for each packet.
This change caches the dst per socket in a similar manner to what we do
for TCP by implementing early_demux.

For UDP multicast we can only cache the dst if there is only one
receiving socket on the host.  Since caching only works when there is
one receiving socket we do the multicast socket lookup using RCU.

For UDP unicast we only demux sockets with an exact match in order to
not break forwarding setups.  Additionally since the hash chains may be
long we only check the first socket to see if it is a match and not
waste extra time searching the whole chain when we might not find an
exact match.

Benchmark results from a netperf UDP_RR test:
Before 87961.22 transactions/s
After  89789.68 transactions/s

Benchmark results from a fio 1 byte UDP multicast pingpong test
(Multicast one way unicast response):
Before 12.97us RTT
After  12.63us RTT

Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoudp: Only allow busy read/poll on connected sockets
Shawn Bohrer [Mon, 7 Oct 2013 16:01:38 +0000 (11:01 -0500)]
udp: Only allow busy read/poll on connected sockets

UDP sockets can receive packets from multiple endpoints and thus may be
received on multiple receive queues.  Since packets packets can arrive
on multiple receive queues we should not mark the napi_id for all
packets.  This makes busy read/poll only work for connected UDP sockets.

This additionally enables busy read/poll for UDP multicast packets as
long as the socket is connected by moving the check into
__udp_queue_rcv_skb().

Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet_sched: increment drop counters in qdisc_tree_decrease_qlen()
Eric Dumazet [Mon, 7 Oct 2013 15:32:32 +0000 (08:32 -0700)]
net_sched: increment drop counters in qdisc_tree_decrease_qlen()

qdisc_tree_decrease_qlen() is called when some packets are dropped
on a qdisc, and we want to notify parents of qlen changes.

We also can increment parents qdisc qstats drop counters.

This permits more accurate drop counters up to root qdisc.

For example a graft operation typically resets a qdisc
(drops all packets) and call qdisc_tree_decrease_qlen()

Note that callers are responsible for their drop counters.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoxen-netback: transition to CLOSED when removing a VIF
David Vrabel [Mon, 7 Oct 2013 12:55:19 +0000 (13:55 +0100)]
xen-netback: transition to CLOSED when removing a VIF

If a guest is destroyed without transitioning its frontend to CLOSED,
the domain becomes a zombie as netback was not grant unmapping the
shared rings.

When removing a VIF, transition the backend to CLOSED so the VIF is
disconnected if necessary (which will unmap the shared rings etc).

This fixes a regression introduced by
279f438e36c0a70b23b86d2090aeec50155034a9 (xen-netback: Don't destroy
the netdev until the vif is shut down).

Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Paul Durrant <Paul.Durrant@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'mlx4'
David S. Miller [Tue, 8 Oct 2013 20:10:10 +0000 (16:10 -0400)]
Merge branch 'mlx4'

Amir Vadai says:

====================
net/mlx4_en: Fix pages never dma unmapped on rx

This patchset fixes a bug introduced by commit 51151a16 (mlx4: allow order-0
memory allocations in RX path). Where dma_unmap_page wasn't called.

Changes from V0:
- Added "Rename name of mlx4_en_rx_alloc members". Old names were confusing.
- Last frag in page calculation was wrong. Since all frags in page are of the
  same size, need to add this frag_stride to end of frag offset, and not the
  size of next frag in skb.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet/mlx4_en: Fix pages never dma unmapped on rx
Amir Vadai [Mon, 7 Oct 2013 11:38:13 +0000 (13:38 +0200)]
net/mlx4_en: Fix pages never dma unmapped on rx

This patch fixes a bug introduced by commit 51151a16 (mlx4: allow
order-0 memory allocations in RX path).

dma_unmap_page never reached because condition to detect last fragment
in page is wrong. offset+frag_stride can't be greater than size, need to
make sure no additional frag will fit in page => compare offset +
frag_stride + next_frag_size instead.
next_frag_size is the same as the current one, since page is shared only
with frags of the same size.

CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet/mlx4_en: Rename name of mlx4_en_rx_alloc members
Amir Vadai [Mon, 7 Oct 2013 11:38:12 +0000 (13:38 +0200)]
net/mlx4_en: Rename name of mlx4_en_rx_alloc members

Add page prefix to page related members: @size and @offset into
@page_size and @page_offset

CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agobonding: ensure that TLB mode's active slave has correct mac filter
Veaceslav Falico [Mon, 7 Oct 2013 07:17:20 +0000 (09:17 +0200)]
bonding: ensure that TLB mode's active slave has correct mac filter

Currently, in TLB mode we change mac addresses only by memcpy-ing the to
net_device->dev_addr, without actually setting them via
dev_set_mac_address(). This permits us to receive all the traffic always on
one mac address.

However, in case the interface flips, some drivers might enforce the
mac filtering for its FW/HW based on current ->dev_addr, and thus we won't
be able to receive traffic on that interface, in case it will be selected
as active in TLB mode.

Fix it by setting the mac address forcefully on every new active slave that
we select in TLB mode.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Yuval Mintz <yuvalmin@broadcom.com>
Reported-by: Yuval Mintz <yuvalmin@broadcom.com>
Tested-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: sh_eth: Fix RX packets errors on R8A7740
Nguyen Hong Ky [Mon, 7 Oct 2013 06:29:25 +0000 (15:29 +0900)]
net: sh_eth: Fix RX packets errors on R8A7740

This patch will fix RX packets errors when receiving big size
of data by set bit RNC = 1.

RNC - Receive Enable Control

0: Upon completion of reception of one frame, the E-DMAC writes
the receive status to the descriptor and clears the RR bit in
EDRRR to 0.

1: Upon completion of reception of one frame, the E-DMAC writes
(writes back) the receive status to the descriptor. In addition,
the E-DMAC reads the next descriptor and prepares for reception
of the next frame.

In addition, for get more stable when receiving packets, I set
maximum size for the transmit/receive FIFO and inserts padding
in receive data.

Signed-off-by: Nguyen Hong Ky <nh-ky@jinso.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agol2tp: Fix build warning with ipv6 disabled.
David S. Miller [Tue, 8 Oct 2013 19:44:26 +0000 (15:44 -0400)]
l2tp: Fix build warning with ipv6 disabled.

net/l2tp/l2tp_core.c: In function ‘l2tp_verify_udp_checksum’:
net/l2tp/l2tp_core.c:499:22: warning: unused variable ‘tunnel’ [-Wunused-variable]

Create a helper "l2tp_tunnel()" to facilitate this, and as a side
effect get rid of a bunch of unnecessary void pointer casts.

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agotun: don't look at current when non-blocking
Michael S. Tsirkin [Sun, 6 Oct 2013 18:25:12 +0000 (21:25 +0300)]
tun: don't look at current when non-blocking

We play with a wait queue even if socket is
non blocking. This is an obvious waste.
Besides, it will prevent calling the non blocking
variant when current is not valid.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'mrf24j40'
David S. Miller [Tue, 8 Oct 2013 19:32:19 +0000 (15:32 -0400)]
Merge branch 'mrf24j40'

Alan Ott says:

====================
Fix race conditions in mrf24j40 interrupts

After testing with the betas of this patchset, it's been rebased and is
ready for inclusion.

David Hauweele noticed that the mrf24j40 would hang arbitrarily after some
period of heavy traffic.  Two race conditions were discovered, and the
driver was changed to use threaded interrupts, since the enable/disable of
interrupts in the driver has recently been a lighning rod whenever issues
arise related to interrupts (costing engineering time), and since threaded
interrupts are the right way to do it.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agomrf24j40: Use level-triggered interrupts
Alan Ott [Sun, 6 Oct 2013 03:52:24 +0000 (23:52 -0400)]
mrf24j40: Use level-triggered interrupts

The mrf24j40 generates level interrupts. There are rare cases where it
appears that the interrupt line never gets de-asserted between interrupts,
causing interrupts to be lost, and causing a hung device from the driver's
perspective.  Switching the driver to interpret these interrupts as
level-triggered fixes this issue.

Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agomrf24j40: Use threaded IRQ handler
Alan Ott [Sun, 6 Oct 2013 03:52:23 +0000 (23:52 -0400)]
mrf24j40: Use threaded IRQ handler

Eliminate all the workqueue and interrupt enable/disable.

Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agomrf24j40: Move INIT_COMPLETION() to before packet transmission
Alan Ott [Sun, 6 Oct 2013 03:52:22 +0000 (23:52 -0400)]
mrf24j40: Move INIT_COMPLETION() to before packet transmission

This avoids a race condition where complete(tx_complete) could be called
before tx_complete is initialized.

Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch '6lowpan'
David S. Miller [Tue, 8 Oct 2013 19:28:53 +0000 (15:28 -0400)]
Merge branch '6lowpan'

Alan Ott says:

====================
Alexander Aring suggested that devices desired to be linked to 6lowpan
be checked for actually being of type IEEE802154, since IEEE802154 devices
are all that are supported by 6lowpan at present.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years ago6lowpan: Sync default hardware address of lowpan links to their wpan
Alan Ott [Sun, 6 Oct 2013 03:15:19 +0000 (23:15 -0400)]
6lowpan: Sync default hardware address of lowpan links to their wpan

When a lowpan link to a wpan device is created, set the hardware address
of the lowpan link to that of the wpan device.

Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years ago6lowpan: Only make 6lowpan links to IEEE802154 devices
Alan Ott [Sun, 6 Oct 2013 03:15:18 +0000 (23:15 -0400)]
6lowpan: Only make 6lowpan links to IEEE802154 devices

Refuse to create 6lowpan links if the actual hardware interface is
of any type other than ARPHRD_IEEE802154.

Signed-off-by: Alan Ott <alan@signal11.us>
Suggested-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoveth: Showing peer of veth type dev in ip link (kernel side)
Masatake YAMATO [Fri, 4 Oct 2013 02:34:21 +0000 (11:34 +0900)]
veth: Showing peer of veth type dev in ip link (kernel side)

ip link has ability to show extra information of net work device if
kernel provides sunh information. With this patch veth driver can
provide its peer ifindex information to ip command via netlink
interface.

Signed-off-by: Masatake YAMATO <yamato@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoRevert "xen-netback: improve ring effeciency for guest RX"
Wei Liu [Tue, 8 Oct 2013 09:54:21 +0000 (10:54 +0100)]
Revert "xen-netback: improve ring effeciency for guest RX"

This reverts commit 4f0581d25827d5e864bcf07b05d73d0d12a20a5c.

The named changeset is causing problem. Let's aim to make this part less
fragile before trying to improve things.

Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Annie Li <annie.li@oracle.com>
Cc: Matt Wilson <msw@amazon.com>
Cc: Xi Xiong <xixiong@amazon.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: Update the sysctl permissions handler to test effective uid/gid
Eric W. Biederman [Sat, 5 Oct 2013 20:15:30 +0000 (13:15 -0700)]
net: Update the sysctl permissions handler to test effective uid/gid

On Tue, 20 Aug 2013 11:40:04 -0500 Eric Sandeen <sandeen@redhat.com> wrote:
> This was brought up in a Red Hat bug (which may be marked private, I'm sorry):
>
> Bug 987055 - open O_WRONLY succeeds on some root owned files in /proc for process running with unprivileged EUID
>
> "On RHEL7 some of the files in /proc can be opened for writing by an unprivileged EUID."
>
> The flaw existed upstream as well last I checked.
>
> This commit in kernel v3.8 caused the regression:
>
> commit cff109768b2d9c03095848f4cd4b0754117262aa
> Author: Eric W. Biederman <ebiederm@xmission.com>
> Date:   Fri Nov 16 03:03:01 2012 +0000
>
>     net: Update the per network namespace sysctls to be available to the network namespace owner
>
>     - Allow anyone with CAP_NET_ADMIN rights in the user namespace of the
>       the netowrk namespace to change sysctls.
>     - Allow anyone the uid of the user namespace root the same
>       permissions over the network namespace sysctls as the global root.
>     - Allow anyone with gid of the user namespace root group the same
>       permissions over the network namespace sysctl as the global root group.
>
>     Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
>     Signed-off-by: David S. Miller <davem@davemloft.net>
>
> because it changed /sys/net's special permission handler to test current_uid, not
> current_euid; same for current_gid/current_egid.
>
> So in this case, root cannot drop privs via set[ug]id, and retains all privs
> in this codepath.

Modify the code to use current_euid(), and in_egroup_p, as in done
in fs/proc/proc_sysctl.c:test_perm()

Cc: stable@vger.kernel.org
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reported-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agocan: dev: fix nlmsg size calculation in can_get_size()
Marc Kleine-Budde [Sat, 5 Oct 2013 19:25:17 +0000 (21:25 +0200)]
can: dev: fix nlmsg size calculation in can_get_size()

This patch fixes the calculation of the nlmsg size, by adding the missing
nla_total_size().

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: wan: remove deprecated IRQF_DISABLED
Michael Opdenacker [Sat, 5 Oct 2013 04:45:30 +0000 (06:45 +0200)]
net: wan: remove deprecated IRQF_DISABLED

This patch proposes to remove the use of the IRQF_DISABLED flag

It's a NOOP since 2.6.35 and it will be removed one day.

Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoirda: remove deprecated IRQF_DISABLED
Michael Opdenacker [Sat, 5 Oct 2013 04:39:24 +0000 (06:39 +0200)]
irda: remove deprecated IRQF_DISABLED

This patch proposes to remove the use of the IRQF_DISABLED flag

It's a NOOP since 2.6.35 and it will be removed one day.

Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: hamradio/yam: remove deprecated IRQF_DISABLED
Michael Opdenacker [Sat, 5 Oct 2013 04:25:46 +0000 (06:25 +0200)]
net: hamradio/yam: remove deprecated IRQF_DISABLED

This patch proposes to remove the use of the IRQF_DISABLED flag

It's a NOOP since 2.6.35 and it will be removed one day.

Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: hamradio/scc: remove deprecated IRQF_DISABLED
Michael Opdenacker [Sat, 5 Oct 2013 04:22:30 +0000 (06:22 +0200)]
net: hamradio/scc: remove deprecated IRQF_DISABLED

This patch proposes to remove the use of the IRQF_DISABLED flag

It's a NOOP since 2.6.35 and it will be removed one day.

Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: fujitsu: Remove ISA depdendency from Kconfig
Matthew Whitehead [Fri, 4 Oct 2013 21:03:08 +0000 (17:03 -0400)]
net: fujitsu: Remove ISA depdendency from Kconfig

There no longer are ISA drivers in the fujitsu directory, so remove the
dependency from the Kconfig.

Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
David S. Miller [Mon, 7 Oct 2013 19:40:44 +0000 (15:40 -0400)]
Merge git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next

Conflicts:
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
drivers/net/wireless/rtlwifi/rtl8188ee/phy.h
drivers/net/wireless/rtlwifi/rtl8192ce/phy.h
drivers/net/wireless/rtlwifi/rtl8192de/phy.h
drivers/net/wireless/rtlwifi/rtl8723ae/phy.h

Just some minor conflicts between the wireless-next changes
and Joe Perches's "extern" removal from function prototypes
in header files.

John W. Linville says:

====================
Regarding the Bluetooth bits, Gustavo says:

"The big work here is from Marcel and Johan. They did a lot of work
in the L2CAP, HCI and MGMT layers. The most important ones are the
addition of a new MGMT command to enable/disable LE advertisement
and the introduction of the HCI user channel to allow applications
to get directly and exclusive access to Bluetooth devices."

As to the ath10k bits, Kalle says:

"Bartosz dropped support for qca98xx hw1.0 hardware from ath10k, it's
just too much to support it. Michal added support for the new firmware
interface. Marek fixed WEP in AP and IBSS mode. Rest of the changes are
minor fixes or cleanups."

And also:

"Major changes are:

* throughput improvements including aligning the RX frames correctly and
  optimising HTT layer (Michal)

* remove qca98xx hw1.0 support (Bartosz)

* add support for firmware version 999.999.0.636 (Michal)

* firmware htt statistics support (Kalle)

* fix WEP in AP and IBSS mode (Marek)

* fix a mutex unlock balance in debugfs file (Shafi)

And of course there's a lot of smaller fixes and cleanup."

For the wl12xx bits, Luca says:

"Here are some patches intended for 3.13.  Eliad is upstreaming a bunch
of patches that have been pending in the internal tree.  Mostly bugfixes
and other small improvements."

Along with that...

Arend and friends bring us a batch of brcmfmac updates, Larry Finger
offers some rtlwifi refactoring, and Sujith sends the usual batch of
ath9k updates.  As usual, there are a number of other small updates
from a variety of players as well.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoipv4: fix ineffective source address selection
Jiri Benc [Fri, 4 Oct 2013 15:04:48 +0000 (17:04 +0200)]
ipv4: fix ineffective source address selection

When sending out multicast messages, the source address in inet->mc_addr is
ignored and rewritten by an autoselected one. This is caused by a typo in
commit 813b3b5db831 ("ipv4: Use caller's on-stack flowi as-is in output
route lookups").

Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: Separate the close_list and the unreg_list v2
Eric W. Biederman [Sun, 6 Oct 2013 02:26:05 +0000 (19:26 -0700)]
net: Separate the close_list and the unreg_list v2

Separate the unreg_list and the close_list in dev_close_many preventing
dev_close_many from permuting the unreg_list.  The permutations of the
unreg_list have resulted in cases where the loopback device is accessed
it has been freed in code such as dst_ifdown.  Resulting in subtle memory
corruption.

This is the second bug from sharing the storage between the close_list
and the unreg_list.  The issues that crop up with sharing are
apparently too subtle to show up in normal testing or usage, so let's
forget about being clever and use two separate lists.

v2: Make all callers pass in a close_list to dev_close_many

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet/ethernet: cpsw: DT read bool dual_emac
Markus Pargmann [Fri, 4 Oct 2013 12:44:40 +0000 (14:44 +0200)]
net/ethernet: cpsw: DT read bool dual_emac

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: ethernet: cpsw: Search childs for slave nodes
Markus Pargmann [Fri, 4 Oct 2013 12:44:39 +0000 (14:44 +0200)]
net: ethernet: cpsw: Search childs for slave nodes

The current implementation searches the whole DT for nodes named
"slave".

This patch changes it to search only child nodes for slaves.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: fix unsafe set_memory_rw from softirq
Alexei Starovoitov [Fri, 4 Oct 2013 07:14:06 +0000 (00:14 -0700)]
net: fix unsafe set_memory_rw from softirq

on x86 system with net.core.bpf_jit_enable = 1

sudo tcpdump -i eth1 'tcp port 22'

causes the warning:
[   56.766097]  Possible unsafe locking scenario:
[   56.766097]
[   56.780146]        CPU0
[   56.786807]        ----
[   56.793188]   lock(&(&vb->lock)->rlock);
[   56.799593]   <Interrupt>
[   56.805889]     lock(&(&vb->lock)->rlock);
[   56.812266]
[   56.812266]  *** DEADLOCK ***
[   56.812266]
[   56.830670] 1 lock held by ksoftirqd/1/13:
[   56.836838]  #0:  (rcu_read_lock){.+.+..}, at: [<ffffffff8118f44c>] vm_unmap_aliases+0x8c/0x380
[   56.849757]
[   56.849757] stack backtrace:
[   56.862194] CPU: 1 PID: 13 Comm: ksoftirqd/1 Not tainted 3.12.0-rc3+ #45
[   56.868721] Hardware name: System manufacturer System Product Name/P8Z77 WS, BIOS 3007 07/26/2012
[   56.882004]  ffffffff821944c0 ffff88080bbdb8c8 ffffffff8175a145 0000000000000007
[   56.895630]  ffff88080bbd5f40 ffff88080bbdb928 ffffffff81755b14 0000000000000001
[   56.909313]  ffff880800000001 ffff880800000000 ffffffff8101178f 0000000000000001
[   56.923006] Call Trace:
[   56.929532]  [<ffffffff8175a145>] dump_stack+0x55/0x76
[   56.936067]  [<ffffffff81755b14>] print_usage_bug+0x1f7/0x208
[   56.942445]  [<ffffffff8101178f>] ? save_stack_trace+0x2f/0x50
[   56.948932]  [<ffffffff810cc0a0>] ? check_usage_backwards+0x150/0x150
[   56.955470]  [<ffffffff810ccb52>] mark_lock+0x282/0x2c0
[   56.961945]  [<ffffffff810ccfed>] __lock_acquire+0x45d/0x1d50
[   56.968474]  [<ffffffff810cce6e>] ? __lock_acquire+0x2de/0x1d50
[   56.975140]  [<ffffffff81393bf5>] ? cpumask_next_and+0x55/0x90
[   56.981942]  [<ffffffff810cef72>] lock_acquire+0x92/0x1d0
[   56.988745]  [<ffffffff8118f52a>] ? vm_unmap_aliases+0x16a/0x380
[   56.995619]  [<ffffffff817628f1>] _raw_spin_lock+0x41/0x50
[   57.002493]  [<ffffffff8118f52a>] ? vm_unmap_aliases+0x16a/0x380
[   57.009447]  [<ffffffff8118f52a>] vm_unmap_aliases+0x16a/0x380
[   57.016477]  [<ffffffff8118f44c>] ? vm_unmap_aliases+0x8c/0x380
[   57.023607]  [<ffffffff810436b0>] change_page_attr_set_clr+0xc0/0x460
[   57.030818]  [<ffffffff810cfb8d>] ? trace_hardirqs_on+0xd/0x10
[   57.037896]  [<ffffffff811a8330>] ? kmem_cache_free+0xb0/0x2b0
[   57.044789]  [<ffffffff811b59c3>] ? free_object_rcu+0x93/0xa0
[   57.051720]  [<ffffffff81043d9f>] set_memory_rw+0x2f/0x40
[   57.058727]  [<ffffffff8104e17c>] bpf_jit_free+0x2c/0x40
[   57.065577]  [<ffffffff81642cba>] sk_filter_release_rcu+0x1a/0x30
[   57.072338]  [<ffffffff811108e2>] rcu_process_callbacks+0x202/0x7c0
[   57.078962]  [<ffffffff81057f17>] __do_softirq+0xf7/0x3f0
[   57.085373]  [<ffffffff81058245>] run_ksoftirqd+0x35/0x70

cannot reuse jited filter memory, since it's readonly,
so use original bpf insns memory to hold work_struct

defer kfree of sk_filter until jit completed freeing

tested on x86_64 and i386

Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agosfc: Only bind to EF10 functions with the LinkCtrl and Trusted flags
Ben Hutchings [Mon, 7 Oct 2013 19:10:11 +0000 (20:10 +0100)]
sfc: Only bind to EF10 functions with the LinkCtrl and Trusted flags

Although we do not yet enable multiple PFs per port, it is possible
that a board will be reconfigured to enable them while the driver has
not yet been updated to fully support this.

The most obvious problem is that multiple functions may try to set
conflicting link settings.  But we will also run into trouble if the
firmware doesn't consider us fully trusted.  So, abort probing unless
both the LinkCtrl and Trusted flags are set for this function.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
11 years agoipv6: Allow the MTU of ipip6 tunnel to be set below 1280
Oussama Ghorbel [Thu, 3 Oct 2013 13:49:26 +0000 (14:49 +0100)]
ipv6: Allow the MTU of ipip6 tunnel to be set below 1280

The (inner) MTU of a ipip6 (IPv4-in-IPv6) tunnel cannot be set below 1280, which is the minimum MTU in IPv6.
However, there should be no IPv6 on the tunnel interface at all, so the IPv6 rules should not apply.
More info at https://bugzilla.kernel.org/show_bug.cgi?id=15530

This patch allows to check the minimum MTU for ipv6 tunnel according to these rules:
-In case the tunnel is configured with ipip6 mode the minimum MTU is 68.
-In case the tunnel is configured with ip6ip6 or any mode the minimum MTU is 1280.

Signed-off-by: Oussama Ghorbel <ou.ghorbel@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonetif_set_xps_queue: make cpu mask const
Michael S. Tsirkin [Wed, 2 Oct 2013 06:14:06 +0000 (09:14 +0300)]
netif_set_xps_queue: make cpu mask const

virtio wants to pass in cpumask_of(cpu), make parameter
const to avoid build warnings.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agosfc: Add PM and RXDP drop counters to ethtool stats
Edward Cree [Wed, 25 Sep 2013 16:32:09 +0000 (17:32 +0100)]
sfc: Add PM and RXDP drop counters to ethtool stats

Recognise the new Packet Memory and RX Data Path counters.

The following counters are added:
rx_pm_{trunc,discard}_bb_overflow - burst buffer overflowed.  This should not
 occur if BB correctly configured.
rx_pm_{trunc,discard}_vfifo_full - not enough space in packet memory.  May
 indicate RX performance problems.
rx_pm_{trunc,discard}_qbb - dropped by 802.1Qbb early discard mechanism.
 Since Qbb is not supported at present, this should not occur.
rx_pm_discard_mapping - 802.1p priority configured to be dropped.  This should
 not occur in normal operation.
rx_dp_q_disabled_packets - packet was to be delivered to a queue but queue is
 disabled.  May indicate misconfiguration by the driver.
rx_dp_di_dropped_packets - parser-dispatcher indicated that a packet should be
 dropped.
rx_dp_streaming_packets - packet was sent to the RXDP streaming bus, ie. a
 filter directed the packet to the MCPU.
rx_dp_emerg_{fetch,wait} - RX datapath had to wait for descriptors to be
 loaded.  Indicates performance problems but not drops.

These are only provided if the MC firmware has the
PM_AND_RXDP_COUNTERS capability.  Otherwise, mask them out.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
11 years agosfc: Add definitions for new stats counters and capability flag
Matthew Slattery [Tue, 10 Sep 2013 18:06:27 +0000 (19:06 +0100)]
sfc: Add definitions for new stats counters and capability flag

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
11 years agosfc: Refactor EF10 stat mask code to allow for more conditional stats
Edward Cree [Fri, 27 Sep 2013 17:52:49 +0000 (18:52 +0100)]
sfc: Refactor EF10 stat mask code to allow for more conditional stats

Previously, efx_ef10_stat_mask returned a static const unsigned long[], which
meant that each possible mask had to be declared statically with
STAT_MASK_BITMAP.  Since adding a condition would double the size of the
decision tree, we now create the bitmask dynamically.

To do this, we have two functions efx_ef10_raw_stat_mask, which returns a u64,
and efx_ef10_get_stat_mask, which fills in an unsigned long * argument.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
11 years agosfc: Fix internal indices of ethtool stats for EF10
Edward Cree [Wed, 25 Sep 2013 16:34:12 +0000 (17:34 +0100)]
sfc: Fix internal indices of ethtool stats for EF10

The indices in nic_data->stats need to match the EF10_STAT_whatever
enum values.  In efx_nic_update_stats, only mask; gaps are removed in
efx_ef10_update_stats.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
11 years agosfc: Add rmb() between reading stats and generation count to ensure consistency
Jon Cooper [Fri, 27 Sep 2013 17:26:30 +0000 (18:26 +0100)]
sfc: Add rmb() between reading stats and generation count to ensure consistency

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
11 years agotcp: do not forget FIN in tcp_shifted_skb()
Eric Dumazet [Fri, 4 Oct 2013 17:31:41 +0000 (10:31 -0700)]
tcp: do not forget FIN in tcp_shifted_skb()

Yuchung found following problem :

 There are bugs in the SACK processing code, merging part in
 tcp_shift_skb_data(), that incorrectly resets or ignores the sacked
 skbs FIN flag. When a receiver first SACK the FIN sequence, and later
 throw away ofo queue (e.g., sack-reneging), the sender will stop
 retransmitting the FIN flag, and hangs forever.

Following packetdrill test can be used to reproduce the bug.

$ cat sack-merge-bug.pkt
`sysctl -q net.ipv4.tcp_fack=0`

// Establish a connection and send 10 MSS.
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+.000 bind(3, ..., ...) = 0
+.000 listen(3, 1) = 0

+.050 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
+.000 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 6>
+.001 < . 1:1(0) ack 1 win 1024
+.000 accept(3, ..., ...) = 4

+.100 write(4, ..., 12000) = 12000
+.000 shutdown(4, SHUT_WR) = 0
+.000 > . 1:10001(10000) ack 1
+.050 < . 1:1(0) ack 2001 win 257
+.000 > FP. 10001:12001(2000) ack 1
+.050 < . 1:1(0) ack 2001 win 257 <sack 10001:11001,nop,nop>
+.050 < . 1:1(0) ack 2001 win 257 <sack 10001:12002,nop,nop>
// SACK reneg
+.050 < . 1:1(0) ack 12001 win 257
+0 %{ print "unacked: ",tcpi_unacked }%
+5 %{ print "" }%

First, a typo inverted left/right of one OR operation, then
code forgot to advance end_seq if the merged skb carried FIN.

Bug was added in 2.6.29 by commit 832d11c5cd076ab
("tcp: Try to restore large SKBs while SACK processing")

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next
David S. Miller [Fri, 4 Oct 2013 17:26:38 +0000 (13:26 -0400)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next

Pablo Neira Ayuso says:

====================
The following patchset contains Netfilter updates for your net-next tree,
mostly ipset improvements and enhancements features, they are:

* Don't call ip_nest_end needlessly in the error path from me, suggested
  by Pablo Neira Ayuso, from Jozsef Kadlecsik.

* Fixed sparse warnings about shadowed variable and missing rcu annotation
  and fix of "may be used uninitialized" warnings, also from Jozsef.

* Renamed simple macro names to avoid namespace issues, reported by David
  Laight, again from Jozsef.

* Use fix sized type for timeout in the extension part, and cosmetic
  ordering of matches and targets separatedly in xt_set.c, from Jozsef.

* Support package fragments for IPv4 protos without ports from Anders K.
  Pedersen. For example this allows a hash:ip,port ipset containing the
  entry 192.168.0.1,gre:0 to match all package fragments for PPTP VPN
  tunnels to/from the host. Without this patch only the first package
  fragment (with fragment offset 0) was matched.

* Introduced a new operation to get both setname and family, from Jozsef.
  ip[6]tables set match and SET target need to know the family of the set
  in order to reject adding rules which refer to a set with a non-mathcing
  family. Currently such rules are silently accepted and then ignored
  instead of generating an error message to the user.

* Reworked extensions support in ipset types from Jozsef. The approach of
  defining structures with all variations is not manageable as the
  number of extensions grows. Therefore a blob for the extensions is
  introduced, somewhat similar to conntrack. The support of extensions
  which need a per data destroy function is added as well.

* When an element timed out in a list:set type of set, the garbage
  collector skipped the checking of the next element. So the purging
  was delayed to the next run of the gc, fixed by Jozsef.

* A small Kconfig fix: NETFILTER_NETLINK cannot be selected and
  ipset requires it.

* hash:net,net type from Oliver Smith. The type provides the ability to
  store pairs of subnets in a set.

* Comment for ipset entries from Oliver Smith. This makes possible to
  annotate entries in a set with comments, for example:

  ipset n foo hash:net,net comment
  ipset a foo 10.0.0.0/21,192.168.1.0/24 comment "office nets A and B"

* Fix of hash types resizing with comment extension from Jozsef.

* Fix of new extensions for list:set type when an element is added
  into a slot from where another element was pushed away from Jozsef.

* Introduction of a common function for the listing of the element
  extensions from Jozsef.

* Net namespace support for ipset from Vitaly Lavrov.

* hash:net,port,net type from Oliver Smith, which makes possible
  to store the triples of two subnets and a protocol, port pair in
  a set.

* Get xt_TCPMSS working with net namespace, by Gao feng.

* Use the proper net netnamespace to allocate skbs, also by Gao feng.

* A couple of cleanups for the conntrack SIP helper, by Holger
  Eitzenberger.

* Extend cttimeout to allow setting default conntrack timeouts via
  nfnetlink, so we can get rid of all our sysctl/proc interfaces in
  the future for timeout tuning, from me.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agotcp: shrink tcp6_timewait_sock by one cache line
Eric Dumazet [Thu, 3 Oct 2013 21:27:25 +0000 (14:27 -0700)]
tcp: shrink tcp6_timewait_sock by one cache line

While working on tcp listener refactoring, I found that it
would really make things easier if sock_common could include
the IPv6 addresses needed in the lookups, instead of doing
very complex games to get their values (depending on sock
being SYN_RECV, ESTABLISHED, TIME_WAIT)

For this to happen, I need to be sure that tcp6_timewait_sock
and tcp_timewait_sock consume same number of cache lines.

This is possible if we only use 32bits for tw_ttd, as we remove
one 32bit hole in inet_timewait_sock

inet_tw_time_stamp() is defined and used, even if its current
implementation looks like tcp_time_stamp : We might need finer
resolution for tcp_time_stamp in the future.

Before patch : sizeof(struct tcp6_timewait_sock) = 0xc8

After patch : sizeof(struct tcp6_timewait_sock) = 0xc0

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoatl1e: enable support for NETIF_F_RXALL and NETIF_F_RXCRC features
Andrea Merello [Thu, 3 Oct 2013 19:18:37 +0000 (21:18 +0200)]
atl1e: enable support for NETIF_F_RXALL and NETIF_F_RXCRC features

This patch allows (optionally, via ethtool) the atl1e NIC to:
- Receive bad frames (runt, bad-fcs, etc..)
- Receive full frames without stripping the FCS.

This has been tested on my board by injecting runt and bad-fcs
frames with a FPGA-based device.

The particular scenario of receiving very short frames (<4 bytes)
without passing FCS to the upper layer has been also tested:
This could be potentially dangerous because the driver performs a
4 byte subtraction on the frame length, but I finally have NOT
added anything to avoid this because it seems the NIC always
discards frames so much short..
If someone still have some reason to worry about this, please
tell me.. I will add an explicit SW check..

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agowireless: rt2x00: rt2800usb: add new devices
Xose Vazquez Perez [Sat, 28 Sep 2013 11:07:10 +0000 (13:07 +0200)]
wireless: rt2x00: rt2800usb: add new devices

0411,0241  RT5572  BUFFALO WI-U2-300D Wireless LAN Adapter
0789,0170  RT3572  Logitec LAN-W300AN/U2
0846,9013  RT3573  NETGEAR Adaptador USB Inalambrico Movistar
0df6,006e  RT3573  Sitecom WiFi USB adapter N900
2001,3c1f  RT3573  D-Link DWA-162 Wireless N900 Dual Band Adapter
2001,3c20  RT5372  D-Link DWA-140 Wireless N USB Adapter(rev.D)
2001,3c21  RT5572  D-Link DWA-160 Xtreme N Dual Band USB Adapter(rev.C)
2001,3c22  RT5372  D-Link DWA-132 Wireless N USB Adapter(rev.B)
2001,3c23  RT5372  D-Link GO-USB-N300 Wireless N Easy USB Adapter
2019,ab29  ?       Planex GW-USMirco300
20f4,724a  RT5572  TRENDnet N600 Wireless Dual Band USB Adapter

Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: users@rt2x00.serialmonkey.com
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agortlwifi: rtl8188ee: Convert driver to use new rtl_phy_scan_operation_backup() routine
Larry Finger [Thu, 26 Sep 2013 18:25:33 +0000 (13:25 -0500)]
rtlwifi: rtl8188ee: Convert driver to use new rtl_phy_scan_operation_backup() routine

Now that rtl_phy_scan_operation_backup() exists, convert rtl8188ee to use it.
Routine rtl88e_phy_scan_operation_backup() is no longer used and is removed.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agortlwifi: rtl8723ae: Convert driver to use new rtl_phy_scan_operation_backup() routine
Larry Finger [Thu, 26 Sep 2013 18:25:32 +0000 (13:25 -0500)]
rtlwifi: rtl8723ae: Convert driver to use new rtl_phy_scan_operation_backup() routine

Now that rtl_phy_scan_operation_backup() exists, convert rtl8723ae to use it.
Routine rtl8723ae_phy_scan_operation_backup() is no longer used and is removed.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agortlwifi: rtl8192ce: Convert driver to use new rtl_phy_scan_operation_backup() routine
Larry Finger [Thu, 26 Sep 2013 18:25:31 +0000 (13:25 -0500)]
rtlwifi: rtl8192ce: Convert driver to use new rtl_phy_scan_operation_backup() routine

Now that rtl_phy_scan_operation_backup() exists, convert rtl8192de to use it.
Routine rtl92d_phy_scan_operation_backup() is no longer used and is removed.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agortlwifi: rtl8192c: Remove rtl8192c_phy_scan_operation_backup()
Larry Finger [Thu, 26 Sep 2013 18:25:30 +0000 (13:25 -0500)]
rtlwifi: rtl8192c: Remove rtl8192c_phy_scan_operation_backup()

Drivers rtl8192ce and rtl8192cu no longer rely on this routine. It is removed.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agortlwifi: rtl8192ce: Convert driver to use new rtl_phy_scan_operation_backup() routine
Larry Finger [Thu, 26 Sep 2013 18:25:29 +0000 (13:25 -0500)]
rtlwifi: rtl8192ce: Convert driver to use new rtl_phy_scan_operation_backup() routine

Now that rtl_phy_scan_operation_backup() exists, convert rtl8192ce to use it.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoMerge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville...
David S. Miller [Thu, 3 Oct 2013 20:28:18 +0000 (16:28 -0400)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless

John W. Linville says:

====================
Here is another batch of fixes intended for the 3.12 stream...

For the mac80211 bits, Johannes says:

"This time I have two fixes for IBSS (including one for wext, hah), a fix
for extended rates IEs, an active monitor checking fix and a sysfs
registration race fix."

On top of those...

Amitkumar Karwar brings an mwifiex fix for an interrupt loss issue
w/ SDIO devices.  The problem was due to a command timeout issue
introduced by an earlier patch.

Felix Fietkau a stall in the ath9k driver.  This patch fixes the
regression introduced in the commit "ath9k: use software queues for
un-aggregated data packets".

Stanislaw Gruszka reverts an rt2x00 patch that was found to cause
connection problems with some devices.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agortlwifi: rtl8192cu: Convert to use new rtl_phy_scan_operation_backup() routine
Larry Finger [Thu, 26 Sep 2013 18:25:28 +0000 (13:25 -0500)]
rtlwifi: rtl8192cu: Convert to use new rtl_phy_scan_operation_backup() routine

Now that the routine exists in driver rtlwifi, convert rtl8192cu to use it.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agortlwifi: Implement a common rtl_phy_scan_operation_backup() routine
Larry Finger [Thu, 26 Sep 2013 18:25:27 +0000 (13:25 -0500)]
rtlwifi: Implement a common rtl_phy_scan_operation_backup() routine

Several of the drivers supported by rtlwifi individually implement the same
routine that supports scans. As a first step, create this routine in
driver rtlwifi.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agortlwifi: Remove all remaining references to variable 'noise' in rtl_stats struct
Larry Finger [Wed, 25 Sep 2013 17:57:49 +0000 (12:57 -0500)]
rtlwifi: Remove all remaining references to variable 'noise' in rtl_stats struct

This completes removal of all places that reference variable 'noise'
in the rtl_stats struct. The definition of the struct is unchanged.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agortlwifi: rtl8188ee: Fix smatch warning in rtl8188ee/hw.c
Larry Finger [Wed, 25 Sep 2013 17:57:48 +0000 (12:57 -0500)]
rtlwifi: rtl8188ee: Fix smatch warning in rtl8188ee/hw.c

Smatch lists the following:
  CHECK   drivers/net/wireless/rtlwifi/rtl8188ee/hw.c
drivers/net/wireless/rtlwifi/rtl8188ee/hw.c:149 _rtl88ee_set_fw_clock_on() info: ignoring unreachable code.
drivers/net/wireless/rtlwifi/rtl8188ee/hw.c:149 _rtl88ee_set_fw_clock_on() info: ignoring unreachable code.

This info message is the result of a real error due to a missing break statement
in a "while (1)" loop.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.10+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agortlwifi: Fix smatch warnings in usb.c
Larry Finger [Wed, 25 Sep 2013 17:57:47 +0000 (12:57 -0500)]
rtlwifi: Fix smatch warnings in usb.c

Smatch displays the following:
  CHECK   drivers/net/wireless/rtlwifi/usb.c
drivers/net/wireless/rtlwifi/usb.c:458 _rtl_usb_rx_process_agg() warn: assigning (-98) to unsigned variable 'stats.noise'
drivers/net/wireless/rtlwifi/usb.c:503 _rtl_usb_rx_process_noagg() warn: assigning (-98) to unsigned variable 'stats.noise'
drivers/net/wireless/rtlwifi/usb.c:596 _rtl_rx_get_padding() info: ignoring unreachable code.
drivers/net/wireless/rtlwifi/usb.c:596 _rtl_rx_get_padding() info: ignoring unreachable code.

The variable 'stats.noise' is not used, thus the initializers are removed.
The unreachable code info is fixed by including the appropriate section inside
#ifdef .. #endif constructions.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agortlwifi: Fix smatch warning in pci.c
Larry Finger [Wed, 25 Sep 2013 17:57:46 +0000 (12:57 -0500)]
rtlwifi: Fix smatch warning in pci.c

Smatch reports the following:
  CHECK   drivers/net/wireless/rtlwifi/pci.c
drivers/net/wireless/rtlwifi/pci.c:739 _rtl_pci_rx_interrupt() warn: assigning (-98) to unsigned variable 'stats.noise'

The variable 'stats.noise' is not used. That initializer is removed.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agortlwifi: rtl8192_common: Fix smatch errors and warnings in rtl8192c/dm_common.c
Larry Finger [Wed, 25 Sep 2013 17:57:45 +0000 (12:57 -0500)]
rtlwifi: rtl8192_common: Fix smatch errors and warnings in rtl8192c/dm_common.c

Smatch lists the following:
  CHECK   drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:551 rtl92c_dm_pwdb_monitor() info: ignoring unreachable code.
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:551 rtl92c_dm_pwdb_monitor() info: ignoring unreachable code.
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:870 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:870 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:882 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:883 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:891 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:892 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2

The unreachable code message is fixed by deleting the code that follows a return.

The errors are fixed by increasing the size of txpwr_level.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agortlwifi: rtl8192cu: Fix smatch warning in rtl8192cu/trx.c
Larry Finger [Wed, 25 Sep 2013 17:57:44 +0000 (12:57 -0500)]
rtlwifi: rtl8192cu: Fix smatch warning in rtl8192cu/trx.c

Smatch lists the following:
  CHECK   drivers/net/wireless/rtlwifi/rtl8192cu/trx.c
drivers/net/wireless/rtlwifi/rtl8192cu/trx.c:367 _rtl_rx_process() warn: assigning (-98) to unsigned variable 'stats.noise'

This variable is unused, thus the initializer is removed, as well as a
comment referring to that variable.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agortlwifi: rtl8192de: Fix smatch warnings in rtl8192de/hw.c
Larry Finger [Wed, 25 Sep 2013 17:57:43 +0000 (12:57 -0500)]
rtlwifi: rtl8192de: Fix smatch warnings in rtl8192de/hw.c

Smatch lists the following:
  CHECK   drivers/net/wireless/rtlwifi/rtl8192de/hw.c
drivers/net/wireless/rtlwifi/rtl8192de/hw.c:1200 rtl92de_set_qos() info: ignoring unreachable code.
drivers/net/wireless/rtlwifi/rtl8192de/hw.c:1200 rtl92de_set_qos() info: ignoring unreachable code.

The dead code is deleted.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agortlwifi: rtl8192du: Fix smatch errors in /rtl8192de/dm.c
Larry Finger [Wed, 25 Sep 2013 17:57:42 +0000 (12:57 -0500)]
rtlwifi: rtl8192du: Fix smatch errors in /rtl8192de/dm.c

Smatch lists the following:
  CHECK   drivers/net/wireless/rtlwifi/rtl8192de/dm.c
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1054 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'ofdm_index' 2 <= 2
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1056 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'ofdm_index' 2 <= 2
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1126 rtl92d_dm_txpower_tracking_callback_thermalmeter() debug: remove_pools: nr_children over 4000 (4596). (rtlpriv->dbg.global_debuglevel merged)
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1126 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1129 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1132 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1135 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1138 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1141 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1144 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1147 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1151 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1154 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1157 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1160 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1163 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1166 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1169 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1172 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255

This patch fixes several off-by-one errors. It also removes a comment
referencing variable 'noise' in the rts_stats struct.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agort2800: add support for radio chip RF3070
Stanislaw Gruszka [Wed, 25 Sep 2013 13:34:55 +0000 (15:34 +0200)]
rt2800: add support for radio chip RF3070

Add support for new RF chip ID: 3070. It seems to be the same as 5370,
maybe vendor just put wrong value on the eeprom, but add this id anyway
since devices with it showed on the marked.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agobrcmfmac: rework rx path bus interface
Arend van Spriel [Wed, 25 Sep 2013 11:05:46 +0000 (13:05 +0200)]
brcmfmac: rework rx path bus interface

The brcmfmac has common and bus specific part. The rx function api
was using sk_buff_head. Changed to sk_buff instead.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agobrcmfmac: Use fw filename and nvram based of devid for sdio.
Hante Meuleman [Wed, 25 Sep 2013 11:05:45 +0000 (13:05 +0200)]
brcmfmac: Use fw filename and nvram based of devid for sdio.

SDIO firmware download routines uses one name for firmware file
and nvram file for all sdio devices. This is not user friendly.
Use fw filename and nvram filename based upon chip id and revision.

Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agobrcmfmac: fix sparse error 'bad constant expression'
Arend van Spriel [Wed, 25 Sep 2013 11:05:44 +0000 (13:05 +0200)]
brcmfmac: fix sparse error 'bad constant expression'

The definition of BRCMF_EVENTING_MASK_LEN results in a sparse
error message

.../fweh.c:331:22: error: bad constant expression
.../fweh.c:388:22: error: bad constant expression
.../dhd_common.c:256:22: error: bad constant expression

This is caused by the use of roundup() in BRCMF_EVENTING_MASK_LEN
and it is used to allocate an array variable on the stack. Better
use DIV_ROUND_UP() macro.

Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agobrcmfmac: reserve memory for bus layer in sk_buff::cb
Franky Lin [Wed, 25 Sep 2013 11:05:43 +0000 (13:05 +0200)]
brcmfmac: reserve memory for bus layer in sk_buff::cb

Bus layer need to share sk_buff::cb with firmware signal feature. Reserve
necessary memory so they won't overwrite each other.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agobrcmfmac: add valid core index check in related functions
Franky Lin [Wed, 25 Sep 2013 11:05:42 +0000 (13:05 +0200)]
brcmfmac: add valid core index check in related functions

Perform a valid check for core index to avoid illegal address access.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agobrcmfmac: add BCM4339 SDIO interface support
Franky Lin [Wed, 25 Sep 2013 11:05:41 +0000 (13:05 +0200)]
brcmfmac: add BCM4339 SDIO interface support

BCM4339 is an a/b/g/n/ac 1x1 WiFi chip. This patch adds support for it through
SDIO interface.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agobrcmfmac: sync firmware event list
Franky Lin [Wed, 25 Sep 2013 11:05:40 +0000 (13:05 +0200)]
brcmfmac: sync firmware event list

Update event list to keep sync with firmware development. Use calculated event
mask length instead of hard-coded value.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoMerge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetoot...
John W. Linville [Thu, 3 Oct 2013 20:19:07 +0000 (16:19 -0400)]
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

11 years agoMerge tag 'for-linville-20131001' of git://github.com/kvalo/ath
John W. Linville [Thu, 3 Oct 2013 20:16:34 +0000 (16:16 -0400)]
Merge tag 'for-linville-20131001' of git://github.com/kvalo/ath

11 years agoMerge branch 'for-linville' of git://git.kernel.org/pub/scm/linux/kernel/git/luca...
John W. Linville [Thu, 3 Oct 2013 20:15:35 +0000 (16:15 -0400)]
Merge branch 'for-linville' of git://git.kernel.org/pub/scm/linux/kernel/git/luca/wl12xx

11 years agonet: heap overflow in __audit_sockaddr()
Dan Carpenter [Wed, 2 Oct 2013 21:27:20 +0000 (00:27 +0300)]
net: heap overflow in __audit_sockaddr()

We need to cap ->msg_namelen or it leads to a buffer overflow when we
to the memcpy() in __audit_sockaddr().  It requires CAP_AUDIT_CONTROL to
exploit this bug.

The call tree is:
___sys_recvmsg()
  move_addr_to_user()
    audit_sockaddr()
      __audit_sockaddr()

Reported-by: Jüri Aedla <juri.aedla@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
John W. Linville [Thu, 3 Oct 2013 20:00:03 +0000 (16:00 -0400)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

11 years agoMerge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
David S. Miller [Thu, 3 Oct 2013 19:57:36 +0000 (15:57 -0400)]
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge

Included change:
- fix multi soft-interfaces setups with Network Coding enabled by
  registering the CODED packet type once only (instead of once per soft-if)

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years ago3com: Fix drivers/net/ethernet/3com/Kconfig references to PCMCIA and 3c515
Matthew Whitehead [Wed, 2 Oct 2013 15:08:03 +0000 (11:08 -0400)]
3com: Fix drivers/net/ethernet/3com/Kconfig references to PCMCIA and 3c515

The Vortex driver works with PCI and Cardbus devices, not PCMCIA.

There never was an EISA 3c515 card, only ISA, so remove that option.

Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: ipv4: Change variable type to bool
Peter Senna Tschudin [Wed, 2 Oct 2013 12:19:51 +0000 (14:19 +0200)]
net: ipv4: Change variable type to bool

The variable fully_acked is only assigned the values true and false.
Change its type to bool.

The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):

@exists@
type T;
identifier b;
@@
- T
+ bool
  b = ...;
  ... when any
  b = \(true\|false\)

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: myri10ge: Change variable type to bool
Peter Senna Tschudin [Wed, 2 Oct 2013 12:19:50 +0000 (14:19 +0200)]
net: myri10ge: Change variable type to bool

There is the rc variable on both myri10ge_ss_lock_napi and
myri10ge_ss_lock_poll functions. In both cases rc is only assigned the
values true and false. Both functions already return bool. Change rc
type to bool.

The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):

@exists@
type T;
identifier b;
@@
- T
+ bool
  b = ...;
  ... when any
  b = \(true\|false\)

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: bnx2x: Change variable type to bool
Peter Senna Tschudin [Wed, 2 Oct 2013 12:19:49 +0000 (14:19 +0200)]
net: bnx2x: Change variable type to bool

The variable rc is only assigned the values true and false.
The function bnx2x_prev_is_path_marked already returns bool.
Change rc type to bool.

The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):

@exists@
type T;
identifier b;
@@
- T
+ bool
  b = ...;
  ... when any
  b = \(true\|false\)

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: atl1c: Change variable type to bool
Peter Senna Tschudin [Wed, 2 Oct 2013 12:19:48 +0000 (14:19 +0200)]
net: atl1c: Change variable type to bool

The variable ret is only assigned the values true and false.
The function atl1c_read_eeprom already returns bool. Change
ret type to bool.

The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):

@exists@
type T;
identifier b;
@@
- T
+ bool
  b = ...;
  ... when any
  b = \(true\|false\)

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>