Chun-Yeow Yeoh [Sat, 15 Nov 2014 19:05:41 +0000 (03:05 +0800)]
ath9k_htc: Enable software crypto for mgmt frame in Tx for USB devices
In secured mesh, the unicast mgmt frame is encrypted using
the same key that used for encrypting the unicast data frame.
This patch "ath9k_htc_firmware: fix the offset of CCMP header
for mesh data frame" applied to open-ath9k-htc-firmware allows
the ath9k_htc to be loaded without "nohwcrypt=1". Unfortunately,
this is not working and we still need CCMP encryption of
transmitted management frames to be done in software.
So this patch allows the software encryption for transmitted
management frame to be done in software but remain the hardware
decryption for received management frame.
This patch is tested with the following hardwares:
- TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287]
- AR9271 802.11n
and managed to work with peer mesh STA equipped with ath9k.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chun-Yeow Yeoh [Sat, 15 Nov 2014 19:05:40 +0000 (03:05 +0800)]
ath9k|ath9k_htc: Seperate the software crypto flag for Tx and Rx
Use the sw_mgmt_crypto_tx flag to trigger the CCMP encryption
for transmitted management frames to be done in software while
the sw_mgmt_crypto_rx flag is used to trigger the CCMP decryption
for received management frames to be done in software.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Thu, 13 Nov 2014 16:24:16 +0000 (21:54 +0530)]
mwifiex: add auto TDLS support
This patch adds auto TDLS support to mwifiex.
Auto TDLS functionality works as follows:
1. Whenever userspace application has triggered TDLS connection with
any peer, driver would store this peer mac address details in its database.
2. After this driver whenever driver receives packet on direct link,
it would store rssi and timestamp in peer information.
3. Whenever a packet is to be transmitted to non-AP peer in station mode,
driver would check if TDLS link can be established by looking at peer RSSI
information. Driver would initiate TDLS setup in such cases.
4. Periodic timer is used for updating peer information.
5. Auto TDLS peer list & timer are cleared during disconnection or driver unload.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Thu, 13 Nov 2014 16:24:14 +0000 (21:54 +0530)]
mwifiex: do not explicitly disable TDLS link during teardown
When Teardown event from FW is indicated to userspace, userspace
would trigger tdls_oper handler to disable TDLS link.
We need not do this explicitly here.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chun-Yeow Yeoh [Wed, 12 Nov 2014 08:40:19 +0000 (16:40 +0800)]
ath9k: fix the assignment of hw queues for mesh interface
We need to assign the hw queues for mesh interface. Otherwise,
we are not able to bring up the mesh interface due to the
IEEE80211_INVAL_HW_QUEUE error.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Oleksij Rempel [Wed, 12 Nov 2014 07:32:08 +0000 (08:32 +0100)]
ath9k: common-spectral: don't depend from ATH9K_DEBUGFS
we can have here two variants. Add
ATH9K_CMN_DEBUGFS y if ATH9K_CMN_DEBUGFS || ATH9K_HTC_DEBUGFS
wich will add more configurations and testcases. Or remove ATH9K_HTC_DEBUGFS
which need more time to be done.
So, make common-spectral ignore ATH9K_DEBUGFS option for now.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/htc_drv_init.c:56:6: sparse: symbol 'ath9k_htc_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:61:6: sparse: symbol 'ath9k_htc_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:66:19: sparse: symbol 'ath9k_htc_ps_ops' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/init.c:91:6: sparse: symbol 'ath9k_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:96:6: sparse: symbol 'ath9k_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:101:19: sparse: symbol 'ath9k_ps_ops' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Wed, 5 Nov 2014 14:08:11 +0000 (19:38 +0530)]
mwifiex: module load parameter for interface creation
This patch adds module load parameter driver_mode for mwifiex
which would enable driver to create AP or P2P client interface while loading
module. driver_mode is bitmap of interface modes for station, AP and
P2P client.
Station interface is created by default and is unaffected by driver_mode
parameter.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 17 Nov 2014 20:28:39 +0000 (15:28 -0500)]
Merge branch 'for-linville' of git://github.com/kvalo/ath
Kalle Valo <kvalo@qca.qualcomm.com> says:
"One ath6kl patch and rest for ath10k, but nothing really major which
stands out. Most notable:
o fix resume (Bartosz)
o firmware restart is now faster and more reliable (Michal)
o it's now possible to test hardware restart functionality without
crashing the firmware using hw-restart parameter with
simulate_fw_crash debugfs file (Michal)"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Peter Oh [Mon, 17 Nov 2014 14:44:15 +0000 (16:44 +0200)]
ath10k: fix mismatched wmi api call
Fix to use v10.2 wmi call for firmware v10.2.
It turned out that peer association function was using
v10.1 wmi call for v10.2 firmware during code review.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k: handle ieee80211 header and payload tracing separately
For packet log, the transmitted frame 802.11 header alone is sufficient.
Recording entire packet is also consuming lot of disk space. To optimize
this, tx and rx data tracepoints are splitted into header and payload
tracepoints.
To record tx ieee80211 headers
trace-cmd record -e ath10k_tx_hdr
To record complete packets
trace-cmd record -e ath10k_tx_hdr -e ath10k_tx_payload
Cc: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
James Cameron [Tue, 11 Nov 2014 05:21:28 +0000 (16:21 +1100)]
mwifiex: simplify ad hoc join capability info
While preparing an ad-hoc start command, the capability info bitmap is
needlessly set from the command, and then the ESS bit cleared.
Change to set the bitmap directly without reference to the command.
Signed-off-by: James Cameron <quozl@laptop.org> Acked-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Mon, 10 Nov 2014 07:25:17 +0000 (09:25 +0200)]
wlcore: check minimum buffer size in some cmd_send functions
Check for the minimum required buffer length in wlcore_cmd_send() and
wlcore_cmd_configure_failsafe. This ensures that we will never try to
use a buffer that is smaller than the required header.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex: fix version display problem on big endian platforms
It's been observed that wrong firmware version (ex. 66.14.96.p9
instead of 14.66.9.p96) is displayed on big endian platforms.
The problem is fixed here.
Reported-by: Daniel Mosquera <daniel.mosquera@ctag.com> Tested-by: Daniel Mosquera <daniel.mosquera@ctag.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Wed, 5 Nov 2014 11:34:30 +0000 (17:04 +0530)]
mwifiex: do not setup AMPDU/AMSDU with broadcast receiver
It is observed that device sometimes sends BA setup requests for
broadcast mac address.
This patch adds a check to avoid checking availability of
AMPDU/AMSDU streams for broadcast mac address.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex: fix out of memory issue observed for USB chipsets
On some platforms, system goes out of memory during heavy
Rx traffic with our USB chipsets.
In case of SDIO/PCIe, after receiving 50 packets in Rx queue
we stop processing interrupts till packets pending fall below
low threshold i.e 20. We don't have similar logic for USB,
so if host platform is slow, we would hit a case where firmware
keeps on pushing packets at high speed than driver/kernel can
process.
We will stop submitting URBs for Rx data when pending packet
count reaches high threshold and restart them when enough
packets are consumed to solve the problem.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=85071 Reported-by: Marek Belisko <marek.belisko@gmail.com> Tested-by: Marek Belisko <marek.belisko@gmail.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Wed, 5 Nov 2014 11:34:27 +0000 (17:04 +0530)]
mwifiex: rx workqueue support for USB interface
This patch adds RX workqueue support for USB interfaces.
Currently rx_pending is applicable for cmd/events and Rx
data in USB interface. Let's use it only for Rx data.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sat, 1 Nov 2014 15:54:56 +0000 (16:54 +0100)]
bcma: get IRQ numbers from dt
It is not possible to auto detect the irq numbers used by the cores on
an arm SoC. If bcma was registered with device tree it will search for
some device tree nodes with the irq number and add it to the core
configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sat, 1 Nov 2014 15:54:55 +0000 (16:54 +0100)]
bcma: make it possible to specify a IRQ num in bcma_core_irq()
This moves bcma_core_irq() to main.c and add a extra parameter with a
number so that we can return different irq number for devices with more
than one.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Martin Townsend [Thu, 6 Nov 2014 19:15:13 +0000 (19:15 +0000)]
6lowpan: move skb_free from error paths in decompression
Currently we ensure that the skb is freed on every error path in IPHC
decompression which makes it easy to introduce skb leaks. By centralising
the skb_free into the receive function it makes future decompression routines
easier to maintain. It does come at the expense of ensuring that the skb
passed into the decompression routine must not be copied.
Signed-off-by: Martin Townsend <mtownsend1973@gmail.com> Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Acked-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Kuba Pawlak [Thu, 6 Nov 2014 18:36:52 +0000 (19:36 +0100)]
Bluetooth: Clear role switch pending flag
If role switch was rejected by the controller and HCI Event: Command Status
returned with status "Command Disallowed" (0x0C) the flag
HCI_CONN_RSWITCH_PEND remains set. No further role switches are
possible as this flag prevents us from sending any new HCI Switch Role
requests and the only way to clear it is to receive a valid
HCI Event Switch Role.
This patch clears the flag if command was rejected.
2013-01-01 00:03:44.209913 < HCI Command: Switch Role (0x02|0x000b) plen 7
bdaddr BC:C6:DB:C4:6F:79 role 0x00
Role: Master
2013-01-01 00:03:44.210867 > HCI Event: Command Status (0x0f) plen 4
Switch Role (0x02|0x000b) status 0x0c ncmd 1
Error: Command Disallowed
Signed-off-by: Kuba Pawlak <kubax.t.pawlak@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 5 Nov 2014 19:51:28 +0000 (20:51 +0100)]
mac802154: use IEEE802154_EXTENDED_ADDR_LEN
This patch removes the af_ieee802154 defines and use the
IEEE802154_EXTENDED_ADDR_LEN. We should do this everywhere in the
802.15.4 subsystem because af_ieee802154 should be normally an uapi
header.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 5 Nov 2014 19:51:27 +0000 (20:51 +0100)]
at86rf230: add force slotted operation bit
This patch adds a force setting of slotted operation bit. The atben
chips sometimes set these bit. The reason is unknown. Nevertheless we
don't support slotted operation so we set this bit now force while
probing.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 5 Nov 2014 19:51:25 +0000 (20:51 +0100)]
mac802154: add support for perm_extended_addr
This patch adding support for a perm extended address. This is useful
when a device supports an eeprom with a programmed static extended address.
If a device doesn't support such eeprom or serial registers then the
driver should generate a random extended address.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch cleanups the ieee802154_be64_to_le64 to have a similar
function like ieee802154_le64_to_be64 only with switched source and
destionation types.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 5 Nov 2014 19:51:20 +0000 (20:51 +0100)]
mac802154: add ieee802154_vif struct
This patch adds an ieee802154_vif similar like the ieee80211_vif which
holds the interface type and maybe further more attributes like the
ieee80211_vif structure.
Alexander Aring [Wed, 5 Nov 2014 19:51:19 +0000 (20:51 +0100)]
mac802154: add default interface registration
This patch adds a default interface registration for a wpan interface
type. Currently the 802.15.4 subsystem need to call userspace tools to
add an interface. This patch is like mac80211 handling for registration
a station interface type by default.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 5 Nov 2014 19:51:18 +0000 (20:51 +0100)]
ieee802154: remove mlme get_phy callback
This patch removes the get_phy callback from mlme ops structure. Instead
we doing a dereference via ieee802154_ptr dev pointer. For backwards
compatibility we need to run get_device after dereference wpan_phy via
ieee802154_ptr.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 5 Nov 2014 19:51:17 +0000 (20:51 +0100)]
ieee802154: rework interface registration
This patch meld mac802154_netdev_register into ieee802154_if_add
function. Also we have now only one alloc_netdev call with one interface
setup routine "ieee802154_if_setup" instead two different one for each
interface type. This patch checks via runtime the interface type and do
different handling now. Additional we add the wpan_dev struct in
ieee802154_sub_if_data and set the new ieee802154_ptr while netdev
registration. This behaviour is very similar the mac80211 netdev
registration functionality.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 5 Nov 2014 19:51:16 +0000 (20:51 +0100)]
mac802154: move dev_hold out of ieee802154_if_add
This patch moves the dev_hold call inside of nl-phy ieee802154_add_iface
function. The ieee802154_add_iface is the only one function which use the
ieee802154_if_add function and contains the corresponding dev_put call.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 5 Nov 2014 19:51:15 +0000 (20:51 +0100)]
mac802154: move interface add handling in iface
This patch moves and renames the mac802154_add_iface and
mac802154_netdev_register functions into iface.c. The function
mac802154_add_iface is renamed to ieee802154_if_add which is a similar naming
convention like mac80211.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 5 Nov 2014 19:51:14 +0000 (20:51 +0100)]
mac802154: move interface del handling in iface
This patch moves and rename the mac802154_del_iface function into
iface.c and rename the function to ieee802154_if_remove which is a similar
naming convention like mac80211.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 5 Nov 2014 19:51:13 +0000 (20:51 +0100)]
ieee802154: remove nl802154 unused functions
The include/net/nl802154.h file contains a lot of prototypes which are
not used inside of ieee802154 subsystem. This patch removes this file
and make the only one used prototype "ieee802154_nl_start_confirm" as
static declaration in ieee802154/nl-mac.c
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 5 Nov 2014 19:51:12 +0000 (20:51 +0100)]
ieee802154: rework wpan_phy index assignment
This patch reworks the wpan_phy index incrementation. It's now similar
like wireless wiphy index incrementation. We move the wpan_phy index
attribute inside of cfg802154_registered_device and use atomic
operations instead locking mechanism via wpan_phy_mutex.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Merge tag 'mac80211-next-for-john-2014-11-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"This relatively large batch of changes is comprised of the
following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions"
Dan Carpenter [Tue, 4 Nov 2014 08:55:09 +0000 (11:55 +0300)]
ieee802154: || vs && in ieee802154_is_valid_extended_addr()
The ieee802154_is_valid_extended_addr() always returns true because
there is a typo. The || should be &&. Neither 0x0000000000000000ULL
nor 0xffffffffffffffffULL are valid addresses.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Simon Vincent [Tue, 4 Nov 2014 15:29:51 +0000 (15:29 +0000)]
6lowpan: fix udp header compression when using raw sockets
If you use RAW sockets the transport header offset is not set by the
ipv6 stack so when we get to the udp header compression it does not
compress the right part of the packet.
This patch adds a check for this scenario and sets the transport
header offset.
Signed-off-by: Simon Vincent <simon.vincent@xsilon.com> Acked-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
mac80211: increase U-APSD max service period length
Deliver up to 128 frames during service period instead of 8 if
unlimited is specified by the client during association.
8 was just an arbitrary value; so is 128 since unlimited can
be any number.
However for large traffic bursts, increasing this value looks
reasonable. Also, it seems that a few certification tests
expect more frames to be delivered during SP.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 27 Oct 2014 11:03:19 +0000 (12:03 +0100)]
mac80211: handle RIC data element in reassociation request
When the RIC data element (RDE) is included in the IEs coming
from userspace for an association request, its handling is
currently broken as any IEs that are contained within it would
be split off from it and inserted again after all the IEs that
mac80211 generates (e.g. HT, VHT.)
To fix this, treat the RIC element specially, and stop after
it only when we find something that doesn't actually belong to
it. This assumes userspace is actually correctly building it,
directly after the fast BSS transition IE and before all the
others like extended capabilities.
This leaves as a potential problem the case where userspace is
building the following IEs:
In this case, we'd erroneously consider all three IEs to be
part of the RIC data together, and not split them between the
two vendor IEs. Unfortunately, it isn't easily possible to
distinguish vendor IEs, so this isn't easy to fix. Luckily,
this case is rare as normally wpa_supplicant will include an
extended capabilities IE in the IEs, and that certainly will
break the two vendor IEs apart correctly.
Reviewed-by: Eliad Peller <eliad@wizery.com> Reviewed-by: Beni Lev <beni.lev@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds new iface type (NL80211_IFTYPE_OCB) representing
the OCB (Outside the Context of a BSS) mode.
When establishing a connection to the network a cfg80211_join_ocb
function is called (particular nl80211_command is added as well).
A mandatory parameters during the ocb_join operation are 'center
frequency' and 'channel width (5/10 MHz)'.
Changes done in mac80211 are minimal possible required to avoid
many warnings (warning: enumeration value 'NL80211_IFTYPE_OCB'
not handled in switch) during compilation. Full functionality
(where needed) is added in the following patch.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Firmware was crashing when we were trying to warm reset it
after suspend. This was due to the fact that target registeres
can be accessed only if the hardware is awaken.
This patch makes sure to awake the device also on the hif up,
not only in case of probe call.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Existing implementation of reset_resume handler just calls
ath6kl_usb_remove() that deallocates all resources.
It can lead to double free, etc. on disconnect.
The patch removes reset_resume handler,
so usb core could conservatively reset the driver.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Alexander Aring [Sun, 2 Nov 2014 05:44:54 +0000 (06:44 +0100)]
netdevice: add ieee802154_ptr to net_device
This patch adds an ieee802154_ptr to the net_device structure.
Furthermore the 802.15.4 subsystem will introduce a nl802154 framework
which is similar like the nl80211 framework and a wpan_dev structure.
The wpan_dev structure will hold additional net_device attributes like
address options which are 802.15.4 specific. In the upcoming nl802154
implementation we will introduce a NL802154_FLAG_NEED_WPAN_DEV like
NL80211_FLAG_NEED_WDEV. For this flag an ieee802154_ptr in net_device is
needed. Additional we can access the wpan_dev attributes in upper layers
like IEEE 802.15.4 6LoWPAN easily. Current solution is a complicated
callback interface and getting these values over subif data structure
in mac802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Szymon Janc [Mon, 3 Nov 2014 13:20:56 +0000 (14:20 +0100)]
Bluetooth: Fix invalid response for 'Start Discovery' command
According to Management Interface API 'Start Discovery' command should
generate a Command Complete event on failure. Currently kernel is
sending Command Status on early errors. This results in userspace
ignoring such event due to invalid size.
bluetoothd[28499]: src/adapter.c:trigger_start_discovery()
bluetoothd[28499]: src/adapter.c:cancel_passive_scanning()
bluetoothd[28499]: src/adapter.c:start_discovery_timeout()
bluetoothd[28499]: src/adapter.c:start_discovery_complete() status 0x0a
bluetoothd[28499]: Wrong size of start discovery return parameters
Reported-by: Jukka Taimisto <jtt@codenomicon.com> Signed-off-by: Szymon Janc <szymon.janc@tieto.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Mon, 3 Nov 2014 04:16:08 +0000 (05:16 +0100)]
Bluetooth: Add hci_conn_lookup_type() helper function
Some drivers require knowledge of what connection handle is assigned
to what connection link type (ACL or SCO/eSCO). Instead of having each
driver implement connection tracking, provide a simple helper function
for lookup of the link type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Mon, 3 Nov 2014 04:16:07 +0000 (05:16 +0100)]
Bluetooth: btusb: Add internal callback for USB bulk rx data
Some vendors require special handling of the rx data from the USB
bulk endpoints. For that case provide an internal callback that
can overwrite it with a custom receive function.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Sun, 2 Nov 2014 20:46:52 +0000 (21:46 +0100)]
Bluetooth: Consolidate whitelist debugfs entry into device_list
The debufs entry for the BR/EDR whitelist is confusing since there is
a controller debugfs entry with the name white_list and both are two
different things.
With the BR/EDR whitelist, the actual interface in use is the device
list and thus just include all values from the internal BR/EDR whitelist
in the device_list debugfs entry.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Sun, 2 Nov 2014 19:52:24 +0000 (20:52 +0100)]
Bluetooth: Set HCI_QUIRK_STRICT_DUPLICATE_FILTER for Broadcom devices
The Bluetooth controllers from Broadcom use a strict scanning filter
policy that filters based on Bluetooth device addresses and not on
RSSI. So tell the core about this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some vendors decide to use a strict duplicate filter policy that only
filters on Bluetooth device addresses. This means that when the RSSI
changes, these devices are not reported again. During discovery it is
useful to actually get the RSSI updates.
Since this is specific to each controller, add a new quirk setting
that allows drivers to tell the core what kind of filtering policy
the controller uses.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Alexander Aring [Sun, 2 Nov 2014 20:43:06 +0000 (21:43 +0100)]
ieee802154: remove unnecessary functions
This patch fixes commit c7420c367d63a7e1414e010afb52c3837fd9134e
("mac802154: move mac_params functions into mac_cmd"). The mac_params
functions wasn't deleted by this commit.
Alexander Aring [Sun, 2 Nov 2014 20:43:04 +0000 (21:43 +0100)]
ieee802154: sysfs: add missing include
Running make C=2 occurs in warnings:
symbol 'wpan_phy_class' was not declared. Should it be static?
symbol 'wpan_phy_sysfs_init' was not declared. Should it be static?
symbol 'wpan_phy_sysfs_exit' wasnot declared. Should it be static?
This patch adds a missing include "sysfs.h" to solve these warnings.
Alexander Aring [Sun, 2 Nov 2014 20:43:03 +0000 (21:43 +0100)]
mac802154: fix byteorder issues
Running make C=2 occurs these warnings:
cast from restricted __be64
incorrect type in argument 1 (different base types)
expected unsigned long long[unsigned] [usertype] val
got restricted __be64 [usertype]<noident>
cast from restricted __be64
cast to restricted __le64
This patch fix these warnings by forcing to __le64 type and using swabp64
instead swab64.
projects / linux-beck.git / log